®
COMPACT DISC PLAYER
AM/FM STEREO CASSETTE RECORDER
MODEL CD-106
OPERATING INSTRUCTIONS
PLAYS ALL MUSIC COMPACT DISCS
FULLY PROGRAMMABLE CD PLAYER WITH REPEAT
RECEIVES AM/FM STEREO BROADCASTS
RECORDS FROM CD, RADIO, OR BUILT-IN MICROPHONE
FM STEREO AND POWER LED INDICATORS
2 WAY POWER - AC/DC
BASS BOAST SYSTEM
REQUIRES 8 SIZE “C” BATTERIES
•
•
•
•
•
•
•
•
PLEASE READ CAREFULLY BEFORE USE
CD-106081199 AS v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
14. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids
are not spilled into the enclosure through openings.
15. Damage Requiring Service - The appliance should be serviced by qualified service
personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked change in
performance; or
E. The appliance has been dropped, or the enclosure damaged.
16. Servicing - The user should not attempt to service the appliance beyond that described
in the operating instructions. All other servicing should be referred to qualified service
personnel.
17. Power lines - An outdoor antenna should be located away from power lines.
18. Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be
sure the antenna system is grounded so as to provide some protection against voltage
surges and built up static charges. Section 810 of the National Electrical Code, ANSI/
NFPA 70 provides information with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See Figure.
EXAMPLE OF ANTENNA GROUNDING AS PER
NEC - NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT (NEC
SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
It is the intent of Lenoxx that this product be used in full compliance with the copyright
laws of the United States and that prior permission be obtained from copyright owners
whenever copying tapes or CD’s.
Do not apply oil or petroleum products or solvents to any part of this set.
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This compact disc player is classified as CLASS 1 LASER PRODUCT as stated on
the back of the set.
2
CD-106081199 AS v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY OR DAMAGE TO YOUR
SET, READ AND FOLLOW THESE INSTRUCTIONS.
1. Use only the type and size of batteries mentioned in the operating instructions
booklet (batteries are not included with this set, please buy the proper batteries).
2. Do not dispose the batteries into a fire. The cells may explode. Check with local
codes for possible special disposal instructions.
3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
4. Be careful when handling batteries in order not to short the battery with conducting
materials such as rings, bracelets and keys. The battery or conductor may over
heat and cause burns.
5. Do not attempt to recharge non-rechargeable batteries. The batteries may leak
corrosive electrolyte or explode.
6. Do not attempt to rejuvenate the batteries identified for use with this product by
heating them. Sudden release of the battery electrolyte may cause burns or
irritation to eyes or skin.
7. All batteries should be replaced at the same time. Mixing fresh and discharged
batteries could increase internal cell pressure and rupture the batteries.
8. When inserting batteries into this product, the proper polarity (
and
) or
direction must be observed. Reverse insertion of some or all of the batteries may
result in battery eletrolyte leakage or explosion.
9. Remove the batteries from this product if the product will not be used for a long
period of time (several months or more) since during the period the batteries could
leak, damaging the product.
10. Discard weak or dead batteries as soon as possible since they are more likely to
leak in the product. Batteries should be replaced (depending on the product) when
the display gets dim or if the Low Battery Indicator shows or if the sound gets
distorted.
11. Do not store this product in high temperature areas. Batteries that are stored in a
freezer or refrigerator for the purpose of extending shelf life should be protected
from condensation during storage and defrosting. Batteries should be stabilized at
room temperature prior to use after cold storage.
12. If this product does not operate normally, see TROUBLE SHOOTING on page 18. If
you can’t resolve the problem, or if the product is damaged, refer to the LENOXX
WARRANTY INFORMATION. Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause electric shock
when the appliance is subsequently used.
13. If liquid leaks from the batteries, carefully wipe this liquid. Do not allow it to touch
your skin, and discard the leaking batteries.
14. Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.).
15. The use of rechargeable batteries is not recommended for this set because their
voltage and life is lower than standard batteries.
16. Installation of batteries should be done by an adult only.
SAVE THESE INSTRUCTIONS
3
CD-106081199 AS v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing a CD
3
2
4
1
Connect the supplied AC power cord or batteries(see page 14).
FUN C TIO N
C D
Slide the Function Switch to
CD position (power on).
1
2
RAD IO
TAPE
Press the CD Door Open
button to open the CD Door
and place the CD in the CD
compartment.
OPEN
The label side of the CD
should face upward.
Close the CD Door by
pushing it down at the
position marked CLOSE.
3
4
CLOSE
Press the CD Play/Pause
Button. The player plays all
the tracks once.
PLAY/PAUS E
Play/Pause
Lamp
Track
number
4
CD-106081199 AS v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Use these buttons for additional operations
Open
Volume Control
Button
Function
Switch
Play/Pause Lamp
Tip
When CD play is
paused, the Play/
Pause Lamp will
flash and no music
will play.
To
Press or Adjust
Adjust the volume
Stop playback
Volume Control
To resume play,
press the Play/
Pause Button again,
Pause playback
The Play/Pause Lamp will
flash during pause. Press
again to resume play.
the
Play/Pause
Lamp will stop
flashing and music
will play.
Go to the next track
Go back to the previous
track
or
while playing,
Locate a point in a song
press and hold down until
you find the point.
CD Door Open Button
Remove the CD
(press
first)
Slide the Function Switch
to TAPE position
Turn off the power
CD-106081199 AS v.1 E
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing CD tracks repeatedly (Repeat Play)
Repeat
Lamp
Program
Lamp
Play/Pause
Lamp
Function
Switch
Repeat
Program
1. Slide the Function Switch to CD position.
2. Press the CD Repeat Button.
To repeat
Press
Repeat Lamp
a single track (song)
Press the Repeat Button once
Press the Repeat Button twice
Flashing
all the tracks (all songs)
Steady on
Steady on
(the Program
Lamp flashing)
programmed songs (see
program instructions on
next page)
Press the Program Button, and
then the Repeat Button twice
3. Press
.
4. You may select the track by pressing
or
.
To cancel Repeat Play
Press the Repeat Button until the Repeat Lamp is off.
CD-106081199 AS v.1 E
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating your own music program
(Program Play)
Program
Lamp
Repeat
Lamp
You can make a program of up
to 19 tracks in the order you
want them to be played.
Program
Button
Play/Pause
Lamp
1. Slide the Function Switch to CD position. Make sure
the CD is stopped.
2. Press the Program Button. The number “0” and the
Program Lamp will flash.
P R O G .
3. Press
or
to select the tracks you want to
program in the order you want.
4. Press the Program Button to confirm. The number “0”
and the Program Lamp will flash.
P RO G .
5. Repeat steps 3 and 4. You can program up to 19
tracks.
6. Press
to start program play. The Play/Pause Lamp
turns on and the Program Lamp will remain flashing.
To change the current program
Just creat a new program by following the above programming procedures.
To cancel Program Play
Press the Stop Button and the Program Lamp goes off.
7
CD-106081199 AS v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the radio
1
2
3
4
Connect the supplied AC power cord or batteries (see page 14).
FUN C TIO N
Slide the Function Switch to
RADIO position (power on).
1
2
C D
RAD IO
TAPE
Slide the Band Switch to the proper
band position that you want.
BAN D
FM
AM
3
4
Tune into the station you prefer
using the Tuning Control. Adjust
for the clearest sound.
This indicator will light up when
receiving FM Stereo broadcasts.
FM ST.
CD-106081199 AS v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Use these buttons for additional operations
Volume
Control
Function
Switch
Tip
To
Slide or Adjust
When the player is
•
Adjust the volume
Volume Control
receiving from a FM
stereo broadcast, the
FM Stereo indicator will
be on.
Slide the Function Switch
to TAPE position
Turn off the Radio
To improve broadcast reception
Reorient the antenna for FM or FM Stereo. Reorient
the player itself for AM.
FM STEREO
INDICATOR
9
CD-106081199 AS v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing a tape
1
3 2
Connect the supplied AC power cord or batteries (see page 14).
Slide the Function
FUN C TIO N
C D
1
Switch
to
TAPE
position.
RAD IO
TAPE
Press the Stop/Eject
Button to open the tape
2
FU L L
RE E L
E M P T Y
RE E L
compartment
and
insert a recorded tape.
Close the door.
STOP/EJECT
Press the Play Button.
The player turns on
and starts playing.
3
PLAY
10
CD-106081199 AS v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Use these buttons for additional operations
Volume
Control
Bass Boost
Switch
Pause
Play Fast F.&
Rewind
Stop/Eject
Tip
To
Press or Adjust
Volume Control
When the tape finishes
Adjust the volume
Stop playback
playing that side of the
tape, the set will stop. To
hear the otherside, flip
tape over, then insert and
press Play.
Stop/Eject Button
Fast forward or rewind the
tape
Fast Forward Button or
Rewind Button
Pause playback
Pause Button
Press again to resume
play after pause.
Eject the cassette
Stop/Eject Button
Bass Boost Switch
Get different sound effect
To enjoy the music without
disturbing others
Insert your headphone
plug into the Headphone
Jack
11
CD-106081199 AS v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on a tape
2
3
1
Connect the supplied AC power cord or batteries (see page 14).
Press the Stop/Eject
Button to open the tape
compartment and insert
a blank tape. Select the
program source (AM,
FM, CD, or, built-in
microphone) you want
to record.
1
2
STOP/EJECT
To record from the CD player,
insert a CD and follow the steps to
play a CD (see page 4).
FUN C TIO N
C D
RAD IO
TAPE
To record from radio, slide the
Function Switch to RADIO
position, and tune into the station
you want (see page 8).
To record from the built-in
microphone, leave the Function
Switch at TAPE position, and
speak in front of the set.
Press the Record Button to start
recording. (The Play Button is
depressed automatically.)
3
RECORD
CD-106081199 AS v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Use these buttons for additional operations
FUNCTION
SWITCH
Tip
• Adjusting the Volume
or Bass Boost Switch
will not affect the
recording level.
PAUSE
STOP/EJECT
• For best recording
effect, use the AC
power instead of
batteries.
To
Press or Adjust
Stop recording
Stop/Eject Button
Pause recording
Pause Button
Press the button again to
resume recording.
• To erase a recording,
just start a new one,
and the old recording
is automatically
Turn off the power
Press the Stop/Eject
Button and slide the
Function Switch to TAPE
position.
replaced.
CD-106081199 AS v.1 E
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Choosing the power sources
You can use the AC power or batteries as a power source.
AC SOCKET
1. To a wall outlet
2. Battery compartment
Tip
1. Connecting the AC power
cord
Insert one end of the supplied AC power cord to
the socket located at the rear of the set, and the
other end to the wall outlet.
The plug of the AC power
cord is polarized and only fits
one way into the wall outlet
and back of the set.
If this plug does not match
your outlet, do not force it.
Reverse it and try again.
2. Operate the set on batteries
Insert 8 size “C” batteries (not included) into the
battery compartment.
Tip
Replace the batteries when
the Power/Batt. Lamp gets
dim or when the player stops
operating. Replace all the
batteries with fresh ones.
Before you replace the
batteries, be sure to remove
the CD from the player and
remember to check the
Battery Safety Instructions
on Page 3.
To operate the set on batteries, disconnect the
AC power cord from the player.
c
c
c
c
UPPER
LO WER
c
c
c
c
14
CD-106081199 AS v.1 E
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
On safety
On power sources
As the laser beam used in the CD
For battery operation, use 8 size “C”
•
•
player section is harmful to the eyes,
do not attempt to disassemble the
casing. Refer servicing to qualified
personnel only.
batteries. We recommend alkaline
batteries for longer life.
When the batteries are not to be used,
•
remove them to avoid damage that can
be caused by battery leakage or
corrosion.
Should any solid object or liquid fall
•
into the set, disconnect the power, and
have it checked by qualified personnel
before operating it any further.
The nameplate indicating operating
voltage, power consumption, etc. is
located at the back of the set.
•
On placement
On operation
Do not leave the set in a location
If the set is brought directly from a
•
•
near heat source, or in a place subject
to direct sunlight, excessive dust or
mechanical shock.
cold to a warm location, or is placed in
a
very damp room, moisture may
condense on the lens inside the CD
set section. Should this occur, the
set will not operate properly. In this
case, remove the CD and wait about
an hour for the moisture to evaporate.
If the set has not been used for a
long time, set it in the playback mode
to warm it up for a few minutes before
inserting a cassette.
Do not place the set on an inclined
or unstable place.
•
Do not place anything within 1 inch of
•
the back of the cabinet. The ventilation
holes must be unobstructed for the
set to operate properly and prolong
the life of its components.
If the set is left in a car parked in
•
This CD player is designed to be played
on a stable no vibration position. If you
bump the set during CD play, the music
will stop or skip for a few seconds. This
is normal for this type of player.
If you have any questions or problems
concerning your player, please contact
our customer service department at
1-800-315-5885 (MONDAY - FRIDAY
09:00 - 17:00 EST).
the sun, be sure to choose a location
in the car where the set will not be
subjected to the direct rays of the sun.
•
•
Since a strong magnet is used for the
•
speakers, keep personal credit cards
using magnetic coding or spring-
wound watches away from the set
to prevent possible damage from the
magnet.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-106081199 AS v.1 E
Precautions (continued)
Notes on CDs
Notes on cassettes
Before playing, clean the CD with a
cleaning cloth. Wipe the CD from the
center out.
Break off the cassette tab from side A
•
•
or B to prevent accidental recording. If
you want to reuse the tape for
recording, cover the broken tab with
adhesive tape.
Side A
Tab for side A
Tab for side B
Do not use solvents such as benzene,
•
thinner, commercially available
cleaners or anti-static spray intended
for vinyl LPs.
To record on a tape with its tab broken
off, cover the respective tab hole for
side A or B with adhesive tape.
•
Do not expose the CD to direct
•
sunlight or heat sources such as hot
air ducts, nor leave it in a car parked
in direct sunlight as there can be a
considerable rise in temperature inside
the car.
The use of a cassette with more than
•
90 minutes of play time is not
recommended except for long
continuous recording or playback.
To reduce the chances of tape jamming
Do not stick paper or sticker on the
CD, nor scratch the surface of the CD.
After playing, store the CD in its case.
•
•
or tangling, you should check that
there are no loose layers of tape visible
through the cassette center window
if any, tighten these loose layers of
tape using a pencil before inserting the
cassette into the set.
•
If there is a scratch, dirt or fingerprints
on the CD, it may cause tracking error.
CD-106081199 AS v.1 E
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning the lens
Notes for storing cassette
tapes
If the lens becomes dirty, it may cause a
skipping of sound during CD operation.
Clean with a commercially available lens
cleaner blower.
1. Do not put a tape near a magnetic field,
such as a TV, or speaker. Magnetic
fields may reduce the tape sensitivity
or even erase the recording.
2. Do not store tape for any length of time
in a hot, moist or dusty place.
Cleaning the tape heads
and tape path
Cleaning the cabinet
Wipe the heads, the pinch roller and the
capstan with a cleaning swab slightly
moistened with cleaning fluid or alcohol
after every 10 hours of operation for
optimum playback and recording quality.
Clean the cabinet, panel and controls with
a soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder, or solvent,
such as alcohol or benzene.
RECORD / PLAY BACK HEAD
PINCH ROLLER
ERASE HEAD
CAPSTAN
COTTON SWAB
After cleaning, insert a tape when the
areas cleaned are completely dry.
CD-106081199 AS v.1 E
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Remedy
Problem
Connect the AC power cord to a wall
outlet securely.
•
The power is not on.
Make sure the batteries are inserted
correctly and they are fresh.
•
Make sure the Function Switch is at the
right position as you want.
•
There is no sound.
Adjust the volume.
Unplug the headphones when listening
through speakers.
•
•
“
” appears in the display
Make sure the CD with the label side up.
•
even when a CD is in place.
Make sure that the CD compartment is
closed.
•
CD does not play.
Place the CD with the label side up.
•
CD play is paused, press
again.
•
•
Remove the CD and leave the CD door
open for about an hour to dry moisture
condensation.
Make sure the Function Switch is at CD
position.
•
Clean the CD, or replace it if the CD is
badly damaged.
Place the set in a location free from
•
•
The sound drops out.
vibration.
Check if all batteries are fresh.
•
•
Replace all the batteries with fresh ones if
they are weak, or bring the set near a
window, or rotate the set (for AM) or adjust
the FM antenna for best FM reception.
The sound is weak or of poor
quality.
Make sure the safety tab on the cassette
is in place.
Make sure the Function Switch is at TAPE
position.
The Record Button does not
function / The tape does not
play.
•
•
Clean the erasing head (see page 17).
Replace all the batteries with fresh ones if
they are weak.
•
•
The tape does not erase
completely.
Make sure the tape is inserted properly.
Make sure the cassette tab is in place.
The tape does not record.
•
•
•
Clean the heads, pinch roller and capstan
(see page 17).
The sound is weak / The sound
quality is poor.
The tape has reached its end. Remove it,
flip to the other side, re-insert and press
Play.
•
Cassette Play Button pops up.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-106081199 AS v.1 E
Specification
GENERAL DESCRIPTION
Power source:
AC 120V, 60Hz 12Watts
DC 12V (8 size “C” batteries)
(we recommend alkaline batteries for longer life)
Speakers:
3” 8 ohm x 2
Output power:
Dimensions:
2W / channel
1
Width: 12 / ”
4
5
Depth: 10 / ”
8
8
1
Height: 7 / ”
Weight: 7LBs (without batteries)
CD SECTION
Plays disc type:
Any normal CD used in portable players
760 - 800 nm
Laser wavelength:
Tracking method:
3 - spot error detection
3.86 mm lens
Frequency response: 80 Hz - 15 KHz
TAPE RECORDER SECTION
Tape:
Standard normal bias cassette tape
Frequency response: 150 - 8000 Hz
RADIO SECTION
Frequency range:
FM: 88 - 108 MHz
AM: 530 - 1700 KHz
LENOXX reserves the right to make design and specification changes for product
improvement.
PROTECT YOUR FINE FURNITURE!
WE RECOMMEND A CLOTH OR OTHER PROTECTIVE MATERIAL BE PLACED UNDER
THE SET WHEN PLACING IT ON SURFACE WITH A NATURAL OR LACQUER FINISH.
© 1999 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-106081199 AS v.1 E
|