8115 FLAT & INCLINE BENCH
ASSEMBLY INSTRUCTIONS
Part # 6791801
1
Revision:7/20/98
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY PART #
DESCRIPTION
REAR UPRIGHT
BENCH FRAME
ADJUSTABLE SLEEVE
BASE TUBE
QTY
KEY PART #
DESCRIPTION
1/2 X 1-1/4” BOLT
3/8 X 1-1/4” BOLT
1/2” WASHER
QTY
1
2
3
4
5
6
7
8
9
6651703
6700503
6712803
6697203
6624202
6624302
6651602
6780001
6780301
1
1
1
1
1
1
2
1
1
1
1
2
2
14 3202101
15 3102901
16 3102502
17 3102501
18 3102801
19 3102804
20 6406401
21 6619301
22 6653101
23 6412001
24 3120701
25 3118401
2
4
6
6
5
3
2
1
1
1
1
1
3/8” WASHER
LEFT BACK PAD ANGLE
RIGHT BACK PAD ANGLE
2 X 15-1/2” PLATE
SEAT PAD
1/2” LOCK NUT
1/2” LOW HEIGHT NUT
HINGE TAB
U-PIN
BACK PAD
1/2” SPACER
10 3202106
11 3202107
12 3102917
13 3102910
1/2 X 9-1/2” BOLT
1/2 X 6-1/2” BOLT
1/2 X 4” BOLT
3/8” SPRING PIN
1/2” PAL NUT
4” VINYL CAP
1/2 X 3” BOLT
24
22
2
25
21
FIGURE 1
STEP 1:
•
Assemble one U-PIN (21) to the BENCH FRAME (2) using one 1/2” SPACER (22) and one 1/2” PAL NUT (24) as shown in
FIGURE 1.
•
Slide one 4” VINYL CAP (25) onto the U-PIN (21) as shown in FIGURE 1.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3
2
23
FIGURE 2
STEP 2:
•
SECURELY assemble the 3/8” SPRING PIN (23) to the ADJUSTABLE SLEEVE (3) as shown in FIGURE 2.
•
Pull back the 3/8” SPRING PIN (23) on the ADJUSTABLE SLEEVE (3) and slide it over the end of the BENCH FRAME (2) as
shown in FIGURE 2. Slide the ADJUSTABLE SLEEVE (3) up to the first adjustment hole.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
3
4
5
2
6
4
Download from Www.Somanuals.com. All Manuals Search And Download.
13 1/2 X 3”
16
1
2
18
18
4
1/2 X 4” 12
FIGURE 3
STEP 3:
•
SECURELY assemble the REAR UPRIGHT (1) to the BENCH FRAME (2) using two 1/2 X 3” BOLTS (13), four 1/2” WASHERS
(16), and two 1/2” LOCK NUTS (18) as shown in FIGURE 3.
•
SECURELY assemble the BASE TUBE (4) to the BENCH FRAME (2) using two 1/2 X 4” BOLTS (12) and two 1/2” LOCK NUTS
(18) as shown in FIGURE 3.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
19 1/2” LOW
HEIGHT
2
5
20
1/2 X 9-1/2” 10
FIGURE 4
STEP 4:
•
Assemble the LEFT & RIGHT BACK PAD ANGLES (5 & 6) and two HINGE TABS (20) to the BENCH FRAME (2) using one 1/2
X 9-1/2” BOLT (10) and one 1/2” LOW HEIGHT LOCK NUT (19). (NOTE: Tighten connection enough to remove play yet
allowing the parts to rotate freely.) See FIGURE 4.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
3
4
5
2
6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
16
6
5
19
1/2”
LOW
HT.
14 1/2 X 1-1/4”
7
18
1/2 X 6-1/2” 11
FIGURE 5
STEP 5:
•
Assemble the LEFT & RIGHT BACK PAD ANGLES (5 & 6) and two HINGE TABS (20) to the BENCH FRAME (2) using one 1/2
X 9-1/2” BOLT (10) and one 1/2” LOW HEIGHT LOCK NUT (19). (NOTE: Tighten connection enough to remove play yet
allowing the parts to rotate freely.) See FIGURE 4.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
17
3/8 X 1-1/4” 15
9
6
5
FIGURE 6
STEP 6:
•
SECURELY assemble the BACK PAD (9) to the LEFT & RIGHT BACK PAD ANGLES (5 & 6) using four 3/8 X 1-1/4” BOLTS (15) and
four 3/8” WASHERS (17) as shown in FIGURE 6.
1/2
1/2
1/2
1/2
1/2
1/2
0
1
3
4
5
2
6
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8
20
17
3/8 X 1-1/4” 15
FIGURE 7
STEP 7:
•
SECURELY assemble the SEAT PAD (8) to the HINGE TABS (20) using two 3/8 X 1-1/4” BOLTS (15) and two 3/8” WASHERS (17) as
shown in FIGURE 7.
Thank you for purchasing the LifeFitness 8115 FLAT & INCLINE BENCH. If unsure of proper use of
equipment, call your local LifeFitness distributor or call the LifeFitness customer service department at
(800) 328-9714.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
|