Hardware Maintenance Manual
ThinkPad Edge 13″, E30, and E31
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Sleep mode .
Hibernation mode
Numeric error codes
34
34
35
35
37
37
38
38
39
General safety .
1
1
3
Electrical safety .
Error messages
No-beep symptoms .
Safety inspection guide .
discharge.
3
4
4
Grounding requirements .
Safety notices (multilingual translations) .
19
20
board
20
20
Retaining serial numbers.
45
46
GAV .
20
20
unit
46
47
47
FRU identification for CTO, CMV, and GAV
products .
21
What to do first
23
24
24
27
27
28
28
29
29
30
1030 DIMM . .
50
50
52
53
54
55
57
Diagnostics using PC-Doctor for DOS.
FRU tests .
Checking the AC adapter.
Checking operational charging
module
59
62
63
64
66
1090 Backup battery .
1110 Speaker assembly .
Restoring the factory contents by using Recovery
Disc Set .
31
32
32
32
33
33
33
34
34
cable
73
75
78
80
81
82
84
Passwords .
1140 LCD unit .
Power management
© Copyright Lenovo 2009, 2011
i
Download from Www.Somanuals.com. All Manuals Search And Download.
About this manual
This manual contains service and reference information for the following ThinkPad® products.
ThinkPad Edge 13”
MT 0196, 0197, 0217, 0221, 0250 and 0492
ThinkPad Edge E30 and E31
MT 0196 and 0250
Use this manual along with the advanced diagnostic tests to troubleshoot problems.
Important: This manual is intended only for trained service technicians who are familiar with ThinkPad
products. Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively.
Before servicing a ThinkPad product, be sure to read all the information under Chapter 1 “Safety information”
on page 1.
© Copyright Lenovo 2009, 2011
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Safety information
This chapter presents following safety information that you need to be familiar with before you service
a ThinkPad Notebook.
•
•
•
•
•
•
General safety
Follow these rules to ensure general safety:
• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that
you think is too heavy for you.
• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
• Before you start the machine, make sure that other service technicians and the customer's personnel are
not in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing
the machine.
• Keep your toolcase away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your
sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, about 8
centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing.
Attention: Metal objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device
that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan
louvers or cover them with labels or stickers.
Electrical safety
Observe the following rules when working on electrical equipment.
© Copyright Lenovo 2009, 2011
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important:
Use only approved tools and test equipment. Some hand tools have handles covered with a soft material
that does not insulate you when working with live electrical currents.
Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to
decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical
accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.
Attention: Another person must be there to switch off the power, if necessary.
– Use only one hand when working with powered-on electrical equipment; keep the other hand in your
pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete circuit. By observing the above
rule, you may prevent a current from passing through your body.
– When using testers, set the controls correctly and use the approved probe leads and accessories for
that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as
metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages; Instructions for these
precautions are in the safety sections of maintenance information. Use extreme care when measuring
high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.
• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
nongrounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on when they are removed from their normal operating
places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
– Similar units to listed above
This practice ensures correct grounding of the units.
• If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
2
Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each
machine was designed and built, required safety items were installed to protect users and service technicians
from injury. This guide addresses only those items. You should use good judgment to identify potential
safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock)
• Explosive hazards, such as a damaged CRT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware
To determine whether there are any potentially unsafe conditions, use the following checklist at the beginning
of every service task. Begin the checks with the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground
continuity for 0.1 ohm or less between the external ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-ThinkPad alterations. Use good judgment as to the safety of any
non-ThinkPad alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts:
Chapter 1. Safety information
Download from Www.Somanuals.com. All Manuals Search And Download.
3
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when
handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.
Note:
The use of a grounding system to guard against ESD damage is desirable but not necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
– When working on a double-insulated or battery-operated system, use an ESD common ground or
reference point. You can use coax or connector-outside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a certified electrician.
Safety notices (multilingual translations)
The safety notices in this section are provided in the following languages:
• English
• Arabic
• German
• Hebrew
• Japanese
• Korean
• Spanish
DANGER
DANGER
4
Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
DANGER
DANGER
DANGER
DANGER
DANGER
Chapter 1. Safety information
Download from Www.Somanuals.com. All Manuals Search And Download.
5
DANGER
DANGER
DANGER
DANGER
DANGER
Chapter 1. Safety information
Download from Www.Somanuals.com. All Manuals Search And Download.
9
VORSICHT
VORSICHT
VORSICHT
VORSICHT
VORSICHT
Chapter 1. Safety information 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Safety information 17
Download from Www.Somanuals.com. All Manuals Search And Download.
18 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Important service information
This chapter presents following important service information that applies to all machine types supported by
this manual:
•
–
–
–
•
–
–
Important:
Advise customers to contact the Lenovo Customer Support Center if they need any assistance in
obtaining or installing any software fixes, drivers, and BIOS downloads. Telephone numbers for Lenovo
Support are available at:
System Disassembly/Reassembly videos that show the FRU removals or replacements for the Lenovo®
authorized service technicians are available in the following support site:
Strategy for replacing FRUs
Before replacing parts:
Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs
listed in this manual.
After a system board is replaced, ensure that the latest BIOS is loaded to the system board before
completing the service action.
To download software fixes, drivers, and BIOS, do as follows:
1. Go to http://support.lenovo.com.
2. Enter the product number of the computer or press Auto-detect button on the screen.
3. Select Downloads and drivers.
4. Follow the directions on the screen and install the necessary software.
Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs:
• If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall
the original FRU before you continue.
• Some computers have both a processor board and a system board. If you are instructed to replace either
the processor board or the system board, and replacing one of them does not correct the problem,
reinstall that board, and then replace the other one.
• If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error.
Before replacing the adapter or device, remove the FRUs, one by one, to see if the symptoms change.
Replace only the FRU that changed the symptoms.
Attention: The setup configuration on the computer you are servicing may have been customized. Running
Automatic Configuration may alter the settings. Note the current configuration settings (using the View
Configuration option); then, when service has been completed, verify that those settings remain in effect.
© Copyright Lenovo 2009, 2011
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Strategy for replacing a hard disk drive
Always try to run a low-level format before replacing a hard disk drive. This will cause all customer data on
the hard disk to be lost. Be sure that the customer has a current backup of the data before doing this task.
Attention: The drive startup sequence in the computer you are servicing may have been changed. Be
extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect
drive, data or programs can be overwritten.
Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper handling of a system board can
cause damage to those components, and may cause a system malfunction.
Attention: When handling a system board:
• Do not drop a system board or apply any excessive force to it.
• Avoid rough handling of any kind.
• Avoid bending a system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset.
How to use error message
Use the error codes displayed on the screen to diagnose failures. If more than one error code is displayed,
begin the diagnosis with the first error code. Whatever causes the first error code may also cause false error
codes. If no error code is displayed, see whether the error symptom is listed in the Symptom-to-FRU
Index for the computer you are servicing.
Strategy for replacing FRUs for CTO, CMV, and GAV
Product definition
Dynamic Configure To Order (CTO)
This provides the ability for a customer to configure a Lenovo solution from an eSite, and have this
configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label,
Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT
and 3-digit model, where model = “CTO” (Example: 1829-CTO).
Custom Model Variant (CMV)
This is a unique configuration that has been negotiated between Lenovo and the customer. A unique 4-digit
MT and 3-digit model is provided to the customer to place orders (Example: 1829-W15). A CMV is a special
bid offering. Therefore, it is NOT generally announced.
• The MTM portion of the machine label is the 4-digit MT and 3-digit model, where model = “CTO”
(Example: 1829-CTO). The PRODUCT ID portion of the machine label is the 4-digit MT and 3-digit CMV
model (Example: 1829-W15).
• The PEW record is the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
• eSupport will show both the CTO and CMV machine type models (Example: 1829-CTO and 1829-W15
will be found on the eSupport site.)
• The HMM will have the 4-digit MT and 3-digit CTO model only (Example: 1829-CTO). Again, CMVs are
custom models and are not found in the HMM.
General Announce Variant (GAV)
This is a standard model (fixed configuration). GAVs are announced and offered to all customers. The MTM
portion of the machine label is a 4-digit MT and 3-digit model, where model = a “fixed part number”, not
20 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
“CTO” (Example: 1829-F1U). Also, PEW, eSupport, and the HMM will list these products under the same
fixed model number.
FRU identification for CTO, CMV, and GAV products
There are three information resources to identify which FRUs are used to support CTO, CMV, and GAV
products. These sources are PEW, eSupport, and the HMM.
Using PEW
• PEW is the primary source for identifying FRU part numbers and FRU descriptions for the key commodities
for CTO, CMV and GAV products at a MT - serial number level. An example of key commodities are hard
disk drives, system boards, microprocessors, Liquid Crystal Displays (LCDs), and memory.
• Remember, all CTO and CMV products are loaded in PEW under the 4-digit MT and 3-digit model, where
model = “CTO” (Example: 1829-CTO). GAVs are loaded in PEW under the 4-digit MT and 3-digit model,
where model = a “fixed part number”, not “CTO” (Example: 1829-F1U).
• PEW can be accessed at the following Web site:
Select Warranty lookup. Input the MT and the Serial number and the list of key commodities will be
returned in the PEW record under COMPONENT INFORMATION.
Using eSupport
For key commodities (examples - hard disk drive, system board, microprocessor, LCD, and memory)
• eSupport can be used to view the list of key commodities built in a particular machine serial (this is the
same record found in PEW).
• eSupport can be accessed at the following Web site:
http://support.lenovo.com
• To view the key commodities, do the following:
1. Click Products & Service Warranty.
2. Click Check Warranty Status.
3. On the Warranty Status Lookup page, click Parts Lookup.
4. Type your machine type and serial number, and then click Submit. The key commodities will be
displayed.
For the remaining FRUs (the complete list of FRUs at the MT model level)
• eSupport can be used to view the complete list of FRUs for a machine type and model.
• To view the complete list of FRUs, do the following:
1. Click Product & Parts Detail and then follow the instructions on the screen to reach the Product
and Parts Details page.
2. Click the Parts Detail tab to view the list of service parts.
Using the HMM
For key commodities (examples - hard disk drive, system board, microprocessor, LCD, and memory)
Use the HMM as a backup to PEW and eSupport to view the complete list of FRUs at the MT model level.
Chapter 2. Important service information 21
Download from Www.Somanuals.com. All Manuals Search And Download.
22 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. General checkout
This chapter presents following information:
•
•
–
–
–
•
The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS
diagnostics program. Some descriptions might not apply to your particular computer.
Before you go to the checkout guide, be sure to read the following important notes.
Important:
• Only certified trained personnel should service the computer.
• Before replacing any FRU, read the entire page on removing and replacing FRUs.
• When you replace FRUs, use new nylon-coated screws.
• Be extremely careful during such write operations as copying, saving, or formatting. Drives in the
computer that you are servicing sequence might have been altered. If you select an incorrect drive,
data or programs might be overwritten.
• Replace a FRU only with another FRU of the correct model. When you replace a FRU, make sure that
the model of the machine and the FRU part number are correct by referring to the FRU parts list.
• A FRU should not be replaced because of a single, unreproducible failure. Single failures can occur
for a variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation,
electrostatic discharge, or software errors. Consider replacing a FRU only when a problem recurs. If you
suspect that a FRU is defective, clear the error log and run the test again. If the error does not recur, do
not replace the FRU.
• Be careful not to replace a nondefective FRU.
What to do first
When you do return a FRU, you must include the following information in the parts exchange form or
parts return form that you attach to it:
• Name and phone number of service technician
• Date of service
• Date on which the machine failed
• Date of purchase
• Failure symptoms, error codes appearing on the display, and beep symptoms
• Procedure index and page number in which the failing FRU was detected
• Failing FRU name and part number
• Machine type, model number, and serial number
• Customer's name and address
Note: During the warranty period, the customer may be responsible for repair costs if the computer damage
was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper
maintenance by the customer. Following is a list of some common items that are not covered under warranty
and some symptoms that might indicate that the system was subjected to stress beyond normal use.
© Copyright Lenovo 2009, 2011
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Before checking problems with the computer, determine whether the damage is covered under the warranty
by referring to the following list:
The following are not covered under warranty:
• LCD panel cracked from the application of excessive force or from being dropped
• Scratched (cosmetic) parts
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force
• Damage caused by liquid spilled into the system
• Damage caused by the improper insertion of a PC Card or the installation of an incompatible card
• Improper disc insertion or use of an optical drive
• Diskette drive damage caused by pressure on the diskette drive cover, foreign material in the drive,
or the insertion of a diskette with multiple labels
• Damaged or bent diskette eject button
• Fuses blown by attachment of a nonsupported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect AC adapter on laptop products
The following symptoms might indicate damage caused by nonwarranted activities:
• Missing parts might be a symptom of unauthorized service or modification.
• If the spindle of a hard disk drive becomes noisy, it may have been subjected to excessive force,
or dropped.
Checkout guide
Use the following procedures as a guide in identifying and correcting problems with the ThinkPad Notebook.
Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products,
prototype cards, or modified options can lead to false indications of errors and invalid system responses.
1. Identify the failing symptoms in as much detail as possible.
2. Verify the symptoms. Try to re-create the failure by running the diagnostic test or by repeating the
operation.
Diagnostics using PC-Doctor for DOS
The ThinkPad Notebook has a test program called PC-Doctor for DOS (hereafter called PC-Doctor.) You can
detect errors by running the diagnostics test included in PC-Doctor.
Note: PC-Doctor for DOS is available at the following Web site:
http://support.lenovo.com
To create the PC-Doctor diagnostic CD, follow the instructions on the Web site.
For some possible configurations of the computer, PC-Doctor might not run correctly. To avoid this problem,
you need to initialize the computer setup by use of the BIOS Setup Utility before you run PC-Doctor.
To enter BIOS Setup Utility, do as follows:
1. Turn on the computer.
2. When the ThinkPad logo comes up, immediately press F1 to enter the BIOS Setup Utility.
Note: If a supervisor password has been set by the customer, BIOS Setup Utility menu appears after the
password is entered. You can start the BIOS Setup Utility by pressing Enter instead of entering the supervisor
password; however, you cannot change the parameters that are protected by the supervisor password.
24 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
On the BIOS Setup Utility screen, press F9, Enter, F10, and then Enter.
Note: When you initialize the computer configuration, some devices are disabled, such as the serial port. If
you test one of these devices, you will need to enable it by using Configuration utility for DOS. The utility is
available on the following Web site:
http://support.lenovo.com
Testing the computer
In this product, you need an external optical drive to use the PC-Doctor diagnostic CD to test the hardware
features.
Note: The PC-Doctor for DOS CD-R/CD-RW disc supports only test of optical disc drives (CD-RW,
CD-RW/DVD Combo, and DVD Multi drives) on ThinkPad computers. It does not support test of any optical
disc drives connected through USB devices, PC cards, CardBus cards, or similar. The USB limitation only
applies to testing of the device. Using a bootable PC-Doctor for DOS CD/DVD, the system can be started
from a USB attached optical drive.
To run the test, do as follows:
1. Turn off the computer.
2. Make sure that the optical drive that is supported as a startup device is installed on the computer
you are servicing.
page 28, and check the power sources.
4. When the ThinkPad logo comes up, immediately press F12 to enter the Boot Menu.
5. Insert the PC-Doctor CD into the optical drive.
6. Press cursor keys to select ATAPI CDx (x: 0, 1, ...) and then press Enter.
7. Follow the instructions on the screen.
8. The main panel of PC-Doctor appears.
9. Select Diagnostics with the arrow keys, and press Enter.
Note: You can select an item not only with the arrow keys, but also with the TrackPoint® pointer.
Instead of pressing Enter, click the left button.
A pull-down menu appears. (Its exact form depends on the model.)
Note: PC-Doctor menu does not mean the formal support device list. Some unsupported device names
may appear in the PC-Doctor menu.
Diagnostics
Interactive Tests
Hardware Info
Utility
Quit
F1=Help
Run Normal Test
Run Quick Test
CPU/Coprocessor
Systemboard
Video Adapter
Fixed Disks
Diskette Drives
Other Devices
Wireless LAN
Advanced Memory Tests
PC-DOCTOR 2.0 Copyright 2008 PC-Doctor, Inc. All Rights Reserved.
Use the cursor keys and ESC to move in menus. Press ENTER to select.
The options on the test menu are as follows:
Chapter 3. General checkout 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostics
Interactive Tests
• Run Normal Test
• Run Quick Test
• CPU/Coprocessor
• System board
• Video Adapter
• Fixed Disks
• Diskette Drives
• Other Devices
• Wireless LAN
• Keyboard
• Video
• Internal Speaker
• Mouse
• Diskette
• System Load
• Optical Drive Test
• Intel WLAN Radio Test
• Advanced Memory Tests
Notes:
• In the Keyboard test in Interactive Tests, the Fn key should be held down for at least 2 seconds; otherwise, it
cannot be sensed.
• Video Adapter test supports only the LCD display on the ThinkPad Notebook. If you have an external monitor
attached to your computer, detach it before running PC-Doctor for DOS.
• To test Digital Signature Chip, the security chip must be set to Active.
10. Run the applicable function test.
11. Follow the instructions on the screen. If there is a problem, PC-Doctor shows messages describing it.
12. To exit the test, select Quit — Exit Diag. To cancel the test, press Esc.
Note: After running PC-Doctor, check the time and date on the system and reset them if they are incorrect.
Detecting system information with PC-Doctor
PC-Doctor can detect the following system information:
Hardware Info
• System Configuration
• Memory Contents
• Physical Disk Drives
• Logical Disk Drives
• VGA Information
• IDE Drive Info
• PCI Information
• PNPISA Info
• SMBIOS Info
• VESA LCD Info
• Hardware Events Log
Utility
• Run External Tests
• Surface Scan Hard Disk
• Benchmark System
• DOS Shell
• Tech Support Form
• Battery Rundown
• View Test Log
• Print Log
• Save Log
• Full Erase Hard Drive
• Quick Erase Hard Drive
26 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Lenovo ThinkVantage Toolbox
Lenovo ThinkVantage® Toolbox is a diagnostic program that works through the Windows operating system.
It enables you to view symptoms of computer problems and solutions for them, and includes automatic
notification when action is required, computing assistance, advanced diagnostics, and diagnostic history.
Note:
The latest Lenovo ThinkVantage Toolbox is available at the following Web site:
http://support.lenovo.com
To install the latest Lenovo ThinkVantage Toolbox on the computer, follow the instructions on the Web site.
To run this program, do as follows:
Click Start ➙ Control Panel ➙ System and Security ➙ Lenovo's System Health and Diagnostics
Follow the instructions on the screen. Lenovo ThinkVantage Toolbox also has problem determination aids
that determine software and usage problems.
For additional information about this program, see the Help for the program.
FRU tests
The following table shows the test for each FRU.
Table 1. FRU tests
FRU
Applicable test
System board
1. Diagnostics ➙ CPU/Coprocessor
2. Diagnostics ➙ Systemboard
Power
Diagnostics ➙ ThinkPadDevices ➙ AC Adapter, Battery 1 (Battery2)
1. Diagnostics ➙ Video Adapter
2. Interactive Tests ➙ Video
LCD unit
Audio
Enter the BIOS Setup Utility and change Serial ATA (SATA) setting to Compatibility,
and run Diagnostics ➙ Other Device ➙ Conexant Audio
Speaker
Interactive Tests ➙ Internal Speaker
Note: Once Audio test is done, the no sound is heard this test. In this case, turn off
and turn on the computer. Then, run this test again.
Keyboard
1. Diagnostics ➙ Systemboard ➙ Keyboard
2. Interactive Tests ➙ Keyboard
Hard disk drive or solid state
drive
Enter the BIOS Setup Utility and change Serial ATA (SATA) setting to Compatibility,
and run Diagnostics ➙ Fixed Disks
You can also diagnose the drive without starting up the operating system. To diagnose
the drive from the BIOS Setup Utility, do as follows:
1. Remove any diskette from the diskette drive, and then turn off the computer.
2. Turn on the computer.
3. While the message, “To interrupt normal startup, press Enter,” is displayed at the
lower left of the screen, press F1 to enter the BIOS Setup Utility.
4. Using cursor keys, select HDD diagnostic program. Press enter.
5. Using cursor keys, select Main hard disk drive.
6. Press Enter to start the diagnostic program.
Diskette drive
1. Diagnostics ➙ Diskette Drives
2. Interactive Tests ➙ Diskette
Chapter 3. General checkout 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 1. FRU tests (continued)
FRU
Applicable test
Memory
1. If two DIMMs are installed, remove one of them and run Diagnostics ➙ Advanced
Memory Tests.
2. If the problem does not recur, return the DIMM to its place, remove the other one,
and run the test again.
TrackPoint or pointing
device
If the TrackPoint does not work, check the configuration as specified in the BIOS Setup
Utility. If the TrackPoint is disabled, select Automatic to enable it.
After you use the TrackPoint, the pointer may drift on the screen for a short time. This
drift can occur when a slight, steady pressure is applied to the TrackPoint pointer.
This symptom is not a hardware problem. If the pointer stops after a short time, no
service action is necessary.
If enabling the TrackPoint does not correct the problem, continue with the following:
• Interactive Tests ➙ Mouse
Touch Pad
If the Touch Pad does not work, check the configuration as specified in the BIOS Setup
Utility. If the Touch Pad is disabled, select Automatic to enable it. If enabling the Touch
Pad does not correct the problem, continue with the following:
• Interactive Tests ➙ Mouse
Power system checkout
To verify a symptom, do the following:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the AC adapter.
4. Check that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the AC adapter and install the charged battery pack.
7. Check that the battery pack supplies power when you turn on the computer.
If you suspect a power problem, see the appropriate one of the following power supply checkouts:
•
•
•
•
Checking the AC adapter
You are here because the computer fails only when the AC adapter is used.
• If the power-on indicator does not turn on, check the power cord of the AC adapter for correct continuity
and installation.
• If the computer does not charge during operation, go to “Checking operational charging” on page 29.
To check the AC adapter, do the following:
1. Unplug the AC adapter cable from the computer.
2. Measure the output voltage at the plug of the AC adapter cable. See the following figure:
28 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Pin
1
Voltage (V dc)
+20
0
3
2
2
3
Ground
1
(20V)
Note: Output voltage of pin no.2 of the AC adapter may different from the one you are servicing.
3. If the voltage is not correct, replace the AC adapter.
4. If the voltage is acceptable, do the following:
• Replace the system board.
Note: Noise from the AC adapter does not always indicate a defect.
Checking operational charging
To check whether the battery charges properly during operation, use a discharged battery pack or a battery
pack that has less than 50% of the total power remaining when installed in the computer.
Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery
pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does
not turn on, replace the battery pack.
If the charge indicator still does not turn on, replace the system board. Then reinstall the battery pack. If it is
still not charged, go to the next section.
Checking the battery pack
Battery charging does not start until the Power Manager Battery Gauge shows that less than 96% of the
total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects
the battery pack from being overcharged or from having a shortened life.
To check your battery, move your cursor to the Power Manager Battery Gauge icon in the icon tray of the
Windows taskbar and wait for a moment (but do not click), and the percentage of battery power remaining
is displayed. To get detailed information about the battery, double-click the Power Manager Battery
Gauge icon.
Note: If the battery pack becomes hot, it may not be able to charge. Remove it from the computer and leave
it at room temperature for a while. After it cools down, reinstall and recharge it.
To check the battery pack, do the following:
1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1 (+) and 7 (-). See the
following figure:
Note: ThinkVantage Toolbox through the "System Health" or through Diagnostics" features will
proactively determine if the replacement of battery pack is required. A "POOR" condition indicates
battery replacement is required for proper operation.
Chapter 3. General checkout 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminal
Voltage (V dc)
+ 0 to + 12.6
Ground (-)
1
7
7(-)
6(-)
5
4
3
2(+)
1(+)
3. If the voltage is less than +11.0 V dc, the battery pack has been discharged.
Note: Recharging will take at least 3 hours, even if the indicator does not turn on.
If the voltage is still less than +11.0 V dc after recharging, replace the battery.
4. If the voltage is more than +11.0 V dc, measure the resistance between battery terminals 5 and 7.
The resistance must be 4 to 30 K Ω. If the resistance is not correct, replace the battery pack. If the
resistance is correct, replace the system board.
Checking the backup battery
Do the following:
1. Power off the computer, and unplug the AC adapter from it.
2. Turn the computer upside down.
5. Measure the voltage of the backup battery. See the following figure.
Wire
Red
Voltage (V dc)
+2.5 to +3.2
Ground
Black
• If the voltage is correct, replace the system board.
• If the voltage is not correct, replace the backup battery.
• If the backup battery discharges quickly after replacement, replace the system board.
30 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Related service information
This chapter presents following information:
•
•
•
•
Service Web site:
When the latest maintenance diskette and the system program service diskette become available, they will
be posted on http://support.lenovo.com.
Restoring the factory contents by using Recovery Disc Set
When the hard disk drive (HDD) or solid state drive (SSD) is replaced because of a failure, no product recovery
program is on the new drive. In this case, you must use the Recovery Disc Set for the computer. Order the
Recovery Disc Set and the drive at the same time so that you can recover the new drive with the pre-installed
software when they arrive. For information on which discs to order, see “Recovery discs” on page 107.
The recovery disc set consists of the user instructions and the following set of DVDs to restore the computer
to the original factory configuration.
Operating System Recovery Disc (one disc)
This disc restores the Microsoft® Windows operating system. Use this disc to start the recovery
process.
Applications and Drivers Recovery Disc (one or more discs)
This disc restores the preinstalled applications and drivers on the computer.
Supplemental Recovery Disc
This disc contains additional content, such as updates to the software that was preinstalled on the
computer. Not all recovery disc sets come with a Supplemental Recovery Disc.
Notes:
• You must have a DVD drive to use the recovery discs. If you do not have an internal DVD drive, you
can use an external USB DVD drive.
• During the recovery process, all data on the drive will be deleted. If possible, copy any important data
or personal files that you want to keep onto removable media or a network drive before you start the
recovery process.
To restore the computer to the original factory configuration using the recovery disc set, do the following:
Note: Recovery can take one to two hours to complete. The length of time depends on the method you use.
If you use recovery discs, the recovery process will take about two hours.
1. Make the CD/DVD drive the first startup device in the startup sequence using the following procedure:
a. Press and hold down the F1 key, and then turn on the computer. When the logo screen is displayed
or if you hear repeating beeps, release the F1 key. The Setup Utility program opens.
b. Use the arrow keys to select Startup Boot.
c. Select the CD/DVD drive as the 1st Boot Device.
2. Insert the Operating System Recovery Disc into the DVD drive.
© Copyright Lenovo 2009, 2011
31
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press F10 to save the Setup Utility configuration changes. Follow the instructions on the screen to
begin the recovery process.
4. Select your language and click Next.
5. Read the license. If you agree with the terms and conditions, select I accept these terms and
conditions and then click Next. If you do not agree with the terms and conditions, follow the
instructions on the screen.
6. Click Yes in the displayed window to begin the operating system recovery process.
7. Insert the Applications and Drivers Recovery Disc when prompted and then click OK to begin the
applications and drivers recovery process.
8. If you have a Supplemental Recovery Disc, insert it when prompted and click Yes. If you do not have a
Supplemental Recovery Disc, click No.
9. When all of the data has been copied from the last disc in the set and has been processed, remove the
disc and restart the computer.
Note: The rest of the recovery process is fully automated and no action is required by you. The
computer will restart into the Microsoft Windows desktop several times and you might experience
periods when no activity is apparent on the screen for several minutes at a time. This is normal.
10. When the recovery process is complete, the Set Up Windows screen is displayed. Follow the
instructions on the screen to complete the Windows setup.
11. After you have completed the Windows setup, you might want to restore the original startup sequence.
Start the Setup Utility program and then press F9 to restore the default settings. Press F10 to save and
exit the Setup Utility.
Note: After restoring a drive to the factory default settings, you might need to reinstall some device drivers.
Passwords
As many as three passwords may be needed for any ThinkPad Notebook: the power-on password (POP),
the hard-disk password (HDP), and the supervisor password (SVP).
If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is
turned on. The computer does not start until the password is entered.
Note: If only an SVP is installed, the password prompt does not appear when the operating system is booted.
Power-on password
A power-on password (POP) protects the system from being powered on by an unauthorized person. The
password must be entered before an operating system can be booted. For how to remove the POP, see
Hard-disk password
There are two hard-disk passwords (HDPs):
• User HDP—for the user
• Master HDP—for the system administrator, who can use it to get access to the hard disk even if the user
has changed the user HDP
Note: There are two modes for the HDP: User only and Master + User. The Master + User mode requires
two HDPs; the system administrator enters both in the same operation. The system administrator then
provides the user HDP to the system user.
Attention: If the user HDP has been forgotten, check whether a master HDP has been set. If it has, it can be
used for access to the hard disk drive. If no master HDP is available, neither Lenovo nor Lenovo authorized
32 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
service technicians provide any services to reset either the user or the master HDP, or to recover data from
the hard disk drive. The hard disk drive can be replaced for a scheduled fee.
Supervisor password
A supervisor password (SVP) protects the system information stored in the BIOS Setup Utility. The user must
enter the SVP in order to get access to the BIOS Setup Utility and change the system configuration.
Attention: If the SVP has been forgotten and cannot be made available to the service technician, there is no
service procedure to reset the password. The system board must be replaced for a scheduled fee.
How to remove the power-on password
To remove a POP that you have forgotten, do the following:
(A) If no SVP has been set:
1. Turn off the computer.
page 62.
4. Turn on the computer and wait until the POST ends. After the POST ends, the password prompt does
not appear. The POP has been removed.
5. Reinstall the backup battery and the battery pack.
(B) If an SVP has been set and is known by the service technician:
1. Turn on the computer.
2. When the ThinkPad logo comes up, immediately press F1 to enter BIOS Setup Utility.For models
supporting the Passphrase function, press F1 while the POP icon is appearing on the screen; then enter
the POP. For the other models, enter the POP.
Note: To check whether the ThinkPad Notebook you are servicing supports the Passphrase function,
enter the BIOS Setup Utility and go to Security ➙ Password. If the Using Passphrase item is displayed
in the menu, this function is available on the ThinkPad Notebook.
3. Select Security, using the cursor directional keys to move down the menu.
4. Select Password.
5. Select Power-On Password.
6. Type the current SVP in the Enter Current Password field. then leave the Enter New Password field
blank, and press Enter twice.
7. In the Changes have been saved window, press Enter.
8. Press F10; then, in the Setup confirmation window, select Yes.
How to remove the hard-disk password
Attention: If User only mode is selected and the user HDP has been forgotten and cannot be made
available to the service technician, neither Lenovo nor Lenovo authorized service technicians provide any
services to reset the user HDPs or to recover data from the hard disk drive. The hard disk drive can be
replaced for a scheduled fee.
To remove a user HDP that has been forgotten, when the SVP and the master HDP are known, do the
following:
1. Turn on the computer.
Chapter 4. Related service information 33
Download from Www.Somanuals.com. All Manuals Search And Download.
2. When the ThinkPad logo comes up, immediately press F1 to enter BIOS Setup Utility.For models
supporting the Passphrase function, press F1 while HDP icon is appearing on the screen; then enter the
master HDP. For the other models, enter the master HDP.
Note: To check whether the ThinkPad Notebook you are servicing supports the Passphrase function,
enter the BIOS Setup Utility and go to Security ➙ Password. If Using Passphrase item is displayed
in the menu, this function is available on the ThinkPad Notebook.
3. Select Security, using the cursor directional keys to move down the menu.
4. Select Password.
5. Select Hard-disk x password, where x is the letter of the hard disk drive. A pop-up window opens.
6. Select Master HDP.
7. Type the current master HDP in the Enter Current Password field. then leave the Enter New Password
field blank, and press Enter twice.
8. Press F10.
9. Select Yes in the Setup Configuration window. Both user HDP and master HDP will have been removed.
Power management
To reduce power consumption, the computer has three power management modes: screen blank, sleep,
and hibernation.
Screen blank mode
To put the computer into screen blank mode, do as follows:
1. Right-click the Power Manager Battery Gauge in the task bar.
2. Select Power off display.
Sleep mode
When the computer enters sleep mode, the following events occur in addition to what occurs in screen
blank mode:
• The LCD is powered off.
• The hard disk drive is powered off.
• The CPU stops.
To enter sleep mode, do as follows:
1. Click Start.
2. Click the triangle mark on the right side of the Shut down icon; then select Sleep.
To return from sleep mode, press the Fn key.
Hibernation mode
By using this mode, you can turn off your computer completely without saving files or exiting from any
applications that are running. When you enter hibernation, all open applications, folders, and files are saved
to the hard disk, and then the computer turns off.
To enter hibernation mode, do as follows:
1. Click Start.
2. Click the triangle mark on the right side of the Shut down icon; then select Hibernate.
To return from hibernation mode, press the power button for more than 4 seconds.
34 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom-to-FRU index
This section contains following information:
•
•
•
•
•
•
The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most
likely cause is listed first, in boldface type.
Note: Do the FRU replacement or other actions in the sequence shown in the column headed “FRU or
action, in sequence.” If replacing a FRU does not solve the problem, put the original part back in the
computer. Do not replace a nondefective FRU.
This index can also help you determine, during regular servicing, what FRUs are likely to need to be
replaced next.
A numeric error is displayed for each error detected in POST or system operation. In the displays, n can
be any number.
If no numeric code is displayed, check the narrative descriptions of symptoms. If the symptom is not
Note:
For a device not supported by diagnostic codes in the ThinkPad Notebooks, see the manual for that device
Numeric error codes
Table 2. Numeric error codes
FRU or action, in sequence
System board.
Symptom or error (beeps, if any)
0187
EAIA data access error—The access to EEPROM is failed.
(two short beeps)
0189
System board.
Invalid RFID configuration information area—The
EEPROM checksum is not correct.
(two short beeps)
0190
1. Charge the battery pack.
2. Battery pack.
Critical low-battery error
(two short beeps)
0191
1. Run BIOS Setup Utility, and then save current
setting by pressing F10.
System Security—Invalid Remote Change requested.
2. System board.
0210
Change keyboard, and restart the computer.
Stuck Key
(two short beeps)
0211
Keyboard error
(two short beeps)
Run interactive tests of the keyboard and the auxiliary
input device.
Chapter 4. Related service information 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 2. Numeric error codes (continued)
FRU or action, in sequence
System board.
Symptom or error (beeps, if any)
0230
Shadow RAM error—Shadow RAM fails at offset nnnn.
(two short beeps)
0231
1. DIMM.
2. System board.
System RAM error—System RAM fails at offset nnnn.
(two short beeps)
0232
1. DIMM.
2. System board.
Extended RAM error— Extended RAM fails at offset nnnn.
(two short beeps)
0250
1. Charge the backup battery for more than 8 hours
by connecting the ac adapter.
2. Replace the backup battery and run BIOS Setup
Utility to reset the time and date.
System battery error—System battery is dead.
(two short beeps)
0251
1. Charge the backup battery for more than 8 hours
by connecting the ac adapter.
System CMOS checksum bad— Default configuration
used.
(two short beeps)
2. Replace the backup battery and run BIOS Setup
Utility to reset the time and date.
0254
Turn off the computer and discharge CMOS. Then
restart the computer.
System NV7 Volume checksum bad- Default configuration
used
(two short beeps)
0260
System timer error.
(two short beeps)
1. Charge the backup battery for more than 8 hours
by connecting the ac adapter.
2. Replace the backup battery and run BIOS Setup
Utility to reset the time and date.
3. System board.
0270
1. Charge the backup battery for more than 8 hours
by connecting the ac adapter.
2. Replace the backup battery and run BIOS Setup
Utility to reset the time and date.
Real-time clock error.
(two short beeps)
3. System board.
0271
Run BIOS Setup Utility to reset the time and date.
Date and time error—Neither the date nor the time is set
in the computer.
(two short beeps)
0280
1. Load “Setup Default” in BIOS Setup Utility.
2. DIMM.
3. System board.
Previous boot incomplete— Default configuration used.
(two short beeps)
02D0
System cache error.
(two short beeps)
1. CPU.
2. System board.
02F0
CPU ID:xx Failed.
1. CPU.
2. System board.
02F5
DMA test failed.
(two short beeps)
1. DIMM.
2. System board.
02F6
Software NMI failed
(two short beeps)
1. DIMM.
2. System board.
36 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 2. Numeric error codes (continued)
FRU or action, in sequence
Symptom or error (beeps, if any)
02F7
1. DIMM.
2. System board.
Fail-safe timer NMI failed
(two short beeps)
1802
1. Remove the Mini PCI network card.
2. System board.
Unauthorized network card is plugged in—Turn off and
remove the miniPCI network card.
(two short beeps)
1804
1. Remove the wireless WAN card.
2. System board.
Unauthorized WAN card is plugged in—Power off and
remove the WAN card.
Error messages
Table 3. Error messages
FRU or action, in sequence
Symptom or error (beeps, if any)
Bad CRC2. Enter BIOS Setup Utility, and load Setup
defaults.
(two short beeps)
Press F1 to enter BIOS Setup Utility. Press F9, and
Enter to load the default setting. Then save the current
setting by pressing F10, and restart the computer.
Fan error.
(four short beeps, one long beep)
1. Fan.
2. Thermal grease.
3. System board.
DRAM is unplugged.
(one short beep, pause, three short beeps, pause, three
short beeps, pause, one short beep.)
Memory card is not installed. Install memory card.
Reinstall the memory card.
DRAM is not well plugged.
(one short beep, pause, three short beeps, pause, three
short beeps, pause, one short beep.)
Operating system not found.
1. Check that the operating system has no failure
and is installed correctly.
2. Enter BIOS Setup Utility and see whether the hard
disk drive is properly identified. If you still see the
same error message, check the boot sequence.
3. Reinstall the hard disk drive.
4. Reinstall the operating system.
System Configuration Data Read Error
(two short beeps)
Press F1 to enter BIOS Setup Utility. Press F9, and
Enter to load the default setting. Then save the current
setting by pressing F10, and restart the computer.
No-beep symptoms
Table 4. No-beep symptoms
Symptom or error
FRU or action, in sequence
1. Make sure that every connector is connected
tightly and correctly.
No beep, power-on indicator on, LCD blank, and no
POST.
2. DIMM.
3. System board.
1. Reseat DIMM.
2. System board.
No beep, power-on indicator on, and LCD blank during
POST.
Chapter 4. Related service information 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4. No-beep symptoms (continued)
Symptom or error
FRU or action, in sequence
The power-on password prompt appears.
A power-on password or a supervisor password is set.
Type the password and press Enter.
The hard-disk password prompt appears.
A hard-disk password is set. Type the password and
press Enter.
LCD-related symptoms
Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a
small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but
excessive pixel problems can cause viewing concerns.
If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty. However, if the
LCD has three or more visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced.
Note:
• This policy applies to all ThinkPad Notebooks purchased on 1 January, 2008 or later.
• Lenovo will not provide replacement if the LCD is within specification as we cannot guarantee that any
replacement LCD will have zero pixel defects.
• One pixel consists of R, G, B sub-pixels.
Table 5. LCD-related symptoms
FRU or action, in sequence
Symptom or error
No beep, power-on indicator on, and a blank LCD during System board.
POST.
• LCD backlight not working.
• LCD too dark.
• LCD brightness cannot be adjusted.
• LCD contrast cannot be adjusted.
1. Reseat the LCD connectors.
2. LCD assembly.
3. System board.
• LCD screen unreadable.
• Characters missing pixels.
• Screen abnormal.
1. See important note for “LCD-related symptoms.”
2. Reseat all LCD connectors.
3. LCD assembly.
• Wrong color displayed.
4. System board.
Horizontal or vertical lines displayed on LCD.
LCD assembly.
Intermittent problems
Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware
defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be
considered only when a problem recurs.
When analyzing an intermittent problem, do the following:
1. Run the diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRUs.
3. If any error is detected, replace the FRU shown by the FRU code. Rerun the test to verify that no
more errors exist.
38 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Undetermined problems
If the diagnostic tests did not identify the adapter or device that has failed, if wrong devices are installed,
or if the system simply is not operating, follow these procedures to isolate the failing FRU (do not isolate
FRUs that have no defects).
Verify that all attached devices are supported by the computer.
Verify that the power supply being used at the time of the failure is operating correctly. (See “Power system
1. Turn off the computer.
2. Visually check each FRU for damage. Replace any damaged FRU.
3. Remove or disconnect all of the following devices:
a. Non-ThinkPad devices
b. Printer, mouse, and other external devices
c. Battery pack
d. Hard disk drive
e. External diskette drive or optical drive
f. DIMM
g. Optical disk or diskette in the internal drive
h. PC Cards
4. Turn on the computer.
5. Determine whether the problem has been solved.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRUs one at a time (do not replace a nondefective FRU):
a. System board
b. LCD assembly
Chapter 4. Related service information 39
Download from Www.Somanuals.com. All Manuals Search And Download.
40 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Status indicators
This chapter presents the system status indicators that show the status of the computer.
1
2
3
4
Table 6. Status indicators
Indicator
Meaning
1
On-screen
indicators
Caps lock:
Caps Lock mode is enabled. You can enter all alphabetic characters
(A-Z) in uppercase without pressing the Shift key.
Wireless status:
Press F9 to enable or disable the wireless features. You can quickly
change the power state of each feature in the list.
2
Power status
Green:
The AC adapter is connected. If a battery is installed on the computer, it
is charged when this indicator is on.
© Copyright Lenovo 2009, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
41
Table 6. Status indicators (continued)
Indicator
Meaning
Off:
The AC adapter is not connected.
3
Sleep (standby)
status
The illumination dot in the ThinkPad logo on the outer lid of the computer and on the
palm rest works as a system-status indicator: it shows whether the computer is in
sleep (standby), hibernation, or normal mode.
Red:
The computer is on (in normal mode).
Fast blinking red:
The computer is entering sleep (standby) or hibernation mode.
Slow blinking red:
4
Sleep (standby)
status
The computer is in sleep (standby) mode.
Off:
The computer is off or in hibernation mode.
42 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Special keys
This computer has several special keys at the upper row of the keyboard. To use each function, directly
press the desired key.
Note: To use F1 - F12 functions, press Fn and the desired function key simultaneously; this is the default
setting.
The following table shows the function of each special key.
Table 7. Fn key combinations
Description
Special key
Speaker mute (F1)
If you mute the sound and then turn off the computer, the sound will remain muted when you
turn on the computer again. To turn on the sound, press the Speaker volume up or Speaker
volume down keys.
Speaker volume
down (F2)
Speaker volume up
(F3)
Microphone mute
(F4)
When you press the microphone mute key, all of the recording devices are set on mute or
unmute; this is the default setting.
Camera mute (F5)
During a video conference, you can control the video streaming from the integrated camera by
pressing this key. The video output will be grayed out, and the audio streaming will continue.
For Windows 7:
Switching a display
output location (F6)
Switch between the computer display and an external monitor. Windows will show these
display options:
• Computer display only (LCD)
• Computer display and external monitor (same image)
• Computer display and external monitor (extended desktop function)
• External monitor only
Note: To switch between the computer display and an external monitor, the Win+P key
combination is also available.
Display brightness
down (F7)
The computer display becomes dimmer.
The purpose of this method is to change the brightness level temporarily. To change the
default brightness level, change the settings of the Power Option in the Control Panel or
use the Power Manager.
© Copyright Lenovo 2009, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Table 7. Fn key combinations (continued)
Description
Special key
Display brightness up The computer display becomes brighter.
(F8)
The purpose of this method is to change the brightness level temporarily. To change the
default brightness level, change the settings of the Power Option in the Control Panel or
use the Power Manager.
Wireless radio control Enable or disable the built-in wireless networking features. If you press this key, a list of
(F9)
wireless features is displayed. You can quickly change the power state of each feature
in the list.
Notes: To use this function, following device drivers must be installed on the computer
beforehand:
• Power Management driver
• OnScreen Display Utility
• Wireless device drivers
For Multimedia control.
Previous track/scene
(F10)
Play/pause (F11)
Next track/scene
(F12)
44 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. FRU replacement notices
External CRU statement to customers:
Some problems with your product can be resolved with a replacement part you can install yourself, called
a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as Self-service CRUs and others
are designated as Optional-service CRUs. Installation of Self-service CRUs is your responsibility; you may
request that Lenovo installs an Optional-service CRU according to the warranty service for your product.
Where you are installing the CRU, Lenovo will ship the CRU to you. CRU information and replacement
instructions are shipped with your product and are available from Lenovo at any time upon request. You may
find a list of CRUs in the publications that ship with your product or at http://www.lenovo.com/CRUs. You
may be required to return the defective part that is replaced by the CRU. When return is required: (1) return
instructions, a prepaid shipping label, and a container will be included with the replacement CRU; and (2) you
may be charged for the replacement CRU if Lenovo does not receive the defective part within thirty (30) days
of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.
This chapter presents notices related to removing and replacing parts. Read this chapter carefully before
replacing any FRU.
Screw notices
Loose screws can cause a reliability problem. In the ThinkPad Notebook, this problem is addressed with
special nylon-coated screws that have the following characteristics:
• They maintain tight connections.
• They do not easily come loose, even with shock or vibration.
• They are harder to tighten.
• Each one should be used only once.
Do the following when you service this machine:
• Always use new screws.
• Use a torque screwdriver if you have one.
Tighten screws as follows:
• Plastic to plastic
Turn an additional angle of 90 degrees after the screw head touches the surface of the plastic part.
• Logic card to plastic
Turn an additional angle of 180 degrees after the screw head touches the surface of the logic card.
© Copyright Lenovo 2009, 2011
45
Download from Www.Somanuals.com. All Manuals Search And Download.
• Torque driver
If you have a torque driver, refer to the “Torque” column for each step.
• Make sure that you use the correct screw. If you have a torque screwdriver, tighten all screws firmly to the
torque shown in the table. Never use a screw that you removed. Use a new one. Make sure that all
of the screws are tightened firmly.
• Ensure torque screw drivers are calibrated correctly following country specifications.
Retaining serial numbers
This section includes the following descriptions:
•
•
•
Restoring the serial number of the system unit
When the computer was manufactured, the EEPROM on the system board was loaded with the serial
numbers of the system and all major components. These numbers need to remain the same throughout
the life of the computer.
If you replace the system board, you must restore the serial number of the system unit to its original value.
Before replacing the system board, save the original serial number by doing the following:
1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the
computer.
2. From the main menu, select 1. Set System Identification.
3. Select 2. Read S/N data from EEPROM.
The serial number of each device in your computer is displayed; the serial number of the system unit is
listed as follows:
• 20: Serial number
Write down that number.
Note: The serial number of the system unit is also written on the label attached to the bottom of the computer.
After you have replaced the system board, restore the serial number by doing the following:
1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later and restart the
computer.
2. From the main menu, select 1. Set System Identification.
3. Select 1. Add S/N data from EEPROM. Follow the instructions on the screen.
If the MTM and Product ID numbers differ from each other on the rear label, use what is shown for the
Product ID field. See example below:
46 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
MTM on rear label:
TTTT-CTO S/N SSSSSSS
Product ID on rear label:
TTTT-MMM (Use this number when setting Serial Number)
In the example, the Serial Number to be input is '1STTTTMMMSSSSSSS'.
Retaining the UUID
The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to your computer at
production and stored in the EEPROM of your system board. The algorithm that generates the number is
designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same
number.
When you replace the system board, you must set the UUID on the new system board as follows:
1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the
computer.
2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already
exists, it is not overwritten.
Reading or writing the ECA information
Information on Engineering Change Announcements (ECA) are stored in the EEPROM of the system board.
The electronic storage of this information simplifies the procedure to check if the ECA has been previously
applied to a machine. The machine does not need to be disassembled to check for the ECA application.
To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write
function on the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later.
1. Insert the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the
computer.
2. From the main menu, select 6. Set ECA Information.
3. To read ECA information, select 2. Read ECA/rework number from EEPROM and follow the
instruction.
4. To read box build date, select 5. Read box build date from EEPROM, and follow the instruction on
the screen.
After an ECA has been applied to the machine, the EEPROM must be updated to reflect the ECA's
application. Use the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later to update the
EEPROM.
Note: Only the ECA number is stored in the EEPROM. The machine type of the ECA is assumed be the same
as the machine type of the machine that had the ECA applied to it.
1. Insert the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the
computer.
2. From the main menu, select 6. Set ECA Information.
3. To write ECA information, select 1. Write ECA/rework number from EEPROM, and follow the
instruction.
4. To write box build date, select 4. Write box build date from EEPROM, and follow the instruction on
the screen.
If the system board is being replaced, try to read the ECA information from the old system board and transfer
the information to the new system. If the system board is inoperable, this will not be possible.
Chapter 7. FRU replacement notices 47
Download from Www.Somanuals.com. All Manuals Search And Download.
48 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Removing and replacing a FRU
External CRU statement to customers:
Some problems with your product can be resolved with a replacement part you can install yourself, called
a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as Self-service CRUs and others
are designated as Optional-service CRUs. Installation of Self-service CRUs is your responsibility; you may
request that Lenovo installs an Optional-service CRU according to the warranty service for your product.
Where you are installing the CRU, Lenovo will ship the CRU to you. CRU information and replacement
instructions are shipped with your product and are available from Lenovo at any time upon request. You may
find a list of CRUs in the publications that ship with your product or at http://www.lenovo.com/CRUs. You
may be required to return the defective part that is replaced by the CRU. When return is required: (1) return
instructions, a prepaid shipping label, and a container will be included with the replacement CRU; and (2) you
may be charged for the replacement CRU if Lenovo does not receive the defective part within thirty (30) days
of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.
This chapter presents directions and drawings for use in removing and replacing a FRU. Be sure to observe
the following general rules:
1. Do not try to service any computer unless you have been trained and certified. An untrained person runs
the risk of damaging parts.
3. Begin by removing any FRUs that have to be removed before the failing FRU. Any such FRUs are listed
at the top of the page. Remove them in the order in which they are listed.
4. Follow the correct sequence in the steps for removing the FRU, as given in the drawings by the
numbers in square callouts.
5. When turning a screw to replace a FRU, turn it in the direction as given by the arrow in the drawing.
6. When removing the FRU, move it in the direction as given by the arrow in the drawing.
7. To put the new FRU in place, reverse the removal procedure and follow any notes that pertain to
replacement. For information about connecting and arranging internal cables, see Chapter 9 “Locations”
on page 89.
8. When replacing a FRU, use the correct screw as shown in the procedures.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets,
remove the battery pack, and then disconnect any interconnecting cables.
Attention: After replacing a FRU, do not turn on the computer until you have made sure that all screws,
springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking
the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical
short circuits.
Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before
touching it, establish personal grounding by touching a ground point with one hand or by using an
electrostatic discharge (ESD) strap (P/N 6405959).
© Copyright Lenovo 2009, 2011
49
Download from Www.Somanuals.com. All Manuals Search And Download.
1010 Battery pack
Important notice for replacing a battery pack:
ThinkVantage Toolbox has an automatic battery diagnostic that determines if the battery pack is defective. A battery
pack FRU should not be replaced unless this diagnostic shows that the battery is defective.
The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue.
If ThinkVantage Toolbox is not installed in the computer, the customer should download this program before a
non-physically damaged battery pack is replaced. Note that a physically damaged battery pack is non-warranty
replacement.
Removal steps of battery pack
DANGER
Use only the battery specified in the parts list for your computer. Any other battery could ignite
or explode.
Unlock the battery latch 1 . Holding the battery latch in the unlocked position 2 , remove the battery pack in
the direction shown by arrow 3 .
2
1
3
When installing: Install the battery pack in the slot, and then make sure that the battery latch is in the
locked position.
1020 Bottom slot cover
For access, remove this FRU:
•
50 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal steps of bottom slot cover
Note: Loosen the screws 1 , but do not remove them.
1
1
1
2
1
1
When installing: Make sure that all the projections of the cover are attached firmly to the frame. Then
secure the screws.
Applying label to the bottom slot cover
When you replace the cover, following label needs to be peeled off from the old cover, and needs to be
put on the new cover:
1
Asset tag label
For the label location, refer to the following figure:
Chapter 8. Removing and replacing a FRU 51
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1030 DIMM
For access, remove these FRUs in order:
•
•
Removal steps of DIMM
1
2
1
a
b
Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ),
but not in SLOT-1 ( b ).
When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it
until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.
52 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1040 Hard disk drive (HDD)
For access, remove these FRUs in order:
•
•
Attention:
• Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock.
Improper handling can cause damage and permanent loss of data.
• Before removing the drive, have the user make a backup copy of all the information on it if possible.
• Never remove the drive while the system is operating or is in suspend mode.
Removal steps of HDD
1
Torque
Step
Screw (quantity)
Color
1
Black
0.181 Nm
M2 × 3 mm, flat-head, nylon-coated (1)
(1.85 kgfcm)
2
Chapter 8. Removing and replacing a FRU 53
Download from Www.Somanuals.com. All Manuals Search And Download.
3
When installing: Make sure that the HDD connector is attached firmly.
1050 PCI Express Mini Card for wireless LAN
For access, remove these FRUs in order:
•
•
Removal steps of PCI Express Mini Card for wireless LAN
In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the
connectors with your fingers and gently unplug them in direction of the arrow.
54 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2
2
1
Torque
Step
Screw (quantity)
Color
2
Black
0.181 Nm
M2 × 3 mm, flat-head, nylon-coated (2)
(1.85 kgfcm)
3
When installing: Plug the gray cable into the jack marked MAIN or M, and the black cable into the jack
marked AUX or A on the card.
1060 PCI Express Mini Card for wireless WAN
For access, remove these FRUs in order:
Chapter 8. Removing and replacing a FRU 55
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Removal steps of PCI Express Mini Card for wireless WAN
In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the
connectors with your fingers and gently unplug them in direction of the arrow.
2
2
1
Torque
Step
Screw (quantity)
Color
2
Black
0.181 Nm
M2 × 3 mm, flat-head, nylon-coated (2)
(1.85 kgfcm)
3
56 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
When installing: Plug the red cable into the jack marked MAIN, and the blue cable into the jack marked
AUX on the card.
1070 Keyboard
For access, remove these FRUs in order:
•
•
Removal steps of keyboard
1
1
Torque
Step
Screw (quantity)
Color
1
Black
0.181 Nm
M2 × 5 mm, flat-head, nylon-coated (2)
(1.85 kgfcm)
In step 2 , by using a plastic pry tool, push the keyboard out from two square holes in the battery pack slot
as shown in this figure.
2
Chapter 8. Removing and replacing a FRU 57
Download from Www.Somanuals.com. All Manuals Search And Download.
3
5
6
7
8
7
4
Installation steps of keyboard
When installing the keyboard, do as follows:
1. Attach the keyboard connectors.
2. Attach the keyboard so that the keyboard front edges are under the frame as shown in this figure.
58 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Secure the keyboard by tightening the screws from the bottom side of the computer.
1080 Top case assembly and microphone module
For access, remove these FRUs in order:
•
•
•
•
Note: Microphone module is attached on the underside of the top case assembly.
Removal steps of top case assembly and microphone module
1
1
1
1
1
1
1
1
1
1
Torque
Step
Screw (quantity)
M2 × 5 mm, flat-head, nylon-coated (10)
Color
1
Black
0.181 Nm
(1.85 kgfcm)
Chapter 8. Removing and replacing a FRU 59
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal steps of top case assembly and microphone module
2
2
2
2
2
2
Torque
Step
Screw (quantity)
Color
2
Black
0.181 Nm
M2 × 3 mm, flat-head, nylon-coated (6)
(1.85 kgfcm)
3
3
3
Torque
Step
Screw (quantity)
Color
3
Black
0.181 Nm
M2 × 3 mm, flat-head, nylon-coated (3)
(1.85 kgfcm)
60 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
6
7
8
When installing: Make sure that the connectors are attached firmly.
In step 5 , push the top case assembly out from the frame by using a plastic pry tool as shown in this figure.
Chapter 8. Removing and replacing a FRU 61
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal steps of backup battery
DANGER
Use only the battery specified in the parts list for your computer. Any other battery could ignite
or explode.
1
2
When installing: Make sure that the connector is attached firmly.
1100 Bluetooth daughter card (BDC-2)
For access, remove these FRUs in order:
•
•
•
•
Chapter 8. Removing and replacing a FRU 63
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal steps of BDC-2
1
2
Torque
Step
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (1)
Color
1
Black
0.181 Nm
(1.85 kgfcm)
When installing: Make sure that the connector is attached firmly.
1110 Speaker assembly
For access, remove these FRUs in order:
•
•
•
•
64 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal steps of speaker assembly
1
1
1
1
Torque
Step
Screw (quantity)
Color
2
Black
0.181 Nm
M2 × 3 mm, flat-head, nylon-coated (4)
(1.85 kgfcm)
2
3
3
Cable routing: Make sure that the connector is attached firmly and you route the cable as shown in this
figure.
Chapter 8. Removing and replacing a FRU 65
Download from Www.Somanuals.com. All Manuals Search And Download.
1120 System board and fan assembly
Important notices for handling the system board:
When handling the system board, bear the following in mind.
• The system board has an accelerometer, which can be broken by applying several thousands of G-forces.
Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject
the accelerometer to as much as 6,000 G's of shock.
• Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite.
• Avoid rough handling of any kind.
• At every point in the process, be sure not to drop or stack the system board.
• If you put a system board down, be sure to put it only on a padded surface such as an ESD mat or conductive
corrugated material.
For access, remove these FRUs in order:
•
•
•
•
•
•
•
•
•
•
•
Removal steps of system board and fan assembly
Following components soldered on the top side of the system board are extremely sensitive. When you
service the system board, avoid any kind of rough handling.
66 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
For CULV (Customer Ultra-Low Voltage) models (MT0196 and MT0492):
a Accelerometer chip for the HDD Active Protection
c GMCH (Graphics Memory Controller Hub)
System™
b CPU
d ICH (I/O Controller Hub)
a
b
c
d
Chapter 8. Removing and replacing a FRU 67
Download from Www.Somanuals.com. All Manuals Search And Download.
For CULV models (MT0217 and MT0250):
a Accelerometer chip for the HDD Active Protection
c PCH (Peripheral Control Hub)
System
b CPU
a
b
c
68 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
For AMD® models (MT0197):
a CPU
c South Bridge
b North Bridge
d Accelerometer chip for the HDD Active Protection
System
a
b
c
d
For AMD models (MT0221):
a Accelerometer chip for the HDD Active Protection
System
c North Bridge
b CPU
d South Bridge
b
c
a
d
Chapter 8. Removing and replacing a FRU 69
Download from Www.Somanuals.com. All Manuals Search And Download.
2
2
1
1
1
Torque
Step
Screw (quantity)
M2 × 3 mm, flat-head, nylon-coated (3)
Color
1
Black
0.181 Nm
(1.85 kgfcm)
Note: Loosen the screws 2 , but do not remove them.
70 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
When installing: Make sure that the connectors are attached firmly.
a
5
8
7
6
Chapter 8. Removing and replacing a FRU 71
Download from Www.Somanuals.com. All Manuals Search And Download.
When installing: Attach the system board so that the battery pins of the system board are attached firmly to
the guide hole of the base cover as shown in a in this.
Make sure that the connectors are attached firmly.
Note: Loosen the screws 9 , but do not remove them.
9
9
10
11
When installing:
• Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams,
on the part marked a as in the following figure. Either too much or too less application of grease can
cause a thermal problem due to imperfect contact with a component. You need to peel the thin film
off from the rubbers b .
For MT0196 and MT0492:
b
a
b
72 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
For MT0197:
a
a
For MT0217 and MT0250:
a
For MT0221:
a
a
When installing: Make sure that the fan connector is attached firmly.
1130 I/O card assembly, audio cable, and I/O cable
For access, remove these FRUs in order:
•
•
•
•
•
•
•
Chapter 8. Removing and replacing a FRU 73
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Removal steps of I/O card assembly, audio cable, and I/O cable
1
1
1
1
2
Torque
Step
Screw (quantity)
Color
2
Black
0.181 Nm
M2 × 3 mm, flat-head, nylon-coated (1)
(1.85 kgfcm)
4
3
6
5
74 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal steps of LCD unit
2
2
1
1
1
1
1
2
2
Torque
Step
Screw (quantity)
M2.5 × 5 mm, flat-head, nylon-coated (4)
Color
Black
2
0.392Nm
(4 kgfcm)
76 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3
3
Cable routing: Make sure that the cables are attached to the cable guides as shown in this figure. When
you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables
to be damaged by the cable guides, or a wire to be broken.
Chapter 8. Removing and replacing a FRU 77
Download from Www.Somanuals.com. All Manuals Search And Download.
1150 Base cover assembly and DC-in cable
For access, remove these FRUs in order:
•
•
•
•
•
•
•
•
•
•
Removal steps of base cover assembly and DC-in cable
1
1
1
1
2
Cable routing: Make sure that the cable is attached to the cable guides as shown in this figure. When you
route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be
damaged by the cable guides, or a wire to be broken.
78 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Applying labels to the base cover
The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the
base cover, you need to apply the following labels:
If the Windows Certificate of Authentication label (COA) 2 is attached to a part that is replaced, return the
old part with the label attached to the customer, or provide a letter to the customer stating what the label
was originally on the system and what the label part number, serial number, and product key were.
4
Information label under battery
8
FCC label
9
Homologation label
14
Serial number blank label
Following labels need to be peeled off from the old base cover, and need to be put on the new base cover.
1
Ethernet label
3
SID card label
5
SIM ICCID label
6
China Mobile label/China Telecom label
7
Non Encryption label/Indonesia rating label
10
Brazil ANATEL label
11
Israel homologation label
12
Malaysia SIRIM label
13
Indonesia Postel label
15
Wireless WAN label
16
Wireless LAN label
For some models, you also need to apply one or two FCC labels. Check the old base cover; if it has one or
two FCC labels, find duplicates of them in the label kit and apply them to the new base cover.
Chapter 8. Removing and replacing a FRU 79
Download from Www.Somanuals.com. All Manuals Search And Download.
For the location of each label, refer to the following figure:
1
2
3
4
16
15
5
14
6
13
12
7
11
10
9
8
2010 LCD bezel assembly
For access, remove this FRU:
•
Removal steps of LCD bezel assembly
1
1
1
1
Torque
Step
Screw cap
Screw (quantity)
M2 × 4 mm, flat-head, nylon-coated (4)
Color
1
0.181 Nm
Silver
(1.85 kgfcm)
80 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2
2
2
2
2
2
2
2
2
2
2020 Integrated camera
For access, remove these FRUs in order:
•
•
Removal steps of integrated camera
2
1
When installing: Make sure that the connector of the integrated camera is attached firmly.
Chapter 8. Removing and replacing a FRU 81
Download from Www.Somanuals.com. All Manuals Search And Download.
2030 LCD panel and LCD cable
For access, remove these FRUs in order:
•
•
•
•
•
•
•
•
•
•
Removal steps of LCD panel and LCD cable
1
1
1
1
Torque
Step
Screw (quantity)
M1.7 × 3 mm, flat-head, nylon-coated (4)
Color
1
0.181 Nm
Silver
(1.85 kgfcm)
82 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2
4
3
8
5
6
7
Chapter 8. Removing and replacing a FRU 83
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal steps of hinge kit
2
1
1
2
Torque
Step
Screw (quantity)
Color
2
Black
0.181 Nm
M2 × 3 mm, flat-head, nylon-coated (2)
(1.85 kgfcm)
3
3
2050 Wireless LAN antenna assembly, wireless WAN antenna assembly,
and LCD rear cover assembly
For access, remove these FRUs in order:
•
Chapter 8. Removing and replacing a FRU 85
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
•
•
•
•
•
•
•
•
Removal steps of wireless LAN antenna assembly, wireless WAN antenna assembly, and LCD rear
cover assembly
2
2
2
2
1
1
1
1
3
3
3
3
3
3
86 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable routing: When you install the antenna assembly, route the cables as shown in the figures below.
As you route the cables, make sure that they are not subjected to any tension. Tension could cause the
cables to be damaged by the cable guides, or a wire to be broken.
a : Wireless LAN MAIN antenna (gray)
b : Wireless WAN MAIN antenna (red)
c : Wireless WAN AUX antenna (blue)
d : Wireless LAN AUX antenna (black)
a
b
c
d
Chapter 8. Removing and replacing a FRU 87
Download from Www.Somanuals.com. All Manuals Search And Download.
88 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9. Locations
This chapter presents the location of ThinkPad Edge 13” features and hardware.
Front view
1
Integrated camera (for some models)
2
Power switch
3
AC power connector
4
Status indicators
5
Power universal serial bus (USB) connectors (MT0217, MT0221, and MT0250)
Universal serial bus (USB) connectors (MT0196, MT0197, MT0492)
6
Universal serial bus (USB) connectors
7
Combo audio jack
8
Media Card Reader slot
9
Status indicators
10
TrackPoint pointing stick
11
TrackPoint buttons
12
Touch pad buttons
13
Touch pad
UltraNav®
14
15
Built-in microphone
© Copyright Lenovo 2009, 2011
89
Download from Www.Somanuals.com. All Manuals Search And Download.
1
15
2
3
13
4
12
5
6
7
11
14
8
10
9
Bottom view
1
Battery pack latch
2
3
4
5
6
7
Battery pack
Security keyhole
External monitor connector
HDMI port
RJ-45 (Ethernet) connector
Power USB connector (MT0196, MT0197, and MT0492)
eSATA/USB connector (MT0217, MT0221, and MT0250)
8
9
Built-in stereo speakers
HDD slot door
1
2
1
3
9
4
5
6
8
7
90 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10. Parts list
This chapter contains following lists of the service parts.
•
•
•
•
•
•
•
•
Notes:
• Each FRU is available for all types or models, unless specific types or models are specified.
• FRU with specific models listed and described as xxU (where U is an example of a country designator) should be
used for all models ending in U.
• FRU with specific models listed and described as 3Dx (where 3D is an example of a unique configuration) should be
used for all of these models, unless specific country or region designator is specified.
• A CRU (customer replaceable unit) is identified by a single asterisk (*) or two asterisks (**) in the CRU ID column. An
N in the CRU ID column means that the part is not a CRU. A single asterisk (*) means that the part is a Self-service
CRU; two asterisks (**) means that the part is an Optional-service CRU.
External CRU statement to customers:
Some problems with your product can be resolved with a replacement part you can install yourself, called
a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as Self-service CRUs and others are
designated as Optional-service CRUs. Installation of Self-service CRUs is your responsibility; you may request
that Lenovo installs an Optional-service CRU according to the warranty service for your product. Where you are
installing the CRU, Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped
with your product and are available from Lenovo at any time upon request. You may find a list of CRUs in the
publications that ship with your product or at http://www.lenovo.com/CRUs. You may be required to return the
defective part that is replaced by the CRU. When return is required: (1) return instructions, a prepaid shipping label,
and a container will be included with the replacement CRU; and (2) you may be charged for the replacement CRU if
Lenovo does not receive the defective part within thirty (30) days of your receipt of the replacement CRU. See your
Lenovo Limited Warranty documentation for full details.
ThinkPad computers contain the following types of CRUs:
– Self-service CRUs: These CRUs unplug or are held by no more than two screws. Examples of these types
of CRUs include the ac power adapter, power cord, battery, and hard disk drive. Other Self-service CRUs
depending on product design may include the memory module, wireless card, keyboard, and palm rest with
finger print reader and touchpad.
– Optional-service CRUs: These CRUs are isolated parts within the computer that are concealed by an access
panel that is typically secured by more than two screws. Once the access panel is removed, the specific
CRU is visible.
© Copyright Lenovo 2009, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
91
Table 8. Parts list—Overall
No.
FRU no.
FRU (Overall)
CRU
ID
1
2
3
3
4
Top case assembly for 0196, 0197, and 0429
Top case assembly for 0217, 0221, and 0250
60Y5520
04W0342
N
N
60Y3263 **
Qualcom Gobi-2000 WWAN, WW SKU
• 0196-CTO,
• 0197-CTO
• 0492-CTO
• 0217-CTO
• 0221-CTO
• 0250-CTO
4
4
60Y3259 **
60Y3225 **
Qualcom Gobi-2000 WWAN, Malaysia SKU
• 0196-CTO, 2Ex, 2Gx, 2Jx, 2Lx, 2Qx, 34x, 36x, 38x, 3Ax, 55x, 5Mx, 56x, 5Jx, 5Kx
• 0197-CTO, 2Qx, 2Tx, 2Ux, 2Vx, 4Qx, 4Sx, 4Ux, 6Kx, 6Mx, 6Px, 7Hx, 7Wx, 7Yx, 82x, 8Ax
• 0492-CTO, 24x, 28x
Leadcore LC5730D WWAN for China mobile
• 0196-CTO, 5Gx, 5Hx
• 0197-CTO, 7Ex
• 0492-CTO
• 0217-CTO
• 0221-CTO
• 0250-CTO
4
5
60Y3227 **
Huawei EM660 WWAN for China telecom
• 0196-CTO
• 0197-CTO, 7Fx
• 0492-CTO
• 0217-CTO
• 0221-CTO
• 0250-CTO
43Y6553 **
60Y3177
ThinkPad 1x2 11b/g/n Wireless LAN Mini-PCI Express Adapter II
• 0196-CTO, 27x, 28x, 29x, 2Cx, 2Hx, 2Jx, 2Mx, 2Rx, 2Zx, 32x, 33x, 34x, 35x, 36x, 37x,
38x, 39x, 3Ax, 3Bx, 55x, 56x, 58x, 59x, 5Ax, 5Bx, 5Cx, 3Yx, 3Zx, 42x, 43x, 44x, 45x,
46x, 47x, 48x, 49x, 4Ax, 4Bx, 5Kx
• 0197-CTO, 22x 23x 24x 25x 26x, 27x, 28x, 29x, 2Ax, 2Cx, 73x, 2Dx, 2Ex, 2Fx, 2Hx, 2Jx,
2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Zx, 32x, 33x, 34x, 35x, 36x,
37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx,
3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax,
4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx,
4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx,
5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Vx, 5Wx,
5Xx, 5Yx, 63x, 66x, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 6Gx, 6Hx, 6Jx, 6Kx, 6Lx, 6Mx, 6Nx,
6Px, 6Qx, 6Rx, 6Sx, 6Tx, 6Ux, 6Vx, 6Wx, 6Xx, 6Yx, 6Zx, 72x, 74x, 75x, 76x, 77x, 78x, 79x,
7Ax, 7Bx, 7Cx, 7Dx, 7Ex, 7Fx, 7Gx, 7Hx, 7Jx, 7Kx, 7Lx, 7Mx, 7Nx, 7Px, 7Qx, 7Rx, 7Sx,
7Tx, 7Ux, 7Vx, 7Wx, 7Xx, 7Yx, 7Zx, 82x, 83x, 84x, 85x, 86x, 87x, 88x, 89x, 8Ax, 8Bx, 8Cx
• 0492-CTO, 22x, 23x, 26x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Mx, 2Nx, 2Px,
2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx, 32x, 33x, 37x, 38x, 39x, 3Ax, 3Bx,
3Cx, 3Lx, 3Mx, 3Nx, 3Px, 52x, 3Wx, 3Xx
Chapter 10. Parts list 93
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 8. Parts list—Overall (continued)
No.
FRU no.
FRU (Overall)
CRU
ID
5
60Y3247 **
60Y3249
ThinkPad 1x1 11b/g/n Wireless LAN PCI Express Half Mini Card Adapter
• 0217-CTO, 22x, 23x, 25x, 2Zx, 3Ax, 3Bx, 3Ex
• 0221-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx,
2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx,
32x, 33x, 34x, 36x, 37x, 39x, 3Ax, 3Bx, 3Cx, 3Dx
• 0250-CTO, 22x, 23x, 24x, 25x, 2Jx, 2Kx, 2Lx, 2Mx
5
5
60Y3251 **
60Y3241 **
ThinkPad 2x2 11a/b/g/n Wireless LAN PCI Express Half Mini Card Adapter
• 0217-CTO, 24x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Dx
• 0221-CTO, 35x, 38x
• 0250-CTO
Intel® Centrino® Wireless-N 1000
• 0196-CTO, 23x, 24x, 25x, 26x, 2Ax, 2Bx, 57x, 2Dx, 2Ex, 2Fx, 2Gx, 2Kx, 2Lx, 2Px, 2Qx,
2Wx, 2Xx, 2Yx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx,
3Sx, 3Tx, 3Ux, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, 4Ux, 4Vx, 4Wx, 4Xx,
4Yx, 53x, 54x, 5Dx, 5Fx, 5Gx, 5Hx, 5Jx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx
• 0197-CTO
• 0492-CTO, 24x, 25x, 2Hx, 2Jx, 2Kx, 2Lx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Qx, 3Rx, 3Sx,
3Tx, 3Ux, 3Vx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx
• 0217-CTO, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Jx, 2Kx, 2Lx,
2Mx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 32x, 3Cx, 3Fx, 3Gx
• 0221-CTO
• 0250-CTO, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Nx, 2Px, 2Qx
5
5
60Y3195 **
Intel Centrino Advanced-N + WiMAX 6250, WW SKU
• 0196-CTO, 22x, 4Qx, 4Rx, 4Sx, 5Ex
• 0197-CTO
• 0492-CTO
• 0217-CTO
• 0221-CTO
• 0250-CTO
60Y3209 **
Intel Centrino Advanced-N + WiMAX 6250, Russia SKU
• 0196-CTO
• 0197-CTO
• 0492-CTO, 3Kx
• 0217-CTO
• 0221-CTO
• 0250-CTO
6
6
6
40Y8403 **
55Y3712 **
55Y3715 **
1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card
• 0196-CTO
• 0197-all
• 0492-CTO
1-GB DDR3-1067 SDRAM SO-DIMM (PC2-8500) card
• 0196-all
• 0197-CTO
• 0492-all
1-GB DDR3-1333 SDRAM SO-DIMM (PC3-10600) card
• 0196-all
• 0197-CTO
• 0492-all
• 0217-CTO, 2Vx, 2Zx, 32x, 3Fx
• 0221-CTO, 2Vx, 2Xx, 32x, 33x, 34x
• 0250-CTO
94 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 8. Parts list—Overall (continued)
No.
FRU no.
FRU (Overall)
CRU
ID
6
40Y8404 **
55Y3713 **
55Y3716 **
2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card
• 0196-CTO
• 0197-all
• 0492-CTO
6
6
2-GB DDR3-1067 SDRAM SO-DIMM (PC2-8500) card
• 0196-all
• 0197-CTO
• 0492-all
2-GB DDR3-1333 SDRAM SO-DIMM (PC3-10600) card
• 0196-all
• 0197-CTO
• 0492-all
• 0217-CTO, 22x, 23x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Jx,
2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Vx, 2Yx, 2Zx, 32x, 36x, 3Ax, 3Cx, 3Bx, 3Ex, 3Fx, 3Gx
• 0221-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx,
2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx,
32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx
• 0250-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx,
2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx
6
55Y3717 **
4-GB DDR3-1333 SDRAM SO-DIMM (PC3-10600) card
• 0217-CTO, 24x, 25x, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Wx, 2Xx, 33x, 34x, 35x, 37x, 38x, 39x, 3Dx
• 0221-CTO, 3Ex, 3Fx
• 0250-CTO
7
7
45M2905
04W0350
63Y2127
04W0355
45M2901
N
N
N
N
N
*
I/O cable for 0196, 0197, and 0492
I/O cable for 0217, 0221, and 0250
Function board assembly for 0196, 0197, and 0492
Function board assembly for 0217, 0221, and 0250
DC-in cable
8
8
9
10
42T4805
42T4857
Battery pack, Li-ion (4 cell) 73
• 0196-CTO, 23x, 27x, 2Ax, 57x, 2Fx, 2Hx, 2Kx, 2Mx, 2Px, 2Rx, 2Zx, 32x, 33x, 34x, 35x,
36x, 3Bx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Jx, 4Lx, 4Mx,
4Nx, 4Px, 4Qx, 53x, 54x
• 0197-CTO, 26x, 28x, 2Kx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx,
3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx,
4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Rx, 4Tx, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x,
57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px,
5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Vx, 6Gx, 6Hx, 6Jx, 6Kx, 6Lx, 6Mx, 72x, 76x, 79x, 7Ax, 7Px,
7Qx, 7Rx, 7Sx, 7Tx, 7Ux, 7Vx, 7Wx, 7Xx, 7Yx, 84x, 8Bx
• 0492-CTO, 22x, 23x, 24x, 25x, 26x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Mx, 2Nx,
2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx, 32x, 33x, 3Kx, 4Bx
• 0217-CTO, 2Nx, 2Px, 3Ex
• 0221-CTO, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Jx, 2Kx, 2Qx, 2Rx, 3Bx, 3Cx, 3Dx
• 0250-CTO, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx
Chapter 10. Parts list 95
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 8. Parts list—Overall (continued)
No.
FRU no.
FRU (Overall)
CRU
ID
10
42T4813
42T4858
*
Battery pack, Li-ion (6 cell) 73+
• 0196-CTO, 22x, 24x, 25x, 26x, 28x, 29x, 2Bx, 2Cx, 2Dx, 2Ex, 2Gx, 2Jx, 2Lx, 2Qx, 2Wx,
2Xx, 2Yx, 37x, 38x, 39x, 3Ax, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 55x, 56x, 3Kx, 3Lx,
3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 58x, 59x, 5Ax, 5Bx, 5Cx, 4Cx, 4Dx, 4Ex, 4Fx,
4Gx, 4Rx, 4Sx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx,
5Nx, 5Px, 5Qx
• 0197-CTO, 22x 23x 24x 25x 27x, 29x, 2Ax, 2Cx, 73x, 2Dx, 2Ex, 2Fx, 2Hx, 2Jx, 2Lx, 2Mx,
2Nx, 2Ux, 2Vx, 2Wx, 2Zx, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex,
3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 4Qx, 4Sx, 4Ux, 5Wx, 5Xx, 5Yx, 63x,
66x, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 6Nx, 6Px, 6Qx, 6Rx, 6Sx, 6Tx, 6Ux, 6Vx, 6Wx, 6Xx,
6Yx, 6Zx, 74x, 75x, 77x, 78x, 7Bx, 7Cx, 7Dx, 7Ex, 7Fx, 7Gx, 7Hx, 7Jx, 7Kx, 7Lx, 7Mx, 7Nx,
7Zx, 82x, 83x, 85x, 86x, 87x, 88x, 89x, 8Ax, 8Cx
• 0492-CTO, 2Gx, 2Hx, 2Jx, 2Kx, 2Lx, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx,
3Hx, 3Jx, 3Lx, 3Mx, 3Nx, 3Px, 52x, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx,
42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Cx, 4Dx
• 0217-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx,
2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx, 32x, 33x,
34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Dx, 3Cx, 3Bx, 3Fx, 3Gx
• 0221-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Lx, 2Mx, 2Nx, 2Px, 2Sx, 2Tx,
2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax
• 0250-CTO, 22x, 23x, 24x, 25x, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx
11 Base cover assembly for 0196
11 Base cover assembly for 0197
11 Base cover assembly for 0492
11 Base cover assembly for 0217, 0221, and 0250
12 HDD cover bracket
60Y5528
60Y5530
60Y5529
04W0349
60Y5532
60Y5517
N
N
N
N
N
N
13 HDD slot cover
14
60Y4763 **
SATA hard disk drive, 160 GB, 5,400 rpm
• 0196-CTO, 3Qx, 4Qx
• 0197-CTO, 2Kx, 2Lx, 2Sx, 39x, 3Fx
• 0492-CTO, 2Gx, 2Hx, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax
14
60Y4755 **
75Y5061
SATA hard disk drive, 160 GB, 5,400 rpm
• 0196-CTO, 3Qx, 4Qx
75Y5071
• 0197-CTO, 2Kx, 2Lx, 2Sx, 39x, 3Fx
• 0492-CTO, 2Gx, 2Hx, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax
• 0217-CTO
• 0221-CTO
• 0250-CTO
14
60Y4765 **
SATA hard disk drive, 250 GB, 5,400 rpm
• 0196-CTO, 23x, 27x, 2Ax, 2Cx, 3Bx, 3Rx, 3Yx, 44x, 48x, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Wx,
54x, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Nx, 5Px
• 0197-CTO, 26x, 27x, 28x, 2Hx, 2Mx, 2Px, 2Tx, 2Vx, 32x, 33x, 34x, 35x, 3Ax, 3Bx, 3Cx,
3Ex, 3Gx, 3Hx, 3Jx, 3Rx, 3Sx, 3Wx, 3Xx, 43x, 44x, 48x, 49x, 4Dx, 4Ex, 4Jx, 4Kx, 4Vx,
4Wx, 4Zx, 52x, 55x, 56x, 59x, 5Ax, 5Dx, 5Ex, 5Hx, 5Jx, 5Mx, 5Nx, 5Rx, 5Sx, 6Xx, 6Yx,
79x, 7Dx, 7Ex, 7Fx, 88x, 8Bx, 8Cx
• 0492-CTO, 23x, 26x, 28x, 2Ex, 2Fx, 2Jx, 2Lx, 2Mx, 2Nx, 2Sx, 2Tx, 2Xx, 2Yx, 3Kx, 52x, 4Dx
96 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 8. Parts list—Overall (continued)
No.
FRU no.
FRU (Overall)
CRU
ID
14
60Y4757 **
75Y5063
75Y5073
SATA hard disk drive, 250 GB, 5,400 rpm
• 0196-CTO, 23x, 27x, 2Ax, 2Cx, 3Bx, 3Rx, 3Yx, 44x, 48x, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Wx,
54x, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Nx, 5Px
• 0197-CTO, 26x, 27x, 28x, 2Hx, 2Mx, 2Px, 2Tx, 2Vx, 32x, 33x, 34x, 35x, 3Ax, 3Bx, 3Cx,
3Ex, 3Gx, 3Hx, 3Jx, 3Rx, 3Sx, 3Wx, 3Xx, 43x, 44x, 48x, 49x, 4Dx, 4Ex, 4Jx, 4Kx, 4Vx,
4Wx, 4Zx, 52x, 55x, 56x, 59x, 5Ax, 5Dx, 5Ex, 5Hx, 5Jx, 5Mx, 5Nx, 5Rx, 5Sx, 6Xx, 6Yx,
79x, 7Dx, 7Ex, 7Fx, 88x, 8Bx, 8Cx
• 0492-CTO, 23x, 26x, 28x, 2Ex, 2Fx, 2Jx, 2Lx, 2Mx, 2Nx, 2Sx, 2Tx, 2Xx, 2Yx, 3Kx, 52x, 4Dx
• 0217-CTO, 24x, 35x, 36x, 37x, 38x, 39x
• 0221-CTO, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Zx, 35x
• 0250-CTO
14
60Y4767 **
SATA hard disk drive, 320 GB, 5,400 rpm
• 0196-CTO, 22x, 28x, 29x, 2Bx, 57x, 2Dx, 2Ex, 2Fx, 2Hx, 2Kx, 2Mx, 2Px, 2Rx, 2Wx, 2Xx,
2Yx, 2Zx, 32x, 33x, 34x, 35x, 36x, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Px, 3Sx, 3Tx, 3Ux, 58x,
5Ax, 5Bx, 5Cx, 3Zx, 45x, 49x, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, 4Rx, 4Sx, 4Ux, 4Vx, 53x, 5Lx, 5Mx
• 0197-CTO, 26x, 27x, 28x, 2Hx, 2Mx, 2Px, 2Tx, 2Vx, 32x, 33x, 34x, 35x, 3Ax, 3Bx, 3Cx,
3Ex, 3Gx, 3Hx, 3Jx, 3Rx, 3Sx, 3Wx, 3Xx, 43x, 44x, 48x, 49x, 4Dx, 4Ex, 4Jx, 4Kx, 4Vx,
4Wx, 4Zx, 52x, 55x, 56x, 59x, 5Ax, 5Dx, 5Ex, 5Hx, 5Jx, 5Mx, 5Nx, 5Rx, 5Sx, 6Xx, 6Yx,
79x, 7Dx, 7Ex, 7Fx, 88x, 8Bx, 8Cx
• 0492-CTO, 22x, 24x, 25x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Kx, 2Px, 2Ux, 2Zx, 37x, 38x, 39x,
3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx,
3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 4Bx
14
60Y4759 **
75Y5065
75Y5075
SATA hard disk drive, 320 GB, 5,400 rpm
• 0196-CTO, 22x, 28x, 29x, 2Bx, 57x, 2Dx, 2Ex, 2Fx, 2Hx, 2Kx, 2Mx, 2Px, 2Rx, 2Wx, 2Xx,
2Yx, 2Zx, 32x, 33x, 34x, 35x, 36x, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Px, 3Sx, 3Tx, 3Ux, 58x,
5Ax, 5Bx, 5Cx, 3Zx, 45x, 49x, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, 4Rx, 4Sx, 4Ux, 4Vx, 53x, 5Lx, 5Mx
• 0197-CTO, 26x, 27x, 28x, 2Hx, 2Mx, 2Px, 2Tx, 2Vx, 32x, 33x, 34x, 35x, 3Ax, 3Bx, 3Cx,
3Ex, 3Gx, 3Hx, 3Jx, 3Rx, 3Sx, 3Wx, 3Xx, 43x, 44x, 48x, 49x, 4Dx, 4Ex, 4Jx, 4Kx, 4Vx,
4Wx, 4Zx, 52x, 55x, 56x, 59x, 5Ax, 5Dx, 5Ex, 5Hx, 5Jx, 5Mx, 5Nx, 5Rx, 5Sx, 6Xx, 6Yx,
79x, 7Dx, 7Ex, 7Fx, 88x, 8Bx, 8Cx
75Y5163
• 0492-CTO, 22x, 24x, 25x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Kx, 2Px, 2Ux, 2Zx, 37x, 38x, 39x,
3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx,
3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 4Bx
• 0217-CTO, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Zx, 3Ex
• 0221-CTO, 23x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Kx, 2Mx
• 0250-CTO, 23x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Kx, 2Mx
14
14
60Y4773 **
45N7281
SATA hard disk drive, 320 GB, 7,200 rpm
• 0196-CTO, 24x, 25x, 26x, 3Kx, 4Xx, 4Yx, 5Qx
• 0197-CTO, 22x 23x 29x, 2Ax, 2Cx, 73x, 2Zx, 6Zx, 78x
• 0492-CTO, 42x, 4Cx
60Y4777 **
75Y5127
75Y5169
SATA hard disk drive, 320 GB, 7,200 rpm
• 0196-CTO, 24x, 25x, 26x, 3Kx, 4Xx, 4Yx, 5Qx
• 0197-CTO, 22x 23x 29x, 2Ax, 2Cx, 73x, 2Zx, 6Zx, 78x
• 0492-CTO, 42x, 4Cx
75Y5189
• 0217-CTO, 22x, 23x, 28x, 29x, 2Ax, 2Bx, 2Ex, 2Fx, 2Gx, 2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Vx, 3Ax
• 0221-CTO, 23x, 26x, 27x, 28x, 2Ax, 2Lx, 2Mx, 2Nx, 2Px, 36x, 3Dx
• 0250-CTO, 2Px, 2Qx
14
60Y4769 **
SATA hard disk drive, 500 GB, 5,400 rpm
• 0196-CTO, 2Gx, 2Jx, 2Lx, 2Qx, 37x, 38x, 39x, 3Ax, 3Cx, 55x, 56x, 3Lx, 3Mx, 3Nx, 59x,
42x, 43x, 46x, 47x, 4Ax, 4Bx, 5Jx, 5Kx
• 0197-CTO, 24x 25x 36x, 3Ux, 3Vx, 3Zx, 42x, 46x, 47x, 4Bx, 4Cx, 4Gx, 4Hx, 4Mx, 4Nx,
4Qx, 4Sx, 4Ux, 6Nx, 6Px, 7Px, 7Qx, 7Rx, 7Sx, 7Tx, 7Ux, 7Zx, 82x
• 0492-CTO, 2Qx, 2Rx, 2Vx, 2Wx, 32x, 33x
Chapter 10. Parts list 97
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 8. Parts list—Overall (continued)
No.
FRU no.
FRU (Overall)
CRU
ID
14
60Y4761 **
75Y5067
75Y5077
SATA hard disk drive, 500 GB, 5,400 rpm
• 0196-CTO, 2Gx, 2Jx, 2Lx, 2Qx, 37x, 38x, 39x, 3Ax, 3Cx, 55x, 56x, 3Lx, 3Mx, 3Nx, 59x,
42x, 43x, 46x, 47x, 4Ax, 4Bx, 5Jx, 5Kx
• 0197-CTO, 24x 25x 36x, 3Ux, 3Vx, 3Zx, 42x, 46x, 47x, 4Bx, 4Cx, 4Gx, 4Hx, 4Mx, 4Nx,
4Qx, 4Sx, 4Ux, 6Nx, 6Px, 7Px, 7Qx, 7Rx, 7Sx, 7Tx, 7Ux, 7Zx, 82x
• 0492-CTO, 2Qx, 2Rx, 2Vx, 2Wx, 32x, 33x
• 0217-CTO, 25x, 26x, 27x, 2Yx, 32x, 3Cx, 3Bx
• 0221-CTO, 22x, 24x, 25x, 2Wx, 34x
• 0250-CTO, 22x, 24x, 2Jx, 2Lx
14
14
15
04W0252 **
75Y5129
SATA hard disk drive, 500 GB, 7,200 rpm
• 0217-CTO, 2Cx, 2Dx, 2Wx, 2Xx, 33x, 34x, 3Dx, 3Fx, 3Gx
• 0221-CTO, 29x
• 0250-CTO, 2Nx
04W1378 **
04W1868
SATA solid state drive, 128 GB
• 0217-CTO
• 0221-CTO
• 0250-CTO
60Y5754
60Y5518
60Y5519
04W0343
04W0344
45M2904
63Y1554
N
N
N
N
N
N
N
Speaker assembly
16 Thermal module with fan for 0196 and 0492
16 Thermal module with fan for 0197
16 Thermal module with fan for 0217 and 0250
16 Thermal module with fan for 0221
17 Audio cable
System board assembly, Intel Core® 2 Duo processor (SU7300)
18
• 0196-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 57x, 2Dx, 2Ex, 2Fx, 2Gx,
2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Px, 2Qx, 2Rx, 2Wx, 2Xx, 2Yx, 2Zx, 32x, 33x, 34x, 35x, 36x, 37x,
38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 55x, 56x, 3Kx, 3Lx, 3Mx, 3Nx, 3Px,
3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 58x, 59x, 5Ax, 5Bx, 5Cx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x,
48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Ux,
4Vx, 4Wx, 4Xx, 4Yx, 53x, 54x, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx
• 0492-CTO, 22x, 23x, 24x, 25x, 3Gx, 3Hx, 3Jx, 3Wx, 3Zx, 4Bx
18
18
63Y1556
63Y1562
N
N
System board assembly, Intel Core 2 Solo processor (SU4100)
• 0196-CTO
• 0492-CTO, 26x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Jx, 2Kx, 2Lx, 2Mx,
2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx, 32x, 33x, 37x, 38x, 39x, 3Ax,
3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Lx, 3Mx, 3Nx, 3Px, 3Kx, 52x, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx,
3Xx, 3Yx, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Cx, 4Dx
System board assembly, AMD Athlon Neo X2 Dual-Core L325
• 0197-CTO, 25x 26x, 27x, 28x, 29x, 2Ax, 2Cx, 2Dx, 2Ex, 2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Px,
2Sx, 2Vx, 32x, 35x, 37x, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 43x, 44x, 45x,
46x, 47x, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Px, 4Rx, 4Tx, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx,
5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Vx, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 6Gx, 6Hx,
6Jx, 6Kx, 6Lx, 6Mx, 6Qx, 6Rx, 6Sx, 6Xx, 6Yx, 6Zx, 72x, 74x, 76x, 77x, 79x, 7Ax, 7Bx, 7Dx,
7Px, 7Rx, 7Tx, 7Vx, 7Wx, 7Xx, 7Yx, 84x, 85x, 86x, 88x, 8Bx, 8Cx
98 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 8. Parts list—Overall (continued)
No.
FRU no.
FRU (Overall)
CRU
ID
18
63Y1560
N
System board assembly, AMD Turion Neo X2 Dual-Core L625
• 0197-CTO, 22x 23x 24x 73x, 2Fx, 2Nx, 2Qx, 2Rx, 2Tx, 2Ux, 2Wx, 2Zx, 33x, 34x, 36x, 38x,
39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 48x,
49x, 4Ax, 4Bx, 4Cx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Qx, 4Sx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx,
52x, 53x, 54x, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Wx, 5Xx, 5Yx, 63x, 66x, 6Nx,
6Px, 6Tx, 6Ux, 6Vx, 6Wx, 75x, 78x, 7Cx, 7Ex, 7Fx, 7Gx, 7Hx, 7Jx, 7Kx, 7Lx, 7Mx, 7Nx,
7Qx, 7Sx, 7Ux, 7Zx, 82x, 83x, 87x, 89x, 8Ax
18
18
63Y1564
75Y4174
N
N
System board assembly, AMD Athlon Neo X2 Single-Core MV-40
• 0197-CTO
System board assembly, Intel ULV U5400 PDC
• 0217-CTO, 2Ex, 2Fx, 2Gx, 2Nx, 2Zx
• 0250-CTO, 26x, 27x, 28x
18
18
04W1353
04W0295
N
N
System board assembly, Intel ULV U5600 PDC
• 0217-CTO, 3Ex
• 0250-CTO, 2Qx
System board assembly, Intel ULV i3-380UM
• 0217-CTO, 22x, 23x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Hx, 2Jx, 2Px, 2Qx, 2Rx, 2Sx,
2Tx, 2Ux, 2Vx, 2Wx, 2Yx, 32x, 36x, 37x, 39x, 3Ax, 3Dx, 3Cx, 3Bx, 3Fx, 3Gx
• 0250-CTO, 22x, 23x, 29x, 2Ax, 2Bx, 2Jx, 2Kx, 2Nx, 2Px
18
18
04W0294
75Y4178
N
N
System board assembly, Intel ULV i5-470UM
• 0217-CTO, 24x, 25x, 2Dx, 2Kx, 2Lx, 2Mx, 2Xx, 33x, 34x, 35x, 38x
• 0250-CTO, 24x, 25x, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Lx, 2Mx
System board assembly, AMD Athlon X2 K325
• 0221-CTO, 23x, 26x, 27x, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Lx, 2Mx, 2Qx, 2Rx, 2Sx, 2Tx,
2Ux, 2Vx, 2Wx, 2Zx, 32x, 35x
18
18
18
19
04W1354
75Y4176
04W1355
N
N
N
N
System board assembly, AMD Athlon X2 K345
• 0221-CTO
System board assembly, AMD Turion X2 K625
• 0221-CTO, 22x, 24x, 25x, 28x, 29x, 2Ax, 2Hx, 2Jx, 2Kx, 2Nx, 2Px, 2Xx, 2Yx, 33x, 34x, 36x
System board assembly, AMD Turion K685
• 0221-CTO
75Y5934
75Y5935
Bluetooth daughter card (BDC-2.1)
• 0196-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 57x, 2Dx, 2Ex, 2Fx,
2Gx, 2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Px, 2Qx, 2Rx, 2Wx, 2Xx, 2Yx, 2Zx, 32x, 33x, 34x, 35x,
36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 55x, 56x, 3Kx, 3Lx,
3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 58x, 59x, 5Ax, 5Bx, 5Cx, 43x, 47x, 4Bx, 4Cx,
4Dx, 4Ex, 4Fx, 4Gx, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, 4Rx, 4Sx, 4Ux, 4Vx, 4Xx, 4Yx, 53x, 54x,
5Ex, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx
• 0197-CTO, 22x 23x 29x, 2Ax, 2Cx, 73x, 2Dx, 2Ex, 2Fx, 2Hx, 2Jx, 2Mx, 2Nx, 2Px, 2Qx,
2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Zx, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx,
3Ex, 3Fx, 3Gx, 3Hx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Vx, 42x, 47x, 4Cx, 4Hx, 4Nx, 4Px,
4Qx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x,
5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx,
5Tx, 5Ux, 5Vx, 5Wx, 5Xx, 5Yx, 63x, 66x, 6Cx, 6Dx, 6Ex, 6Gx, 6Hx, 6Jx, 6Kx, 6Lx, 6Mx,
6Nx, 6Px, 6Qx, 6Rx, 6Sx, 6Tx, 6Ux, 6Vx, 6Wx, 6Zx, 72x, 74x, 75x, 76x, 77x, 78x, 79x, 7Ax,
7Bx, 7Cx, 7Gx, 7Hx, 7Jx, 7Kx, 7Lx, 7Mx, 7Nx, 7Px, 7Qx, 7Rx, 7Sx, 7Tx, 7Ux, 7Vx, 7Wx,
7Xx, 7Yx, 7Zx, 82x, 83x, 84x, 85x, 86x, 87x, 89x, 8Ax, 8Bx
• 0492-CTO, 22x, 23x, 24x, 25x, 26x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Gx, 2Hx, 2Jx, 2Kx,
2Lx, 2Rx, 2Wx, 33x, 37x, 38x, 39x, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Lx, 3Mx, 3Nx, 3Px,
3Kx, 52x, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x,
47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx
Chapter 10. Parts list 99
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 8. Parts list—Overall (continued)
No.
FRU no.
FRU (Overall)
CRU
ID
• 0217-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx,
2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx,
32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Dx, 3Cx, 3Bx, 3Ex, 3Fx, 3Gx
• 0221-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx,
2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx, 32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax,
3Bx, 3Cx, 3Dx
• 0250-CTO, 22x, 23x, 24x, 25x, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx
20 Backup battery for 0196, 0197, and 0492
20 Backup battery for 0217, 0221, and 0250
21 TrackPoint stick caps
93P4905
04W0332
91P9642
N
N
*
—
100 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 9. Parts list—13.3-inch HD LED-backlight LCD
No.
FRU no.
FRU (13.3-inch HD LED-backlight LCD)
CRU
ID
1
1
2
60Y5527
04W0348
N
N
N
LCD bezel assembly for 0196, 0197, and 0492
LCD bezel assembly for 0217, 0221, and 0250
Hinges, black
60Y5525
60Y5526
• 0196-CTO, 22x, 24x, 25x, 26x, 27x, 28x, 2Ax, 2Bx, 57x, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Jx,
2Kx, 2Lx, 2Mx, 2Xx, 2Yx, 2Zx, 35x, 36x, 39x, 3Ax, 3Bx, 3Cx, 3Ex, 3Fx, 3Hx, 3Jx, 56x, 3Lx, 04W0392
3Mx, 3Qx, 3Sx, 3Ux, 58x, 59x, 5Ax, 5Bx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x, 4Dx, 4Ex,
4Gx, 4Jx, 4Lx, 4Mx, 4Qx, 4Rx, 4Sx, 4Ux, 4Vx, 4Wx, 4Yx, 53x, 54x, 5Ex, 5Fx, 5Gx, 5Hx,
5Jx, 5Kx, 5Mx, 5Nx, 5Qx
• 0197-CTO, 22x 24x 26x, 27x, 28x, 29x, 2Cx, 73x, 2Dx, 2Fx, 2Hx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px,
2Qx, 2Sx, 2Tx, 2Ux, 2Wx, 2Zx, 34x, 35x, 36x, 38x, 39x, 3Ax, 3Dx, 3Ex, 3Fx, 3Hx, 3Jx, 3Kx,
3Lx, 3Mx, 3Nx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x,
47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Px, 4Qx, 4Rx, 4Sx, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x,
54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Vx, 5Wx, 5Xx, 63x, 66x, 69x, 6Bx, 6Cx, 6Dx,
6Gx, 6Jx, 6Kx, 6Nx, 6Px, 6Qx, 6Rx, 6Tx, 6Ux, 6Xx, 6Zx, 72x, 74x, 75x, 76x, 77x, 79x,
7Bx, 7Cx, 7Dx, 7Ex, 7Fx, 7Gx, 7Hx, 7Jx, 7Kx, 7Lx, 7Px, 7Qx, 7Rx, 7Sx, 7Vx, 7Wx, 7Zx,
82x, 84x, 85x, 87x, 88x, 89x, 8Ax, 8Bx, 8Cx
• 0492-CTO, 22x, 23x, 24x, 26x, 28x, 2Ax, 2Cx, 2Ex, 2Gx, 2Jx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx,
2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 38x, 39x, 3Ax, 3Cx, 3Dx, 3Fx, 3Gx, 3Jx, 3Lx, 3Mx, 3Nx,
3Kx, 52x, 3Rx, 3Sx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 43x, 44x, 45x, 46x, 48x, 49x, 4Dx
• 0217–CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 2Ax, 2Cx, 2Dx, 2Ex, 2Fx, 2Hx, 2Jx, 2Kx,
2Lx, 2Px, 2Qx, 2Sx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx, 32x, 33x, 35x, 36x, 37x, 3Ax, 3Dx,
3Cx, 3Bx, 3Fx, 3Gx
• 0221–CTO, 22x, 23x, 24x, 25x, 27x, 29x, 2Bx, 2Cx, 2Ex, 2Fx, 2Hx, 2Jx, 2Lx, 2Nx, 2Px,
2Qx, 2Sx, 2Ux, 2Vx, 2Wx, 2Xx, 2Zx, 32x, 33x, 34x, 35x, 36x, 37x, 3Ax, 3Cx, 3Dx, 3Ex, 3Fx
• 0250–CTO, 22x, 23x, 24x, 25x, 26x, 27x, 29x, 2Ax, 2Cx, 2Dx, 2Fx, 2Gx, 2Jx, 2Kx, 2Lx,
2Mx, 2Nx, 2Px, 2Qx
2
Hinges, silver
75Y4451
75Y4452
N
• 0196-CTO, 23x, 29x, 2Cx, 2Px, 2Qx, 2Rx, 2Wx, 32x, 33x, 34x, 37x, 38x, 3Dx, 3Gx, 55x,
3Kx, 3Nx, 3Px, 3Rx, 3Tx, 5Cx, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Fx, 4Nx, 4Px, 4Xx, 5Dx, 5Lx, 5Px 04W0393
• 0197-CTO, 23x 25x 2Ax, 2Ex, 2Jx, 2Rx, 2Vx, 32x, 33x, 37x, 3Bx, 3Cx, 3Gx, 3Px, 3Qx, 4Dx,
4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Tx, 4Ux, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx,
5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Yx, 6Ax, 6Ex, 6Hx, 6Lx, 6Mx, 6Sx,
6Vx, 6Wx, 6Yx, 78x, 7Ax, 7Mx, 7Nx, 7Tx, 7Ux, 7Xx, 7Yx, 83x, 86x
• 0492-CTO, 25x, 29x, 2Bx, 2Dx, 2Fx, 2Hx, 2Kx, 2Xx, 2Yx, 2Zx, 32x, 33x, 37x, 3Bx, 3Ex,
3Hx, 3Px, 3Qx, 3Tx, 42x, 47x, 4Ax, 4Bx, 4Cx
• 0217–CTO, 29x, 2Bx, 2Gx, 2Mx, 2Nx, 2Rx, 2Tx, 34x, 38x, 39x, 3Ex
• 0221–CTO, 26x, 28x, 2Ax, 2Dx, 2Gx, 2Kx, 2Mx, 2Rx, 2Tx, 2Yx, 38x, 39x, 3Bx
• 0250–CTO, 28x, 2Bx, 2Ex, 2Hx
3
Wireless LAN antenna cable set
45M2902 N
• 0196-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 57x, 2Dx, 2Ex, 2Fx, 2Gx,
2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Px, 2Qx, 2Rx, 2Wx, 2Xx, 2Yx, 2Zx, 32x, 33x, 34x, 35x, 36x, 37x,
38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 55x, 56x, 3Kx, 3Lx, 3Mx, 3Nx, 3Px,
3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 58x, 59x, 5Ax, 5Bx, 5Cx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x,
48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Jx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Ux,
4Vx, 4Wx, 4Xx, 4Yx, 53x, 54x, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx
• 0197-CTO, 22x 23x 24x 25x 26x, 27x, 28x, 29x, 2Ax, 2Cx, 73x, 2Dx, 2Ex, 2Fx, 2Hx, 2Jx,
2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Zx, 32x, 33x, 34x, 35x, 36x,
37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx,
3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax,
4Bx, 4Cx, 4Dx, 4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx,
4Ux, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx,
5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Vx, 5Wx,
5Xx, 5Yx, 63x, 66x, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 6Gx, 6Hx, 6Jx, 6Kx, 6Lx, 6Mx, 6Nx,
6Px, 6Qx, 6Rx, 6Sx, 6Tx, 6Ux, 6Vx, 6Wx, 6Xx, 6Yx, 6Zx, 72x, 74x, 75x, 76x, 77x, 78x, 79x,
102 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 9. Parts list—13.3-inch HD LED-backlight LCD (continued)
No.
FRU no.
FRU (13.3-inch HD LED-backlight LCD)
CRU
ID
7Ax, 7Bx, 7Cx, 7Dx, 7Ex, 7Fx, 7Gx, 7Hx, 7Jx, 7Kx, 7Lx, 7Mx, 7Nx, 7Px, 7Qx, 7Rx, 7Sx,
7Tx, 7Ux, 7Vx, 7Wx, 7Xx, 7Yx, 7Zx, 82x, 83x, 84x, 85x, 86x, 87x, 88x, 89x, 8Ax, 8Bx, 8Cx
• 0492-CTO, 22x, 23x, 24x, 25x, 26x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx,
2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx, 32x,
33x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Lx, 3Mx, 3Nx, 3Px,
3Kx, 52x, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x,
47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx
• 0217-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx,
2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Vx, 2Wx, 2Xx, 2Zx, 32x, 33x,
34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Dx, 3Bx, 3Ex, 3Fx, 3Gx
• 0221-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx,
2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx,
32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx
• 0250-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx,
2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx
4
4
60Y5744
N
N
Integrated camera (0.3 MP) for 0196, 0197, and 0492
Integrated camera (2.0 MP) for 0217, 0221, and 0250
04W0265
04W0266
04W0267
5
60Y5522
N
LCD rear cover assembly (midnight black, smooth)
• 0196-CTO, 24x, 26x, 2Bx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Jx, 2Yx, 3Bx, 3Fx, 3Hx, 3Mx, 3Sx,
58x, 59x, 5Ax, 44x, 45x, 46x, 47x, 4Qx, 4Rx, 4Sx, 4Ux, 4Vx, 54x, 5Ex, 5Fx, 5Gx, 5Hx,
5Jx, 5Kx, 5Mx, 5Qx
• 0197-CTO, 24x 26x, 27x, 2Cx, 2Hx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Sx, 2Tx, 2Ux, 2Wx,
3Ax, 3Dx, 3Fx, 3Jx, 3Lx, 3Nx, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Px, 4Qx,
5Vx, 5Wx, 5Xx, 63x, 6Bx, 6Cx, 6Rx, 6Ux, 72x, 76x, 77x, 79x, 7Bx, 7Cx, 7Gx, 7Hx, 7Jx,
7Lx, 7Rx, 7Sx, 84x, 88x, 89x, 8Ax, 8Bx, 8Cx
• 0492-CTO, 22x, 23x, 24x, 26x, 28x, 2Lx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 39x, 3Cx, 3Dx, 3Gx,
3Lx, 3Mx, 3Kx, 52x, 3Rx, 3Ux, 3Yx, 3Zx, 43x, 46x, 48x, 4Dx
5
60Y5523
N
LCD rear cover assembly (midnight black, gloss)
• 0196-CTO, 22x, 25x, 27x, 28x, 2Ax, 57x, 2Kx, 2Lx, 2Mx, 2Xx, 2Zx, 35x, 36x, 39x, 3Ax,
3Cx, 3Ex, 3Jx, 56x, 3Lx, 3Qx, 3Ux, 5Bx, 3Yx, 3Zx, 42x, 43x, 4Dx, 4Ex, 4Gx, 4Jx, 4Lx,
4Mx, 4Wx, 4Yx, 53x, 5Nx
• 0197-CTO, 2Dx, 2Fx, 2Zx, 34x, 35x, 36x, 38x, 39x, 3Ex, 3Hx, 3Kx, 3Mx, 3Rx, 3Sx, 3Tx,
3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 4Rx, 4Sx, 4Vx, 4Wx, 4Xx, 4Yx, 4Zx, 52x, 53x, 54x, 55x,
56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 66x, 69x, 6Dx, 6Gx, 6Jx, 6Kx, 6Nx, 6Px, 6Qx, 6Tx, 6Xx,
6Zx, 73x, 74x, 75x, 7Dx, 7Ex, 7Fx, 7Kx, 7Px, 7Qx, 7Vx, 7Wx, 7Zx, 82x, 85x, 87x
• 0492-CTO, 2Ax, 2Cx, 2Ex, 2Gx, 2Jx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx, 38x, 3Ax, 3Fx, 3Jx, 3Nx,
3Sx, 3Vx, 3Wx, 3Xx, 44x, 45x, 49x
5
60Y5524
N
LCD rear cover assembly (heatwave red, gloss)
• 0196-CTO, 23x, 29x, 2Cx, 2Px, 2Qx, 2Rx, 2Wx, 32x, 33x, 34x, 37x, 38x, 3Dx, 3Gx, 55x,
3Kx, 3Nx, 3Px, 3Rx, 3Tx, 5Cx, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Fx, 4Nx, 4Px, 4Xx, 5Dx, 5Lx, 5Px
• 0197-CTO, 23x 25x 2Ax, 2Ex, 2Jx, 2Rx, 2Vx, 32x, 33x, 37x, 3Bx, 3Cx, 3Gx, 3Px, 3Qx, 4Dx,
4Ex, 4Fx, 4Gx, 4Hx, 4Jx, 4Kx, 4Lx, 4Mx, 4Nx, 4Tx, 4Ux, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx,
5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Yx, 6Ax, 6Ex, 6Hx, 6Lx, 6Mx, 6Sx,
6Vx, 6Wx, 6Yx, 78x, 7Ax, 7Mx, 7Nx, 7Tx, 7Ux, 7Xx, 7Yx, 83x, 86x
• 0492-CTO, 25x, 29x, 2Bx, 2Dx, 2Fx, 2Hx, 2Kx, 2Xx, 2Yx, 2Zx, 32x, 33x, 37x, 3Bx, 3Ex,
3Hx, 3Px, 3Qx, 3Tx, 42x, 47x, 4Ax, 4Bx, 4Cx
5
04W0345 N
LCD rear cover assembly (midnight black smooth)
• 0217-CTO, 23x, 24x, 25x, 26x, 27x, 28x, 2Cx, 2Dx, 2Fx, 2Jx, 2Lx, 2Vx, 2Wx, 2Xx, 2Yx,
2Zx, 32x, 33x, 35x, 36x, 37x, 3Ax, 3Dx, 3Cx, 3Fx, 3Gx
• 0221-CTO, 23x, 24x, 25x, 29x, 2Cx, 2Fx, 2Jx, 2Px, 2Ux, 2Vx, 2Wx, 2Xx, 2Zx, 32x, 33x,
34x, 35x, 36x, 37x, 3Dx, 3Ex
• 0250-CTO, 22x, 23x, 24x, 25x, 27x, 2Ax, 2Dx, 2Gx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx
Chapter 10. Parts list 103
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 9. Parts list—13.3-inch HD LED-backlight LCD (continued)
No.
FRU no.
FRU (13.3-inch HD LED-backlight LCD)
CRU
ID
5
04W0346
N
LCD rear cover assembly (midnight black gloss)
• 0217-CTO, 22x, 2Ax, 2Ex, 2Hx, 2Kx, 2Px, 2Qx, 2Sx, 2Ux, 3Bx
• 0221-CTO, 22x, 27x, 2Bx, 2Ex, 2Hx, 2Lx, 2Nx, 2Qx, 2Sx, 3Ax, 3Cx, 3Fx
• 0250-CTO, 26x, 29x, 2Cx, 2Fx
5
04W0347
N
LCD rear cover assembly (red gloss)
• 0217–CTO, 29x, 2Bx, 2Gx, 2Mx, 2Nx, 2Rx, 2Tx, 34x, 38x, 39x, 3Ex
• 0221–CTO, 26x, 28x, 2Ax, 2Dx, 2Gx, 2Kx, 2Mx, 2Rx, 2Tx, 2Yx, 38x, 39x, 3Bx
• 0250–CTO, 28x, 2Bx, 2Ex, 2Hx
6
7
45M2900
45M2903
N
N
LCD cable
Wireless LAN/WAN antenna cable set
• 0196-CTO, 22x, 2Ex, 2Gx, 2Jx, 2Lx, 2Qx, 34x, 36x, 38x, 3Ax, 3Cx, 55x, 56x, 4Ux, 5Gx,
5Hx, 5Jx, 5Kx, 5Mx
• 0197-CTO, 22x 23x 2Qx, 2Tx, 2Ux, 2Vx, 36x, 3Dx, 3Jx, 4Qx, 4Sx, 4Ux, 6Kx, 6Mx, 6Px,
7Ex, 7Fx, 7Hx, 7Wx, 7Yx, 82x, 8Ax
• 0492-CTO, 24x, 28x, 3Qx, 3Rx, 3Sx, 48x, 49x, 4Ax
• 0217–CTO, 2Ux, 2Yx, 3Cx
• 0221–CTO
• 0250–CTO
8
8
27R2435
27R2437
27R2439
N
N
LCD module, 13.3-inch High Definition (HD) LED-backlight, glare
• 0196-all
• 0197-all
• 0492-all
93P5659
93P5657
LCD module, 13.3-inch HD LED-backlight, lower power, glare
• 0217-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx,
2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx,
32x, 33x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Dx, 3Ex, 3Fx, 3Gx
• 0221-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx,
2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx,
32x, 33x, 34x, 35x, 36x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx
• 0250-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx,
2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx
8
04W0470
04W0471
N
LCD module, 13.3-inch HD LED-backlight, anti-glare
• 0217-CTO, 3Bx, 3Cx
• 0221-CTO, 37x, 38x
• 0250-CTO
Keyboard
Table 10. Parts list—Keyboard
Language
CRU
ID
FRU No.
Arabic
60Y9443, 60Y9513
60Y9444, 60Y9514
60Y9442, 60Y9512
60Y9445, 60Y9515
60Y9440, 60Y9510
60Y9439, 60Y9509
60Y9446, 60Y9516
N
Belgian
Brazilian Portuguese
Bulgarian
Canadian French (058)
Canadian French (Acnor)
Czech
104 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 10. Parts list—Keyboard (continued)
Language
CRU
ID
FRU No.
Danish
60Y9447, 60Y9517
60Y9457, 60Y9527
60Y9464, 60Y9534
60Y9449, 60Y9519
60Y9450, 60Y9520
60Y9451, 60Y9521
60Y9452, 60Y9522
60Y9453, 60Y9523
60Y9454, 60Y9524
63Y0233, 63Y0231
60Y9455, 60Y9525
60Y9469, 60Y9539
60Y9456, 60Y9526
60Y9470, 60Y9540
60Y9441, 60Y9511
60Y9458, 60Y9528
60Y9459, 60Y9529
60Y9460, 60Y9530
60Y9461, 60Y9531
60Y9462, 60Y9532
60Y9463, 60Y9533
60Y9448, 60Y9518
60Y9465, 60Y9535
60Y9472, 60Y9542
60Y9471, 60Y9541
60Y9466, 60Y9536
60Y9467, 60Y9537
60Y9438, 60Y9508
60Y9468, 60Y9538
Dutch
Finnish, Swedish
French
German
Greek (U.S. English and Greek layout)
Hebrew
Hungarian
Icelandic
Indian English
Italian
Japanese
Kazakhstan
Korean
Latin American Spanish
Norwegian
Polish
Portuguese
Russian
Slovak
Slovenian
Spanish
Swiss
Thai
Traditional Chinese
Turkish
U.K. English
U.S. English
U.S. English (International, with a Euro symbol)
AC adapters
Table 11. Parts list—2-pin AC adapters
FRU
FRU no.
CRU
ID
42T5282
42T4423
42T4419
*
2-pin (65 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY)
2-pin (65 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY)
2-pin (65 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY)
Chapter 10. Parts list 105
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 12. Parts list—3-pin AC adapters
FRU
FRU no.
CRU
ID
42T5283
42T4421
42T4417
*
3-pin (65 W, 20 V) adapter (models CTO, xxG, xxM, xxQ, xxA, xxT, xxK, xxC, xxB, xxH, xxV)
3-pin (65 W, 20 V) adapter (models CTO, xxG, xxM, xxQ, xxA, xxT, xxK, xxC, xxB, xxH, xxV)
3-pin (65 W, 20 V) adapter (models CTO, xxG, xxM, xxQ, xxA, xxT, xxK, xxC, xxB, xxH, xxV)
Miscellaneous parts
Table 13. Parts list—Miscellaneous parts
FRU
FRU no.
CRU
ID
Microphone module
60Y5753
75Y5539
04W0356
60Y5521
N
N
N
N
Power switch board for 0196, 0197, and 0492
Power switch board for 0217, 0221, and 0250
Screw kit:
• M1.7 × 3 mm (silver), flat-head (6)
• M2 × 3 mm (black), flat-head (38)
• M2 × 4 mm (silver), flat-head (6)
• M2 × 5 mm (black), flat-head (18)
• M2.5 × 5 mm (black), flat-head (6)
• M3 × 3.5 mm (black), flat-head (3)
Power cords
A ThinkPad power cord for a specific country or region is usually available only in that country or region:
Table 14. Parts list—2-pin power cords
FRU No.
Country or region
CRU
ID
Argentina
• models -CTO, xxY
42T5020, 42T5105
42T5180, 42T5183
42T5008, 42T5093
42T5014, 42T5099
*
Brazil
• models -CTO, xxP
Canada, U.S.
• models -CTO, xxF, xxL, xxS, xxU
Japan
• models -CTO, xxE, xxJ
106 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 15. Parts list—3-pin power cords
FRU No.
Country or region
CRU
ID
Australia, New Zealand
• models -CTO, xxM
42T5050, 42T5135
42T5056, 42T5141
42T5004, 42T5089
42T5065, 42T5150
42T5041, 42T5126
42T5029, 42T5114
42T5083, 42T5168
42T5062, 42T5147
42T5047, 42T5132
42T5077, 42T5162
42T5044, 42T5129
42T5071, 42T5156
42T5035, 42T5120
*
Bangladesh, Sri Lanka, South Africa
• models -CTO, xxG
Canada, U.S.
• models -CTO, xxG, xxT
China (P.R.C.) (other than Hong Kong S.A.R.)
• models -CTO, xxC
Denmark
• models -CTO, xxG
European countries
• models -CTO, xxG
India
• models -CTO, xxQ
Israel
• models -CTO, xxG
Italy
• models -CTO, xxG
Korea
• models -CTO, xxK
Switzerland
• models -CTO, xxG
Taiwan
• models -CTO, xxV
U.K./Hong Kong S.A.R.
• models -CTO, xxB, xxG, xxH
Recovery discs
Windows 7 Home Basic (32 bit) DVDs
Windows 7 Home Basic (32 bit) is preinstalled as the operating system in the following models:
• 0196-CTO, 3Dx, 3Yx, 3Zx, 42x, 44x, 45x, 46x, 48x, 49x, 4Ax, 5Lx
• 0197-CTO, 2Fx, 2Px, 2Tx, 2Vx, 37x, 3Rx, 3Sx, 3Tx, 3Ux, 3Wx, 3Xx, 3Yx, 3Zx, 43x, 44x, 45x, 46x, 48x,
49x, 4Ax, 4Bx, 4Dx, 4Ex, 4Fx, 4Gx, 4Jx, 4Kx, 4Lx, 4Mx, 76x, 87x
• 0492-CTO, 24x, 2Hx, 2Jx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Sx, 2Tx, 2Ux, 2Vx, 2Xx, 2Yx, 2Zx, 32x, 43x, 44x
Chapter 10. Parts list 107
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 16. Parts list—Windows 7 Home Basic (32 bit) recovery DVDs
Language
P/N (with
MS 2010)
P/N (with
MS 2007)
CRU
ID
Brazilian Portuguese
Indian English
Russian
03W6668
03W6670
03W6672
03W6671
03W6674
03W6669
03W6673
03W6675
03W6676
58Y4046
76Y1510
58Y4049
58Y4048
58Y4051
76Y2671
58Y4050
58Y4052
58Y4053
*
Russian English
Serbian-Latin
Simplified Chinese
Spanish
Turkish
US English
• 0217-CTO, 2Zx, 32x, 3Ax, 3Fx, 3Gx
• 0221-CTO, 2Ex, 2Fx, 2Gx, 2Hx, 2Jx, 2Kx, 2Zx, 32x, 33x, 34x, 36x
• 0250-CTO, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Nx, 2Px, 2Qx
Table 17. Parts list—Windows 7 Home Basic (32 bit) recovery DVDs
Language
P/N (with
CRU
ID
MS 2010)
04T1613
04T1614
04T1617
04T1616
04T1618
04T1620
04T1619
04T1621
04T1622
04T1615
04T1623
04T1624
Arabic
*
Brazilian Portuguese
French
Indian English
Portuguese
Russian
Russian English
Spanish
Serbian-Latin
Simplified Chinese
Turkish
US English
Windows 7 Home Premium (32 bit) DVDs
Windows 7 Home Premium (32 bit) is preinstalled as the operating system in the following models:
• 0196-CTO, 3Cx, 3Ex, 3Fx, 3Gx, 59x, 5Ax, 5Bx, 5Cx, 43x, 47x, 4Bx
• 0197-CTO, 2Qx, 2Rx, 2Wx, 36x, 3Kx, 3Lx, 3Px, 3Vx, 42x, 47x, 4Cx, 4Hx, 4Nx, 69x, 6Ax, 6Bx, 72x, 78x,
7Ax, 7Bx, 7Cx, 7Jx, 7Mx, 7Px, 7Qx, 7Rx, 7Sx, 7Tx, 7Ux, 84x
• 0492-CTO, 22x, 25x, 26x, 28x, 29x, 2Ex, 2Fx, 2Kx, 2Rx, 2Wx, 33x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Mx,
3Nx, 3Px, 3Kx, 52x, 3Qx, 3Rx, 3Sx, 3Yx, 42x, 48x, 49x, 4Ax, 4Bx, 4Cx
108 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 18. Parts list—Windows 7 Home Premium (32 bit) recovery DVDs
Language
P/N (with
MS 2010)
P/N (with
MS 2007)
CRU
ID
Brazilian Portuguese
03W6677
03W6680
03W6683
03W6682
03W6688
03W6685
03W6684
03W6678
03W6686
03W6679
03W6681
03W6687
58Y4054
03W6297
58Y4058
76Y1511
76Y2816
58Y4060
58Y4059
76Y2672
58Y4061
58Y4056
58Y4057
58Y4064
*
C&L Hong Kong S.A.R. (Traditional Chinese/English/Simplified Chinese)
Korean
Indian English
Norwegian
Russian
Russian English
Simplified Chinese
Spanish
Traditional Chinese
Traditional Chinese (Hong Kong S.A.R.)
US English
• 0217-CTO
• 0221-CTO
• 0250-CTO
Table 19. Parts list—Windows 7 Home Premium (32 bit) recovery DVDs
Language
P/N (with
CRU
ID
MS 2010)
04T1626
04T1625
04T1627
Indian English
Simplified Chinese
US English
*
Windows 7 Home Premium (64 bit) DVDs
Windows 7 Home Premium (64 bit) is preinstalled as the operating system in the following models:
• 0196-CTO, 33x, 34x, 35x, 36x, 4Lx, 4Mx, 4Nx, 4Px, 4Qx, 5Fx, 5Nx, 5Px
• 0197-CTO, 24x 26x, 28x, 29x, 2Ax, 2Cx, 2Kx, 2Mx, 4Vx, 4Xx, 4Zx, 53x, 55x, 57x, 59x, 5Bx, 5Dx, 5Fx,
5Hx, 5Kx, 5Mx, 5Px, 5Rx, 5Tx, 6Jx, 6Kx, 6Lx, 6Mx, 7Vx, 7Wx, 7Xx, 7Yx, 89x, 8Ax
• 0492-CTO, 2Cx, 2Dx
Table 20. Parts list—Windows 7 Home Premium (64 bit) recovery DVDs
Language
P/N (with
MS 2010)
P/N (with
MS 2007)
CRU
ID
03W6738
03W6739
03W6740
58Y4141
58Y4142
58Y4143
C&L BelLux (English/French/German/Dutch)
C&L Sweden (English/Finland/Swedish )
C&L Switzerland (English/French/German/Italian)
Chapter 10. Parts list 109
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 20. Parts list—Windows 7 Home Premium (64 bit) recovery DVDs (continued)
Language
P/N (with
MS 2010)
P/N (with
MS 2007)
CRU
ID
03W6720
03W6721
03W6723
03W6724
03W6725
03W6726
03W6727
04T1599
03W6728
N/A
58Y4125
58Y4126
58Y4127
58Y4128
58Y4129
58Y4130
58Y4131
76Y1514
58Y4132
58Y4133
58Y4134
58Y4135
58Y4136
58Y4137
58Y4138
58Y4139
58Y4523
58Y4524
58Y4140
*
Czech
Danish
French
Greek
German
Hebrew
Hungarian
Indian English
Italian
Japanese
Polish
03W6729
03W6730
03W6731
03W6732
03W6733
03W6734
03W6735
03W6736
04T1600
Portuguese
Romanian
Slovak
Slovenian
Spanish
Serbian-Latin
Turkish
US English
110 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
• 0217-CTO, 22x, 26x, 2Ex, 2Fx, 2Gx, 2Qx, 2Rx, 35x, 37x, 38x, 39x, 3Bx
• 0221-CTO, 22x, 24x, 2Sx, 2Tx, 35x, 38x, 39x, 3Ax, 3Ex, 3Fx
• 0250-CTO, 22x, 23x, 24x, 25x, 2Jx, 2Kx, 2Lx, 2Mx
Table 21. Parts list—Windows 7 Home Premium (64 bit) recovery DVDs
Language
P/N
CRU
ID
Arabic
04T1628
04T1629
04T1654
04T1652
04T1653
04T1651
04T1632
04T1633
04T1634
04T1635
04T1636
04T1637
04T1638
04T1639
04T1640
04T1641
04T1642
04T1643
04T1644
04T1630
04T1645
04T1646
04T1647
04T1631
04T1648
04T1650
04T1649
*
Brazilian Portuguese
C&L Croatia (Croatian/Slovenian/English)
C&L EMEA (Dutch/French/German/English)
C&L Hong Kong S.A.R. (Traditional Chinese//Simplified Chinese/English)
C&L Nordics (Danish/Finnish/Swedish/Norway/English)
Czech
French
Greek
German
Hebrew
Hungarian
Japanese
Korean
Polish
Portuguese
Russian English
Romanian
Russian
Simplified Chinese
Slovak
Spanish
Serbian-Latin
Traditional Chinese
Turkish
US English
US English disable
Windows 7 Professional (32 bit) DVDs
Windows 7 professional (32 bit) is preinstalled as the operating system in the following models:
• 0196-CTO, 24x, 27x, 29x, 2Cx, 2Fx, 2Hx, 2Kx, 2Mx, 2Px, 2Rx, 3Bx, 3Hx, 3Jx, 3Px, 3Sx, 3Tx, 3Ux, 4Cx,
4Dx, 4Jx, 4Rx, 4Sx, 4Ux, 4Wx, 4Xx, 4Yx, 5Dx, 5Ex, 5Gx, 5Hx
• 0197-CTO, 27x, 2Ex, 2Hx, 2Jx, 2Zx, 38x, 3Ax, 3Bx, 3Dx, 3Ex, 3Gx, 3Jx, 4Px, 4Rx, 4Tx, 4Wx, 4Yx, 52x,
54x, 56x, 58x, 5Ax, 5Cx, 5Ex, 5Gx, 5Jx, 5Lx, 5Nx, 5Qx, 5Sx, 5Ux, 5Vx, 5Wx, 5Xx, 6Cx, 6Dx, 6Ex, 6Qx,
6Rx, 6Sx, 6Tx, 6Ux, 6Vx, 6Xx, 6Yx, 6Zx, 77x, 7Dx, 7Ex, 7Fx, 86x
• 0492-CTO, 3Gx, 3Hx, 3Jx, 3Zx
Chapter 10. Parts list 111
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 22. Parts list—Windows 7 professional (32 bit) recovery DVDs
Language
P/N (with
MS 2010)
P/N (with
MS 2007)
CRU
ID
Arabic
03W6637
03W6638
03W6665
03W6668
03W6666
03W6667
03W6641
03W6642
03W6644
03W6645
03W6646
03W6647
03W6650
03W6643
03W6651
N/A
58Y4065
58Y4066
58Y4092
03W6296
58Y4093
58Y4094
58Y4069
58Y4070
58Y4071
58Y4072
58Y4073
58Y4074
58Y4076
76Y1512
58Y4077
58Y4078
58Y4079
58Y4080
58Y4081
58Y4082
58Y4083
58Y4084
58Y4085
76Y2669
58Y4086
58Y4087
58Y4088
58Y4089
58Y4068
58Y4075
58Y4090
58Y4091
*
Brazilian Portuguese
C&L BelLux (English/French/German/Dutch)
C&L Hong Kong (Hong Kong/English/Simplified Chinese)
C&L Sweden (English/Finland/Swedish )
C&L Switzerland (English/French/German/Italian)
Czech
Danish
French
Greek
German
Hebrew
Hungarian
Indian English
Italian
Japanese
Korean
03W6652
03W6653
03W6654
03W6655
03W6656
03W6657
03W6658
03W6639
03W6659
03W6660
03W6661
03W6662
03W6640
03W6649
03W6663
03W6664
Norwegian
Polish
Portuguese
Russian English
Romanian
Russian
Simplified Chinese
Slovak
Slovenian
Spanish
Serbian-Latin
Traditional Chinese
Traditonal Chinese (Hong Kong S.A.R.)
Turkish
US English
Windows 7 Professional (64 bit) DVDs
Windows 7 Professional (64 bit) is preinstalled as the operating system in the following models:
• 0196-CTO, 22x, 23x, 25x, 26x, 28x, 2Ax, 2Bx, 57x, 2Dx, 2Ex, 2Gx, 2Jx, 2Lx, 2Qx, 37x, 38x, 39x, 3Ax,
55x, 56x, 3Kx, 3Lx, 3Mx, 3Nx, 53x, 5Jx, 5Kx, 5Mx
112 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
• 0197-CTO, 22x 23x 25x 73x, 2Dx, 2Nx, 2Ux, 3Mx, 3Nx, 3Qx, 4Qx, 4Sx, 4Ux, 6Nx, 6Px, 6Wx, 7Gx,
7Hx, 7Kx, 7Lx, 7Nx, 7Zx, 82x, 83x, 85x
• 0492-CTO
Table 23. Parts list—Windows 7 Professional (64 bit) recovery DVDs
Language
P/N (with
MS 2010)
P/N (with
MS 2007)
CRU
ID
Arabic
03W6689
03W6690
03W6717
03W6700
03W6718
03W6719
03W6693
03W6694
04T1597
03W6696
03W6697
03W6698
03W6699
03W6701
03W6702
03W6703
N/A
58Y4095
58Y4096
58Y4122
03W6298
58Y4123
58Y4124
58Y4099
58Y4100
76Y1513
58Y4101
58Y4102
58Y4103
58Y4104
58Y4105
58Y4106
58Y4107
58Y4108
58Y4109
58Y4110
58Y4111
58Y4112
58Y4113
58Y4114
58Y4115
76Y2673
58Y4116
58Y4117
58Y4118
58Y4119
58Y4098
58Y4120
58Y4121
*
Brazilian Portuguese
C&L BelLux (English/French/German/Dutch)
C&L Hong Kong S.A.R. (Traditional Chinese/English/Simplified Chinese)
C&L Sweden (English/Finland/Swedish)
C&L Switzerland (English/French/German/Italy)
Czech
Danish
Indian English
French
Greek
German
Hebrew
Hong Kong
Hungarian
Italian
Japanese
Korean
03W6704
03W6705
03W6706
03W6707
03W6708
03W6709
03W6710
03W6691
03W6711
03W6712
03W6713
03W6714
03W6692
03W6715
04T1598
Norwegian
Polish
Portuguese
Russian English
Romanian
Russian
Simplified Chinese
Slovak
Slovenian
Spanish
Serbian-Latin
Traditional Chinese
Turkish
US English
Chapter 10. Parts list 113
Download from Www.Somanuals.com. All Manuals Search And Download.
• 0217-CTO, 23x, 24x, 25x, 27x, 2Bx, 2Cx, 2Dx, 2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx,
2Yx, 33x, 34x, 36x, 3Dx, 3Cx
• 0221-CTO, 23x, 25x, 28x, 29x, 2Lx, 2Mx, 2Nx, 2Px, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 37x
• 0250-CTO
Table 24. Parts list—Windows 7 Professional (64 bit) recovery DVDs
Language
P/N
CRU
ID
Arabic
04T1655
04T1656
04T1682
04T1680
04T1681
04T1679
04T1659
04T1661
04T1662
04T1663
04T1664
04T1665
04T1660
04T1666
04T1667
04T1668
04T1669
04T1670
04T1671
04T1672
04T1657
04T1673
04T1674
04T1675
04T1658
04T1676
04T1678
04T1677
*
Brazilian Portuguese
C&L Croatia (Croatian/Slovenian/English)
C&L EMEA (Dutch/French/German/English)
C&L Hong Kong S.A.R. (Traditional Chinese/Simplified Chinese/English)
C&L Nordics (Danish/Finnish/Swedish/Norwegian/English)
Czech
French
Greek
German
Hebrew
Hungarian
Indian English
Japanese
Korean
Polish
Portuguese
Russian English
Romanian
Russian
Simplified Chinese
Slovak
Spanish
Serbian-Latin
Traditional Chinese
Turkish
US English
US English disable
114 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Common service tools
Table 25. Parts list—Common service tools
Tool
P/N
95F3598
1650840
93F2838
00P6967
08K7159
40Y8687
40Y8704
05K9283
27L3452
42W7820
—
Screwdriver kit
1/4" drive spinner handle
1/4" Sq. to 1/4" hex torx adapter
TR7-TR-10 tamper resistant torx bits
Removal tool antenna RF connector
USB 2.0 CD-RW/DVD-ROM combo drive II
USB cable
USB floppy diskette drive for maintenance diskette
USB floppy diskette drive tool kit
Test card for integrated Smart Card
LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later
Note: Download the file from the following Web site:
http://support.lenovo.com
Chapter 10. Parts list 115
Download from Www.Somanuals.com. All Manuals Search And Download.
116 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult
your local Lenovo representative for information on the products and services currently available in your
area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that
Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service
that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user’s
responsibility to evaluate and verify the operation of any other product, program, or service.
Lenovo may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document does not give you any license to these patents. You can send
license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO GROUP LTD. PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some
jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore,
this statement may not apply to you.
This information could include technical inaccuracies or typographical errors. Changes are periodically
made to the information herein; these changes will be incorporated in new editions of the publication.
Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
The products described in this document are not intended for use in implantation or other life support
applications where malfunction may result in injury or death to persons. The information contained in this
document does not affect or change Lenovo product specifications or warranties. Nothing in this document
shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo
or third parties. All information contained in this document was obtained in specific environments and is
presented as an illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it believes appropriate without
incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in
any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of
the materials for this Lenovo product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled environment. Therefore, the result
obtained in other operating environments may vary significantly. Some measurements may have been
made on development-level systems and there is no guarantee that these measurements will be the same
on generally available systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their
specific environment.
© Copyright Lenovo 2009, 2011
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Trademarks
The following terms are trademarks of Lenovo in the United States, other countries or both:
Active Protection System
Lenovo
ThinkPad
ThinkVantage
TrackPoint
UltraNav
Microsoft and Windows are trademarks or registered trademarks of the Microsoft group of companies.
The following terms are trademarks of Intel Corporation or its subsidiaries in the United States, other
countries, or both.
Intel
Intel Centrino
Intel Core
Other company, product, or service names may be the trademarks or service marks of others.
118 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Number: 63Y0744_03
(1P) P/N: 63Y0744_03
*63Y0744_03*
Download from Www.Somanuals.com. All Manuals Search And Download.
|