HomeLink™ Series
Broadband
Network Bridge
Model No.: HPES03
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Linksys HomeLink™ Series
Table of Contents
Introduction
1
1
1
2
The Linksys HomeLink Broadband Network Bridge
Features
Package Contents
Getting to Know the Broadband Network Bridge
Rear Panel Ports
Front Panel LEDs
3
3
4
Using the Broadband Network Bridge
Installation Overview
Connecting Your Devices to the Bridge
Daisy-chaining to a HomeLink Network
Resetting the Broadband Network Bridge
5
5
6
7
8
Troubleshooting
9
Appendix
10
10
11
12
12
13
Twisted Pair Cabling
Telephone Cabling
Specifications
Environmental
Customer Support
Download from Www.Somanuals.com. All Manuals Search And Download.
Broadband Network Bridge
Introduction
The Linksys HomeLink Broadband Network Bridge
Congratulations on the purchase of a Linksys HomeLink Broadband Network
Bridge, the complete Internet connection solution for your Home Phoneline
network. This unique new device features two HomeLink RJ-11 standard tele-
phone ports (configured as one pass-through port), and two 10BaseT Ethernet
ports with one shared uplink port. Plug in your cable modem or DSL
modem’s 10BaseT connection, then attach the bridge to the nearest telephone
jack using standard phone cables, and any computer on your Home Phoneline
network can access the Internet.*
Do you want to share your cable or DSL modem on your 10BaseT network?
You can add a PC at any time by connecting it to the open Ethernet port—or
you can uplink a 10BaseT or 10/100 hub or switch for instant networking.
The groundbreaking technology inside every HomeLink Broadband Network
Bridge delivers intercommunication between home networks of 10Mbps and
1Mbps speeds. With your HomeLink Broadband Network Bridge, that means
instant Internet sharing across both networks at blazing broadband speeds.
High-speed Internet sharing for your home or small office network has never
been easier.*
Features
• Connects Your 10Mbps Ethernet Connection to Your 1Mbps Home
Phoneline Network for Seamless Integration
• Share a Cable or DSL Modem Without Interrupting Normal Telephone
Service*
• Share Internet Access Across Your Entire HomeLink Network—Up to 25
PCs and Even More on an Ethernet Network*
• Stand-alone Unit with Two 10BaseT RJ-45 Ports, one Shared RJ-45 Uplink
Port, and One RJ-11 Modular Telephone Port With Pass-through.
• Fully HomePNA Compliant
• Easy Installation—No Software Required
• Free 24-Hour Technical Support and Limited 1-Year Warranty
*Contact your Internet Service Provider for details.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Linksys HomeLink™ Series
Package Contents
• One HomeLink Broadband Network Bridge (Model No.: HPES03)
• One AC Adapter & Power Cord
• One User Guide and Registration Card
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Broadband Network Bridge
Getting to Know the Broadband
Network Bridge
Rear Panel Ports
Uplink
Share your Internet access over your entire phoneline network
by connecting to your DSL or Cable modem through the
Broadband Bridge's uplink port. The uplink port can also con-
nect to Ethernet devices such as hubs, routers, and switches.
If the uplink port is occupied, the port to its direct right (Port
3) will be inoperable. Any connections made through Port 3
will be lost.
10BaseT
Connect an Ethernet PC (or any other Ethernet device) to
your HomeLink phoneline network through one of the
10BaseT ports. If you plan on using Port 3, the Uplink port
will become unavailable.
HomeLink
Use the HomeLink port to daisy-chain your Broadband
Bridge to your HomeLink network. This port is configured as
a pass-through port, meaning that the network data travels
into the Bridge through one side of the HomeLink port, then
continues out the other. Connect one HomeLink telephone
cable into one side of Port 1, then continue (with another
cable) to your next HomeLink device through the port's other
side. See page 7 of this User Guide for further information.
Power
Connect your power adapter to your Broadband Bridge
through the Power port.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Linksys HomeLink™ Series
Front Panel LEDs
Power
Link
The Power LED is illuminated when the Broadband Bridge is
powered on.
A Link LED will illuminate above a specific port number (1, 2
or 3) if the corresponding port is successfully connected to a
network device.
Activity
An Activity LED will illuminate above a specific port number if
the corresponding port is currently sending or receiving data
over the network.
Collision
A Collision LED will illuminate above a specific port number if
the corresponding port is currently experiencing network colli-
sions. Small amounts of collisions are normal. If you are experi-
encing excessive collisions, verify that your cabling is undam-
aged and properly connected.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Broadband Network Bridge
Using the Broadband Network
Bridge
Note: Power
everything off
before connect-
ing a PC to the
Installation Overview
Broadband
Because the Broadband Network Bridge is a
Network Bridge. If both the
stand-alone device that requires no software or
computer and bridge are
system configuration, setup involves nothing but
plugging everything in and turning everything
on. There are, however, a few limitations to the
amount of physical space your network will be
able to cover without running the risk of data
powered on when the initial
connection is made, the net-
work will act erratically and
you will have to reset the
bridge.
corruption. These restrictions are due to HomePNA and Ethernet standard
limits on the recommended length of your networking cables. (See below.)
Ethernet Cabling
Although there are different grades of Ethernet network cabling, you should
use Category 5 unshielded twisted-pair (UTP) for each Ethernet connection
you make, and no Ethernet cable should exceed 100 meters (328 feet) in
length. Category 5 cabling can be obtained at most computer stores, or you
can crimp your own. (See page 10 for more details.)
Phoneline Cabling
Because of the limitations of standard telephone cables, HomeLink
HomePNA devices require that no network of HomeLink cabling exceeds a
total length of 150 meters (500 feet). In other words, if you have more than
500 feet of telephone wires connecting your network, you will likely experi-
ence data loss.
Beside that, any standard telephone cable will do.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Linksys HomeLink™ Series
Connecting Your Devices to the Bridge
The following steps will have your Broadband Network Bridge up and run-
ning in minutes.
Basic Installation
1. Ensure that every component of your network (including your
Broadband Network Bridge) is powered off.
2. If you are uplinking to a DSL modem, cable modem, Ethernet hub, or
Ethernet switch, connect it to the bridge through the bridge's uplink port
with a network cable. Keep in mind that using the uplink port deactivates
10BaseT Port 3.
3. Connect your Ethernet-equipped devices to the bridge through the
Bridge's 10BaseT ports. If you are not uplinking the Broadband Bridge to
an Ethernet device, both 10BaseT ports 2 and 3 will be available. If you
are using the bridge's uplink port, only port 2 will be active. Ethernet
devices should be connected to the Bridge with a network cable. Each
cable should be less than 100 meters (328 feet) in length.
4. Daisy-chain the Broadband Bridge into the HomeLink network by
running HomeLinked telephone lines through the Bridge's HomeLink
port. The entire length of telephone cable used in a HomeLink network
should never exceed 150 meters (500 feet). For more detailed information
on daisy chaining, see the next page.
5. Power everything on. Connect the supplied power cord to the Power port
on the rear of the bridge, then plug the power cord into an electrical out-
let.
The Broadband Bridge installation is complete.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Broadband Network Bridge
Daisy-chaining to a HomeLink Network
By daisy-chaining your HomeLinked PC's and peripherals, you can create a
simple network that will act in the same way an Ethernet network acts on
your PC's desktop.
While Ethernet networks usually revolve in a star topology around a hub or
switch, phoneline networks link together like a string of Christmas lights. In a
HomeLink network, data passes into on one side of a port, and a new tele-
phone cable continues out from the port’s other side. You can string up to 25
PCs on a single HomeLink network, provided that the entire length of cable
doesn't exceed 150 meters (500 feet).
HomeLink networks are able to send data through existing telephone lines
without interrupting your telephone service, connecting over your existing
telephone jacks. If you have computers on two different floors of your house,
plug one of the downstairs PCs into the phone jack in the wall, and you're
able to network your upstairs computers without running excessive amounts
of extra cable.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Linksys HomeLink™ Series
Resetting the Broadband Network Bridge
If your network connection begins acting erratically, you may want to reset
the bridge. To reset, shut down all of your network components, disconnect
the bridge's power supply, wait five seconds, and then plug it back in.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Broadband Network Bridge
Troubleshooting
Specific Problems
1. I can't get a link at one of my ports.
• Ensure that your cabling is not damaged and that it is connected properly.
• Ensure that the network card you are connecting to has been properly
installed.
• Ensure that both the Bridge and the device are powered on.
• If you are linking to a hub or a switch, ensure that the hub or switch is
functioning correctly.
• If you are connecting to a cable modem, try plugging the cable modem
into the bridge's uplink port rather than a 10BaseT port.
• If all else fails, reset the Bridge.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Linksys HomeLink™ Series
Appendix
Twisted Pair Cabling
There are different grades, or categories,
of twisted-pair cabling. Category 5 is the
most reliable and is highly recommended.
Category 3 is a good second choice.
Straight-through cables are used for con-
necting computers to a hub. Crossover
cables are used for connecting a hub to
another hub (there is an exception: some
hubs have a built-in uplink port that is
crossed internally, which allows you to
link or connect hubs together with a
straight-through cable instead).
You can buy pre-made Category 5 cabling, or cut and crimp your own.
Category 5 cables can be purchased or crimped as either straight-through or
crossover cables. A Category 5 cable has 8 thin, color-coded wires inside that
run from one end of the cable to the other. All 8 wires are used. In a straight-
through cable, wires 1, 2, 3, and 6 at one end of the cable are also wires 1, 2,
3, and 6 at the other end. In a crossover cable, the
order of the wires change from one end to the
other: wire 1 becomes 3, and 2 becomes 6. See the
diagrams on the next page for more detailed infor-
mation on straight-through and crossover cabling.
To determine which wire is wire number 1, hold the cable so
that the end of the plastic RJ-45 tip (the part that goes into a
wall jack first) is facing away from you. Face the clip down
so that the copper side faces up (the springy clip will now be
parallel to the floor).When looking down on the copper side,
wire 1 will be on the far left.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Broadband Network Bridge
Telephone Cabling
The telephone cables you use can be either crossover or straight-through
cables. Standard telephone cables like the ones you use everyday in your
home should do the job.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Linksys HomeLink™ Series
Specifications
Model Number:
Standards:
Protocol:
HPES03
IEEE 802.3 10BaseT, HomePNA v.1.1
CSMA/CD
Ports:
Two 10BaseT RJ-45, One Uplink RJ-45 (Shared),
One Modular Telephone RJ-11 (with Pass-
Through)
Speed:
Cabling Type:
HomePNA - 1Mbps, Ethernet - 10Mbps
Standard Telephone Cable, 10BaseT - Category 3
or 5 UTP or STP
Topology:
LED Status Lights:
Star (10BaseT) or Bus (HomePNA)
Link per Port, Activity per Port, Collision per Port,
Power
Environmental
Dimensions (LxWxH):
Unit Weight:
7.5” x 6” x 2”
0.9 lbs.
Power Input:
5V DC, 3A
Certifications:
Class B, CE Mark Commercial
Operating Temperature: 32°F to 131°F (0°C to 55°C)
Storage Temperature:
Operating Humidity:
Storage Humidity:
-4°F to 158°F
10% to 85% Non-condensing
5% to 90% Non-condensing
(-20°C to 70°C)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Broadband Network Bridge
Customer Support
For help with the installation or operation of your HomeLink Broadband
Network Bridge, contact Linksys Customer Support at one of the phone num-
bers, Internet or e-mail addresses below.
Customer Support
800-326-7114
949-261-1288
Fax
949-261-8868
Email
Web
FTP Site
ftp.linksys.com
13
Download from Www.Somanuals.com. All Manuals Search And Download.
© Copyright 2000 Linksys, All Rights Reserved.
Printed in the USA.
Download from Www.Somanuals.com. All Manuals Search And Download.
|