INTEGRITY AND CLUB SERIES CROSS-TRAINERS
CLSX & CSX ASSEMBLY INSTRUCTIONS
M051-00K61-C131
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS!
â DO NOT locate the Cross-Trainer outdoors, near swimming pools, or in areas of high
humidity.
â DO NOT operate your Cross-Trainer if it has been dropped, damaged, or even partially
immersed in water. If this occurs, contact Life Fitness Customer Support Services at
the number in the Operation Manual.
â DO NOT locate the Cross-Trainer any closer than 30 inches (76 cm) to a television
set.
â DO NOT locate additional Cross-Trainers any closer than 42 inches (107 cm) from
center to center to avoid interference (cross talk) between heart rate monitors.
â DO keep the area around your Cross-Trainer clear of any obstructions, including walls
and furniture. Ensure that there is at least a 12 inch (30 cm) clearance in front of the
Cross-Trainer.
â DO verify the contents of the delivery carton against the accompanying parts list prior
to setting the cartons and shipping material aside. If any parts are missing, contact
Life Fitness Customer Support Service at the number listed in the operation manual.
Save the shipping cartons in case of return.
â DO read the entire Operation Manual prior to attempting to operate this machine as
this is essential for proper use.
CONSIGNES DE SECURITE IMPORTANTES!
â NE placez pas l'appareil à l'extérieur, près d'une piscine ou dans un endroit très
humide.
â NE faites pas fonctionner l'appareil s'il est tombé, s'il a été endommagé ou s'il a été
partiellement plongé dans l'eau. Si cela s'est produit, contactez le service après-vente
de life fitness au numéro fourni dans le manuel d'utilisation.
â NE placez pas l'appareil à moins de 76 cm d'un poste de télévision.
â NE placez pas d'autres appareils du même type à proximité. Un espace d'au moins
107 cm doit être observé entre les parties centrales de deux appareils afin d'éviter les
interférences entre les contrôleurs de rythme cardiaque.
â MAINTENEZ la zone autour de l'appareil libre de toute obstruction, y compris murs et
meubles. Veillez à laisser un dégagement d'au moins 30 cm devant l'appareil.
â VÉRIFIEZ si l'emballage contient toutes les pièces de la liste jointe avant de le mettre
de côté. Si des pièces sont absentes, contactez le service après-vente de life fitness
au numéro indiqué dans le manuel d'utilisation. Conservez l'emballage au cas où vous
devriez renvoyer l'appareil.
â LISEZ le manuel de l'utilisateur tout entier avant d'essayer de faire fonctionner cet
appareil. Ceci est indispensable à son utilisation correcte.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENT LIST
#
Part Description
Qty.
#
Part Description
Qty.
Hex Socket Head Cap Screw
3/8-16 X 1”
Phillips Pan Head Screw
#8-18 X 3/4”
1
8
2
4
0017-00101-1645
0017-00101-1744
Phillips Pan Head Pointed Screw
#8-18 X 3/4”
0017- 00101-1242
Console Assembly
(shipped separately)
3
5
18
1
4
6
1
1
Front Monocolumn Cover
Back Monocolumn Cover
Flat Washer
0017-00104-0192
7
9
Console Support Assembly
Left Front Cover
1
1
1
8
2
1
1
10
12
Right Front Cover
11
Left User Arm Assembly
Right User Arm Assembly
13
17
19
21
23
Front Rocker Cover
Accessory Tray
2
1
1
4
1
14
18
20
22
Back Rocker Cover
2
6
4
1
Internal Tooth Lock Washer
0017-00104-0450
Grommet
0017-00042-0754
Cap: Console Support
Cap Screw T-27
0017-00101-1746
Cup
Pad
Tools Required for Assembly
l
Magnetic #2 Bit Phillips Screwdriver
l
l
5/16” Hex Key Wrench
T-27 Torx Key Wrench
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE
FLAT WASHER (#8)
INTERNAL TOOTH LOCK WASHER (#18)
#8-18 X 3/4”PHILLIPS PAN HEAD
POINTED SCREW (#3)
#8 -18 X 10 PHILLIPS PAN HEAD SCREW (#2)
3/8 -16 X 1” HEX SOCKET HEAD CAP SCREW (#1)
GROMMET (#20)
CAP SCREW T -27 (#21)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT!
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE PEDAL LEVERS. ALL NECESSARY COMPONENTS
NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.
IMPORTANTES!
NE JETEZ PAS LE KIT PLACÉ SUR LE DESSUS DES LEVIERS DE PÉDALE. IL CONTIENT TOUS LES ÉLÉMENTS
NÉCESSAIRES POUR L'INSTALLATION.
1. Before proceeding, familiarize yourself with the parts of the
Cross-Trainer and make sure that you have received all the
items described in the Component List.
3
9
2. Locate the left and right FRONT COVER (9 &10). Using two
PHILLIPS PAN HEAD POINTED SCREWS (3), mount the LEFT FRONT
COVER (9) to the FRAME (A). Attach the RIGHT FRONT COVER (10)
to the FRAME in the same manner using two PHILLIPS PAN HEAD
POINTED SCREWS (3). Secure the tops of the FRONT COVERS
together using two PHILLIPS PAN HEAD POINTED SCREWS (3).
3
A
10
CAUTION: Do not overtighten the PHILLIPS PAN HEAD POINTED
SCREWS (3).
3. Locate the RIGHT USER ARM (12). Snap the 2-PIN CONNECTOR
(2PA) located at the bottom of the RIGHT USER ARM into the 2-
PIN CONNECTOR (2PB) positioned at the top of the RIGHT ROCKER
ARM (B). Feed the connectors and excess cable up into the
RIGHT USER ARM. Secure the RIGHT USER ARM to the RIGHT
ROCKER ARM using three HEX SOCKET HEAD CAP SCREWS (1) and
three INTERNAL TOOTH LOCK WASHERS (18). Repeat the procedure
for the LEFT USER ARM (11) and LEFT ROCKER ARM (C). Tighten
all screws securely.
12
11
18
1
CAUTION: Be careful not to pinch the WIRE HARNESSES when
assembling the USER ARMS (11 &12) to the ROCKER ARMS (B &
C).
2PA
2PB
4. Detach and unwrap the WIRE HARNESS (E) (16P, 4P) located at
the top of the MONOCOLUMN (F). Holding the CONSOLE SUPPORT
ASSEMBLY (7) with the handgrips facing upward, feed the WIRE
HARNESS up through the neck and out the top access hole.
Carefully lower the CONSOLE SUPPORT ASSEMBLY into the
MONOCOLUMN.
C
B
4P
16P
CAUTION: Be careful not to pinch the WIRE HARNESSES (E)
when assembling the CONSOLE SUPPORT ASSEMBLY (7) to the
MONOCOLUMN (F).
4
21
19
5. Using two HEX SOCKET HEAD CAP SCREWS (1) and two FLAT
WASHERS (8), secure the CONSOLE SUPPORT ASSEMBLY (7) to the
MONOCOLUMN (F). Tighten the SCREWS securely.
23
6. Insert the GROMMETS (20) into the four holes on the CONSOLE
SUPPORT ASSEMBLY. Locate the ACCESSORY TRAY (17). Align the
ACCESSORY TRAY with the four holes on the CONSOLE SUPPORT
ASSEMBLY. Using four PHILLIPS PAN HEAD POINTED SCREWS (3),
secure the ACCESSORY TRAY to the CONSOLE SUPPORT ASSEMBLY
as shown. Tighten the SCREWS securely.
2
7
22
3
17
20
E
CAUTION: Do not overtighten the PHILLIPS PAN HEAD POINTED
SCREWS (3).
1
8
7. Remove the adhesive back and install the PAD (23). Install
the CUP (22).
F
5
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Attach the 4-PIN (4P) and 16-PIN (16P) CONNECTORS to the
corresponding JACKS on the back of the CONSOLE ASSEMBLY (4).
4P
16P
9. Feed any excess WIRE HARNESS (E) down into the CONSOLE
SUPPORT ASSEMBLY (7). Secure the CONSOLE ASSEMBLY (4) to the
CONSOLE SUPPORT ASSEMBLY using four PHILLIPS PAN HEAD
SCREWS (2). Tighten the SCREWS securely.
4
21
19
CAUTION: Do not over-tighten the PHILLIPS PAN HEAD
SCREWS (2).
23
CAUTION: Be careful not to pinch the WIRE HARNESS (E) when
assembling the CONSOLE ASSEMBLY (4) to the CONSOLE SUPPORT
ASSEMBLY (7).
2
7
22
3
10. Locate and install the CONSOLE SUPPORT CAP (19) onto the
CONSOLE SUPPORT ASSEMBLY (7) as shown using four CAP
SCREWS (21).
17
20
E
1
8
11. Place the BACK MONOCOLUMN COVER (6) over the PIVOT SHAFT (H)
at the top of the MONOCOLUMN (F).
12. Place the FRONT MONOCOLUMN COVER (5) on the opposite side of
the BACK MONOCOLUMN COVER (6) to cover the PIVOT SHAFT (G)
and CONSOLE SUPPORT ASSEMBLY MOUNTING SCREWS. Interlock the
top tabs and use two PHILLIPS PAN HEAD POINTED SCREWS (3) to
secure the bottoms of the MONOCOLUMN COVERS together.
Tighten the SCREWS securely.
F
CAUTION: Do not over-tighten the PHILLIPS PAN HEAD POINTED
SCREWS (3).
13. Locate one FRONT ROCKER COVER (13) and one BACK ROCKER
COVER (14). Position the FRONT ROCKER COVER over the user
side of the left end of the PIVOT SHAFT (H) (as shown) making
sure that it interlocks with the MONOCOLUMN COVERS (5 & 6).
Place the BACK ROCKER COVER over the opposite side of the left
end of the PIVOT SHAFT in the same manner. Secure the COVERS
using three PHILLIPS PAN HEAD POINTED SCREWS (3). Repeat the
procedure reversing front and back for the user right end of the
PIVOT SHAFT.
13
5
G
14
H
6
3
14
F
CAUTION: Do not over-tighten the PHILLIPS PAN HEAD POINTED
SCREWS (3).
13
3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE-OPERATION CHECKLIST
3 Ensure that all fasteners are tight.
3 Make sure the Cross-Trainer is properly leveled and stable.
(Refer to the Cross-Trainer model’s corresponding Operation Manual.)
3 Ensure that the Leveler Jam Nuts are tight. (Refer to the Cross-Trainer model’s corresponding Operation Manual.)
3 Read the entire Operation Manual before using the Cross-Trainer.
LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE
3 Vérifiez si tous les dispositifs de fixation sont serrés
3 Vérifiez si l'APPAREIL D'EXERCICE POLYVALENT est de niveau et stable.(Référez-vous au manuel d'utilisation.)
3 Vérifiez si les contre-écrous des vérins de mise à niveau sont serrés.(Référez-vous au manuel d'utilisation.)
3 Lisez le manuel d'utilisation dans son intégralité avant d'utiliser l'appareil d'exercice polyvalent.
Before attempting to operate your Cross-Trainer, it is imperative that you familiarize yourself with the contents of the
Operation Manual. If your Cross-Trainer does not behave as described in the OPERATION MANUAL contact Life
Fitness Customer Support Services at 800.735.3867 (toll-free within U.S.A., Canada). Refer to the OPERATION
MANUAL for a contact list of International Offices. Prior to your call, please be sure you have located and noted the
MODEL NUMBER & SERIAL NUMBER. The Model & Serial number information of your Life Fitness Cross-Trainer is
listed on a label located on the front stabilizer.
Physical Dimensions
Length:
81 3⁄
in. (207.65 cm.)
4
Width:
28 in. (71.12 cm.)
Height:
65 in. (165 cm.) with console
239 lbs. (108.41 kg.)
232 lbs. (105.24 kg.)
Weight (CLSX):
Weight (CSX):
243 lbs. (110.22 kg.) with console
236 lbs. (107.05 kg.) with console
Shipping Dimensions (without console)
Length:
80 in. (203 cm.)
28 in. (71 cm.)
Width:
Height:
47.5 in. (121 cm.)
303 lbs. (137 kg.)
296 lbs. (134.27 kg.)
Weight (CLSX):
Weight (CSX):
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|