Linksys Network Router WRTU54G TM User Manual
2.4GHz  
802.11g  
Wireless-G  
Broadband Router  
with 2 Phone Ports  
User Guide  
WIRELESS  
Model No.  
WRTU54G-TM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Table of Contents  
Chapter 1: Introduction  
1
1
Welcome  
What’s in this User Guide?  
2
Chapter 2: Planning Your Wireless Network  
4
4
Network Topology  
Ad-Hoc versus Infrastructure Mode  
Network Layout  
4
4
Chapter 3: Getting to Know the Wireless-G Broadband Router  
6
6
The Back Panel  
The Front Panel  
7
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports  
8
8
Overview  
Hardware Installation for Connection to Your Broadband Modem  
Hardware Installation for Connection to An Existing Router  
Placement Options  
8
10  
12  
13  
SIM Card Installation  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports 14  
Overview  
The Setup Tab - Basic Setup  
The Setup Tab - DDNS  
14  
15  
19  
20  
21  
22  
23  
26  
27  
29  
29  
30  
32  
33  
34  
The Setup Tab - MAC Address Clone  
The Setup Tab - Advanced Routing  
The Wireless Tab - Basic Wireless Settings  
The Wireless Tab - Wireless Security  
The Wireless Tab - Wireless MAC Filter  
The Wireless Tab - Advanced Wireless Settings  
The Security Tab - Firewall  
The Security Tab - VPN Passthrough  
The Access Restrictions Tab - Internet Access  
The Applications and Gaming Tab - Port Range Forward  
The Applications & Gaming Tab - Port Triggering  
The Applications and Gaming Tab - DMZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Applications and Gaming Tab - QoS  
The Administration Tab - Management  
The Administration Tab - Log  
The Administration Tab - Diagnostics  
The Administration Tab - Factory Defaults  
The Administration Tab - Firmware Upgrade  
The Administration Tab - Config Management  
The Status Tab - Router  
34  
36  
36  
37  
38  
38  
38  
39  
40  
41  
42  
43  
43  
50  
57  
57  
57  
60  
The Status Tab - Local Network  
The Status Tab - Wireless  
The Status Tab - Voice  
Appendix A: Troubleshooting  
Common Problems and Solutions  
Frequently Asked Questions  
Appendix B: Wireless Security  
Security Precautions  
Security Threats Facing Wireless Networks  
Appendix C: Upgrading Firmware  
Appendix D: Windows Help  
61  
Appendix E: Finding the MAC Address and IP Address for Your  
Ethernet Adapter  
62  
62  
62  
63  
64  
Windows 2000 or XP Instructions  
Windows Vista Instructions  
For the Router’s Web-based Utility  
Appendix F: Glossary  
Appendix G: Specifications  
Appendix H: Warranty Information  
Appendix I: Regulatory Information  
71  
73  
74  
Appendix J: Software License Agreement  
Software in Linksys Products  
Schedule 1 - Linksys Software License Agreement  
Schedule 2  
81  
81  
81  
84  
Schedule 3  
89  
Schedule 4  
97  
Appendix K: Contact Information  
100  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
List of Figures  
Figure 3-1: The Router’s Back Panel  
6
7
8
9
9
Figure 3-2: The Router’s Front Panel  
Figure 4-1: Connecting Your Internet Connection  
Figure 4-2: Connecting Your Network Devices  
Figure 4-3: Connecting the Power  
Figure 4-4: Connecting the Phone  
9
Figure 4-5: Diagram for Connection to Another Router  
Figure 4-6: Connecting to Another Router  
Figure 4-7: Connecting Your Network Devices  
Figure 4-8: Connecting the Power  
10  
10  
10  
11  
11  
12  
13  
13  
13  
14  
15  
15  
15  
16  
16  
17  
17  
18  
18  
18  
19  
19  
20  
21  
21  
Figure 4-9: Connecting the Phone  
Figure 4-10: Measurement between Wall-Mount Slots  
Figure 4-11: Slide Down the SIM Card Cover  
Figure 4-12: Slide and Lift SIM Card Holder and Insert SIM Card  
Figure 4-13: Fold Down the SIM Card Holder and Slide into Place  
Figure 5-1: Password Screen  
Figure 5-2: Setup Tab - Basic Setup  
Figure 5-3: DHCP Connection Type  
Figure 5-4: Static IP Connection Type  
Figure 5-5: PPPoE Connection Type  
Figure 5-6: PPTP Connection Type  
Figure 5-7: L2TP Connection Type  
Figure 5-8: Optional Settings  
Figure 5-9: Router IP  
Figure 5-10: Network Address Server Settings  
Figure 5-11: Time Setting  
Figure 5-12: Setup Tab - DDNS  
Figure 5-13: Setup Tab - DDNS  
Figure 5-14: Setup Tab - MAC Address Clone  
Figure 5-15: Setup Tab - Advanced Routing (Router)  
Figure 5-16: Setup Tab - Advanced Routing (Bridge)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Figure 5-17: Wireless Tab - Basic Wireless Settings  
Figure 5-18: Wireless Tab - Wireless Security (WPA Personal)  
Figure 5-19: Wireless Tab - Wireless Security (WPA Enterprise)  
Figure 5-20: Wireless Tab - Wireless Security (WPA2 Personal)  
Figure 5-21: Wireless Tab - Wireless Security (WPA2 Enterprise)  
Figure 5-22: Wireless Tab - Wireless Security (RADIUS)  
Figure 5-23: Wireless Tab - Wireless Security (WEP)  
Figure 5-24: Wireless Tab - Wireless MAC Filter  
Figure 5-25: MAC Address Filter List  
Figure 5-26: Wireless Tab - Advanced Wireless Settings  
Figure 5-27: Security Tab - Firewall  
Figure 5-28: Security Tab - VPN Passthrough  
Figure 5-29: Access Restrictions Tab - Internet Access  
Figure 5-30: Internet Policy Summary  
22  
23  
23  
24  
24  
25  
25  
26  
26  
27  
29  
29  
30  
30  
30  
31  
32  
33  
34  
34  
36  
36  
37  
37  
37  
38  
38  
38  
39  
40  
40  
41  
42  
42  
Figure 5-31: List of PCs  
Figure 5-32: Port Services  
Figure 5-33: Applications and Gaming Tab - Port Range Forward  
Figure 5-34: Applications and Gaming Tab - Port Triggering  
Figure 5-35: Applications and Gaming Tab - DMZ  
Figure 5-36: Applications and Gaming Tab - QOS  
Figure 5-37: Administration Tab - Management  
Figure 5-38: Administration Tab - Log  
Figure 5-39: Administration Tab - Diagnostics  
Figure 5-40: The Ping Test  
Figure 5-41: The Traceroute Test  
Figure 5-42: Administration Tab - Factory Defaults  
Figure 5-43: Administration Tab - Firmware Upgrade  
Figure 5-44: Administration Tab - Config Management  
Figure 5-45: Status Tab - Router  
Figure 5-46: Status Tab - Local Network  
Figure 5-47: DHCP Clients Table  
Figure 5-48: Status Tab - Wireless  
Figure 5-49: Status Tab - Voice  
Figure 5-50: Status Tab - Voice - Call Log  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Figure 5-51: Status Tab - Voice - Error List  
Figure C-1: Upgrade Firmware  
Figure E-1: MAC Address/Physical Address  
Figure E-2: MAC Address Filter List  
Figure E-3: MAC Address Clone  
42  
60  
62  
62  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Chapter 1: Introduction  
Welcome  
NOTE: The Setup Wizard is not compatible with  
Mac® computers. Refer to Chapter 4: Connecting the  
Wireless-G Broadband Router with 2 Phone Ports and  
Chapter 5: Configuring the Wireless-G Broadband  
Router with 2 Phone Ports.  
Thank you for choosing the Linksys Wireless-G Broadband Router with 2 Phone Ports. The Wireless-G Broadband  
Router with 2 Phone Ports will allow you to network wirelessly better than ever, sharing Internet access, files and  
fun, easily and securely.  
How does the Wireless-G Broadband Router with 2 Phone Ports do all of this? A router is a device that allows  
access to an Internet connection over a network. With the Wireless-G Broadband Router with 2 Phone Ports, this  
access can be shared over the four switched ports or via the wireless broadcast at up to 11Mbps for Wireless-B  
or up to 54Mbps for Wireless-G.  
wpa (wi-fi protected access): a wireless security  
protocol using TKIP (Temporal Key Integrity Protocol)  
encryption, which can be used in conjunction with a  
RADIUS server.  
Use the WPA standard to secure your wireless network while the whole network is protected through a Stateful  
Packet Inspection (SPI) firewall and Network Address Translation (NAT) technology. Just run the Setup Wizard and  
it will guide you through the steps to set up your network. You can also access the Router’s features through the  
easy-to-use, browser-based utility.  
spi (stateful packet inspection) firewall: a technology  
that inspects incoming packets of information before  
allowing them to enter the network.  
But what does all of this mean?  
Networks are useful tools for sharing computer resources. You can access one printer from different computers  
and access data located on another computer's hard drive. Networks are even used for playing multiplayer video  
games. So, networks are not only useful in homes and offices, they can also be fun.  
firewall: Security measures that protect the  
resources of a local network from intruders.  
nat (network address translation): NAT technology  
translates IP addresses of a local area network to a  
different IP address for the Internet.  
PCs on a wired network create a LAN, or Local Area Network. They are connected with Ethernet cables, which is  
why the network is called “wired”.  
PCs equipped with wireless cards or adapters can communicate without cumbersome cables. By sharing the  
same wireless settings, within their transmission radius, they form a wireless network. This is sometimes called  
a WLAN, or Wireless Local Area Network. The Wireless-G Broadband Router with 2 Phone Ports bridges wireless  
networks of both 802.11b and 802.11g standards and wired networks, allowing them to communicate with each  
other.  
lan (local area network): The computers and  
networking products that make up the network in  
your home or office.  
With your networks all connected, wired, wireless, and the Internet, you can now share files and Internet  
access—and even play games. All the while, the Wireless-G Broadband Router with 2 Phone Ports protects your  
networks from unauthorized and unwelcome users.  
Linksys recommends using the Setup CD-ROM for first-time installation of the Router. If you do not wish to run  
the Setup Wizard on the Setup CD-ROM, then use the instructions in this Guide to help you connect the  
Chapter 1: Introduction  
Welcome  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Wireless-G Broadband Router with 2 Phone Ports, set it up, and configure it to bridge your different networks.  
These instructions should be all you need to get the most out of the Wireless-G Broadband Router with 2 Phone  
Ports.  
What’s in this User Guide?  
This user guide covers the steps for setting up and using the Wireless-G Broadband Router with 2 Phone Ports.  
•
•
•
•
•
Chapter 1: Introduction  
This chapter describes the Router’s applications and this User Guide.  
Chapter 2: Planning Your Wireless Network  
This chapter describes the basics of wireless networking.  
Chapter 3: Getting to Know the Wireless-G Broadband Router with 2 Phone Ports  
This chapter describes the physical features of the Router.  
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports  
This chapter instructs you on how to connect the Router to your network.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
This chapter explains how to use the Web-based Utility to configure the settings on the Wireless-G Broadband  
Router with 2 Phone Ports.  
•
Appendix A: Troubleshooting  
This appendix describes some problems and solutions, as well as frequently asked questions, regarding  
installation and use of the Wireless-G Broadband Router with 2 Phone Ports.  
•
•
•
Appendix B: Wireless Security  
This appendix explains the risks of wireless networking and some solutions to reduce the risks.  
Appendix C: Upgrading Firmware  
This appendix instructs you on how to upgrade the firmware on the Router should you need to do so.  
Appendix D: Windows Help  
This appendix describes how you can use Windows Help for instructions about networking, such as installing  
the TCP/IP protocol.  
•
Appendix E: Finding the MAC Address and IP Address for your Ethernet Adapter.  
This appendix describes how to find the MAC address for your computer’s Ethernet adapter so you can use  
the MAC filtering and/or MAC address cloning feature of the Router.  
Chapter 1: Introduction  
What’s in this User Guide?  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
•
•
•
•
•
Appendix F: Glossary  
This appendix gives a brief glossary of terms frequently used in networking.  
Appendix G: Specifications  
This appendix provides the technical specifications for the Router.  
Appendix H: Warranty Information  
This appendix supplies the warranty information for the Router.  
Appendix I: Regulatory Information  
This appendix supplies the regulatory information regarding the Router.  
Appendix J: Contact Information  
This appendix provides contact information for a variety of Linksys resources, including Technical Support.  
Chapter 1: Introduction  
What’s in this User Guide?  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Chapter 2: Planning Your Wireless Network  
Network Topology  
A wireless local area network (WLAN) is exactly like a regular local area network (LAN), except that each  
computer in the WLAN uses a wireless device to connect to the network. Computers in a WLAN share the same  
frequency channel and SSID, which is an identification name shared by the wireless devices belonging to the  
ssid (service set identifier): your wireless network’s name.  
same wireless network.  
Ad-Hoc versus Infrastructure Mode  
Unlike wired networks, wireless networks have two different modes in which they may be set up: infrastructure  
and ad-hoc. An infrastructure configuration is a WLAN and wired LAN communicating to each other through an  
access point. An ad-hoc configuration is wireless-equipped computers communicating directly with each other.  
Choosing between these two modes depends on whether or not the wireless network needs to share data or  
peripherals with a wired network or not.  
infrastructure: a wireless network that is bridged  
to a wired network via an access point.  
ad-hoc: a group of wireless devices  
communicating directly to each other (peer-to-  
peer) without the use of an access point.  
If the computers on the wireless network need to be accessible by a wired network or need to share a peripheral,  
such as a printer, with the wired network computers, the wireless network should be set up in Infrastructure  
mode. The basis of Infrastructure mode centers around a wireless router or an access point, such as the  
Wireless-G Broadband Router, which serves as the main point of communications in a wireless network. The  
Router transmits data to PCs equipped with wireless network adapters, which can roam within a certain radial  
range of the Router. You can arrange the Router and multiple access points to work in succession to extend the  
roaming range, and you can set up your wireless network to communicate with your Ethernet hardware as well.  
If the wireless network is relatively small and needs to share resources only with the other computers on the  
wireless network, then the Ad-Hoc mode can be used. Ad-Hoc mode allows computers equipped with wireless  
transmitters and receivers to communicate directly with each other, eliminating the need for a wireless router or  
access point. The drawback of this mode is that in Ad-Hoc mode, wireless-equipped computers are not able to  
communicate with computers on a wired network. And, of course, communication between the wireless-  
equipped computers is limited by the distance and interference directly between them.  
Network Layout  
The Wireless-G Broadband Router has been specifically designed for use with both your 802.11b and 802.11g  
products. Now, products using these standards can communicate with each other.  
Chapter 2: Planning Your Wireless Network  
Network Topology  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Wireless-G Broadband Router is compatible with all 802.11b and 802.11g adapters, such as the Notebook  
Adapters (WPC54G, WPC11) for your laptop computers, PCI Adapter (WMP54G, WMP11) for your desktop PC, and  
USB Adapter (WUSB54G, WUSB11) when you want to enjoy USB connectivity. The Broadband Router will also  
communicate with the Wireless PrintServer (WPS54G) and Wireless Ethernet Bridges (WET54G, WET11).  
When you wish to connect your wireless network with your wired network, you can use the Wireless-G  
Broadband Router’s four LAN ports. To add more ports, any of the Wireless-G Broadband Router's LAN ports can  
be connected to any of Linksys's switches (such as the SD205 or SD208).  
With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at  
www.linksys.com for more information about products that work with the Wireless-G Broadband Router.  
Chapter 2: Planning Your Wireless Network  
Network Layout  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Chapter 3: Getting to Know the Wireless-G Broadband  
Router  
The Back Panel  
The Router's ports, where the cables are connected, are located on the back panel.  
Figure 3-1: The Router’s Back Panel  
IMPORTANT: Resetting the Router will erase  
all of your settings (Internet connection,  
wireless security, and other settings) and  
replace them with the factory defaults. Do not  
reset the Router if you want to retain these  
settings.  
Internet  
The Internet port is where you will connect your broadband Internet connection.  
Ethernet 1-4  
These ports (1-4) connect the Router to your networked PCs and other Ethernet network  
devices.  
Phone1 /Phone2 You can connect a phone in each of these ports.  
Reset Button  
There are two ways to reset the Router's factory defaults. Either press the Reset Button, for  
approximately five seconds, or restore the defaults from the Administration tab - Factory  
Defaults in the Router's Web-based Utility.  
Power  
The Power port is where you will connect the power adapter.  
Chapter 3: Getting to Know the Wireless-G Broadband Router  
The Back Panel  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Front Panel  
The Router’s LEDs are located on the front panel.  
Figure 3-2: The Router’s Front Panel  
Power  
Green. The Power LED lights up and will stay on while the Router is powered on. When the  
Router goes through its self-diagnostic mode during every boot-up, this LED will flash. When  
the diagnostic is complete, the LED will be solidly lit.  
Ethernet 1-4  
Wireless  
Green. These numbered LEDs, corresponding with the numbered ports on the Router’s back  
panel, serve two purposes. If the LED is continuously lit, the Router is successfully connected  
to a device through that port. A flashing LED indicates network activity over that port.  
Green. The WLAN LED lights up whenever there is a successful wireless connection. If the LED  
is flashing, the Router is actively sending or receiving data over the network.  
Phone1/Phone2 Blue. This LED lights up blue when a SIM card is correctly installed and registered. It will blink  
when you have new voicemail.  
Internet  
Pairing  
Green. The Internet LED lights up when there is a connection made through the Internet port.  
The LED flashes when there is traffic.  
Green. The LED lights up green when wireless security is enabled. When the Pairing button is  
pushed, the Pairing LED flashes amber, then when the pairing is done, the LED lights up green.  
Chapter 3: Getting to Know the Wireless-G Broadband Router  
The Front Panel  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Chapter 4: Connecting the Wireless-G Broadband Router  
with 2 Phone Ports  
Overview  
This chapter includes two sets of connection instructions. If the Wireless-G Broadband Router with 2 Phone Ports  
will be the only router in your network, follow the instructions in “Hardware Installation for Connection to Your  
Broadband Modem.” If you want to install the Wireless-G Broadband Router with 2 Phone Ports behind an existing  
router in your network, then follow the instructions in “Hardware Installation for Connection to an existing  
Router.” Also included are Placement instructions, and SIM Card Installation instructions.  
Hardware Installation for Connection to Your Broadband Modem  
1. Power down your network devices.  
2. Locate an optimum location for the Router. The best place for the Router is usually at the center of your  
wireless network, with line of sight to all of your mobile stations.  
3. Fix the direction of the antennas. Try to place the Router in a position that will best cover your wireless  
network. Normally, the higher you place the antenna, the better the performance will be.  
4. Connect a standard Ethernet network cable to the Router’s Internet port. Then, connect the other end of the  
Ethernet cable to your cable or DSL broadband modem.  
Figure 4-1: Connecting Your Internet Connection  
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports  
Overview  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
5. Connect your network PCs or Ethernet devices to the Router’s numbered ports using standard Ethernet  
network cabling.  
Figure 4-2: Connecting Your Network Devices  
6. Connect the AC power adapter to the Router's Power port and the other end into an electrical outlet. Only use  
the power adapter supplied with the Router. Use of a different adapter may damage the product.  
IMPORTANT: Make sure you use the power  
adapter that is supplied with the Router. Use of a  
different power adapter could damage the Router.  
Figure 4-3: Connecting the Power  
7. Connect a standard telephone to the Router’s Phone1 port. If you have a second phone, connect the telephone to the  
Router’s Phone2 port.  
IMPORTANT: Do not connect the Phone port to a  
telephone wall jack. Make sure you only connect a  
telephone to the Phone port. Otherwise, the Router or the  
telephone wiring in your home or office may be damaged.  
Figure 4-4: Connecting the Phone  
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports  
Hardware Installation for Connection to Your Broadband Modem  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Now that the hardware installation is complete, proceed to “Chapter 5: Configuring the Wireless-G  
Broadband Router with 2 Phone Ports,” for directions on how to configure the Router.  
Hardware Installation for Connection to An Existing Router  
Your existing Router may have the same default IP address (192.168.0.1) as your new T-Mobile router. If this is  
the case, the T-Mobile router’s IP address will change to 192.168.24.1.  
1. Power down your network devices. Now you will begin the hardware installation of router.  
2. Locate an optimum location for the Router. The best place for the router is usually at the center of your  
wireless network, with line of sight to all of your mobile stations.  
Broadband  
Modem  
Internet  
3. Fix the direction of the antennas. Try to place the Router in a position that will best cover your wireless  
network. Normally, the higher you place the antenna, the better the performance will be.  
4. Connect a standard Ethernet network cable to the T-Mobile router’s Internet port. Then, connect the other end  
of the Ethernet cable to one of the numbered Ethernet ports on your existing router.  
Router  
Wireless-G  
Broadband  
Router  
Figure 4-6: Connecting to Another Router  
with 2 Phone  
Ports  
5. Decide which network computers or Ethernet devices you want to connect to the Router.  
Multiple PCs  
Figure 4-5: Diagram for Connection to Another Router  
Figure 4-7: Connecting Your Network Devices  
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports  
Hardware Installation for Connection to An Existing Router  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
6. Disconnect the selected computers or devices from the old router, and then connect them to the T-Mobile  
router’s numbered ports using standard Ethernet network cabling.  
7. Connect the AC power adapter to the T-Mobile router's power port and the other end into an electrical outlet.  
Only use the power adapter supplied with the T-Mobile router. Use of a different adapter may result in product  
damage.  
Figure 4-8: Connecting the Power  
IMPORTANT: Make sure you use the power  
adapter that is supplied with the Router. Use of a  
different power adapter could damage the Router.  
8. Connect a standard telephone to the Router’s Phone1 port. If you have a second phone, connect the telephone to the  
Router’s Phone2 port.  
Figure 4-9: Connecting the Phone  
IMPORTANT: Do not connect the Phone port to a  
telephone wall jack. Make sure you only connect a  
telephone to the Phone port. Otherwise, the Router or the  
telephone wiring in your home or office may be damaged.  
Now that the hardware installation is complete, proceed to “Chapter 5: Configuring the Wireless-G  
Broadband Router with 2 Phone Ports,” for directions on how to configure the Router.  
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports  
Hardware Installation for Connection to An Existing Router  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Placement Options  
There are three ways to place the Router. The first way is to place it horizontally on a surface, so it sits on its four rubber feet.  
Another option is to install the stand onto the bottom of the Router, so the Router is in an upright position. Make sure to place  
the Router’s bottom edge of the Cisco logo in between the stand’s prongs until tight. The third way is to mount it on a wall.This  
option uses the Router’s four wall-mount slots on its bottom panel. The distance between two adjacent slots is 60 mm (2.36  
inches).  
To use the wall-mount option, follow these instructions:  
1. Make sure you have four screws that are size #4—this indicates a diameter measurement of 2.845 mm (0.112 inches).  
2. Determine where you want to mount the Router.  
3. Drill four holes into the wall. Make sure adjacent holes are 60 mm (2.36 inches) apart.  
4. Insert a screw into each hole, and leave 5 mm (0.2 inches) of its head exposed.  
5. Maneuver the Router so the wall-mount slots line up with the four screws.  
60 mm  
(2.36 inches)  
6. Place the wall-mount slots over the screws and slide the Router down until the screws fit snugly into the wall-mount  
slots.  
Proceed to “Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports” for directions  
on how to configure the Router.  
Figure 4-10: Measurement between Wall-  
Mount Slots  
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports  
Placement Options  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
SIM Card Installation  
Two SIM cards are required for a 2-line configuration.  
To install a SIM card, follow these steps:  
1. Slide the SIM card cover down, then lift off.  
1
2. Gently slide up the SIM card holder. Then from the bottom side, carefully lift up the SIM card holder. Do not lift  
the holder until it is correctly in place or it could break.  
Figure 4-11: Slide Down the SIM Card Cover  
3. Position the SIM card with the gold metal side up and towards the card slot opening. Carefully insert the SIM  
card into the slot until it lines up with the bottom edge of the top piece of the holder and before it hits the  
bottom piece of the holder or the SIM card or holder could break.  
Bottom Piece  
of Holder  
Slide SIM in only this far  
and not to the bottom  
4. Fold down the SIM card holder and slide down into place.  
Bottom Side  
5. Replace the SIM card cover. You might need to push it hard to lock it in place.  
3
2
Slide up SIM card holder this  
direction  
Top Piece of  
Holder  
Figure 4-12: Slide and Lift SIM Card Holder and Insert SIM Card  
4
Figure 4-13: Fold Down the SIM Card Holder and Slide into  
Place  
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports  
SIM Card Installation  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Chapter 5: Configuring the Wireless-G Broadband  
Router with 2 Phone Ports  
Overview  
NOTE: For first-time installation, Linksys  
recommends using the Setup Wizard on the Setup  
CD-ROM. If you want to configure advanced settings,  
use this chapter to learn about the Web-based Utility.  
Linksys recommends using the Setup CD-ROM for first-time installation of the Router. If you do not wish to run  
the Setup Wizard on the Setup CD-ROM, then you can use the Web-based Utility to configure the Router. For  
advanced users, you may configure the Router’s advanced settings through the Web-based Utility.  
HAVE YOU: Enabled TCP/IP on your PCs? PCs  
communicate over the network with this protocol.  
Refer to “Appendix D: Windows Help” for more  
information on TCP/IP.  
This chapter will describe each web page in the Utility and each page’s key functions. The utility can be accessed  
via your web browser through use of a computer connected to the Router. For a basic network setup, most users  
will use these two screens of the Utility:  
•
•
Basic Setup. On the Basic Setup screen, enter the settings provided by your ISP.  
Management. Click the Administration tab and then the Management tab. The Router’s default password is  
admin. To secure the Router, change the Password from its default.  
There are seven main tabs: Setup, Wireless, Security, Access Restrictions, Applications & Gaming, Administration,  
and Status. Additional tabs will be available after you click one of the main tabs.  
To access the Web-based Utility, launch Internet Explorer or Netscape Navigator, and enter the Router’s default IP  
address, 192.168.0.1, in the Address field. Then press Enter.  
A password request page, shown in Figure 5-1 will appear. (Non-Windows XP users will see a similar screen.)  
Leave the User Name field blank. The first time you open the Web-based Utility, use the default password admin.  
(You can set a new password from the Administration tab’s Management screen.) Then click the OK button.  
Figure 5-1: Password Screen  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
Overview  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Setup Tab - Basic Setup  
The first screen that appears displays the Setup tab. This allows you to change the Router's general settings.  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
Internet Setup  
The Internet Setup section configures the Router to your Internet connection. Most of this information can be  
obtained through your ISP.  
Internet Connection Type  
Choose the type of Internet connection your ISP provides from the drop-down menu.  
•
DHCP. By default, the Router’s Internet Connection Type is set to Automatic Configuration - DHCP, which  
should be kept only if your ISP supports DHCP or you are connecting through a dynamic IP address.  
•
Static IP. If you are required to use a permanent IP address to connect to the Internet, select Static IP.  
Figure 5-2: Setup Tab - Basic Setup  
Figure 5-3: DHCP Connection Type  
Internet IP Address. This is the Router’s IP address, when seen from the Internet. Your ISP will provide you  
with the IP Address you need to specify here.  
Subnet Mask. This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Your ISP  
will provide you with the Subnet Mask.  
Gateway. Your ISP will provide you with the Gateway Address, which is the ISP server’s IP address.  
DNS. Your ISP will provide you with at least one DNS (Domain Name System) Server IP Address.  
Figure 5-4: Static IP Connection Type  
Static IP address: a fixed address  
assigned to a computer or device  
connected to a network.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Setup Tab - Basic Setup  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
•
PPPoE. Some DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet  
connections. If you are connected to the Internet through a DSL line, check with your ISP to see if they use  
PPPoE. If they do, you will have to enable PPPoE.  
User Name and Password. Enter the User Name and Password provided by your ISP.  
Connect on Demand: Max Idle Time. You can configure the Router to cut the Internet connection after it has  
been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated  
due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as  
soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio  
button. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet  
connection terminates.  
Figure 5-5: PPPoE Connection Type  
•
PPTP. Point-to-Point Tunneling Protocol (PPTP) is a service that applies to connections in Europe only.  
Specify Internet IP Address. This is the Router’s IP address, as seen from the Internet. Your ISP will provide  
you with the IP Address you need to specify here.  
Subnet Mask. This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Your ISP  
will provide you with the Subnet Mask.  
Gateway. Your ISP will provide you with the Gateway Address.  
User Name and Password. Enter the User Name and Password provided by your ISP.  
Connect on Demand: Max Idle Time. You can configure the Router to cut the Internet connection after it has  
been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated  
due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as  
soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio  
button. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet  
connection terminates.  
Figure 5-6: PPTP Connection Type  
•
L2TP. Layer 2 Tunneling Protocol (L2TP) is used by some ISPs in Europe.  
User Name and Password. Enter the User Name and Password provided by your ISP.  
Specify IP Address of L2TP Server. Your ISP will provide you with the IP Address you need to specify here.  
Connect on Demand: Max Idle Time. You can configure the Router to cut the Internet connection after it has  
been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated  
due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as  
soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Setup Tab - Basic Setup  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
button. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet  
connection terminates.  
Optional Settings  
Some of these settings may be required by your ISP. Verify with your ISP before making any changes.  
Router Name. In this field, you can type a name of up to 39 characters to represent the Router.  
Figure 5-7: L2TP Connection Type  
Host Name/Domain Name. These fields allow you to supply a host and domain name for the Router. Some ISPs,  
usually cable ISPs, require these names as identification. You may have to check with your ISP to see if your  
broadband Internet service has been configured with a host and domain name. In most cases, leaving these  
fields blank will work.  
MTU. MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet  
transmission. The default setting, Manual, allows you to enter the largest packet size that will be transmitted.  
The recommended size, entered in the Size field, is 1492. You should leave this value in the 1200 to 1500 range.  
To have the Router select the best MTU for your Internet connection, select Auto.  
Network Setup  
The Network Setup section changes the settings on the network connected to the Router’s Ethernet ports.  
Wireless Setup is performed through the Wireless tab.  
Figure 5-8: Optional Settings  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Setup Tab - Basic Setup  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Router IP  
This presents both the Router’s IP Address and Subnet Mask as seen by your network.  
Network Address Server Settings (DHCP)  
Figure 5-9: Router IP  
The settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The  
Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to  
each computer on your network. If you choose to enable the Router’s DHCP server option, you must configure all  
of your network PCs to connect to a DHCP server (the Router), and make sure there is no other DHCP server on  
your network.  
DHCP Server. DHCP is enabled by factory default. If you already have a DHCP server on your network, or you  
don’t want a DHCP server, then click the Disable radio button (no other DHCP features will be available).  
Starting IP Address. Enter a value for the DHCP server to start with when issuing IP addresses. Because the  
Router’s default IP address is 192.168.0.1, the Starting IP Address must be 192.168.0.2 or greater, but smaller  
than 192.168.0.253. The default Starting IP Address is 192.168.0.100.  
Maximum Number of DHCP Users. Enter the maximum number of PCs that you want the DHCP server to assign  
IP addresses to. This number cannot be greater than 253. The default is 64.  
Client Lease Time. The Client Lease Time is the amount of time a network user will be allowed connection to the  
Router with their current dynamic IP address. Enter the amount of time, in minutes, that the user will be “leased”  
this dynamic IP address. After the time is up, the user will be automatically assigned a new dynamic IP address.  
The default is 0 minutes, which means one day.  
Figure 5-10: Network Address Server Settings  
Static DNS (1-3). The Domain Name System (DNS) is how the Internet translates domain or website names into  
Internet addresses or URLs. Your ISP will provide you with at least one DNS Server IP Address. If you wish to use  
another, type that IP Address in one of these fields. You can type up to three DNS Server IP Addresses here. The  
Router will use these for quicker access to functioning DNS servers.  
WINS. The Windows Internet Naming Service (WINS) manages each PC’s interaction with the Internet. If you use  
a WINS server, enter that server’s IP Address here. Otherwise, leave this blank.  
Time Setting  
Change the time zone in which your network functions from this pull-down menu. (You can even automatically  
adjust for daylight savings time.)  
Figure 5-11: Time Setting  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Setup Tab - Basic Setup  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Setup Tab - DDNS  
The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain  
name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or other  
server behind the Router. Before you can use this feature, you need to sign up for DDNS service with a DDNS  
service provider, www.dyndns.org or www.TZO.com. If you do not want to use this feature, keep the default  
setting, Disable.  
DDNS Service  
If your DDNS service is provided by DynDNS.org, then select DynDNS.org from the drop-down menu. If your  
DDNS service is provided by TZO, then select TZO.com. The features available on the DDNS screen will vary,  
depending on which DDNS service provider you use.  
Figure 5-12: Setup Tab - DDNS  
DynDNS.org  
DDNS Service. From this pull-down menu, enter the DDNS service with which you have membership.  
User Name. Enter the User Name for your DDNS account  
Password. Enter the Password for your DDNS account.  
Host Name. The is the DDNS URL assigned by the DDNS service.  
Internet IP Address. This is the Router’s current IP Address as seen on the Internet.  
Status. This displays the status of the DDNS connection.  
Figure 5-13: Setup Tab - DDNS  
TZO.com  
E-mail Address, TZO Password, and Domain Name. Enter the settings of the account you set up with TZO.  
Internet IP Address. The Router’s Internet IP address is displayed here. Because it is dynamic, it will change.  
Status. The status of the DDNS service connection is displayed here.  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Setup Tab - DDNS  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Setup Tab - MAC Address Clone  
A MAC address is a 12-digit code assigned to a unique piece of hardware for identification. Some ISPs will  
require you to register a MAC address in order to access the Internet. If you do not wish to re-register the MAC  
address with your ISP, you may assign the MAC address you have currently registered with your ISP to the Router  
with the MAC Address Clone feature.  
Enable/Disable. To have the MAC Address cloned, click the radio button beside Enable.  
User Defined Entry. Enter the MAC Address registered with your ISP here.  
Clone Your PC’s MAC Address. Clicking this button will clone the MAC address.  
Figure 5-14: Setup Tab - MAC Address Clone  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Setup Tab - MAC Address Clone  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Setup Tab - Advanced Routing  
This tab is used to set up the Router’s advanced functions. Operating Mode allows you to select the type(s) of  
advanced functions you use. Dynamic Routing will automatically adjust how packets travel on your network. Static  
Routing sets up a fixed route to another network destination.  
Operating Mode. Select the mode in which this Router will function. If this Router is hosting your network’s  
connection to the Internet, select Router. If another Router exists on your network, select Bridge. When Bridge is  
chosen, Dynamic Routing will be available as an option.  
Dynamic Routing. This feature enables the Router to automatically adjust to physical changes in the network’s  
layout and exchange routing tables with the other router(s). The Router determines the network packets’ route  
based on the fewest number of hops between the source and the destination. This feature is Disabled by default.  
From the drop-down menu, you can also select LAN & Wireless, which performs dynamic routing over your  
Ethernet and wireless networks. You can also select WAN, which performs dynamic routing with data coming from  
the Internet. Finally, selecting Both enables dynamic routing for both networks, as well as data from the Internet.  
Figure 5-15: Setup Tab - Advanced Routing (Router)  
Static Routing. To set up a static route between the Router and another network, select a number from the Static  
Routing drop-down list. (A static route is a pre-determined pathway that network information must travel to reach a  
specific host or network.) Enter the information described below to set up a new static route. (Click the Delete This  
Entry button to delete a static route.)  
Enter Route Name. Enter a name for the Route here, using a maximum of 25 alphanumeric characters.  
Destination LAN IP. The Destination LAN IP is the address of the remote network or host to which you want to  
assign a static route.  
Subnet Mask. The Subnet Mask determines which portion of a Destination LAN IP address is the network  
portion, and which portion is the host portion.  
Default Gateway. This is the IP address of the gateway device that allows for contact between the Router and  
the remote network or host.  
Interface. This interface tells you whether the Destination IP Address is on the LAN & Wireless (Ethernet and  
wireless networks), the WAN (Internet), or Loopback (a dummy network in which one PC acts like a network—  
necessary for certain software programs).  
Figure 5-16: Setup Tab - Advanced Routing (Bridge)  
Click the Show Routing Table button to view the Static Routes you’ve already set up.  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Setup Tab - Advanced Routing  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Wireless Tab - Basic Wireless Settings  
The basic settings for wireless networking are set on this screen.  
Wireless Network Mode. From this drop-down menu, you can select the wireless standards running on your  
network. If you have both 802.11g and 802.11b devices in your network, keep the default setting, Mixed. If you  
have only 802.11g devices, select G-Only. If you have only 802.11b devices, select B-Only. If you do not have any  
802.11g and 802.11b devices in your network, select Disable.  
Wireless Network Name (SSID). The SSID is the network name shared among all devices in a wireless network.  
The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 9  
characters (use any of the characters on the keyboard). Make sure this setting is the same for all devices in your  
wireless network. For added security, you should change the default SSID (linksys) to a unique name.  
Figure 5-17: Wireless Tab - Basic Wireless Settings  
Wireless Channel. Select the appropriate channel from the list provided to correspond with your network  
settings. All devices in your wireless network must be broadcast on the same channel in order to function  
correctly.  
Wireless SSID Broadcast. When wireless clients survey the local area for wireless networks to associate with,  
they will detect the SSID broadcast by the Router. To broadcast the Router's SSID, keep the default setting,  
Enable. If you do not want to broadcast the Router's SSID, then select Disable.  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Wireless Tab - Basic Wireless Settings  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
IMPORTANT: If you are using WPA, always  
remember that each device in your wireless  
network MUST use the same WPA method  
and shared key, or else the network will not  
function properly.  
The Wireless Tab - Wireless Security  
The Wireless Security settings configure the security of your wireless network. There are four wireless security  
mode options supported by the Router: WPA Personal, WPA Enterprise, WPA2 Personal, WPA2 Enterprise, RADIUS,  
and WEP. (WEP stands for Wired Equivalent Privacy, WPA stands for Wi-Fi Protected Access, which is a security  
standard stronger than WEP encryption. WPA2 is stronger than WPA. WPA Enterprise is WPA used in coordination  
with a RADIUS server. RADIUS stands for Remote Authentication Dial-In User Service.) These are briefly discussed  
here. For detailed instructions on configuring wireless security for the Router, turn to “Appendix B: Wireless  
Security.”  
WPA Personal. WPA gives you two encryption methods, TKIP and AES, with dynamic encryption keys. Select the  
type of algorithm, TKIP or AES. Enter a WPA Shared Key of 8-63 characters. Then enter a Group Key Renewal  
period, which instructs the Router how often it should change the encryption keys.  
Figure 5-18: Wireless Tab - Wireless Security  
(WPA Personal)  
WPA Enterprise. This option features WPA used in coordination with a RADIUS server. (This should only be used  
when a RADIUS server is connected to the Router.) First, select the type of WPA algorithm you want to use, TKIP  
or AES. Enter the RADIUS server’s IP Address and port number, along with a key shared between the Router and  
the server. Last, enter a Key Renewal Timeout, which instructs the Router how often it should change the  
encryption keys.  
Figure 5-19: Wireless Tab - Wireless Security  
(WPA Enterprise)  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Wireless Tab - Wireless Security  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
WPA2 Personal. WPA2 gives you two encryption methods, TKIP and AES, with dynamic encryption keys. Select  
the type of algorithm, AES, or TKIP + AES. Enter a WPA Shared Key of 8-63 characters. Then enter a Group Key  
Renewal period, which instructs the Router how often it should change the encryption keys.  
Figure 5-20: Wireless Tab - Wireless Security  
(WPA2 Personal)  
WPA2 Enterprise. This option features WPA2 used in coordination with a RADIUS server. (This should only be  
used when a RADIUS server is connected to the Router.) First, select the type of WPA algorithm you want to use,  
AES, or TKIP + AES. Enter the RADIUS server’s IP Address and port number, along with a key shared between the  
Router and the server. Last, enter a Key Renewal Timeout, which instructs the Router how often it should change  
the encryption keys.  
Figure 5-21: Wireless Tab - Wireless Security  
(WPA2 Enterprise)  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Wireless Tab - Wireless Security  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
IMPORTANT: If you are using WEP  
encryption, always remember that each  
device in your wireless network MUST use  
the same WEP encryption method and  
encryption key, or else your wireless network  
will not function properly.  
RADIUS. This option features WEP used in coordination with a RADIUS server. (This should only be used when a  
RADIUS server is connected to the Router.) First, enter the RADIUS server’s IP Address and port number, along  
with a key shared between the Router and the server. Then, select a Default Transmit Key (choose which Key to  
use), and a level of WEP encryption, 64 bits 10 hex digits or 128 bits 26 hex digits. Last, either generate a  
WEP key using the Passphrase or enter the WEP key manually.  
Figure 5-22: Wireless Tab - Wireless Security (RADIUS)  
WEP. WEP is a basic encryption method, which is not as secure as WPA. To use WEP, select a Default Transmit Key  
(choose which Key to use), and a level of WEP encryption, 64 bits 10 hex digits or 128 bits 26 hex digits. Then  
either generate a WEP key using the Passphrase or enter the WEP key manually.  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes. For detailed instructions on configuring wireless security for the Router, turn to  
“Appendix B: Wireless Security.”  
Figure 5-23: Wireless Tab - Wireless Security (WEP)  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Wireless Tab - Wireless Security  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Wireless Tab - Wireless MAC Filter  
Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your  
network’s radius.  
Wireless MAC Filter. To filter wireless users by MAC Address, either permitting or blocking access, click Enable.  
If you do not wish to filter users by MAC Address, select Disable.  
Prevent. Clicking this button will block wireless access by MAC Address.  
Permit Only. Clicking this button will allow wireless access by MAC Address.  
Edit MAC Address Filter List. Clicking this button will open the MAC Address Filter List. On this screen, you can  
list users, by MAC Address, to whom you wish to provide or block access. For easy reference, click the Wireless  
Client MAC List button to display a list of network users by MAC Address.  
Figure 5-24: Wireless Tab - Wireless MAC Filter  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
Figure 5-25: MAC Address Filter List  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Wireless Tab - Wireless MAC Filter  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Wireless Tab - Advanced Wireless Settings  
This tab is used to set up the Router’s advanced wireless functions. These settings should only be adjusted by an  
expert administrator as incorrect settings can reduce wireless performance.  
Authentication Type. The default is set to Auto, which allows either Open System or Shared Key authentication  
to be used. With Open System authentication, the sender and the recipient do NOT use a WEP key for  
authentication. With Shared Key authentication, the sender and recipient use a WEP key for authentication.  
Basic Rate. The Basic Rate setting is not actually one rate of transmission but a series of rates at which the  
Router can transmit. The Router will advertise its Basic Rate to the other wireless devices in your network, so  
they know which rates will be used. The Router will also advertise that it will automatically select the best rate  
for transmission. The default setting is Default, when the Router can transmit at all standard wireless rates  
(1-2Mbps, 5.5Mbps, 11Mbps, 18Mbps, and 24Mbps). Other options are 1-2Mbps, for use with older wireless  
technology, and All, when the Router can transmit at all wireless rates. The Basic Rate is not the actual rate of  
data transmission. If you want to specify the Router’s rate of data transmission, configure the Transmission Rate  
setting.  
Figure 5-26: Wireless Tab - Advanced Wireless Settings  
Transmission Rate. The rate of data transmission should be set depending on the speed of your wireless  
network. You can select from a range of transmission speeds, or you can select Auto to have the Router  
automatically use the fastest possible data rate and enable the Auto-Fallback feature. Auto-Fallback will  
negotiate the best possible connection speed between the Router and a wireless client. The default value is Auto.  
CTS Protection Mode. CTS (Clear-To-Send) Protection Mode should remain disabled unless you are having  
severe problems with your Wireless-G products not being able to transmit to the Router in an environment with  
heavy 802.11b traffic. This function boosts the Router’s ability to catch all Wireless-G transmissions but will  
severely decrease performance.  
Beacon Interval. The default value is 100. Enter a value between 1 and 65,535 milliseconds. The Beacon Interval  
value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Router to synchronize  
the wireless network.  
DTIM Interval. This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message  
(DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and  
multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it  
sends the next DTIM with a DTIM Interval value. Its clients hear the beacons and awaken to receive the broadcast  
and multicast messages. The default value is 1.  
Fragmentation Threshold. This value specifies the maximum size for a packet before data is fragmented into  
multiple packets. If you experience a high packet error rate, you may slightly increase the Fragmentation  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Wireless Tab - Advanced Wireless Settings  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Threshold. Setting the Fragmentation Threshold too low may result in poor network performance. Only minor  
reduction of the default value is recommended. In most cases, it should remain at its default value of 2346.  
RTS Threshold. Should you encounter inconsistent data flow, only minor reduction of the default value, 2347, is  
recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will  
not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates  
the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS)  
frame to acknowledge the right to begin transmission. The RTS Threshold value should remain at its default value  
of 2347.  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Wireless Tab - Advanced Wireless Settings  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Security Tab - Firewall  
Firewall Protection. This feature employs Stateful Packet Inspection (SPI) for a more detailed review of data  
packets entering your network environment. Select Enable to use this feature. Select Disable to disable it.  
Block WAN Requests. Enable the Block WAN Request feature by checking the box beside Block Anonymous  
Internet Requests and you can prevent your network from being “pinged,” or detected, by other Internet users.  
The Block WAN Request feature also reinforces your network security by hiding your network ports. Both  
functions of the Block WAN Request feature make it more difficult for outside users to work their way into your  
network. This feature is enabled by default. Select Disabled to allow anonymous Internet requests.  
Filter Multicast. Multicasting allows for multiple transmissions to specific recipients at the same time. If  
multicasting is permitted, then the Router will allow IP multicast packets to be forwarded to the appropriate  
computers. Select Enabled to filter multicasting, or Disabled to disable this feature.  
Figure 5-27: Security Tab - Firewall  
Filter Internet NAT Redirection. This feature uses port forwarding to block access to local servers from local  
networked computers. Select Enabled to filter Internet NAT redirection, or Disabled to disable this feature.  
Filter IDENT (Port 113). This feature keeps port 113 from being scanned by devices outside of your local  
network. Select Enabled to filter port 113, or Disabled to disable this feature.  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
The Security Tab - VPN Passthrough  
Use the settings on this tab to allow VPN tunnels using IPSec, PPTP, or L2TP protocols to pass through the  
Router’s firewall.  
IPSec Pass-through. Internet Protocol Security (IPSec) is a suite of protocols used to implement secure  
exchange of packets at the IP layer. To allow IPSec tunnels to pass through the Router, click Enable. IPSec Pass-  
Through is enabled by default.  
PPTP Pass-through. Point-to-Point Tunneling Protocol (PPTP) allows the Point-to-Point Protocol (PPP) to be  
tunneled through an IP network. To allow PPTP tunnels to pass through the Router, click Enable. PPTP Pass-  
Through is enabled by default.  
Figure 5-28: Security Tab - VPN Passthrough  
L2TP Pass-through. Layer 2 Tunneling Protocol is the method used to enable Point-to-Point sessions via the  
Internet on the Layer 2 level. To allow L2TP tunnels to pass through the Router, click Enable. L2TP Pass-Through  
is enabled by default.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Security Tab - Firewall  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
The Access Restrictions Tab - Internet Access  
The Internet Access screen allows you to block or allow specific kinds of Internet usage and traffic, such as  
Internet access, designated services, websites, and inbound traffic during specific days and times.  
Internet Access Policy. Access can be managed by a policy. Use the settings on this screen to establish an  
access policy (after the Save Settings button is clicked). To delete a policy, select that policy’s number and click  
the Delete button. To view all the policies, click the Summary button. (Policies can be deleted from the Summary  
screen by selecting the policy or policies and clicking the Delete button. To return to the Internet Access tab, click  
the Close button.)  
Status. Policies are disabled by default. To enable a policy, select the policy number from the drop-down menu,  
and click the radio button beside Enable.  
You can create two kinds of policies, one kind to manage Internet access and another kind to manage inbound  
traffic.  
To create an Internet Access policy:  
Figure 5-29: Access Restrictions Tab - Internet Access  
1. Select a number from the Internet Access Policy drop-down menu.  
2. To enable this policy, click the radio button beside Enable.  
3. Enter a Policy Name in the field provided.  
4. Click the Edit List of PCs button to select which PCs will be affected by the policy. The List of PCs screen will  
appear. You can select a PC by MAC Address or IP Address. You can also enter a range of IP Addresses if you  
want this policy to affect a group of PCs. After making your changes, click the Save Settings button to apply  
your changes or Cancel Changes to cancel your changes. Then click the Close button.  
Figure 5-30: Internet Policy Summary  
5. Click the appropriate option, Deny or Allow, depending on whether you want to block or allow Internet access  
for the PCs you listed on the List of PCs screen.  
6. Decide which days and what times you want this policy to be enforced. Select the individual days during  
which the policy will be in effect, or select Everyday. Then enter a range of hours and minutes during which  
the policy will be in effect, or select 24 Hours.  
Figure 5-31: List of PCs  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Access Restrictions Tab - Internet Access  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
7. You can filter access to various services accessed over the Internet, such as FTP or telnet, by selecting  
services from the drop-down menus next to Blocked Services. (You can block up to 20 services.)  
Then enter the range of ports you want to filter.  
If the service you want to block is not listed or you want to edit a service’s settings, then click the Add/Edit  
Service button. Then the Port Services screen will appear.  
To add a service, enter the service’s name in the Service Name field. Select its protocol from the Protocol  
drop-down menu, and enter its range in the Port Range fields. Then click the Add button.  
To modify a service, select it from the list on the right. Change its name, protocol setting, or port range. Then  
click the Modify button.  
Figure 5-32: Port Services  
To delete a service, select it from the list on the right. Then click the Delete button.  
When you are finished making changes on the Port Services screen, click the Apply button to save changes.  
If you want to cancel your changes, click the Cancel button. To close the Port Services screen and return to  
the Access Restrictions screen, click the Close button.  
8. If you want to block websites with specific URL addresses, enter each URL in a separate field next to Website  
Blocking by URL Address.  
9. If you want to block websites using specific keywords, enter each keyword in a separate field next to Website  
Blocking by Keyword.  
10. Click the Save Settings button to save the policy’s settings. To cancel the policy’s settings, click the Cancel  
Changes button.  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Access Restrictions Tab - Internet Access  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Applications and Gaming Tab - Port Range Forward  
The Applications and Gaming Tab allows you to set up public services on your network, such as web servers, ftp  
servers, e-mail servers, or other specialized Internet applications. (Specialized Internet applications are any  
applications that use Internet access to perform functions such as videoconferencing or online gaming. Some  
Internet applications may not require any forwarding.)  
To forward a port, enter the information on each line for the criteria required. The criteria are described here.  
Application. In this field, enter the name you wish to give the application. Each name can be up to 12 characters.  
Start/End. This is the port range. Enter the number that starts the port range under Start and the number that  
ends the range under End.  
Protocol. Enter the protocol used for this application, either TCP or UDP, or Both.  
IP Address. For each application, enter the IP Address of the PC running the specific application.  
Enable. Click the Enable checkbox to enable port forwarding for the relevant application.  
Figure 5-33: Applications and Gaming Tab - Port  
Range Forward  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Applications and Gaming Tab - Port Range Forward  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Applications & Gaming Tab - Port Triggering  
The Port Triggering screen allows the Router to watch outgoing data for specific port numbers. The IP address of  
the computer that sends the matching data is remembered by the Router, so that when the requested data  
returns through the Router, the data is pulled back to the proper computer by way of IP address and port mapping  
rules.  
Port Triggering  
Application. Enter the application name of the trigger.  
Triggered Range  
For each application, list the triggered port number range. Check with the Internet application documentation for  
the port number(s) needed.  
Start Port. Enter the starting port number of the Triggered Range.  
End Port. Enter the ending port number of the Triggered Range.  
Figure 5-34: Applications and Gaming Tab -  
Port Triggering  
Forwarded Range  
For each application, list the forwarded port number range. Check with the Internet application documentation for  
the port number(s) needed.  
Start Port. Enter the starting port number of the Forwarded Range.  
End Port. Enter the ending port number of the Forwarded Range.  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Applications & Gaming Tab - Port Triggering  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Applications and Gaming Tab - DMZ  
The DMZ feature allows one network user to be exposed to the Internet for use of a special-purpose service such  
as Internet gaming or videoconferencing. DMZ hosting forwards all the ports at the same time to one PC. The Port  
Range Forward feature is more secure because it only opens the ports you want to have opened, while DMZ  
hosting opens all the ports of one computer, exposing the computer to the Internet.  
Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static  
IP address assigned to it because its IP address may change when using the DHCP function.  
To expose one PC, select Enable. Then, enter the computer's IP address in the DMZ Host IP Address field.  
Figure 5-35: Applications and Gaming Tab - DMZ  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
The Applications and Gaming Tab - QoS  
Quality of Service (QoS) ensures better service to high-priority types of network traffic, which may involve  
demanding, real-time applications, such as videoconferencing.  
For Wired QoS, there are three priority areas to designate: Device Priority, Ethernet Port Priority and Application  
Priority. For Wireless QoS you can enable or disable WMM Support, No Acknowledgment and APSD Support.  
Wired QoS  
Enable/Disable. To limit outgoing bandwidth for the QoS policies in use, select Enable. Otherwise, select  
Disable.  
Upstream Bandwidth. This setting allows you to limit the outgoing bandwidth for the QoS policies in use, so you  
can control how much bandwidth a particular application is allowed to use. The default value is 0.  
Device Priority  
Enter the name of your network device in the Device name field, enter its MAC Address, then select its priority  
from the drop-down menu.  
Figure 5-36: Applications and Gaming Tab - QOS  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Applications and Gaming Tab - DMZ  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Ethernet Port Priority  
Ethernet Port Priority QoS allows you to prioritize performance for four of the Router’s ports, LAN Ports 1-4. For  
each of these ports, select High or Low for Priority. For Flow Control, if you want the Router to control the  
transmission of data between network devices, select Enable. To disable this feature, select Disable.  
Ethernet Port Priority QoS does not require support from your ISP because the prioritized ports are LAN ports  
going out to your network.  
Application Priority  
You may control your data rate with respect to the application that is consuming bandwidth. Check Optimize  
Gaming Applications to automatically allow common game application ports to have a higher priority. You may  
customize up to eight applications by entering the port number they use.  
Wireless QoS  
WMM Support (WiFi Multimedia). This is available if you are using other devices that are also WMM certified.  
You can enable or disable this feature.  
No Acknowledgment. If this feature is enabled the router will not resend data if an error occurs.  
APSD Support (Automatic Power Save Delivery) Support. This is a power management method that sends  
and receives data at the same rate. You can enable or disable this feature.  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Applications and Gaming Tab - QoS  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Administration Tab - Management  
This section of the Administration tab allows the network’s administrator to manage specific Router functions for  
access and security.  
Local Router Access. You can change the Router’s password from here. Enter a new Router password and then  
type it again in the Re-enter to confirm field to confirm.  
Web Access. HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on  
the World Wide Web. HTTPS - Uses SSL (Secured Socket Layer) to encrypt data transmitted for higher security.  
Select HTTP or HTTPS. Wireless Access Web - If you are using your Wireless Router in a public domain where you  
are giving wireless access to your guests, you can disable wireless access to the router’s web-based utility. You  
will only be able to access the web-based utility via a wired connection if you disable the setting. Select Enable  
to enable wireless access to the Router’s web-based utility or Disable to disable wireless access to the utility.  
Remote Router Access. To access the Router remotely, from outside the network, verify that Enable is selected.  
Then, enter the port number that will be open to outside access. You will need to enter the Router’s password  
when accessing the Router this way, as usual.  
Figure 5-37: Administration Tab - Management  
UPnP. When using UPnP features, select Enable. Because allowing this may present a risk to security, this  
feature is enabled by default.  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
The Administration Tab - Log  
The Router can keep logs of all traffic for your Internet connection. To disable the Log function, keep the default  
setting, Disable. To monitor traffic between the network and the Internet, select Enable. When you wish to view  
the logs, click Incoming Log or Outgoing Log, depending on which you wish to view.  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
Figure 5-38: Administration Tab - Log  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Administration Tab - Management  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Administration Tab - Diagnostics  
The diagnostic tests (Ping and Traceroute) allow you to check the connections of your network components.  
Ping Test. The Ping test will check the status of a connection. Click the Ping button to open the Ping Test screen.  
Enter the address of the PC whose connection you wish to test and how many times you wish to test it. Then,  
click the Ping button. The Ping Test screen will then display the test results. To stop the test, click the Stop  
button. Click the Clear Log button to clear the screen. Click the Close button to return to the Diagnostics screen.  
Traceroute Test. To test the performance of a connect, click the Traceroute button. Enter the address of the PC  
whose connection you wish to test and click the Traceroute button. The Traceroute screen will then display the  
test results. To stop the test, click the Stop button. Click the Clear Log button to clear the screen. Click the Close  
button to return to the Diagnostics screen.  
Figure 5-39: Administration Tab - Diagnostics  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes.  
Figure 5-40: The Ping Test  
Figure 5-41: The Traceroute Test  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Administration Tab - Diagnostics  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Administration Tab - Factory Defaults  
Click the Yes button to reset all configuration settings to their default values, and then click the Save Settings  
button. Any settings you have saved will be lost when the default settings are restored. This feature is disabled by  
default.  
Figure 5-42: Administration Tab - Factory Defaults  
The Administration Tab - Firmware Upgrade  
Firmware can be upgraded by clicking the Upgrade button after browsing for the firmware, which you can  
download from the Linksys website. Do not upgrade your firmware unless you are experiencing problems with  
the Router. For more information about upgrading firmware, refer to “Appendix C: Upgrading Firmware”.  
Figure 5-43: Administration Tab - Firmware Upgrade  
The Administration Tab - Config Management  
This screen is used to back up or restore the Router’s configuration file.  
To back up the Router’s configuration file, click the Backup button. Then follow the on-screen instructions.  
To restore the Router’s configuration file, click the Browse button to locate the file, and follow the on-screen  
instructions. After you have selected the file, click the Restore button.  
Change these settings as described here and click the Save Settings button to apply your changes or Cancel  
Changes to cancel your changes  
Figure 5-44: Administration Tab - Config Management  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Administration Tab - Factory Defaults  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Status Tab - Router  
The Router screen on the Status Tab displays the Router’s current status.  
Firmware Version. This is the Router’s current firmware.  
Current Time. This shows the time, as you set on the Setup Tab.  
MAC Address. This is the Router’s MAC Address, as seen by your ISP.  
Router Name. This is the specific name for the Router, which you set on the Setup Tab.  
Host Name. If required by your ISP, this would have been entered on the Setup Tab.  
Domain Name. If required by your ISP, this would have been entered on the Setup Tab.  
Configuration Type. This shows the information required by your ISP for connection to the Internet. This  
information was entered on the Setup Tab.  
DHCP Release. Available for a DHCP connection, click this button to release the current IP address of the device  
connected to the Router’s Internet port.  
Figure 5-45: Status Tab - Router  
DHCP Renew. Available for a DHCP connection, click this button to replace the current IP address—of the device  
connected to the Router’s Internet port—with a new IP address.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Status Tab - Router  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Status Tab - Local Network  
The Local Network screen on the Status Tab displays the status of your network.  
MAC Address. This is the Router’s MAC Address, as seen on your local, Ethernet network.  
IP Address. This shows the Router’s IP Address, as it appears on your local, Ethernet network.  
Subnet Mask. When the Router is using a Subnet Mask, it is shown here.  
DHCP Server. If you are using the Router as a DHCP server, that will be displayed here.  
Start IP Address. For the range of IP Addresses used by devices on your local, Ethernet network, the beginning  
of that range is shown here.  
Figure 5-46: Status Tab - Local Network  
End IP Address. For the range of IP Addresses used by devices on your local, Ethernet network, the end of that  
range is shown here.  
DHCP Clients Table. Clicking this button will open a screen to show you which PCs are utilizing the Router as a  
DHCP server. You can delete PCs from that list, and sever their connections, by checking a Delete box and  
clicking the Delete button.  
Figure 5-47: DHCP Clients Table  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Status Tab - Local Network  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Status Tab - Wireless  
The Wireless screen on the Status Tab displays the status of your wireless network.  
MAC Address. This is the Router’s MAC Address, as seen on your local, wireless network.  
Mode. As selected from the Wireless tab, this will display the wireless mode (Mixed, G-Only, or Disabled) used by  
the network.  
SSID. As entered on the Wireless tab, this will display the wireless network name or SSID.  
DHCP Server. If you are using the Router as a DHCP server, that will be displayed here.  
Channel. As entered on the Wireless tab, this will display the channel on which your wireless network is  
broadcasting.  
Figure 5-48: Status Tab - Wireless  
Encryption Function. As selected on the Security Tab, this will display what type of encryption the Router uses  
for security.  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Status Tab - Wireless  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The Status Tab - Voice  
The Voice screen on the Status Tab displays the status of your voice connection on your network.  
Firmware Version. This is the Router’s current firmware.  
SIM Status. This is the status of the SIM card.  
Registration Status. This is the status of the registration.  
Call 1/2 Status. This is the status of the phone connection.  
Call Log. Click this button view a log of your calls. The calls are listed by line number, call type, phone number,  
call status, start and end time, and duration. From the drop-down menu, select to view from All Calls, Incoming  
calls, Outgoing calls, and Missed calls. Click Refresh to refresh the screen.  
Error List. If the connection failed, you can click this button to view a list of errors.  
Figure 5-49: Status Tab - Voice  
Figure 5-50: Status Tab - Voice - Call Log  
Figure 5-51: Status Tab - Voice - Error List  
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports  
The Status Tab - Voice  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Appendix A: Troubleshooting  
This appendix consists of two parts: “Common Problems and Solutions” and “Frequently Asked Questions.”  
Provided are possible solutions to problems that may occur during the installation and operation of the Router.  
Read the descriptions below to help you solve your problems. If you can’t find an answer here, check the Linksys  
website at www.linksys.com.  
Common Problems and Solutions  
1. I’m trying to access the Router’s Web-based Utility, but I do not see the login screen. Instead, I see a  
screen saying, “404 Forbidden.”  
If you are using Windows Explorer, perform the following steps until you see the Web-based Utility’s login  
screen (Netscape Navigator will require similar steps):  
1. Click File. Make sure Work Offline is NOT checked.  
2. Press CTRL + F5. This is a hard refresh, which will force Windows Explorer to load new webpages,  
not cached ones.  
3. Click Tools. Click Internet Options. Click the Security tab. Click the Default level button. Make sure  
the security level is Medium or lower. Then click the OK button.  
2. I need to set a static IP address on a PC.  
You can assign a static IP address to a PC by performing the following steps:  
•
For Windows 2000:  
1. Click Start, Settings, and Control Panel. Double-click Network and Dial-Up Connections.  
2. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using, and  
select the Properties option.  
3. In the Components checked are used by this connection box, highlight Internet Protocol (TCP/IP),  
and click the Properties button. Select Use the following IP address option.  
4. Enter a unique IP address that is not used by any other computer on the network connected to the  
Router.  
5. Enter the Subnet Mask, 255.255.255.0.  
6. Enter the Default Gateway, 192.168.0.1 (Router’s default IP address).  
7. Toward the bottom of the window, select Use the following DNS server addresses, and enter the  
Preferred DNS server and Alternative DNS server (provided by your ISP). Contact your ISP or go on its  
website to find the information.  
8. Click the OK button in the Internet Protocol (TCP/IP) Properties window, and click the OK button in the  
Local Area Connection Properties window.  
9. Restart the computer if asked.  
Appendix A: Troubleshooting  
Common Problems and Solutions  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
•
For Windows XP:  
The following instructions assume you are running Windows XP with the default interface. If you are using  
the Classic interface (where the icons and menus look like previous Windows versions), please follow the  
instructions for Windows 2000.  
1. Click Start and Control Panel.  
2. Click the Network and Internet Connections icon and then the Network Connections icon.  
3. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using,  
and select the Properties option.  
4. In the This connection uses the following items box, highlight Internet Protocol (TCP/IP). Click the  
Properties button.  
5. Enter a unique IP address that is not used by any other computer on the network connected to the  
Router.  
6. Enter the Subnet Mask, 255.255.255.0.  
7. Enter the Default Gateway, 192.168.0.1 (Router’s default IP address).  
8. Toward the bottom of the window, select Use the following DNS server addresses, and enter the  
Preferred DNS server and Alternative DNS server (provided by your ISP). Contact your ISP or go on its  
website to find the information.  
9. Click the OK button in the Internet Protocol (TCP/IP) Properties window. Click the OK button in the  
Local Area Connection Properties window.  
•
For Windows Vista:  
1. Click Start and Network.  
2. Click Network and Sharing Center, then select Manage network connections from Tasks.  
3. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using,  
and select the Properties option.  
4. In the This connection uses the following items box, highlight Internet Protocol Version 4 (TCP/  
IPV4). Click the Properties button.  
5. Enter a unique IP address that is not used by any other computer on the network connected to the  
Router.  
6. Enter the Subnet Mask, 255.255.255.0.  
7. Enter the Default Gateway, 192.168.0.1 (Router’s default IP address).  
8. Toward the bottom of the window, select Use the following DNS server addresses, and enter the  
Preferred DNS server and Alternative DNS server (provided by your ISP). Contact your ISP or go on its  
website to find the information.  
9. Click the OK button in the Internet Protocol version 4 (TCP/IPV4) Properties window. Click the OK  
button in the Local Area Connection Properties window.  
3. I want to test my Internet connection.  
Check your TCP/IP settings.  
For Windows 2000, XP and Vista:  
Refer to Windows Help for details. Make sure Obtain IP address automatically is selected in the settings.  
A
•
Appendix A: Troubleshooting  
Common Problems and Solutions  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
B
Open a command prompt.  
For Windows 2000 and XP:  
•
Click Start and Run. In the Open field, type cmd. Press the Enter key or click the OK button. In the  
command prompt, type ping 192.168.0.1 and press the Enter key.  
•
•
If you get a reply, the computer is communicating with the Router.  
If you do NOT get a reply, please check the cable, and make sure Obtain an IP address automatically is  
selected in the TCP/IP settings for your Ethernet adapter.  
For Windows Vista:  
•
Click Start. In the search field, type cmd. Press the Enter key or click the OK button. In the command  
prompt, type ping 192.168.0.1 and press the Enter key.  
•
•
If you get a reply, the computer is communicating with the Router.  
If you do NOT get a reply, please check the cable, and make sure Obtain an IP address automatically is  
selected in the TCP/IP settings for your Ethernet adapter.  
C
In the command prompt, type ping followed by your Internet or WAN IP address and press the Enter key.  
The Internet or WAN IP Address can be found on the Status screen of the Router’s web-based utility. For  
example, if your Internet or WAN IP address is 1.2.3.4, you would enter ping 1.2.3.4 and press the Enter key.  
•
If you get a reply, the computer is connected to the Router.  
•
If you do NOT get a reply, try the ping command from a different computer to verify that your original  
computer is not the cause of the problem.  
D
•
In the command prompt, type ping www.yahoo.com and press the Enter key.  
If you get a reply, the computer is connected to the Internet. If you cannot open a webpage, try the ping  
command from a different computer to verify that your original computer is not the cause of the problem.  
If you do NOT get a reply, there may be a problem with the connection. Try the ping command from a  
different computer to verify that your original computer is not the cause of the problem.  
•
4. I am not getting an IP address on the Internet with my Internet connection.  
•
•
Refer to “Problem #3, I want to test my Internet connection” to verify that you have connectivity.  
If you need to register the MAC address of your Ethernet adapter with your ISP, please see “Appendix E:  
Finding the MAC address and IP Address for Your Ethernet Adapter.” If you need to clone the MAC address  
of your Ethernet adapter onto the Router, see the System section of “Chapter 5: Configuring the  
Wireless-G Broadband Router” for details.  
•
Make sure you are using the right Internet connection settings. Contact your ISP to see if your Internet  
connection type is DHCP, Static IP Address, or PPPoE (commonly used by DSL consumers). Please refer to  
the Setup section of “Chapter 5: Configuring the Wireless-G Broadband Router” for details on Internet  
connection settings.  
•
•
Make sure you have the right cable. Check to see if the Internet column has a solidly lit Link/Act LED.  
Make sure the cable connecting from your cable or DSL modem is connected to the Router’s Internet port.  
Verify that the Status page of the Router’s web-based utility shows a valid IP address from your ISP.  
Turn off the computer, Router, and cable/DSL modem. Wait 30 seconds, and then turn on the Router,  
cable/DSL modem, and computer. Check the Status tab of the Router’s web-based utility to see if you get  
an IP address.  
•
Appendix A: Troubleshooting  
Common Problems and Solutions  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
5. I am not able to access the Setup page of the Router’s web-based utility.  
•
Refer to “Problem #3, I want to test my Internet connection” to verify that your computer is properly  
connected to the Router.  
•
Refer to “Appendix E: Finding the MAC Address and IP address for Your Ethernet Adapter” to verify that  
your computer has an IP Address, Subnet Mask, Gateway, and DNS.  
Set a static IP address on your system; refer to “Problem #2: I need to set a static IP address.”  
Refer to “Problem #10: I am a PPPoE user, and I need to remove the proxy settings or the dial-up pop-up  
window.”  
•
•
6. I need to set up a server behind my Router and make it available to the public.  
To use a server like a web, ftp, or mail server, you need to know the respective port numbers they are using.  
For example, port 80 (HTTP) is used for web; port 21 (FTP) is used for FTP, and port 25 (SMTP outgoing) and  
port 110 (POP3 incoming) are used for the mail server. You can get more information by viewing the  
documentation provided with the server you installed.  
Follow these steps to set up port forwarding through the Router’s web-based utility. We will be setting up  
web, ftp, and mail servers.  
1. Access the Router’s web-based utility by going to http://192.168.0.1 or the IP address of the Router.  
Go to the Applications & Gaming => Port Range Forward tab.  
2. Enter any name you want to use for the Application.  
3. Enter the Start and End Port range of the service you are using. For example, if you have a web server,  
you would enter the range 80 to 80.  
4. Select the protocol(s) you will be using, TCP and/or UDP.  
5. Enter the IP address of the PC or network device that you want the port server to go to. For example,  
if the web server’s Ethernet adapter IP address is 192.168.0.100, you would enter 100 in the field  
provided. Check “Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter” for  
details on getting an IP address.  
6. Check the Enable option for the port services you want to use. Consider the example below:  
Application  
Web server  
Start and End  
80 to 80  
Protocol  
Both  
IP Address  
Enabled  
192.168.0.100  
192.168.0.101  
192.168.0.102  
192.168.0.102  
X
X
X
X
FTP server  
21 to 21  
TCP  
SMTP (outgoing)  
POP3 (incoming)  
25 to 25  
Both  
110 to 110  
Both  
When you have completed the configuration, click the Save Settings button.  
Appendix A: Troubleshooting  
Common Problems and Solutions  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
7. I need to set up online game hosting or use other Internet applications.  
If you want to play online games or use Internet applications, most will work without doing any port  
forwarding or DMZ hosting. There may be cases when you want to host an online game or Internet  
application. This would require you to set up the Router to deliver incoming packets or data to a specific  
computer. This also applies to the Internet applications you are using. The best way to get the information on  
what port services to use is to go to the website of the online game or application you want to use. Follow  
these steps to set up online game hosting or use a certain Internet application:  
1. Access the Router’s web interface by going to http://192.168.0.1 or the IP address of the Router. Go to  
the Applications & Gaming => Port Range Forward tab.  
2. Enter any name you want to use for the Application.  
3. Enter the Start and End Port range of the service you are using. For example, if you want to host  
Unreal Tournament (UT), you would enter the range 7777 to 27900.  
4. Select the protocol(s) you will be using, TCP and/or UDP.  
5. Enter the IP address of the PC or network device that you want the port server to go to. For example,  
if the web server’s Ethernet adapter IP address is 192.168.0.100, you would enter 100 in the field  
provided. Check “Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter” for  
details on getting an IP address.  
6. Check the Enable option for the port services you want to use. Consider the example below:  
Application  
UT  
Start and End  
7777 to 27900  
27015 to 27015  
5631 to 5631  
500 to 500  
Protocol  
Both  
IP Address  
Enabled  
192.168.0.100  
192.168.0.105  
192.168.0.102  
192.168.0.100  
X
X
X
X
Halflife  
Both  
PC Anywhere  
VPN IPSEC  
UDP  
UDP  
When you have completed the configuration, click the Save Settings button.  
8. I can’t get the Internet game, server, or application to work.  
If you are having difficulties getting any Internet game, server, or application to function properly, consider  
exposing one PC to the Internet using DeMilitarized Zone (DMZ) hosting. This option is available when an  
application requires too many ports or when you are not sure which port services to use. Make sure you  
disable all the forwarding entries if you want to successfully use DMZ hosting, since forwarding has priority  
over DMZ hosting. (In other words, data that enters the Router will be checked first by the forwarding  
settings. If the port number that the data enters from does not have port forwarding, then the Router will send  
the data to whichever PC or network device you set for DMZ hosting.)  
Appendix A: Troubleshooting  
Common Problems and Solutions  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Follow these steps to set DMZ hosting:  
1. Access the Router’s web-based utility by going to http://192.168.0.1 or the IP address of the Router.  
Go to the Applications & Gaming => Port Range Forward tab.  
2. Disable or remove the entries you have entered for forwarding. Keep this information in case you  
want to use it at a later time.  
3. Go to the Applications & Gaming => DMZ tab.  
4. Select Enable next to DMZ. In the Client PC IP Address field, enter the IP address of the computer you  
want exposed to the Internet. This will bypass the NAT technology for that computer. Please refer to  
“Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter” for details on getting  
an IP address.  
5. Once completed with the configuration, click the Save Settings button.  
9. I forgot my password, or the password prompt always appears when I am saving settings to the  
Router.  
Reset the Router to factory default by pressing the Reset button for 10 seconds and then releasing it. If you  
are still getting prompted for a password when saving settings, then perform the following steps:  
1. Access the Router’s web-based utility by going to http://192.168.0.1 or the IP address of the Router.  
Enter the default password admin, and click the Administration => Management tab.  
2. Enter a different password in the Router Password field, and enter the same password in the second  
field to confirm the password.  
3. Click the Save Settings button.  
10.I am a PPPoE user, and I need to remove the proxy settings or the dial-up pop-up window.  
If you have proxy settings, you need to disable these on your computer. Because the Router is the gateway for  
the Internet connection, the computer does not need any proxy settings to gain access. Please follow these  
directions to verify that you do not have any proxy settings and that the browser you use is set to connect  
directly to the LAN.  
•
For Microsoft Internet Explorer 5.0 or higher:  
1. Click Start, Settings, and Control Panel. Double-click Internet Options.  
2. Click the Connections tab.  
3. Click the LAN settings button and remove anything that is checked.  
4. Click the OK button to go back to the previous screen.  
5. Click the option Never dial a connection. This will remove any dial-up pop-ups for PPPoE users.  
For Netscape 4.7 or higher:  
•
1. Start Netscape Navigator, and click Edit, Preferences, Advanced, and Proxies.  
2. Make sure you have Direct connection to the Internet selected on this screen.  
3. Close all the windows to finish.  
Appendix A: Troubleshooting  
Common Problems and Solutions  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
11.To start over, I need to set the Router to factory default.  
Hold the Reset button for 10 seconds and then release it. This will return the password, forwarding, and other  
settings on the Router to the factory default settings. In other words, the Router will revert to its original  
factory configuration.  
12.I need to upgrade the firmware.  
In order to upgrade the firmware with the latest features, you need to go to the Linksys website and download  
the latest firmware at www.linksys.com.  
Follow these steps:  
1. Go to the Linksys website at http://www.linksys.com and download the latest firmware.  
2. To upgrade the firmware, follow the steps in “Appendix C: Upgrading Firmware.”  
13.I can’t access my e-mail, web or I am getting corrupted data from the Internet.  
The Maximum Transmission Unit (MTU) setting may need to be adjusted. By default, the MTU is set at 1500.  
For most DSL users, it is strongly recommended to use MTU 1492.  
•
If you are having some difficulties, perform the following steps:  
1. To connect to the Router, go to the web browser, and enter http://192.168.0.1 or the IP address of the  
Router.  
2. Enter the password, if asked. (The default password is admin.)  
3. Look for the MTU option, and select Manual. In the Size field, enter 1492.  
4. Click the Save Settings button to continue.  
If your difficulties continue, change the Size to different values. Try this list of values, one value at a time,  
•
in this order, until your problem is solved:  
1462  
1400  
1362  
1300  
14.When I enter a URL or IP address, I get a time-out error or am prompted to retry.  
•
Check if other PCs work. If they do, ensure that your workstation’s IP settings are correct (IP Address,  
Subnet Mask, Default Gateway, and DNS). Restart the computer that is having a problem.  
If the PCs are configured correctly, but still not working, check the Router. Ensure that it is connected and  
powered on. Connect to it and check its settings. (If you cannot connect to it, check the LAN and power  
connections.)  
•
•
If the Router is configured correctly, check your Internet connection (DSL/cable modem, etc.) to see if it is  
working correctly. You can remove the Router to verify a direct connection.  
•
•
Manually configure the TCP/IP settings with a DNS address provided by your ISP.  
Make sure that your browser is set to connect directly and that any dial-up is disabled. For Internet  
Explorer, click Tools, Internet Options, and then the Connection tab. Make sure that Internet Explorer is  
Appendix A: Troubleshooting  
Common Problems and Solutions  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
set to Never dial a connection. For Netscape Navigator, click Edit, Preferences, Advanced, and Proxy.  
Make sure that Netscape Navigator is set to Direct connection to the Internet.  
Frequently Asked Questions  
What is the maximum number of IP addresses that the Router will support?  
The Router will support up to 253 IP addresses.  
Is IPSec Pass-Through supported by the Router?  
Yes, it is a built-in feature that the Router automatically enables.  
Where is the Router installed on the network?  
In a typical environment, the Router is installed between the cable/DSL modem and the LAN. Plug the Router into  
the cable/DSL modem’s Ethernet port.  
Does the Router support IPX or AppleTalk?  
No. TCP/IP is the only protocol standard for the Internet and has become the global standard for communications.  
IPX, a NetWare communications protocol used only to route messages from one node to another, and AppleTalk, a  
communications protocol used on Apple and Macintosh networks, can be used for LAN to LAN connections, but  
those protocols cannot connect from the Internet to a LAN.  
Does the Internet connection of the Router support 100Mbps Ethernet?  
The Router’s current hardware design supports up to 100Mbps Ethernet on its Internet port; however, the Internet  
connection speed will vary depending on the speed of your broadband connection. The Router also supports  
100Mbps over the auto-sensing Fast Ethernet 10/100 switch on the LAN side of the Router.  
What is Network Address Translation and what is it used for?  
Network Address Translation (NAT) translates multiple IP addresses on the private LAN to one public address that  
is sent out to the Internet. This adds a level of security since the address of a PC connected to the private LAN is  
never transmitted on the Internet. Furthermore, NAT allows the Router to be used with low cost Internet  
accounts, such as DSL or cable modems, when only one TCP/IP address is provided by the ISP. The user may  
have many private addresses behind this single address provided by the ISP.  
Does the Router support any operating system other than Windows 98SE, Windows Millennium,  
Windows 2000, Windows XP or Windows Vista?  
Yes, but Linksys does not, at this time, provide technical support for setup, configuration or troubleshooting of  
any non-Windows operating systems.  
Appendix A: Troubleshooting  
Frequently Asked Questions  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Does the Router support ICQ send file?  
Yes, with the following fix: click ICQ menu -> preference -> connections tab->, and check I am behind a firewall  
or proxy. Then set the firewall time-out to 80 seconds in the firewall setting. The Internet user can then send a file  
to a user behind the Router.  
I set up an Unreal Tournament Server, but others on the LAN cannot join. What do I need to do?  
If you have a dedicated Unreal Tournament server running, you need to create a static IP for each of the LAN  
computers and forward ports 7777, 7778, 7779, 7780, 7781, and 27900 to the IP address of the server. You can  
also use a port forwarding range of 7777 ~ 27900. If you want to use the UT Server Admin, forward another port.  
(Port 8080 usually works well but is used for remote admin. You may have to disable this.) Then in the  
[UWeb.WebServer] section of the server.ini file, set the ListenPort to 8080 (to match the mapped port above) and  
ServerName to the IP assigned to the Router from your ISP.  
Can multiple gamers on the LAN get on one game server and play simultaneously with just one public IP  
address?  
It depends on which network game or what kind of game server you are using. For example, Unreal Tournament  
supports multi-login with one public IP.  
How do I get Half-Life: Team Fortress to work with the Router?  
The default client port for Half-Life is 27005. The computers on your LAN need to have “+clientport 2700x”  
added to the HL shortcut command line; the x would be 6, 7, 8, and on up. This lets multiple computers connect  
to the same server. One problem: Version 1.0.1.6 won’t let multiple computers with the same CD key connect at  
the same time, even if on the same LAN (not a problem with 1.0.1.3). As far as hosting games, the HL server does  
not need to be in the DMZ. Just forward port 27015 to the local IP address of the server computer.  
How can I block corrupted FTP downloads?  
If you are experiencing corrupted files when you download a file with your FTP client, try using another FTP  
program.  
The web page hangs; downloads are corrupt, or nothing but junk characters are being displayed on the  
screen. What do I need to do?  
Force your Ethernet adapter to 10Mbps or half duplex mode, and turn off the “Auto-negotiate” feature of your  
Ethernet adapter as a temporary measure. (Please look at the Network Control Panel in your Ethernet adapter’s  
Advanced Properties tab.) Make sure that your proxy setting is disabled in the browser. Check our website at  
www.linksys.com for more information.  
If all else fails in the installation, what can I do?  
Reset the Router by holding down the reset button until the Power LED fully turns on and off. Reset your cable or  
DSL modem by powering the unit off and then on. Obtain and flash the latest firmware release that is readily  
available on the Linksys website, www.linksys.com.  
Appendix A: Troubleshooting  
Frequently Asked Questions  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
How will I be notified of new Router firmware upgrades?  
All Linksys firmware upgrades are posted on the Linksys website at www.linksys.com, where they can be  
downloaded for free. To upgrade the Router’s firmware, use the Administration - Firmware Upgrade tab of the  
Router’s web-based utility. If the Router’s Internet connection is working well, there is no need to download a  
newer firmware version, unless that version contains new features that you would like to use. Downloading a  
more current version of Router firmware will not enhance the quality or speed of your Internet connection, and  
may disrupt your current connection stability.  
Will the Router function in a Macintosh environment?  
Yes, but the Router’s setup pages are accessible only through Internet Explorer 4.0 or Netscape Navigator 4.0 or  
higher for Macintosh.  
I am not able to get the web configuration screen for the Router. What can I do?  
You may have to remove the proxy settings on your Internet browser, e.g., Netscape Navigator or Internet  
Explorer. Or remove the dial-up settings on your browser. Check with your browser documentation, and make  
sure that your browser is set to connect directly and that any dial-up is disabled. Make sure that your browser is  
set to connect directly and that any dial-up is disabled. For Internet Explorer, click Tools, Internet Options, and  
then the Connection tab. Make sure that Internet Explorer is set to Never dial a connection. For Netscape  
Navigator, click Edit, Preferences, Advanced, and Proxy. Make sure that Netscape Navigator is set to Direct  
connection to the Internet.  
What is DMZ Hosting?  
Demilitarized Zone (DMZ) allows one IP address (computer) to be exposed to the Internet. Some applications  
require multiple TCP/IP ports to be open. It is recommended that you set your computer with a static IP if you  
want to use DMZ Hosting. To get the LAN IP address, see “Appendix E: Finding the MAC Address and IP Address  
for Your Ethernet Adapter.”  
If DMZ Hosting is used, does the exposed user share the public IP with the Router?  
No.  
Does the Router pass PPTP packets or actively route PPTP sessions?  
The Router allows PPTP packets to pass through.  
Is the Router cross-platform compatible?  
Any platform that supports Ethernet and TCP/IP is compatible with the Router.  
How many ports can be simultaneously forwarded?  
Theoretically, the Router can establish 520 sessions at the same time, but you can only forward 10 ranges of  
ports.  
Appendix A: Troubleshooting  
Frequently Asked Questions  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
What are the advanced features of the Router?  
The Router’s advanced features include advanced wireless settings, filters, access restriction policies, port  
forwarding, advanced routing, and DDNS.  
How do I get mIRC to work with the Router?  
Under the Port Forwarding tab, set port forwarding to 113 for the PC on which you are using mIRC.  
Can the Router act as my DHCP server?  
Yes. The Router has DHCP server software built-in.  
Can I run an application from a remote computer over the wireless network?  
This will depend on whether or not the application is designed to be used over a network. Consult the  
application’s documentation to determine if it supports operation over a network.  
What is the IEEE 802.11g standard?  
It is one of the IEEE standards for wireless networks. The 802.11g standard allows wireless networking hardware  
from different manufacturers to communicate, provided that the hardware complies with the 802.11g standard.  
The 802.11g standard states a maximum data transfer rate of 54Mbps and an operating frequency of 2.4GHz.  
What is the IEEE 802.11b standard?  
It is one of the IEEE standards for wireless networks. The 802.11b standard allows wireless networking hardware  
from different manufacturers to communicate, provided that the hardware complies with the 802.11b standard.  
The 802.11b standard states a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.  
What IEEE 802.11g features are supported?  
The product supports the following IEEE 802.11g functions:  
•
•
•
•
•
•
•
CSMA/CA plus Acknowledge protocol  
OFDM protocol  
Multi-Channel Roaming  
Automatic Rate Selection  
RTS/CTS feature  
Fragmentation  
Power Management  
What IEEE 802.11b features are supported?  
The product supports the following IEEE 802.11b functions:  
•
•
•
CSMA/CA plus Acknowledge protocol  
Multi-Channel Roaming  
Automatic Rate Selection  
Appendix A: Troubleshooting  
Frequently Asked Questions  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
•
•
•
RTS/CTS feature  
Fragmentation  
Power Management  
What is ad-hoc mode?  
When a wireless network is set to ad-hoc mode, the wireless-equipped computers are configured to  
communicate directly with each other. The ad-hoc wireless network will not communicate with any wired  
network.  
What is infrastructure mode?  
When a wireless network is set to infrastructure mode, the wireless network is configured to communicate with  
a wired network through a wireless access point.  
What is roaming?  
Roaming is the ability of a portable computer user to communicate continuously while moving freely throughout  
an area greater than that covered by a single access point. Before using the roaming function, the workstation  
must make sure that it is the same channel number with the access point of dedicated coverage area.  
To achieve true seamless connectivity, the wireless LAN must incorporate a number of different functions. Each  
node and access point, for example, must always acknowledge receipt of each message. Each node must  
maintain contact with the wireless network even when not actually transmitting data. Achieving these functions  
simultaneously requires a dynamic RF networking technology that links access points and nodes. In such a  
system, the user’s end node undertakes a search for the best possible access to the system. First, it evaluates  
such factors as signal strength and quality, as well as the message load currently being carried by each access  
point and the distance of each access point to the wired backbone. Based on that information, the node next  
selects the right access point and registers its address. Communications between end node and host computer  
can then be transmitted up and down the backbone.  
As the user moves on, the end node’s RF transmitter regularly checks the system to determine whether it is in  
touch with the original access point or whether it should seek a new one. When a node no longer receives  
acknowledgment from its original access point, it undertakes a new search. Upon finding a new access point, it  
then re-registers, and the communication process continues.  
What is ISM band?  
The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM  
(Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available  
worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in  
the hands of users around the globe.  
Appendix A: Troubleshooting  
Frequently Asked Questions  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
What is Spread Spectrum?  
Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in  
reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for  
reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband  
transmission, but the trade-off produces a signal that is, in effect, louder and thus easier to detect, provided that  
the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to  
the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives,  
Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS).  
What is DSSS? What is FHSS? And what are their differences?  
Frequency-Hopping Spread-Spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that  
is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical  
channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct-Sequence Spread-  
Spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip  
(or chipping code). The longer the chip, the greater the probability that the original data can be recovered. Even if  
one or more bits in the chip are damaged during transmission, statistical techniques embedded in the radio can  
recover the original data without the need for retransmission. To an unintended receiver, DSSS appears as low  
power wideband noise and is rejected (ignored) by most narrowband receivers.  
What is WEP?  
WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 64-bit or 128-bit shared key algorithm, as  
described in the IEEE 802.11 standard.  
What is a MAC Address?  
The Media Access Control (MAC) address is a unique number assigned by the manufacturer to any Ethernet  
networking device, such as a network adapter, that allows the network to identify it at the hardware level. For all  
practical purposes, this number is usually permanent. Unlike IP addresses, which can change every time a  
computer logs onto the network, the MAC address of a device stays the same, making it a valuable identifier for  
the network.  
How do I reset the Router?  
Press the Reset button on the back panel for about five seconds. This will reset the Router to its default settings.  
How do I resolve issues with signal loss?  
There is no way to know the exact range of your wireless network without testing. Every obstacle placed between  
the Router and a wireless PC will create signal loss. Lead glass, metal, concrete floors, water and walls will  
inhibit the signal and reduce range. Start with the Router and your wireless PC in the same room and move it  
away in small increments to determine the maximum range in your environment. You may also try using different  
channels, as this may eliminate interference affecting only one channel.  
Appendix A: Troubleshooting  
Frequently Asked Questions  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
I have excellent signal strength, but I cannot see my network.  
Wireless security is probably enabled on the Router, but not on your wireless adapter (or vice versa). Verify that  
the same wireless security method and passphrase/keys are being used on all devices of your wireless network.  
How many channels/frequencies are available with the Router?  
There are eleven available channels, ranging from 1 to 11, in North America. There may be additional channels  
available in other regions, subject to the regulations of your region and/or country.  
If your questions are not addressed here, refer to the Linksys website, www.linksys.com.  
Appendix A: Troubleshooting  
Frequently Asked Questions  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Appendix B: Wireless Security  
Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of  
Linksys products provide several network security features, but they require specific action on your part for  
implementation. So, keep the following in mind whenever you are setting up or using your wireless network.  
Security Precautions  
The following is a complete list of security precautions to take (at least steps 1 through 5 should be followed):  
1. Change the default SSID.  
2. Disable SSID Broadcast.  
3. Change the default password for the Administrator account.  
4. Enable MAC Address Filtering.  
NOTE: Some of these security features are  
available only through the network router or  
access point. Refer to the router or access  
point’s documentation for more information.  
5. Change the SSID periodically.  
6. Use the highest encryption algorithm possible. Use WPA if it is available. Please note that this may reduce  
your network performance.  
7. Change the WEP encryption keys periodically.  
For information on implementing these security features, refer to “Chapter 5: Configuring the Wireless-G  
Broadband Router.”  
Security Threats Facing Wireless Networks  
Wireless networks are easy to find. Hackers know that in order to join a wireless network, wireless networking  
products first listen for “beacon messages”. These messages can be easily decrypted and contain much of the  
network’s information, such as the network’s SSID (Service Set Identifier). Here are the steps you can take:  
Change the administrator’s password regularly. With every wireless networking device you use, keep in  
mind that network settings (SSID, WEP keys, etc.) are stored in its firmware. Your network administrator is the  
only person who can change network settings. If a hacker gets a hold of the administrator’s password, he, too,  
can change those settings. So, make it harder for a hacker to get that information. Change the administrator’s  
password regularly.  
Appendix B: Wireless Security  
Security Precautions  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
SSID. There are several things to keep in mind about the SSID:  
1. Disable Broadcast  
2. Make it unique  
3. Change it often  
Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be  
more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast  
the SSID.  
Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.)  
Hackers know these defaults and can check these against your network. Change your SSID to something unique  
and not something related to your company or the networking products you use.  
Change your SSID regularly so that any hackers who have gained access to your wireless network will have to  
start from the beginning in trying to break in.  
MAC Addresses. Enable MAC Address filtering. MAC Address filtering will allow you to provide access to only  
those wireless nodes with certain MAC Addresses. This makes it harder for a hacker to access your network with  
a random MAC Address.  
WEP Encryption. Wired Equivalent Privacy (WEP) is often looked upon as a cure-all for wireless security  
concerns. This is overstating WEP’s ability. Again, this can only provide enough security to make a hacker’s job  
more difficult.  
There are several ways that WEP can be maximized:  
1. Use the highest level of encryption possible  
2. Use “Shared Key” authentication  
IMPORTANT: Always remember that each  
device in your wireless network MUST use  
the same encryption method and encryption  
key or your wireless network will not function  
properly.  
3. Change your WEP key regularly  
WPA. Wi-Fi Protected Access (WPA) is the newest and best available standard in Wi-Fi security. Two modes are  
available: Personal (also known as Pre-Shared Key) and Enterprise. Personal gives you a choice of two encryption  
methods: TKIP (Temporal Key Integrity Protocol), which utilizes a stronger encryption method and incorporates  
Message Integrity Code (MIC) to provide protection against hackers, and AES (Advanced Encryption System),  
which utilizes a symmetric 128-Bit block data encryption. Enterprise utilizes a RADIUS (Remote Authentication  
Dial-In User Service) server for authentication and the use of dynamic TKIP, AES, or WEP.  
Appendix B: Wireless Security  
Security Threats Facing Wireless Networks  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
WPA Personal. If you do not have a RADIUS server, Select the type of algorithm, TKIP or AES, enter a  
password in the Pre-Shared key field of 8-64 characters, and enter a Group Key Renewal period time between  
0 and 99,999 seconds, which instructs the Router or other device how often it should change the encryption  
keys.  
WPA Enterprise. WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS  
server is connected to the Router or other device.) First, select the type of WPA algorithm, TKIP or AES. Enter  
the RADIUS server’s IP Address and port number, along with a key shared between the device and the server.  
Last, enter a Group Key Renewal period, which instructs the device how often it should change the encryption  
keys.  
RADIUS. WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS server is  
connected to the Router or other device.) First, enter the RADIUS server’s IP Address and port number, along  
with a key shared between the device and the server. Then, select a WEP key and a level of WEP encryption,  
and either generate a WEP key through the Passphrase or enter the WEP key manually.  
Implementing encryption may have a negative impact on your network’s performance, but if you are transmitting  
sensitive data over your network, encryption should be used.  
These security recommendations should help keep your mind at ease while you are enjoying the most flexible  
and convenient technology Linksys has to offer.  
Appendix B: Wireless Security  
Security Threats Facing Wireless Networks  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Appendix C: Upgrading Firmware  
The Router's firmware is upgraded through the Web-based Utility's Administration tab. Follow these instructions:  
1. Download the firmware from Linksys's website at www.linksys.com.  
2. Extract the firmware file on your computer.  
3. Open the Router’s Web-based Utility, and click the Administration tab.  
4. Click Firmware Upgrade, and the Upgrade Firmware screen will appear.  
5. Enter the location of the firmware's file or click the Browse button to find the file.  
6. Then click the Upgrade button and follow the on-screen instructions.  
Figure C-1: Upgrade Firmware  
Appendix C: Upgrading Firmware  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Appendix D: Windows Help  
Almost Linksys wireless products require Microsoft Windows. Windows is the most used operating system in the  
world and comes with many features that help make networking easier. These features can be accessed through  
Windows Help and are described in this appendix.  
TCP/IP  
Before a computer can communicate with the Router, TCP/IP must be enabled. TCP/IP is a set of instructions, or  
protocol, all PCs follow to communicate over a network. This is true for wireless networks as well. Your PCs will  
not be able to utilize wireless networking without having TCP/IP enabled. Windows Help provides complete  
instructions on enabling TCP/IP.  
Shared Resources  
If you wish to share printers, folder, or files over your network, Windows Help provides complete instructions on  
utilizing shared resources.  
Network Neighborhood/My Network Places  
Other PCs on your network will appear under Network Neighborhood or My Network Places (depending upon the  
version of Windows you're running). Windows Help provides complete instructions on adding PCs to your  
network.  
Appendix D: Windows Help  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Appendix E: Finding the MAC Address and IP Address for  
Your Ethernet Adapter  
This section describes how to find the MAC address for your computer’s Ethernet adapter so you can use the MAC  
filtering and/or MAC address cloning feature of the Router. You can also find the IP address of your computer’s  
Ethernet adapter. This IP address is used for the Router’s filtering, forwarding, and/or DMZ features. Follow the  
steps in this appendix to find the adapter’s MAC or IP address in Windows 2000, XP or Vista.  
Windows 2000 or XP Instructions  
1. Click Start and Run. In the Open field, enter cmd. Press the Enter key or click the OK button.  
2. At the command prompt, enter ipconfig /all. Then press the Enter key.  
Figure E-1: MAC Address/Physical Address  
3. Write down the Physical Address as shown on your computer screen (Figure E-1); it is the MAC address for  
your Ethernet adapter. This appears as a series of numbers and letters.  
The MAC address/Physical Address is what you will use for MAC address cloning or MAC filtering.  
The example in Figure E-1 shows the Ethernet adapter’s IP address as 192.168.0.100. Your computer may  
show something different.  
Note: The MAC address is also called the Physical Address.  
The Wizard is not compatible with Mac® computers. Refer to Chapter 4: Connecting the Wireless-G  
Broadband Router with 2 Phone Ports and Chapter 5: Configuring the Wireless-G Broadband Router  
with 2 Phone Ports.  
Windows Vista Instructions  
1. Click Start. Enter cmd in the Start Search field. Press the Enter key.  
2. At the command prompt, enter ipconfig /all. Then press the Enter key.  
3. Write down the Physical Address as shown on your computer screen (Figure E-1); it is the MAC address for  
your Ethernet adapter. This appears as a series of numbers and letters.  
Figure E-2: MAC Address Filter List  
Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter  
Windows 2000 or XP Instructions  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
The MAC address/Physical Address is what you will use for MAC address cloning or MAC filtering.  
Note: The MAC address is also called the Physical Address.  
The example in Figure E-1 shows the Ethernet adapter’s IP address as 192.168.0.100. Your  
computer may show something different.  
Figure E-3: MAC Address Clone  
For the Router’s Web-based Utility  
For MAC filtering, enter the 12-digit MAC address in this format, XXXXXXXXXXXX, WITHOUT the hyphens. See  
Figure E-2.  
For MAC address cloning, enter the 12-digit MAC address in the MAC Address fields provided, two digits per field.  
See Figure E-3.  
Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter  
For the Router’s Web-based Utility  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Appendix F: Glossary  
802.11b - A wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an  
operating frequency of 2.4GHz.  
802.11g - A wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating  
frequency of 2.4GHz, and backward compatibility with 802.11b devices.  
Access Point - A device that allows wireless-equipped computers and other devices to communicate with a  
wired network. Also used to expand the range of a wireless network.  
Adapter - A device that adds network functionality to your PC.  
Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of  
an access point.  
AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption.  
Backbone - The part of a network that connects most of the systems and networks together, and handles the  
most data.  
Bandwidth - The transmission capacity of a given device or network.  
Beacon Interval - Data transmitted on your wireless network that keeps the network synchronized.  
Bit - A binary digit.  
Boot - To start a device and cause it to start executing instructions.  
Bridge - A device that connects different networks.  
Broadband - An always-on, fast Internet connection.  
Browser - An application program that provides a way to look at and interact with all the information on the  
World Wide Web.  
Buffer - A shared or assigned memory area that is used to support and coordinate different computing and  
networking activities so one isn't held up by the other.  
Byte - A unit of data that is usually eight bits long  
Appendix F: Glossary  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Cable Modem - A device that connects a computer to the cable television network, which in turn connects to the  
Internet.  
CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) - A method of data transfer that is used to prevent  
data collisions.  
CTS (Clear To Send) - A signal sent by a wireless device, signifying that it is ready to receive data.  
Daisy Chain - A method used to connect devices in a series, one after the other.  
Database - A collection of data that is organized so that its contents can easily be accessed, managed, and  
updated.  
DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail server with a  
fixed domain name (e.g., www.xyz.com) and a dynamic IP address.  
Default Gateway - A device that forwards Internet traffic from your local area network.  
DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign  
temporary IP addresses to network computers by “leasing” an IP address to a user for a limited amount of time,  
instead of assigning permanent IP addresses.  
DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be “seen” from  
the Internet.  
DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP  
addresses.  
Domain - A specific name for a network of computers.  
Download - To receive a file transmitted over a network.  
DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines.  
DSSS (Direct-Sequence Spread-Spectrum) - Frequency transmission with a redundant bit pattern resulting in a  
lower probability of information being lost in transit.  
DTIM (Delivery Traffic Indication Message) - A message included in data packets that can increase wireless  
efficiency.  
Dynamic IP Address - A temporary IP address assigned by a DHCP server.  
Appendix F: Glossary  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
EAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access.  
Many specific authentication methods work within this framework.  
EAP-PEAP (Extensible Authentication Protocol-Protected Extensible Authentication Protocol) - A mutual  
authentication method that uses a combination of digital certificates and another system, such as passwords.  
EAP-TLS (Extensible Authentication Protocol-Transport Layer Security) - A mutual authentication method that  
uses digital certificates.  
EasyKeySetup - EasyKeySetup will create a secure wireless connection using encryption. To ensure your T-  
Mobile phone works on your secured connection, follow the EasyKeySetup steps to share the encryption  
information with your phone. If you have not previously enabled security for the wireless router, the default will be  
WPA-PSK encryption. If you have enabled security and have a key already in the wireless router, EasyKeySetup  
will use the currently security settings and share those with the T-Mobile phone.  
Encryption - Encoding data transmitted in a network.  
Ethernet - A networking protocol that specifies how data is placed on and retrieved from a common transmission  
medium.  
Finger - A program that tells you the name associated with an e-mail address.  
Firewall - A set of related programs located at a network gateway server that protects the resources of a  
network from users from other networks.  
Firmware - The programming code that runs a networking device.  
Fragmentation -Breaking a packet into smaller units when transmitting over a network medium that cannot  
support the original size of the packet.  
FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP network.  
Full Duplex - The ability of a networking device to receive and transmit data simultaneously.  
Gateway - A device that interconnects networks with different, incompatible communications protocols.  
Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a  
time.  
Hardware - The physical aspect of computers, telecommunications, and other information technology devices.  
Appendix F: Glossary  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on the World  
Wide Web.  
Infrastructure - A wireless network that is bridged to a wired network via an access point.  
IP (Internet Protocol) - A protocol used to send data over a network.  
IP Address - The address used to identify a computer or device on a network.  
IPCONFIG - A Windows 2000, XP and Vista utility that displays the IP address for a particular networking device.  
IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer.  
ISM band - Radio bandwidth utilized in wireless transmissions.  
ISP (Internet Service Provider) - A company that provides access to the Internet.  
LAN - The computers and networking products that make up your local network.  
LEAP (Lightweight Extensible Authentication Protocol) - A mutual authentication method that uses a username  
and password system.  
MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking  
device.  
Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission.  
mIRC - An Internet Relay Chat program that runs under Windows.  
Multicasting - Sending data to a group of destinations at once.  
NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different  
IP address for the Internet.  
Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or  
transmission between users.  
NNTP (Network News Transfer Protocol) - The protocol used to connect to Usenet groups on the Internet.  
Node - A network junction or connection point, typically a computer or work station.  
Appendix F: Glossary  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
OFDM (Orthogonal Frequency Division Multiplexing) - Frequency transmission that separates the data stream  
into a number of lower-speed data streams, which are then transmitted in parallel to prevent information from  
being lost in transit.  
Packet - A unit of data sent over a network.  
Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically  
generating the WEP encryption keys for Linksys products.  
PEAP (Protected Extensible Authentication Protocol) - A mutual authentication method that uses a combination  
of digital certificates and another system, such as passwords.  
Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online.  
POP3 (Post Office Protocol 3) - A standard mail server commonly used on the Internet.  
Port - The connection point on a computer or networking device used for plugging in cables or adapters.  
Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power.  
PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides authentication  
(username and password) in addition to data transport.  
PPTP (Point-to-Point Tunneling Protocol) - A VPN protocol that allows the Point to Point Protocol (PPP) to be  
tunneled through an IP network. This protocol is also used as a type of broadband connection in Europe.  
Preamble - Part of the wireless signal that synchronizes network traffic.  
RADIUS (Remote Authentication Dial-In User Service) - A protocol that uses an authentication server to control  
network access.  
RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires.  
Roaming - The ability to take a wireless device from one access point's range to another without losing the  
connection.  
Router - A networking device that connects multiple networks together.  
RTS (Request To Send) - A networking method of coordinating large packets through the RTS Threshold setting.  
Server - Any computer whose function in a network is to provide user access to files, printing, communications,  
and other services.  
Appendix F: Glossary  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet.  
SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol.  
Software - Instructions for the computer. A series of instructions that performs a particular task is called a  
“program”.  
SOHO (Small Office/Home Office) - Market segment of professionals who work at home or in small offices.  
SPI (Stateful Packet Inspection) Firewall - A technology that inspects incoming packets of information before  
allowing them to enter the network.  
Spread Spectrum - Wideband radio frequency technique used for more reliable and secure data transmission.  
SSID (Service Set IDentifier) - Your wireless network's name.  
Static IP Address - A fixed address assigned to a computer or device that is connected to a network.  
Static Routing - Forwarding data in a network via a fixed path.  
Subnet Mask - An address code that determines the size of the network.  
Switch - 1. A data switch that connects computing devices to host computers, allowing a large number of  
devices to share a limited number of ports. 2. A device for making, breaking, or changing the connections in an  
electrical circuit.  
TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement  
from the recipient of data sent.  
TCP/IP (Transmission Control Protocol/Internet Protocol) - A set of instructions PCs use to communicate over a  
network.  
Telnet - A user command and TCP/IP protocol used for accessing remote PCs.  
TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that has no directory or password  
capability.  
Throughput - The amount of data moved successfully from one node to another in a given time period.  
TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for  
each packet transmitted.  
Topology - The physical layout of a network.  
Appendix F: Glossary  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
TX Rate - Transmission Rate.  
UDP (User Datagram Protocol) - A network protocol for transmitting data that does not require acknowledgement  
from the recipient of the data that is sent.  
Upgrade - To replace existing software or firmware with a newer version.  
Upload - To transmit a file over a network.  
URL (Uniform Resource Locator) - The address of a file located on the Internet.  
VPN (Virtual Private Network) - A security measure to protect data as it leaves one network and goes to another  
over the Internet.  
WAN (Wide Area Network)- The Internet.  
WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for  
greater security.  
WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with  
each other wirelessly.  
WPA (Wi-Fi Protected Access) - a wireless security protocol using TKIP (Temporal Key Integrity Protocol)  
encryption, which can be used in conjunction with a RADIUS server.  
Appendix F: Glossary  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Appendix G: Specifications  
Model  
WRTU54G-TM  
Standards  
Channels  
Ports  
IEEE 802.3, IEEE 802.3u, IEEE 802.11g, IEEE 802.11b  
11 Channels (US, Canada)  
Internet: One 10/100 RJ-45 Port  
LAN: Four 10/100 RJ-45 Switched Ports  
One Power Port  
Two RJ-11 Phone Ports  
Buttons  
Reset, Get Security Key  
Cabling Type  
LEDs  
Ethernet Network Cable, Standard Phone Cable  
Power, LAN (1-4), WLAN, Phone1-2, Internet, Pairing  
RF Power Output  
UPnP able/cert  
Security Features  
Wireless Security  
18 dBm  
Able  
Stateful Packet Inspection (SPI) Firewall, Internet Policy  
Wi-Fi Protected Access™ (WPA), WEP, Wireless MAC Filtering  
Wi-Fi Protected Access™2 (WPA2)  
Dimensions  
(W x H x D)  
6.69" x 1.30" x 6.97"  
(170 mm x 33 mm x 177 mm)  
Unit Weight  
Power  
13 oz. (368g)  
External, 12V DC, 1.5A  
Appendix G: Specifications  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Certifications  
FCC, IC-03, CE, Wi-Fi (802.11b, 802.11g), WPA, WPA2, WMM  
Operating Temp.  
Storage Temp.  
0ºC to 40ºC (32ºF to 104ºF)  
-20ºC to 70ºC (-4ºF to 158ºF)  
10% to 85%, Non-Condensing  
5% to 90%, Non-Condensing  
Operating Humidity  
Storage Humidity  
Appendix G: Specifications  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Appendix H: Warranty Information  
LIMITED WARRANTY  
Linksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially  
free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under  
this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any  
rebates. This limited warranty extends only to the original purchaser.  
If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return  
Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are  
requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a  
copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You  
are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You  
only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling  
charges.  
ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED  
TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND  
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not  
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives  
You specific legal rights, and You may also have other rights which vary by jurisdiction.  
This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated,  
repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal  
physical or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new  
techniques for intruding upon and attacking networks, Linksys does not warrant that the Product will be free of  
vulnerability to intrusion or attack.  
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR  
PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY  
OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT  
(INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT  
WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if  
any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the  
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.  
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623 USA.  
73  
Appendix H: Warranty Information  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Appendix I: Regulatory Information  
FCC Statement  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device  
may not cause harmful interference, and (2) this device must accept any interference received, including interference that  
may cause undesired operation.  
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the  
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used  
according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee  
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
•
•
•
•
Reorient or relocate the receiving antenna  
Increase the separation between the equipment or devices  
Connect the equipment to an outlet other than the receiver's  
Consult a dealer or an experienced radio/TV technician for assistance  
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the  
user’s authority to operate this equipment.  
FCC Radiation Exposure Statement  
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment  
should be installed and operated with minimum distance 20cm between the radiator and your body.  
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or  
802.11g operation of this product in the USA is firmware-limited to channels 1 through 11.  
Safety Notices  
Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.  
Do not use this product near water, for example, in a wet basement or near a swimming pool.  
Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.  
Appendix I: Regulatory Information  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Industry Canada Statement  
This device complies with Industry Canada ICES-003 and RSS210 rules.  
Operation is subject to the following two conditions:  
1. This device may not cause interference and  
2. This device must accept any interference, including interference that may cause undesired operation of the device.  
This device has been designed to operate with an antenna having a maximum gain of 3dBi. Antenna having a higher  
gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.  
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is  
not more than required for successful communication.  
Industry Canada Radiation Exposure Statement:  
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment  
should be installed and operated with minimum distance 20cm between the radiator & your body.  
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  
Avis d'Industrie Canada  
Cet appareil est conforme aux normes NMB003 et RSS210 d'Industrie Canada.  
L'utilisation de ce dispositif est autorisée seulement aux conditions suivantes :  
1. il ne doit pas produire de brouillage et  
2. il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le  
fonctionnement du dispositif. Le dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximum de 3  
dBi. Les règlements d'Industrie Canada interdisent strictement l'utilisation d'antennes dont le gain est supérieur à  
cette limite. L'impédance requise de l'antenne est de 50 ohms.  
Afin de réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doivent être choisis de  
façon à ce que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne soit pas supérieure au niveau requis pour obtenir  
une communication satisfaisante.  
Avis d'Industrie Canada concernant l'exposition aux radiofréquences :  
Ce matériel est conforme aux limites établies par IC en matière d'exposition aux radiofréquences dans un environnement  
non contrôlé. Ce matériel doit être installé et utilisé à une distance d'au moins 20 cm entre l'antenne et le corps de  
l'utilisateur.  
L'émetteur ne doit pas être placé près d'une autre antenne ou d'un autre émetteur, ou fonctionner avec une autre antenne  
ou un autre émetteur.  
Appendix I: Regulatory Information  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic  
Equipment (WEEE)  
This document contains important information for users with regards to the proper disposal and recycling of Linksys  
products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:  
Appendix I: Regulatory Information  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Appendix I: Regulatory Information  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Appendix I: Regulatory Information  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Appendix I: Regulatory Information  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
For more information, visit www.linksys.com.  
Wireless Disclaimer  
The maximum performance for wireless is derived from IEEE Standard 802.11 specifications. Actual performance can vary,  
including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many  
factors, conditions and variables, including distance from the access point, volume of network traffic, building materials  
and construction, operating system used, mix of wireless products used, interference and other adverse conditions.  
Avis de non-responsabilité concernant les appareils sans fil  
Les performances maximales pour les réseaux sans fil sont tirées des spécifications de la norme IEEE 802.11. Les  
performances réelles peuvent varier, notamment en fonction de la capacité du réseau sans fil, du débit de la transmission  
de données, de la portée et de la couverture. Les performances dépendent de facteurs, conditions et variables multiples,  
en particulier de la distance par rapport au point d’accès, du volume du trafic réseau, des matériaux utilisés dans le  
bâtiment et du type de construction, du système d’exploitation et de la combinaison de produits sans fil utilisés, des  
interférences et de toute autre condition défavorable.  
Appendix I: Regulatory Information  
80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
Appendix J: Software License Agreement  
Software in Linksys Products  
This product from Cisco-Linksys LLC or from one of its affiliates Cisco Systems-Linksys (Asia) Pte Ltd. or Cisco-Linksys  
K.K. (“Linksys”) contains software (including firmware) originating from Linksys and its suppliers and may also contain  
software from the open source community. Any software originating from Linksys and its suppliers is licensed under the  
Linksys Software License Agreement contained at Schedule 1 below. You may also be prompted to review and accept that  
Linksys Software License Agreement upon installation of the software  
Any software from the open source community is licensed under the specific license terms applicable to that software  
made available by Linksys at www.linksys.com/gpl or as provided for in Schedules 2, 3 and 4 below.  
Where such specific license terms entitle you to the source code of such software, that source code is upon request  
available at cost from Linksys for at least three years from the purchase date of this product and may also be available for  
download from www.linksys.com/gpl. For detailed license terms and additional information on open source software in  
Linksys products please look at the Linksys public web site at: www.linksys.com/gpl/ or Schedules 2, 3 or 4 below as  
applicable.  
BY DOWNLOADING OR INSTALLING THE SOFTWARE, OR USING THE PRODUCT CONTAINING THE SOFTWARE, YOU ARE  
CONSENTING TO BE BOUND BY THE SOFTWARE LICENSE AGREEMENTS BELOW. IF YOU DO NOT AGREE TO ALL OF THESE  
TERMS, THEN YOU MAY NOT DOWNLOAD, INSTALL OR USE THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE (OR, IF  
THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND UP TO 30 DAYS  
AFTER ORIGINAL PURCHASE, SUBJECT TO THE RETURN PROCESS AND POLICIES OF THE PARTY FROM WHICH YOU  
PURCHASED SUCH PRODUCT OR SOFTWARE.  
Software Licenses  
The software Licenses applicable to software from Linksys are made available at the Linksys public web site at:  
ww.linksys.com. For your convenience of reference, a copy of the Linksys Software License Agreement and the main  
open source code licenses used by Linksys in its products are contained in the Schedules below.  
Schedule 1 - Linksys Software License Agreement  
THIS LICENSE AGREEMENT IS BETWEEN YOU AND CISCO-LINKSYS LLC OR ONE OF ITS AFFILIATES CISCO SYSTEMS-LINKSYS  
(ASIA) PTE LTD. OR CISCO-LINKSYS K.K. (“LINKSYS”) LICENSING THE SOFTWARE INSTEAD OF CISCO-LINKSYS LLC. BY  
Appendix J: Software License Agreement  
Software in Linksys Products  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
DOWNLOADING OR INSTALLING THE SOFTWARE, OR USING THE PRODUCT CONTAINING THE SOFTWARE, YOU ARE  
CONSENTING TO BE BOUND BY THIS AGREEMENT. IF YOU DO NOT AGREE TO ALL OF THESE TERMS, THEN YOU MAY NOT  
DOWNLOAD, INSTALL OR USE THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED  
AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL PURCHASE,  
SUBJECT TO THE RETURN PROCESS AND POLICIES OF THE PARTY FROM WHICH YOU PURCHASED SUCH PRODUCT OR  
SOFTWARE.  
License. Subject to the terms and conditions of this Agreement, Linksys grants the original end user purchaser of the  
Linksys product containing the Software (“You”) a nonexclusive license to use the Software solely as embedded in or  
(where authorized in the applicable documentation) for communication with such product. This license may not be  
sublicensed, and is not transferable except to a person or entity to which you transfer ownership of the complete Linksys  
product containing the Software, provided you permanently transfer all rights under this Agreement and do not retain any  
full or partial copies of the Software, and the recipient agrees to the terms of this Agreement.  
“Software” includes, and this Agreement will apply to (a) the software of Linksys or its suppliers provided in or with the  
applicable Linksys product, excluding technology from the open source community, and (b) any upgrades, updates, bug  
fixes or modified versions (“Upgrades”) or backup copies of the Software supplied to You by Linksys or an authorized  
reseller, provided you already hold a valid license to the original software and have paid any applicable fee for the Upgrade.  
Protection of Information. The Software and documentation contain trade secrets and/or copyrighted materials of  
Linksys or its suppliers. You will not copy or modify the Software or decompile, decrypt, reverse engineer or disassemble  
the Software (except to the extent expressly permitted by law notwithstanding this provision), and You will not disclose or  
make available such trade secrets or copyrighted material in any form to any third party. Title to and ownership of the  
Software and documentation and any portion thereof, will remain solely with Linksys or its suppliers.  
Collection and Processing of Information. You agree that Linksys and/or its affiliates may, from time to time, collect and  
process information about your Linksys product and/or the Software and/or your use of either in order (i) to enable Linksys  
to offer you Upgrades; (ii) to ensure that your Linksys product and/or the Software is being used in accordance with the  
terms of this Agreement; (iii) to provide improvements to the way Linksys delivers technology to you and to other Linksys  
customers; (iv) to enable Linksys to comply with the terms of any agreements it has with any third parties regarding your  
Linksys product and/or Software and/or (v) to enable Linksys to comply with all applicable laws and/or regulations, or the  
requirements of any regulatory authority or government agency. Linksys and/ or its affiliates may collect and process this  
information provided that it does not identify you personally. Your use of your Linksys product and/or the Software  
constitutes this consent by you to Linksys and/or its affiliates’ collection and use of such information and, for EEA  
customers, to the transfer of such information to a location outside the EEA.  
Software Upgrades etc. If the Software enables you to receive Upgrades, you may elect at any time to receive these  
Upgrades either automatically or manually. If you elect to receive Upgrades manually or you otherwise elect not to receive  
or be notified of any Upgrades, you may expose your Linksys product and/or the Software to serious security threats and/  
or some features within your Linksys product and/or Software may become inaccessible. There may be circumstances  
where we apply an Upgrade automatically in order to comply with changes in legislation, legal or regulatory requirements  
Appendix J: Software License Agreement  
Schedule 1 - Linksys Software License Agreement  
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
or as a result of requirements to comply with the terms of any agreements Linksys has with any third parties regarding  
your Linksys product and/or the Software. You will always be notified of any Upgrades being delivered to you. The terms of  
this license will apply to any such Upgrade unless the Upgrade in question is accompanied by a separate license, in which  
event the terms of that license will apply.  
Open Source Software. The GPL or other open source code incorporated into the Software and the open source license  
for such source code are available for free download at http://www.linksys.com/gpl. If You would like a copy of the GPL  
or other open source code in this Software on a CD, Linksys will mail to You a CD with such code for $9.99 plus the cost of  
shipping, upon request.  
Term and Termination. You may terminate this License at any time by destroying all copies of the Software and  
documentation. Your rights under this License will terminate immediately without notice from Linksys if You fail to comply  
with any provision of this Agreement.  
Limited Warranty. The warranty terms and period specified in the applicable Linksys Product User Guide shall also apply  
to the Software.  
Disclaimer of Liabilities. IN NO EVENT WILL LINKSYS OR ITS SUPPLIERS BE LIABLE FOR ANY LOST DATA, REVENUE OR  
PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF CAUSE  
(INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE, EVEN IF  
LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY EXCEED THE  
AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy under this  
Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or  
consequential damages, so the above limitation or exclusion may not apply to You.  
Export. Software, including technical data, may be subject to U.S. export control laws and regulations and/or export or  
import regulations in other countries. You agree to comply strictly with all such laws and regulations.  
U.S. Government Users. The Software and documentation qualify as “commercial items” as defined at 48 C.F.R. 2.101  
and 48 C.F.R. 12.212. All Government users acquire the Software and documentation with only those rights herein that  
apply to non-governmental customers.  
General Terms. This Agreement will be governed by and construed in accordance with the laws of the State of California,  
without reference to conflict of laws principles. The United Nations Convention on Contracts for the International Sale of  
Goods will not apply. If any portion of this Agreement is found to be void or unenforceable, the remaining provisions will  
remain in full force and effect. This Agreement constitutes the entire agreement between the parties with respect to the  
Software and supersedes any conflicting or additional terms contained in any purchase order or elsewhere.  
Appendix J: Software License Agreement  
Schedule 1 - Linksys Software License Agreement  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
END OF SCHEDULE 1  
Schedule 2  
If this Linksys product contains open source software licensed under Version 2 of the “GNU General Public License” then  
the license terms below in this Schedule 2 will apply to that open source software. The license terms below in this  
Schedule 2 are from the public web site at http://www.gnu.org/copyleft/gpl.html  
GNU GENERAL PUBLIC LICENSE  
Version 2, June 1991  
Copyright © 1989, 1991 Free Software Foundation, Inc.  
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA  
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.  
Preamble  
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU  
General Public License is intended to guarantee your freedom to share and change free software–to make sure the  
software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software  
and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by  
the GNU Lesser General Public License instead.) You can apply it to your programs, too.  
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make  
sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you  
receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs;  
and that you know you can do these things.  
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender  
the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you  
modify it.  
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the  
rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these  
terms so they know their rights.  
Appendix J: Software License Agreement  
Schedule 2  
84  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal  
permission to copy, distribute and/or modify the software.  
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty  
for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what  
they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.  
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a  
free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have  
made it clear that any patent must be licensed for everyone’s free use or not licensed at all.  
The precise terms and conditions for copying, distribution and modification follow.  
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION  
This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be  
distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and  
a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a  
work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another  
language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as  
“you”.  
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The  
act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a  
work based on the Program (independent of having been made by running the Program). Whether that is true depends on  
what the Program does.  
You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that  
you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty;  
keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the  
Program a copy of this License along with the Program.  
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in  
exchange for a fee.  
You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and  
copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these  
conditions:  
Appendix J: Software License Agreement  
Schedule 2  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.  
You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or  
any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.  
If the modified program normally reads commands interactively when run, you must cause it, when started running for  
such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright  
notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute  
the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program  
itself is interactive but does not normally print such an announcement, your work based on the Program is not required to  
print an announcement.)  
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the  
Program, and can be reasonably considered independent and separate works in themselves, then this License, and its  
terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same  
sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of  
this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless  
of who wrote it.  
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the  
intent is to exercise the right to control the distribution of derivative or collective works based on the Program.  
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the  
Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.  
You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under  
the terms of Sections 1 and 2 above provided that you also do one of the following:  
Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms  
of Sections 1 and 2 above on a medium customarily used for software interchange; or,  
Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost  
of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be  
distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,  
Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is  
allowed only for noncommercial distribution and only if you received the program in object code or executable form with  
such an offer, in accord with Subsection b above.)  
Appendix J: Software License Agreement  
Schedule 2  
86  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
The source code for a work means the preferred form of the work for making modifications to it. For an executable work,  
complete source code means all the source code for all modules it contains, plus any associated interface definition files,  
plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source  
code distributed need not include anything that is normally distributed (in either source or binary form) with the major  
components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component  
itself accompanies the executable.  
If distribution of executable or object code is made by offering access to copy from a designated place, then offering  
equivalent access to copy the source code from the same place counts as distribution of the source code, even though  
third parties are not compelled to copy the source along with the object code.  
You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any  
attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your  
rights under this License. However, parties who have received copies, or rights, from you under this License will not have  
their licenses terminated so long as such parties remain in full compliance.  
You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to  
modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this  
License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your  
acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or  
works based on it.  
Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license  
from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not  
impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for  
enforcing compliance by third parties to this License.  
If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent  
issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of  
this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy  
simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may  
not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the  
Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and  
this License would be to refrain entirely from distribution of the Program.  
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section  
is intended to apply and the section as a whole is intended to apply in other circumstances.  
Appendix J: Software License Agreement  
Schedule 2  
87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity  
of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system,  
which is implemented by public license practices. Many people have made generous contributions to the wide range of  
software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to  
decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.  
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.  
If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces,  
the original copyright holder who places the Program under this License may add an explicit geographical distribution  
limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such  
case, this License incorporates the limitation as if written in the body of this License.  
The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time.  
Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or  
concerns.  
Each version is given a distinguishing version number. If the Program specifies a version number of this License which  
applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of  
any later version published by the Free Software Foundation. If the Program does not specify a version number of this  
License, you may choose any version ever published by the Free Software Foundation.  
If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write  
to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free  
Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving  
the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.  
NO WARRANTY  
BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT  
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER  
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,  
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE  
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE  
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.  
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY  
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR  
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR  
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE  
Appendix J: Software License Agreement  
Schedule 2  
88  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER  
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  
END OF TERMS AND CONDITIONS  
END OF SCHEDULE 2  
Schedule 3  
If this Linksys product contains open source software licensed under Version 2.1 of the “GNU Lesser General Public  
License” then the license terms below in this Schedule 3 will apply to that open source software. The license terms below  
in this Schedule 3 are from the public web site at http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html.  
GNU LESSER GENERAL PUBLIC LICENSE  
Version 2.1, February 1999  
Copyright (C) 1991, 1999 Free Software Foundation, Inc.  
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA  
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.  
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License,  
version 2, hence the version number 2.1.]  
Preamble  
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU  
General Public Licenses are intended to guarantee your freedom to share and change free software—to make sure the  
software is free for all its users.  
This license, the Lesser General Public License, applies to some specially designated software packages—typically  
libraries—of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you  
first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any  
particular case, based on the explanations below.  
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to  
make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you  
Appendix J: Software License Agreement  
Schedule 3  
89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
receive source code or can get it if you want it; that you can change the software and use pieces of it in new free  
programs; and that you are informed that you can do these things.  
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to  
surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library  
or if you modify it.  
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights  
that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the  
library, you must provide complete object files to the recipients, so that they can relink them with the library after making  
changes to the library and recompiling it. And you must show them these terms so they know their rights.  
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives  
you legal permission to copy, distribute and/or modify the library.  
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is  
modified by someone else and passed on, the recipients should know that what they have is not the original version, so  
that the original author’s reputation will not be affected by problems that might be introduced by others.  
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a  
company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder.  
Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of  
use specified in this license.  
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU  
Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General  
Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.  
When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally  
speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such  
linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria  
for linking other code with the library.  
We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the  
ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-  
free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries.  
However, the Lesser license provides advantages in certain special circumstances.  
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so  
that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more  
Appendix J: Software License Agreement  
Schedule 3  
90  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by  
limiting the free library to free software only, so we use the Lesser General Public License.  
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a  
large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more  
people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.  
Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a  
program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version  
of the Library.  
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference  
between a “work based on the library” and a “work that uses the library”. The former contains code derived from the  
library, whereas the latter must be combined with the library in order to run.  
GNU LESSER GENERAL PUBLIC LICENSE  
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION  
This License Agreement applies to any software library or other program which contains a notice placed by the copyright  
holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also  
called “this License”). Each licensee is addressed as “you”.  
A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application  
programs (which use some of those functions and data) to form executables.  
The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work  
based on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing  
the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another  
language. (Hereinafter, translation is included without limitation in the term “modification”.)  
“Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete  
source code means all the source code for all modules it contains, plus any associated interface definition files, plus the  
scripts used to control compilation and installation of the library.  
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The  
act of running a program using the Library is not restricted, and output from such a program is covered only if its contents  
constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true  
depends on what the Library does and what the program that uses the Library does.  
Appendix J: Software License Agreement  
Schedule 3  
91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium,  
provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of  
warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of  
this License along with the Library.  
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in  
exchange for a fee.  
You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy  
and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these  
conditions:  
The modified work must itself be a software library.  
You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.  
You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.  
If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses  
the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to  
ensure that, in the event an application does not supply such function or table, the facility still operates, and performs  
whatever part of its purpose remains meaningful.  
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the  
application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be  
optional: if the application does not supply it, the square root function must still compute square roots.)  
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the  
Library, and can be reasonably considered independent and separate works in themselves, then this License, and its  
terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same  
sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this  
License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of  
who wrote it.  
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the  
intent is to exercise the right to control the distribution of derivative or collective works based on the Library.  
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the  
Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.  
You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the  
Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General  
Appendix J: Software License Agreement  
Schedule 3  
92  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public  
License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these  
notices.  
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies  
to all subsequent copies and derivative works made from that copy.  
This option is useful when you wish to copy part of the code of the Library into a program that is not a library.  
You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form  
under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-  
readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used  
for software interchange.  
If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to  
copy the source code from the same place satisfies the requirement to distribute the source code, even though third  
parties are not compelled to copy the source along with the object code.  
A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being  
compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the  
Library, and therefore falls outside the scope of this License.  
However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library  
(because it contains portions of the Library), rather than a “work that uses the library”. The executable is therefore covered  
by this License. Section 6 states terms for distribution of such executables.  
When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the  
work may be a derivative work of the Library even though the source code is not. Whether this is true is especially  
significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is  
not precisely defined by law.  
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small  
inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally  
a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)  
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of  
Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the  
Library itself.  
As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to  
produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the  
Appendix J: Software License Agreement  
Schedule 3  
93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
terms permit modification of the work for the customer’s own use and reverse engineering for debugging such  
modifications.  
You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are  
covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices,  
you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of  
this License. Also, you must do one of these things:  
Accompany the work with the complete corresponding machine-readable source code for the Library including whatever  
changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an  
executable linked with the Library, with the complete machine-readable “work that uses the Library”, as object code and/  
or source code, so that the user can modify the Library and then relink to produce a modified executable containing the  
modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not  
necessarily be able to recompile the application to use the modified definitions.)  
Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time  
a copy of the library already present on the user’s computer system, rather than copying library functions into the  
executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the  
modified version is interface-compatible with the version that the work was made with.  
Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in  
Subsection 6a, above, for a charge no more than the cost of performing this distribution.  
If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the  
above specified materials from the same place.  
Verify that the user has already received a copy of these materials or that you have already sent this user a copy.  
For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed  
for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include  
anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so  
on) of the operating system on which the executable runs, unless that component itself accompanies the executable.  
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally  
accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an  
executable that you distribute.  
You may place library facilities that are a work based on the Library side-by-side in a single library together with other  
library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution  
of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these  
two things:  
Appendix J: Software License Agreement  
Schedule 3  
94  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library  
facilities. This must be distributed under the terms of the Sections above.  
Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining  
where to find the accompanying uncombined form of the same work.  
You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License.  
Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically  
terminate your rights under this License. However, parties who have received copies, or rights, from you under this License  
will not have their licenses terminated so long as such parties remain in full compliance.  
You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to  
modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this  
License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your  
acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or  
works based on it.  
Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license  
from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may  
not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for  
enforcing compliance by third parties with this License.  
If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent  
issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of  
this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy  
simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may  
not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library  
by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this  
License would be to refrain entirely from distribution of the Library.  
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section  
is intended to apply, and the section as a whole is intended to apply in other circumstances.  
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity  
of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system  
which is implemented by public license practices. Many people have made generous contributions to the wide range of  
software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to  
decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.  
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.  
Appendix J: Software License Agreement  
Schedule 3  
95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces,  
the original copyright holder who places the Library under this License may add an explicit geographical distribution  
limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such  
case, this License incorporates the limitation as if written in the body of this License.  
The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to  
time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or  
concerns.  
Each version is given a distinguishing version number. If the Library specifies a version number of this License which  
applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of  
any later version published by the Free Software Foundation. If the Library does not specify a license version number, you  
may choose any version ever published by the Free Software Foundation.  
If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with  
these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write  
to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of  
preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software  
generally.  
NO WARRANTY  
BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT  
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER  
PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,  
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE  
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE  
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.  
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY  
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR  
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR  
INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE  
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER  
SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  
Appendix J: Software License Agreement  
Schedule 3  
96  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
END OF TERMS AND CONDITIONS  
END OF SCHEDULE 3  
Schedule 4  
If this Linksys product contains open source software licensed under the OpenSSL license:  
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.  
(http://www.openssl.org/).  
This product includes cryptographic software written by Eric Young ([email protected]).  
This product includes software written by Tim Hudson ([email protected]).  
In addition, if this Linksys product contains open source software licensed under the OpenSSL license then the license  
terms below in this Schedule 3 will apply to that open source software. The license terms below in this Schedule 3 are  
from the public web site at  
http://www.openssl.org/source/license.html.  
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay  
license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source  
licenses. In case of any license issues related to OpenSSL please contact [email protected].  
OpenSSL License  
Copyright © 1998-2007 The OpenSSL Project. All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following  
conditions are met:  
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.  
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following  
disclaimer in the documentation and/or other materials provided with the distribution.  
All advertising materials mentioning features or use of this software must display the following acknowledgment: “This  
product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”  
The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this  
software without prior written permission. For written permission, please contact [email protected].  
Appendix J: Software License Agreement  
Schedule 4  
97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior  
written permission of the OpenSSL Project.  
Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software  
developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”  
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES,  
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)  
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING  
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGE.  
This product includes cryptographic software written by Eric Young ([email protected]). This product includes software  
written by Tim Hudson ([email protected]).  
Original SSLeay License  
Copyright © 1995-1998 Eric Young ([email protected])All rights reserved.  
This package is an SSL implementation written by Eric Young ([email protected]).  
The implementation was written so as to conform with Netscape’s SSL.  
This library is free for commercial and non-commercial use as long as the following conditions are adhered to. The  
following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL  
code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder  
is Tim Hudson ([email protected]).  
Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed.  
If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used.  
This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the  
package.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following  
conditions are met:  
Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.  
Appendix J: Software License Agreement  
Schedule 4  
98  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Router for 3G/UMTS Broadband  
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following  
disclaimer in the documentation and/or other materials provided with the distribution.  
All advertising materials mentioning features or use of this software must display the following acknowledgement:  
“This product includes cryptographic software written by Eric Young ([email protected])”  
The word ‘cryptographic’ can be left out if the routines from the library being used are not cryptographic related.  
If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must  
include an acknowledgement: “This product includes software written by Tim Hudson ([email protected])”  
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT  
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,  
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE  
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY  
THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)  
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
The license and distribution terms for any publicly available version or derivative of this code cannot be changed. i.e. this  
code cannot simply be copied and put under another distribution license [including the GNU Public License.]  
END OF SCHEDULE 4  
Appendix J: Software License Agreement  
Schedule 4  
99  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless-G Broadband Router with 2 Phone Ports  
Appendix K: Contact Information  
Need to contact Linksys?  
Visit us online for information on the latest products and updates  
to your existing products at:  
http://www.linksys.com or  
ftp.linksys.com  
Can't find information about a product you want to buy  
on the web? Do you want to know more about networking  
with Linksys products? Give our advice line a call at:  
Or fax your request in to:  
800-546-5797 (LINKSYS)  
949-823-3002  
If you experience problems with any Linksys product,  
you can call us at:  
800-326-7114  
Don't wish to call? You can e-mail us at:  
[email protected]  
If any Linksys product proves defective during its warranty period,  
you can call the Linksys Return Merchandise Authorization  
department for obtaining a Return Authorization Number at:  
(Details on Warranty and RMA issues can be found in the Warranty  
Information section in this Guide.)  
949-823-3000  
100  
Appendix K: Contact Information  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Lasko Fan 1646 User Manual
Lasko Fan 4821 User Manual
LG Electronics Air Conditioner PG 100 2006 VER3 User Manual
LG Electronics Speaker System LAP340 User Manual
Lowrance electronic Fish Finder X47 User Manual
Mackie Music Mixer Version 30 User Manual
Makita Vacuum Cleaner 4093D User Manual
Manhattan Computer Products Computer Keyboard 155014 User Manual
Melissa Fan 271 012 User Manual
Metra Electronics Automobile Accessories 99 5824CH User Manual