LevelOne Switch KVM 0221 KVM 0421 User Manual

LevelOne  
KVM-0221/KVM-0421  
KVM-0222/KVM-0422  
2/4-Port USB KVM Switch  
User Manual  
Ver. 1.0.0-0711  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
LevelOne KVM-0221/KVM-0421/KVM-0222/KVM-0422 is 2/4-port Slim Desktop USB KVM  
Switch with optional audio and microphone switching function in select models. The KVM  
switch allows users to access, control two (KVM-0221/0222) or four (KVM-0421/0422)  
USB-enabled computers from a single console. (Keyboard, Monitor, Mouse, and speaker  
set and microphone). It also offers user-programmable simultaneous/independent  
switching of PC channel and Audio/Mic channel for flexible multimedia application with  
KVM switching. For users who might need to use a hotkey preceding sequence other than  
scroll locks, LevelOne KVM switch also offers five alternatives keys for easy configuration.  
Setup is fast and easy; plugging cables into the appropriate ports is all that is entailed.  
LevelOne KVM Switch provides two convenient methods to bring the KVM focus to the  
target computer:  
a) By pressing one of the port selection switches located on the unit’s front panel.  
b) By entering the hotkey combinations from the keyboard.  
There is no better way to access your multiple computers than with LevelOne KVM switch.  
By allowing a single console to manage all of the computers, the KVM switch eliminates the  
expense of purchasing a separate keyboard, monitor and mouse for each one. Additionally,  
it saves the extra space and energy costs that additional consoles would require, and it  
eliminates the inconvenience and waste effort involved in constantly having to move around  
from one computer to another.  
Note  
KVM-0222 and KVM-0422 are non-audio models without Audio and  
Microphone support.  
1.1 Feature overview  
1
2
3
4
5
6
7
2-port Slim Desktop USB KVM switch  
Share Speakers and Microphone between computers (KVM-0221/KVM-0421)  
Hot-plugging PCs for maintenance without powering down the KVM Switch or PCs  
Computer selection via hotkeys or push buttons  
Auto-scan mode for PC monitoring  
LED display for easy status monitoring  
High VGA resolution supports up to 2048 x 1536  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
1.2 Package Contents  
z
z
z
z
KVM-0221/KVM-0421/KVM-0222/KVM-0422  
KVM Cable Set  
CD Manual  
Quick Installation Guide  
Check to make sure that all of the components are present and in good condition.  
If anything is missing, or was damaged in shipping, please contact your dealer immediately.  
Read this manual thoroughly and follow the installation and operation procedures carefully  
to prevent any damage to the KVM switch or to any other devices on the installation.  
Note  
2-Port USB KVM Switch KVM-0221 and KVM-0222 contains with 2 cable sets  
in the package.  
4-Port USB KVM Switch KVM-0421 and KVM-0422 contains with 4 cable sets  
in the package.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2. Hardware Installation  
The default setting of the KVM-0221/KVM-0421/KVM-0222/KVM-0422 is appropriate for  
most systems. The KVM Switch is a Plug-and-Play device for installation. In fact, user does  
not need to configure the KVM Switch before installation.  
For the first time installation of the KVM Switch, please follow the instructions below for  
setup sequence:  
1. Connect the shared keyboard, monitor and mouse (and optional speaker set and  
microphone) to the KVM Switch first, and then connect the computers.  
2. Power up your connected computers  
Since the KVM Switch receives power from the computer’s USB interface, it is powered up  
when user connects the KVM Switch to a PC.  
Please see next section for detail installation.  
2.1 Step by Step Installation  
Take the companion CD, KVM Cables and the KVM Switch out of the box and follow the  
steps below for installation.  
1. Insert the companion CD into CD-ROM drive, the Autorun screen will pop up  
automatically. (Please locate Autorun.exe in the CD and double-click it to start if the  
Autorun screen did not pop up).  
2. For Windows/Mac: Select “USB KVM” and then click on “Utility for Windows” or “Utility  
for Mac” to begin software installation. (If the Mac version software does not start, user  
should then copy the files to the local Hard disk on Mac). Follow the on screen  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
instructions to completion. When installation is complete, a LevelOne icon will be on the  
system tray of user’s desktop. For operation details of the KVM Switch utility, please  
refer to the user manual for detail.  
3. The Windows KVM Switch utility is recommended for use on Windows XP or later. The  
Mac KVM Switch utility is recommended for use on Mac OS 10.4 or later.  
Windows  
Mac OS  
No live connection detected  
Current active PC channel is on port 1  
Current active PC channel is on port 2  
The KVM Switch Utility supports both the Windows and the Mac OS operating systems. For  
other OS platforms such as Linux, user can only use the keyboard hotkey – Scroll Lock +  
Scroll Lock - to switch PC. However, this switching hotkey is not available on non-PC  
platform such as Mac OS.  
4. Connect the shared USB keyboard, USB mouse, D-Sub monitor, speaker/headphone  
and microphone each to its port on the KVM Switch.  
(Models KVM-0222 and KVM-0422 not support audio switching)  
5. Connect each KVM PC port to a computer, using the slim 3-in-1 KVM combo cable and  
the audio/MIC cable. Once the KVM Switch and computers connected properly, user  
can now operate the KVM Switch immediately.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note  
Some older computers with USB interface might need to manually enable the  
USB option in the BIOS setting before using USB devices. If USB interface  
does not work, please check the USB option setting in BIOS.  
2.2 Easy Operation  
There are three methods to control your KVM Switch for PC and Audio/MIC channel  
selection: using the Face-Panel Push Buttons, Hotkey Commands, or the KVM Switch  
Utility.  
Face-Panel Buttons  
The Face-Panel Buttons allow a direct control over PC port switching; simply press the  
button to switch PC port. By default, PC port switching and Audio/MIC switching are bound  
together (both will be switched simultaneously).  
Please notice that user is able to use the face-panel button to switch to an empty port that is  
not connected with any computer. Normally, if user uses keyboard hotkeys or the KVM  
Switcher software, it will not be able to switch to an empty port.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Keyboard hotkey  
There are two kinds of hotkey, User-definable hotkeys and Universal hotkey.  
For user-definable hotkey, user must install the software utility before using it.  
For universal hotkey, software utility installation is not necessary; user is able to use  
universal hotkey for PC switching even without software utility installed in the PC.  
User-definable hotkeys for PC selection:  
Hotkey sequence = Ctrl + Alt + [command key]*  
* Please refer to next section for keys that are qualified to be used as a command key  
Note  
The above hotkey sequence keys should be pressed and held together. And  
it is upon the release of all three keys, and then the switching action will be  
executed.  
Universal hotkey for PC toggle-switching:  
Universal Hotkey sequence = Scroll Lock + Scroll Lock  
* For other operating systems on PC such as Linux, user must use Universal Hotkey to  
facilitate PC switching. The universal hotkey is not available for Mac. HOWEVER, user can  
press button to switch in any case.  
The universal hotkey, Scroll Lock + Scroll Lock and the user-definable hotkey, Ctrl + Alt +  
[command key] WILL NOT allow user to switch to an empty port that is not connected with  
any computer. To force KVM to switch to an empty port, just press the face-panel button to  
switch.  
Each keystroke within a hotkey sequence should be pressed within 2 seconds. Otherwise,  
the hotkey sequence will not be validated.  
After perform port switching, user must wait till the KVM Switch icon shows forth the target  
port before user can perform next switching again. The KVM Switch icon could be found on  
the system tray of the Windows desktop after its installation.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
All the hotkeys are only functional after PCs are booting into the OS. If user would like to  
switch PC in the BIOS or pre-boot stage, press the face-panel button to switch.  
Each keystroke within a hotkey sequence should be pressed within 2 seconds.  
Otherwise, the hotkey sequence will not be validated.  
Scroll  
Lock  
Scroll  
Lock  
Please enter the  
Hotkey sequence in 2  
seconds  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. KVM Switch Utility Operation  
In addition to PC switching, the KVM Switch Utility also provides user more advanced  
functions such as described in below.  
Switch to PC x by Operation Menu  
Double click the KVM Switch utility icon on the desktop screen to evoke the operation menu,  
and then select whichever PC that is available for switching. Once user selects a PC  
channel, it will immediately switch to that PC. Note that the unconnected port(s) or the  
active port will be grayed-out and non-selectable.  
Windows:  
Operation Menu  
Configuration Dialog Box  
Mac OS:  
Operation Menu  
Configuration Dialog Box  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Switch to PC x by Keyboard Hotkeys  
Hit the hotkey according to your current hotkey definition:  
Hotkey sequence = Ctrl + Alt + [command key]*  
* The factory default hotkey setting is Ctrl + Alt + 1/2/3/4 for PC 1/2/3/4. User can also use  
Scroll Lock + Scroll Lock to switch PC.  
Start Auto-scan  
Double click the KVM Switch utility icon on the desktop screen to evoke the operation menu,  
and then select Start Auto-Scan to activate auto-scanning.  
Stop Auto-scan  
While auto-scanning, right-click the KVM Switch utility icon to evoke the operation menu,  
then select Stop Auto-Scan to de-activate auto-scanning. Or you can press any button on  
the face-panel to stop Auto-scan.  
KVM Switch Utility configuration  
Right-click the KVM Switch utility icon and select Settings or double-click the icon to bring  
up the configuration dialog box.  
Define Hotkey commands  
User can specify the command key as you like by typing it in. For example, you can specify  
the hotkey for switching to PC 1 as CTRL + ALT + A by typing an A (not case-sensitive) in  
the editable field.  
Hotkey Sequence = CTRL + ALT + [command key]*  
* The command key is user-definable via the configuration dialog box  
Except those control keys such as Alt, Ctrl, Shift, CAPS, Tab, Esc and those functions keys  
and edit keys, all other keys on the keyboard, including those number keys on the number  
pad are all qualified to be used as hotkey command key. In addition to the software KVM  
Switching by the operation menu and the user-defined hotkeys, user can always use the  
universal hotkey for PC switching – Scroll Lock + Scroll Lock  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fix Audio Port at PC x  
Check this option and then select the PC to fix the audio/mic channel to the selected PC.  
Once this option is checked, the audio/mic channel will be fixed and become  
non-switchable.  
Auto Scan Period  
Select the Auto-scan period from 10 ~ 60 seconds with an increment of 5 seconds. The  
Auto-scan period is the time KVM Switch will wait to switch to next PC.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Switch Mode on Various Operating System  
Operating System  
Windows  
USB KVM Switch  
- Face-panel button  
- Software Menu Switching  
- User-definable hotkeys (Software hotkeys)  
- Universal hotkey  
Linux  
Mac OS  
SUN  
- Universal hotkey  
- Face-panel button  
- Software Menu Switching  
- User-definable hotkeys (Software hotkeys)  
- Face-panel button  
- Switch utility only available for USB KVM Switch models  
- Software Hotkeys for USB model - Ctrl-Alt-(x)  
- USB model Software switch functional feature:  
Select right-click menu item for port switching;  
Check option items for operations such as –  
Note  
fix audio port at PC x  
Autoscan  
Universal hotkey selection  
Autoscan period  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Technical Specification  
Model No.  
KVM-0221/0222  
KVM-0421/0422  
PC Port  
2
4
PC Port Connector  
(All Female Types)  
VGA HDDB 15pin-F (integrated with USB interface)  
1 x USB Type A  
1 x HDB 15-pin female  
Local Console Port  
(All Female Types)  
1 x 3.5 mm audio/mic jack (KVM-0221/0421)  
PC selection  
HotKeys, Push Button, Software Utility  
PC Port LED  
2 (Green)  
4 (Green)  
Keyboard Emulation  
Mouse Emulation  
VGA Resolution  
Housing  
USB  
USB  
2048 x 1536  
Plastic  
KVM Switch Power Type  
Operation Temperature  
Storage Temperature  
Humidity  
USB Interface Power  
0~40  
-10 ~ 50℃  
0~80% RH Non-Condensing  
100(L) X 71.5(W) X 26 (H) 170(L) X 87(W) X 26 (H)  
Dimension (mm)  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

Lenmar Enterprises Pacemaker nvh600 User Manual
Leviton Video Gaming Accessories MRS4 User Manual
LG Electronics Computer Monitor 47VL10 User Manual
LG Electronics DVD Player DR1F9M User Manual
LG Electronics Range LDE3031ST User Manual
Lightolier Indoor Furnishings 1101FDL User Manual
Logitech Computer Keyboard 920 002836 User Manual
Makita Sander BO5021 User Manual
Maxim Computer Hardware DS5001FP User Manual
Metabo Power Hammer 600396420 User Manual