Lytecaster® Recessed Downlighting 1004F18ES
®
Page 1 of 1
5" Aperture 0 1 Lt 18W Quad/Triple Tube Compact Fluorescent IC Frame-In Kit
5
6
7
5 3/4"
3
OVERALL
WIDTH
13" MIN.
24" MAX.
7 1/2"
OVERALL
HEIGHT
1
9"
OVERALL
LENGTH
4
5"
APERATURE
2
Ceiling Opening 5 3/8" diameter
Complete Fixture consists of Reflector Trim & Frame-In Kit. Select each separately.
Frame-In Kit
Reflector Trims — See Individual Reflector Trim Specification Sheets
Open Downlight
Enclosed
Wall
Washer
Voltage
Lamp
Diffusers
AnodizedReflector AnodizedCone
Satin Cone
Baffles
Basic White
1004F18ES
120V
18W
1045
1012
1008
1005
1071
1021
1035
Quad or 1046
1012NM
1013
1008NM
1010
1010NM
1005BNM
1005NM
1005WH
1076
1024
1078
1177LX**
1035WH
1085
1095
1096
1096CD
1004F18ESN
Triple
Tube
1046CD
1013BK
1013BKNM
1013CD
1013CDNM
1013NM
1013WH
1076WH
** Use Triple Tube Lamp Only.
Features
Electrical (cont.)
Max THD %: 10
Min Start Temp: 0˚F/ -18˚C
1. Housing: .032" (#20 ga.) UL listed for direct contact with thermal insulation.
Allows installation in ceilings up to 2" thick. Can be removed for access
to junction box, ballast and ceiling plenum. AirSeal® housing minimizes
air leakage to less than 2 CFM at 1.57 PSF (or 75pa), which complies with
Model Energy Code (Section 602.3.3) and Washington State Energy Code
(Section 502.4) and reduces heat loss and condensation in ceiling.
2. Mounting Frame: .048” (#18 ga.) galvanized steel. Locks into position along
length of mounting bars with locking spring and bendable slot. (3) slots 90°
apart simplify alignment.
Options & Accessories
AirSeal® Kit: LAS56 (optional)
Note: Use only if factory installed tape or knockouts are removed from vertical
adjustment slots in housing wall.
Labels
UL (Type IC Suitable for Damp Locations)
3. Junction Box: 2" X 4" X 3 1/2" (22 cu. in.) .032" (#22 ga.) galvanized steel.
UL listed for branch circuit wiring supplying connected luminaires. Integral
cable clamps permit attachment of non-metallic (#12 or #14 ga.) Romex®
cable without tools or additional connectors.
Complies with Air Leakage Requirements stated in the Model Energy Code,
California Title 24 and the Washington State Energy Code.
Romex® is a registered trademark of General Cable Industries Inc.
US and Foreign Patents Pending.
4. Mounting Bars: .059” (#16 ga.) galvanized steel. Bars pivot for easy
attachment and wire-in below ceiling line. Bars extend to accommodate 16"
to 24" O.C. joist spacing. Bars can accommodate 9" O.C. joist spacing after
a slight field modification (see Instruction Sheet). Features integral self-
tapping phillips screws for secure attachment to wood or metal construction.
Attaches to T-bar ceilings without the need of accessories.
Job Information
Type:
Job Name:
Cat. No.:
5. Socket Housing: Trim retaining spring secures trim to any height on
housing wall.
6. Socket: (4 Pin,GX24q-2) base, molded thermo-plastic. Pre-wired with #18
AWG leads to junction box.
Lamp(s):
Notes:
7. Ballast: Electronic 120V, end of life protected, FCC class “B” consumer
limits, class “A” sound rating. Energy Star® qualified.
Electrical
Input Watts: 19
Amps: .16
Ballast Factor: 1.0
Power Factor: .97
Lightolier a Genlyte company
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2006 Genlyte Group LLC • B0906
Download from Www.Somanuals.com. All Manuals Search And Download.
|