Installation instructions
for NoFrost combined refrigerator-freezers
7083 461-00
ECBN 5066
Download from Www.Somanuals.com. All Manuals Search And Download.
Appliance dimensions
Installation dimensions
The location of the socket can within a radius of 2000 mm from
the appliance top center.
A = 76 mm
B = 2027 mm
C = 757 mm
D = 610 mm
E = 1413 mm
F = 952 mm
This type of dimension
line indicates the height
measuredfromthefloor.
The ice maker is fitted in the freezer compartment of the combined
refrigerator-freezer. It must be connected to the mains water sup-
ply to work.
The water shut-off valve must be positioned within the areas
marked in grey.
Important
Do not install the shut-off valve behind the appliance.
WARNING!
The water shut-off valve must not sit directly above the
socket!
Thegapbetweenthewatershut-offvalveandthesocket
mustcomplywiththeregulationsofthecountryinwhich
the appliance is used!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the anti-tipping device
WARNING!
Mounting options
Mounting the bracket with the wall studs.
Mounting with plugs to concrete walls.
The supplied anti-tipping bracket must be installed in all
cases. This prevents the appliance from tipping over when
the fully loaded door is opened.
3 Screws 6 x 60 mm
CAUTION!
Ensure that there are no electric cables or water pipes in the
wallsectiontowhichtheanti-tippingbracketistobesecured.
These could be damaged during installation.
Mounting with the wall plate turning in
the screws at an angle.
3 Screws 6 x 60 mm
Installation:
1. Mark the centre line of the appliance on the floor.
Align the anti-tipping bracket centre to the centre line.
2. Dependingontheconstitutionofthefloorandwall,useanypos-
sible mounting option as shown in chapter Mounting Options.
The screws (6 x 60) are supplied with the accessory pack.
Important!
If the floor slopes down sideways, the anti-tipping
bracket must be fitted horizontally. Lay down spacers
in the appropriate positions.
Mounting with wooden floors.
Mounting with plugs to concrete floors.
3 Screws 6 x 60 mm
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection to the water supply
Installation
1. Place the appliance in front of the installation recess.
Safety instructions and warnings
• Donotconnecttothewatersupplywhilethecombinedrefrigerator-
freezer is connected to the electricity supply.
2. Apply cover strips above, bet-
ween and below the securing
plates on the side walls of the
appliance.
• The connection to the mains water supply may only be
made by trained personnel.
Cutthecoverstripstotheright
length for this purpose.
• The water quality must comply with the drinking water
directives of the country in which the appliance is used.
Fit the adhesive cover strips
leavingagapof6,5mmtoeach
securing plate. This ensures
• The ice maker is designed exclusively to make ice cubes in
quantities required by a household and may only be operated
with water suitable for this purpose.
problem-freefittingofthecov-
2.
• All repairs and work on the ice maker may only be carried out by
ers.
customer service personnel or other trained personnel.
• Themanufacturercannotacceptliabilityfordamagecaused
by a faulty connection to the mains water supply.
Water pressure
The water pressure must be between 0.15 and 0.6 MPa (1.5 -
6 bar).
Important:
If the water filter is inserted in the appliance, the water
pressure must lie between 0.3 and 0.6 MPa (3 - 6 bar).
If the water pressure with the inserted water filter is too low,
this may cause the ice maker to malfunction.
The water supply to the appli-
ance must be through a cold
water pipe that can withstand
theoperatingpressureandcom-
plies with the hygiene regula-
tions. For this, use the stainless
steelhosesupplied(length3 m).
3. Insert the bent section of the hose
through the opening at the right side
of the appliance.
3.
4. Move the hose to the front and con-
nect with the valve connector.
Be sure the connection is tightly
arranged.
Valve connector
4.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Push the appliance slowly into the recess until the compressor
5. Locate the water hose into the rail of
mounting plate touches the anti-tipping bracket.
the appliance base.
5.
8.
6. Route the mains cable towards the socket.
7. Route the water hose towards the water shut-off tap.
WARNING!
Do not connect the appliance to the power supply until the
installation is completed.
9. Fill the hose with water and connect to the shut-off tap.
Be sure the connection is tightly arranged.
CAUTION!
Open the shut-off tap and check the system for leakage.
Lay the mains cable and the water hose in such a way that
they will not be damaged when the appliance is slid into
the installation recess.
Important!
After the ice maker has been switched on, the water supply system
must be bled. See the section Bleeding the ice maker in the
operating instructions.
6.
7.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Leveling the appliance
Adjusting the refrigerator door
1. Adjust the height of the appliance at the front by twisting the
The lateral tilt of the refrigerator door can be adjusted if required.
1
leveling feet
. Use the open-ended spanner provided.
1
2
Undo screws
. Adjust the lateral tilt using the grub screw
Turn the spanner counterclockwise to raise the appliance front
and clockwise to lower it.
(Allen key A/F 2.5).
).
1
Position the spanner accordingly(
2. Adjust the height of the appliance at the rear by turning the ad-
2
justing bolts
provided.
. Use a 1/4" box spanner or the Torx 25 wrench
1
3. Rotate leveling feet
until firmly in place against the floor.
WARNING!
Topreventtheappliancefromtippingforwardthelevel-
1
ing feet
must have contact with the floor.
Adjusting the front of the drawer
If required, the front of the freezer drawers can be adjusted.
Transfer the screws shown in the illustration (on the left and right
sides of the freezer drawer) individually to the long slots below.
Tighten the screws in the front of the drawer once it is in the right
position.
Fastening the appliance in the recess
Side view of the freezer drawer
pulled out
Once in the recess, secure the appliance to
the body of the unit using the securing
plates (4 x 16 screws).
Then click the covers sup-
plied into place.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the ventilation grille
5. Insert the locking pins to block the sup-
Pull out the bottom freezer drawer.
ports.
1. Remove the blue protection film from the dust filter
provided and insert the filter into its opening
in the plinth. Engage the filter at the
bottom, press down the button
and click into place.
5.
1.
6. Install the ventilation grille.
The grille has bolts on the inside (see detail in the drawing
below). These bolts must be inserted into the holes of the
supports.
2. Remove the locking pins of
both supports. The supports
are provided with the appli-
ance accessory pack.
2.
6.
3. Insert the supports for the ventilation grille
on the left and right sides in the motor
compartment.
7. Adjust the height of the ventilation grille.
3.
•
Loosen the grub screws at the front of the grille (Allen key
A/F 2.5).
•
•
Adjust the ventilation grille to the desired height.
Tighten the grub screws.
4. The front edge of the brackets
is flush with the front of the
ventilation grille.
Adjustthesupportsaccordingly.
7.
4.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Before fitting the door panels
Panel dimensions
Min. panel thickness = 16 mm
Max. panel thickness = 19 mm
1
Remove the cover
and unscrew the top and bottom attach-
2
ment brackets
from the refrigerator door. These attachment
brackets will be mounted onto the refrigerator door panel.
Maximum panel weight
Refrigerator panel = 27 kg
Important!
Freezer drawer panel = 10 kg
The securing nuts are needed for re-mounting the pre-
assembled door panel onto the refrigerator door.
3
Unscrew the attachment brackets
from the freezer drawers.
Theseattachmentbracketswillbemountedontothefreezerpanels.
Important!
The screws are needed for re-mounting the pre-assembled
freezer panels onto the freezer drawers.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the attachment brackets onto the door panels
1. Draw a line 1041 mm from the bottom side of the door panel.
2. Draw a further line 107.5 mm from the bottom side of the door panel.
3. Align one of the refrigerator door attachment brackets to the top line, as shown in the illustration below, and secure with at least
6 screws (4 x 14).
4. Align the second refrigerator door attachment bracket to the bottom line, as shown in the illustration below, and secure with at
least 6 screws (4 x 14).
5. Secure each of the attachment brackets that have been removed from the freezer drawers using 3 screws (4 x 14), as shown in
the illustration below.
Refrigerator door panel
Freezer drawer panel
Freezer drawer panel
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the refrigerator panel
1. Screw in the adjusting pins on the underside of the refrigerator
4. Close the refrigerator door and check the height of the panel.
door completely (fig. A).
5. Adjust the height of the panel if necessary. Undo the securing
nuts and use the adjusting pins to adjust (fig. C).
fig. C
fig. A
6. Adjust the panel horizontally (using the long slots in the attach-
ment bracket) (fig. D).
7. Tighten the securing nuts.
2. Open the refrigerator door and suspend the refrigerator panel
on the top adjusting pins (fig. B).
3. Screwsecuringnutsontotheadjustingpinsandslightlytighten.
fig. B
fig. D
11
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Undo the three screws on the top of the attachment bracket,
adjust the door panel as displayed in fig. G and then retighten
the screws. The same procedure can be carried out for the
bottom attachment bracket.
8. Remove the adjusting pins (bottom of the refrigerator door)
until these touch the attachment bracket (fig. E).
fig. E
fig. G
9. Screw on the securing nuts and tighten (fig. F).
11. Click the top and bottom covers into place
2
1
(fig. H)
Insert the cover strip provided
and panel.
between refrigerator door
fig. F
fig. H
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the freezer panels
1. Pulloutthetopfreezerdrawerandscrewonthepre-assembled
panel. The same screws must be used as those used to screw
on the attachment brackets (3.5 x 13).
2. Close the freezer drawer and check the position of the panel.
Adjust the height of the panel by undoing the left and right
screws. Tighten the screws.
3. Pull out the bottom freezer drawer and mount the panel in the
same way.
4. For both drawers, cover the gap between the drawer and the
panel with the cover strips supplied. Remove the protective
film from the trim and insert into the gap at the top.
3.5 x 13 mm
Changing over door hinges
Door hinges should only be changed by a trained expert.
WARNING!
Do not try to change over the door hinges yourself. The
refrigerator door hinges are fitted with strong closing
springs. If the hinge accidentally snaps shut, this can lead
to serious injury.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|