Life Fitness Bicycle Upright Exercise Bikes User Manual

Life Fitness Upright Exercise Bikes  
How To:… INSTALL THE NETWORK OPTION  
Tools Required: Phillips screwdriver  
WARNING:  
IT IS IMPORTANT TO BE PROPERLY GROUNDED WHEN HANDLING PRINTED CIRCUIT BOARDS. BE SURE  
TO TOUCH A GROUNDED METAL OBJECT TO DISCHARGE STATIC OR INSTALL AN ANTI-STATIC CORD  
BEFORE HANDLING THE PRINTED CIRCUIT BOARDS WITHIN THE DISPLAY CONSOLE.  
1. Remove the four MOUNTING SCREWS (A) securing the REAR  
CONSOLE ASSEMBLY (B) to the DISPLAY CONSOLE MOUNTING  
BRACKET. Set the MOUNTING SCREWS aside.  
D
2. Disconnect all CONNECTORS from the rear of the DISPLAY  
B
CONSOLE.  
3. Remove the eight MOUNTING SCREWS (C) securing the OVERLAY  
BEZEL (D) to the REAR CONSOLE ASSEMBLY. Carefully remove the  
OVERLAY BEZEL from the REAR CONSOLE ASSEMBLY.  
C
4. Locate the supplied NETWORKING BOARD (E) and four plastic  
STAND-OFFS (F). Insert the STAND-OFFS in the four holes located at  
the corners of the NETWORKING BOARD. Be sure the STAND-OFFS  
snap securely into the NETWORKING BOARD.  
A
NOTE: BE SURE THE STAND-OFFS (F) ARE INSTALLED OPPOSITE  
THE NETWORK JACK (G) AS SHOWN.  
5. Position the NETWORKING BOARD (E) and STAND-OFFS (F) with the  
7-PIN NETWORK HEADER (H) aligned with the CONNECTOR PINS  
(J) and the NETWORK JACK facing the bottom of the OVERLAY  
BEZEL (D). Carefully mate the 7-PIN NETWORK HEADER with the CONNECTOR PINS and snap the STAND-OFFS into  
the MAIN CIRCUIT BOARD (K).  
CAUTION: DO NOT ATTEMPT TO SNAP ALL FOUR STAND-OFFS (F) INTO THE MAIN CIRCUIT BOARD (H)  
SIMULTANEOUSLY. POSITION THE STAND-OFFS OVER THE HOLES AND SNAP THEM INTO THE MAIN CIRCUIT  
BOARD ONE AT A TIME.  
NOTE: BE SURE NOT TO DAMAGE THE CONNECTOR PINS (J) WHEN INSTALLING THE NETWORKING BOARD (E)TO  
THE MAIN CIRCUIT BOARD (K)  
6. Connect one end of the supplied NETWORK CABLE (L) into the  
D
K
NETWORK JACK (G) on the NETWORKING BOARD (E).  
G
E
7. Remove the BATTERY DOOR from the REAR CONSOLE ASSEMBLY  
(B). Route the free end of the NETWORK CABLE (L) through the  
LARGE BATTERY DOOR ACCESS HOLE. Lower the OVERLAY  
BEZEL (D) onto the REAR CONSOLE ASSEMBLY. Secure the  
OVERLAY BEZEL to the REAR CONSOLE ASSEMBLY using the  
eight previously removed MOUNTING SCREWS (C) . Tighten the  
screws securely.  
L
NOTE: DO NOT OVER TIGHTEN THE MOUNTING SCREWS (C).  
F
8. Place the new supplied battery door into location on the REAR  
CONSOLE ASSEMBLY (B).  
H
J
9. Re-connect all CONNECTORS to the DISPLAY CONSOLE. Replace  
the REAR CONSOLE ASSEMBLY (B) to the DISPLAY CONSOLE  
MOUNTING BRACKET. Secure using the four previously removed  
MOUNTING SCREWS (A). Tighten the screws securely.  
NOTE: BE CAREFUL NOT TO PINCH ANY WIRES WHEN INSTALLING THE DISPLAY CONSOLE TO  
THE DISPLAY CONSOLE MOUNTING PLATE.  
NOTE: DO NOT OVER TIGHTEN THE MOUNTING SCREWS (A).  
10. Route the NETWORK CABLE (L) toward the MONOCOLUMN and secure using the supplied WIRE TIES.  
11. Connect the single connector end of the supplied NETWORK CONNECTOR SPLITTER to the free end of the NETWORK  
CABLE (L).  
M051-00K63-A030  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Krell Industries Stereo System MASTER REFERENCE SUBWOOFER User Manual
La Crosse Technology Portable Radio WA 1140U User Manual
Laser Digital Photo Frame AO DPF10WD User Manual
Lennox Hearth Indoor Fireplace X FIRES WS LP User Manual
Lightwave Communications Switch USB Wizard User Manual
Linear Satellite Radio ET 2 User Manual
Linksys Network Router WRT120N User Manual
Melissa Microwave Oven 653 122 User Manual
Memorex MP3 Player MPD8846 User Manual
Metabo Saw ASE 18 User Manual