LIFE FITNESS EXERCISE BIKE
INSTALLATION INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS REQUIRED FOR ASSEMBLY... Phillips screwdriver, 1/2” wrench
PARTS DESCRIPTION
STABILIZER/HANDLEBAR BOLT Qty: 5
CONSOLE SCREW
Qty: 4
Qty: 1
Qty: 1
Qty: 1
1
3
5
7
2
4
6
8
0017-00101-1043
0017-00101-0932
COLLAR
SEAT ASSEMBLY
Qty: 1
Qty: 1
Qty: 1
AK18-00127-0002
HANDLEBAR ASSEMBLY
0K18-01156-0001
DISPLAY CONSOLE ASSEMBLY
AK18-00168-0000
STABILIZER BAR
AK17-00206-0001
9V ALKALINE BATTERY
AK18-0070-0000
0017-00003-0757
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1
Before proceeding, familiarize yourself with the parts of the Lifecycle 8500 exercise bike and make sure that you
have received all the items described in the Parts List.
Step 2
Remove the STABILIZER BAR (#7) from the
carton base. Use the empty CONSOLE
CARTON (A) to raise the rear of the Lifecycle
bike as shown.
Remove the two BOLTS (#1) from the bottom
of the SHIPPING STABILIZER (B), save the
BOLTS and store the SHIPPING STABILIZER
with the other shipping containers.
Step 3
Use the same two BOLTS that held the
SHIPPING STABILIZER in place to attach the
STABILIZER BAR as shown. Make certain
that the BOLTS are very tight and the
STABILIZER BAR is flush against the frame.
Remove the shipping carton.
Step 4
Unfold the CONSOLE WIRE HARNESS (C)
from the HANDLEBAR POST extending from
the FRAME.
NOTE: THE COLLAR (#4) SHOULD ALREADY BE IN PLACE INSTALLED ON THE
HANDLEBAR ASSEMBLY (#5). IF NOT, INSTALL BEFORE PROCEEDING.
Step 5
Place the HANDLEBAR ASSEMBLY on the floor in front of the
FRAME with the two CONNECTORS (10P) next to each other.
Align the two CONNECTORS with each other and firmly push
them together until they snap into place.
Step 6
Position the HANDLEBAR ASSEMBLY, with the COLLAR (#4)
in place, so that the HANDLEBAR is facing away from the seat.
Slide the HANDLEBAR ASSEMBLY into the HANDLEBAR
POST (D). Be careful not to pinch the wires.
Align the three holes in
the HANDLEBAR
ASSEMBLY with those
in the HANDLEBAR
POST and install the
three HANDLEBAR
BOLTS (#1).
NOTE: BE CAREFUL NOT TO DAMAGE THE WIRES WHEN PASSING
THE BOLTS THROUGH THE HOLES. TIGHTEN THE BOLTS
SECURELY.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7
Slide the COLLAR (#4) down until it completely covers the
HANDLEBAR ASSEMBLY HARDWARE and the HANDLEBAR
POST (D). Secure the COLLAR by squeezing the sides and
pushing firmly downward.
Step 8
There is a large hole in the rear of the DISPLAY CONSOLE
(#6) through which you can see a 16-PIN CONNECTOR (16P)
and a 3-PIN CONNECTOR (3P). These correspond to the
respective CONNECTORS on the WIRE HARNESS protruding
from the top of the HANDLEBAR.
Properly align the locking tabs of the 16-PIN
CONNECTOR (16P) on the WIRE HARNESS with the 16-
PIN CONNECTOR on the back of the DISPLAY
CONSOLE, then snap them together. Next, align the
locking tabs of the 3-PIN CONNECTOR (3P) on the WIRE
HARNESS with the 3-PIN on the back of the DISPLAY
CONSOLE and push them together until they SNAP into
place.
Step 9
Feed the WIRE HARNESS back into the HANDLEBAR
TUBE. Attach the DISPLAY CONSOLE to the
HANDLEBAR ASSEMBLY using the four CONSOLE
SCREWS (#2) and a Phillips screwdriver. Tighten the four
SCREWS in a crisscross pattern.
1
2
4
2
CAUTION!: BE CAREFUL NOT TO OVERTIGHTEN THE SCREWS.
Step 10
To install the 9-VOLT ALKALINE BATTERY (#8) found in the parts bag use a Phillips screwdriver to remove the
screw from the BATTERY DOOR (E). Gently pull the BATTERY WIRES (F) from the back of the DISPLAY
CONSOLE and connect them to
NOTE: ONLY USE AN ALKALINE TYPE BATTERY. USE OF ANY OTHER TYPE
the 9-VOLT ALKALINE BATTERY.
BATTERY MAY RESULT IN A MALFUNCTION OR DAMAGE.
Carefully, tuck the BATTERY
WIRES back into the DISPLAY
CONSOLE and set the BATTERY
in place.
Re-install the BATTERY DOOR by
inserting the bottom tab of the
BATTERY DOOR into the
corresponding slot in the DISPLAY
CONSOLE. Push the DOOR into
place and tighten the screw with a
Phillips screwdriver.
CAUTION!: BE CAREFUL NOT TO OVER TIGHTEN THE SCREW
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 11
After placing the Lifecycle bike in the intended location for use, check the
stability of the bike.
If the bike is not stable, rotate the FOOT (G) in the STABILIZER BAR (#7)
that appears to be higher until the Lifecycle bike is stable.
Secure the position of the FOOT by tightening the LOCKNUT with an open-
end wrench.
PRE-OPERATION CHECKLIST
4 Insure that the STABILIZER BAR and HANDLEBAR BOLTS are tight.
4 Make sure the exercise bike is properly leveled and stable.
Before attempting to operate your Lifecycle 8500 exercise bike, it is imperative that you familiarize yourself with the
contents of the Operation Manual. If your exercise bike does not respond as described in the OPERATION MANUAL
contact the nearest Life Fitness Service Center as listed in the OPERATION MANUAL.
Copyright 1997 Brunswick Corporation. All rights reserved. Life Fitness and Lifecycle are trademarks of Brunswick Corporation.
M051-00K20-A052
8/97
Download from Www.Somanuals.com. All Manuals Search And Download.
|