Linear Satellite Radio DXS 64 User Manual

PRODUCT DESCRIPTION  
FEATURES  
The Model DXS-64 is a battery powered, miniature, water-resistant*, supervised  
transmitter designed for use in emergency applications with Linear’s DX and DXS  
format receivers.The transmitter is supplied with a nylon pendant necklace with a  
breakaway feature for added safety. Pressing the button on the transmitter sends  
a digital coded wireless signal to its companion receiver. To insure sending  
a complete signal, press the transmitter button for a minimum  
of two seconds.  
The DXS-64 transmitter is factory set to a unique code, so no field coding is  
required. The DXS-64 sends a signal when its button is pressed. The transmitter  
can send a signal for up to 30 seconds per activation. The red signal indicator on  
the transmitter lights when the unit is activated.  
DXS-64  
BY  
SNAP  
CORD  
RELEASE  
SUPERVISED  
EMERGENCY  
TRANSMITTER  
NYLON  
NECK  
CORD  
If status transmissions are enabled, they will be sent every two hours. Some  
receivers are able to use these signals, others are not.  
SIGNAL  
INDICATOR  
Every two hours the transmitter tests for a low battery.This test takes place even if  
status transmissions have not been enabled. If the battery tests low, a low battery  
signal is sent and the transmitter LED flashes.  
Operation  
Instructions  
CORD  
LENGTH  
ADJUSTMENT  
Receivers must be programmed to the transmitter’s code before system testing  
and operation. Refer to the receiver’s instructions for details on operation and  
programming.  
ACTIVATION  
BUTTON  
(760) 438-7000  
Each transmitter is sealed to provide water-resistance. The unit’s battery is not  
replaceable. The transmitter should be discarded at the end of its battery life.  
* NOTE:Water resistance not tested by UL  
USA & Canada (800) 421-1587 & (800) 392-0123  
Toll Free FAX (800) 468-1340  
STATUS OPTION & PROGRAMMING  
SYSTEM TESTING  
LINEAR LIMITED WARRANTY  
This Linear product is warranted against defects in material and workmanship for twenty-four (24) months.  
The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale  
customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not  
warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature  
of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear LLC for  
consequential damages arising out of or in connection with use or performance of this product  
or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal,  
installation, or reinstallation. All implied warranties, including implied warranties for merchantability and  
implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This  
Linear LLC Warranty is in lieu of all other warranties express or implied.  
IMPORTANT! TEST SYSTEM WEEKLY  
IF THE TWO HOUR STATUS TIMER IS DESIRED FOR SUPERVISION,  
PERMANENTLY ENABLE THE TIMER BY PRESSING THE TRANSMITTER  
BUTTON FIVE TIMES IN SUCCESSION WITHIN 3 TO 4 SECONDS.  
THE MANUFACTURER STRONGLY RECOMMENDS THAT YOU  
TEST SECURITY EQUIPMENT FREQUENTLY. OVER A PERIOD OF  
TIME, NO ELECTRONIC PRODUCT IS BETTER THAN THE  
INSPECTION AND MAINTENANCE IT RECEIVES. THEREFORE,  
FROM THE TIME OF INSTALLATION, IT IS ABSOLUTELY  
NECESSARY TO TEST THE SYSTEM AT LEAST ONCE A WEEK.  
PLACE THE RECEIVER IN "TEST" MODE  
AND ACTIVATE THE TRANSMITTER.  
VERIFY THAT THE SIGNAL IS RECEIVED  
AND THAT THE SYSTEMS REPORTS AS  
REQUIRED.  
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact  
Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.  
IMPORTANT !!!  
Linear radio controls provide a reliable communications link and fill an important need in portable wireless  
signaling. However, there are some limitations which must be observed.  
/
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as  
Part 15 devices. As such, they have limited transmitter power and therefore limited range.  
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by  
radio signals that occur on or near their operating frequencies, regardless of code settings.  
Changes or modifications to the device may void FCC compliance.  
/
/
/
Infrequently used radio links should be tested regularly to protect against undetected interference or  
fault.  
/
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale  
distributor or dealer, and these facts should be communicated to the ultimate users.  
PROGRAM THE TRANSMITTER INTO THE RECEIVER BY PLACING THE  
RECEIVER INTO PROGRAM MODE. THEN SEND A SIGNAL TO THE RECEIVER  
FROM THE TRANSMITTER. REFER TO THE RECEIVERS PROGRAMMING  
INSTRUCTIONS FOR DETAILS.  
This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the  
following two conditions: (1) This device may not cause harmful interference and (2) this device must  
accept any interference received, including interference that may cause undesired operation.  
Copyright © 2005 Linear LLC  
224801 A  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Kuhn Rikon Mixer 3015 User Manual
La Crosse Technology Clock Radio WT 5360U User Manual
Lightolier Work Light 7226HRM User Manual
Lucent Technologies Life Jacket 555 230 128 User Manual
Makita Cordless Saw UC170D User Manual
Makita Drill DP4010 User Manual
Maytag Oven MEW5627DDB16 User Manual
Melissa Bread Maker 643 043 User Manual
Memorex MP3 Player MD6888 User Manual
MGE UPS Systems Power Supply Comet TM 5 30 kVA User Manual