Performance Recessed CFL Downlighting
5" Aperture, 1 Light, Compact Fluorescent, IC AirSeal®, Dimming, Frame-In Kit
1001FDIC
Page 1 of 1
Overall Length
3
5
15 5/16"
12 1/4"
1
13" Min.
24" Max.
Overall Width
10 3/8"
4
Frame-in Kit
2
Height: 7 1/4"
7
6
Ceiling Opening: 5 1/4"
Reflector Trim
Top View
Complete Fixture consists of Frame-In Kit and Reflector Trim. Select each separately.
Uniframe™ Compact Fluorescent Performance Series Reflector Trims
Uniframe™
Frame-In Kit
Horizontal Open
Horizontal Wall
Wash - Single
Horizontal Wet Location
Lensed / Diffused
Horizontal
Cross Blade
1001FDICMX1**
(Advance Mark10 – 120v)
26w Triple
1001HCL
1001HCD
1001HWH
1001HCLSW
1001HCDSW
1001HWHSW
Clear Lens
1001HCLC
1001HCDC
1001HWHC
Fresnel
1001HACB
1001HWHCB
1001HCLF
1001HCDF
1001HWHF
GX24q-3 Base
120v – 0.26amp max
Opal Lens
1001FDICMX2**
(Advance Mark10 – 277v)
26w Triple
1001HCLO
1001HCDO
1001HWHO
GX24q-3 Base
277v – 0.11amp max
Universal Series Reflector Trims (Reference Trim Spec Sheet for Recommended Lamping)
Cone
Satin Cone
Baffle
Wall Wash
Wet Location
1012*
1013*
1013BK*
1013WH
1013CD*
1071
1045
1046
1046CD
1008*
1010*
1005*
1035
1035WH
1085
1095
1096
1024
1078
1005BNM
1005WH
1076
**Add N to catalog number
for preset nails.
1076WH
*Add NM suffix to catalog number
for Natural Metal flange and finish.
1096CD
Features
Options & Accessories
1. Housing: .028" (#21ga.) aluminum. UL listed for direct contact with thermal
insulation. AirSeal® housing minimizes air leakage to less than 2 CFM at 1.57
PSF (or 75pa), which complies with Model Energy Code (Section 602.3.3) and
Washington State Energy Code (Section 502.4) and reduces heat loss and
condensation in ceiling. Access door for inspection of junction box.
2. Mounting Frame: .032 (#22 ga.) galvanized steel. Accommodates ceilings
up to 1 1/2" thick. 3/8" deep integral lip. Locks into position along length
of mounting bars with locking screw and bendable slot. Four slots are
positioned 90° apart to simplify alignment. Push-in/twist-out roto-clips hold
reflector flush to ceiling.
Extra-Thick Ceiling
Mounting Ring: 1967B - 1 1/4" to 2" thick ceilings
Labels
cULus Listed (Type I.C., Suitable for Damp Location), I.B.E.W.
Complies with Air Leakage Requirements stated in the Model Energy Code and
the Washington State Energy Code.
AirSeal® is a registered trademark of Lightolier
3. Junction Box: 2" X 4" X 3 1/2" (22 cu. in) .032" (#22 ga.) galvanized steel. UL
listed for maximum of 8 (#12 ga.) 90°C through branch circuit conductors.
4. Mounting Bars: .059" (#16 ga.) galvanized steel. Bars pivot for easy
attachment and wire-in below ceiling line. Bars extend to accommodate 16"
to 24" O.C. joist spacing. Bars can accommodate 12" O.C joist spacing after
a slight field modification (see Instruction Sheet). Features integral self
tapping phillips screws for secure attachment to wood or metal construction.
Attaches to T-bar ceilings without the need of accessories.
Job Information
Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
5. Ballast: Mounted inside housing. 120V or 277V UL Listed Electronic Dimming
Ballast, end of lamp life protection, class “P” thermally protected, class “A”
sound rating.
6. Socket: Four-pin base, molded thermoplastic socket, prewired with No. 18
AWM leads to ballast.
7. Socket Housing: .036" (#20ga.) Galvanized Steel housing attaches to
reflector trim by spring clip for precise optic alignment.
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
Lightolier is a Philips group brand
Download from Www.Somanuals.com. All Manuals Search And Download.
|