95Xe Total Body Tr ainer
As s e mb l y In s t r u c t io n s
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS!
! DO NOT locate the Cross-Trainer outdoors, near swimming pools, or in areas of high
humidity.
! DO NOT operate your Cross-Trainer if it has been dropped, damaged, or even partially
immersed in water. If this occurs, contact Life Fitness Customer Support Services at the
number in the Operation Manual.
! DO NOT locate the Cross-Trainer any closer than 30 inches (76 cm ) to a television set.
! DO NOT locate additional Cross-Trainers any closer than 42 inches (107 cm) from center to
center to avoid interference (cross talk) between Heart Rate monitors.
! DO keep the area around your Cross-Trainer clear of any obstructions, including walls and
furniture. Ensure that there is at least a 12 inch (30cm) clearance in front of the Cross-
Trainer.
! DO verify the contents of the delivery carton against the accompanying Parts List prior to
setting the cartons and shipping material aside. If any parts are missing, contact Life Fitness
Customer Support Services at the number listed in the Operation Manual. Save the shipping
cartons in case of return.
! DO read the entire Operation Manual prior to attempting to operate this machine as this is
essential for proper use.
CONSIGNES DE SECURITE IMPORTANTES!
! NE placez PAS l'appareil à l'extérieur, près d'une piscine ou dans un endroit très humide.
! NE faites PAS fonctionner l'appareil s'il est tombé, s'il a été endommagé ou s'il a été.
! partiellement plongé dans l'eau. Si cela s'est produit, contactez le service après-vente de
Life Fitness au numéro fourni dans le manuel d'utilisation.
! NE placez PAS l'appareil à moins de 76 cm d'un poste de télévision.
! NE placez PAS d'autres appareils du même type à proximité. Un espace d'au moins 107 cm
doit être observé entre les parties centrales de deux appareils afin d'éviter les interférences
entre les contrôleurs de rythme cardiaque.
! MAINTENEZ la zone autour de l'appareil libre de toute obstruction, y compris murs et
meubles. Veillez à laisser un dégagement d'au moins 30 cm devant l'appareil.
! VÉRIFIEZ si l'emballage contient toutes les pièces de la liste jointe avant de le mettre de
côté. Si des pièces sont absentes, contactez le service après-vente de Life Fitness au
numéro indiqué dans le manuel d'utilisation. Conservez l'emballage au cas où vous devriez
renvoyer l'appareil.
! LISEZ le manuel de l'utilisateur tout entier avant d'essayer de faire fonctionner cet appareil.
Ceci est indispensable à son utilisation correcte.
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS REQUIRED FOR ASSEMBLY...
Magnetic #2 Bit Phillips Screwdriver, T-45 Hex Key Wrench, 16mm Open End Wrench
PARTS DESCRIPTION
1
3
Torx Socket Head Screw
M8 – 1.25 x 19
0017-00101-1791
Phillips Pan Head Screw
M4.2 – 0.70 x 10
Qty: 16
2
Phillips Pan Head Screw
M4 – 0.70 x 19
0017-00101-1796
Qty: 14
Qty: 1
Qty: 2
4
Console Assembly
0017-00101-1846
Front Rocker Cover
OK62-01009-0000
Console Support Assembly
OK62-00123-0000
Front Pivot Arm Cover
OK62-01012-0000
Left User Arm Assembly
AK62-00087-0000
Left Bullhorn
AK62-00054-0000
Left Bullhorn Cover
OK62-01008-0001
Accessory Tray
OK62-01022-0000
Base Frame Cap
5
Qty: 2
Qty: 1
Qty: 2
Qty: 1
Qty: 1
Qty: 1
Qty: 1
Qty: 1
Qty: 1
6
Left Back Rocker Cover
OK62-01011-0000
Console Support Cover
OK62-01023-0000
Rear Pivot Arm Cover
OK62-01013-0000
Right User Arm Assembly
AK62-00086-0000
Right Bullhorn
AK62-00053-0000
Right Bullhorn Cover
OK62-01007-0001
Right Back Rocker Cover
OK62-01010-0000
Foot Cover
Qty: 1
Qty: 1
Qty: 2
Qty: 1
Qty: 1
Qty: 1
Qty: 1
Qty: 4
Qty: 2
7
8
9
10
12
14
16
18
20
22
11
13
15
17
19
21
OK62-01004-0000
Cap: Console Support
OK62-01030-0000
OK62-01003-0000
Phillips Pan Head Screw
M4 – 0.70 x 44
0017-00101-1854
1
3
2
22
1”
2”
3”
4”
5”
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT! Do not discard the ship kit located on top of the pedal levers. All necessary components needed to
complete the installation are located in the ship kit.
IMPORTANT! Ne jetez pas le kit placé sur le dessus des leviers de pédale. Il contient tous les éléments nécessaires
pour l'installation.
1. Locate the LEFT HANDLEBAR (11). Position the HANDLEBAR near the top of
the LEFT PIVOT ARM (A). Connect the HEART RATE CONNECTOR (B)
leading from the HANDLEBAR to the CONNECTOR (C) extending from the top
of the LEFT PIVOT ARM. Carefully slide the excess HEART RATE CABLE into
the top of the LEFT PIVOT ARM.
Align the mounting holes of the LEFT HANDLEBAR with the mounting holes at
the top of the LEFT PIVOT ARM. Secure them together using three SCREWS
(1).
11
C
9
NOTE: Be careful not to pinch the HEART RATE CABLE when securing the
LEFT HANDLEBAR to the LEFT PIVOT ARM.
B
REMARQUE : Faites attention de ne pas coincer le CÂBLE DU MONITEUR
DE FRÉQUENCE CARDIAQUE en fixant le GUIDON GAUCHE au BRAS
MOBILE GAUCHE.
2
2. Locate one LEFT FRONT ROCKER COVER (5) and the LEFT BACK
ROCKER COVER (6). Position the LEFT BACK ROCKER COVER over the
user side of the ROCKER ARM making sure that it seats fully over the
BULLHORN MOUNTING BRACKET (D). Place the FRONT ROCKER COVER
over the opposite side of the ROCKER ARM in the same manner. Secure the
COVERS using two PHILLIPS PAN HEAD SCREWS (2). Tighten the
SCREWS securely. Do not over-tighten the SCREWS.
1
10
A
5
3. Locate one FRONT PIVOT ARM COVER (9) and one BACK PIVOT ARM
COVER (10). Position the BACK PIVOT ARM COVER over the user side of the
ROCKER ARM making sure that it interlocks with the ROCKER COVER. Place
the FRONT PIVOT ARM COVER over the opposite side of the PIVOT ARM in
the same manner. Secure the COVERS using two PHILLIPS PAN HEAD
SCREWS (2). Tighten the SCREWS securely. Do not over-tighten the
SCREWS.
D
4. Locate the LEFT BULLHORN (13). Secure the BULLHORN to THE
BULLHORN MOUNTING BRACKET (D) using two FLAT HEAD SCREWS (1).
Tighten the SCREWS securely. Locate and attach the LEFT BULLHORN
COVER (15) to the base of the BULLHORN using one SCREW (22). Tighten
the SCREW securely. Do not over-tighten the SCREW. Slide the GASKET (E)
downward to meet the BULLHORN COVER.
A
E
6
5. Repeat steps one through four to install the RIGHT ROCKER COVERS (5 &
6), PIVOT ARM COVERS (9 & 10), BULLHORN (14) and BULLHORN COVER
(16).
2
13
NOTE: The right PIVOT ARM COVERS are reversed front and back. The
SCREWS will be installed from the rear.
1
15 22
REMARQUE : Les couvercles du BRAS MOBILE DROIT sont inversés à
l'avant et à l'arrière. Les VIS sont insérées de l'arrière.
6. Unwrap the MAIN WIRE, COAXIAL CABLE and HEART RATE HARNESS
leading from the MONOCOLUMN (F). Feed the WIRE HARNESSES through
the CONSOLE SUPPORT ASSEMBLY TUBE (G) located at the top and front
of the MONOCOLUMN. Locate the CONSOLE SUPPORT ASSEMBLY (7) and
position it near the top of the MONOCOLUMN. Feed the WIRE HARNESSES
through the CONSOLE SUPPORT ASSEMBLY as shown. Align the bottom
mounting holes of the CONSOLE SUPPORT ASSEMBLY with those in the
CONSOLE SUPPORT ASSEMBLY TUBE. Secure them together using six
SCREWS (1). Tighten the SCREWS securely.
2
7
21
4
NOTE: Be careful not to damage the WIRE HARNESSES when routing it
through the CONSOLE SUPPORT ASSEMBLY or when mounting the
CONSOLE SUPPORT ASSEMBLY to the CONSOLE SUPPORT ASSEMBLY
TUBE.
17
1
REMARQUE : Faites attention de ne pas coincer les FAISCEAUX DE
CÂBLES en les insérant dans le SUPPORT DE LA CONSOLE ou en fixant le
SUPPORT DE LA CONSOLE au TUBE DE SUPPORT DE LA CONSOLE.
2
1
7. Locate the ACCESSORY TRAY (17). Slide the ACCESSORY TRAY into the
top of the MONOCOLUMN (F) as shown. Be sure the ACCESSORY TRAY is
fully seated.
8
3
NOTE: Be careful not to damage the MAIN WIRE HARNESS when sliding
G
the ACCESSORY TRAY into the MONOCOLUMN.
REMARQUE : Faites attention de ne pas endommager le FAISCEAU DE
CÂBLES PRINCIPAL en glissant le PLATEAU POUR ACCESSOIRES sur la
COLONNE MONOBLOC.
Secure the ACCESSORY TRAY to the CONSOLE SUPPORT ASSEMBLY
using two SCREWS (3). Tighten the SCREWS securely. Do not over-tighten
the SCREWS.
F
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Locate the DISPLAY CONSOLE (4). Position the CONSOLE near the
top of the CONSOLE BRACKET. Attach all CONNECTORS leading from
the CONSOLE BRACKET to their corresponding CONNECTORS in the
back of the DISPLAY CONSOLE. Feed any excess WIRE HARNESS
into the CONSOLE BRACKET and place the DISPLAY CONSOLE onto
the CONSOLE BRACKET aligning the mounting holes. Secure the
DISPLAY CONSOLE using four SCREWS (2). Tighten the SCREWS
securely. Do not over-tighten the SCREWS.
2
7
21
4
17
1
9. Locate the CONSOLE SUPPORT COVER (8). Position the CONSOLE
BRACKET COVER over the underside of the CONSOLE SUPPORT
ASSEMBLY (7) as shown and secure it using two SCREWS (2). Tighten
the SCREWS securely. Do not over-tighten the SCREWS.
2
1
10. Locate the CONSOLE SUPPORT CAP (21). Snap the CAP into position
at the top of the CONSOLE SUPPORT COVER.
11. Locate the BASE FRAME CAP (19). Remove the two SCREWS (H)
securing the front of the BASE FRAME COVER (J) to the BASE FRAME
(K). Position the CAP over the front of the BASE FRAME as shown
sliding the mounting tabs to the inside of the BASE FRAME COVER.
Secure the CAP using two SCREWS (H) previously removed. Tighten
THE SCREWS securely. Do not over-tighten the SCREWS.
8
3
G
12. Locate the four FOOT COVERS (20). Align the COVERS with the ends
of the STABILIZER BARS (L). Insert the post on the underside of the
FOOT COVERS into the mounting holes on the top of each
F
STABILIZER. Press the FOOT COVERS firmly into position.
13. With the cross-trainer in the intended location for use, locate the
supplied POWER SUPPLY (#11) and LINE CORD (#12). A coaxial
broadcast supply line with an F-Type connector (not supplied) is
required for entertainment viewing. Connect the POWER SUPPLY
CONNECTOR to the appropriate connector located on the front
underside of the cross-trainer. Connect the broadcast supply line at this
time if available. Connect the LINE CORD to the POWER SUPPLY and
plug the LINE CORD into a power outlet.
H
19
K
NOTE: Refer to the OPERATION MANUAL for specific power
requirements.
REMARQUE : Reportez-vous au GUIDE D'UTILISATION pour les
caractéristiques de l'alimentation électrique.
14. With the cross-trainer in the intended location for use, check the
stability of the cross-trainer. If the cross-trainer is not level, turn a
LEVELER (M) in the front STABILIZER BAR (L) in either direction until
the rocking motion is eliminated. Tighten the JAM NUT (N) when the
cross-trainer is level.
20
M
N
L
J
NOTE: Only one leveler needs to be turned.
REMARQUE : Ne tourner qu’un seul vérin.
12
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE-OPERATION CHECKLIST
"
"
Ensure that all fasteners are tight.
Make sure the CROSS-TRAINER is properly leveled and stable.
(Refer to the Operation Manual)
"
"
Ensure that the Leveler Jam Nuts are tight.
(Refer to the Operation Manual)
Read the entire Operation manual before using the Cross-Trainer.
LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE
"
"
Vérifiez si tous les dispositifs de fixation sont serrés
Vérifiez si l'APPAREIL D'EXERCICE POLYVALENT est de niveau et stable.
(Référez-vous au manuel d'utilisation.)
"
"
Vérifiez si les contre-écrous des vérins de mise à niveau sont serrés.
(Référez-vous au manuel d'utilisation.)
Lisez le manuel d'utilisation dans son intégralité avant d'utiliser l'appareil d'exercice polyvalent..
Before attempting to operate your Total Body Trainer, it is imperative that you familiarize yourself with the contents of
the Operation Manual. If your Total Body Trainer does not respond as described in the Operation Manual, contact the
nearest Life Fitness service center as listed in the Operation Manual.
Life Fitness Customer Support Services
(800) 351-3737 or (847) 451-0036
Prior to your call, please be sure you have located and noted the
MODEL NUMBER & SERIAL NUMBER.
The Model & Serial number information of your Life Fitness Total Body Trainer is listed on a label
located on the rear stabilizer.
©2004 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness, Lifepulse, FlexDeck and Smart Stop are
trademarks of Brunswick Corporation.
MO51-00K62-A078
04.04
Download from Www.Somanuals.com. All Manuals Search And Download.
|