RETURN TO MAIN MENU
IM10024
July(R2), 2009
MAXsa™ 22 & 29 WIRE DRIVES
For use with machines having Code Numbers:
11615, 11616
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However, your
overall safety can be increased by
proper installation ... and thought-
ful operation on your part. DO
NOT INSTALL, OPERATE OR
REPAIR THIS EQUIPMENT
WITHOUT READING THIS
MANUAL AND THE SAFETY
PRECAUTIONS CONTAINED
THROUGHOUT. And, most
importantly, think before you act
and be careful.
OPERATOR’S MANUAL
Copyright © Lincoln Global Inc.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
ii
SAFETY
ARC RAYS can burn.
ELECTRIC SHOCK can
4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.
kill.
3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-free
gloves to insulate hands.
4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
In addition to the normal safety precautions, if welding
must be performed under electrically hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:
FUMES AND GASES
can be dangerous.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
fumes and gases. When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep
• AC Welder with Reduced Voltage Control.
fumes and gases away from the breathing zone. When
welding with electrodes which require special
ventilation such as stainless or hard facing (see
instructions on container or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and within applicable OSHA PEL and
ACGIH TLV limits using local exhaust or mechanical
ventilation. In confined spaces or in some circum-
stances, outdoors, a respirator may be required.
Additional precautions are also required when welding
on galvanized steel.
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.
3.f. Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
5. b. The operation of welding fume control equipment is affected
by various factors including proper use and positioning of
the equipment, maintenance of the equipment and the spe-
cific welding procedure and application involved. Worker
exposure level should be checked upon installation and
periodically thereafter to be certain it is within applicable
OSHA PEL and ACGIH TLV limits.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.
5.c. Do not weld in locations near chlorinated hydrocarbon vapors
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors to
form phosgene, a highly toxic gas, and other irritating prod-
ucts.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
3.j. Also see Items 6.c. and 8.
5.d. Shielding gases used for arc welding can displace air and
cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.
5.e. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your
employer’s safety practices. MSDS forms are available from
your welding distributor or from the manufacturer.
5.f. Also see item 1.b.
Jan ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
iii
SAFETY
WELDING and CUTTING
CYLINDER may explode
if damaged.
SPARKS can
cause fire or explosion.
7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
6.a. Remove fire hazards from the welding area.
If this is not possible, cover them to prevent
the welding sparks from starting a fire.
process used and properly operating
regulators designed for the gas and
Remember that welding sparks and hot
materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.
pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.
7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.
6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z49.1) and the operating information for the
equipment being used.
7.c. Cylinders should be located:
• Away from areas where they may be struck or subjected to
physical damage.
• A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.
6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact
can cause overheating and create a fire hazard.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even though they have
been “cleaned”. For information, purchase “Recommended
Safe Practices for the Preparation for Welding and Cutting of
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society
(see address above).
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.
7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
6.f. Sparks and spatter are thrown from the welding arc. Wear oil
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.
FOR ELECTRICALLY
powered equipment.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate cir-
cuits. This can create fire hazards or overheat lifting chains
or cables until they fail.
8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s
recommendations.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.
6.h. Also see item 1.c.
6.I. Read and follow NFPA 51B “ Standard for Fire Prevention
During Welding, Cutting and Other Hot Work”, available
from NFPA, 1 Batterymarch Park, PO box 9101, Quincy, Ma
022690-9101.
6.j. Do not use a welding power source for pipe thawing.
Jan ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
iv
SAFETY
5. Toujours porter des lunettes de sécurité dans la zone de
PRÉCAUTIONS DE SÛRETÉ
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où lʼon pique le laitier.
Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv-
antes:
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque dʼincendie dû aux étincelles.
7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque dʼincendie.
Sûreté Pour Soudage A L’Arc
1. Protegez-vous contre la secousse électrique:
a. Les circuits à lʼélectrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.
b. Faire trés attention de bien sʼisoler de la masse quand on
soude dans des endroits humides, ou sur un plancher
metallique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble
de soudage et la machine à souder en bon et sûr état
defonctionnement.
d.Ne jamais plonger le porte-électrode dans lʼeau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode sʼapplicuent aussi au pistolet de
soudage.
8. Sʼassurer que la masse est connectée le plus prés possible
de la zone de travail quʼil est pratique de le faire. Si on place
la masse sur la charpente de la construction ou dʼautres
endroits éloignés de la zone de travail, on augmente le risque
de voir passer le courant de soudage par les chaines de lev-
age, câbles de grue, ou autres circuits. Cela peut provoquer
des risques dʼincendie ou dʼechauffement des chaines et des
câbles jusquʼà ce quʼils se rompent.
9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant
dʼopérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de lʼarc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.
11. Pour obtenir de plus amples renseignements sur la sûreté,
voir le code “Code for safety in welding and cutting” CSA
Standard W 117.2-1974.
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de nʼimporte quelle partie
du corps.
PRÉCAUTIONS DE SÛRETÉ POUR
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR
3. Un coup dʼarc peut être plus sévère quʼun coup de soliel,
donc:
a. Utiliser un bon masque avec un verre filtrant approprié
ainsi quʼun verre blanc afin de se protéger les yeux du ray-
onnement de lʼarc et des projections quand on soude ou
quand on regarde lʼarc.
b. Porter des vêtements convenables afin de protéger la
peau de soudeur et des aides contre le rayonnement de
lʻarc.
c. Protéger lʼautre personnel travaillant à proximité au
soudage à lʼaide dʼécrans appropriés et non-inflammables.
1. Relier à la terre le chassis du poste conformement au code de
lʼélectricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.
2. Autant que possible, Iʼinstallation et lʼentretien du poste seront
effectués par un électricien qualifié.
4. Des gouttes de laitier en fusion sont émises de lʼarc de
soudage. Se protéger avec des vêtements de protection libres
de lʼhuile, tels que les gants en cuir, chemise épaisse, pan-
talons sans revers, et chaussures montantes.
3. Avant de faires des travaux à lʼinterieur de poste, la debranch-
er à lʼinterrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leur
place.
Mar. ʻ93
Download from Www.Somanuals.com. All Manuals Search And Download.
v
v
for selecting a QUALITY product by Lincoln Electric. We want you
to take pride in operating this Lincoln Electric Company product
••• as much pride as we have in bringing this product to you!
Thank You
CUSTOMER ASSISTANCE POLICY
The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip-
ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln
Electric for advice or information about their use of our products. We respond to our customers based on the best information in our posses-
sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor-
mation or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customer’s particular purpose,
with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or
correcting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any
warranty with respect to the sale of our products.
Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control
of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in
applying these types of fabrication methods and service requirements.
for any updated information.
Please Examine Carton and Equipment For Damage Immediately
When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the
time the shipment is received.
Please record your equipment identification information below for future reference. This information can be
found on your machine nameplate.
Product _________________________________________________________________________________
Model Number ___________________________________________________________________________
Code Number or Date Code_________________________________________________________________
Serial Number____________________________________________________________________________
Date Purchased___________________________________________________________________________
Where Purchased_________________________________________________________________________
Whenever you request replacement parts or information on this equipment, always supply the information you
have recorded above. The code number is especially important when identifying the correct replacement parts.
On-Line Product Registration
- Register your machine with Lincoln Electric either via fax or over the Internet.
• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.
• For On-Line Registration: Go to our WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then
“Product Registration”. Please complete the form and submit your registration.
Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:
WARNING
This statement appears where the information must be followed exactly to avoid serious personal injury or loss of life.
CAUTION
This statement appears where the information must be followed to avoid minor personal injury or damage to this equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
vi
TABLE OF CONTENTS
Page
Installation ..........................................................................................................Section A
Product Description .....................................................................................................................A-1
Recommended Processes ..........................................................................................................A-1
Process Limitations .....................................................................................................................A-1
Equipment Limitations .................................................................................................................A-1
Common Equipment....................................................................................................................A-1
General Information.....................................................................................................................A-2
Design Features ...................................................................................................................A-2
Location of Components ......................................................................................................A-2
Specifications ..............................................................................................................................A-3
Safety Precautions. .....................................................................................................................A-4
Non-Safety Standard Equipment..........................................................................................A-4
Input and Ground Connections ............................................................................................A-4
Location and Mounting .........................................................................................................A-4
High Frequency Protection...................................................................................................A-4
®
Power Wave AC/DC1000 SD Systems Connections ................................................................A-5
Mounting Dimensions...........................................................................................................A-5
Connection Diagram.............................................................................................................A-5
Changing Wire Drive Configuration .............................................................................................A-6
Wire Feed Mechanism.................................................................................................................A-7
Gear Ratio Conversion Kits .........................................................................................................A-7
Electrode Connectios ..................................................................................................................A-8
Remote Sense Lead Specifications.............................................................................................A-8
TC-3 Travel Carriage...................................................................................................................A-9
Installation............................................................................................................A-10 thru A12
________________________________________________________________________________
Operation ...........................................................................................................................Section B
Routine operation ........................................................................................................................B-1
Starting Techniques .............................................................................................................B-1
Head Positioning ..................................................................................................................B-2
________________________________________________________________________________
Accessory ...........................................................................................................Section C
Options and Accessories Website ..............................................................................C-1
Motor Conversion Kit For (142:1 NA Style Wire Drives)........................................C-1
Sub-Arc Contact Assemblies....................................................................C2 thru C-8
Vertical Head Adjuster...........................................................................................C-9
Horizontal Head Adjuster.....................................................................................C-10
K129 Tiny TwinArc Kit .........................................................................................C-11
K225 Sub-Arc TwinArc Kit...................................................................................C-13
K281 Solid Wire Straightener for TwinArc...........................................................C-15
________________________________________________________________________________
Maintenance........................................................................................................Section D
Safety Precautions ................................................................................................D-1
Routine and Periodic Engine Maintenance ...........................................................D-1
Calibration Specification........................................................................................D-1
________________________________________________________________________________
Troubleshooting .................................................................................................Section E
Safety Precautions.................................................................................................E-1
How to Use Troubleshooting Guide.......................................................................E-1
Troubleshooting Guide ..........................................................................................E-2
________________________________________________________________________________
Wiring Diagrams and Dimension Print .............................................................Section F
________________________________________________________________________________
Parts List....................................................................................................................P-623
________________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
A-1
A-1
PRODUCT DESCRIPTION
PRODUCT SUMMARY
The MAXsa™ series of Automatic Wire Drives are
designed for hard automation, submerged arc weld-
ing. The heavy-duty gearbox and feed plate have
many years of proven reliability while a new perma-
nent magnet motor has been added.
The MAXsa™ 22 & 29 WIRE DRIVES consist of a
high torque motor and gearbox assembly with a
heavy-duty feed plate housing knurled drive rolls for
positive, accurate wire feeding of heavy welding wire.
Depending on which options are used, the MAXsa™
has many axes of rotation for ease of fixturing and
locating
RECOMMENDED PROCESSES
• The MAXsa™ series of wire drive packages are
best suited for submerged arc welding.
PROCESS LIMITATIONS
• MIG welding
• Robotic applications
EQUIPMENT LIMITATIONS
The MAXsa™ series of wire drives cannot be used
with the NA3, NA-4, or NA-5 series of Lincoln
Automatics.
COMMON EQUIPMENT PACKAGES
Basic Package
• K2803-1
• K2814-1
• K2370-1
Power Wave® AC/DC 1000 SD
MAXsa™ 10 Controller/Feed Head
MAXsa™ 22 Wire Drive
Basic Package with optional kits:
• K2803-1
• K2311-1
• K2312-2
• K2626-2
Power Wave® AC/DC 1000 SD
MAXsa™ Motor Retrofit Kit
MAXsa™ 29 Wire Drive
Wire Drive Controller (for fixture
builders that do not require the
MAXsa™ 10 Controller).
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
A-2
A-2
GENERAL INFORMATION
DESIGN FEATURES - MAXsa™ 22
• Closed-loop speed control.
• Knurled drive rolls.
• Heavy cast aluminum gearbox housing and feed plate assembly.
• Wire straightener.
• Cross Seam Adjuster
• Flux Hopper (not shown)
• Mounting Hardware for accessories
• 32Vdc permanent magnet, high torque motor.
• Conversion kits included to change speed range.
FIGURE A.1 - LOCATION OF MAXsa™ 22 COMPONENTS
Connection
Box
Mounting
Hardware
Cross Seam
Adjuster
Drive Motor
Drive Rolls
Gear Box
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
A-3
A-3
INSTALLATION
DESIGN FEATURES - MAXsa™ 29
• Closed-loop speed control.
• Knurled drive rolls.
• Heavy cast aluminum gearbox housing and feed plate assembly.
• Wire straightener.
• 32Vdc permanent magnet, high torque motor.
• Conversion kits included to change speed range.
FIGURE A.2 - LOCATION OF MAXsa™ 29 COMPONENTS
Connection
Box
Wire Straightener
Mounting
Drive Motor
Drive Rolls
Gear Box
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
A-4
A-4
SPECIFICATIONS
TECHNICAL SPECIFICATIONS - MAXsa™ 22 & 29 WIRE DRIVES
Spec.
Type
142:1 Speed Ratio
95:1 Speed Ratio
57:1 Speed Ratio
Wire Size
Wire Size
Wire Size
Speed
Solid Cored
Speed Solid
Cored
Speed
40-500
Solid
Cored
K2370-2 MAXsa™ 22
K2312-2 MAXsa™ 29
10-200
7/32
5/32
10-300 1/8
5/32
1/16
3/32
Wire Feeders - Input Voltage and Current
Voltage
Input Amperes
32V DC
7 Amps (max.)
PHYSICAL DIMENSIONS
MODEL
WEIGHT
HEIGHT
WIDTH
DEPTH
K2312-2
K2370-2
K2311-1
35.0lbs (15.9kg)
80.0lbs (36.3kg)
10.0lbs (4.5kg)
12.0 in. (305 mm)
14.0in (355mm)
14.0in (355mm)
6.0in (152mm)
10.0in (254mm)
10.0in (254mm)
5.0in (127mm)
8.0 in. (203 mm)
TEMPERATURE RANGES
OPERATING TEMPERATURE RANGE
STORAGE TEMPERATURE RANGE
-40°F to 185°F (-40°C to 85°C)
-4°F to 104°F (-20°C to 40°C)
WELDING PROCESSES
Electrode Diameter Range Output Range (Amperes)
Process
Wire Feed Speed Range
.045” – 7/32" (1.2 – 5.6 mm)
200 - 2000+
SAW
10 - 500 ipm (.25 – 11.43 m/minute)
(with paralleled machines)
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
A-5
A-5
INSTALLATION
SAFETY PRECAUTIONS
Read this entire installation section before you
start installation.
WARNING
ELECTRIC SHOCK can kill.
• Only qualified personnel should per-
form this installation.
• Turn the input power OFF at the dis-
connect switch or fuse box before
working on this equipment. Turn off
the input power to any other equip-
ment connected to the welding sys-
tem at the disconnect switch or fuse
box before working on the equip-
ment.
• Do not touch electrically hot parts.
-------------------------------------------------------------
NON-STANDARD SAFETY INFORMATION
CAUTION
The PF-10S series of wire drives may be at weld-
ing voltage potential when the output of the power
source is active.
------------------------------------------------------------------------
INPUT AND GROUND CONNECTIONS
Only a qualified electrician should connect the
MAXsa™ 22 & 29 WIRE DRIVES. Wire Drive
Installation should be made in accordance with the
appropriate National Electrical Code, all local codes
and the information in this manual.
LOCATION AND MOUNTING
The MAXsa™ Wire Drivewill operate in harsh environ-
ments.
HIGH FREQUENCY PROTECTION
Locate the MAXsa™ Wire Driveaway from radio con-
trolled machinery.
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
A-6
A-6
INSTALLATION
POWER WAVE® AC/DC 1000 SD SUBARC
Mounting Dimensions
SYSTEM CONNECTIONS (See Figure A.3)
Diagram shown is for a single arc system. Refer to the
power source manual for additional connection
options (Multi-arc and/or parallel machines).
The MAXsa™ Wire Drive can be mounted by using
the four 3/8-16 tapped holes or the two 0.562 through
holes. See mounting hole locations (See Figure A.4).
FIGURE A.3 - CONNECTION DIAGRAM
K2803-1
Power Wave® AC/DC 1000
K1543-XX or
K2683-XX
Arclink Cable
K2814-1
MAXsa™ 10
K1795-XX
14-Pin Cable
K2370-2
MAXsa™ 22
67 Lead
Electrode
K231-XX
Weld Cable
Contact Nozzle
K1811-XX
Sense Lead
Work
Weld Cable
Work
FIGURE A.4 - MOUNTING DIMENSIONS
.62
2.50
.41
3/8-16 TAPPED HOLE
(4 PLACES)
.50
4.70
2.69
2.50
4.24
.50
.96
ø.562 (2 HOLES)
7.70
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
A-7
A-7
INSTALLATION
CHANGING THE WIRE DRIVE
CONFIGURATION
5. Carefully disconnect the Motor leads from the har-
ness by pulling the quick-connect terminals apart.
The MAXsa™ 22 & 29 WIRE DRIVES can be recon-
figured to fit in any hard automation application.
6. Reverse the motor leads and reconnect the quick-
connect terminals (see the Wiring Diagram).
As shipped, the MAXsa™ 22 & 29 WIRE DRIVES
Drive Rolls rotate clockwise to feed the wire down.
Reconfiguring the Wire Drive per Figure A.3 may
require reversing the direction of the motor. This is
accomplished by reversing the motor polarity so that
the wire will feed correctly. Follow these instructions to
reverse the motor polarity. See the Wiring Diagram in
Section F of this manual
7. Carefully replace the wire harness back into the
Connection Box and place back onto the Motor
housing locating over the Motor lead grommet.
Ensure that the tachometer leads are completely
covered by the Channel that snaps into the
Connection Box. The Connection Box assembly
should be pushed all the way up to the Motor-to-
Gearbox Adapter Plate.
1. Remove all power from the MAXsa™ Wire Drives.
8. Before securing the Connection Box to the Motor
housing with the Band Strap, ensure that none of
the harness leads are being pinched underneath
the edges of the Connection Box and Channel.
2. Disconnect the Control Cable from the MAXsa™
Wire Drive Connection Box.
3. Loosen the fastener from the Band Strap to the
Connection Box, which secures the assembly to the
Motor housing, and expose the leads inside of the
Connection Box.
9. Place the Band Strap into the "T" slot on the side
of the Connection Box and wrap it around the
Motor housing.
10. Replace the fastener between the Band Strap and
the Connection Box. Tighten so that the Connection
Box cannot move on the Motor housing.
4. Locate the Motor leads that go from the Motor to
the Control Cable connector on the inside of the
Connection Box.
FIGURE A.3
Loosen Socket
Head Screw to Rotate
Motor/Gearbox Assembly
Remove ConnectionBox
to Change Motor Polarity
Loosen Socket
Head Screw to
Rotate Feedplate
Rotate
Rotate
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
A-8
A-8
INSTALLATION
WIRE FEED MECHANISM
4. Pull the gear from the shaft using the screws as a
pulling device.
All MAXsa™ Wire Drive units are shipped with 142:1
ratio gears. Conversion kits are included to change to
either 95:1 or 57:1 ratio depending on wire size to be
used.
5. Be certain woodruff key is properly located on the
shaft. Screw the adapter plate and motor assembly
mounting screws into the new fiber input helical
gear from the stenciled side and place the gear on
the shaft. Replace plain washer, tighten the hex
nut, and remove the adapter plate and motor
assembly mounting screws from the gear.
As shipped, the drive mechanism parts are designed to
feed 3/32 through 7/32(2.4mm - 6.0mm) wire. Other
wire sizes will require different drive rolls and guide
tubes. See table A.1.
6. Support the pinion properly and, with the proper
size punch, drive the roll pin that holds the pinion
out of the shaft. Pull the pinion off. Remove the
Ring Magnet from the pinion gear and snap it onto
the new pinion gear. Before installing the new pin-
ion gear with the Ring Magnet onto the motor shaft,
ensure that the flat washer is located at the bottom
of the shaft. Install the new pinion and replace the
roll pin.
The Idle Roll pressure will need to be adjusted for the
wire being used. The indicator shows two settings -
.035 - 3/32” (0.9 - 2.4mm)
.120.- 7/32” (3.0 - 6.0mm)
The tension adjustment is to be made after loading the
wire into the drive rolls.
NOTE: Lower tension may need to be needed to pre-
vent crushing of some cored wires or softer
alloy solid wires.
7. Cover the teeth of the motor pinion and the input
gear with a non-fluid molydisulfide type grease such
as Non-Fluid Oil Corporationʼs A-29 Special/MS
Lubricant. This grease can be scooped from the
cavity of the gear case.
GEAR RATIO CONVERSION KITS (See
instruction sheet included with the conversion kit
for graphic illustration.)
1. Remove the 2 hex head screws and the 2 slot head
screws holding the Motor to the Wire Drive Gearbox
assembly.
8. Reassemble the motor to the gearbox. Make sure
the gears mesh properly and the adapter plate
locating bead is in its cavity. Replace and tighten
the four screws removed in step 1.
2. Remove existing Adapter Plate and Motor Assembly.
IMPORTANT
3. Take the two long screws removed in step 1 and
screw one into each of the tapped holes located on
the face of fiber input helical gear. Insert the screws
through the full thickness of the gear, and using a
screwdriver wedged between the screws to prevent
rotation, remove the hex nut that holds the gear to
the shaft. Remove plain washer.
See the MAXsa™ 10, or power source manual for
instructions on configuring the system for the
new gear ratio.
TABLE A.1 - DRIVE ROLL KITS
INCLUDED WITH KIT
Incoming
KP1899 DRIVE ROLL KIT
Drive Roll
Drive Roll
Part Number
Outgoing
Guide
Kit Number
Wire Sizes & Types
No. required
Guide
KP1899-1
KP1899-2
KP1899-3
KP1899-4
3/32-7/32”
1/16-3/32”
.035-.052”
.045-.052”
Wires
KP1885-1
KP1886-1
KP1887-1
KP1892-1
2
2
1
2
KP2116-2
KP2116-1
KP1967-1
KP1967-1
KP1963-1
KP2097-2
KP2097-1
KP2097-1
Wires
Solid Wire
Cored Wire
NOTE: Twinarc drive rolls are included with the ATwinarc kits.
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
A-9
A-9
REMOTE SENSE LEAD SPECIFICATIONS
INSTALLATION
ELECTRODE CONNECTIONS
Because the Power Wave® AC/DC 1000 SD can pro-
duce either a DC positive, DC negative or AC output the
electrode and work connections do not need to be
reversed for the different polarities. Additionally no DIP
switch changes are required to switch between the dif-
ferent polarities. All of this is controlled internally by the
Power Wave® AC/DC. The following directions apply to
all polarities:
The MAXsa™ 22 & 29 Wire Drives has an ELEC-
TRODE sense lead extending from the connection
box that is mounted to the motor. This sense lead is
critical to the accuracy of the Power Wave® welding
process. A ring terminal is provided at the end of the
lead. This lead must be extended and connected to
the electrode connection at the nozzle. This connec-
tion should be made as close to the welding arc as
possible. Use at least a 12 AWG wire with a proper
sized ring terminal. Use a screw with a lock washer
and nut to make the connection, then insulate the con-
nection with electrical tape. Proper care should be
taken to protect the sense lead from becoming discon-
nected or damaged. The loss of a sense lead connec-
tion can adversely affect welding performance. The
system may have multiple sense lead configurations
available. Consult the power source manual on how to
configure the power source for the sense leads.
Connect the electrode cable(s) to the "ELECTRODE"
stud(s) on the power source . Connect the other to the
contact assembly at the Wire Drive. Be sure the con-
nection makes tight metal-to-metal electrical contact.
The electrode cable should be sized according to the
specifications given in Table A.1.
NOTE: On the Power Wave® 1000 SD, the Electrode
studs are on the lower left rear corner of the
machine. On older units they are on the lower
left front corner. On those machines, the
cables can be routed through the oval hole in
the cable tray before being connected to the
output terminals.
NOTE: The WORK sense lead (21) for the MAXsa™
22 & 29 Wire Drives system is typically con-
nected at the back of the Power Wave®
AC/DC 1000 SD. If the MAXsa™ wire drive is
to be used in an older system, (PF10A and/or
K2344-X) the WORK sense lead must be
brought out of the motor connection box and
connected to the workpiece.
TABLE A.1 - Output Cable Guidelines
Total Cable Length
ft (m)
Number of
Parallel Cables
Cable Size
Copper
Duty Cycle
Electrode and Work
Combined
4/0 (120 mm2)
3/0 (95 mm2)
0 (0) to 250 (76.2)
0 (0) to 250 (76.2)
2
3
80%
100%
When using inverter type power sources like the
Power Wave®, use the largest welding (electrode and
work) cables that are practical. When using AC appli-
cations the current can reach very high levels. Voltage
drops due to cable resistance can become excessive,
leading to poor welding characteristics if undersized
welding cables are used.
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
A-10
A-10
INSTALLATION
K325 - TC-3 TRAVEL CARRIAGE
The TC-3 travel carriage is available in two models.
Both are “High Capacity” and suitable for multiple arc
welding.
FIGURE A.5
K325HC-S (Standard - 952:1 ratio)
5” to 70”/min (127mm to 1.88M/mim)
19”
(483mm)
K325-HC-F (High Speed - 254:1 ratio)
15” to 270”/min (381mm to 6.86M/min)
NOTE: Although the carriages can be set for speeds
down to zero, speed variations increase dra-
matically with uneven loading when operated
below the recommended minimum speeds.
The maximum amount of equipment that a K325 car-
riage can safely carry is shown in Table A.2
It is important when mounting wire reels,and other
equipment to the TC-3 Travel Carriage that there is a
minimum of overhung weight. The Wire Drive mount-
ings are to be such that the heads are within 19”
(483mm) from the front of the carriage as shown in
Figure A.5.
TABLE A.2 - MAXIMUM EQUIPMENT LOAD FOR TC-3
MULTIPLE ARC OPERATION
TANDEM TWINARC®
Two MAXsa™
Three MAXsa™
Wire Drives and Controls
Three Wire Reels
(60# Coils)
Two MAXsa™
Wire Drives and Controls
Two Wire Reels
(60 # Coils)
Wire Drives and Controls
Four Wire Reels(60# Coils)
Centrally Located
Two K29
Two K29
Three K29
Vertical Adjusters
Two K96
Vertical Adjusters
Three K96
Vertical Adjusters
Two K96
Horizontal Adjusters
Horizontal Adjusters
Horizontal Adjusters
Flux Hopper
Flux Hopper
Flux Hopper
150# of Auxiliary Equipment
Centrally Located over TC-3
No Auxiliary
Equipment
No Auxiliary
Equipment
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
A-11
A-11
INSTALLATION
INSTALLATION
NOTE: To install a MAXsa™ 29 Wire Drive order a
Mounting Bracket (M6769) and the appropri-
ate Head Support (K29 or M8232).
The TC-3 comes factory assembled to fit an 8”
(203mm) beam. See print G1458 for instructions to
use it on 10” (254mm) or 12” (305mm) beams.
5. Use an ohmmeter to be sure that the Wire Reel
shaft and the Wire Drive Mounting Bracket are
electrically isolated from the TC-3 frame.
The Carriage Release Handle, the Wire Reel Support
Bracket and the Wire Drive Support Bracket are not
factory mounted. They should be mounted to the car-
riage before it is placed on the beam per the following
instructions.
With the release handle all the way down, set the car-
riage on the beam. It should run freely along the
beam. With the release handle in the up position the
drive gear should engage the track and hold the car-
riage securley in position.
1. Insert the clutch handle into the hole on the right
side of the carriage so that the end of the handle is
goes into the lift yoke.
If the MAXsa™ 10 Control Box is to be mounted to the
TC-3:
2. Line up the hole in the handle and the hole in the
lift yoke and insert the roll pin that came taped to
the handle. Drive in the roll pin until it is flush with
the yoke.
1. Attach the K2462-1 bracket to the left side of the
carriage per the instructions included with the
bracket.
3. a. If the MAXsa™ 10 Control Box is not going to
be mounted on the carriage, mount the Wire
Reel Support Bracket to the left front corner of
the carriage using the hardware provided.
NOTE: Make certain that there is enough clearance to
the left of the beam to accomodate the K2462-
1 bracket
b. Do not mount the Wire Reel Support if the
K2462-1 Control Box Mounting Bracket for the
MAXsa™ 10 is to be mounted on the carriage.
Another means of mounting the wire must be
used such as a K390 or a user supplied support
for a K299 or K162-1 Spindle Kit (ordered sepa-
rately).
2. Mount the MAXsa™ 10 Control Box to the brack-
et and connect the 4 pin connector from the
Travel Control to the mating receptacle on the
bottom of the MAXsa™ 10 Control Box.
Keep the load on the TC-3 as uniform as practical.
Install cables so that they move smoothly with the car-
riage. Clamp the weld cables to the carriage using the
cable clamp on the left rear corner.
NOTE: Do not mount the K2462-1 Bracket for the
MAXsa™ 10 Control Box until after the car-
riage is placed on the beam.
After all of the equipment has been mounted to the
carriage, the tracking of the drive gear and the bear-
ings should be checked.
4. Install the Wire Drive Mounting Bracket that is sup-
plied with the MAXsa™ 22, using the hardware
and insulators provided. See Figure A.6.
FIGURE A.6 - WIRE DRIVE MOUNTING
Wire Reel
Mounting Bracket
MAXsa™ 10
Mounting Bracket
(K2462-1)
Clutch
Handle
Wire Drive Mounting
Bracket (M6769)
Head Support
(M8232)
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
A-12
A-12
INSTALLATION
INCLINED OPERATION OF TC-3
1. The beam should have a Knurled Drive Flange and
the TC-3 should have the straight toothed Drive
Gear (T13586 - ordered separately).
CAUTION
When the carriage is used in an inclined application
the unit is free to move whenever the Carriage
Release Handle is pulled down. This may happen
even if a counter balance weight is used. With a prop-
er counterbalance and if the flux hopper and wire
reel(s) are mounted off of the carriage, this “free-
wheeling” is less likely to occur since the changing
weight will not affect the counterbalance.
2. With a tilt of 5° or less, a counterbalance is typical-
ly not required (see CAUTION).
3. A tilt in excess of 5° will require a counter weight
as shown in Figure A.10. The amount of coun-
teweight will depend on the tilt angle and the
amount of load on the carriage. Beam angles
should be limited to 10° or less.
FIGURE A.10 - INCLINED OPERATION
Pulley
Carriage
Beam
Weight
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
A-13
A-13
INSTALLATION
FIGURE A.7 - DRIVE GEAR TRACKING
Incorrect
ADD Shims
Shims
Full Face
Contact
.88”
Incorrect
REMOVE Shims
Beam
Drive Rail
Drive Gear
DRIVE GEAR TRACKING
FIGURE A.8 - BEARING TRACKING
The TC-3 is shimmed at the factory so that the drive
gear sits flat against a .88” (22mm) flange when the
release handle is in the up position. If the flange
dimension is other than .88” (22mm) the shims under
the TC-3 gear box mounting will have to be changed
accordingly. See Figure A.7.
CORRECT PATTERN
Full Face Bearing
Contact
INCORRECT PATTERNS
Bearing is not flat
Against Drive Rail
NOTE: TC-3 units are shipped with a helical tooth
drive wheel that is suitable for use on a
smooth drive rail. A straight tooth gear
(T13586) is available for use on a drive rail
with a straight cut knurl.
FIGURE A.9 BEARING SHIMS
CARRIAGE BEARING TRACKING
Bearing tracking can be checked by placing a strip of
white paper over the area where the bearings ride.
With the drive gear disengaged (handle down), move
the carriage over the strips. If the tracking is correct
the bearings will leave a uniform trace on the paper.
See Figure A.8. If traces are not corrrect add shims as
necessary. See Figure A.9.
Shim Here
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
B-1
B-1
OPERATION
ROUTINE OPERATION
2. On-the-fly Starting - refers to starting the weld
after the travel begins to get a “scratch” start.
Normally this type of starting requires the use of a
ʻrun-onʼ tab to insure proper weld deposition at the
beginning of the weld.
Once the procedures and parameters are properly set
at the controller the operator should be able to make
production welds without changing those settings. A
typical weld sequence is as follows:
1. Before starting, make sure that:
a. Use the Set-Up Menue of the MAXsa™ 10
to set the travel to start with the START
button.
a. There is enough wire on the reel(s) to finish
the weld.
b. Follow the Hot Starting procedure.
b. The flux hopper is filled with new or proper-
ly screened flux.
Cold Starting - refers to starting the weld with the
Wire Drive Head stationary and the electrode touching
the work.
2. Energize the power source and wait for it to stabi-
lize (all Status LEDʼs Green).
a. This procedure is not recommended for the
Power Wave® AC/DC 1000 / MAXsa™ 22
& 29 WIRE DRIVES combinations but may
work OK with smaller diameter wires and
proper setting of the Start parameters.
3. Position the Wire Feed Head at the start of the
weld. Be sure the TC-3 Carriage or travel mecha-
nism is set to move in the proper direction
4. Set the travel switch for “Automatic Travel” if the
“Hand Travel” position was used to position the
feed head in Step 3.
b. Follow Hot Starting procedure but omit
“step c”.
STARTING TECHNIQUES
HEAD POSITION ADJUSTMENTS
1. Hot Starting - refers to starting the weld with the
Wire Drive head stationary and the wire not touch-
ing the workpiece.
The MAXsa™ 22 & 29 WIRE DRIVES can be easily
adjusted to any weld position. The most often used
adjustments are available on both the MAXsa™ 22
and the MAXsa™ 29 Wire drives. See Figure B.1
a. Always cut the end of the wire to a sharp
point.
Turn the Cross Seam Adjuster (MAXsa™ 29) to keep
the arc in the joint as necessary. With a MAXsa™ 22,
a K96 or some other means of horizontal adjustment
is recommended. See Figure B.2
b. Press Feed Forward until the wire touches
the work piece and the flux hopper acti-
vates to put flux around the starting point.
The entire Wire Drive can be moved into or out of the
Mounting Bracket (M6789). If using a K29 Vertical Lift
Adjuster it can be locked in either the horizontal or
vertical position once the vertical position is set. See
Figure B.3.
c. Press Feed Reverse to retract the wire 1/8”
to 1/4” (3.2-6.4mm).
d. Use the Set-Up menu of the MAXsa™ 10
or remote controller to determine whether
the travel will begin with Start Button
pressed or with weld current (preferred).
If the Wire Drive is rotated to a position where the
faceplate is upside down, the contact nozzle and the
wire straightner and guide tubes will need to be
reversed. The polarity of the motor will also need to be
changed so the wire feeds in the proper direction. See
the Installation Section, Changing the Wire Drive
Configuration for instructions on changing the motor
polarity.
e. Press the START button to initiate the weld.
f. Press the STOP button to begin the stop-
ping sequence.
h. If necessary, press the Feed Reverse to
move the electrode out of the way.
MAXSA™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
B-2
B-2
OPERATION
FIGURE B.1 - FEED HEAD ADJUSTMENT
The Cross Seam Adjuster
Can Be Mounted to the
Top or Bottom of the
Gear Box
Loosen this Socket
Head Screw to Adjust
Faceplate Angle
5/16”
Allen
Wrench
Feed Head Rotates
360° Around the
Motor Axis
Face-plate Rotates
360° Around the
Drive Roll Shaft
FIGURE B.2 - HORIZONTAL ADJUSTMENT
This Adjustment Can be
Locked by Tightening
Two Socket Head Screws
Turn Handle
to adjust
MAXsa 29
MAXsa 22
Rotating the K96 Allows
for 2” Movement in
any Direction in the
Horizontal Plane
2”
2 1/2”
K96 Horizontal Adjuster
FIGURE B.3 - VERTICAL ADJUSTMENT
Cross Seam Adjuster
Use This Screw
To Lock Vertical
Position
Head May Be Rotated
Around the Vertical Axis
K29 Clamps Can Be Set
to Restrict In and Out Motion
to Distances up to 3 3/4”
K96
Loosen to Rotate
Entire Head Around
Mounting Axis
With K29
Head
Mounting
Loosen Screw
With Standard Mounting (M6767)
or K96 Horizontal Adjuster
With Standard Mounting (M6767)
or K29 Vertical Adjuster
MAXSA™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-1
C-1
ACCESSORIES
OPTIONS AND ACCESSORIES are
Follow these steps:
2. In the Search field type E9.181 and click on the
Search icon (or hit ʻEnterʼ on the keyboard).
3. On the Results page, scroll down to the
Equipment list and click on E9.181.
All of the information for the Power Wave System
accessories can be found in this document.
K2311-1 Motor Conversion Kit (for 142:1
NA Style Wire Drives)--This convertion kit con-
verts old NA style wire drives to MAXsa™ 22 & 29
WIRE DRIVES.
1. Remove the 2 hex head screws and the 2 slot head
screws holding the Motor to the Wire Drive Gearbox
assembly.
2. Remove existing Adapter Plate and Motor Assembly.
3. The Conversion Kit Motor is shipped configured for a
142:1 gear ratio. The existing gearbox must be con-
figured for a 142:1 gear ratio for the Conversion Kit to
assemble correctly. If both assemblies are not con-
figured for the same gear ratio, this must be done
before continuing. (See Gear Ratio Conversion Kit
instructions.)
4. Cover the teeth of the new Motor pinion gear with a
non-fluid molydisulfide type grease such as Non-Fluid
Oil Corporationʼs A-29 Special/MS Lubricant. This
grease can be scooped from the cavity of the gear
case First Chamber.
5. Reassemble the new Adapter Plate and Motor
Assembly on the Wire Drive Gearbox; making sure
the gears mesh properly and the Adapter Plate locat-
ing bead is in its cavity. Replace and tighten the 4
screws removed in step 1.
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-2
C-2
ACCESSORIES
Connect the lug on the electrode cables from the
power source to the tab on the contact nozzle
and tighten the bolt and nut. See Figure C.1.
SUBMERGED ARC CONTACT
ASSEMBLIES
K231-[X/XX] CONTACT NOZZLE
Operation - DO NOT completely straighten the
electrode. A slight curvature is required in the
electrode to insure good electrical contact inside
the contact tip.
The K231- [x/xx] is used for submerged arc weld-
ing with currents generally under 600 amps.
Higher currents can be used but result in some-
what faster tip wear. The outer flux cone deposits
flux around the arc for full coverage with mini-
mum flux consumption.
Maintenance - Replace the contact tip when it
no longer provides accurate wire location or good
electrical contact. Rusty and dirty wire or exces-
sively high currents increase tip wear. Always
keep replacement tips in stock.
Contact tips for the electrode diameter specified
on the order are shipped with each nozzle. A dif-
ferent contact tip is required for each electrode
diameter used.
To replace the contact tip, first loosen the retain-
ing wing nut and remove the flux cone body.
Then unscrew the tip and replace it.
Installation - Nozzles ordered for 3/32” (2.4 mm)
electrode include a liner and a contact tip
adapter. Screw the adapter into the end of the
nozzle and the contact tip into the adapter.
A special socket head screw holds the nozzle
body to the insulator. If the nozzle body becomes
loose, remove the nozzle from the head, tighten
the screw and reassemble nozzle.
Insert the outgoing wire guide from the wire feed
head into the top of the K231 and install the
assembly in position on the bottom of the wire
feed head. Lock it in position using the two
clamps provided with the head.
Extensions - The K231 nozzle can be extended
if necessary. Order part number S12003 for a 5”
(127mm) extension or make any length per draw-
ing in Figure C.2.
Connect one end of the rubber flux hose to the
tube at the bottom of the flux hopper. Fit the
short copper tube in the other end of the rubber
hose then insert the copper tube into the hole in
the flux cone body. See Figure C.1
FIGURE C.2 - EXTENSION
+
60°_
2°
1/32”x45°
Chamfer
Remove Sharp
Corner
9/16-18
Class 2 Fit
CAUTION - Pushing the copper tube too far into
the flux cone body will cause a short
between the cone and nozzle if the
cone touches the work.
1/2”
1/8”
1/2”
FIGURE C.1 - K231
Material - Hard Drawn
Copper or Heat Treatable
Copper Alloy
As
Req’d
Socket Head
Screw
Weld Cable
Connection
33/64”Drill 11/16” deep
9/16-18 Tap 9/16” deep
Class 2 Fit
Flux
Hose
Wing
Screw
1/32”x45°
Chamfer
Break
Corner
3/4”
Copper
Tube
Flux Cone
Body
“A” Dia. (See Table)
Wire Size
“A” Dim.
5/64-3/32(2.0-2.4mm) 1/8 (3.2mm)
1.8-5/32 (3.2-4.0mm) 3/16 (4.8mm)
3/16 -7/32(4.8-5.6mm) 1/4 (6.4mm)
Flux Cone
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-3
C-3
ACCESSORIES
K226 CONTACT ASSEMBLY
Maintenance - Rusty or dirty wire and/or exces-
sively high welding currents increase wear on the
contact jaws. When arcing occurs or the elec-
trode becomes loose in the jaws, remove the
jaws and ʻdressʼ them with a file. When neces-
sary, the jaw inserts should be replaced.
The K226 assemblies are used for welding at currents
from 600 to 1000 amps.
Model K226-T - (2 tapered jaws)
3/32” and 1/8” (2.4 and 3.2mm) electrode
NOTE: Units made prior to 1979 did not have
inserts. The replacement jaws will have
them.
Model K226-R - (1 tapered and 1 rectangular jaw)
1/8” thru 7/32” (3.2 - 5.6mm) electrode
Installation - Remove the two nozzle mounting
clamps from the wire drive. Insert the outgoing
wire guide from the wire feed head into the top of
the K226 and install the assembly in position on
the bottom of the wire feed head. Use the two
screws provided with the K226 to attach it to the
wire drive. See Figure C.3.
The contact jaws must be kept in line with the
wire guide. Align the jaws as follows: (See Figure
C.3)
1. Loosen the stationary contact jaw screws.
2. Release the tension on the moveable jaw by
loosening the screws holding the spring.
NOTE: Removing the 4 screws that hold the noz-
zle body to the mounting block allows the
nozzle to be rotated to any of four posi-
tions 90° apart. See Figure C.3.
3 Place a straight 14” (or longer) piece of bare
5/32” (4.0mm) wire through the wire guide
and into the drive rolls of the feed head.
Connect two (2) electrode cables to the contact
jaws (one under each 1/2-13 nut. Make sure that
the cable lugs are flat against the copper and
tighten the nuts securely. See Figure C.3.
4. Adjust the stationary contact so the wire
touches the jaw at the center of the groove
for the entire length of the jaw.
Slip the rubber flux hose that comes with the
K226 on to the flux hopper valve. Fit the copper
tube into the other end and place it in the clip on
the lower jaw assembly. See Figure C.3.
5. Tighten the screws, remove the wire and re-
tighten the screws holding the spring to
apply tension to the moveable jaw. The
moveable jaw should move freely when fin-
ished.
FIGURE C.3 - K226 CONTACT NOZZLE ASSEMBLY
Use to Mount
to Wire Drive
Remove(4)
Screws to
Rotate Nozzle
Stationary
Contact
Attach Weld
Cables Here
Spring
Moveable
Contact
Flux
Hose
K226-R
Only
Copper Tube
WORK
TRAVEL
NOZZLE
TRAVEL
MAXSA™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-4
C-4
ACCESSORIES
K148 CONTACT NOZZLE AND K149 Linc-FillTM
LONG STICKOUT EXTENSION
7. Slide the center guide (G) up out of the pivot body
until the tang is above the window.
8. Place the Linc-Fill guide assembly into the nozzle
window, and then lower the center guide tube (G)
back down to its original position.
This nozzle is available in three models and can be
used for Innershield® or submerged arc processes.
K148-A - For 3/32” and 1/8” (2.4 - 3.2mm) wire.
K148-B - For 5/32” and3/16” (4.0 - 4.8mm) wire.
K148-C - For 1/16” to 5/64” (1.6 to 2.0mm) wire.
Current Ratings
9. Line up the spot at the top of the center guide tube
(G) with the 3/8” (9.5 mm) tapped hole in the upper
pivot block (A) and put the 3/8” (9.5 mm) set screw
(C) back into the hole and tighten securely.
FIG. C.4 - TYPICAL CONFIGURATIONS
A. Without Linc-Fill Attachment
Innershield Welding:
600 amps, 100% duty, no water cooling
1100 amps, 100% duty, with water cooling
Submerged arc welding:
1100 amps, 100% duty, no water cooling
B. With K149 Line-Fill Attachment
Innershield or Submerged Arc Welding:
1100 amps, 100% duty, no water cooling
K 148
K 148
With Water
Cooling
Water Cooling Attachment
K 148 & K 149
Attachment
When using currents over 600 amperes at high duty
cycles water cooling always increases contact tip life.
The cooling attachment, Part No. T12928 must be
ordered seperately. Installation instructions are includ-
ed in the kit. Connect the attachment to the water sup-
ply and the drain with rubber tubing obtained locally.
Water flow should be between 1/2 to 1 gallon (1.9 to
3.8L) of tap water per minute.
FIG. C.5 - K149 INSTALLATION
C
A
B
K149 Installation (See Figure C.5)
1. Install the K149 attachment before mounting the
K148 nozzle on the welder.
F
2. Place a small C-clamp on the spring supporting
members (A) and (B) in such a manner that the
spring can be compressed. Look up into the hole
in the end of contact tip and tighten the C-clamp
until the tang lifts off the surface of the tip.
G
H
E
D
3. Remove the 3/8” (9.5 mm) set screw (C) in the
body (A).
11
4. Remove the contact tip clamping nut (D) and the
contact tip.
12
5. Remove the brass thread protecting collar (E).
13
14
10
6. Remove the dirt shield (F) from the barrel of the
nozzle.
MAXSA™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-5
C-5
ACCESSORIES
10. Line up the lower spot in the center guide tube (G)
with the 3/8” (9.5 mm) set screw (H) and tighten the
screw securely.
Operation
The same contact tip, S13763, is used for 3/32” (2.4
mm) through 3/16” (4.8 mm) diameter electrodes.
S16388 is used for .062 (1.6 mm) and 5/64 (2.0 mm)
electrode.
11. Replace the brass thread protecting collar (E). It is
important that this protecting collar be pulled up
against its locating shoulder, otherwise the tip lock-
ing nut will not clamp the tip securely.
Loading of Wire
12. Replace the contact tip and its clamping nut (D)
and tighten securely.
Straighten the start end of the coil for at least eight inch-
es, pass the end down through the appropriate wire
straightener. Inch the wire through the wire feeder and
the nozzle. When using .062 (1.6 mm) or 5/64 (2.0 mm)
Innershield electrode with a K148-C nozzle, make sure
that the wire is in the “vee” groove of the pressure tang.
For the .062 (1.6 mm) and 5/64 (2.0 mm) wire sizes, it
may be necessary to back off on the idle roll pressure
so that there is little or no flattening of the wire.
13. Assemble the proper combination of extension
guides (Items 12, 13 and 14) with locking nut (Item
11) for the welding procedure to be used.
14. For Submerged Arc welding, screw the flux hose
clamp (Item 10) onto the extension housing.
K148 Nozzle Installation
Because the electrode is held against one point of the
contact tip, it wears a groove at that point. When the
groove is about one half the diameter of the electrode,
rotate the contact tip to a new position per the instruc-
tions below. Careful positioning of the contact tip will
provide four to six wear spots depending upon the elec-
trode size.
To install the nozzle on the head, insert the outgoing
wire guide from the head into the nozzle assembly.
Place the combined assembly in position on the bottom
of the wire feed roll box. Clamp it in place using the two
clamps supplied with the head.
Before pulling the clamps up tight the nozzle must be
positioned relative to the travel direction as shown in
Figure C.6. This position is set so accidental contact
between the work and the nozzle will not compress the
contact pressure spring. If positioned otherwise, such
accidental contact may cause arcing inside the contact
tip.
After the nozzle is positioned in the proper relationship
with the travel direction, the connector tab for the elec-
trode cables can be moved to any of four positions 90
degrees apart. To change the tab, remove the two 1/4-
20 hex head screws. ap the connector tab to loosen it
from the tapered collar on the nozzle body. Turn the tab
to the desired position. Replace and tighten the 1/4-20
screws.
When welding with the small diameter electrodes, it will
be necessary to change contact position more frequent-
ly since the amount of tip wear that can be tolerated is
much less. The tang should never be allowed to touch
the I.D. of the contact tip. If the groove is allowed to
wear until the tang touches the I.D. of the contact tip,
welding current passes through the tang. This causes
electrical wear and overheating of the tang and the con-
tact tip. See Figure C.7.
FIGURE C.7
Contact
Tip
FIGURE C.6
Tang
Electrode
Nozzle
Pivot
Time to
Rotate
New
Too Late
Connector
Tab
Contact
Pressure
Spring
To rotate the tip, clip the end of the electrode and inch it
up until it is free of the contact tip. Loosen the locking
nut about one-half turn and pull the nozzle body to
relieve the pressure of the tang against the inside of the
contact tip hole. At this moment rotate the tip the proper
amount and then retighten the locking nut.
Locking
Nut
Nozzle
Travel
Work
Contact
Tip
Travel
MAXSA™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-6
C-6
ACCESSORIES
To install a new contact tip proceed as follows:
K285 Installation to the K148
1. Clip the end of the electrode and inch it up until it is
free of the tip.
1. Remove the tension on the center guide tube using
a “C” clamp as shown in Figure C.8. Apply only
enough clamping force to relieve the tang pressure
from the contact tip.
2. Remove the contact tip locking nut.
3. Relieve the spring pressure of the contact tip against
the steel tang in the hole of the contact tip. To do
this, push the nozzle body so the steel tang is
approximately centered in the 3/8” (9.5 mm) hole in
the contact tip. Under these conditions the contact
tip can be easily removed from the nozzle body.
2. Remove the contact tip clamping nut and the con-
tact tip.
FIGURE C.8
4 a. Before installing the new tip, make sure the
threads and the bottom surface of the nozzle are
clean and bright. These surfaces are current car-
rying areas and must be clean.
b. Push the nozzle body to one side to relieve the
pressure and insert the new contact tip.
5. a. Check the locking ring threads making sure
they are free or any foreign material. A small
application of locally available high temperature
anti-seize compound or graphite grease on
these threads insure a longer thread life of the
two mating parts.
3. Remove the brass thread protecting collar and
slide the dirt shield off of the nozzle.
4. Make sure that all the threads are clean and
replace the collar, the contact tip and the clamping
nut and remove the “C” clamp.
b. Replace the locking ring and tighten securely.
5. Loosen the hose clamps of the K285 entirely, place
them around the nozzle and tighten them so that
the stationary part of the K285 covers the opening
in the nozzle body as shown in Figure C.9.
6. Check the contact tip to be certain it is tight in the
nozzle body. If the tip is not tight, arcing will take
place between the tip contact surface and the noz-
zle contact surface which will damage the nozzle
body.
6. Position the moveable section to the desired flux
height and tighten the wing nut.
K285 Concentric Flux Cone
7. Cut the flux hose to required length and connect as
shown.
The K285 Concentric Flux Cone is designed to fit on a
K148 (with or without the K149 attachment) or on a
K129 Tiny Twin-Arc® nozzle. This attachment
deposits the flux so that it surrounds the electrode(s).
FIGURE C.9 - K148
NOTE: If using a K149 extension, the electrical stick-
out will be limited to 4” (102mm).
Wing Nut
Flux
The K285 consists of two pieces that are electrically
isolated from each other. The stationary segment is
clamped to the nozzle and the moveable portion
which supports the flux hose and the concentric cone
allows for vertical adjustment of the flux cone.
Hose
Clamps
Hose
Moveable
Section
Travel
Direction
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-7
C-7
ACCESSORIES
K285 Installation with K149
K285 installation with the K129
1. Install the K149 to the K148 per the instructions.
1. Unscrew the hose clamps enough so they can slip
over the tip holder clamping nut.
2. Loosen the hose clamps of the K285 entirely, place
them around the nozzle and tighten them so that
the stationary part of the K285 is directly opposite
the K149 arm. See Figure C.10
2. Position the stationary portion of the K285 as
shown in Figure C.11 and tighten the clamps.
3. Position the moveable section to the desired flux
height and tighten the wing nut.
NOTE: The lower hose clamp must be positioned so it
does not touch the arm of the K149.
4. Due to the 7° angle of the tips it may be necessary
to pivot the cone as shown. Remove the outermost
screws from each side of the cone. tilt the cone
and put the two screws into the rear of the cone.
Tighten all 4 screws.
4. Position the moveable section to the desired flux
height and tighten the wing nut. Use the center or
lower tapped hole depending on the electrical
stickout
5. Cut the flux hose to required length and connect as
shown.
5. Cut the flux hose to required length and connect as
shown.
FIGURE C.11 - K285/K129
FIGURE C.10 - K285/K149
IMPORTANT
K285 on ALL Nozzles
After the K285 is installed to any of the compatible
nozzles, use an ohmmeter or a test light to insure
proper insulation (no continuity) between the copper
flux cone and the nozzle body
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-8
C-8
ACCESSORIES
K285 Used in Horizontal Fillet Applications
1. With K148 or K148/K149 combination - After the
c. Loosen the K285 hose clamps and rotate the flux
cone unit about 40 to 45° and retighten the
clamps.
K285 has been attched to the nozzle body:
a. Set the head and nozzle to the desired electrode
angle.
d. Slide the K285 flux cone dowm to about 1/8”
(3.0mm) away from both the vertical and horizon-
tal plates and tigten the wing screw. See Figure
C.12.
b. Loosen the two hold down screws that hold the
nozzle to the faceplate and rotate the entire
assembly 40 to 45° and retighten the screws.
K285 in Deep Narrow Gap Applications
c. Feed the electrode to the proper stickout and
position it in the joint.
For narrow, deep groove welds it may be necessary to
remove the copper cone from the moveable arm of
the K285
d. Slide the K285 flux cone dowm to about 1/8”
(3.0mm) away from both the vertical and horizon-
tal plates and tigten the wing screw. See Figure
C.12.
NOTE: In Horizontal fillet pplications, the flux hopper
will not function properly if fastened to the
faceplate of the wire drive. Mount the Flux
hopper directly above the K285 flux entry
point. Flux hose angles should be no greater
than 35° to ensure good flux flow from the
hopper to the cone.
2. With the K129 Tiny Twin-Arc® Nozzle - After the
K285 has been attached to the nozzle body:
a. Set the head and nozzle to the desired electrode
angle.
b. Feed the electrode theough the tips to the proper
stickout and place the nozzle into the welding
position.
FIGURE C.12 - K285 IN HORIZONTAL FILLET APPLICATION
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-9
C-9
ACCESSORIES
K29 VERTICAL HEAD ADJUSTER
4. Slide the Head Adjustment Lock (A) over the end
of the Mounting Bracket (M).
Automatic welding applications frequently require rais-
ing and/or lowering of the feed head assembly. The
K29 provides an easy method of accomplishng this
task by simply turning a crank handle. A height varia-
tion of 4” (102mm) is possible with this attachment.
5. Align the hole of the Head Adjustnent Lock with
the groove in the Mounting Bracket and drive in
the 1/4” Roll Pin (B).
FIGURE C.13 - K29
6. Using the 1/2” x 2.75 Locking Screw, tighten the
Head Adjustment Lock with the open slot in the up
position.
7. Slide the Vertical Head Lift Adjuster (E) into the
Mounting Bracket (M) and tighten the Draw Bolt
Nut (K).
8. Install the two Clamps (D), one on each side of the
Head Adjustment Lock with the hardware provid-
ed.
NOTE: If a K96 Horizontal Adjuster is to be used,
install it now per the instructions provided. If
not, proceed to Step 9.
9. With the Draw Bolt (J) and the Lock Nut (H) in
place, raise the Feed Head in to position on the up
and down lift shaft (N) and tighten the Lock Nut.
10. Drive the 5/16” Roll Pin (G) back in to itʼs original
position.
Installation
Adjustment and Locking
Check the package for the following items (See Figure
C.13):
Rotational movement of the lifting mechanism is kept
to a minimum by the spring loaded, wedge shaped pin
(X) that is always in contact with the vertical slide. The
Socket Head Screw (Y) on the right side of the K29
housing is used as a locking mechanism to keep the
head at a desired height.
1. Head Adjustment Lock (A)
2. 1/4” (6.3mm) diameter Roll Pin (B)
3. 12”-13x2.75” Hex Head Locking Screw (C)
4. Two adjustable clamps with hardware (D)
5. Vertical Head Lift Adjuster (E)
NOTE: Extreme tightening of the locking screw may
cause the wedge to jam so that the lift cannot
move in either direction. If this occurs, back
the screw out two turns and tap on it to
release the wedge.
To install the K29, proceed as follows:
1. If the Feed Head (F) is already mounted to the
Head Support (E), be sure that the lock nut (H) on
the Feed Head Draw Bolt (J) is tight, and drive out
the Roll Pin (G) with a 5/16” punch.
2. While supporting the Feed Head, loosen the lock-
ing nut (H) and remove the head from the Head
Support (E).
3. Loosen the Lock Nut (K) on the Draw Bolt (L) and
remove the Head Support (E) from the Mounting
Bracket (M).
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-10
C-10
ACCESSORIES
K96 HORIZONTAL HEAD ADJUSTER
FIGURE C.14 - K96
The K96 provides an easy means of moving the Feed
Head in a horizontal direction by simply turning a
crank handle. It provides 2” (51mm) of travel and can
be mounted directly to the Head Support or to a K29
Vertical Lift Adjuster.
Installation (See Figure C.14)
1. If the Feed Head is already mounted, make sure
that the Lock Nut (H) on the Feed Head Draw Bolt
(J) is tight and drive out the Roll Pin (G) with a
5/16” punch.
2. While supporting the head, loosen the Lock Nut
(H) and remove the Feed Head
NOTE: If a K29 Vertical Head Adjuster is to be used,
install it now per the instructions provided.
3. With the Draw Bolt (A) in place, fit the K96
Horizontal Adjuster (D) over the shaft of the Head
Support (E) or the K29 (Eʼ ) if used.
4. Drive in the 1/4” Roll Pin that comes with the K96.
5. With the Draw Bolt (J) and the Lock Nut (H) in
place, raise the Feed Head in to position on the
shaft of the Horizontal Adjuster and tighten the
Lock Nut.
6. Drive the 5/16” Roll Pin (G) back in to itʼs original
position.
7. Mount the Crank Handle on whichever side is
most convenient by removing the two bolts and
rotating the housing 180° and replacing the bolts.
See Figure C.15.
FIGURE C.15
Place Handle in
Either of Two
Positions
Remove Two Bolts
and Rotate Housing
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-11
C-11
ACCESSORIES
FIGURE C.16 - K129 TINY TWINARC® COMPONENTS
1
D
A
7
6
2
E
C
B
3
5
4
3
4
1 - Nozzle Assembly
A - Drive Rolls
2 - Guide Tubes
3 - Locking Collar
4 - Contact Tip(s)
5 - Tip Holder
6 - Connection Tab
7 - Mounting Block
B - Guide Tubes
C - Idle Roll Arm
D - Incoming Wire Guide
E - Drive Roll Spacer
F - Key
K129 TINY TWINARC® KIT
Drive Kit for use with the K129-1/16 kit.
INSTALLATION
Twin arc welding is a process where two wires of the
same size are fed through a nozzle by a single wire
drive. The K129-x/xx can be used for wire sizes .045”
through 3/32” (1.0 - 2.4mm).
A. For .045” through 5/64”(1.0-2.0mm) Wires
1. Remove the following items from the standard
Feed Head.
• The wire straightener
The gear ratio of the MAXsa™ 22 & 29 WIRE DRI-
VES as shipped is 142:1. This may not provide
enough wire speed for the procedure. Conversion kits
for 95:1 or 57:1 ratio are also shipped with the
MAXsa™ 22 & 29 WIRE DRIVES units. See the
instrucutions included with those kits or in this manual
to change the gear ratio.
• The nozzle assembly
• Both upper and lower guide tubes
• The drive rolls
• The idle roll assembly
• The tension spring assembly
NOTE: The idle roll arm pivot pin is held in place by
a set screw that is accessed from the outgo-
ing surface of the faceplate.
Each assembly listed below comes with a wire reel, a
reel brake, shaft and mounting bracket and all of the
wire drive components for the particular wire size.
2. Place the new double grooved drive roll (A) on
the shaft with the key. Replace the clamping
washer and the locking nut and tighten securely.
K129-1/16
K129-5/64
K129-3/32
.045” thru 1/16” (1.0 -1.6mm) Wires
5/64” (2.0mm) Wire
.
3/32” (2.4mm) Wire
NOTE: For .045” or .052” wire order KP1901-1 Wire
MAXSA™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-12
C-12
ACCESSORIES
B. For 3/32 (2.4mm) Wire
1. Remove the items listed in Step “A” plus:
5. Insert the two long insulated wire guides (2) into
the Twinarc nozzle (1) making sure that they are
seated in the holes in the mounting block (7).
Place the contact tip (4) or tip holder (5) into the
end of the nozzle making sure the tubes fit into
the holes. Lock it securely in place with the lock-
ing collar (3). See Figure C.16.
• The drive roll key
• The drive roll spacer
NOTE: The set screw that holds the drive roll spacer
in place is accessible once the idle roll assem-
bly is removed.
2. Oil or grease the O.D. of the new shorter drive
roll spacer (E) and place it on the output shaft.
Push it back as far as it will go and tighten the
set screw.
NOTE: For applications that require staggered or
cross seam wire placement rather than in-line,
the contact tip or tip holder may be rotated.
Re-adjust the head position to maintain the
proper wire-to-work angle.
3. Place the new longer key (F) in the keyway.
For overlay applications a special “side by
side” tip holder (part# S17728) that accepts
standard contact tips is available.
4. Place the outer, center and second outer drive
rolls (A) on the shaft. Replace the clamping
washer and the locking nut and tighten securely.
6. Place the other guide tube (B) into the outgoing
side of the faceplate. Place the nozzle over the
guide tube and lock it in place with the two sock-
et head screws
FIGURE C.17
Key
Outer Drive Rolls
7. Bolt the electrode cable(s) of the proper size and
number, to the connection tab (6) using the hard-
ware provided. If using multiple cables, use both
sides of the tab.
Locking
Nut
Drive Roll
Spacer
Clamping
Washer
Center
Drive Roll
Output
Shaft
E. Maintenance
Replace the Contact Tip(s) when they no longer pro-
vide accurate wire placement or good electrical con-
tact. Before installing the new contact tip or tip holder:
See Figure C.17.
1. Make sure that the threads and bottom surface of
the nozzle are clean and bright. These are cur-
rent carrying surfaces and must be clean.
C. Nozzle Installation
1. install the new idle roll arm (C) using the pin and
set screw from the original assembly. .
2. Check that the locking collar is free of foriegn
material. A coating of locally available “anti-
seize” compound or graphite grease will help
insure longer thread life.
2. Replace the tension spring and screw and adjust
the tension screw to the .045-3/32 line on the
indicator plate.
3. Before replacing the contact tip or tip holder:
a. Inch the wire past the end of the nozzle.
b. Slide the long wire guides on to the wire
making sure they are properly seated in the
mounting block (see Figure C.16).
3. Insert one of the guide tubes (B) in the top of the
faceplate. Line up the holes in the guide tube
with the grooves in the drive rolls to insure proper
wire feed
c. Slide the new contact tip or tip holder over
the wires again making sure that thewire
guides are properly seated
NOTE: If using the K281 Twinarc Wire straightener,
follow the supplied instructions and skip to
Step 5.
d. Replace the locking collar and tighten
securely
4. Put the dual ingoing wire guide (D) over the ingo-
ing guide tube and lock it down with the two “L”
shaped clamps from the wire straightener.
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-13
C-13
ACCESSORIES
FIGURE C.18 - K225 TWINARC® COMPONENTS
1
F
A
2
9
D
C
B
3
5
A - Drive Rolls
B - Guide Tubes
C - Idle Roll Arm
D - Drive Roll Spacer
E - Key
7
8
F - Nozzle Assembly
6
4
K225 SUBMERGED ARC TWINARC® KIT
NOTE: The idle roll arm pivot pin is held in place by a
set screw that is accessed from the outgoing
surface of the faceplate.
Twin arc welding is a process where two wires of the
same size are fed through a nozzle by a single wire
drive. The K225 Twinarc Kit can be used to weld with
5/64”, 3/32” or 1/8” (2.0,2.4,or3.2mm) electrodes. Both
wires must be the same size.
• The tension spring assembly
`
• The Drive Roll Spacer
NOTE: The set screw that holds the drive roll spacer
in place is accessible once the idle roll assem-
bly is removed.
The gear ratio of the MAXsa™ 22 & 29 WIRE DRI-
VES as shipped is 142:1. This may not provide
enough wire speed for the procedure. Conversion kits
for 95:1 or 57:1 ratio are also shipped with the
MAXsa™ 22 & 29 WIRE DRIVES units. See the
instructions included with those kits or in this manual
to change the gear ratio.
2. Oil or grease the O.D. of the new shorter drive
roll spacer (E) and place it on the output shaft.
Push it back as far as it will go and tighten the
set screw.
3. Place the new longer key (F) in the keyway.
Each assembly comes with a wire reel, a reel brake,
shaft and mounting bracket, a dual wire straightener
and all of the wire drive components for the particular
wire size. See Figure C.18.
4. Place the outer, center and second outer drive
rolls (A) on the shaft. Replace the clamping
washer and the locking nut and tighten securely.
See Figure C.19.
The Nozzle Assembly (F) has two spring loaded large
copper jaws (6) that press the electrodes against the
copper center block (4). This system provides good
elctrical contact and insures constant electrical stick-
out (E.S.O.) It also helps to maintain acceptable noz-
zle temperatures during welding.
FIGURE C.19
Key
Outer Drive Rolls
INSTALLATION
Locking
Nut
Drive Roll
Spacer
Clamping
Washer
Center
Drive Roll
Output
Shaft
1. Remove the following items from the standard
Feed Head.
• The wire straightener
• The nozzle assembly
• Both upper and lower guide tubes
• The drive rolls
• The idle roll assembly
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-14
C-14
ACCESSORIES
Nozzle Installation (See Figure C.18)
IMPORTANT
Make sure that the mating surface (8) between the
Center Block (4) and the Copper Bar (2). is bright,
clean and smooth. This junction carries the full weld
current.
1. install the new idle roll arm (C) using the pin and
set screw from the original assembly.
2. Replace the tension spring and screw and adjust
the tension screw to the proper line on the indica-
tor plate.
FIGURE C.20
3. Insert one of the guide tubes (B) in the top of the
faceplate. Line up the holes in the guide tube
with the grooves in the drive rolls to insure proper
wire feed
1
2
4. Put the Dual Wire Straightener over the ingoing
guide tube and lock it down with the two “L”
shaped clamps
9
5. Place the other guide tube into the top of the
K225 Nozzle Assembly (F) and slide the guide
tube into the Wire Drive faceplate until the
mounting screws (1) can be started into the
tapped holes in the faceplate. Tighten both
screws.
3
5
7
NOTE: For applications that require staggered or
cross seam wire placement rather than in-line,
the nozzle can be rotated by loosening the
two1/4-20 socket head screws (9) that hold
the nozzle to the mounting base. If the desired
angle cannot be obtained, remove the screws
and put them into alternate holes. Retighten
when properly adjusted.
8
6
4
Maintenance
The most extensive contact wear takes place on the
center contact block. The side pressure jaws are
made of a harder longer lasting material. Replace the
center block when there is no pressure on the wire
from the side contact jaws.
6. Connect the weld cables of the proper size and
number to the copper bar (2). If using multiple
cables, use both sides of the bar.
7. Route the flux hose from the flux hopper to the
clip (3) on the K225 nozzle.
Make sure that the mating surface (8) between the
Center Block (4) and the Copper Bar (2). is bright,
clean and smooth. This junction carries the full weld
current.
8. Spacing between the electrodes is maintained by
the center block which comes in three sizes. The
.50 “ and .625” center blocks come with the kit. A
.375” block is also available. See the parts list for
the part number. To change the center block,
See Figure A-30:
• Loosen both of the Pressure Springs (5)
• Remove the two Socket Head Screws (7)
• Put a small amount of graphite grease on
the screw threads and install the new copper
block.
• Replace the two screws and tighten securely
• Tighten the four screws holding the Pressure
springs
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
C-15
C-15
ACCESSORIES
4. Insert one wire through each of the guide block
holes.
K281 SOLID WIRE STRAIGHTENER FOR
TINY TWINARC®
5. Push both wires through and between the rollers
and down through the guide tube until they touch
the drive roll(s). Press the Cold Inch to start the
wires through the wire drive.
The K281 wire straightener can be used to straighten
.045” through 3/32” (1.0-2.4mm) wiress. It is recom-
mended for applications requiring long stickout and/or
where accurate wire placement is essential. The fol-
lowing table shows the recommended maximum ele-
crical stick-out (ESO).
6. Replace the upper guide block making sure that
each wire is in its respective groove of both
rollers. Tighten the thumb screw.
ESO - Standard
ESO - K281
Wire Size (mm) Wire Guide (mm) Straightener (mm)
7. Turn the adjusting knob until the moving arm is
.045” (1.0)
.052” (1.3)
1/16” (1.6)
5/64” (2.0)
3/32” (2.4)
3/8” (9.5)
1/2” (12.5)
3/4” (19.0)
1.00” (25.4)
1-1/4” (32)
5/8” (16.0)
3/4” (19.0)
1-1/4” (32.0)
1-3/4” (44.5)
2.0” (51)
approximately at the mid position of its total trav-
el.
FIGURE C.21
E
C
D
GENERAL INFORMATION
1. For best wire straightening the plane of the
K281rolls (A) should be as close as possible to
the plane of the wire reels.
B
A
2. The K281 moving arm (B) should be pointing
toward the wire reels and the adjusting knob (C)
should be away from the reels.
3. The K281 can be mounted to the wire drive in
two different positions. The head can then be
positioned to meet the above requirements.
Under
Over
Straightened
Straightened
INSTALLATION
1. Remove the Spring Wire Guide if installed.
2. Remove the K129 Ingoing Guide Tube.
The tips should be in line with the O.D. of the drive
rollsfor initial strightening adjustment. If the wires bow
to the right when inched down through the tips they
are being over straightened. If the wires bow to the
left, they are being understraightened. Adjust the knob
until the wires come out parallel and uniform.
3. Insert the new Ingoing Wire Guide (with ceramic
inserts) that comes with the K281.
4. Position the K281 over the wire guide as outlined
above and tighten the two hex head screws.
Depending on how the wire enters the K281, there
may be some side bow. Slight rotation of the K281
may eliminate this condition.
WIRE LOADING AND ADJUSTMENT
Once the wire is sufficiently straight, the tip orientation
can be changed to whatever angle between “in-line”
and “cross seam” is required.
1. Turn the adjusting knob (C) to the maximum
open position.
2. Remove the top ingoing guide block (D) by loos-
ening the thumb screw (E).
NOTE: For overlay applications with Tiny Twinarc, a
special side by-side tipholder (Part # S17728
is available that accepts standard tips.
3. Straighten the first 10” (254mm) of each wire (the
straighter the wire the easier to load).
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
D-1
D-1
MAINTENANCE
SAFETY PRECAUTIONS
SENSE LEAD FUSE
There should never be any current flowing through
the sense leads! The sensing lead circuit is current
WARNING
®
protected in the Power Wave AC/DC 1000 SD.
If the MAXsa™ 22 & 29 Wire Drives are used in an
older system, a fuse in series with the #21 sense lead
in the wire drive Connection Box protects the sense
lead circuit from weld current due to incorrect configu-
ration. If this fuse ever opens, check the sense lead
configuration to ensure proper connections. The fuse
must be replaced with a comparable fuse with a rating
of less than 1 amp before welding. The fuse being
open or missing would have the same effect on the
welding as having a disconnected sense lead.
ELECTRIC SHOCK can kill.
• Only Qualified personnel should
perform this maintenance.
• Turn the input power OFF at the
disconnect switch or fuse box
before working on this equipment.
•
Do not touch electrically hot parts.
ROUTINE MAINTENANCE
• Check weld cables, control cables and gas hoses for
cuts.
• Clean and tighten all weld terminals.
• Inspect and clean drive rolls and inner wire guide
and replace if worn.
PERIODIC MAINTENANCE
• Every six months check the motor brushes. Replace
them if they are less than 1/4" long.
• Every year inspect the gearbox and coat the gear
teeth with a moly-disulfide filled grease. DO NOT
use graphite grease.
CALIBRATION SPECIFICATION
All calibration is factory set on the MAXsa™ Wire Drive.
To verify the wire feed speed:
• Adjust the wire feed speed to 100 in/min (2.54m/min)
and provide a COLD FEED Signal.
• Measure the actual wire feed speed with a calibrated
wire feed speed tachometer K283).
• The measured wire feed speed should be within 2%
of the set value.
NOTE: If a K283 is not available, feed wire for 15 sec-
onds and measure the wire. Repeat several
times to get an average measurement. It should
be 25” (635mm) +/-2%.
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
E-1
E-1
TROUBLESHOOTING
HOW TO USE TROUBLESHOOTING GUIDE
WARNING
Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel.
Unauthorized repairs performed on this equipment may result in danger to the technician and
machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical
Shock, please observe all safety notes and precautions detailed throughout this manual.
__________________________________________________________________________
This Troubleshooting Guide is provided to help you
locate and repair possible machine malfunctions.
Simply follow the three-step procedure listed below.
Step 3. RECOMMENDED COURSE OF ACTION
This column provides a course of action for the
Possible Cause, generally it states to contact your
local Lincoln Authorized Field Service Facility.
Step 1. LOCATE PROBLEM (SYMPTOM).
Look under the column labeled “PROBLEM (SYMP-
TOMS)”. This column describes possible symptoms
that the machine may exhibit. Find the listing that
best describes the symptom that the machine is
exhibiting.
If you do not understand or are unable to perform the
Recommended Course of Action safely, contact your
local Lincoln Authorized Field Service Facility.
Step 2. POSSIBLE CAUSE.
The second column labeled “POSSIBLE CAUSE” lists
the obvious external possibilities that may contribute
to the machine symptom.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
E-2
E-2
TROUBLESHOOTING
Observe all Safety Guidelines detailed throughout this manual
PROBLEMS
(SYMPTOMS)
POSSIBLE AREAS OF
MISADJUSTMENT(S)
RECOMMENDED
COURSE OF ACTION
OUTPUT PROBLEMS
Drive rolls turn, but wire will not
feed or wire feeding is rough or
uneven.
1. Wire jammed or kinked on route
through wire drive. Remove wire
from wire drive, then feed in new
wire. Note any obstruction.
2. Incorrect drives rolls and/or
guide tubes, or incorrect pres-
sure setting. Ensure drive rolls
and/or guide tubes are stamped
with wire diameter being used.
Replace if necessary. Check for
proper pressure setting.
3. Worn drive rolls. Replace, or
reverse if split type.
4. Partially flashed or melted con-
tact tip. Replace contact tip.
If all recommended possible areas
of misadjustments have been
checked and the problem persists,
contact your local Lincoln
Authorized Field Service Facility.
Variable or "hunting" arc.
1. Contact tip worn or incorrect
size. Replace contact tip.
2. Worn or undersized work cables
or poor connections to work.
Inspect and repair, or replace as
necessary.
3. Loose electrode connections.
The following connections must
be tight: electrode cable to wire
drive and power source, work
cable to power source and work,
contact tip to nozzle.
4. Rusty electrode. Replace elec-
trode.
Wire consistently runs at the wrong Gear ratio is not set properly. See
speed
the MAXsa™ 10 or the Power
Wave® AC/DC 1000 Operatorʼs
Manual to set the proper gear ratio.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
F-1
F-1
DIAGRAMS
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
F-2
F-2
DIMENSION PRINT
MAXsa™ 22 & 29 WIRE DRIVES
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not touch electrically live parts or
electrode with skin or wet clothing.
Insulate yourself from work and
ground.
Keep flammable materials away.
Wear eye, ear and body protection.
WARNING
Spanish
No toque las partes o los electrodos
bajo carga con la piel o ropa moja-
da.
Mantenga el material combustible
fuera del área de trabajo.
Protéjase los ojos, los oídos y el
cuerpo.
AVISO DE
PRECAUCION
French
Aislese del trabajo y de la tierra.
Ne laissez ni la peau ni des vête-
ments mouillés entrer en contact
avec des pièces sous tension.
Gardez à l’écart de tout matériel
inflammable.
Protégez vos yeux, vos oreilles et
votre corps.
ATTENTION
Isolez-vous du travail et de la terre.
German
Berühren Sie keine stromführenden
Teile oder Elektroden mit Ihrem
Körper oder feuchter Kleidung!
Isolieren Sie sich von den
Entfernen Sie brennbarres Material!
Tragen Sie Augen-, Ohren- und Kör-
perschutz!
WARNUNG
Elektroden und dem Erdboden!
Portuguese
Não toque partes elétricas e elec-
trodos com a pele ou roupa molha-
da.
Mantenha inflamáveis bem guarda-
dos.
Use proteção para a vista, ouvido e
corpo.
ATENÇÃO
Isole-se da peça e terra.
Japanese
Chinese
Korean
Arabic
READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE
USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOS
CONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.
LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS A
ETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.
LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSATZ DES HER-
STELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS ZU BEACHTEN.
Download from Www.Somanuals.com. All Manuals Search And Download.
Keep your head out of fumes.
Use ventilation or exhaust to
remove fumes from breathing zone.
Turn power off before servicing.
Do not operate with panel open or
guards off.
WARNING
Spanish
Los humos fuera de la zona de res-
piración.
Mantenga la cabeza fuera de los
humos. Utilice ventilación o
aspiración para gases.
Desconectar el cable de ali-
mentación de poder de la máquina
antes de iniciar cualquier servicio.
No operar con panel abierto o
guardas quitadas.
AVISO DE
PRECAUCION
French
Débranchez le courant avant l’entre-
tien.
N’opérez pas avec les panneaux
ouverts ou avec les dispositifs de
protection enlevés.
Gardez la tête à l’écart des fumées.
Utilisez un ventilateur ou un aspira-
teur pour ôter les fumées des zones
de travail.
ATTENTION
German
Strom vor Wartungsarbeiten
abschalten! (Netzstrom völlig öff-
nen; Maschine anhalten!)
Anlage nie ohne Schutzgehäuse
oder Innenschutzverkleidung in
Betrieb setzen!
Vermeiden Sie das Einatmen von
Schweibrauch!
Sorgen Sie für gute Be- und
Entlüftung des Arbeitsplatzes!
WARNUNG
Portuguese
Não opere com as tampas removidas.
Desligue a corrente antes de fazer
serviço.
Mantenha-se afastado das partes
moventes.
Não opere com os paineis abertos
ou guardas removidas.
Mantenha seu rosto da fumaça.
Use ventilação e exhaustão para
remover fumo da zona respiratória.
ATENÇÃO
Não toque as partes elétricas nuas.
Japanese
Chinese
Korean
Arabic
LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA AS
PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
Download from Www.Somanuals.com. All Manuals Search And Download.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|