Liebherr Kitchen Entertainment Center 7083 103 00 User Manual

Installation instructions  
for NoFrost combined refrigerator-freezers  
7083 103-00  
ECBN 62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation dimensions  
The socket must be positioned within the areas marked in grey  
or above the installation recess.  
The ice maker is fitted in the freezer compartment of the com-  
bined refrigerator-freezer. It must be connected to the mains  
water supply to work.  
Thewatershut-offtapmustbepositionedwithintheareasmarked  
in grey.  
WARNING!  
The water shut-off tap must not sit directly  
above the socket!  
The gap between the water shut-off tap and  
the socket must comply with the regulations  
ofthecountryinwhichtheapplianceisused!  
Cabinet depth D  
625 mm + panel thickness > Inset installation style  
625 mm > Frameless installation style  
Explanation of "Installation styles" see page 4.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Definition of Inset Installation Style  
Definition of Frameless Installation Style  
Appliance and panels sit fully within the opening and are flush  
with what could be its own box, between two pantry cabinets or  
decorative columns.  
With this installation style, these wider appliance panels partially  
overlay the shared side gables of adjacent cabinetry so as to  
mimic the look of a frameless style cabinet.  
Side view of cabinet (sectional view)  
Side view of cabinet (sectional view)  
Cabinet frame  
Cabinet frame  
Door panel  
Door panel  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Panel dimensions - Inset installation style  
Paneldimensions-Framelessinstallationstyle  
Min. panel thickness = 16 mm  
Max. panel thickness = 19 mm  
Maximum panel weight  
Refrigerator panel = 12 kg  
Freezer drawer panel = 10 kg  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Door swing clearance - Inset Installation Style  
Right side wall of appliance housing  
Front of  
appliance housing  
Top View  
Panel  
thickness  
Front panel - door closed  
Panel  
thickness  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Door swing clearance - Frameless Installation Style  
Right side wall of appliance housing  
Front of  
appliance housing  
Top View  
Panel  
thickness  
Front panel - door closed  
Panel  
thickness  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting the anti-tipping device  
WARNING!  
Connection to the water supply  
Safety instructions and warnings  
The supplied anti-tipping bracket must be installed in all  
cases. This prevents the appliance from tipping over when  
the fully loaded door is opened.  
• Do not connect to the water supply while the combined refrig-  
erator-freezer is connected to the electricity supply.  
The connection to the mains water supply may only be  
made by trained personnel.  
CAUTION!  
The water quality must comply with the drinking water  
Ensure that there are no electric cables or water pipes in  
the wall section to which the anti-tipping bracket is to be  
secured. These could be damaged during installation.  
directives of the country in which the appliance is used.  
• The ice maker is designed exclusively to make ice cubes in  
quantities required by a household and may only be operated  
with water suitable for this purpose.  
Important!  
• All repairs and work on the ice maker may only be carried out  
by customer service personnel or other trained personnel.  
When securing the anti-tipping bracket to a concrete floor,  
use suitable plugs!  
The manufacturer cannot accept liability for damage  
If the floor slopes down sideways, the anti-tipping  
bracket must be fitted horizontally. Lay down spacers  
in the appropriate positions.  
caused by a faulty connection to the mains water supply.  
Water pressure  
1. Mark the centre line of the appliance on  
the floor. Align the anti-tipping bracket  
centre to the centre line.  
The water pressure must be between 150 and  
600 KPa (1.5 - 6 bar).  
Important!  
If the water filter  
isinsertedintheappliance,thewaterpressure  
must lie between 300 and 600 KPa (3 - 6 bar).  
Wall  
If the water pressure with the inserted water  
filter is too low, this may cause the ice maker to  
malfunction.  
The water supply to the appli-  
ance must be through a cold  
water pipe that can withstand  
the operating pressure and  
complies with the hygiene  
regulations.  
2. Secure the anti-tipping bracket  
to the floor using the 3 screws  
(6 mm x 60 mm) included in the  
accessory pack.  
For this, use the stainless steel hose supplied (length 3 m).  
The distance E between the leading edge of the body of the unit  
and the rear edge of the anti-tipping bracket is  
Inset installation style > 610 mm + panel thickness  
Frameless installation style > 610 mm  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
1. Place the appliance in front of the  
installation recess.  
2. Apply cover strips on the  
side walls of the appli-  
ance.  
5. Route the mains cable  
towards the socket.  
5.  
6.  
6. Route the water hose  
towards the water shut-  
off tap.  
WARNING!  
Do not connect the appliance to the power supply until the  
installation is completed.  
CAUTION!  
Lay the mains cable and the water hose in such a way  
that they will not be damaged when the appliance is slid  
into the installation recess.  
7. Push the appliance slowly into the recess until the compressor  
mounting plate touches the anti-tipping bracket.  
3. Insert the bent section of the hose through  
the opening at the rear of the appliance.  
WARNING!  
To prevent the appliance from tipping forwards, the com-  
pressor mounting plate must be touching the anti-tipping  
bracket!  
Wall  
Appliance  
4. Connect the hose to the solenoid valve  
at the front side of the appliance.  
Anti-tipping bracket  
Compressor mounting  
plate  
8. Connect the hose to the shut-off tap.  
Open the shut-off tap and check the system for leakage.  
Important!  
Aftertheicemakerhasbeenswitchedon,thewatersupplysystem  
must be bled. See the section Bleeding the ice maker in the  
operating instructions.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Levelling the appliance  
Fasten the appliance in the recess  
1. Adjust the height of the  
appliance at the front by  
twisting the adjustable  
1
feet  
(A/F 27). Use  
theopen-endedspanner  
provided.  
Fasten the appliance in the  
recess through the upper and  
lower hinges of the refrigerator  
doors.  
Caution!  
The front feet of the ap-  
pliance must be firmly  
placed on the floor.  
Use 2 screws for each hinge.  
screws  
(4 x 16 mm)  
Before fitting the door panels  
1
2
Remove the cover  
and unscrew the attachment bracket  
from the refrigerator doors. These attachment brackets will be  
mounted onto the refrigerator door panels.  
2. Adjusttheheightoftheappliance  
attherearbyturningtheadjusting  
2
bars  
.
Important!  
The securing nuts are needed for re-mounting the pre-  
assembled door panels onto the refrigerator doors.  
Turn the adjusting bars clock-  
wiseuntilthecompressormount-  
ingplatetouchestheanti-tipping  
bracket.  
Adjusting the front of the drawer  
If required, the front of the freezer drawers can be adjusted.  
Transfer the screws shown in the illustration (on the left and right  
sides of the freezer drawer) individually to the long slots below.  
Tighten the screws in the front of the drawer once it is in the  
right position.  
3
Unscrew the attachment brackets  
from the freezer drawers.  
These attachment brackets will be mounted onto the freezer  
panels.  
Side view of the freezer drawer  
pulled out  
Important!  
Thescrewsareneededforre-mountingthepre-assembled  
freezer panels onto the freezer drawers.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting the attachment brackets onto the door panels  
Mark lines on the refrigerator door panels as shown in Fig. A.  
Align the dismounted brackets of the refrigerator doors to the lines on the refrigerator door panels as shown in Fig. A 1. Fasten each  
bracket with any hole wherever possible using a minimum of 6 screws 4 x 16 mm.  
Fasten the brackets provided onto the freezer drawer panels using three screws (4 x 16 mm) for each bracket (Fig. A2)  
.
Refrigerator door panels  
Fig. A 1  
Freezer drawer panel  
Freezer drawer panel  
Fig. A 2  
Fig. A  
Fig. A 2  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting the refrigerator panel  
The description is for one panel only. The procedure is the same  
for both panels.  
To make it possible to fasten the refrigerator panel at the bottom  
the soft-stop cylinder must be dismantled.  
6. Grasp the soft-stop cylinder and pull down (Fig. D).  
The soft-stop cylinder retracts in the detached state.  
1. Open the refrigerator door and suspend the refrigerator panel  
on the top adjusting pins (fig. B).  
2. Screwsecuringnutsontotheadjustingpinsandslightlytighten  
(fig. B).  
fig. D  
fig. B  
7. Transfer the lower edge of the attachment bracket onto the  
panel using a pencil. (fig. E). Remove the panel from the  
refrigerator door.  
3. Close the refrigerator door and check the height of the panel.  
4. Adjust the height of the panel if necessary. Undo the securing  
nuts and use the adjusting pins to adjust (fig. C).  
fig. E  
fig. C  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Dismantle the lower attachment bracket from the refrigerator  
door. Align the bracket to the lines on the refrigerator door  
panel. (fig. G).  
12. Fasten the refrigerator panel using the same screws that  
held the lower bracket before removal (fig. K).  
Fasten the bracket with any hole wherever possible using a  
minimum of 6 screws 4 x 16 mm.  
fig. K  
fig. G  
13. Extend the soft-stop cylinder and connect with the ball stud  
(fig. L).  
8. Opentherefrigeratordoorandsuspendtherefrigeratorpanel  
on the top adjusting pins (fig. H).  
9. Screw securing nuts onto the adjusting pins and slightly  
tighten (fig. H).  
fig. L  
14. Click cover into place (fig. M).  
fig. H  
10. Move the panel to the left until it makes contact with the  
center rail (fig. I).  
11. Tighten the hex nuts finally.  
fig. M  
fig. I  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting the dust filter  
Mounting the freezer panels  
The supplied dust filter prevents that dir t enters the motor compar t-  
ment, reducing the refrigeration performance. Therefore always  
install the dust filter.  
1. Pulloutthetopfreezerdrawerandscrewonthepre-assembled  
panel. The same screws must be used as those used to screw  
on the attachment brackets (3.5 x 13).  
1. Pull the bottom freezer drawer right out.  
2. Remove the protective film from the dust filter. Insert the filter  
at the bottom, press the button down and click the filter into  
place.  
2. Close the freezer drawer and check the position of the panel.  
Adjust the height of the panel by undoing the left and right  
screws. Tighten the screws.  
3. Pull out the bottom freezer drawer and mount the panel in the  
same way.  
4. For both drawers, cover the gap between the drawer and the  
panel with the cover strips supplied. Remove the protective  
film from the trim and insert into the gap at the top.  
Mounting the ventilation grille  
Important!  
To ensure fault-free operation of the appliance, you must  
install the supplied ventilation grille.  
Do not obstruct the ventilation opening or cover it with a  
panel!  
3.5 x 13 mm  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

KTM Motorcycle 200 SX User Manual
Lasko Fan 758000 User Manual
LG Electronics Washer WD 102415WFH User Manual
Life Fitness Home Gym 07DT XXXXX XX User Manual
LOREX Technology DVR L174P 81 User Manual
Magnavox CRT Television MTV 34 MTV 51 MTV 68 User Manual
Maytag Washer MGR8670W User Manual
Melissa Electric Shaver 638 131 User Manual
Microsoft Video Game Controller 032502 User Manual
Micro Star Computer Computer Hardware G52 73601X1 User Manual