Lenovo Server TS130 User Manual
ThinkServer TS130  
Hardware Maintenance Manual  
Machine Types: 1098, 1100, 1105, and 1106  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Chapter 1. About this manual . . . . . 1  
Inspecting for unsafe conditions .  
Guidelines for servicing electrical equipment .  
.
.
.
.
.
31  
32  
33  
34  
Important Safety Information .  
Safety information .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
2
.
.
.
.
Removing the server cover .  
.
.
.
.
.
.
.
.
.
.
.
.
Important information about replacing RoHS  
compliant FRUs .  
Removing and reinstalling the front bezel .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
7
Installing, removing, or replacing optional hardware  
devices  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
35  
35  
38  
39  
41  
43  
Chapter 2. General information. . . . . 9  
Installing or replacing a PCI card .  
Installing or removing the Ethernet card .  
Installing or removing a memory module.  
Installing or replacing the optical drive  
Replacing the primary hard disk drive .  
Features and specifications.  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
9
11  
11  
11  
Software programs .  
EasyStartup .  
.
.
.
.
.
.
.
.
.
Reliability, availability, and serviceability .  
Installing or replacing the secondary hard disk  
Chapter 3. Diagnostics and  
drive .  
Installing, removing, or replacing hardware  
devices  
Replacing the power supply assembly  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
46  
PC-Doctor for DOS .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
49  
50  
52  
Creating a diagnostic disc  
Running the diagnostic program from a  
diagnostic disc.  
Replacing the heat sink and fan assembly .  
Replacing the front audio and USB  
.
.
.
.
.
.
.
Navigating through the diagnostic program  
assembly .  
Replacing the front fan assembly  
Replacing the rear fan assembly .  
Replacing the microprocessor .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
54  
55  
57  
59  
62  
63  
66  
67  
67  
67  
68  
68  
Running tests .  
Viewing the test log .  
Basic troubleshooting .  
General problems.  
Troubleshooting tables  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Replacing the system board battery  
Replacing the system board  
Completing the parts replacement .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Hard disk drive boot error  
Power supply problems  
Beep symptoms .  
POST error codes.  
EasyStartup problems .  
Miscellaneous error messages  
Undetermined problems .  
.
Connecting the cables .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Turning on the server  
Turning off the server  
.
.
Connecting external devices  
Updating the server configuration  
.
.
Chapter 6. Parts listing . . . . . . . . 69  
Chapter 4. Locating parts, controls,  
LEDs, and connectors . . . . . . . . 23  
Replaceable server components.  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
69  
75  
76  
Ship group .  
Power cords  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Front view  
Front control panel LEDs.  
Rear view. .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
23  
23  
24  
26  
27  
Chapter 7. Configuring the server . . 83  
.
.
.
.
.
Using the Setup Utility program .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
83  
83  
83  
96  
96  
98  
99  
99  
99  
99  
Locating parts on the system board  
Internal components  
Starting the Setup Utility program  
Introduction of the BIOS items.  
Viewing and changing settings  
.
.
.
.
.
.
.
.
.
.
.
Chapter 5. Replacing FRUs. . . . . . 29  
Guidelines  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
29  
29  
30  
30  
31  
31  
Using passwords .  
Enabling or disabling a device .  
Selecting a startup device  
.
.
.
.
.
Basic guidelines .  
System reliability guidelines.  
Handling static-sensitive devices  
Working inside the server with the power on .  
.
.
Exiting from the Setup Utility program.  
Configuring RAID.  
RAID level.  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Guidelines for trained service technicians .  
© Copyright Lenovo 2011  
.
.
.
.
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
Configuring the system BIOS to enable SATA  
Using other services  
Purchasing additional services  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
108  
108  
RAID functionality.  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
100  
100  
100  
101  
101  
Creating RAID volumes  
Deleting RAID volumes  
Appendix C. Notices . . . . . . . . 109  
Resetting disks to non-RAID  
Updating the firmware. .  
Trademarks .  
Important notes .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
110  
110  
110  
110  
111  
.
.
.
Using the EasyUpdate Firmware Updater  
program  
Using the ThinkServer EasyStartup program .  
Polyvinyl Chloride (PVC) cable and cord notice .  
Recycling information .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
101  
102  
102  
102  
103  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Battery return program.  
Updating system programs.  
.
.
.
.
.
.
.
.
.
.
.
.
.
Requirement for batteries containing  
Using system programs .  
perchlorate .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
112  
112  
Updating (flashing) the BIOS from a disc.  
Updating (flashing) the BIOS from your  
Particulate contamination  
Important information for the European Directive  
operating system .  
.
.
.
.
.
.
.
.
.
.
.
.
103  
104  
2002/96/EC .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
113  
Recovering from a POST and BIOS update  
failure  
Restriction of Hazardous Substances Directive  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
(RoHS) .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
116  
117  
117  
118  
118  
118  
China RoHS .  
Appendix A. Information  
resources . . . . . . . . . . . . . . 105  
Turkish statement of compliance .  
Ukraine RoHS . .  
German Ordinance for Work gloss statement.  
Electronic emission notices. .  
.
.
.
.
.
.
Safety and Warranty  
Lenovo Web site (http://www.lenovo.com) .  
Lenovo Support Web site .  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
105  
105  
105  
.
.
.
.
.
.
.
.
.
.
.
.
Federal Communications Commission (FCC)  
Statement.  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
118  
Appendix B. Help and service . . . 107  
Using the documentation  
Calling for service  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
107  
107  
Index. . . . . . . . . . . . . . . . . 121  
.
.
.
ii ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1. About this manual  
This Hardware Maintenance Manual contains information to help you solve problems that might occur in  
your server. It describes the diagnostic tools that come with the server, error codes and suggested actions,  
and instructions for replacing failing components.  
Replaceable components are of three types:  
• Self-service customer replaceable unit (CRU): Replacement of self-service CRUs is your responsibility.  
If Lenovo® installs a self-service CRU at your request, you will be charged for the installation.  
• Optional-service customer replaceable unit: You may install an optional-service CRU yourself or  
request Lenovo to install it, at no additional charge, under the type of warranty service that is designated  
for the server.  
• Field replaceable unit (FRU): FRUs must be installed only by trained service technicians.  
The most recent version of this document is available at http://www.lenovo.com/support.  
Before servicing a Lenovo product, be sure to read the Safety Information. See “Important Safety  
Information” on page 1.  
For information about the terms of the warranty and getting service and assistance, see the Warranty and  
Support Information document.  
Important Safety Information  
Be sure to read all caution and danger statements in this book before performing any of the instructions.  
Veuillez lire toutes les consignes de type DANGER et ATTENTION du présent document avant d'exécuter  
les instructions.  
Lesen Sie unbedingt alle Hinweise vom Typ “ACHTUNG” oder “VORSICHT” in dieser Dokumentation, bevor  
Sie irgendwelche Vorgänge durchführen.  
Leggere le istruzioni introdotte da ATTENZIONE e PERICOLO presenti nel manuale prima di eseguire una  
qualsiasi delle istruzioni.  
Certifique-se de ler todas as instruções de cuidado e perigo neste manual antes de executar qualquer  
uma das instruções.  
Es importante que lea todas las declaraciones de precaución y de peligro de este manual antes de seguir  
las instrucciones.  
© Copyright Lenovo 2011  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Safety information  
Important: Each caution and danger statement in this document is labeled with a number. This number  
is used to cross reference an English-language caution or danger statement with translated versions of  
the caution or danger statement in the Safety Information document. For example, if a danger statement  
is labeled “Statement 1,” translations for this danger statement are in the Safety Information document  
under “Statement 1.”  
Be sure to read and understand all caution and danger statements in this document before you perform the  
procedures. Read and understand any additional safety information that comes with the server or optional  
device before you install, remove, or replace the device.  
Statement 1  
DANGER  
Electrical current from power, telephone, and communication cables is hazardous.  
To avoid a shock hazard:  
• Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this  
product during an electrical storm.  
• Connect all power cords to a properly wired and grounded electrical outlet.  
• Connect to properly wired outlets any equipment that will be attached to this product.  
• When possible, use one hand only to connect or disconnect signal cables.  
• Never turn on any equipment when there is evidence of fire, water, or structural damage.  
• Disconnect the attached power cords, telecommunications systems, networks, and modems before you  
open the device covers, unless instructed otherwise in the installation and configuration procedures.  
• Connect and disconnect cables as described in the following table when installing, moving, or opening  
covers on this product or attached devices.  
To connect:  
To disconnect:  
1. Turn everything OFF.  
1. Turn everything OFF.  
2. First, attach all cables to devices.  
3. Attach signal cables to connectors.  
4. Attach power cords to outlet.  
5. Turn devices ON.  
2. First, remove power cords from outlet.  
3. Remove signal cables from connectors.  
4. Remove all cables from devices.  
2
ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Statement 2  
DANGER  
Danger of explosion if battery is incorrectly replaced.  
When replacing the lithium coin cell battery, use only the same or an equivalent type that is  
recommended by the manufacturer. The battery contains lithium and can explode if not properly  
used, handled, or disposed of.  
Do not:  
• Throw or immerse into water  
• Heat to more than 100°C (212°F)  
• Repair or disassemble  
Dispose of the battery as required by local ordinances or regulations.  
Statement 3  
CAUTION:  
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are  
installed, note the following:  
• Do not remove the covers. Removing the covers of the laser product could result in exposure to  
hazardous laser radiation. There are no serviceable parts inside the device.  
• Use of controls or adjustments or performance of procedures other than those specified herein  
might result in hazardous radiation exposure.  
DANGER  
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following.  
Laser radiation when open. Do not stare into the beam, do not view directly with optical  
instruments, and avoid direct exposure to the beam.  
Chapter 1. About this manual  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Statement 4  
≥ 18 kg (39.7 lb)  
< 32 kg (70.5 lb)  
≥ 32 kg (70.5 lb)  
< 55 kg (121.2 lb)  
≥ 55 kg (121.2 lb)  
< 100 kg (220.5 lb)  
CAUTION:  
Use safe practices when lifting.  
Statement 5  
CAUTION:  
The power control button on the device and the power switch on the power supply do not turn off  
the electrical current supplied to the device. The device also might have more than one power  
cord. To remove all electrical current from the device, ensure that all power cords are disconnected  
from the power source.  
Statement 6  
CAUTION:  
If you install a strain-relief bracket option over the end of the power cord that is connected to the  
device, you must connect the other end of the power cord to an easily accessible power source.  
Statement 7  
CAUTION:  
If the device has doors, be sure to remove or secure the doors before moving or lifting the device to  
avoid personal injury. The doors will not support the weight of the device.  
4
ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Statement 8  
CAUTION:  
Never remove the cover on a power supply or any part that has the following label attached.  
Hazardous voltage, current, and energy levels are present inside any component that has this label  
attached. There are no serviceable parts inside these components. If you suspect a problem with  
one of these parts, contact a service technician.  
Statement 9  
CAUTION:  
To avoid personal injury, disconnect the hot-swap fan cables before removing the fan from the device.  
Statement 10  
CAUTION:  
The following label indicates sharp edges, corners, or joints nearby.  
Statement 11  
CAUTION:  
The following label indicates a hot surface nearby.  
Statement 12  
DANGER  
Overloading a branch circuit is potentially a fire hazard and a shock hazard under certain conditions. To avoid  
these hazards, ensure that your system electrical requirements do not exceed branch circuit protection  
requirements. Refer to the information that is provided with your device for electrical specifications.  
Chapter 1. About this manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Statement 13  
CAUTION:  
Make sure that the rack is secured properly to avoid tipping when the server unit is extended.  
Statement 14  
CAUTION:  
Some accessory or option board outputs exceed Class 2 or limited power source limits and must be  
installed with appropriate interconnecting cabling in accordance with the national electric code.  
Statement 15  
CAUTION:  
The power-control button on the device does not turn off the electrical current supplied to the  
device. The device also might have more than one connection to dc power. To remove all electrical  
current from the device, ensure that all connections to dc power are disconnected at the dc power  
input terminals.  
Statement 16  
CAUTION:  
To reduce the risk of electric shock or energy hazards:  
• This equipment must be installed by trained service personnel in a restricted-access location, as  
defined by the NEC and the latest edition of IEC 60950, The Standard for Safety of Information  
Technology Equipment.  
• Connect the equipment to a reliably grounded safety extra low voltage (SELV) source. An SELV  
source is a secondary circuit that is designed so that normal and single fault conditions do not  
cause the voltages to exceed a safe level (60 V direct current).  
• The branch circuit overcurrent protection must be rated in accordance with local building codes.  
• Use 16 American Wire Gauge (AWG) or 1.3 mm2 copper conductor only, not exceeding 3 meters  
in length.  
• Torque the wiring-terminal screws to 12 inch-pounds (1.4 newton-meters).  
• Incorporate a readily available approved and rated disconnect device in the field wiring.  
Statement 17  
CAUTION:  
This product contains a Class 1M laser. Do not view directly with optical instruments.  
6
ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Statement 18  
CAUTION:  
Do not place any object on top of rack-mounted devices.  
Statement 19  
CAUTION:  
Hazardous moving parts. Keep fingers and other body parts away.  
Statement 20  
CAUTION:  
The battery is a lithium ion battery. To avoid possible explosion, do not burn the battery. Exchange it  
only with the Lenovo-approved part. Recycle or discard the battery as instructed by local regulations.  
Important information about replacing RoHS compliant FRUs  
RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive  
(2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS  
requirements must be implemented on Lenovo products placed on the market and sold in the  
European Union after June 2006. Products on the market before June 2006 are not required to  
have RoHS compliant parts. If the parts are not compliant originally, replacement parts can also  
be noncompliant, but in all cases, if the parts are compliant, the replacement parts must also be  
compliant.  
Note: RoHS and non-RoHS FRU part numbers with the same fit and function are identified with unique  
FRU part numbers.  
Lenovo plans to transition to RoHS compliance well before the implementation date and expects its suppliers  
to be ready to support Lenovo's requirements and schedule in the EU. Products sold in 2005 will contain  
some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo  
produces containing RoHS compliant parts.  
Chapter 1. About this manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
 
RoHS compliant ThinkServer® TS130 parts have unique FRU part numbers. Before or after June 2006, failed  
RoHS compliant parts must always be replaced using RoHS compliant FRUs, so only the FRUs identified as  
compliant in the system Hardware Maintenance Manual or direct substitutions for those FRUs can be used.  
Products marketed before June 2006  
Products marketed after June 2006  
Replacement FRU  
Replacement FRU  
Must be RoHS  
Current or original part  
Non-RoHS  
Current or original part  
Can be Non-RoHS  
Can be RoHS  
Must be RoHS  
Non-RoHS  
Non-RoHS  
Can sub to RoHS  
Must be RoHS  
RoHS  
Note: A direct substitution is a part with a different FRU part number that is automatically shipped by the  
distribution center at the time of order.  
8
ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2. General information  
This chapter provides some general information about your server.  
Features and specifications  
The following table provides information about the features and specifications of the server. Depending  
on the server model, some features might not be available, or some specifications might not apply. For  
information about your specific model, use the Setup Utility program. See “Using the Setup Utility program”  
on page 83.  
© Copyright Lenovo 2011  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Table 1. Features and specifications  
Microprocessor(s): Support up to two Intel® Xeon®  
dual-core, quad-core, or hex-core microprocessors  
(internal cache size varies by model type)  
Expansion  
• Two optical drive bays  
• Two hard disk drive bays  
• Two PCI card slots  
For the specific type and speed information about the  
microprocessor, use the Setup Utility program. See  
“Using the Setup Utility program” on page 83.  
• One PCI Express x1 card slot  
• One PCI Express x16 card slot  
For a list of supported microprocessors, go to  
http://www.lenovo.com/thinkserver and click Options  
under the Products tab.  
System management features  
• Ability to store power-on self-test (POST) hardware  
test results  
Memory  
• Automatic power-on startup  
• Supports up to four DDR3 ECC UDIMMs (double data  
rate 3 error correction code unbuffered dual inline  
memory modules)  
• Intel Active Management Technology (AMT)  
• Intel Hyper-Threading technology (some models)  
• Intel Rapid Storage Technology (RST)  
• Preboot Execution Environment (PXE)  
• System Management (SM) UEFI and SM software  
• Wake on LAN  
• Types: 1333 MHz, DDR3 registered SDRAM DIMMs  
Internal drives  
• Serial Advanced Technology Attachment (SATA) hard  
disk drive  
• Wake on Ring (in the Setup Utility program, this feature  
is called Serial Port Ring Detect for an external modem)  
• SATA optical drive  
Video subsystem  
Input/Output (I/O) features  
• Integrated graphics for a Video Graphics Array (VGA)  
connector and a DisplayPort connector  
• Eight Universal Serial Bus (USB) connectors (two on  
the front panel and six on the rear panel)  
Connectivity  
• One 9-pin serial port  
• 100/1000 Mbps integrated Ethernet controller  
• One Ethernet connector  
• One DisplayPort connector  
• One VGA monitor connector  
Power supply: Your server comes with one of the  
following power supplies:  
• 280–watt auto-sensing power supply  
• 320–watt auto-sensing power supply  
• Three audio connectors on the rear panel (audio line-in  
connector, audio line-out connector, and microphone  
connector)  
Preinstalled operating system  
Some models are preinstalled with one of the following  
operating systems:  
• Microsoft® Windows Server® 2008 R2 Foundation  
• Microsoft Windows® Small Business Server (SBS)  
Aurora  
Operating system(s), supported  
• Microsoft Windows Server 2008 R2 Foundation  
• Microsoft Windows Server 2008 R2 (Service Pack 1)  
• Microsoft Windows Small Business Server (SBS)  
Aurora  
• Microsoft Windows Small Business Server (SBS) 7  
• Microsoft Windows Multipoint Server  
10 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Table 1. Features and specifications (continued)  
Integrated functions:  
Environment  
• Ethernet controllers (The server comes with two  
integrated Gigabit Ethernet controllers, which support  
connection to 100 Mbps or 1000 Mbps network.)  
• One serial port  
• One Video Graphics Array (VGA) monitor connector  
• Six USB connectors (two front and four rear)  
• One RJ-45 Ethernet connectors on the rear panel  
• Eight diagnostic LEDs  
• Air temperature:  
Operating: 10°C to 35°C (50°F to 95°F)  
Non-operating: -40°C to 60°C (14°F to 140°F) (with  
package)  
Non-operating: -10°C to 60°C (14°F to 140°F)  
(without package)  
• Humidity:  
Size:  
Operating: 10% to 80% (non-condensing) (10%  
per hour)  
• Width: 174.8 mm (6.88 inches)  
• Height: 377.3 mm (14.85 inches)  
• Depth: 406.7 mm (16.01 inches)  
Non-operating: 10% to 90% (non-condensing)  
(10% per hour)  
Weight: Maximum configuration: 11.2 kg (24.7 lbs)  
• Altitude:  
Electrical input  
• Input voltage:  
– Low range:  
Operating: -50 to 10 000 ft (-15.2 to 3 048 m)  
Non-operating: -50 to 35 000 ft (-15.2 to 10 668 m)  
Security features  
Minimum: 90 V ac  
Maximum: 137 V ac  
– High range:  
• Computrace  
• Enabling or disabling a device  
• Enabling or disabling USB connectors individually  
• Hard disk drive password  
Minimum: 180 V ac  
Maximum: 264 V ac  
• Power-On Password (POP) and Administrator  
Password for UEFI access  
• Startup sequence control  
• Startup without keyboard or mouse  
• Support for an integrated cable lock (Kensington lock)  
• Support for a padlock  
• Trusted Platform Module (TPM)  
Software programs  
Lenovo provides software to help get your server up and running.  
EasyStartup  
The ThinkServer EasyStartup program simplifies the process of configuring RAID and installing supported  
Microsoft Windows and Linux operating systems and device drivers on your server. The EasyStartup program  
is provided with your server on the ThinkServer EasyStartup DVD. The DVD is self-starting (bootable). The  
user guide for the EasyStartup program is on the DVD and can be accessed directly from the program  
interface. For additional information, see “Using the ThinkServer EasyStartup program” on page 102.  
Reliability, availability, and serviceability  
Reliability, availability, and serviceability (hereafter referred to as RAS) are three important server design  
features. The RAS features help you to ensure the integrity of the data stored on the server, the availability of  
the server when you need it, and the ease with which you can diagnose and correct problems.  
The server has the following RAS features:  
Chapter 2. General information 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
• Advanced Configuration and Power Interface (ACPI)  
• Advanced Desktop Management Interface (DMI)  
• Automatic memory downsizing on error detection  
• Automatic restart on non-maskable interrupt (NMI)  
• Availability of microcode level  
• Built-in, menu-driven setup, system configuration, and RAID configuration  
• Built-in monitoring for fan, temperature, and voltage  
• Cooling fans with speed-sensing capability  
• ECC DDR3 SDRAM with Serial Presence Detect (SPD)  
• Error codes and messages to help you identify problems  
• Generating error logs for the power-on self-test (POST) failures  
• Hot-swap SAS hard disk drives  
• Integrated Ethernet controllers  
• Intelligent Platform Management Interface (IPMI) 2.0  
• Power-on self-test (POST)  
• Standby voltage for system-management features and monitoring  
• System-error light-emitting diode (LED) on the front panel  
• Vital product data (VPD), including the serial number information and replacement part numbers, stored in  
the nonvolatile memory for easier remote maintenance  
12 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3. Diagnostics and troubleshooting  
This chapter introduces some basic diagnostic and troubleshooting programs. If your server problem is not  
described here, see Appendix B “Help and service” on page 107 for additional troubleshooting resources.  
This chapter provides instructions on the following topics:  
•
•
•
“PC-Doctor for DOS” on page 13  
“Basic troubleshooting” on page 15  
“Troubleshooting tables” on page 16  
PC-Doctor for DOS  
The PC-Doctor for DOS diagnostic program is used to test hardware components of your server. It is also  
used to report operating-system-controlled settings that interfere with the correct operation of your server. If  
you are unable to isolate and repair the problem yourself after running the PC-Doctor for DOS diagnostic  
program, save and print the log files created by the PC-Doctor for DOS diagnostic program. You will need  
the log files when you speak to a Lenovo technical support representative.  
You can download the latest version of the PC-Doctor for DOS diagnostic program from  
http://www.lenovo.com/support. The PC-Doctor for DOS diagnostic program runs independently of the  
Windows operating system. Use the PC-Doctor for DOS diagnostic program if you are unable to start the  
Windows operating system. You can run the PC-Doctor for DOS diagnostic program from a diagnostic  
disc that you created.  
Creating a diagnostic disc  
This section provides instructions on how to create a diagnostic disc.  
To create a diagnostic disc, do the following:  
1. Download a self-starting bootable CD/DVD image (known as an ISO image) of the diagnostic program  
from http://www.lenovo.com/support.  
2. Use any CD/DVD burning software to create a diagnostic disc with the ISO image.  
Running the diagnostic program from a diagnostic disc  
This section provides instructions on how to run the diagnostic program from a diagnostic disc that you  
created.  
To run the diagnostic program from a diagnostic disc that you created, do the following:  
1. Make sure the optical drive you want to use is set as the first boot device in the startup device sequence.  
2. Make sure the server is turned on and then insert the disc into the optical drive. The diagnostic  
program opens.  
Note: You can insert the disc into the optical drive when you are setting the startup device sequence.  
However, if you insert the disc into the optical drive when you have already entered the operating  
system, you need to restart the server to access the diagnostic program.  
3. Follow the instructions on the screen to select the diagnostic test that you want to run.  
Note: For additional help, press the F1 key.  
© Copyright Lenovo 2011  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
4. Remove the diagnostic disc from the optical drive when you complete the diagnostic process.  
Navigating through the diagnostic program  
Use the cursor movement keys to navigate through the menus.  
• To select a menu item, press Enter.  
• To return to the previous menu, press Esc.  
• To view the help information system, press F1.  
Running tests  
There are four ways to run the diagnostic tests.  
• Using the cursor movement keys, select Run Normal Test or Run Quick Test from the Diagnostics menu  
and then press Enter. This automatically runs a pre-defined group of tests from each test category. By  
selecting Run Quick Test, a quick test will be started. By selecting Run Normal Test, a more extensive  
set of tests will be started and will take longer to complete.  
• Press F5 to automatically run all selected tests in all categories.  
• From within a test category, press Ctrl+Enter to automatically run only the selected tests in that category.  
• Using the cursor movement keys, highlight a single test within a test category, and then press Enter.  
This runs only that test.  
Press Esc at any time to stop the testing process.  
Test results (N/A, PASSED, FAILED, ABORTED) are displayed in the field beside the test description and in  
the test log. See “Viewing the test log” on page 15.  
To select one or more tests, do the following:  
1. Open the corresponding test category.  
2. Using the cursor movement keys, select the desired test.  
3. Press the space bar. A selected test is marked by >>. Pressing the space bar again de-selects a  
test and removes the >> mark.  
4. Repeat steps 2 and 3 above to select all desired tests.  
Test results  
Diagnostics test results produce the following error code format:  
Failure Type  
DeviceID  
Date  
Text  
Function Code  
ChkDigits  
• Function Code: Represents the feature or function within the server.  
• Failure Type: Represents the type of error encountered.  
• DeviceID: Contains the component's unit ID that corresponds to a certain disk drive, removable media  
drive, serial or parallel port, processor, specific RIMM, or a device on the PCI bus.  
• Date: Contains the date when the diagnostic test was run. The date is retrieved from CMOS and is  
displayed in the YYYYMMDD format.  
• ChkDigits: Contains a 2-digit check-digit value to ensure the following:  
– Diagnostics were run on the specified date.  
– Diagnostics were run on the specified server.  
– The diagnostic error code is recorded correctly.  
14 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
• Text: Description of the error.  
Note: See “POST error codes” on page 17 for error code listings.  
Formatting the hard disk drive  
The diagnostics program offers two hard disk drive formatting methods:  
• Quick Erase  
• Full Erase  
The quick erase method provides a DOS utility that performs the following:  
• Destroys the Master Boot Record (MBR) on the hard disk drive.  
• Destroys all copies of the FAT Table on all partitions (both the master and backup).  
• Destroys the partition table.  
• Provides messages that warn the user that this is a non-recoverable process.  
The full erase method provides a DOS utility that performs the following:  
• Performs all the steps in quick erase.  
• Provides a DOS utility that writes random data to all sectors of the hard disk drive.  
• Provides an estimate of time to completion along with a visual representation of completion status.  
• Provides messages that warn the user about a non-recoverable process.  
Important: Make sure that all data is backed up before using the quick erase or full erase function.  
To run a quick erase or full erase operation, do the following:  
1. Select the UTILITY option on the toolbar and press Enter.  
2. Select either the QUICK ERASE HARD DISK or FULL ERASE HARD DISK option and follow the  
instructions on the screen.  
Viewing the test log  
Errors reported by the diagnostic test will be displayed as a failure.  
To view details of a failure or to view a list of test results, use the following procedure from any test category  
screen:  
1. Press F3 to activate the log file.  
2. Press F3 again to save the file or press F2 to print the file.  
Basic troubleshooting  
The following tables provide information to help you troubleshoot your server problems.  
Note: If you cannot correct the problem, have the server serviced. For a list of service and support telephone  
numbers, refer to the Warranty and Support Information document at:  
http://www.lenovo.com/support/phone  
General problems  
The following table describes the general problems and suggested actions to correct detected problems.  
Chapter 3. Diagnostics and troubleshooting 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Symptom  
Action  
The server does not start when  
you press the power switch.  
Verify that:  
• The power cord is correctly connected to the rear of the server and to a working  
electrical outlet.  
• If your server has a secondary power switch on the rear of the server, make sure  
that it is switched on.  
• The power indicator on the front of the server is on.  
• The server voltage matches the voltage available at the electrical outlet for your  
country or region.  
The monitor screen is blank.  
Verify that:  
• The monitor signal cable is correctly connected to the monitor and to the  
appropriate monitor connector on the server.  
• The monitor power cord is correctly connected to the monitor and to a working  
electrical outlet.  
• The monitor is turned on and the brightness and contrast controls are set  
correctly.  
• The server voltage matches the voltage available at the electrical outlet for your  
country or region.  
• If your server has two monitor connectors, be sure to use the connector on  
the graphics card.  
The operating system does not  
start.  
Verify that the startup sequence includes the device where the operating system  
resides. Usually, the operating system is on the hard disk drive. For more  
information, see “Selecting a startup device” on page 99.  
The server beeps multiple times Verify that no keys are stuck.  
before the operating system  
starts.  
Troubleshooting tables  
Use the troubleshooting tables to find solutions to problems that have identifiable symptoms.  
If you have just added new software or a new optional device and the server is not working, do the following  
before using the troubleshooting tables:  
1. Check the system-error LED on the operator information panel to see if it is lit.  
2. Remove the software or device that you just added.  
3. Run the diagnostic tests to determine whether the server is running correctly.  
4. Reinstall the new software or new device.  
Hard disk drive boot error  
A hard disk drive boot error can have the following causes.  
Symptom  
FRU/Action  
The startup drive is not in the boot sequence in  
configuration.  
Check the configuration and ensure the startup drive is  
in the boot sequence.  
No operating system is installed on the boot drive.  
Install an operating system on the boot drive.  
16 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Symptom  
FRU/Action  
The boot sector on the startup drive is corrupted.  
The drive must be formatted. Do the following:  
1. Attempt to back up the data on the failing hard disk  
drive.  
2. Using the operating system programs, format the  
hard disk drive.  
The drive is defective.  
Replace the hard disk drive.  
Power supply problems  
If you suspect a power supply problem, use the following procedures.  
Check/Verify  
FRU/Action  
Reseat connectors.  
Check the following for proper installation.  
• Power cord  
• On/Off switch connector  
• On/Off switch power supply connector  
• System board power supply connectors  
• Microprocessor connection  
Power cord  
Check the power cord for continuity.  
Power-on switch  
Check the power-on switch for continuity.  
Beep symptoms  
Beep symptoms are tones or a series of tones separated by pauses (intervals without sound) during the POST.  
The following table describes beep symptoms and provides suggested actions to correct detected problems.  
Symptom  
Error  
FRU/Action  
3 short beeps and 1 long beep  
Memory not detected  
Perform the following actions in order:  
1. Make sure that the memory  
module(s) are properly seated in  
the connector(s).  
2. Replace the memory module(s).  
3. Replace the system board.  
2 short beeps  
Indicates that an error has occurred  
during the POST.  
Common POST error  
POST error codes  
Each time you turn on the system, it performs a series of tests that checks the operation of the system and  
options. This series of tests is called the power-on self-test, or POST.  
The POST performs the following operations:  
• Checks some basic system board operations  
• Checks the memory operation  
• Checks the video operation  
• Verifies that the boot drive is working  
Chapter 3. Diagnostics and troubleshooting 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
If the POST detects a problem, an error message will be displayed on the screen. A single problem can  
cause several error messages. When you correct the cause of the first error message, probably the other  
error messages will not be displayed the next time you turn on the computer.  
POST error code  
POST error message  
Description/Action  
This error message is displayed when the machine  
type or the serial number is invalid.  
00CE  
Machine Type or Serial Number is INVALID  
0210  
0211  
0135  
This error message is displayed when a key is kept  
pressed for a long time.  
Stuck key  
Keyboard not found  
Fan failure  
This error message is displayed when there is no  
keyboard detected.  
The system might be overheating.  
Press F1 to enter the Setup Utility program. Then  
press F10 to save the operation and exit the Setup  
Utility program.  
Note: If the problem is caused by the  
microprocessor fan, pressing F10 will not solve  
the problem.  
0164  
1762  
1820  
Memory size decreased  
This error message is displayed when the memory  
size has decreased.  
Press F1 to enter the Setup Utility program. Then  
press F10 to save the operation and exit the Setup  
Utility program.  
This error message is displayed when a hard disk  
drive or optical drive change has been made.  
Configuration change has occurred  
Press F1 to enter the Setup Utility program. Then  
press F10 to save the operation and exit the Setup  
Utility program.  
More than one external fingerprint reader  
is attached. Power off and remove all but  
If more than one external fingerprint reader is  
connected to a computer, this error message will  
the reader that you set up within your main be displayed to inform you to remove all of the  
operating system.  
fingerprint keyboards except the one compatible  
with the fingerprint application on your computer.  
1962  
0162  
No operating system found. Press any key  
to repeat boot sequence.  
This error occurs only after the POST is completed.  
Press any key to repeat boot sequence.  
Setup data integrity check failure  
Press F1 to enter the Setup Utility program. Then  
press F10 to save the operation and exit the Setup  
Utility program.  
0167  
0175  
No processor microcode update found  
System security - Security data corrupted  
This error message indicates that there is  
no microcode update image for the current  
microprocessor.  
Press F1 to enter the Setup Utility program. Then  
press F10 to save the operation and exit the Setup  
Utility program.  
18 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
POST error code  
POST error message  
Description/Action  
0176  
This error message is displayed when the  
computer is turned on with the cover open or  
removed.  
System security - The system has been  
tampered with  
Press F1 to enter the Setup Utility program. Then  
press F10 to save the operation and exit the Setup  
Utility program.  
0189  
System security - Can not read the  
Security EEPROM  
This error message indicates that the Security  
EEPROM might be broken or have been removed.  
Press F1 to enter the Setup Utility program. Then  
press F10 to save the operation and exit the Setup  
Utility program.  
0197  
0190  
0199  
System security - Unauthorized security  
data change detected  
Press F1 to enter the Setup Utility program. Then  
press F10 to save the operation and exit the Setup  
Utility program.  
System security - Invalid security change  
requested  
Press F1 to enter the Setup Utility program. Then  
press F10 to save the operation and exit the Setup  
Utility program.  
System security - Security password retry Press F1 to enter the Setup Utility program. Then  
count exceeded  
press F10 to save the operation and exit the Setup  
Utility program.  
EasyStartup problems  
The following table describes the EasyStartup problems and provides suggested actions to correct detected  
problems.  
Table 2. ThinkServer EasyStartup DVD  
Follow the suggested actions in the order in which they are listed in the Action column until the problem  
is resolved.  
Action  
Symptom  
The ThinkServer  
EasyStartup DVD will  
not start.  
• Make sure the server supports the EasyStartup program and has a startable (bootable)  
DVD drive.  
• If the startup (boot) sequence settings have been changed, make sure the DVD drive  
is first in the startup sequence.  
• If more than one DVD drive is installed, make sure that only one DVD drive is set as the  
primary drive. Start the EasyStartup DVD from the primary DVD drive.  
The operating system  
installation program  
continuously loops.  
Make more space available on the hard disk drive.  
The EasyStartup  
program will not start  
the operating system  
medium.  
Make sure that the operating system medium is supported by the EasyStartup program.  
See the EasyStartup User Guide for a list of supported operating system versions. The  
EasyStartup User Guide and compatibility notes are available through the EasyStartup  
program.  
Chapter 3. Diagnostics and troubleshooting 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Miscellaneous error messages  
Symptom  
FRU/Action  
Changing display colors  
Display/Monitor  
1. Power switch  
Computer will not turn off. See “Hard disk drive boot  
error” on page 17.  
2. System board  
3. Riser card, if installed.  
Computer will not RPL from server  
1. Ensure that Network is set as the first device or it is  
after CD/DVD in the startup sequence.  
2. Ensure that the network adapter is enabled for RPL.  
3. Network adapter (Advise the network administrator  
of new MAC address)  
Computer will not perform a Wake On LAN® (if applicable)  
1. Check the power supply and signal cable connections  
to the network adapter.  
2. Ensure that the operating system settings are set to  
enable Wake on LAN.  
3. Ensure that the Wake On LAN feature is enabled in  
Setup/Configuration (see “Starting the Setup Utility  
program” on page 83.)  
4. Ensure that the network administrator is using the  
correct MAC address.  
5. Ensure that no interrupt or I/O address conflicts.  
6. Check the network adapter.  
1. Power supply  
Dead computer. See “Hard disk drive boot error” on page  
17.  
2. System board  
Diskette drive in-use light remains on or does not light  
when drive is active.  
1. Diskette drive  
2. System board  
3. Diskette drive cable  
Blank screen except for flashing cursor.  
Incorrect memory size during POST  
1. System board  
2. Primary hard disk drive  
3. Hard disk drive cable  
1. Run the memory tests.  
2. Check the memory modules.  
3. Check the system board.  
"Insert a Diskette" icon appears with a known-good  
diagnostics diskette in the first 3.5-inch diskette drive.  
1. System board  
2. Diskette drive cable  
3. Network adapter  
1. Display  
Intensity or color varies from left to right of characters  
and color bars  
2. Video adapter (if present)  
3. System board  
No power or fan not running  
See “Hard disk drive boot error” on page 17.  
1. Diskette drive  
Non-system disk or disk error-type message with a  
known-good diagnostic diskette.  
2. System board  
3. Diskette drive cable  
20 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Symptom  
FRU/Action  
1. Display  
Other display symptoms not listed above (including blank  
or illegible display)  
2. System board  
Turn on indicator or hard disk drive in-use light not on, but  
computer works correctly  
1. Power switch/LED assembly  
2. System board  
Printer problems  
1. Printer  
2. System board  
Program loads from the hard disk with a known-good  
diagnostics diskette in the first 3.5-inch diskette drive  
1. Run the Setup Utility program and check startup  
sequence.  
2. Check the diskette drive.  
3. Check the diskette drive cable.  
4. Check the system board.  
5. Check the power supply.  
RPL computer cannot access programs from its own hard  
disk drive.  
1. If the network administrator is using the LCCM Hybrid  
RPL, check startup sequence:  
a. First device - Network  
b. Second device - Hard disk drive  
2. Check the hard disk drive.  
RPL computer does not RPL from server  
1. Check the startup sequence.  
2. Check the network adapter LED status.  
Serial or parallel port device failure (system board port)  
1. Run an external device self-test.  
2. Check the external device.  
3. Check the cable.  
4. Check the system board.  
Serial or parallel port device failure (adapter port)  
1. Run an external device self-test.  
2. Check the external device.  
3. Check the cable.  
4. Check the alternate adapter.  
5. Check the system board.  
1. Keyboard  
Some or all keys on the keyboard do not work  
2. Keyboard cable  
3. System board  
Undetermined problems  
This topic provides instructions on how to find out the failing components.  
To find out the failing components, do the following:  
1. Turn off the server.  
2. Remove or disconnect the following components (if installed) one at a time.  
a. External devices (modem, printer, or mouse)  
b. Any adapters  
c. Memory modules  
d. Extended video memory  
Chapter 3. Diagnostics and troubleshooting 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
e. External cache  
f. External cache RAM  
g. Hard disk drive  
h. Diskette drive  
3. Turn on the server to re-test the system.  
4. Repeat steps 1 through 3 until you find the failing components. If all devices and adapters have been  
removed, and the problem continues, replace the system board.  
22 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4. Locating parts, controls, LEDs, and connectors  
This chapter provides information to help you locate your server parts, controls, light-emitting diodes  
(LEDs), and connectors.  
Front view  
Figure 1 “Front control and connector locations” on page 23 shows the locations of the controls and  
connectors on the front of your server.  
Figure 1. Front control and connector locations  
4 Power switch  
1 Optical drive eject/close button  
2 Hard disk drive activity LED  
3 Power-on LED  
5 USB connectors (2)  
Front control panel LEDs  
The following table describes the meaning of the LEDs on the front control panel.  
© Copyright Lenovo 2011  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Table 3. Front control panel LEDs  
LED  
State  
On  
Color  
Green  
Green  
Description  
The server power is on.  
Power LED  
Blinking  
The server power is in ACPI S1 mode, which is also  
known as Power On Suspend (POS) mode. In this mode,  
the microprocessor is not working while other hardware  
devices are still working.  
Off  
Off  
Off  
Off  
The server power is off.  
Hard disk drive  
LED  
The hard disk drive is not active.  
The hard disk drive is active.  
Blinking  
Green  
Rear view  
Figure 2 “Rear connector locations” on page 24 shows the locations of the connectors on the rear of  
your server. Some connectors on the rear of your server are color-coded to help you determine where to  
connect the cables in your server.  
Figure 2. Rear connector locations  
1 Power cord connector  
2 Serial port  
7 Microphone connector  
8 Audio line-out connector  
9 Audio line-in connector  
10 PCI Express x16 card slot  
11 PCI Express x1 card slot  
12 PCI card slots (2)  
3 VGA monitor connector  
4 DisplayPort connector  
5 USB connectors (6)  
6 Ethernet connector  
24 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Connector  
Description  
Audio line-in connector  
Used to receive audio signals from an external audio device, such as a stereo  
system. When you attach an external audio device, a cable connects the audio  
line-out connector of the device to the audio line-in connector of the server.  
Audio line-out connector  
Used to send audio signals from the server to external devices, such as powered  
stereo speakers (speakers with built-in amplifiers), headphones, multimedia  
keyboards, or the audio line-in connector on a stereo system or other external  
recording device.  
DisplayPort connector  
Ethernet connector  
Used to attach a high-performance monitor, a direct-drive monitor, or other devices  
that use a DisplayPort connector.  
Used to attach an Ethernet cable for a local area network (LAN).  
Note: To operate the server within FCC Class B limits, use a Category 5 Ethernet  
cable.  
Microphone connector  
Serial port  
Used to attach a microphone to your server when you want to record sound or if  
you use speech-recognition software.  
Used to attach an external modem, a serial printer, or other devices that use a  
9-pin serial port.  
USB connector  
Used to attach a device that requires a USB connector, such as a USB keyboard, a  
USB mouse, a USB scanner, or a USB printer. If you have more than eight USB  
devices, you can purchase a USB hub, which you can use to connect additional  
USB devices.  
VGA monitor connector  
Used to attach a VGA monitor or other devices that use a VGA monitor connector.  
Chapter 4. Locating parts, controls, LEDs, and connectors 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Locating parts on the system board  
Figure 3 “System board part locations” on page 26 shows the locations of the parts on the system board.  
Figure 3. System board part locations  
1 4-pin power connector  
14 Front panel connector for power switch and LED indicators  
2 Microprocessor fan connector  
15 Front USB connector 1 (for connecting USB port 1 and 2  
on the front bezel)  
3 Memory slot 1 (DIMM1)  
16 Front USB connector 2 (for connecting additional USB  
devices)  
4 Memory slot 2 (DIMM2)  
17 Clear CMOS (Complementary Metal Oxide Semiconductor)  
/Recovery jumper  
18 Internal speaker connector  
5 Memory slot 3 (DIMM3)  
6 Memory slot 4 (DIMM4)  
19 Front audio connector (for connecting the microphone and  
headphone connectors on the front bezel)  
7 Thermal sensor connector  
8 24-pin power connector  
9 Battery  
20 PCI card slots (2)  
21 PCI Express x1 card slot  
22 PCI Express x16 graphics card slot  
23 Rear fan connector  
10 SATA connectors 1 and 2 (SATA 3.0  
connectors)  
11 SATA connector 3 (SATA 2.0 connector)  
12 eSATA connector  
24 Cover presence switch connector (Intrusion switch connector)  
25 Microprocessor  
13 Front fan connector  
26 PS/2 keyboard and mouse connector  
26 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Internal components  
Figure 4 “Component locations” on page 27 shows the locations of the various components in your server. To  
remove the server cover and access to the inside of the server, see “Removing the server cover” on page 33.  
Figure 4. Component locations  
1
7
Heat sink  
Secondary hard disk drive (installed in some  
models)  
2
3
4
5
6
8
Microprocessor  
Memory modules  
Optical drive  
Primary hard disk drive  
System board  
9
10  
11  
Rear fan assembly  
Power supply  
Front bezel  
Front fan assembly  
Chapter 4. Locating parts, controls, LEDs, and connectors 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
28 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5. Replacing FRUs  
This chapter provides detailed instructions for replacing FRUs in the server.  
FRU replacements are to be done only by trained service technicians.  
This chapter does not contain the remove or replace procedure for all FRUs. Only the major FRUs are  
documented.  
Guidelines  
This section provides some guidelines that you should read and understand before using your server.  
Basic guidelines  
Before you use the server, be sure to read and understand the following guidelines:  
• Be sure to read and understand the Safety Information and the Warranty and Support Information on the  
ThinkServer Documentation DVD that comes with your product, and “Guidelines” on page 29. These  
information will help you work safely. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
• When you install your new server, take the opportunity to download and apply the most recent firmware  
updates. This step will help to ensure that any known issues are addressed and that your server is  
ready to function at maximum levels of performance. To download firmware updates for your server,  
do the following:  
1. Go to http://www.lenovo.com/support.  
2. Click Download & Drivers → ThinkServer and then follow the instructions on the Web page to  
download firmware updates for your server.  
• Before you install optional hardware devices, make sure that the server is working correctly. If an operating  
system is installed, turn on the server and make sure that the operating system starts. If no operating  
system is installed, make sure that a 19990305 error code is displayed, indicating that an operating  
system was not found but the server is working correctly. If the server is not working correctly, refer to the  
chapter Chapter 3 “Diagnostics and troubleshooting” on page 13 for detailed diagnostic information.  
• Observe good housekeeping in the area where you are working. Put removed covers and other parts  
in a safe place.  
• If you must turn on the server while the server cover is removed, make sure that no one is near the server  
and that no tools or other objects have been left inside the server.  
• Do not attempt to lift an object that you think is too heavy for you. If you have to lift a heavy object,  
observe the following precautions:  
– Make sure that you can stand safely without slipping.  
– Distribute the weight of the object equally between your feet.  
– Use a slow lifting force. Never move suddenly or twist when you lift a heavy object.  
– To avoid straining the muscles in your back, lift by standing or by pushing up with your leg muscles.  
• Make sure that you have an adequate number of properly grounded electrical outlets for the server,  
monitor, and other devices.  
• Back up all important data before you make changes to drives.  
• Have a small flat-blade screwdriver available.  
© Copyright Lenovo 2011  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
• To view the error LEDs on the system board and internal components, leave the server connected to  
power.  
• You do not have to turn off the server to install or replace hot-swap fans, redundant hot-swap ac power  
supplies, or hot-plug USB devices. However, you must turn off the server before performing any steps that  
involve installing, removing, or replacing adapter cables or non-hot-swap optional devices or components.  
• After completing any installation, removal, or replacement procedure, reinstall all safety shields, guards,  
labels, and ground wires.  
• For a list of supported optional devices for the server, go to http://www.lenovo.com/thinkserver.  
• When working inside the server, you might find some tasks easier if you lay the server on its side. You  
might need to first pivot the foot stands inward and then lay the computer on its side.  
System reliability guidelines  
To help ensure proper cooling and system reliability, make sure that you follow these guidelines:  
• Every drive bay has an internal drive installed or an Electro Magnetic Compatibility (EMC) shield installed.  
• If the server has redundant power, every power supply bay has a power supply assembly installed.  
• Leave adequate space around the server to make sure that the server cooling system works well.  
• Properly route the cables. For some options, such as PCI cards, follow the cabling instructions that  
come with the options.  
• Make sure that you replace a failed fan within 48 hours.  
• When replacing a hot-swap drive, install the new hot-swap drive within two minutes of removal.  
• Do not remove any air duct or air baffles while the server is running. Operating the server without the  
air duct or air baffles might cause the microprocessor to overheat.  
• The second microprocessor socket always contains either a microprocessor socket cover or a  
microprocessor and heat sink.  
Handling static-sensitive devices  
Attention:  
Do not open the static-protective package containing the new part until the defective part has been removed from the  
server and you are ready to install the new part. Static electricity, although harmless to you, can seriously damage  
server components and parts.  
When you handle server parts and components, take these precautions to avoid static-electricity damage:  
• Limit your movement. Movement can cause static electricity to build up around you.  
• Wear an electrostatic-discharge wrist strap, if one is available.  
• Always carefully handle the parts and other components (such as PCI cards, memory modules, system  
boards, and microprocessors) by its edges or its frame. Do not touch solder joints, pins, or exposed  
circuitry.  
• Prevent others from touching the parts and other computer components.  
• Before you replace a new part, touch the static-protective package containing the new part to a metal  
expansion-slot cover or other unpainted metal surface on the server for at least two seconds. This  
reduces static electricity from the package and your body.  
• Remove the new part from the static-protective package and directly install it in the server without  
placing it on any other surface. If it is hard for you to do this in your specific situation, place the  
static-protective package of the new part on a smooth, level surface, and then place the new part on  
the static-protective package.  
• Do not place the part on the server cover or other metal surface.  
30 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
• Take additional care when handling devices during cold weather. Heating reduces indoor humidity  
and increases static electricity.  
Working inside the server with the power on  
Attention:  
Static electricity that is released to internal server components when the server is turned on might cause the server to  
halt, which might result in the loss of data. To avoid this potential problem, always use an electrostatic-discharge wrist  
strap or other grounding system when you work inside the server with the power on.  
The server supports hot-swap devices and is designed to operate safely while it is turned on and the cover is  
removed. Follow these guidelines when you work inside the server with the power on:  
• Avoid wearing loose-fitting clothing on your forearms. Button long-sleeved shirts before working inside  
the server; do not wear cuff links while you are working inside the server.  
• Do not allow your necktie or scarf to hang inside the server.  
• Remove jewelry, such as bracelets, necklaces, rings, and loose-fitting wrist watches.  
• Remove items from your shirt pocket, such as pens and pencils. These items might fall into the server as  
you lean over it.  
• Avoid dropping any metallic objects into the server, such as paper clips, hairpins, and screws.  
Guidelines for trained service technicians  
This section contains information for trained service technicians.  
Inspecting for unsafe conditions  
Use the information in this section to help you identify potential unsafe conditions in a Lenovo product that  
you are working on. Each Lenovo product, as it was designed and manufactured, has required safety items  
to protect users and service technicians from injury. The information in this section addresses only those  
items. Use good judgment to identify potential unsafe conditions that might be caused by non-Lenovo  
alterations or attachment of non-Lenovo features or options that are not addressed in this section. If you  
identify an unsafe condition, you must determine how serious the hazard is and whether you must correct  
the problem before you work on the product.  
Consider the following conditions and the safety hazards that they present:  
• Electrical hazards, especially primary power. Primary voltage on the frame can cause serious or fatal  
electrical shock.  
• Explosive hazards, such as a damaged CRT face or a bulging capacitor.  
• Mechanical hazards, such as loose or missing hardware.  
To inspect the product for potential unsafe conditions, complete the following steps:  
1. Make sure that the power is off and the power cord is disconnected.  
2. Make sure that the exterior cover is not damaged, loose, or broken, and observe any sharp edges.  
3. Check the power cord:  
• Make sure that the third-wire ground connector is in good condition. Use a meter to measure  
third-wire ground continuity for 0.1 ohm or less between the external ground pin and the frame ground.  
• Make sure that the power cord is the correct type.  
• Make sure that the insulation is not frayed or worn.  
Chapter 5. Replacing FRUs 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
4. Remove the cover.  
5. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo  
alterations.  
6. Check inside the server for any obvious unsafe conditions, such as metal filings, contamination, water or  
other liquid, or signs of fire or smoke damage.  
7. Check for worn, frayed, or pinched cables.  
8. Make sure that the power-supply cover fasteners (screws or rivets) have not been removed or tampered  
with.  
Guidelines for servicing electrical equipment  
Observe the following guidelines when servicing electrical equipment:  
• Check the area for electrical hazards such as moist floors, nongrounded power extension cords, power  
surges, and missing safety grounds.  
• Use only approved tools and test equipment. Some hand tools have handles that are covered with a soft  
material that does not provide insulation from live electrical currents.  
• Regularly inspect and maintain your electrical hand tools for safe operational condition. Do not use  
worn or broken tools or testers.  
• Do not touch the reflective surface of a dental mirror to a live electrical circuit. The surface is conductive  
and can cause personal injury or equipment damage if it touches a live electrical circuit.  
• Some rubber floor mats contain small conductive fibers to decrease electrostatic discharge. Do not use  
this type of mat to protect yourself from electrical shock.  
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.  
• Locate the emergency power-off (EPO) switch, disconnecting switch, or electrical outlet so that you can  
turn off the power quickly in the event of an electrical accident.  
• Disconnect all power before you perform a mechanical inspection, work near power supplies, or remove  
or install main units.  
• Before you work on the equipment, disconnect the power cord. If you cannot disconnect the power  
cord, have the customer power-off the wall box that supplies power to the equipment and lock the  
wall box in the off position.  
• Never assume that power has been disconnected from a circuit. Check it to make sure that it has been  
disconnected.  
• If you have to work on equipment that has exposed electrical circuits, observe the following precautions:  
– Make sure that another person who is familiar with the power-off controls is near you and is available to  
turn off the power if necessary.  
– When you are working with powered-on electrical equipment, use only one hand. Keep the other  
hand in your pocket or behind your back to avoid creating a complete circuit that could cause an  
electrical shock.  
– When you use a tester, set the controls correctly and use the approved probe leads and accessories  
for that tester.  
– Stand on a suitable rubber mat to insulate you from grounds such as metal floor strips and equipment  
frames.  
• Use extreme care when you measure high voltages.  
• To ensure proper grounding of components such as power supplies, pumps, blowers, fans, and motor  
generators, do not service these components outside of their normal operating locations.  
• If an electrical accident occurs, use caution, turn off the power, and send another person to get medical  
aid.  
32 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Removing the server cover  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to remove the server cover.  
CAUTION:  
Turn off the server and wait three to five minutes to let the server cool before removing the server  
cover.  
To remove the server cover, do the following:  
1. Remove any media from the drives and turn off all attached devices and the server.  
2. Disconnect all power cords from electrical outlets.  
3. Disconnect the power cords, Input/Output (I/O) cables, and any other cables that are connected to the  
server. See “Front view” on page 23 and “Rear view” on page 24.  
4. Remove any locking device that secures the server cover, such as a padlock or an integrated cable lock.  
5. Remove the two thumbscrews that secure the server cover.  
6. Press the cover-release button on the side of the server and slide the cover to the rear of the server  
to remove the cover.  
Figure 5. Removing the server cover  
Chapter 5. Replacing FRUs 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Removing and reinstalling the front bezel  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to remove and reinstall the front bezel.  
To remove and reinstall the front bezel, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. Remove the front bezel by releasing the three plastic tabs on the left side and pivoting the front bezel  
outward.  
Figure 6. Removing the front bezel  
34 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
4. To reinstall the front bezel, align the three plastic tabs on the right side of the front bezel with the  
corresponding holes in the chassis, then pivot the front bezel inward until it snaps into position on  
the left side.  
Figure 7. Reinstalling the front bezel  
What to do next:  
• To work with another piece of hardware, go to the appropriate section.  
• To complete the installation or replacement, go to “Completing the parts replacement” on page 66.  
Installing, removing, or replacing optional hardware devices  
This section provides instructions on how to install, remove, or replace optional hardware devices for your  
server. You can expand the capabilities of your server by adding memory modules, PCI cards, or drives,  
and maintain your server by replacing the failing optional hardware devices. If you are replacing an optional  
hardware device, perform the removal procedure and then perform the installation procedure for the optional  
hardware device that you want to replace.  
Installing or replacing a PCI card  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to install or replace a PCI card.  
Your server has two standard PCI card slots, one PCI Express x1 card slot, and one PCI Express x16  
card slot.  
Chapter 5. Replacing FRUs 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
To install or replace a PCI card, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. At the rear of the server, press the release button 1 to open the PCI card latch 2 .  
Figure 8. Opening the PCI card latch  
36 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. If you are installing a PCI card, remove the appropriate metal slot cover. If you are replacing an old PCI  
card, grasp the old card that is currently installed and gently pull it out of the slot.  
Notes:  
a. The PCI card fits tightly into the card slot. If necessary, alternate moving each side of the card a  
small and equal amount until it is completely removed from the card slot.  
b. If the PCI card is held in place by a retaining latch, press the card retaining latch 1 as shown to  
disengage the latch. Grasp the PCI card and gently pull it out of the card slot.  
Figure 9. Removing a PCI card  
5. Remove the new PCI card from its static-protective package.  
6. Install the new PCI card into the appropriate slot on the system board. See “Locating parts on the  
system board” on page 26.  
Note: If you are installing a PCI Express x16 card, make sure the memory slot retaining clips are closed  
before you install the PCI Express x16 card.  
Chapter 5. Replacing FRUs 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Pivot the PCI card latch to the closed position to secure the PCI card.  
Figure 10. Installing a PCI card  
What to do next:  
• To work with another piece of hardware, go to the appropriate section.  
• To complete the installation or replacement, go to “Completing the parts replacement” on page 66.  
Installing or removing the Ethernet card  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to install or remove the Ethernet card. Use any documentation that  
came with the Ethernet card and follow those instructions in addition to the instructions in this section.  
To install or remove the Ethernet card, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. Lay the server on its side for easier operation.  
4. The Ethernet card is a kind of PCI card. See “Installing or replacing a PCI card” on page 35 and follow  
those instructions to install or remove the Ethernet card.  
5. If you are instructed to return the removed Ethernet card to the manufacturer, follow all packaging  
instructions and use any packaging materials that are supplied to you for shipping.  
38 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
If you are using the Microsoft Windows operating systems, you need to install the device driver for the  
Ethernet card. To install the device driver on Windows operating systems, do the following:  
1. Save any open documents and exit all applications.  
2. Insert the ThinkServer EasyStartup DVD that came with your server into the DVD drive.  
Note: You do not need to use the driver disc that came with the Ethernet card.  
3. Right-click My Computer and select Properties. The System Properties window opens.  
4. On the Hardware tab, click the Device Manager button. The Device Manager window opens.  
5. Expand Network adapters and then right-click one of the Ethernet cards (PRO/1000PT or the yellow  
question mark).  
6. Select Update Driver.... The Hardware Update Wizard program opens.  
7. Select Install the software automatically (Recommended) and click Next to continue.  
8. Follow the instructions on the screen.  
What to do next:  
• To work with another piece of hardware, go to the appropriate section.  
• To complete the installation, go to “Completing the parts replacement” on page 66.  
Installing or removing a memory module  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to install or remove a memory module.  
Your server has four slots for installing or replacing DDR3 UDIMMs that provide up to a maximum of 16 GB  
system memory. When installing or replacing a memory module, use the following guidelines:  
• Use 1 GB, 2 GB, or 4 GB DDR3 UDIMMs in any combination up to a maximum of 16 GB.  
• Install memory modules in the sequence of DIMM 1, DIMM 3, DIMM 2, and DIMM 4. See “Locating  
parts on the system board” on page 26.  
To install or replace a memory module, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. Lay the server on its side for easier access to the system board.  
4. Locate the memory slots. See “Locating parts on the system board” on page 26.  
5. Remove any parts that might prevent your access to the memory slots. Depending on your server  
model, you might need to remove the PCI Express x16 graphics card for easier access to the memory  
slots. See “Installing or replacing a PCI card” on page 35.  
6. Depending on whether you are installing or replacing a memory module, do one of the following:  
Chapter 5. Replacing FRUs 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
• If you are replacing an old memory module, open the retaining clips and gently pull the memory  
module out of the memory slot.  
Figure 11. Removing a memory module  
• If you are installing a new memory module, open the retaining clips of the memory slot into which you  
want to install the memory module.  
Figure 12. Opening the retaining clips  
7. Touch the static-protective package that contains the new memory module to any unpainted metal  
surface on the outside of the server. Then, remove the new memory module from the package.  
40 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Position the new memory module over the memory slot. Make sure that the notch 1 on the new memory  
module is aligned with the key 2 in the memory slot. Then, press the new memory module straight down  
into the memory slot until the retaining clips close and the new memory module snaps into position.  
Note: If there is a gap between the memory module and the retaining clips, the memory module has  
not been correctly installed. Open the retaining clips, remove the memory module, and then reinstall it  
into the slot.  
Figure 13. Installing a memory module  
9. Reinstall the PCI Express x16 graphics card if you have removed it.  
What to do next:  
• To work with another piece of hardware, go to the appropriate section.  
• To complete the installation or replacement, go to “Completing the parts replacement” on page 66.  
Installing or replacing the optical drive  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to install or replace the optical drive.  
To install or replace an optical drive, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 34.  
4. Depending on whether you are installing or replacing an optical drive, do one of the following:  
• If you are installing a secondary optical drive, remove the plastic panel in the front bezel for the  
drive bay you want to use. If there is a metal static shield installed in the drive bay, remove the  
metal static shield.  
Chapter 5. Replacing FRUs 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
• If you are replacing an optical drive, disconnect the signal cable and the power cable from the rear  
of the optical drive, press the blue release button and then slide the optical drive out of the front of  
the server.  
Figure 14. Removing the optical drive  
5. Slide the new optical drive with the optical drive retainer 1 installed into the drive bay from the front of  
the server until the optical drive snaps into position.  
Figure 15. Installing the optical drive  
42 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 34.  
7. Connect one end of the signal cable to the optical drive and the other end to an available SATA  
connector on the system board. See “Locating parts on the system board” on page 26. Then, locate an  
available five-wire power connector and connect it to the SATA drive.  
Figure 16. Connecting a SATA optical drive  
What to do next:  
• To work with another piece of hardware, go to the appropriate section.  
• To complete the installation or replacement, go to “Completing the parts replacement” on page 66.  
Replacing the primary hard disk drive  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to replace the primary hard disk drive.  
To replace the primary hard disk drive, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. Locate the primary hard disk drive. See “Locating parts on the system board” on page 26.  
4. Disconnect the signal cable and the power cable from the rear of the hard disk drive.  
Chapter 5. Replacing FRUs 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Press the blue release tab 1 downward, slide the hard disk drive cage 2 to the rear of the server, and  
then pivot it outward to completely remove the drive cage from the chassis. Then, pull on the blue  
handle 3 to remove the hard disk drive from the drive cage.  
Figure 17. Removing the primary hard disk drive  
6. Flex the sides of the blue bracket to remove the hard disk drive from the bracket.  
7. To install a new hard disk drive into the blue bracket, flex the sides of the bracket and align pin 1 , pin 2 ,  
pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the  
circuit board 5 on the bottom of the hard disk drive.  
Note: If you are installing a 2.5-inch hard disk drive, install the hard disk drive into a 2.5-inch to 3.5-inch  
hard disk drive tray first and then install the tray into the blue bracket.  
Figure 18. Installing the hard disk drive into the bracket  
44 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Slide the new hard disk drive with the blue bracket into the drive cage until it snaps into position and  
align the hard disk drive cage pivot pin with the slot 1 in the upper drive cage. Then, slide the hard disk  
drive cage into the chassis. Press down on the metal latch 2 and pivot the hard disk drive cage into  
place. Then, slide the drive cage to the front of the server until it snaps into position.  
Note: There are two arrows, one on the upper drive cage and one on the hard disk drive cage. The  
arrows are aligned when the hard disk drive is in the correct position.  
Figure 19. Installing the primary hard disk drive  
Chapter 5. Replacing FRUs 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Connect one end of the signal cable to the hard disk drive and the other end to an available SATA  
connector on the system board. See “Locating parts on the system board” on page 26. Then, locate an  
available five-wire power connector and connect it to the hard disk drive.  
Figure 20. Connecting a SATA hard disk drive  
What to do next:  
• To work with another piece of hardware, go to the appropriate section.  
• To complete the replacement, go to “Completing the parts replacement” on page 66.  
Installing or replacing the secondary hard disk drive  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
To install or replace the secondary hard disk drive, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. Locate the secondary hard disk drive. See “Locating parts on the system board” on page 26 and  
“Internal components” on page 27.  
4. If you are replacing the secondary hard disk drive, disconnect the signal cable and the power cable  
from the hard disk drive.  
46 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Press the release button 1 to release the hard disk drive cage and then lift the hard disk drive cage  
out of the chassis.  
Figure 21. Removing the secondary hard disk drive  
6. Pull on the blue handle to release and remove the hard disk drive from the hard disk drive cage.  
7. Flex the sides of the blue bracket to remove the hard disk drive from the bracket.  
8. To install the secondary hard disk drive, flex the sides of the bracket properly and align pin 1 , pin 2 , pin  
3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit  
board 5 on the bottom of the hard disk drive.  
Note: If you are installing a 2.5-inch hard disk drive, install the hard disk drive into a 2.5-inch to 3.5-inch  
hard disk drive tray first and then install the tray into the blue bracket.  
Figure 22. Installing the hard disk drive into the bracket  
Chapter 5. Replacing FRUs 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Slide the new hard disk drive with the blue bracket into the secondary hard disk drive cage until  
it snaps into position.  
10. Slide the hard disk drive cage with the new hard disk drive into the chassis until it is directly underneath  
the metal tab 1 .  
Figure 23. Installing the secondary hard disk drive  
48 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11. Press the hard disk drive cage downward until it snaps into position. Make sure that the hard disk  
drive cage is secured in the chassis.  
Figure 24. Installing the secondary hard disk drive  
12. Connect one end of the signal cable to the hard disk drive and the other end to an available SATA  
connector on the system board. See “Locating parts on the system board” on page 26. Then, locate an  
available five-wire power connector and connect it to the hard disk drive.  
Figure 25. Connecting a SATA hard disk drive  
Installing, removing, or replacing hardware devices  
This section provides instructions on how to install, remove, or replace hardware devices for your server.  
You can maintain your server by replacing the failing hardware devices. If you are replacing a hardware  
device, perform the removal procedure and then perform the installation procedure for the hardware device  
that you want to replace.  
Chapter 5. Replacing FRUs 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Replacing the power supply assembly  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to replace the power supply assembly.  
Although there are no moving parts in your server after the power cord has been disconnected, the following  
warnings are required for your safety and proper Underwriters Laboratories (UL) certification.  
DANGER  
Hazardous moving parts. Keep fingers and other body parts away.  
CAUTION:  
Never remove the cover on a power supply or any part that has the following label attached.  
Hazardous voltage, current, and energy levels are present inside any component that has this label  
attached. There are no serviceable parts inside these components. If you suspect a problem with  
one of these parts, contact a service technician.  
To replace the power supply assembly, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. Lay the server on its side and disconnect the power supply assembly cables from the system board and  
all drives. See “Locating parts on the system board” on page 26.  
50 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Remove the four screws at the rear of the chassis that secure the power supply assembly.  
Figure 26. Removing the screws that secure the power supply assembly  
5. Slide the power supply assembly a little bit forward and then remove it from the chassis.  
Figure 27. Removing the power supply assembly  
6. Ensure that the new power supply assembly is the correct replacement.  
7. Install the new power supply assembly into the chassis so that the screw holes in the power supply  
assembly align with those in the chassis.  
8. Install and tighten the four screws to secure the power supply assembly.  
Note: Use only screws provided by Lenovo.  
9. Reconnect the power supply assembly cables to the system board and each of the drives.  
10. Secure the power supply assembly cables with the cable clips and ties in the chassis.  
Chapter 5. Replacing FRUs 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
What to do next:  
• To work with another piece of hardware, go to the appropriate section.  
• To complete the replacement, go to “Completing the parts replacement” on page 66.  
Replacing the heat sink and fan assembly  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to replace the heat sink and fan assembly.  
CAUTION:  
Turn off the server and wait three to five minutes to let the server cool before removing the server  
cover.  
To replace the heat sink and fan assembly, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. Lay the server on its side for easier access to the system board.  
4. Locate the heat sink and fan assembly. See “Locating parts on the system board” on page 26.  
5. Disconnect the heat sink and fan assembly cable from the microprocessor fan connector on the system  
board. See “Locating parts on the system board” on page 26.  
52 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
6. Follow this sequence to remove the four screws that secure the heat sink and fan assembly to the  
system board:  
a. Partially remove screw 1 , then fully remove screw 2 , and then fully remove screw 1 .  
b. Partially remove screw 3 , then fully remove screw 4 , and then fully remove screw 3 .  
Note: Carefully remove the four screws from the system board to avoid any possible damage to the  
system board. The four screws cannot be removed from the heat sink and fan assembly.  
Figure 28. Removing the heat sink and fan assembly  
7. Lift the failing heat sink and fan assembly off the system board.  
Notes:  
a. You might have to gently twist the heat sink and fan assembly to free it from the microprocessor.  
b. While handling the heat sink and fan assembly, do not touch the thermal grease on the bottom of it.  
8. Place the new heat sink and fan assembly on the system board so that the four screws on the heat sink  
and fan assembly are aligned with the corresponding holes on the system board. Make sure that you  
properly place the heat sink and fan assembly so that you can easily connect the heat sink and fan  
assembly cable to the microprocessor fan connector on the system board.  
9. Follow this sequence to install the four screws to secure the new heat sink and fan assembly. See Figure  
28 “Removing the heat sink and fan assembly” on page 53.  
a. Partially tighten screw 1 , then fully tighten screw 2 , and then fully tighten screw 1 .  
b. Partially tighten screw 3 , then fully tighten screw 4 , and then fully tighten screw 3 .  
Note: Do not over-tighten the screws.  
10. Connect the heat sink and fan assembly cable to the microprocessor fan connector on the system  
board. See “Locating parts on the system board” on page 26.  
What to do next:  
• To work with another piece of hardware, go to the appropriate section.  
Chapter 5. Replacing FRUs 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
• To complete the replacement, go to “Completing the parts replacement” on page 66.  
Replacing the front audio and USB assembly  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to replace the front audio and USB assembly.  
To replace the front audio and USB assembly, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 34.  
4. Disconnect the front audio and USB assembly cable from the system board. See “Locating parts on the  
system board” on page 26.  
5. Note the front audio and USB assembly cable routing and remove the screw that secures the front audio  
and USB assembly. Then, remove the front audio and USB assembly from the chassis.  
Figure 29. Removing the front audio and USB assembly  
6. Route the new front audio and USB assembly through the hole in the chassis.  
7. Position the new front audio and USB assembly to the chassis so that the screw hole in the new front  
audio and USB assembly is aligned with the corresponding hole in the chassis.  
8. Install the screw to secure the new front audio and USB assembly in place.  
9. Connect the new front audio and USB assembly cables to the system board. See “Locating parts on the  
system board” on page 26.  
54 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
10. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 34.  
What to do next:  
• To work with another piece of hardware, go to the appropriate section.  
• To complete the replacement, go to “Completing the parts replacement” on page 66.  
Replacing the front fan assembly  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
Depending on the model type, your server might have a front fan assembly installed. This section provides  
instructions on how to replace the front fan assembly.  
To replace the front fan assembly, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 34.  
4. Disconnect the front fan assembly cable from the power fan connector on the system board. See  
“Locating parts on the system board” on page 26.  
Note: If your server has a secondary hard disk drive installed, remove the secondary hard disk drive  
to get easier access to the power fan connector on the system board. See “Installing or replacing the  
secondary hard disk drive” on page 46.  
Chapter 5. Replacing FRUs 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5. Release the two tabs 1 that attach the front fan assembly to the chassis as shown and then completely  
remove the front fan assembly from the chassis.  
Figure 30. Removing the front fan assembly  
56 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Insert the two tabs 2 of the new front fan assembly into the corresponding holes in the chassis, and  
press the other two tabs 1 through the holes until the front fan assembly is secured in place.  
Figure 31. Installing the front fan assembly  
7. Connect the new front fan assembly cable to the power fan connector on the system board. See  
“Locating parts on the system board” on page 26.  
What to do next:  
• To work with another piece of hardware, go to the appropriate section.  
• To complete the replacement, go to “Completing the parts replacement” on page 66.  
Replacing the rear fan assembly  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to replace the rear fan assembly.  
To replace the rear fan assembly, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
Chapter 5. Replacing FRUs 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. Locate the rear fan assembly. See “Internal components” on page 27.  
4. Disconnect the rear fan assembly cable from the system fan connector on the system board. See  
“Locating parts on the system board” on page 26.  
5. The rear fan assembly is attached to the chassis by four rubber mounts. Remove the rear fan assembly  
by cutting the rubber mounts and gently pulling the rear fan assembly out of the chassis.  
Figure 32. Removing the rear fan assembly  
6. Install the new rear fan assembly by aligning the new rubber mounts with the corresponding holes in the  
chassis and push the rubber mounts through the holes.  
Note: The new rear fan assembly will have four new rubber mounts attached.  
58 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Carefully pull on the tips of the rubber mounts until the new rear fan assembly is secured in place.  
Figure 33. Installing the rear fan assembly  
8. Connect the new rear fan assembly cable to the system fan connector on the system board. See  
“Locating parts on the system board” on page 26.  
What to do next:  
• To work with another piece of hardware, go to the appropriate section.  
• To complete the replacement, go to “Completing the parts replacement” on page 66.  
Replacing the microprocessor  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to replace the microprocessor.  
CAUTION:  
The heat sink and microprocessor might be very hot. Turn off the computer and wait three to five  
minutes to let the computer cool before removing the computer cover.  
Chapter 5. Replacing FRUs 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
To replace the microprocessor, do the following:  
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect  
all power cords from electrical outlets and disconnect all cables that are connected to the computer.  
2. Remove the computer cover. See “Removing the server cover” on page 33.  
3. Lay the computer on its side for easier access to the system board.  
4. Locate the system board and disconnect all cables connected to the system board. See “Locating  
parts on the system board” on page 26.  
5. Remove the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 52.  
Note: Place the heat sink and fan assembly on its side so that the thermal grease on the bottom of it  
does not get in contact with anything.  
6. Lift the small handle 1 and open the retainer 2 to access the microprocessor 3 .  
Figure 34. Accessing the microprocessor  
7. Lift the microprocessor straight up and out of the microprocessor socket.  
Figure 35. Removing the microprocessor  
60 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes:  
a. Your microprocessor and socket might look different from the one illustrated.  
b. Note the orientation of the microprocessor in the socket. You can either look for the small triangle 1  
on one corner of the microprocessor or note the orientation of the notches 2 on the microprocessor.  
This is important when installing the new microprocessor on the system board.  
c. Touch only the edges of the microprocessor. Do not touch the gold contacts on the bottom.  
d. Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be  
kept as clean as possible.  
8. Make sure that the small handle is in the raised position and the microprocessor retainer is fully open.  
9. Remove the protective cover that protects the gold contacts of the new microprocessor.  
10. Hold the new microprocessor by its sides and align the small triangle on one corner of the new  
microprocessor with the corresponding small triangle on one corner of the microprocessor socket.  
11. Lower the new microprocessor straight down into the microprocessor socket on the system board.  
Figure 36. Installing the microprocessor  
12. Close the microprocessor retainer and lock it into position with the small handle to secure the new  
microprocessor in the socket.  
13. Reinstall the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 52.  
Chapter 5. Replacing FRUs 61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14. Reconnect all cables that were disconnected from the system board.  
What to do next:  
• To work with another piece of hardware, go to the appropriate section.  
• To complete the replacement, go to “Completing the parts replacement” on page 66.  
Replacing the system board battery  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to replace the system board battery.  
Your server has a special type of memory that maintains the date, time, and configuration information for  
built-in features. The system board battery keeps this information active when you turn off the server.  
The system board battery normally requires no charging or maintenance throughout its life; however, no  
battery lasts forever. If the system board battery fails, the date, time, and configuration information, including  
passwords, are lost. An error message is displayed when you turn on the server.  
Be sure to consider the following information when you replace the battery in the server:  
• You must replace the battery with a lithium battery of the same type from the same manufacturer.  
• To avoid possible danger, be sure to read and understand the following safety statement.  
• After you replace the system board battery, you must reset passwords, system date and time, and  
reconfigure the server.  
Statement 2  
CAUTION:  
When replacing the lithium battery, use only the battery recommended by the manufacturer. If your  
system has a module containing a lithium battery, replace it only with the same module type made by  
the same manufacturer. The battery contains lithium and can explode if not properly used, handled,  
or disposed of.  
Do not:  
• Throw or immerse into water  
• Heat to more than 100°C (212°F)  
• Repair or disassemble  
Dispose of the battery as required by local ordinances or regulations.  
To replace the system board battery, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. Locate the system board battery. See “Locating parts on the system board” on page 26.  
62 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Remove the old system board battery.  
Figure 37. Removing the old system board battery  
5. Install the new system board battery.  
Figure 38. Installing the new system board battery  
6. Reinstall the computer cover and connect the cables. See “Completing the parts replacement” on  
page 66.  
Note: When the computer is turned on for the first time after the battery is replaced, an error message  
might be displayed. This is normal after replacing the battery.  
7. Turn on the computer and all attached devices.  
8. Use the Setup Utility program to set the date, time, and any passwords. See Chapter 7 “Configuring  
the server” on page 83.  
9. Dispose of the failing battery as required by local ordinances or regulations.  
What to do next:  
• To work with another piece of hardware, go to the appropriate section.  
• To complete the replacement, go to “Completing the parts replacement” on page 66.  
Replacing the system board  
Attention:  
Do not open your server or attempt any repair before reading and understanding the Safety Information and the  
Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page  
29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
This section provides instructions on how to replace the system board.  
CAUTION:  
The heat sink and microprocessor might be very hot. Turn off the computer and wait three to five  
minutes to let the computer cool before removing the computer cover.  
Chapter 5. Replacing FRUs 63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Note: Before replacing the system board, make sure you have a retention module for the new system board.  
To replace the system board, do the following:  
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect  
all power cords from electrical outlets and disconnect all cables that are connected to the computer.  
2. Remove the computer cover. See “Removing the server cover” on page 33.  
3. Place the computer on its side to gain easier access to the system board.  
4. Remove all memory modules and PCI cards that are currently installed. See “Installing or removing a  
memory module” on page 39 and “Installing or replacing a PCI card” on page 35.  
5. Remove the heat sink and fan assembly from the failing system board. See “Replacing the heat sink and  
fan assembly” on page 52.  
6. Remove the microprocessor from the failing system board. See “Replacing the microprocessor” on  
page 59.  
7. Remove the battery from the failing system board. See “Replacing the system board battery” on page 62.  
8. Remove the front fan assembly from the computer. See “Replacing the front fan assembly” on page 55.  
9. Note the location of all cable connections on the system board and disconnect all cables. See “Locating  
parts on the system board” on page 26.  
10. Remove the eight screws that secure the system board to the chassis by following the sequence shown  
in the following illustration.  
11. Carefully lift the failing system board out of the chassis.  
12. Position the new system board into the chassis so that the screw holes in the new system board are  
aligned with those in the chassis. Install the eight screws that secure the system board to the chassis in  
the reverse order that they were removed; that is, install the screw 8 first and install the screw 1 last.  
13. Remove the microprocessor socket cover from the new system board.  
14. Install the memory modules, PCI cards, battery, microprocessor, and heat sink and fan assembly that  
you removed from the failing system board to the new system board.  
15. Connect all cables to the system board. See “Locating parts on the system board” on page 26.  
64 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16. Go to “Completing the parts replacement” on page 66.  
The failing system board must be returned with microprocessor socket covers to protect the pins during  
shipping and handling. Install the microprocessor socket covers removed from the new system board  
on the failing system board.  
Note: The microprocessor socket cover installation procedure should be performed on both microprocessor  
sockets on the failing system board.  
To install a microprocessor socket cover, do the following:  
1. Release the lever securing the microprocessor retainer and open the retainer to access the  
microprocessor.  
2. Grasp the microprocessor on the sides and lift it straight up and out of the socket. Do not touch the  
contacts on the microprocessor socket.  
3. Align the notches 1 of the microprocessor socket cover with the alignment keys 2 of the microprocessor  
socket. Lower the socket cover straight down into the microprocessor socket on the system board.  
Note: Your microprocessor socket and cover might look slightly different from the illustration.  
4. Carefully press the socket cover straight down until it is secured in the socket.  
5. Lower the microprocessor retainer and then lower the lever to secure the retainer. Make sure the  
lever is securely locked into position.  
Chapter 5. Replacing FRUs 65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Completing the parts replacement  
After completing the installation or replacement for all parts, you need to reinstall the server cover and  
reconnect cables.  
To reinstall the server cover and reconnect cables to your server, do the following:  
1. Make sure that all components have been reassembled correctly and that no tools or loose screws are  
left inside your server. See “Internal components” on page 27 for the locations of various components in  
your server.  
2. If you have removed the front bezel, reinstall it. See “Removing and reinstalling the front bezel” on  
page 34.  
3. Make sure that the cables are routed correctly before reinstalling the server cover. Keep cables clear of  
the hinges and sides of the server chassis to avoid interference with reinstalling the server cover.  
4. Position the server cover on the chassis so that the rail guides on the bottom of the server cover engage  
the rails on the chassis. Then, slide the cover to the front of the server until it snaps into position.  
Figure 39. Reinstalling the server cover  
5. Install the screws to secure the server cover.  
6. Lock the server cover if you have a server cover lock.  
7. Reconnect the external cables and power cords to the server. See “Front view” on page 23 and “Rear  
view” on page 24.  
8. Depending on the parts you installed or replaced, you might need to confirm the updated information in  
the Setup Utility program. Refer to Chapter 7 “Configuring the server” on page 83.  
Note: In most areas of the world, Lenovo requires the return of the defective Customer Replaceable Unit  
(CRU). Information about this will come with the CRU or will come a few days after the CRU arrives.  
66 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Connecting the cables  
Attention: To prevent damage to equipment, connect the power cords after completing the parts  
replacement.  
If the server cables and connector panel have color-coded connections, match the color of the cable  
end with the color of the connector. For example, match a blue cable end with a blue panel connector, a  
red cable end with a red connector, and so on. See “Rear view” on page 24 for an illustration of the I/O  
connectors on the rear of the server.  
Turning on the server  
When the server is connected to an ac power source but is not turned on, the operating system does not  
run, and all core logic except for the service processor (the integrated management module) is shut down;  
however, the server can respond to requests to the service processor, such as a remote request to turn on  
the server.  
After the server is connected to an ac power source, you can turn on the server by pressing the power button.  
Turning off the server  
When you turn off the server and leave it connected to ac power, the server can respond to requests to  
the service processor, such as a remote request to turn on the server. While the server remains connected  
to ac power, one or more fans might continue to run. To remove all power from the server, you must  
disconnect it from the power source.  
Some operating systems require an orderly shutdown before you turn off the server. See your  
operating-system documentation for information about shutting down the operating system.  
Statement 5  
CAUTION:  
The power control button on the device and the power switch on the power supply do not turn off  
the electrical current supplied to the device. The device also might have more than one power  
cord. To remove all electrical current from the device, ensure that all power cords are disconnected  
from the power source.  
2
1
The server can be turned off in any of the following ways:  
• You can turn off the server from the operating system, if your operating system supports this feature. After  
an orderly shutdown of the operating system, the server will turn off automatically.  
• You can press the power button to start an orderly shutdown of the operating system and turn off the  
server, if your operating system supports this feature.  
• If the operating system stops functioning, you can press and hold the power button for more than four  
seconds to turn off the server.  
• The server can be turned off by the Shutdown on LAN feature.  
Chapter 5. Replacing FRUs 67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
• The integrated management module (IMM) can turn off the server as an automatic response to a critical  
system failure.  
Connecting external devices  
If you install a supported optional adapter, you can attach external devices to the server.  
To attach an external device, do the following:  
Note: If you are attaching an external device, see the documentation that comes with the device for  
information about cabling.  
1. Read and understand the Safety Information on the ThinkServer Documentation DVD that comes with  
your product, and “Guidelines” on page 29. To obtain a copy of the publications, go to:  
http://www.lenovo.com/support  
2. Turn off the server and all attached devices.  
3. Follow the instructions that come with the device to prepare it for installation and to connect it to  
the server.  
Updating the server configuration  
When you start the server for the first time after you install or remove an internal option or external device,  
you might receive a message saying that the configuration has changed. The Setup Utility program starts  
automatically so that you can save the new configuration settings.  
Some options have device drivers that you must install. For information about installing device drivers, see  
the documentation that comes with each option.  
You can obtain device drivers for operating systems that are not preinstalled at  
http://www.lenovo.com/support. Installation instructions are provided in readme files with the device  
driver files.  
68 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Chapter 6. Parts listing  
The chapter lists the replaceable components for the ThinkServer TS130 machine types 1098, 1100, 1105,  
and 1106.  
To check for an updated parts listing on the Web, do the following:  
1. Go to http://www.lenovo.com/support.  
2. Click Download & Drivers ➙ ThinkServer and then follow the instructions on the Web page to  
download firmware updates for your server.  
Replaceable server components  
Replaceable components are of three types:  
• Self-service customer replaceable unit (CRU): Replacement of self-service CRUs is your responsibility.  
If Lenovo installs a self-service CRU at your request, you will be charged for the installation.  
• Optional-service customer replaceable unit: You may install an optional-service CRU yourself or  
request Lenovo to install it, at no additional charge, under the type of warranty service that is designated  
for your server.  
• Field replaceable unit (FRU): FRUs must be installed only by trained service technicians.  
For information about the terms of the warranty and getting service and assistance, see the Warranty and  
Support Information document.  
The following table lists the part numbers for the server components.  
© Copyright Lenovo 2011  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Table 4. Parts listing, type 1098  
Item  
#
1098 FRUs  
FRU#  
CRU  
1
03X3844  
1
Thermal kit 95 and 73 W (including heatsink, RM and mounting plate) (models CTO all  
models)  
2
2
2
2
2
03T7050  
03T7051  
03T7052  
03T7053  
03T8011  
N
N
N
N
N
Microprocessor, E3-1275 quad core / 2 GT 3.40 GHz 95 W (models CTO)  
Microprocessor, E3-1245 quad core / 2 GT 3.30 GHz 95 W (models CTO)  
Microprocessor, E3-1235 quad core / 2 GT 3.20 GHz 95 W (models CTO)  
Microprocessor, E3-1225 quad core / 2 GT 3.10 GHz 95 W (models CTO)  
Microprocessor, Core i3-2100 dual core / 1 GT 3.1 GHz 65 W (models CTO 12U 12F  
12M 12J 12S 12L 12D 12Y)  
2
3
03T8010  
03X3660  
N
1
Microprocessor, Core i3-2120 dual core / 1 GT 3.3 GHz 65 W (models CTO)  
Memory modules, DDR3 ECC PC3-10600 2 GB UDIMM (1333) (models CTO 12U  
12F 12M 12J 12S 12L 12D 12Y)  
3
4
03X3661  
71Y5543  
1
1
Memory modules, DDR3 ECC PC3-10600 4 GB UDIMM (1333) (models CTO)  
Optical drive, DVD-ROM Drive, 16x/48x (SATA) (models CTO 12U 12F 12M 12J 12S  
12L 12D 12Y)  
4
6
9
7
71Y5545  
43N9599  
03X3845  
03X3764  
1
1
1
1
Optical drive, DVD Burner/CD, RW Rambo 8 (SATA) (models CTO)  
4-pin front fan (models CTO all models)  
4-pin system fan with fan grill (models CTO all models)  
Hard disk drive, non-hot-swap 250 GB SATA Enterprise 7200 rpm, 3 GB/s, XX MB  
cache, 3.5" drive assembly (models CTO 12U 12F 12M 12J 12S 12L 12D 12Y)  
7
7
03X3765  
03X3767  
03X3768  
03T8003  
03X3754  
45J9431  
1
1
Hard disk drive, non-hot-swap 500 GB SATA, Enterprise 7200 rpm, 3 GB/s, XX MB  
cache, 3.5" drive assembly (models CTO)  
Hard disk drive, non-hot-swap 1 TB SATA, Enterprise 7200 rpm, 3 GB/s, XX MB cache,  
3.5" drive assembly (models CTO)  
7
1
Hard disk drive, non-hot-swap 2 TB SATA, Enterprise 7200 rpm, 3 GB/s, XX MB cache,  
3.5" drive assembly (models CTO)  
8
N
N
2
System board, motherboard CPA-SX31200 V1.0, TPM enabled (models CTO 12U  
12F 12M 12J 12S 12L 12D 12Y)  
8
System board, motherboard CPA-SX31200 V1.0, TPM disabled, surge protetion,  
(models CTO 12U 12F 12M 12J 12S 12L 12D 12Y)  
10  
Power supply, 280 Watt (80 plus bronze) (models CTO 12U 12F 12M 12J 12S 12L  
12D 12Y)  
41N8080  
43N9846  
30X3755  
41R6106  
41R3328  
03X3759  
54Y9929  
03X3696  
67Y1430  
03T8152  
2
2
2
2
1
1
1
1
1
1
EMC shield 5.25 (models CTO all models)  
Rear IO shield, ATX, Q57, FOF, print with 6 USB (models CTO all models)  
Optical drive blank bezel (models CTO all models)  
New optional hard disk drive bracket assembly (models CTO all models)  
Cable, SATA 120 mm (RoHS) (models CTO all models)  
Cable PATA 1-2 for RDX (models CTO all models)  
Cable, SATA 250 mm, 1 latching for device (RoHS) (models CTO all models)  
Optical drive, 15 u 750 mm single SATA cable V1.0 (models CTO)  
Intel Pro/1000 PT Dual Port Ethernet card (models CTO)  
NVIDIA graphics card, NVS300, 512 MB, DMS59 (models CTO)  
70 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 4. Parts listing, type 1098 (continued)  
Item  
#
1098 FRUs  
FRU#  
CRU  
03X3841  
43N9091  
42Y8181  
41X6298  
45J9495  
03X3662  
03X3663  
03X3664  
1
1
1
1
1
1
1
1
Hard disk drive cage assembly (models CTO all models)  
Internal speaker assembly, 400mm (models CTO all models)  
Cable, DMS59 (M) - 2 VGA (F), 203 mm (models CTO)  
Cable, DMS59 (M) - 2 DVI (F), 203mm (CTO)  
Temp sense cable (6pin 460 mm) (models CTO all models)  
Lenovo RDX 160 GB internal USB drive (models CTO)  
Lenovo RDX 320 GB internal USB drive (models CTO)  
Lenovo RDX 500 GB internal USB drive (models CTO)  
Table 5. Parts listing, type 1100  
Item  
#
1100 FRUs  
FRU#  
CRU  
1
03X3844  
1
Thermal kit 95 and 73 W (including heatsink, RM and mounting plate) (models CTO all  
models)  
2
2
2
2
03T7050  
03T7051  
03T7052  
03T7053  
N
N
N
N
Microprocessor, E3-1275 quad core / 2 GT 3.40 GHz 95 W (models CTO)  
Microprocessor, E3-1245 quad core / 2 GT 3.30 GHz 95 W (models CTO)  
Microprocessor, E3-1235 quad core / 2 GT 3.20 GHz 95 W (models CTO)  
Microprocessor, E3-1225 quad core / 2 GT 3.10 GHz 95 W (models CTO 12U 12F  
12G 12M 12J 12S 12L 12D 12Y)  
2
2
3
03T8011  
03T8010  
03X3660  
N
N
1
Microprocessor, Core i3-2100 dual core / 1 GT 3.1 GHz 65 W (models CTO)  
Microprocessor, Core i3-2120 dual core / 1 GT 3.3 GHz 65 W (models CTO)  
Memory modules, DDR3 ECC PC3-10600 2 GB UDIMM (1333) (models CTO 12U 12F  
12G 12M 12J 12S 12L 12D 12Y)  
3
4
03X3661  
71Y5543  
1
1
Memory modules, DDR3 ECC PC3-10600 4 GB UDIMM (1333) (models CTO)  
Optical drive, DVD-ROM drive, 16x/48x (SATA) (models CTO 12U 12F 12G 12M 12J  
12S 12L 12D 12Y)  
4
6
9
7
71Y5545  
43N9599  
03X3845  
03X3764  
1
1
1
1
Optical drive, DVD Burner/CD, RW Rambo 8 (SATA) (models CTO)  
4-pin front fan (models CTO all models)  
4-pin system fan with fan grill (models CTO all models)  
Hard disk drive, non-hot-swap 250 GB SATA Enterprise 7200 rpm, 3 GB/s, XXMB  
cache, 3.5" drive assembly (models CTO 12U 12F 12G 12M 12J 12S 12L 12D 12Y)  
7
7
7
8
8
03X3765  
03X3767  
03X3768  
03T8003  
03X3754  
1
1
Hard disk drive, non-hot-swap 500 GB SATA, Enterprise 7200 rpm, 3 GB/s, XXMB  
cache, 3.5" drive assembly (models CTO)  
Hard disk drive, non-hot-swap 1 TB SATA, Enterprise 7200 rpm, 3 GB/s, XXMB cache,  
3.5" drive assembly (models CTO)  
1
Hard disk drive, non-hot-swap 2 TB SATA, Enterprise 7200 rpm, 3 GB/s, XXMB cache,  
3.5" drive assembly (models CTO)  
N
N
System board, motherboard CPA-SX31200 V1.0, TPM enabled (models CTO 12U  
12F 12M 12J 12S 12L 12D 12Y)  
System board, motherboard CPA-SX31200 V1.0, TPM disabled, surge protetion  
(models CTO 12U 12F 12G 12M 12J 12S 12L 12D 12Y)  
Chapter 6. Parts listing 71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 5. Parts listing, type 1100 (continued)  
Item  
#
1100 FRUs  
FRU#  
CRU  
10  
45J9431  
2
Power supply, 280 Watt (80 plus bronze) (models CTO 12U 12F 12G 12M 12J 12S  
12L 12D 12Y)  
41N8080  
43N9846  
30X3755  
41R6106  
41R3328  
03X3759  
54Y9929  
03X3696  
43N9091  
67Y1430  
03T8152  
03X3841  
42Y8181  
41X6298  
45J9495  
03X3662  
03X3663  
03X3664  
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
EMC shield 5.25 (models CTO all models)  
Rear IO shield, ATX, Q57, FOF, print with 6 USB (models CTO all models)  
Optical drive blank bezel (models CTO all models)  
New optional hard disk drive bracket assembly (models CTO all models)  
Cable, SATA 120 mm (RoHS) (models CTO all models)  
Cable PATA 1-2 for RDX (models CTO all models)  
Cable, SATA 250 mm, 1 latching for device (RoHS) (models CTO all models)  
Optical drive, 15 u 750 mm single SATA cable V1.0 (models CTO all models)  
Internal speaker assembly, 400 mm (models CTO all models)  
Intel Pro/1000 PT dual port Ethernet card (models CTO)  
NVIDIA graphics card, NVS300, 512 MB, DMS59 (models CTO)  
Hard disk drive cage assembly (models CTO all models)  
Cable, DMS59 (M) - 2 VGA (F), 203 mm (models CTO)  
Cable, DMS59 (M) - 2 DVI (F), 203 mm (models CTO)  
Temp sense cable (6pin 460 mm) (models CTO all models)  
Lenovo RDX 160 GB internal USB drive (models CTO)  
Lenovo RDX 320 GB internal USB drive (models CTO)  
Lenovo RDX 500 GB internal USB drive (models CTO)  
Table 6. Parts listing, type 1105  
Item  
#
1105 FRUs  
FRU#  
CRU  
1
2
2
2
2
03X3844  
1
Thermal kit 95 and 73 W (including heatsink, RM and mounting plate) (models CTO all  
models)  
03T7050  
03T7051  
03T7052  
03T7053  
N
N
N
N
Microprocessor, E3-1275 quad core / 2 GT 3.40 GHz 95 W (models CTO 1BU 1BF  
1BM 1BJ 1BS 1BL 1BD 1BY)  
Microprocessor, E3-1245 quad core / 2 GT 3.30 GHz 95 W (models CTO 1EU 1EF 1EM  
1EJ 1ES 1EL 1ED 1EY)  
Microprocessor, E3-1235 quad core / 2 GT 3.20 GHz 95 W (modles CTO 1AU 1AF 1AM  
1AJ 1AS 1AL 1AD 1AY 1DU 1DF 1DM 1DJ 1DS 1DL 1DD 1DY )  
Microprocessor, E3-1225 quad core / 2 GT 3.10 GHz 95 W (models CTO 18F 18M  
18J 18S 18L 18D 18Y 19U 19F 19M 19J 19S 19L 19D 19Y 1CU 1CF 1CM 1CJ 1CS  
1CL 1CD 1CY )  
2
03T8011  
N
Microprocessor, Core i3-2100 dual core / 1 GT 3.1 GHz 65 W (models CTO 15U 15F  
15M 15J 15S 15L 15D 15Y 11G)  
2
3
03T8010  
03X3660  
N
1
Microprocessor, Core i3-2120 dual core / 1 GT 3.3 GHz 65 W (models CTO 16J)  
Memory modules, DDR3 ECC PC3-10600 2 GB UDIMM (1333) (models CTO 15U 15F  
15M 15J 15S 15L 15D 15Y 16J 18U 18F 18M 18J 18S 18L 18D 18Y 19U 19F 19M  
19J 19S 19L 19D 19Y 11G A1G)  
72 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 6. Parts listing, type 1105 (continued)  
Item  
#
1105 FRUs  
FRU#  
CRU  
3
03X3661  
1
Memory modules, DDR3 ECC PC3-10600 4 GB UDIMM (1333) (models CTO 1AU  
1AF 1AM 1AJ 1AS 1AL 1AD 1AY 1BU 1BF 1BM 1BJ 1BS 1BL 1BD 1BY 1CU 1CF  
1CM 1CJ 1CS 1CL 1CD 1CY 1DU 1DF 1DM 1DJ 1DS 1DL 1DD 1DY 1EU 1EF 1EM  
1EJ 1ES 1EL 1ED 1EY )  
4
71Y5543  
1
Optical drive, DVD-ROM drive, 16x/48x (SATA) (models CTO 15U 15F 15M 15J 15S  
15L 15D 15Y 16J 18U 18F 18M 18J 18S 18L 18D 18Y 19U 19F 19M 19J 19S 19L  
19D 19Y 11G A1G)  
4
6
9
7
71Y5545  
43N9599  
03X3845  
03X3764  
1
1
1
1
Optical drive, DVD Burner/CD, RW Rambo 8 (SATA) (models CTO)  
4-pin front fan (models CTO all models)  
4-pin system fan with fan grill (models CTO all models)  
Hard disk drive, non-hot-swap 250 GB SATA Enterprise 7200 rpm, 3 GB/s, XX MB  
cache, 3.5" drive assembly (CTO 15U 15F 15M 15J 15S 15L 15D 15Y 16J 18U 18F  
18M 18J 18S 18L 18D 18Y 19U 19F 19M 19J 19S 19L 19D 19Y 1BU 1BF 1BM 1BJ  
1BS 1BL 1BD 1BY 1DU 1DF 1DM 1DJ DS 1DL 1DD 1DY 11G A1G)  
7
03X3765  
1
Hard disk drive, non-hot-swap 500 GB SATA, Enterprise 7200 rpm, 3 GB/s, XX MB  
cache, 3.5" drive assembly (models CTO 1AU 1AF 1AG 1AM 1AJ 1AS 1AL 1AD 1AY  
1CU 1CF 1CS 1CL 1CD 1CY 1CM 1CJ 1EU 1EF 1EM 1EJ 1ES 1EL 1ED 1EY)  
7
7
8
03X3767  
03X3768  
03T8003  
1
1
Hard disk drive, non-hot-swap 1 TB SATA, Enterprise 7200 rpm, 3 GB/s, XX MB cache,  
3.5" drive assembly (models CTO)  
Hard disk drive, non-hot-swap 2 TB SATA, Enterprise 7200 rpm, 3 GB/s, XX MB cache,  
3.5" drive assembly (models CTO)  
N
System board, motherboard CPA-SX31200 V1.0, TPM enabled (models CTO 15U 15F  
15M 15J 15S 15L 15D 15Y 16J 18U 18F 18M 18J 18S 18L 18D 18Y 19U 19F 19M  
19J 19S 19L 19D 19Y 1AU 1AF 1AM 1AJ 1AS 1AL 1AD 1AY 1BU 1BF 1BM 1BJ 1BS  
1BL 1BD 1BY 1CU 1CF 1CM 1CJ 1CS 1CL 1CD 1CY 1DU 1DF 1DM 1DJ 1DS 1DL  
1DD 1DY 1EU 1EF 1EM 1EJ 1ES 1EL 1ED 1EY 11G A1G)  
8
03X3754  
45J9431  
N
2
System board, motherboard CPA-SX31200 V1.0, TPM disabled, surge protetion  
(models CTO 15U 15F 15M 15J 15S 15L 15D 15Y 16J 18U 18F 18M 18J 18S 18L 18D  
18Y 19U 19F 19M 19J 19S 19L 19D 19Y 1AU 1AF 1AM 1AJ 1AS 1AL 1AD 1AY 1BU  
1BF 1BM 1BJ 1BS 1BL 1BD 1BY 1CU 1CF 1CM 1CJ 1CS 1CL 1CD 1CY 1DU 1DF  
1DM 1DJ 1DS 1DL 1DD 1DY 1EU 1EF 1EM 1EJ 1ES 1EL 1ED 1EY 11G A1G)  
10  
Power supply, 280 Watt (80 plus bronze) (models CTO 15U 15F 15M 15J 15S 15L 15D  
15Y 16J 18U 18F 18M 18J 18S 18L 18D 18Y 19U 19F 19M 19J 19S 19L 19D 19Y  
1AU 1AF 1AM 1AJ 1AS 1AL 1AD 1AY 1BU 1BF 1BM 1BJ 1BS 1BL 1BD 1BY 1CU  
1CF 1CM 1CJ 1CS 1CL 1CD 1CY 1DU 1DF 1DM 1DJ 1DS 1DL 1DD 1DY 1EU 1EF  
1EM 1EJ 1ES 1EL 1ED 1EY 11G A1G)  
41N8080  
43N9846  
30X3755  
41R6106  
41R3328  
03X3759  
54Y9929  
03X3696  
67Y1430  
2
2
2
2
1
1
1
1
1
EMC shield 5.25 (models CTO all models)  
Rear IO shield, ATX, Q57, FOF, print with 6 USB (models CTO all models)  
Optical drive blank bezel (models CTO all models)  
New optional hard disk drive bracket assembly (models CTO all models)  
Cable, SATA 120 mm (RoHS) (models CTO all models)  
Cable PATA 1-2 for RDX (models CTO all models)  
Cable, SATA 250 mm, 1 latching for device (RoHS) (models CTO all models)  
Optical drive, 15 u 750 mm single SATA cable V1.0 (models CTO)  
Intel Pro/1000 PT dual port Ethernet card (models CTO)  
Chapter 6. Parts listing 73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 6. Parts listing, type 1105 (continued)  
Item  
#
1105 FRUs  
FRU#  
CRU  
03T8152  
03X3841  
43N9091  
42Y8181  
41X6298  
45J9495  
03X3662  
03X3663  
03X3664  
1
1
1
1
1
1
1
1
1
NVIDIA graphics card, NVS300, 512 MB, DMS59 (models CTO)  
Hard disk drive cage assembly (models CTO all models)  
Internal speaker assembly, 400mm (models CTO all models)  
Cable, DMS59 (M) - 2 VGA (F), 203 mm (models CTO)  
Cable, DMS59 (M) - 2 DVI (F), 203 mm (models CTO)  
Temp sense cable (6pin 460 mm) (models CTO all models)  
Lenovo RDX 160 GB internal USB drive (models CTO)  
Lenovo RDX 320 GB internal USB drive (models CTO)  
Lenovo RDX 500 GB internal USB drive (models CTO)  
Table 7. Parts listing, type 1106  
Item  
#
1106 FRUs  
FRU#  
CRU  
1
03X3844  
1
Thermal kit 95 and 73 W (including heatsink, RM and mounting plate) (models CTO all  
models)  
2
2
2
03T7050  
03T7051  
03T7052  
N
N
N
Microprocessor, E3-1275 quad core / 2 GT 3.40 GHz 95 W (models CTO)  
Microprocessor, E3-1245 quad core / 2 GT 3.30 GHz 95 W (models CTO)  
Microprocessor, E3-1235 quad core / 2 GT 3.20 GHz 95 W (modles CTO 1HG A1G  
A1M)  
2
2
2
03T7053  
03T8011  
03T8010  
N
N
N
Microprocessor, E3-1225 quad core / 2 GT 3.10 GHz 95 W (models CTO 1GG)  
Microprocessor, Core i3-2100 dual core / 1 GT 3.1 GHz 65 W (models CTO)  
Microprocessor, Core i3-2120 dual core / 1 GT 3.3 GHz 65 W (models CTO 1EU 1EF  
1EM 1EJ 1ES 1EL 1ED 1EY)  
3
3
03X3660  
03X3661  
1
1
Memory modules, DDR3 ECC PC3-10600 2 GB UDIMM (1333) (models CTO 1EU  
1EF 1EM 1EJ 1ES 1EL 1ED 1EY)  
Memory modules, DDR3 ECC PC3-10600 4 GB UDIMM (1333) (models CTO 1GG  
1HG A1G A1M)  
4
4
71Y5543  
71Y5545  
1
1
Optical drive, DVD-ROM drive, 16x/48x (SATA) (models CTO)  
Optical drive, DVD Burner/CD, RW Rambo 8 (SATA) (models CTO 1GG 1EU 1EF 1EM  
1EJ A1G 1ES 1EL 1ED 1EY A1M)  
6
9
7
43N9599  
03X3845  
03X3764  
1
1
1
4-pin front fan ( CTO models CTO all models)  
4-pin system fan with fan grill (models CTO all models)  
Hard disk drive, non-hot-swap 250 GB SATA Enterprise 7200 rpm, 3 GB/s, XX MB  
cache, 3.5" drive assembly (models CTO 1HG)  
7
03X3765  
1
Hard disk drive, non-hot-swap 500 GB SATA, Enterprise 7200 rpm, 3 GB/s, XX MB  
cache, 3.5" drive assembly (models CTO 1GG 1EU 1EF 1EM 1EJ A1G 1ES 1EL 1ED  
1EY A1M)  
7
7
03X3767  
03X3768  
1
1
Hard disk drive, non-hot-swap 1 TB SATA, Enterprise 7200 rpm, 3 GB/s, XX MB cache,  
3.5" drive assembly (models CTO)  
Hard disk drive, non-hot-swap 2 TB SATA, Enterprise 7200 rpm, 3 GB/s, XX MB cache,  
3.5" drive assembly (models CTO)  
74 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 7. Parts listing, type 1106 (continued)  
Item  
#
1106 FRUs  
FRU#  
CRU  
8
03T8003  
N
System board, motherboard CPA-SX31200 V1.0, TPM enabled (models CTO 1GG 1HG  
1EU 1EF 1EM 1EJ A1G 1ES 1EL 1ED 1EY A1M)  
8
03X3754  
45J9431  
N
2
System board, motherboard CPA-SX31200 V1.0, TPM disabled, surge protetion  
(models CTO 1GG 1HG 1EU 1EF 1EM 1EJ A1G 1ES 1EL 1ED 1EY A1M)  
10  
Power supply, 280 Watt (80 plus bronze) (models CTO 1GG 1HG 1EU 1EF 1EM 1EJ  
A1G 1ES 1EL 1ED 1EY)  
41N8080  
43N9846  
30X3755  
41R6106  
41R3328  
03X3759  
54Y9929  
03X3696  
67Y1430  
03T8152  
03X3841  
43N9091  
42Y8181  
41X6298  
45J9495  
03X3662  
03X3663  
03X3664  
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
EMC shield 5.25 (models CTO all models)  
Rear IO shield, ATX, Q57, FOF, print with 6 USB (models CTO all models)  
Optical drive blank bezel (models CTO all models)  
New optional hard disk drive bracket assembly (models CTO all models)  
Cable, SATA 120 mm (RoHS) (models CTO all models)  
Cable PATA 1-2 for RDX (models CTO all models)  
Cable, SATA 250 mm, 1 latching for device (RoHS) (models CTO all models)  
Optical drive, 15 u 750 mm single SATA cable V1.0 (models CTO)  
Intel Pro/1000 PT dual port Ethernet card (models CTO)  
NVIDIA graphics card, NVS300, 512 MB, DMS59 (models CTO)  
Hard disk drive cage assembly (models CTO all models)  
Internal speaker assembly, 400mm (models CTO all models)  
Cable, DMS59 (M) - 2 VGA (F), 203 mm (models CTO)  
Cable, DMS59 (M) - 2 DVI (F), 203 mm (models CTO)  
Temp sense cable (6pin 460 mm) (models CTO all models)  
Lenovo RDX 160 GB internal USB drive (models CTO)  
Lenovo RDX 320 GB internal USB drive (models CTO)  
Lenovo RDX 500 GB internal USB drive (models CTO)  
Ship group  
A Lenovo ship group for a specific country or region is usually available only in that country or region.  
Table 8. Ship group, type 1098  
1098 Ship group  
EasyStartup DVD (English language version) (models CTO)  
Documentation DVD (models CTO)  
FRU#  
CRU  
03X3653  
03X3654  
03X3655  
90Y1183  
1
1
1
1
EasyStartup DVD (multiple language version) (models CTO)  
Windows Server 2008 R2 64-bit ship group US (models CTO)  
Table 9. Ship group, type 1100  
1100 Ship group  
FRU#  
CRU  
03X3653  
03X3654  
1
1
EasyStartup DVD (English language version) (models CTO)  
Documentation DVD (models CTO)  
Chapter 6. Parts listing 75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Table 9. Ship group, type 1100 (continued)  
1100 Ship group  
FRU#  
CRU  
03X3655  
90Y1183  
1
1
EasyStartup DVD (multiple language version) (models CTO)  
Windows Server 2008 R2 64-bit ship group US (models CTO)  
Table 10. Ship group, type 1105  
1105 Ship group  
FRU#  
CRU  
03X3653  
03X3654  
03X3655  
90Y1183  
1
1
1
1
EasyStartup DVD (English language version) (models CTO)  
Documentation DVD (models CTO)  
EasyStartup DVD (multiple language version) (models CTO)  
Windows Server 2008 R2 64-bit ship group US (models CTO)  
Table 11. Ship group, type 1106  
1106 Ship group  
FRU#  
CRU  
03X3653  
03X3654  
03X3655  
90Y1183  
1
1
1
1
EasyStartup DVD (English language version) (models CTO)  
Documentation DVD (models CTO)  
EasyStartup DVD (multiple language version) (models CTO)  
Windows Server 2008 R2 64-bit ship group US (models CTO)  
Power cords  
For your safety, Lenovo provides a power cord with a grounded attachment plug to use with this Lenovo  
product. To avoid electrical shock, always use the power cord and plug with a properly grounded outlet.  
Lenovo power cords used in the United States and Canada are listed by Underwriter's Laboratories (UL) and  
certified by the Canadian Standards Association (CSA).  
For units intended to be operated at 115 volts: Use a UL-listed and CSA-certified cord set consisting of a  
minimum 18 AWG, Type SVT or SJT, three-conductor cord, a maximum of 15 feet in length and a parallel  
blade, grounding-type attachment plug rated 15 amperes, 125 volts.  
For units intended to be operated at 230 volts (U.S. use): Use a UL-listed and CSA-certified cord set  
consisting of a minimum 18 AWG, Type SVT or SJT, three-conductor cord, a maximum of 15 feet in length  
and a tandem blade, grounding-type attachment plug rated 15 amperes, 250 volts.  
For units intended to be operated at 230 volts (outside the U.S.): Use a cord set with a grounding-type  
attachment plug. The cord set should have the appropriate safety approvals for the country in which the  
equipment will be installed.  
Lenovo power cords for a specific country or region are usually available only in that country or region.  
Table 12. Primary power cords, type 1098  
1098 Primary power cords  
Line cord - US (models CTO 12U 12F 12D 12S 12L)  
FRU#  
CRU  
41R3184  
1
41R3256  
24R2633  
1
1
Line cord - China (models CTO)  
Line cord - Japan (models CTO 12J)  
76 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Table 12. Primary power cords, type 1098 (continued)  
1098 Primary power cords  
FRU#  
CRU  
45J9595  
41R3176  
41R3196  
41R3260  
41R3224  
1
1
1
1
1
Line cord - Brazil (models CTO)  
Line cord - Latin America High Voltage (Argentina, Paraguay, Uraguay) (models CTO 12Y 12L)  
Line cord - Australia/ New Zealand (models CTO 12M)  
Line cord - Korea (models CTO)  
Line cord - Hong Kong, United Kingdom, Singapore, Malaysia, Brunei, Ireland, (models CTO  
11G 12G 18G 19G)  
41R3278  
41R3232  
41R3208  
1
1
1
Line cord - Taiwan (models CTO)  
Line cord - Italy (models CTO 12S 12L 12Y)  
Line-cord - Indonesia, Laos, Cambodia, Vietnam, Austria, Belgium, Croatia, Czechoslovakia,  
Finland, France, Germany, Hungary, Netherlands, Norway, Poland, Portugal, Romania, Spain,  
Sweden (models CTO)  
41R3212  
41R3228  
41R3236  
41R3220  
41R3341  
1
1
1
1
1
Line cord - Denmark (models CTO)  
Line cord - Switzerland (models CTO)  
Line cord - Israel (models CTO)  
Line cord - South Africa (models CTO 12M)  
Line cord - India (models CTO)  
Table 13. Secondary power cords, type 1098  
1098 Secondary power cords  
FRU#  
CRU  
41R3184  
1
Line cord - US (models CTO 12U 12F 12D 12S 12L)  
41R3256  
24R2633  
45J9595  
41R3176  
41R3196  
41R3260  
41R3224  
1
1
1
1
1
1
1
Line cord - China (models CTO)  
Line cord - Japan (models CTO 12J)  
Line cord - Brazil (models CTO)  
Line cord - Latin America High Voltage (Argentina, Paraguay, Uraguay) (models CTO 12Y 12L)  
Line cord - Australia/ New Zealand (models CTO 12M)  
Line cord - Korea (models CTO)  
Line cord - Hong Kong, United Kingdom, Singapore, Malaysia, Brunei, Ireland, (models CTO)  
41R3278  
41R3232  
41R3208  
1
1
1
Line cord - Taiwan (models CTO)  
Line cord - Italy (models CTO 12S 12L 12Y)  
Line-cord - Indonesia, Laos, Cambodia, Vietnam, Austria, Belgium, Croatia, Czechoslovakia,  
Finland, France, Germany, Hungary, Netherlands, Norway, Poland, Portugal, Romania, Spain,  
Sweden (models CTO)  
41R3212  
41R3228  
41R3236  
41R3220  
41R3341  
1
1
1
1
1
Line cord - Denmark (models CTO)  
Line cord - Switzerland (models CTO)  
Line cord - Israel (models CTO)  
Line cord - South Africa (models CTO 12M)  
Line cord - India (models CTO)  
Chapter 6. Parts listing 77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 14. Primary power cords, type 1100  
1100 Primary power cords  
FRU#  
CRU  
41R3184  
1
Line cord - US (models CTO 12U 12F 12D 12S 12L)  
41R3256  
24R2633  
45J9595  
41R3176  
41R3196  
41R3260  
41R3224  
1
1
1
1
1
1
1
Line cord - China (models CTO)  
Line cord - Japan (models CTO 12J)  
Line cord - Brazil (models CTO)  
Line cord - Latin America High Voltage (Argentina, Paraguay, Uraguay) (models CTO 12Y 12L)  
Line cord - Australia/ New Zealand (models CTO 12M)  
Line cord - Korea (models CTO)  
Line cord - Hong Kong, United Kingdom, Singapore, Malaysia, Brunei, Ireland, (models CTO)  
41R3278  
41R3232  
41R3208  
1
1
1
Line cord - Taiwan (models CTO)  
Line cord - Italy (models CTO 12S 12L 12Y)  
Line-cord - Indonesia, Laos, Cambodia, Vietnam, Austria, Belgium, Croatia, Czechoslovakia,  
Finland, France, Germany, Hungary, Netherlands, Norway, Poland, Portugal, Romania, Spain,  
Sweden (models CTO)  
41R3212  
41R3228  
41R3236  
41R3220  
41R3341  
1
1
1
1
1
Line cord - Denmark (models CTO)  
Line cord - Switzerland (models CTO)  
Line cord - Israel (models CTO)  
Line cord - South Africa (models CTO 12M)  
Line cord - India (models CTO)  
Table 15. Secondary power cords, type 1100  
1100 Secondary power cords  
FRU#  
CRU  
41R3184  
1
Line cord - US (models CTO 12U 12F 12D 12S 12L)  
41R3256  
24R2633  
45J9595  
41R3176  
41R3196  
41R3260  
41R3224  
1
1
1
1
1
1
1
Line cord - China (models CTO)  
Line cord - Japan (models CTO 12J)  
Line cord - Brazil (models CTO)  
Line cord - Latin America High Voltage (Argentina, Paraguay, Uraguay) (models CTO 12Y 12L)  
Line cord - Australia/ New Zealand (models CTO 12M)  
Line cord - Korea (models CTO)  
Line cord - Hong Kong, United Kingdom, Singapore, Malaysia, Brunei, Ireland, (models CTO)  
41R3278  
41R3232  
41R3208  
1
1
1
Line cord - Taiwan (models CTO)  
Line cord - Italy (models CTO 12S 12L 12Y)  
Line-cord - Indonesia, Laos, Cambodia, Vietnam, Austria, Belgium, Croatia, Czechoslovakia,  
Finland, France, Germany, Hungary, Netherlands, Norway, Poland, Portugal, Romania, Spain,  
Sweden (models CTO)  
41R3212  
41R3228  
41R3236  
1
1
1
Line cord - Denmark (models CTO)  
Line cord - Switzerland (models CTO)  
Line cord - Israel (models CTO)  
78 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 15. Secondary power cords, type 1100 (continued)  
1100 Secondary power cords  
FRU#  
CRU  
41R3220  
41R3341  
1
1
Line cord - South Africa (models CTO 12M)  
Line cord - India (models CTO)  
Table 16. Primary power cords, type 1105  
1105 Primary power cords  
FRU#  
CRU  
41R3184  
1
Line cord - US (models CTO 15U 15F 18F 19U 19F 1AU 1AF 1BU 1BF 1CU 1CF 1DU 1DF  
1EU 1EF 15D 15S 15L 18D 18S 18L 19D 19S 19L 1AD 1AS 1AL 1BD 1BS 1BL 1CD 1CS  
1CL 1DD 1DS 1DL 1ED 1ES 1EL)  
41R3256  
24R2633  
45J9595  
41R3176  
1
1
1
1
Line cord - China (models CTO)  
Line cord - Japan (models CTO 15J 16J 18J 19J 1AJ 1BJ 1CJ 1DJ 1EJ )  
Line cord - Brazil (models CTO)  
Line cord - Latin America High Voltage (Argentina, Paraguay, Uraguay) (models CTO 15Y 15L  
18Y 18L 19Y 19L 1AY 1AL 1BY 1BL 1CY 1CL 1DY 1DL 1EY 1EL)  
41R3196  
41R3260  
41R3224  
1
1
1
Line cord - Australia/ New Zealand (models CTO 15M 18M 19M 1AM 1BM 1CM 1DM 1EM)  
Line cord - Korea (models CTO)  
Line cord - Hong Kong, United Kingdom, Singapore, Malaysia, Brunei, Ireland, (models CTO  
11G A1G)  
41R3278  
41R3232  
1
1
Line cord - Taiwan (models CTO)  
Line cord - Italy (models CTO 11G A1G 15S 15L 15Y 18S 18L 18Y 19S 19L 19Y 1AS 1AL 1AY  
1BS 1BL 1BY 1CS 1CL 1CY 1DS 1DL 1DY 1ES 1EL 1EY)  
41R3208  
1
Line-cord - Indonesia, Laos, Cambodia, Vietnam, Austria, Belgium, Croatia, Czechoslovakia,  
Finland, France, Germany, Hungary, Netherlands, Norway, Poland, Portugal, Romania, Spain,  
Sweden (models CTO 11G A1G)  
41R3212  
41R3228  
41R3236  
41R3220  
41R3341  
1
1
1
1
1
Line cord - Denmark (models CTO 11G A1G)  
Line cord - Switzerland (models CTO 11G A1G)  
Line cord - Israel (CTO 11G A1G)  
Line cord - South Africa (models CTO 15M 18M 19M 1AM 1BM 1CM 1DM 1EM 11G A1G)  
Line cord - India (models CTO)  
Table 17. Secondary power cords, type 1105  
1105 Secondary power cords  
FRU#  
CRU  
41R3184  
1
Line cord - US (models CTO 15U 15F 18F 19U 19F 1AU 1AF 1BU 1BF 1CU 1CF 1DU 1DF  
1EU 1EF 15D 15S 15L 18D 18S 18L 19D 19S 19L 1AD 1AS 1AL 1BD 1BS 1BL 1CD 1CS  
1CL 1DD 1DS 1DL 1ED 1ES 1EL)  
41R3256  
24R2633  
45J9595  
41R3176  
1
1
1
1
Line cord - China (models CTO)  
Line cord - Japan (models CTO 15J 16J 18J 19J 1AJ 1BJ 1CJ 1DJ 1EJ )  
Line cord - Brazil (models CTO)  
Line cord - Latin America High Voltage (Argentina, Paraguay, Uraguay) (models CTO 15Y 15L  
18Y 18L 19Y 19L 1AY 1AL 1BY 1BL 1CY 1CL 1DY 1DL 1EY 1EL)  
41R3196  
41R3260  
1
1
Line cord - Australia/ New Zealand (models CTO 15M 18M 19M 1AM 1BM 1CM 1DM 1EM)  
Line cord - Korea (models CTO)  
Chapter 6. Parts listing 79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 17. Secondary power cords, type 1105 (continued)  
1105 Secondary power cords  
FRU#  
CRU  
41R3224  
1
Line cord - Hong Kong, United Kingdom, Singapore, Malaysia, Brunei, Ireland, (CTO 11G A1G)  
41R3278  
41R3232  
1
1
Line cord - Taiwan (models CTO)  
Line cord - Italy (models CTO 11G A1G 15S 15L 15Y 18S 18L 18Y 19S 19L 19Y 1AS 1AL 1AY  
1BS 1BL 1BY 1CS 1CL 1CY 1DS 1DL 1DY 1ES 1EL 1EY)  
41R3208  
1
Line-cord - Indonesia, Laos, Cambodia, Vietnam, Austria, Belgium, Croatia, Czechoslovakia,  
Finland, France, Germany, Hungary, Netherlands, Norway, Poland, Portugal, Romania, Spain,  
Sweden (models CTO 11G A1G)  
41R3212  
41R3228  
41R3236  
41R3220  
41R3341  
1
1
1
1
1
Line cord - Denmark (models CTO 11G A1G)  
Line cord - Switzerland (models CTO 11G A1G)  
Line cord - Israel (models CTO 11G A1G)  
Line cord - South Africa (models CTO 15M 18M 19M 1AM 1BM 1CM 1DM 1EM 11G A1G)  
Line cord - India (models CTO)  
Table 18. Primary power cords, type 1106  
1106 Primary power cords  
FRU#  
CRU  
41R3184  
1
Line cord - US (models CTO 1EU 1EF 1ED 1ES 1EL)  
41R3256  
24R2633  
45J9595  
41R3176  
41R3196  
41R3260  
41R3224  
1
1
1
1
1
1
1
Line cord - China (models CTO)  
Line cord - Japan (models CTO 1EJ)  
Line cord - Brazil (models CTO)  
Line cord - Latin America High Voltage (Argentina, Paraguay, Uraguay) (models CTO 1EY 1EL)  
Line cord - Australia/ New Zealand (models CTO 1EM A1M)  
Line cord - Korea (models CTO)  
Line cord - Hong Kong, United Kingdom, Singapore, Malaysia, Brunei, Ireland, (models CTO  
1GG 1HG A1G)  
41R3278  
41R3232  
41R3208  
1
1
1
Line cord - Taiwan (models CTO)  
Line cord - Italy (models CTO 1GG 1HG A1G 1ES 1EL 1EY)  
Line-cord - Indonesia, Laos, Cambodia, Vietnam, Austria, Belgium, Croatia, Czechoslovakia,  
Finland, France, Germany, Hungary, Netherlands, Norway, Poland, Portugal, Romania, Spain,  
Sweden (models CTO)  
41R3212  
41R3228  
41R3236  
41R3220  
41R3341  
1
1
1
1
1
Line cord - Denmark (models CTO 1GG 1HG A1G)  
Line cord - Switzerland (models CTO 1GG 1HG A1G)  
Line cord - Israel (models CTO 1GG 1HG A1G)  
Line cord - South Africa (models CTO 1EM 1GG 1HG A1G A1M)  
Line cord - India (models CTO)  
Table 19. Secondary power cords, type 1106  
1106 Secondary power cords  
FRU#  
CRU  
41R3184  
1
Line cord - US (models CTO 1EU 1EF 1ED 1ES 1EL)  
41R3256  
1
Line cord - China (models CTO)  
80 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 19. Secondary power cords, type 1106 (continued)  
1106 Secondary power cords  
FRU#  
CRU  
24R2633  
45J9595  
41R3176  
41R3196  
41R3260  
41R3224  
1
1
1
1
1
1
Line cord - Japan (models CTO 1EJ)  
Line cord - Brazil (models CTO)  
Line cord - Latin America High Voltage (Argentina, Paraguay, Uraguay) (models CTO 1EY 1EL)  
Line cord - Australia/ New Zealand (models CTO 1EM A1M)  
Line cord - Korea (models CTO)  
Line cord - Hong Kong, United Kingdom, Singapore, Malaysia, Brunei, Ireland, (CTO 1GG  
1HG A1G)  
41R3278  
41R3232  
41R3208  
1
1
1
Line cord - Taiwan (models CTO)  
Line cord - Italy (models CTO 1GG 1HG A1G 1ES 1EL 1EY)  
Line-cord - Indonesia, Laos, Cambodia, Vietnam, Austria, Belgium, Croatia, Czechoslovakia,  
Finland, France, Germany, Hungary, Netherlands, Norway, Poland, Portugal, Romania, Spain,  
Sweden (models CTO)  
41R3212  
41R3228  
41R3236  
41R3220  
41R3341  
1
1
1
1
1
Line cord - Denmark (models CTO 1GG 1HG A1G)  
Line cord - Switzerland (models CTO 1GG 1HG A1G)  
Line cord - Israel (models CTO 1GG 1HG A1G)  
Line cord - South Africa (models CTO 1EM 1GG 1HG A1G A1M)  
Line cord - India (models CTO)  
Chapter 6. Parts listing 81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
82 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7. Configuring the server  
The following configuration programs come with the server:  
• Setup Utility  
The Setup Utility program is part of the server firmware. You can use the Setup Utility program to view  
your server configuration, change the startup device sequence, set the date and time, and set passwords.  
For information about using this program, see “Using the Setup Utility program” on page 83.  
• ThinkServer EasyStartup  
For information about the ThinkServer EasyStartup program, see “Using the ThinkServer EasyStartup  
program” on page 102.  
• EasyUpdate Firmware Updater  
For information about the EasyUpdate Firmware Updater program, see “Using the EasyUpdate Firmware  
Updater program” on page 101.  
Using the Setup Utility program  
The Setup Utility program is used to view and change the configuration settings of your computer, regardless  
of which operating system you are using. However, the operating system settings might override any similar  
settings in the Setup Utility program.  
Starting the Setup Utility program  
To start the Setup Utility program, do the following:  
1. Make sure your computer is turned off.  
2. Repeatedly press and release the F1 key when turning on the computer. When you hear multiple  
beeps or see a logo screen, release the F1 key.  
Note: If a Power-On Password or an Administrator Password has been set, the Setup Utility program  
menu will not be displayed until you type the correct password. For more information, see “Using  
passwords” on page 96.  
When the POST detects that the hard disk drive has been removed from your computer or the memory  
module size has decreased, an error message will be displayed when you start the computer and you will be  
prompted to do one of the following:  
• Press F1 to enter the Setup Utility program. After you enter the Setup Utility program, press F10 to save  
the settings and exit the Setup Utility program. The error message will not be displayed again.  
• Press F2 to bypass the error message and log in to the operating system.  
Introduction of the BIOS items  
The following tables list all the main menus and items in the Setup Utility program.  
Notes:  
• Some items might vary due to BIOS updates.  
• Some items are displayed on the menu only if the server supports the corresponding features.  
• The default settings are already optimized for you. Use the default value for any item you are not familiar  
with. Do not change the value of unfamiliar items or items that are not mentioned in this topic to avoid  
unexpected problems. If you consider changing the server configuration, proceed with extreme caution.  
Setting the configuration incorrectly might cause unexpected results.  
© Copyright Lenovo 2011  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
• Lenovo provides the BIOS update utility on the Lenovo Web site. You can download the BIOS image and  
follow the instructions on the Web site to update the BIOS. See “Updating system programs” on page  
102. After updating the BIOS, all the BIOS settings become the default settings of the updated BIOS  
version. You need to check and reconfigure the BIOS settings for your specific needs.  
• If you have changed any hardware in the server, you might need to reflash the BIOS and the RDX.  
Table 20. Items under the Setup Utility program menu  
Item  
Description  
Main  
Set the basic BIOS parameters. See Table 21 “Items under the Main  
menu” on page 84.  
Devices  
Advanced  
Power  
Set the device parameters. See Table 24 “Items under the Devices menu”  
on page 85.  
Set the advanced BIOS parameters. See Table 31 “Items under the  
Advanced menu” on page 88.  
Set the power parameters. See Table 35 “Items under the Power menu”  
on page 91.  
Security  
Startup  
Set the security parameters. See Table 37 “Items under the Security  
menu” on page 92.  
From the currently detected boot devices, select the first boot device for  
system initialization. See Table 42 “Items under the Startup menu” on  
page 95.  
Exit  
Exit the Setup Utility program. See Table 43 “Items under the Exit menu”  
on page 96.  
Table 21. Items under the Main menu  
Item  
Option or description  
System Summary  
Enter the submenu to view all the options. See Table 22  
“Submenus under the System Summary menu” on page  
85.  
System Time & Date  
Enter the submenu to view all the options. See Table 23  
“Submenus under the System Time & Date menu” on  
page 85.  
Product Name  
Version  
System Brand ID  
Machine Type and Model  
System Serial Number  
Asset Tag  
Serial Number  
Asset Tag Number  
UUID  
System UUID  
Ethernet MAC Address  
BIOS Revision Level  
BIOS Date (MM/DD/YYYY)  
Language  
XX-XX-XX-XX-XX-XX / Not Available  
BIOS Version  
[English] / Français / Chinese  
Notes:  
• [ ] indicates the default setting.  
• The default BIOS language is English. You can change it to French or Chinese on the Main menu.  
84 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Table 22. Submenus under the System Summary menu  
Item  
Option or description  
Show the CPU brand and CPU type.  
Show the CPU speed.  
CPU Type  
CPU Speed  
CPU Core Count  
Installed Memory  
Show the total size of memory installed on the system  
board.  
Memory Bus Speed  
Active Video  
IGD/PEG/PCI  
Onboard Audio  
Onboard Ethernet  
Fan 1  
[Enabled] / Disabled  
[Enabled] / Disabled  
Operating / Not Operating  
Fan 2  
Operating / Not Operating  
SATA Drive 0  
None / Device type: Device model number  
None / Device type: Device model number  
None / Device type: Device model number  
None / Device type: Device model number  
SATA Drive 1  
SATA Drive 2  
SATA Drive 3  
Note: [ ] indicates the default setting.  
Table 23. Submenus under the System Time & Date menu  
Item  
Option  
Description  
Set the system time.  
Set the system date.  
System Time  
HH:MM:SS  
System Date (MM / DD / YYYY)  
MM / DD / YYYY  
Table 24. Items under the Devices menu  
Item  
Description  
Serial Port Setup  
Enter the submenu to view all the options. See Table 25  
“Submenus under the Serial Port Setup menu” on page  
86.  
USB Setup  
Enter the submenu to view all the options. See Table 26  
“Submenus under the USB Setup menu” on page 86.  
ATA Drive Setup  
Enter the submenu to view all the options. See Table 27  
“Submenus under the ATA Drive Setup menu” on page  
86.  
Video Setup  
Audio Setup  
Network Setup  
Enter the submenu to view all the options. See Table 28  
“Submenus under the Video Setup menu” on page 87.  
Enter the submenu to view all the options. See Table 29  
“Submenus under the Audio Setup menu” on page 87.  
Enter the submenu to view all the options. See Table 30  
“Submenus under the Network Setup menu” on page 88.  
Note: Do not change the value of any unfamiliar items under the Devices menu.  
Chapter 7. Configuring the server 85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Table 25. Submenus under the Serial Port Setup menu  
Item  
Option  
Description  
Serial Port1 Address  
Disabled, [3F8/IRQ4], 2F8/IRQ3,  
3E8/IRQ4, 2E8/IRQ3  
Disable or select settings for Serial  
Port 1.  
Note: [ ] indicates the default setting.  
Table 26. Submenus under the USB Setup menu  
Item  
Option  
[Enabled] / Disabled  
Description  
USB Support  
Enable or disable USB functions. If  
it is disabled, no USB device can be  
used.  
USB Legacy Support  
[Enabled] / Disabled  
Enable or disable the USB legacy  
support. When the USB legacy  
support is disabled, the USB  
keyboard and mouse will not function  
unless the device driver is installed.  
Front USB Ports  
Rear USB Ports  
USB Port 1  
[Enabled] / Disabled  
[Enabled] / Disabled  
[Enabled] / Disabled  
[Enabled] / Disabled  
[Enabled] / Disabled  
[Enabled] / Disabled  
[Enabled] / Disabled  
[Enabled] / Disabled  
[Enabled] / Disabled  
[Enabled] / Disabled  
Enable or disable front USB ports.  
Enable or disable rear USB ports.  
Enable or disable USB port 1.  
Enable or disable USB port 2.  
Enable or disable USB port 3.  
Enable or disable USB port 4.  
Enable or disable USB port 5.  
Enable or disable USB port 6.  
Enable or disable USB port 7.  
Enable or disable USB port 8.  
USB Port 2  
USB Port 3  
USB Port 4  
USB Port 5  
USB Port 6  
USB Port 7  
USB Port 8  
Note: [ ] indicates the default setting.  
Table 27. Submenus under the ATA Drive Setup menu  
Item  
Option  
[Enabled] / Disabled  
Description  
External SATA Port  
Enable or disable the external SATA  
port.  
SATA Controller  
[Enabled] / Disabled  
IDE / [AHCI] / RAID  
Enable or disable the SATA controller.  
Configure SATA as  
Select this option to configure your  
system ATA drive.  
Note: Device driver support is  
required for AHCI and RAID.  
Depending on how the hard disk  
image was installed, changing this  
setting may prevent the system from  
booting.  
Native Mode Operation  
[Enabled] / Disabled  
Enable or disable native mode for  
ATA.  
86 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Table 27. Submenus under the ATA Drive Setup menu (continued)  
Item  
Option  
Description  
Hard Disk Pre-delay  
[Disabled] / 3 Seconds / 6 Seconds / 9 Force the BIOS to delay the  
Seconds / 12 Seconds / 15 Seconds initialization of hard disk drives for up  
/ 21 Seconds / 30 Seconds  
to 30 seconds. The delay provides  
your hard disk drives more time to  
spin up before the BIOS initializes  
them.  
Note: [ ] indicates the default setting.  
Table 28. Submenus under the Video Setup menu  
Item  
Option  
Description  
Select Active Video  
IGD / PEG / PCI / [Auto]  
Select the primary video device that  
will be used for graphic output. If you  
select Auto, the system will prioritize  
video devices in the following  
sequence: PEG (PCI-e Graphics  
Device), PCI (PCI Graphics Device),  
and IGD (Internal Graphics Device).  
Notes: When you select IGD, the  
following items will be hidden:  
• Pre-Allocated Memory Size  
• Total Graphics Memory  
• Multi-Monitor Support  
Pre-Allocated Memory Size  
Total Graphics Memory  
32 MB / 64 MB / [128 MB]  
Memory allocated to IGD.  
Total memory allocated to graphics  
devices.  
128MB / 256 MB / [Maximum]  
Note: This function works only  
when you are using the Windows XP  
operating system on your server.  
Enable or disable the multi-monitor  
support function.  
Multi-Monitor Support  
Enabled / [Disabled]  
Note: [ ] indicates the default setting.  
Table 29. Submenus under the Audio Setup menu  
Item  
Option  
[Enabled] / Disabled  
Description  
Enable or disable the onboard audio  
controller.  
Onboard Audio Controller  
Note: [ ] indicates the default setting.  
Chapter 7. Configuring the server 87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Table 30. Submenus under the Network Setup menu  
Item  
Option  
Description  
Enable or disable the onboard  
Ethernet controller.  
Onboard Ethernet Controller  
[Enabled] / Disabled  
Note: If you select Disabled, the  
Intel AMT related functions will be  
disabled.  
Boot Agent  
[PXE] / SMC / Disabled  
Load the onboard PXE (Preboot  
Execution Environment) or SMC  
(Secure Managed Client). This feature  
enables the server to boot from a  
server image.  
Note: [ ] indicates the default setting.  
Table 31. Items under the Advanced menu  
Item  
Description  
CPU Setup  
Enter the submenu to view all the options. See Table 32  
“Submenus under the CPU Setup menu” on page 88.  
Intel® Manageability  
Enter the submenu to view all the options. See Table 33  
“Submenus under the Intel® Manageability menu” on  
page 90.  
Note: The above options might vary depending on the type of the microprocessor.  
Table 32. Submenus under the CPU Setup menu  
Item  
Option  
Description  
Intel® SpeedStep™ Technology  
[Enabled] / Disabled  
Enable or disable the Intel SpeedStep  
technology. This technology enables the  
system to dynamically adjust processor  
voltage and core frequency, which  
can result in decreased average power  
consumption and decreased average heat  
production.  
Enable or disable the multi-core  
processing function.  
Core Multi-Processing  
[Enabled] / Disabled  
[Enabled] / Disabled  
Hyper Threading Technology  
Enable or disable the Hyper Threading  
technology. This technology enables  
multiple logical processors within the  
same processor core to share execution  
resources and cache hierarchy.  
Execute-Disable Bit  
Enable or disable the Execute-Disable Bit  
function. This technology can prevent  
certain classes of malicious buffer overflow  
attacks if your server operating systems  
support this technology.  
[Enabled] / Disabled  
88 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Table 32. Submenus under the CPU Setup menu (continued)  
Item  
Option  
Description  
Intel® Virtualization Technology  
Enable or disable the Intel Virtualization  
technology. This technology can  
provide additional capacity for hardware  
computing. If you set this feature to  
Enabled, you have to turn off the server  
and disconnect the power cord from  
electrical outlet, and then reconnect the  
power cord and turn on the server to have  
this feature take effect.  
Enabled / [Disabled]  
VT-d  
TxT  
Enable or disable VT-d. VT-d support on  
Intel platforms provides the capability  
to ensure improved isolation of I/O  
resources for greater reliability, security,  
and availability.  
Enabled / [Disabled]  
Enabled / [Disabled]  
Enable or disable TxT (Trusted Execution  
Technology). This technology provides  
hardware-based mechanisms that help  
protect against software-based attacks  
and protect the confidentiality and  
integrity of data stored or created on client  
computers. This setting might impact  
system performance.  
Note: If TxT is set to Enabled, the TCG  
security feature will be set to Active  
automatically.  
C State Support  
C1 / C1C3 / [C1C3C6]  
Select supported CPU power management  
status to minimize the idle power  
consumption of the processor.  
• C1: C1 only  
• C1C3: C1 and C3  
• C1C3C6: C1, C3, and C6  
Turbo Mode  
CPU ID  
Enable or disable the Turbo mode. This  
function enables the processor to assess  
its own thermals, current, and power to  
come up with a dynamic upper limit on its  
frequeccy benefit.  
[Enabled] / Disabled  
(MM / DD / YYYY)  
Microcode Revision (MM / DD /  
YYYY)  
Notes:  
1. [ ] indicates the default setting.  
2. The above options might vary depending on the type of the microprocessor.  
Chapter 7. Configuring the server 89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 33. Submenus under the Intel® Manageability menu  
Item  
Option  
Description  
Intel® Manageability Control  
[Enabled] / Disabled  
Enable or disable Intel Manageability  
Control. When this function is  
disabled:  
• If the system is provisioned,  
MEBx (Management Engine BIOS  
Extension) will be unprovisioned  
firstly.  
Note: When you are prompted to  
unprovision MEBx, press YES.  
• The manageability functions will be  
disabled. You can go into MEBx or  
the BIOS to re-enable this function.  
Intel® Manageability Reset  
Enable or disable the Intel  
Manageability Reset function.  
When this function is enabled, Intel  
Manageability settings will be reset  
to defaults. The MEBx password will  
also be reset.  
Enabled / [Disabled]  
[Enabled] / Disabled  
Press <Ctrl-P> to enter MEBx  
SOL Configuration  
Enable or disable the Press <Ctrl-P>  
to enter MEBx function. This function  
provides platform-level configuration  
options for you to configure the  
Management Engine (ME) platform.  
Enter the submenu to view all the  
options. See Table 34 “Submenus  
under the SOL Configuration menu”  
on page 90.  
Notes:  
1. [ ] indicates the default setting.  
2. The above options might vary depending on the type of the microprocessor.  
Table 34. Submenus under the SOL Configuration menu  
Item  
SOL Configuration  
Option  
Description  
Console types:  
• VT100  
Select a console type.  
• VT100 , 8 bit  
• PC-ANSI, 7bit  
• PC-ANSI  
• [VT100+]  
• VT-UTF8  
• ASCII  
Notes:  
1. [ ] indicates the default setting.  
2. The above options might vary depending on the type of the microprocessor.  
90 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Table 35. Items under the Power menu  
Item  
Option  
Description  
After Power Loss  
Power Off / Power On / [Last State]  
This field shows whether the system  
will stay on after ac power is removed  
and then restored.  
• Select Power On if you are using a  
power strip to turn the system on.  
• Select Power Off if you want the  
system to remain off after the  
power is restored.  
• Select Last State to have the  
system return to the previous state.  
Enable or disable Enhanced Power  
Saving Mode. When this function  
is enabled, the system will enter  
Enhanced Power Saving Mode when  
it is powered off. The total power  
consumption will be lower when it is  
turned off.  
Enhanced Power Saving Mode  
[Disabled] / Enabled  
Note: When Enhanced Power Saving  
Mode is enabled, only the Wake  
Up on Alarm function is supported.  
The Intel Manageability Management  
function cannot be used.  
Enable the system to enter the lower  
acoustic level or better thermal level.  
Smart Performance Choice  
Automatic Power On  
[Better Acoustic Performance] / Better  
Thermal Performance  
Enter the submenus to view all the  
options. See Table 36 “Submenus  
under the Automatic Power On  
menu” on page 91.  
Note: [ ] indicates the default setting.  
Table 36. Submenus under the Automatic Power On menu  
Item Option  
Description  
Wake on LAN  
Enable or disable the Wake on LAN  
function and control which startup  
sequence to use after a Wake on LAN  
event.  
Primary / [Automatic] / Disabled  
Note: This item controls the wake-up  
event from onboard LAN and PCI  
LAN.  
Wake from PCI Modem  
[Primary] / Automatic / Disabled  
Enable or disable the Wake from PCI  
Modem function and control which  
startup sequence to use after a PCI  
modem wake-up event.  
Chapter 7. Configuring the server 91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Table 36. Submenus under the Automatic Power On menu (continued)  
Item  
Option  
Description  
Wake from Serial Port Ring  
[Primary] /Automatic / Disabled  
Enable or disable the Wake from  
Serial Port Ring function and controls  
which startup sequence to use after a  
serial port wake-up event.  
Wake from PCI Device  
Wake Up on Alarm  
[Primary] / Automatic / Disabled  
Enable or disable the Wake from PCI  
Device function and control which  
startup sequence to use after a PCI  
device wake-up event.  
Enable or disable the Wake up on  
Alarm function. This function enables  
you to turn on your system on a day  
of the month, a day of the week, or  
daily.  
Single Event / Daily Event / Weekly  
Event / [Disabled]  
Note: Values in these fields might be  
overridden by the operating system.  
Startup Sequence  
[Primary] / Automatic  
[00]:00:00  
Select the startup sequence after a  
Wake Up on Alarm event.  
Alarm Time (HH:MM:SS)  
Alarm Date (MM/DD/YYYY)  
Alarm Day of Week  
Specify the time when the system is  
to wake up.  
[01] / 01 / 1999  
Specify the date when the system is  
to wake up.  
[Sunday] / Monday / Tuesday /  
Wednesday /Thursday / Friday /  
Saturday  
Select the day of the week when the  
system is to wake up.  
Note: [ ] indicates the default setting.  
Table 37. Items under the Security menu  
Item  
Option  
[Enabled] / Disabled  
Registered / Disabled / [Enabled]  
Not Installed / Installed  
Not Installed / Installed  
Enter  
Description  
Hardware Password Manager  
Current setting  
Administrator Password  
Power-On Password  
Set Administrator Password  
Configure this item to set, change, or  
delete the Administrator Password.  
To set a password, use characters  
a-z and 0-9. Passwords are not case  
sensitive.  
Note: To delete the Administrator  
Password, clear the corresponding  
fields for each password.  
Enter  
Set Power-On Password  
Configure this item to set, change, or  
delete the Administrator Password.  
To set a password, use characters  
a-z and 0-9. Passwords are not case  
sensitive.  
Note: To delete the Power-On  
Password, clear the corresponding  
fields for each password.  
92 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Table 37. Items under the Security menu (continued)  
Item  
Option  
Description  
Require Admin Password when  
Flashing  
If No is selected, the Administrator  
Password will not be required when  
updating the system software.  
Yes / [No]  
Yes / [No]  
Require POP on Restart  
Hard Disk Password  
If No is selected, the Power-On  
Password will only be required when  
the system is started with a cold boot.  
Enter the submenus to view all the  
options. See Table 38 “Submenus  
under the Hard Disk Password  
menu” on page 93.  
Enter the submenus to view all the  
options. See Table 39 “Submenus  
under the Fingerprint Setup menu”  
on page 94.  
Fingerprint Setup  
TCG Feature Setup  
System Event Log  
Enter the submenus to view all the  
options. See Table 40 “Submenus  
under the TCG Feature Setup  
submenu” on page 94.  
Enter the submenus to view all the  
options. See Table 41 “Submenus  
under the System Event Log menu”  
on page 94.  
Configuration Change Detection  
Enabled / [Disabled]  
Enable or disable Configuration  
Change Detection.  
Note: [ ] indicates the default setting.  
Table 38. Submenus under the Hard Disk Password menu  
Item  
Option  
[Disabled] / User / User + Master  
Description  
The Hard Disk Password prevents  
unauthorized users from accessing  
the data on the hard disk drive. In  
addition to the User Password, an  
optional Master Password can be  
used to recover the hard disk drive if  
the User Password is lost.  
SATA Drive 0 Password  
Note: If multiple hard disk drives are  
present, it is recommended to set the  
same password for all the hard disk  
drives.  
The Hard Disk Password prevents  
unauthorized users from accessing  
the data on the hard disk drive. In  
addition to the User Password, an  
optional Master Password can be  
used to recover the hard disk drive if  
the User Password is lost.  
SATA Drive 1 Password  
[Disabled] / User / User + Master  
Note: If multiple hard disk drives are  
present, it is recommended to set the  
same password for all the hard disk  
drives.  
Chapter 7. Configuring the server 93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Table 38. Submenus under the Hard Disk Password menu (continued)  
Item  
Option  
Description  
Require HDP on Restart  
If No is selected, the Hard Disk  
Password will only be required when  
the system is started with a cold boot.  
Note: It is highly recommended to  
set this value to Yes to achieve the  
highest level of security.  
Yes / [No]  
Note: [ ] indicates the default setting.  
Table 39. Submenus under the Fingerprint Setup menu  
Item  
Option  
[Enabled] / Disabled  
Description  
Preboot Authentication  
Enable or disable the fingerprint  
reader function for BIOS password  
input.  
Erase Fingerprint Data  
Yes / [No]  
Select whether to clear fingerprint  
data stored in a fingerprint reader.  
Note: [ ] indicates the default setting.  
Table 40. Submenus under the TCG Feature Setup submenu  
Item  
Option  
Description  
TCG Security Feature  
Active / [Inactive] / Disabled  
Change the TCG Security Feature  
settings.  
• Active: The feature is fully  
functional.  
• Inactive: The feature is visible, but  
is not functional.  
• Disabled: The feature is hidden  
and not functional.  
Note: When you set it as Inactive  
or Disabled, the TxT will be set to  
Disabled automatically.  
Clear TCG Security Feature  
Yes / [No]  
Select whether to clear TCG Security  
Feature settings.  
Note: [ ] indicates the default setting.  
Table 41. Submenus under the System Event Log menu  
Item  
View System Event Log  
Description  
View the system event log.  
Clear the system event log.  
Clear System Event Log  
94 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Table 42. Items under the Startup menu  
Item  
Option  
Description  
This sequence is used when the  
system starts normally. Press the  
Up and Down arrow keys to select a  
device.  
Primary Boot Sequence  
This sequence is used when a  
communication device wakes the  
system up. Press the Up and Down  
arrow keys to select a device.  
Automatic Boot Sequence  
Error Boot Sequence  
Boot Mode  
This sequence is used when the  
BIOS determines that an error has  
occurred. Press the Up and Down  
arrow keys to select a device.  
[Auto] / UEFI / Legacy  
Choose boot policy:  
• Auto: The system will prioritize  
boot options in bootable devices  
by running UEFI boot options first  
and then processing Legacy boot  
options.  
• UEFI: The system will boot from  
UEFI bootable devices only.  
• Legacy: The system will boot from  
Legacy bootable devices only.  
Quick Boot  
[Enabled] / Disabled  
[On] / Off  
Select Enabled to obtain the fastest  
boot time. Select Disabled to test  
for a stuck key during the POST and  
you may hear a beep after POST  
completes.  
Boot Up Num-Lock Status  
This field indicates the state of the  
NumLock feature of the keyboard  
after startup.  
• If NumLock is On, the keys on the  
keyboard will act as numeric keys.  
• If NumLock is Off, the keys on the  
keyboard will act as cursor keys.  
Enable or disable the keyboardless  
operation. This function enables  
the system to function without a  
keyboard. It is commonly used when  
the system has been set up as a  
network server.  
Keyboardless Operation  
Enabled / [Disabled]  
Note: If it is enabled, systems without  
keyboards will not display keyboard  
errors during the POST.  
Option Keys Display  
[Enabled] / Disabled  
Enable or disable the Option Keys  
Display function. When this function  
is enabled, the system software  
option key (such as the F1 key)  
prompts will be displayed.  
Note: Disabling the prompts will not  
affect the function of a specific key.  
Chapter 7. Configuring the server 95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Table 42. Items under the Startup menu (continued)  
Item  
Option  
[Normal] / Legacy  
Description  
Option Keys Display Style  
Control the prompts displayed on the  
POST logo screen.  
• Normal: During the POST, this  
message will be displayed: To  
interrupt normal startup, press  
Enter.  
• Legacy: During the POST, this  
message will be displayed: Press  
F1 to enter Setup and press F12 to  
display Boot Menu.  
Startup Device Menu Prompt  
[Enabled] / Disabled  
Enable or disable the Startup Device  
Menu Prompt. This function enables  
the Startup Device Menu to be  
displayed by pressing F12 after the  
server is turned on. The Startup  
Device Menu enables the sequence  
of startup devices to be temporarily  
changed.  
Note: [ ] indicates the default setting.  
Table 43. Items under the Exit menu  
Item  
Description  
Save Changes and Exit  
Discard Changes and Exit  
Load Optimal Defaults  
Exit the Setup Utility program after saving the changes.  
Exit the Setup Utility program without saving any changes.  
Restore/Load default values for all the setup options.  
Viewing and changing settings  
The Setup Utility program menu lists various items about the system configuration. To view or change  
settings, start the Setup Utility program. See “Starting the Setup Utility program” on page 83. Then, follow  
the instructions on the screen.  
You can use either the keyboard or the mouse to navigate through BIOS menu choices. The keys used to  
perform various tasks are displayed at the bottom of each screen.  
Using passwords  
By using the Setup Utility program, you can set passwords to prevent unauthorized access to your computer  
and data. The following types of passwords are available:  
• Power-On Password  
• Administrator Password  
• Hard Disk Password  
You do not have to set a password to use your computer. However, using passwords improves computing  
security. If you decide to set a password, read the following sections.  
96 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Password considerations  
A password can be any combination of up to 64 alphabetic and numeric characters. For security reasons, it  
is recommended to use a strong password that cannot be easily compromised. To set a strong password,  
use the following guidelines:  
• Have at least eight characters in length  
• Contain at least one alphabetic character and one numeric character  
• Setup Utility program and hard disk drive passwords are not case sensitive  
• Not be your name or your user name  
• Not be a common word or a common name  
• Be significantly different from your previous passwords  
Power-On Password  
When a Power-On Password is set, you are prompted to type a valid password each time the computer is  
turned on. The computer cannot be used until the valid password is typed in.  
Administrator Password  
Setting an Administrator Password deters unauthorized users from changing configuration settings. If you  
are responsible for maintaining the configuration settings of several computers, you might want to set an  
Administrator Password.  
When an Administrator Password is set, you are prompted to type a valid password each time you try to  
access the Setup Utility program. The Setup Utility program cannot be accessed until a valid password  
is typed in.  
If both the Power-On Password and Administrator Password are set, you can type either password. However,  
you must use your Administrator Password to change any configuration settings.  
Hard Disk Password  
Setting a Hard Disk Password prevents unauthorized access to the data on the hard disk drive. When a  
Hard Disk Password is set, you are prompted to type a valid password each time you try to access the  
hard disk drive.  
Notes:  
• After you set a Hard Disk Password, your data on the hard disk drive is protected even if the hard disk  
drive is removed from one computer and installed in another.  
• If the Hard Disk Password is forgotten, there is no way to reset the password or recover data from the  
hard disk drive.  
Setting, changing, and deleting a password  
To set, change, or delete a password, do the following:  
1. Start the Setup Utility program. See “Starting the Setup Utility program” on page 83.  
2. From the Setup Utility program main menu, select Security.  
3. Depending on the password type, select Set Power-On Password, Set Administrator Password, or  
Hard Disk Password.  
4. Follow the instructions on the right side of the screen to set, change, or delete a password.  
Note: A password can be any combination of up to 64 alphabetic and numeric characters. For more  
information, see “Particulate contamination” on page 112.  
Chapter 7. Configuring the server 97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Erasing lost or forgotten passwords (clearing CMOS)  
This section provides instructions on how to erase lost or forgotten passwords, such as a user password.  
To erase a lost or forgotten password, do the following:  
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all  
power cords from electrical outlets and disconnect all cables that are connected to the server.  
2. Remove the server cover. See “Removing the server cover” on page 33.  
3. Locate the Clear CMOS /Recovery jumper on the system board. See “Locating parts on the system  
board” on page 26.  
4. Remove all parts and disconnect all cables that might prevent your access to the Clear CMOS  
/Recovery jumper.  
Note: If your server has a secondary hard disk drive installed, remove the secondary hard disk drive  
to access the Clear CMOS /Recovery jumper. See “Installing or replacing the secondary hard disk  
drive” on page 46.  
5. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and  
pin 3).  
6. Reinstall all parts and reconnect all cables that have been removed.  
7. Reinstall the server cover and reconnect the server power cord. See “Completing the parts replacement”  
on page 66.  
8. Turn on the server and leave it on for approximately 10 seconds. Then, turn off the server by holding the  
power switch for approximately five seconds.  
9. Repeat step 1 through step 4.  
10. Move the Clear CMOS /Recovery jumper back to the standard position (pin 1 and pin 2).  
11. Reinstall all parts and reconnect all cables that have been removed.  
12. Reinstall the server cover and connect the power cords. See “Completing the parts replacement”  
on page 66.  
Enabling or disabling a device  
This section provides information on how to enable or disable user access to the following devices:  
USB Setup  
Use this option to enable or disable a USB connector. When a USB connector is  
disabled, the device connected to the USB connector cannot be used.  
SATA Controller  
External SATA Port  
When this feature is set to Disabled, all devices connected to the SATA connectors  
(such as hard disk drives or the optical drive) are disabled and cannot be accessed.  
When this option is set to Disabled, the device connected to the External SATA  
connector cannot be accessed.  
To enable or disable a device, do the following:  
1. Start the Setup Utility program. See “Starting the Setup Utility program” on page 83.  
2. From the Setup Utility program main menu, select Devices.  
3. Depending on the device you want to enable or disable, do one of the following:  
• Select USB Setup to enable or disable a USB device.  
• Select ATA Drive Setup to enable or disable an internal or external SATA device.  
4. Select the desired settings and press Enter.  
5. Press F10 to save changes and exit the Setup Utility program. See “Exiting from the Setup Utility  
program” on page 99.  
98 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Selecting a startup device  
If your computer does not start up from a device such as the disc or hard disk drive as expected, do one of  
the following to select the startup device you want.  
Selecting a temporary startup device  
Use this procedure to select a temporary startup device.  
Note: Not all discs and hard disk drives are bootable.  
1. Turn off your computer.  
2. Repeatedly press and release the F12 key when turning on the computer. When the “Please select  
boot device” window opens, release the F12 key.  
3. Select the desired startup device and press Enter. The computer will start up from the device you  
selected.  
Note: Selecting a startup device from the “Please select boot device” window does not permanently  
change the startup sequence.  
Selecting or changing the startup device sequence  
To view or permanently change the configured startup device sequence, do the following:  
1. Start the Setup Utility program. See “Starting the Setup Utility program” on page 83.  
2. From the Setup Utility program main menu, select Startup.  
3. Select the devices for the Primary Startup Sequence, the Automatic Startup Sequence, and the Error  
Startup Sequence. Read the information displayed on the right side of the screen.  
4. Press F10 to save changes and exit the Setup Utility program. See “Exiting from the Setup Utility  
program” on page 99.  
Exiting from the Setup Utility program  
After you finish viewing or changing settings, press Esc to return to the Setup Utility program main menu.  
You might have to press Esc several times. Do one of the following:  
• If you want to save the new settings, press F10 to save and exit the Setup Utility program.  
• If you do not want to save the settings, select Exit ➙ Discard Changes and Exit.  
• If you want to return to the default settings, press F9 to load the default settings.  
Configuring RAID  
This topic provides information about how to configure Redundant Array of Independent Disks (RAID) for  
your server.  
Note: The information about configuring RAID in this topic is applicable only in a Windows environment. For  
information about configuring RAID in a Linux environment, contact your Linux software provider.  
RAID level  
Your server must have the minimum number of SATA hard disk drives installed for the supported level of  
RAID to function:  
• RAID Level 0 – Striped disk array  
– Two hard disk drives minimum  
– Better performance without fault tolerance  
• RAID Level 1 – Mirrored disk array  
Chapter 7. Configuring the server 99  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
– Two hard disk drives minimum  
– Improved read performance and 100% redundancy  
To install a secondary hard disk drive, refer to “Installing or replacing the secondary hard disk drive”  
on page 46.  
Configuring the system BIOS to enable SATA RAID functionality  
This section describes how to configure the system BIOS to enable SATA RAID functionality.  
Note: Use the arrow keys on the keyboard to make selections.  
To enable SATA RAID functionality, do the following:  
1. Start the Setup Utility program. See “Starting the Setup Utility program” on page 83.  
2. Select Devices ➙ ATA Drive Setup.  
3. Select Configure SATA as and press Enter.  
4. Select RAID Mode and press Enter.  
5. Press F10 to save changes and exit the Setup Utility program.  
Creating RAID volumes  
This section describes how to use the Intel Matrix Storage Manager option ROM configuration utility to  
create RAID volumes.  
To create RAID volumes, do the following:  
1. Press Ctrl+I when prompted to enter the Intel Matrix Storage Manager option ROM configuration utility  
during system startup.  
2. Use the up and down arrow keys to select Create RAID Volume and press Enter.  
3. Type a proper RAID volume name in the Name field and press Tab.  
4. Use the arrow keys to select a RAID level in the RAID Level field and press Tab.  
5. If appropriate, use the arrow keys to select a stripe size in the Stripe Size field and press Tab.  
6. Type a volume size in the Capacity field and press Tab.  
7. Press Enter to initiate volume creation.  
8. When prompted, press Y to accept the warning message and create the volume.  
9. If desired, return to step 2 to create additional RAID volumes.  
10. When finished, select Exit and press Enter.  
Deleting RAID volumes  
This section describes how to use the Intel Matrix Storage Manager option ROM configuration utility to  
delete RAID volumes.  
To delete RAID volumes, do the following:  
1. Press Ctrl+I when prompted to enter the Intel Matrix Storage Manager option ROM configuration utility  
during system startup.  
2. Use the up and down arrow keys to select Delete RAID Volume and press Enter.  
3. Use the arrow keys to select the RAID volume to be deleted and press Delete.  
4. When prompted, press Y to confirm the deletion of the selected RAID volume. Deleting a RAID volume  
will reset the hard disk drives to non-RAID.  
5. After deleting a RAID volume, you can:  
100 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
• Return to step 2 to delete additional RAID volumes.  
• See “Creating RAID volumes” on page 100 for RAID volume creation.  
• Use the up and down arrow keys to select Exit and press Enter.  
Resetting disks to non-RAID  
This section describes how to reset your hard disk drives to non-RAID.  
To reset your hard disk drives to non-RAID, do the following:  
1. Press Ctrl+I when prompted to enter the Intel Matrix Storage Manager option ROM configuration utility  
during system startup.  
2. Use the up and down arrow keys to select Reset Disks to Non-RAID and press Enter.  
3. Use the arrow keys and the space key to mark individual physical hard disk drives to be reset, and then  
press Enter to complete the selection.  
4. When prompted, press Y to confirm the reset action.  
5. After resetting the hard disk drives to non-RAID, you can:  
• See “Deleting RAID volumes” on page 100 for RAID volume deletion.  
• See “Creating RAID volumes” on page 100 for RAID volume creation.  
• Use the up and down arrow keys to select Exit and press Enter.  
Updating the firmware  
The firmware in the server is periodically updated and is available for download on the Lenovo Support Web  
site. Go to http://www.lenovo.com/support to check for the latest level of firmware, such as the BIOS  
ROM file and RAID FW files.  
When you replace a device in the server, you might have to either update the server with the latest version of  
the firmware that is stored in memory on the device or restore the pre-existing firmware from a diskette or  
CD image.  
• The BIOS ROM file is stored in flash on the system board.  
• The onboard SATA software RAID firmware is integrated into the BIOS ROM on the system board.  
The Ethernet firmware is downloadable at http://www.lenovo.com/support.  
Using the EasyUpdate Firmware Updater program  
ThinkServer EasyUpdate Firmware Updater is a software application that enables you to maintain your  
system firmware up-to-date and helps you avoid unnecessary outages. Firmware Updater updates the  
server system and adapter firmware.  
To update your system, do the following:  
1. Go to http://www.lenovo.com/support.  
2. Click Download & Drivers ➙ ThinkServer and then follow the instructions on the Web page to  
download the ISO image for the EasyUpdate Firmware Updater program.  
3. Burn the ISO image to a disc.  
4. Set the optical drive as the first boot device and insert the disc into the optical drive. The server will  
proceed directly to the User Interface Application’s introductory screen.  
5. Read the messages and instructions displayed on the introductory screen. Then, click Next to proceed  
to the list of firmware updates available on the optical media.  
Chapter 7. Configuring the server 101  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
6. Click Apply to begin the updates (click Cancel if you want to abort the updates and exit). All updates  
will run to completion, with each updater’s native user interface kept visible to the user. When the User  
Interface Application regains control, you will see the results screen.  
Before distributing the firmware update to other servers, ensure that your server can restart successfully  
without encountering hardware problems.  
Notes:  
1. If you have changed any hardware (except the hard disk drives) in the server, you must reflash the  
BIOS and the RDX.  
2. After updating the BIOS, all the BIOS settings become the default settings of the updated BIOS version.  
You need to check and reconfigure the BIOS settings for your specific needs.  
Using the ThinkServer EasyStartup program  
The ThinkServer EasyStartup DVD simplifies the process of configuring your RAID controllers and installing  
an operating system. The program works in conjunction with your Windows operating-system installation  
disc to automate the process of installing the operating systems and associated device drivers.  
If you did not receive a ThinkServer EasyStartup DVD with your server, you can download an image from the  
Lenovo Support Web site at http://www.lenovo.com/support.  
The EasyStartup program has the following features:  
• Self-booting DVD  
• Easy-to-use, language-selectable interface  
• Integrated help system  
• Automatic hardware detection  
• RAID configuration utility  
• Device drivers provided based on the server model and detected devices  
• Selectable partition size and file system  
• Support for multiple operating systems  
• Installing the operating system and device drivers in an unattended mode to save time  
• Creating a reuseable response file that can be used with similarly configured Lenovo servers to make  
future installations even faster  
Updating system programs  
This topic provides information about updating the POST and BIOS, and how to recover from a POST  
and BIOS update failure.  
Using system programs  
System programs are the basic layer of software built into your computer. System programs include the  
POST, the BIOS, and the Setup Utility program. The POST is a set of tests and procedures that are  
performed each time you turn on your computer. The BIOS is a layer of software that translates instructions  
from other layers of software into electrical signals that the computer hardware can execute. You can use the  
Setup Utility program to view or change the configuration settings of your computer. See “Using the Setup  
Utility program” on page 83 for detailed information.  
Your computer system board has a module called electrically erasable programmable read-only memory  
(EEPROM, also referred to as flash memory). You can easily update the POST, the BIOS, and the Setup  
102 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Utility program by starting your computer with a system-program-update disc or running a special update  
program from your operating system.  
Lenovo might make changes and enhancements to the POST and BIOS. When updates are released, they  
are available as downloadable files on the Lenovo Web site at http://www.lenovo.com. Instructions for using  
the POST and BIOS updates are available in a TXT file that is included with the update files. For most  
models, you can download either an update program to create a system-program-update disc or an update  
program that can be run from the operating system.  
Updating (flashing) the BIOS from a disc  
This section provides instructions on how to update (flash) the BIOS from a disc.  
Note: You can download a self-starting bootable disc image (known as an ISO image) with the system  
program updates to create a system-program-update disc. Go to:  
http://www.lenovo.com/support  
To update (flash) the BIOS from a disc, do the following:  
1. Turn off your computer.  
2. Repeatedly press and release the F12 key when turning on the computer. When the Startup Device  
Menu opens, release the F12 key.  
3. On the Startup Device Menu, select the desired optical drive as the startup device. Then, insert the  
disc into this optical drive and press Enter. The update begins.  
4. When prompted to change the serial number, it is suggested that you do not make this change by  
pressing N. However, if you do want to change the serial number, press Y, then type in the serial number  
and press Enter.  
5. When prompted to change the machine type and model, it is suggested that you do not make this  
change by pressing N. However, if you do want to change the machine type and model, press Y, then  
type in the machine type and model and press Enter.  
6. Follow the instructions on the screen to complete the update. After the update is completed, remove the  
disc from the optical drive.  
Updating (flashing) the BIOS from your operating system  
Note: Because Lenovo makes constant improvements to its Web sites, the Web page contents are subject  
to change without notice, including the contents referenced in the following procedure.  
To update (flash) the BIOS from your operating system, do the following:  
1. Go to http://www.lenovo.com/support.  
2. Do the following to locate the downloadable files for your machine type:  
a. In the Enter a product number field, type your machine type and click Go.  
b. Click Downloads and drivers.  
c. Select BIOS from the Refine results drop-down list box to easily locate all the BIOS related links.  
d. Click the BIOS update link.  
3. Click the TXT file that contains the instructions for updating (flashing) the BIOS from your operating  
system.  
4. Print these instructions. This is very important because these instructions will not be displayed on  
the screen after the download begins.  
5. Follow the printed instructions to download, extract, and install the update.  
Chapter 7. Configuring the server 103  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Recovering from a POST and BIOS update failure  
If the power to your computer is interrupted while the POST and BIOS are being updated, your computer  
might not restart correctly. If this happens, perform the following procedure to recover from the POST and  
BIOS update failure. This procedure is commonly called Boot-block Recovery.  
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect  
all power cords from electrical outlets and disconnect all cables that are connected to the computer.  
2. Remove the computer cover. See “Removing the server cover” on page 33.  
3. Locate the Clear CMOS /Recovery jumper on the system board. See “Locating parts on the system  
board” on page 26.  
4. Remove any cables that impede access to the Clear CMOS /Recovery jumper.  
5. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and  
pin 3).  
6. Reconnect any cables that were disconnected and reinstall the PCI card if removed.  
7. Reinstall the computer cover and reconnect the power cords for the computer and monitor to electrical  
outlets. See “Completing the parts replacement” on page 66.  
8. Turn on the computer and then insert the POST and BIOS update (flash update) disc into the optical  
drive. The recovery session begins. The recovery session will take two to three minutes. During this  
time, you will hear a series of beeps.  
9. After the recovery session is completed, the series of beeps will end, and the system will automatically  
turn off. Remove the disc from the optical drive before the system completely turns off.  
10. Repeat step 1 through step 4.  
11. Move the Clear CMOS /Recovery jumper back to the standard position (pin 1 and pin 2).  
12. Reconnect any cables that were disconnected and reinstall the PCI card if removed.  
13. Reinstall the computer cover and reconnect any cables that were disconnected.  
14. Turn on the computer to restart the operating system.  
104 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Appendix A. Information resources  
You can use the information in this appendix to access useful resources relating to your computing needs.  
Safety and Warranty  
The Safety Information and the Warranty and Support Information at http://www.lenovo.com/support  
contain information on safety, setup, warranty, and notices. Read and understand all safety information  
before using this product.  
Lenovo Web site (http://www.lenovo.com)  
The Lenovo Web site provides up-to-date information and services to help you buy, upgrade, and maintain  
your computer. You can also do the following:  
• Shop for desktop, workstation, and notebook computers, monitors, projectors, upgrades and accessories  
for your computer, and special offers.  
• Purchase additional services, such as support for hardware, operating systems, application programs,  
network setup and configuration, and custom installations.  
• Purchase upgrades and extended hardware repair services.  
• Download the latest device drivers and software updates for your computer model.  
• Access the online manuals for your products.  
• Access the Lenovo Limited Warranty.  
• Access troubleshooting and support information for your computer model and other supported products.  
• Find the service and support phone numbers for your country or region.  
• Find a Service Provider located near you.  
Lenovo Support Web site  
Technical support information is available at:  
http://www.lenovo.com/support  
This portal is updated with the latest information about the following subjects:  
Downloads and Drivers  
Warranty  
Download drivers, flash BIOS, and update your software.  
Check your warranty status and upgrade your warranty.  
Click Need Help? for self-help tips to help diagnose a problem.  
Technical Support  
ThinkVantage  
Learn more about ThinkVantage software to improve productivity and  
reduce cost.  
Lenovo Forums  
Search the community knowledge base for your computer to share and  
discover information with other users.  
Read or print any publications related to your product.  
User Guides & Manuals  
© Copyright Lenovo 2011  
105  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
106 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix B. Help and service  
This appendix contains information about obtaining help and service.  
Using the documentation  
If you experience a problem with your computer, see Chapter 3 “Diagnostics and troubleshooting” on page  
13. For information on additional resources to help you troubleshoot your computer problem, see Appendix  
A “Information resources” on page 105.  
If you suspect a software problem, see the documentation that comes with the operating system or software  
program, including readme files and online help.  
You can also get the latest technical information and download device drivers and updates from the Lenovo  
Support Web site at:  
http://www.lenovo.com/support  
Calling for service  
During the warranty period, you can get help and information by telephone through the Customer Support  
Center.  
The following services are available during the warranty period:  
• Problem determination - Trained service personnel are available to assist you with determining a  
hardware problem and deciding what action is necessary to fix the problem.  
• Hardware repair - If the problem is caused by hardware under warranty, trained service personnel are  
available to provide the applicable level of service.  
• Engineering Change management - There might be changes that are required after a product has  
been sold. Lenovo or your reseller will make selected Engineering Changes (ECs) that apply to your  
hardware available.  
These items are not covered by the warranty:  
• Replacement or use of parts not manufactured for or by Lenovo or non-warranted Lenovo parts  
• Identification of software problem sources  
• Configuration of BIOS as part of an installation or upgrade  
• Changes, modifications, or upgrades to device drivers  
• Installation and maintenance of network operating systems (NOS)  
• Installation and maintenance of application programs  
Refer to the Warranty and Support Information that comes with your computer for information about your  
warranty type and duration. You must retain your proof of purchase to obtain warranty service.  
For a list of the Lenovo Support phone numbers for your country or region, go to  
http://www.lenovo.com/support/phone or refer to the Warranty and Support Information that comes with  
your computer.  
Note: Phone numbers are subject to change without notice. If the number for your country or region is not  
provided, contact your Lenovo reseller or Lenovo marketing representative.  
If possible, be at your computer when you call. Have the following information available:  
• Machine type and model  
© Copyright Lenovo 2011  
107  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
• Serial numbers of your hardware products  
• Description of the problem  
• Exact wording of any error messages  
• Hardware and software configuration information  
Using other services  
If you travel with your computer or relocate it to a country where your desktop or notebook computer  
machine type is sold, your computer might be eligible for International Warranty Service, which automatically  
entitles you to obtain warranty service throughout the warranty period. Service will be performed by service  
providers authorized to perform warranty service.  
Service methods and procedures vary by country, and some services might not be available in all countries.  
International Warranty Service is delivered through the method of service (such as depot, carry-in, or  
on-site service) that is provided in the servicing country. Service centers in certain countries might not be  
able to service all models of a particular machine type. In some countries, fees and restrictions might  
apply at the time of service.  
To determine whether your computer is eligible for International Warranty Service and to view a list of the  
countries where service is available, go to http://www.lenovo.com/support, click Warranty, and follow  
the instructions on the screen.  
For technical assistance with the installation of or questions related to Service Packs for your  
preinstalled Microsoft Windows product, refer to the Microsoft Product Support Services Web site at  
http://support.microsoft.com/directory or you can contact the Customer Support Center. Some fees might  
apply.  
Purchasing additional services  
During and after the warranty period, you can purchase additional services, such as support for hardware,  
operating systems, and application programs; network setup and configuration; upgraded or extended  
hardware repair services; and custom installations. Service availability and service name might vary by  
country or region. For more information about these services, go to the Lenovo Web site at:  
http://www.lenovo.com  
108 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Appendix C. Notices  
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult  
your local Lenovo representative for information on the products and services currently available in your  
area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that  
Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service  
that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user's  
responsibility to evaluate and verify the operation of any other product, program, or service.  
Lenovo may have patents or pending patent applications covering subject matter described in this  
document. The furnishing of this document does not give you any license to these patents. You can send  
license inquiries, in writing, to:  
Lenovo (United States), Inc.  
1009 Think Place - Building One  
Morrisville, NC 27560  
U.S.A.  
Attention: Lenovo Director of Licensing  
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS  
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow  
disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply  
to you.  
This information could include technical inaccuracies or typographical errors. Changes are periodically  
made to the information herein; these changes will be incorporated in new editions of the publication.  
Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this  
publication at any time without notice.  
The products described in this document are not intended for use in implantation or other life support  
applications where malfunction may result in injury or death to persons. The information contained in this  
document does not affect or change Lenovo product specifications or warranties. Nothing in this document  
shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo  
or third parties. All information contained in this document was obtained in specific environments and is  
presented as an illustration. The result obtained in other operating environments may vary.  
Lenovo may use or distribute any of the information you supply in any way it believes appropriate without  
incurring any obligation to you.  
Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in  
any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of  
the materials for this Lenovo product, and use of those Web sites is at your own risk.  
Any performance data contained herein was determined in a controlled environment. Therefore, the result  
obtained in other operating environments may vary significantly. Some measurements may have been  
made on development-level systems and there is no guarantee that these measurements will be the same  
on generally available systems. Furthermore, some measurements may have been estimated through  
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their  
specific environment.  
© Copyright Lenovo 2011  
109  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Trademarks  
The following terms are trademarks of Lenovo in the United States, other countries, or both:  
Lenovo  
The Lenovo logo  
ThinkServer  
Microsoft, Windows, and Windows Server are trademarks of the Microsoft group of companies.  
Intel and Intel SpeedStep are trademarks of Intel Corporation in the United States, other countries, or both.  
Other company, product, or service names may be trademarks or service marks of others.  
Important notes  
Processor speed indicates the internal clock speed of the microprocessor; other factors also affect  
application performance.  
CD or DVD drive speed is the variable read rate. Actual speeds vary and are often less than the possible  
maximum.  
When referring to processor storage, real and virtual storage, or channel volume, KB stands for 1 024 bytes,  
MB stands for 1 048 576 bytes, and GB stands for 1 073 741 824 bytes.  
When referring to hard disk drive capacity or communications volume, MB stands for 1 000 000 bytes,  
and GB stands for 1 000 000 000 bytes. Total user-accessible capacity can vary depending on operating  
environments.  
Maximum internal hard disk drive capacities assume the replacement of any standard hard disk drives  
and population of all hard disk drive bays with the largest currently supported drives that are available  
from Lenovo.  
Maximum memory might require replacement of the standard memory with an optional memory module.  
Lenovo makes no representations or warranties with respect to non-Lenovo products. Support (if any) for  
the non-Lenovo products is provided by the third party, not Lenovo.  
Some software might differ from its retail version (if available) and might not include user manuals or all  
program functionality.  
Polyvinyl Chloride (PVC) cable and cord notice  
WARNING: Handling the cord on this product or cords associated with accessories sold with this product  
will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or  
other reproductive harm. Wash hands after handling.  
Recycling information  
Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment  
when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in  
recycling their IT products. For information on recycling Lenovo products, go to:  
http://www.lenovo.com/lenovo/environment/recycling  
110 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Collecting and recycling a disused Lenovo computer or monitor  
If you are a company employee and need to dispose of a Lenovo computer or monitor that is the property  
of the company, you must do so in accordance with the Law for Promotion of Effective Utilization of  
Resources. Computers and monitors are categorized as industrial waste and should be properly disposed  
of by an industrial waste disposal contractor certified by a local government. In accordance with the Law  
for Promotion of Effective Utilization of Resources, Lenovo Japan provides, through its PC Collecting and  
Recycling Services, for the collecting, reuse, and recycling of disused computers and monitors. For details,  
visit the Lenovo Web site at http://www.lenovo.com/social_responsibility/us/en/sustainability/ptb_japan.html.  
Pursuant to the Law for Promotion of Effective Utilization of Resources, the collecting and recycling of  
home-used computers and monitors by the manufacturer was begun on October 1, 2003. This service is  
provided free of charge for home-used computers sold after October 1, 2003. For details, visit the Lenovo  
Web site at http://www.lenovo.com/social_responsibility/us/en/sustainability/ptb_japan.html.  
Disposing of Lenovo computer components  
Some Lenovo computer products sold in Japan may have components that contain heavy metals or other  
environmental sensitive substances. To properly dispose of disused components, such as a printed circuit  
board or drive, use the methods described above for collecting and recycling a disused computer or monitor.  
Battery return program  
This product may contain a lithium or lithium ion battery. Consult your user manual or service manual for  
specific battery information. The battery must be recycled or disposed of property. Recycling facilities may  
not be available in your area. For information on disposal or batteries outside the United States, go to  
http://www.lenovo.com/lenovo/environment/recycling or contact your local waste disposal facility.  
For Taiwan: Please recycle batteries.  
Appendix C. Notices 111  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
For the European Union:  
Notice: This mark applies only to countries within the European Union (EU).  
Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC  
concerning batteries and accumulators and waste batteries and accumulators. The Directive determines the  
framework for the return and recycling of used batteries and accumulators as applicable throughout the  
European Union. This label is applied to various batteries to indicate that the battery is not to be thrown  
away, but rather reclaimed upon end of life per this Directive.  
Les batteries ou emballages pour batteries sont étiquetés conformément aux directives européennes  
2006/66/EC, norme relative aux batteries et accumulateurs en usage et aux batteries et accumulateurs  
usés. Les directives déterminent la marche à suivre en vigueue dans l'Union Européenne pour le retour et  
le recyclage des batteries et accumulateurs usés. Cette étiquette est appliquée sur diverses batteries  
pour indiquer que la batterie ne doit pas être mise au rebut mais plutôt récupérée en fin de cycle de vie  
selon cette norme.  
In accordance with the European Directive 2006/66/EC, batteries and accumulators are labeled to indicate  
that they are to be collected separately and recycled at end of life. The label on the battery may also  
include a chemical symbol for the metal concerned in the battery (Pb for lead, Hg for mercury, and Cd for  
cadmium). Users of batteries and accumulators must not dispose of batteries and accumulators as unsorted  
municipal waste, but use the collection framework available to customers for the return, recycling, and  
treatment of batteries and accumulators. Customer participation is important to minimize any potential  
effects of batteries and accumulators on the environment and human health due to the potential presence of  
hazardous substances. For proper collection and treatment, go to:  
http://www.lenovo.com/lenovo/environment  
Requirement for batteries containing perchlorate  
The following statement applies to users in the state of California, U.S.A.  
California Perchlorate Information:  
Products containing CR (manganese dioxide) lithium coin cell batteries may contain perchlorate.  
Perchlorate Material - special handling may apply, See http://www.dtsc.ca.gov/hazardouswaste/perchlorate  
The foregoing notice is provided in accordance with California Code of Regulations Title 22, Division 4.5  
Chapter 33. Best Management Practices for Perchlorate Materials. This product/part may include a lithium  
manganese dioxide battery which contains a perchlorate substance.  
Particulate contamination  
Attention: Airborne particulates (including metal flakes or particles) and reactive gases acting alone or in  
combination with other environmental factors such as humidity or temperature might pose a risk to the  
server that is described in this document. Risks that are posed by the presence of excessive particulate  
112 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
levels or concentrations of harmful gases include damage that might cause the server to malfunction or  
cease functioning altogether. This specification sets forth limits for particulates and gases that are intended  
to avoid such damage. The limits must not be viewed or used as definitive limits, because numerous  
other factors, such as temperature or moisture content of the air, can influence the impact of particulates  
or environmental corrosives and gaseous contaminant transfer. In the absence of specific limits that are  
set forth in this document, you must implement practices that maintain particulate and gas levels that are  
consistent with the protection of human health and safety. If Lenovo determines that the levels of particulates  
or gases in your environment have caused damage to the server, Lenovo may condition provision of repair  
or replacement of servers or parts on implementation of appropriate remedial measures to mitigate such  
environmental contamination. Implementation of such remedial measures is a customer responsibility.  
Table 44. Limits for particulates and gases  
Contaminant  
Limits  
Particulate  
• The room air must be continuously filtered with 40% atmospheric dust spot efficiency  
(MERV 9) according to ASHRAE Standard 52.21.  
• Air that enters a data center must be filtered to 99.97% efficiency or greater, using  
high-efficiency particulate air (HEPA) filters that meet MIL-STD-282.  
• The deliquescent relative humidity of the particulate contamination must be more than 60%2.  
• The room must be free of conductive contamination such as zinc whiskers.  
Gaseous  
• Copper: Class G1 as per ANSI/ISA 71.04-19853  
• Silver: Corrosion rate of less than 300 Å in 30 days  
1 ASHRAE 52.2-2008 - Method of Testing General Ventilation Air-Cleaning Devices for Removal Efficiency by Particle  
Size. Atlanta: American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.  
2 The deliquescent relative humidity of particulate contamination is the relative humidity at which the dust absorbs  
enough water to become wet and promote ionic conduction.  
3
ANSI/ISA-71.04-1985. Environmental conditions for process measurement and control systems: Airborne  
contaminants. Instrument Society of America, Research Triangle Park, North Carolina, U.S.A.  
Important information for the European Directive 2002/96/EC  
EU Only  
The Waste Electrical and Electronic Equipment (WEEE) mark applies only to countries within the European  
Union (EU) and Norway. Appliances are labeled in accordance with European Directive 2002/96/EC  
concerning waste electrical and electronic equipment (WEEE). The Directive determines the framework for  
the return and recycling of used appliances as applicable throughout the European Union. This label is  
applied to various products to indicate that the product is not to be thrown away, but rather reclaimed upon  
end of life per this Directive. Users of electrical and electronic equipment (EEE) with the WEEE marking per  
Annex IV of the WEEE Directive must not dispose of end of life EEE as unsorted municipal waste, but use the  
collection framework available to them for the return, recycle, recovery of WEEE and minimize any potential  
effects of EEE on the environment and human health due to the presence of hazardous substances. For  
additional WEEE information go to:  
http://www.lenovo.com/lenovo/environment  
Appendix C. Notices 113  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Le marquage des déchets d'équipements électriques et électroniques (DEEE) s'applique uniquement aux  
pays de l'Union européenne (EU) et à la Norvège. Les appareils sont marqués conformément à la Directive  
2002/96/CE du Conseil Européen relative aux déchets d'équipements électriques et électroniques (DEEE).  
Cette directive, applicable à l'ensemble des pays de l'Union européenne, concerne la collecte et le recyclage  
des appareils usagés. Ce marquage est apposé sur différents produits pour indiquer que ces derniers  
ne doivent pas être jetés, mais récupérés en fin de vie, conformément à cette directive. Les utilisateurs  
d'équipements électriques et électroniques portant le marquage DEEE, conformément à l'Annexe IV de la  
Directive DEEE, ne doivent pas mettre au rebut ces équipements comme des déchets municipaux non triés,  
mais ils doivent utiliser la structure de collecte mise à disposition des clients pour le retour, le recyclage et la  
récupération des déchets d'équipements électriques et électroniques, afin de réduire tout effet potentiel  
des équipements électriques et électroniques sur l'environnement et la santé en raison de la présence  
possible de substances dangereuses dans ces équipements. Pour plus d'informations sur les équipements  
électriques et électroniques, consultez le site http://www.lenovo.com/lenovo/environment.  
Die WEEE-Kennzeichnung gilt nur in Ländern der Europäischen Union und in Norwegen. Geräte werden  
gemäß der Richtlinie 2002/96/EC der Europäischen Union über Elektro- und Elektronikaltgeräte (WEEE)  
gekennzeichnet. Die Richtlinie regelt die Rückgabe und Wiederverwertung von Altgeräten innerhalb der  
Europäischen Union. Mit dieser Kennzeichnung versehene Altgeräte dürfen gemäß dieser Richtlinie  
nicht weggeworfen werden, sondern müssen zurückgegeben werden. Anwender von Elektro- und  
Elektronikgeräten mit der WEEE-Kennzeichnung dürfen diese gemäß Annex IV der WEEE-Richtlinie nach  
ihrem Gebrauch nicht als allgemeinen Hausmüll entsorgen. Stattdessen müssen diese Geräte im verfügbaren  
Sammelsystem zurückgegeben werden und damit einem Recycling- oder Wiederherstellungsprozess  
zugeführt werden, bei dem mögliche Auswirkungen der Geräte auf die Umwelt und den menschlichen  
Organismus aufgrund gefährlicher Substanzen minimiert werden. Weitere Informationen zur Entsorgung von  
Elektro- und Elektronikaltgeräten finden Sie unter der Adresse: http://www.lenovo.com/lenovo/environment.  
La marca de Residuos de equipos eléctricos y electrónicos (WEEE) se aplica sólo a los países pertenecientes  
a la Unión Europea (UE) y a Noruega. Los aparatos se etiquetan conforme a la Directiva Europea 2002/96/EC  
relativa a los residuos de equipos eléctricos y electrónicos (WEEE). La directiva determina el marco para  
devolver y reciclar los aparatos usados según sea aplicable en toda la Unión Europea. Esta etiqueta se  
aplica a varios productos para indicar que el producto no se va a desechar, sino que va ser reclamado por  
esta Directiva, una vez termine su ciclo de vida. Los usuarios de los equipos eléctricos y electrónicos (EEE)  
con la marca WEEE por el Anexo IV de la Directiva WEEE no deben tratar los EEE como desperdicios  
municipales no clasificados, una vez terminado su ciclo de vida, sino que deben utilizar el marco de recogida  
disponible para devolver, reciclar y recuperar los WEEE y minimizar los posibles efectos de los EEE en el  
medio ambiente y en la salud debidos a la presencia de substancias peligrosas. Para obtener información  
adicional acerca de WEEE consulte el sitio: http://www.lenovo.com/lenovo/environment.  
Il marchio WEEE (Waste Electrical and Electronic Equipment) viene applicato soltanto ai paesi all'interno  
dell'unione europea (EU) e norvegia. Le apparecchiature vengono etichettate in accordo con la direttiva  
europea 2002/96/EC riguardande lo smaltimento di apparecchiatura elettrica ed alettronica (WEEE). Le  
direttive determinano la procedura di restituzione e di riciclaggio delle apparecchiature usate in conformità  
con le normative dell'unione europea. Questa classificazione viene applicata a vari prodotti per indicare che  
il prodotto stesso non deve essere gettato ma riscattato al termine dell'utilizzo per quasta direttiva. Gli utenti  
di apparecchiature elettriche o elettroniche (EEE) marchiate WEEE secondo Annex IV della direttiva WEEE  
non devono disporre di fine utilizzo EEE come rifiuto, municipale non classificato, ma deve essere utilizzata  
la procedura di classificazione disponibile per il riscatto, riciclo, recupero del WEEE e minimizzare qualsiasi  
potenziale effetto della EEE sull'ambiente e sulla salute umana dovuto alla presenza di sostanze pericolose.  
Per ulteriori informazioni sulla WEEE visitare il sito: http://www.lenovo.com/lenovo/environment.  
A marca REEE (Resíduos de Equipamentos Eléctricos e Electrónicos) aplica-se apenas aos Estados  
Membros da União Europeia e à Noruega. Os aparelhos eléctricos deverão ser identificados em  
conformidade com a Directiva Europeia 2002/96/CE relativa a REEE (Resíduos de Equipamentos Eléctricos  
e Electrónicos). A Directiva determina o enquadramento normativo relativamente à devolução e reciclagem  
de aparelhos eléctricos utilizados, conforme aplicável no espaço da União Europeia. Esta etiqueta  
114 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
deverá ser aposta em diversos produtos para indicar que os mesmos não poderão ser deitados fora,  
mas sim recuperados no final da respectiva vida útil, de acordo com a referida Directiva. Os utilizadores  
de equipamentos eléctricos e electrónicos (EEE) com a marca REEE em conformidade com o Anexo IV da  
Directiva REEE não poderão deitar fora os EEE no final da respectiva vida útil como lixo municipal não  
separado, devendo sim utilizar a estrutura de recolha que lhes tenha sido disponibilizada para efeitos de  
devolução, reciclagem e recuperação de REEE, por forma a minimizar potenciais efeitos dos EEE sobre  
o ambiente e saúde pública resultantes da presença de substâncias perigosas. Para obter informações  
adicionais acerca da REEE consulte o sítio da web: http://www.lenovo.com/lenovo/environment.  
Het WEEE-merkteken (Waste Electrical and Electronic Equipment) geldt alleen voor landen binnen de  
Europese Unie (EU) en Noorwegen. Apparaten worden van een merkteken voorzien overeenkomstig  
Europese Richtlijn 2002/96/EC inzake afgedankte elektrische en elektronische apparatuur (waste electrical  
and electronic equipment, WEEE). Deze richtlijn bepaalt het raamwerk voor het retourneren en recyclen van  
gebruikte apparatuur, zoals van toepassing binnen de Europese Unie. Dit merkteken wordt aangebracht op  
diverse producten om aan te geven dat het product in kwestie niet dient te worden weggegooid, maar dat  
het aan het eind van de levenscyclus krachtens deze Richtlijn dient te worden geretourneerd. Gebruikers van  
elektrische en elektronische apparaten (EEE) welke zijn voorzien van het WEEE-merkteken zijn gehouden  
aan Annex IV van de WEEE Richtlijn en mogen gebruikte EEE niet weggooien als ongesorteerd afval, maar  
dienen gebruik te maken van het inzamelproces voor het teruggeven, recyclen en terugwinnen van WEEE  
dat voor hen beschikbaar is, en dienen de mogelijke effecten die EEE ten gevolge van de aanwezigheid van  
schadelijke stoffen kunnen hebben op het milieu en de volksgezondheid, tot een minimum te beperken. Voor  
meer informatie over WEEE gaat u naar: http://www.lenovo.com/lenovo/environment.  
WEEE-mærkningen (Waste Electrical and Electronic Equipment) gælder kun for lande i EU samt Norge.  
Udstyr mærkes i henhold til EU's direktiv 2002/96/EF om affald af elektrisk og elektronisk udstyr (WEEE).  
Direktivet fastlægger de rammer, der gælder for returnering og genbrug af brugt udstyr i EU. Mærkaten  
påsættes forskellige produkter for at angive, at produktet ikke må smides væk, når det er udtjent, men skal  
genvindes i henhold til dette direktiv. Brugere af elektrisk og elektronisk udstyr (EEE), der er mærket med  
WEEE-mærket som angivet i Bilag IV til WEEE-direktivet, må ikke bortskaffe brugt EEE som usorteret  
husholdningsaffald, men skal bruge den indsamlingsordning, der er etableret, så WEEE kan returneres,  
genbruges eller genvindes. Formålet er at minimere den eventuelle påvirkning af miljøet og menneskers  
sundhed som følge af tilstedeværelsen af skadelige stoffer. Der er flere oplysninger om affald af elektrisk og  
elektronisk udstyr på adressen http://www.lenovo.com/lenovo/environment.  
Sähkö- ja elektroniikkalaiteromu (Waste electrical and electronic equipment, WEEE) -merkintä koskee vain  
Euroopan unionin (EU) jäsenmaita ja Norjaa. Sähkö- ja elektroniikkalaitteet merkitään Euroopan parlamentin  
ja neuvoston direktiivin 2002/96/EY mukaisesti. Kyseinen direktiivi määrittää Euroopan Unionin alueella  
käytössä olevat palautus- ja kierrätyskäytännöt. WEEE-merkintä laitteessa osoittaa, että direktiivin ohjeiden  
mukaan tuotetta ei tulisi hävittää sen elinkaaren päässä, vaan se tulee toimittaa uusiokäyttöön. Käyttäjien,  
joiden sähkö- ja elektroniikkalaitteissa on tämä sähkö- ja elektroniikkalaiteromun direktiivin liitteen IV  
mukainen merkintä, tulee kierrättää kyseiset laitteet käytettävissä olevien resurssien mukaan ja varmistaa,  
että niistä tai niissä käytetyistä materiaaleista ei aiheudu haittaa ympäristölle tai ihmisten terveydelle. Sähkö-  
ja elektroniikkalaitteita ei saa hävittää sekajätteen mukana. Lisätietoja sähkö- ja elektroniikkalaiteromun  
uusiokäytöstä on WWW-sivustossa http://www.lenovo.com/lenovo/environment.  
WEEE-merket (Waste Electrical and Electronic Equipment) gjelder bare for land i Den europeiske union  
(EU) og Norge. Utstyr merkes i henhold til EU-direktiv 2002/96/EF om avfall fra elektrisk og elektronisk  
utstyr (WEEE). Direktivet fastsetter rammene for retur og resirkulering av brukt utstyr innenfor EU. Dette  
merket benyttes på forskjellige produkter for å angi at produktet ikke må kastes, men må behandles i  
henhold til dette direktivet ved slutten av produktets levetid. Brukere av elektrisk og elektronisk utstyr  
(EEE) som er merket med WEEE-merket ifølge vedlegg IV i WEEE-direktivet, må ikke kaste utstyret som  
usortert husholdningsavfall, men må bruke de tilgjengelige innsamlingssystemene for retur, resirkulering og  
gjenvinning av kassert elektrisk og elektronisk utstyr for å redusere en eventuell skadelig virkning av elektrisk  
og elektronisk utstyr på miljø og helse, som skyldes skadelige stoffer. Du finner mer informasjon om WEEE  
på denne adressen: http://www.lenovo.com/lenovo/environment.  
Appendix C. Notices 115  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Restriction of Hazardous Substances Directive (RoHS)  
This topic provides statements about the Restriction of Hazardous Substances Directive (RoHS).  
116 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
China RoHS  
Turkish statement of compliance  
The Lenovo product meets the requirements of the Republic of Turkey Directive on the Restriction of the Use  
of Certain Hazardous Substances in Electrical and Electronic Equipment (EEE).  
Appendix C. Notices 117  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Ukraine RoHS  
German Ordinance for Work gloss statement  
The product is not suitable for use with visual display work place devices according to clause 2 of the  
German Ordinance for Work with Visual Display Units.  
Das Produkt ist nicht für den Einsatz an Bildschirmarbeitsplätzen im Sinne § 2 der  
Bildschirmarbeitsverordnung geeignet.  
Electronic emission notices  
This topic includes electronic emission notices.  
Federal Communications Commission (FCC) Statement  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant  
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with the instructions, may cause harmful interference  
to radio communications. However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by  
one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
• Consult an authorized dealer or service representative for help.  
Lenovo is not responsible for any radio or television interference caused by using other than specified or  
recommended cables and connectors or by unauthorized changes or modifications to this equipment.  
Unauthorized changes or modifications could void the user's authority to operate the equipment.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)  
this device may not cause harmful interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
Industry Canada Class B emission compliance statement  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
European Union - Compliance to the Electromagnetic Compatibility Directive  
118 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the  
approximation of the laws of the Member States relating to electromagnetic compatibility. Lenovo cannot  
accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended  
modification of the product, including the installation of option cards from other manufacturers.  
This product has been tested and found to comply with the limits for Class B Information Technology  
Equipment according to European Standard EN 55022. The limits for Class B equipment were derived  
for typical residential environments to provide reasonable protection against interference with licensed  
communication devices.  
German Class B compliance statement  
Deutschsprachiger EU Hinweis:  
Hinweis für Geräte der Klasse B EU-Richtlinie zur Elektromagnetischen Verträglichkeit  
Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG (früher 89/336/EWG) zur  
Angleichung der Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU-Mitgliedsstaaten  
und hält die Grenzwerte der EN 55022 Klasse B ein.  
Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu  
betreiben. Des Weiteren dürfen auch nur von der Lenovo empfohlene Kabel angeschlossen werden.  
Lenovo übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt  
ohne Zustimmung der Lenovo verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohne  
Empfehlung der Lenovo gesteckt/eingebaut werden.  
Deutschland:  
Einhaltung des Gesetzes über die elektromagnetische Verträglichkeit von Betriebsmitteln  
Dieses Produkt entspricht dem „Gesetz über die elektromagnetische Verträglichkeit von Betriebsmitteln“  
EMVG (früher „Gesetz über die elektromagnetische Verträglichkeit von Geräten“). Dies ist die Umsetzung der  
EU-Richtlinie 2004/108/EG (früher 89/336/EWG) in der Bundesrepublik Deutschland.  
Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit  
von Betriebsmitteln, EMVG vom 20. Juli 2007 (früher Gesetz über die elektromagnetische  
Verträglichkeit von Geräten), bzw. der EMV EG Richtlinie 2004/108/EC (früher 89/336/EWG), für  
Geräte der Klasse B.  
Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen  
- CE - zu führen. Verantwortlich für die Konformitätserklärung nach Paragraf 5 des EMVG ist die Lenovo  
(Deutschland) GmbH, Gropiusplatz 10, D-70563 Stuttgart.  
Informationen in Hinsicht EMVG Paragraf 4 Abs. (1) 4:  
Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse B.  
Korea Class B compliance statement  
Appendix C. Notices 119  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Japan VCCI Class B compliance statement  
Japan compliance statement for products which connect to the power mains with rated current  
less than or equal to 20 A per phase  
Lenovo product service information for Taiwan  
120 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
A
Ethernet connector 25  
exiting, Setup Utility 99  
expansion 10  
Administrator, password 97  
audio line-in connector 25  
audio line-out connector 25  
availability 11  
F
failure, recovering from POST/BIOS 104  
B
features  
9
field replaceable units (FRUs) 69  
firmware, updating 101  
flashing the BIOS 103  
basic guidelines 29  
basic troubleshooting 15  
boot-block recovery 104  
front bezel  
front bezel, removing 34, 54  
front bezel, reinstalling 34, 54  
front connectors 23  
C
cables  
front fan assembly, replacing 55  
rear connectors 67  
changing  
password 97  
G
startup device sequence 99  
CMOS, clearing 98  
components, internal 27  
configuration  
gaseous contamination 112  
German gloss statement 118  
updating server 83  
connectivity 10  
connector 25  
H
hard disk drive, replacing 43  
heat sink and fan assembly, replacing 52  
help  
cables 67  
connectors  
front 23  
rear 24  
and service 107  
considerations, passwords 97  
contamination, particulate and gaseous 112  
CRU  
completing the installation 66  
customer replaceable units (CRUs) 69  
customer support center 107  
I
information  
resources 105  
safety 105  
warranty 105  
Input/Output (I/O) features 10  
installing  
D
device drivers 68  
Ethernet card 38  
installing options  
memory module 39  
PCI card 35  
deleting a password 97  
Description 25  
device drivers  
installing 68  
devices, handling static-sensitive 30  
diagnostics programs, using 107  
DisplayPort connector 25  
documentation, using 107  
integrated functions 11  
internal drives 10  
L
E
locating components 27  
EasyStartup  
using 102  
environment, operating 11  
Ethernet card  
M
memory 10  
installing 38  
memory module  
© Copyright Lenovo 2011  
121  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
installing, removing 39  
system board 39  
Microphone connector 25  
microprocessor  
replacing 59  
specifications 10  
S
safety information 105  
security  
enabling or disabling 98  
selecting  
startup device 99  
temporary startup device 99  
serial port 25  
N
server  
notices 109  
turn off 67  
turn on 67  
server configuration, updating 83  
server cover  
removing 33  
O
optical drive, replacing 41  
server cover, reinstalling 66  
server replaceable units 69  
service  
P
and help 107  
particulate contamination 112  
parts listing 69  
customer support center 107  
serviceability 11  
services  
other 108  
purchasing additional 108  
setting  
password 97  
settings  
changing 96  
viewing 96  
parts replacement, completing 66  
password  
Administrator 97  
considerations 97  
Power-On Password 97  
setting, changing, deleting 97  
passwords  
erasing 98  
lost or forgotten 98  
Setup Utility 83  
Setup Utility program, starting 83  
Setup Utility, exiting 99  
size 11  
passwords, using 96  
PCI card 35  
installing, replacing 35  
slots 35  
specifications  
9
power cords 76  
power supply 10  
starting the Setup Utility program 83  
startup device 99  
sequence, changing 99  
temporary, selecting 99  
static-sensitive devices, handling 30  
system  
power supply assembly, replacing 50  
power-on self-test (POST) 102  
Power-On, Password 97  
problem isolation tables 16  
programs, updating system 102  
purchasing additional services 108  
programs 102  
system board  
locating parts 26  
locations 26  
R
memory module 39  
system board battery  
replacing 62  
RAS features 11  
rear connectors 24  
rear fan assembly, replacing 57  
recovering  
system reliability guidelines 30  
from a POST/BIOS update failure 104  
recovery  
boot-block 104  
T
temporary startup device 99  
the BIOS, updating (flashing) 103  
trademarks 110  
troubleshooting, basic 15  
turn off  
server 67  
turn on  
server 67  
TÜV gloss statement 118  
reliability 11  
removing server cover 33  
replacement parts 69  
replacing  
hard disk drive 43  
heat sink and fan assembly 52  
microprocessor 59  
system board battery 62  
resources, information 105  
122 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
U
updating  
(flashing) the BIOS 103  
server configuration 83  
system programs 102  
updating (flashing) the BIOS 103  
updating firmware 101  
USB connector 25  
using  
diagnostic programs 107  
documentation 107  
EasyStartup 102  
other services 108  
passwords 96  
Setup Utility 83  
V
VGA monitor connector 25  
video subsystem 10  
viewing and changing settings 96  
W
warranty information 105  
Web site  
Lenovo support 29, 69  
working inside the server with the power on 31  
© Copyright Lenovo 2011  
123  
Download from Www.Somanuals.com. All Manuals Search And Download.  
124 ThinkServer TS130 Hardware Maintenance Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

KWC Indoor Furnishings K26VB02700 User Manual
Kyocera Cell Phone KE433 User Manual
Kyocera Cell Phone KX414 User Manual
Land Pride Lawn Mower FM20 Series User Manual
LG Electronics Cell Phone UX220 User Manual
Lincoln Electric Welder SVM154 A User Manual
Lincoln Electric Welder V205 T User Manual
Link electronic Stereo Amplifier PRC 970 User Manual
Martin Audio Speaker C101C User Manual
Melissa Styling Iron 635 120 User Manual