Hardware Maintenance Manual
ThinkPad T530, T530i, and W530
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
39
39
40
40
General safety .
1
2
3
Power management
Electrical safety .
Safety inspection guide .
40
40
41
41
42
43
43
44
44
45
45
Sleep mode .
Hibernation mode
Numeric error codes
discharge.
3
4
4
Grounding requirements .
Safety notices (multilingual translations) .
Laser compliance statements (multilingual
translations) .
Error messages
Beep symptoms .
No-beep symptoms .
17
25
25
board
26
26
Supported RAID levels
47
Configuring the system UEFI BIOS to enable
embedded SATA RAID functionality
47
48
48
GAV .
26
26
Deleting RAID volumes
FRU identification for CTO, CMV, and GAV
products .
27
What to do first
29
30
30
30
31
31
32
32
33
33
34
Quick test programs.
UEFI diagnostic program .
Locating computer controls, connectors, and
indicators.
55
55
56
56
56
58
60
61
61
Rear view .
Bootable diagnostic programs.
Bottom view .
Checking operational charging
Major FRUs and CRUs.
Miscellaneous kits and other FRUs .
Restoring the factory contents by using the
product Recovery Disc Set .
35
Retaining serial numbers.
63
64
Windows 8 operating system .
36
38
39
39
Passwords .
unit
64
65
© Copyright Lenovo 2012, 2013
i
Download from Www.Somanuals.com. All Manuals Search And Download.
65
1130 Backup battery .
1150 Speaker assembly .
1160 Thermal fan assembly
89
90
91
92
95
96
99
101
67
1170 Microprocessor .
1180 LCD unit .
W530 .
68
68
1200 I/O sub card
1020 Serial Ultrabay Enhanced device or blank
bezel
69
70
71
72
74
77
78
structure frame
102
106
107
108
1030 Memory module slot cover.
1040 Memory module (bottom slot)
2020 LED sub card .
hinges .
108
112
80
84
85
88
Electronic emission notices.
116
116
ii Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
About this manual
This manual contains service and reference information for the following ThinkPad® products.
ThinkPad T530 and T530i
Machine type (MT) 2359, 2392, 2393, 2394, 2429, 2430, and 2434
ThinkPad W530
MT 2436, 2438, 2439, 2441, 2447, 2449, and 2463
Use this manual along with the advanced diagnostic tests to troubleshoot problems.
Important: This manual is intended only for trained service technicians who are familiar with ThinkPad
products. Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively.
Before servicing a ThinkPad product, be sure to read all the information under and Chapter 2 “Important
© Copyright Lenovo 2012, 2013
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Safety information
This chapter presents the following safety information that you need to be familiar with before you service a
ThinkPad notebook computer.
•
•
•
•
•
•
•
General safety
Follow these rules to ensure general safety:
• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you
think is too heavy for you.
• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
• Before you start the machine, make sure that other service technicians and the customer's personnel are
not in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing
the machine.
• Keep your toolcase away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your
sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, about 8
centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing, because metal
objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device
that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan
louvers or cover them with labels or stickers.
© Copyright Lenovo 2012, 2013
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical safety
Observe the following rules when working on electrical equipment.
Important:
• Use only approved tools and test equipment. Some hand tools have handles covered with a soft material
that does not insulate you when working with live electrical currents.
• Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to
decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical
accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power off the wall box that supplies power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you. That person must be there
to switch off the power, if necessary.
– Use only one hand when working with powered-on electrical equipment; keep the other hand in your
pocket or behind your back.
CAUTION:
An electrical shock can occur only when there is a complete circuit. By observing the above
rule, you may prevent a current from passing through your body.
– When using testers, set the controls correctly and use the approved probe leads and accessories for
that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as
metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages. Instructions for these
precautions are in the safety sections of maintenance information. Use extreme care when measuring
high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.
• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
nongrounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
– Units similar to those listed above
This practice ensures correct grounding of the units.
2
Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
• If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each
machine was designed and built, required safety items were installed to protect users and service technicians
from injury. This guide addresses only those items. You should use good judgment to identify potential
safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock)
• Explosive hazards, such as a damaged CRT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware
To determine whether there are any potentially unsafe conditions, use the following checklist at the beginning
of every service task. Begin the checks with the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Turn off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground
continuity for 0.1 ohm or less between the external ground pin and the frame ground.
b. The power cord should be the authorized type specified for your computer on the Web page
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-ThinkPad alterations. Use good judgment as to the safety of any
non-ThinkPad alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.
Chapter 1. Safety information
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when
handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.
Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
– When working on a double-insulated or battery-operated system, use an ESD common ground or
reference point. You can use coax or connector-outside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a certified electrician.
Safety notices (multilingual translations)
The safety notices in this section are provided in the following languages:
• English
• Arabic
• German
• Hebrew
• Japanese
• Korean
• Spanish
DANGER
4
Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
DANGER
DANGER
DANGER
DANGER
DANGER
DANGER
Chapter 1. Safety information
Download from Www.Somanuals.com. All Manuals Search And Download.
5
PERIGO
PERIGO
PERIGO
PERIGO
PERIGO
8
Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
VORSICHT
VORSICHT
VORSICHT
VORSICHT
VORSICHT
VORSICHT
Chapter 1. Safety information 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Laser compliance statements (multilingual translations)
The laser compliance statements in this section are provided in the following languages:
• English
• Arabic
• German
• Hebrew
• Japanese
• Korean
• Spanish
Chapter 1. Safety information 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Important service information
This chapter presents the following important service information that applies to all machine types supported
by this manual:
•
–
–
–
“Strategy for replacing a hard disk drive, a solid state drive, or an mSATA solid state drive” on page 25
•
–
–
Important:
• Advise customers to contact the Lenovo® Customer Support Center if they need any assistance in
obtaining or installing any software fixes, drivers, and UEFI BIOS downloads. Telephone numbers for
Lenovo Support are available at:
• System disassembly and reassembly videos that show the FRU removal or replacement procedures for
the Lenovo authorized service technicians are available at:
Strategy for replacing FRUs
Before replacing parts:
Make sure that all software fixes, drivers, and UEFI BIOS downloads are installed before replacing any
FRUs listed in this manual.
After a system board is replaced, ensure that the latest UEFI BIOS is loaded to the system board before
completing the service action.
To download and install software fixes, drivers, and UEFI BIOS, go to http://www.lenovo.com/ThinkPadDrivers
and follow the instructions on the screen.
Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs:
• If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the
original FRU before you continue.
• Some computers have both a processor board and a system board. If you are instructed to replace either
the processor board or the system board, and replacing one of them does not correct the problem,
reinstall that board, and then replace the other one.
• If an adapter or a device consists of more than one FRU, any of the FRUs might be the cause of the error.
Before replacing the adapter or device, remove the FRUs, one by one, to see if the symptoms change.
Replace only the FRU that changed the symptoms.
Strategy for replacing a hard disk drive, a solid state drive, or an mSATA
solid state drive
Always try to run a low-level format operation before replacing a hard disk drive or a solid state drive. This
will cause all customer data on the hard disk drive or solid state drive to be lost. Be sure that the customer
has a current backup of the data before you perform this task.
© Copyright Lenovo 2012, 2013
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Attention: The drive startup sequence in the computer you are servicing might have been changed. Be
extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect
drive, data or programs can be overwritten.
If the computer is shipped with both an mSATA solid state drive and a hard disk drive, the mSATA solid state
drive is used for the “cache” function and to support the Intel® Rapid Start Technology. We recommend that
users do not replace the mSATA solid-state drive by themselves. Otherwise, the “cache” function will not
work and the Intel Rapid Start Technology cannot be used any more.
Attention: Ensure that you partition the mSATA solid-state drive after installing it on the computer you are
servicing. Otherwise, the mSATA solid-state drive will not function correctly. For instructions on how to
Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper handling of a system board can
cause damage to those components, and may cause a system malfunction.
Attention: When handling a system board:
• Do not drop a system board or apply any excessive force to it.
• Avoid rough handling of any kind.
• Avoid bending a system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset.
How to use error codes
Use the error codes displayed on the screen to diagnose failures. If more than one error code is displayed,
begin the diagnosis with the first error code. Whatever causes the first error code may also cause false error
codes. If no error code is displayed, see whether the error symptom is listed in the Symptom-to-FRU
Index for the computer you are servicing.
Strategy for replacing FRUs for CTO, CMV, and GAV
Product definition
Dynamic Configure To Order (CTO)
This provides the ability for a customer to configure a Lenovo solution from an eSite, and have this
configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label and
eSupport will load these products as the 4-digit MT and 3-digit model, where model = “CTO” (Example:
1829-CTO).
Custom Model Variant (CMV)
This is a unique configuration that has been negotiated between Lenovo and the customer. A unique 4-digit
MT and 3-digit model is provided to the customer to place orders (Example: 1829-W15). A CMV is a special
bid offering. Therefore, it is NOT generally announced.
• The MTM portion of the machine label is the 4-digit MT and 3-digit model, where model = “CTO”
(Example: 1829-CTO). The PRODUCT ID portion of the machine label is the 4-digit MT and 3-digit CMV
model (Example: 1829-W15).
• eSupport will show both the CTO and CMV machine type models (Example: 1829-CTO and 1829-W15
will be found on the eSupport site.)
26 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
General Announce Variant (GAV)
This is a standard model (fixed configuration). GAVs are announced and offered to all customers. The MTM
portion of the machine label is a 4-digit MT and 3-digit model, where model = a “fixed part number”, not
“CTO” (Example: 1829-F1U). Also, eSupport will list these products under the same fixed model number.
FRU identification for CTO, CMV, and GAV products
Use Lenovo eSupport to identify major FRUs, FRU part numbers, and FRU descriptions for CTO, CMV, and
GAV products at an MT - serial number level. Examples of major FRUs are hard disk drive, system board,
liquid crystal display (LCD), and memory module. All CTO and CMV products are loaded under the 4-digit
MT and 3-digit model, where model = “CTO” (example: 1829-CTO). GAVs are loaded under the 4-digit MT
and 3-digit model, where model = a “fixed part number”, not “CTO” (example: 1829-F1U).
To identify the major FRUs for a product, do the following:
1. Go to:
2. Click Warranty & Services.
3. Click Check Warranty Status.
4. On the Warranty Status Lookup page, click Parts Lookup.
5. Type your machine type and serial number, and then click Submit.
eSupport also can be used to view the general FRU list for a product.
To get the general FRU list for a product, do the following:
1. Go to:
2. Click Parts & Accessories.
3. Follow the instructions on the screen to select product.
4. Click Products and Parts Detail.
5. On the PRODUCT AND PARTS DETAIL page, click the Parts Detail tab to view the FRU list.
Note: The FRU list is a general list of components and does not contain specific model information.
Chapter 2. Important service information 27
Download from Www.Somanuals.com. All Manuals Search And Download.
28 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. General checkout
This chapter presents following information:
•
•
•
Before you go to the checkout guide, be sure to read the following important notes.
Important:
• Only certified trained personnel should service the computer.
• Before replacing any FRU, read the entire page on removing and replacing FRUs.
• When you replace FRUs, it is recommended to use new nylon-coated screws.
• Be extremely careful during such write operations as copying, saving, or formatting. Drives in the
computer that you are servicing sequence might have been altered. If you select an incorrect drive,
data or programs might be overwritten.
• Replace a FRU only with another FRU of the correct model. When you replace a FRU, make sure that
the model of the machine and the FRU part number are correct by referring to the FRU parts list on the
• A FRU should not be replaced because of a single, unreproducible failure. Single failures can occur
for a variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation,
electrostatic discharge, or software errors. Consider replacing a FRU only when a problem recurs. If you
suspect that a FRU is defective, clear the error log and run the test again. If the error does not recur, do
not replace the FRU.
• Be careful not to replace a nondefective FRU.
What to do first
When you return a FRU, you must include the following information in the parts exchange form or parts
return form that you attach to it:
1. Name and phone number of service technician
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Failure symptoms, error codes appearing on the display, and beep symptoms
6. Procedure index and page number in which the failing FRU was detected
7. Failing FRU name and part number
8. Machine type, model number, and serial number
9. Customer's name and address
Note: During the warranty period, the customer may be responsible for repair costs if the computer damage
was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper
maintenance by the customer. Following is a list of some common items that are not covered under warranty
and some symptoms that might indicate that the system was subject to stress beyond normal use.
Before checking problems with the computer, determine whether the damage is covered under the warranty
by referring to the following list:
The following are not covered under warranty:
• LCD panel cracked from the application of excessive force or from being dropped
• Scratched (cosmetic) parts
© Copyright Lenovo 2012, 2013
29
Download from Www.Somanuals.com. All Manuals Search And Download.
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force
• Damage caused by liquid spilled into the system
• Damage caused by the improper insertion of a PC Card or the installation of an incompatible card
• Improper disc insertion or use of an optical drive
• Fuses blown by attachment of a nonsupported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect ac power adapter on laptop products
The following symptoms might indicate damage caused by nonwarranted activities:
• Missing parts might be a symptom of unauthorized service or modification.
• Check for obvious damage to a hard disk drive. If the spindle of a hard disk drive becomes noisy, the hard
disk drive might have been dropped or subject to excessive force.
Checkout guide
Use the following procedures as a guide in identifying and correcting problems with the ThinkPad notebook
computer.
Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products,
prototype cards, or modified options can lead to false indications of errors and invalid system responses.
1. Identify the failing symptoms in as much detail as possible.
2. Verify the symptoms. Try to re-create the failure by running the diagnostic test or by repeating the
operation.
Lenovo Solution Center
The Lenovo Solution Center program enables you to troubleshoot and resolve computer problems. It
combines diagnostic tests, system information collection, security status, and support information, along
with hints and tips for maximum system performance.
To run the Lenovo Solution Center program, go to Control Panel and click System and Security ➙ Lenovo -
System Health and Diagnostics, and then follow the instructions on the screen.
For more information about the Lenovo Solution Center program, refer to the help information system
of the program.
Quick test programs
You can run quick test programs to troubleshoot and resolve computer problems, especially when the
computer does not have the Lenovo Solution Center program installed.
Lenovo provides the following quick test programs:
• Lenovo Hard Drive Quick Test: Use this program to troubleshoot and resolve internal storage problems.
• Lenovo Memory Quick Test: Use this program to troubleshoot and resolve memory module problems.
The quick test programs are applicable on the following operating systems:
• Microsoft® Windows®
• Microsoft Windows 7
8
• Microsoft Windows XP
30 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
• Microsoft Windows Server® 2003
• Microsoft Windows Server 2008
To download and install a quick test program, go to http://www.lenovo.com/diags and follow the instructions
on the Web site.
To run a test using a quick test program, do the following:
1. Go to the C:\SWTOOLS\ldiag directory.
2. Double-click the gui_lsc_lite.exe file.
3. When the User Account Control window opens, click Yes.
4. Select the device class to be tested.
5. Select the devices to be tested.
6. Select the test to be performed.
7. Follow the instructions on the screen to start the test. When a problem is detected, information
messages are displayed. Refer to the messages to troubleshoot the problem.
UEFI diagnostic program
A UEFI diagnostic program is preinstalled on the computer. It enables you to test memory modules and
internal storage devices, view system information, and check and recover bad sectors on internal storage
devices.
To run the UEFI diagnostic program, do the following:
32, and check the power sources. If an error code is displayed, go to for error code descriptions and
troubleshooting hints.
2. When the ThinkPad logo is displayed, repeatedly press and release the F10 key. The main screen of the
UEFI diagnostic program is displayed.
3. Follow the instructions on the screen to use the program.
The options on the main screen are as follows:
Table 1. Items on the main screen of the UEFI diagnostic program
Tests
Tools
• Quick Memory Test
• Quick Storage Device Test
• Exit Application
• System Information
• Recover Bad Sectors Tool
Bootable diagnostic programs
If the computer you are servicing is not installed with the UEFI diagnostic program, you can download a
bootable diagnostic program from the Lenovo Support Web site. The bootable diagnostic programs enable
you to test computer memory and internal storage devices, view system information, and check and recover
the internal storage devices. To use the bootable diagnostic programs, you can create a bootable diagnostic
medium on a USB device or CD.
To create a bootable diagnostic medium, do the following:
2. Click Lenovo Bootable Diagnostics.
Chapter 3. General checkout 31
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Follow the instructions on the Web site to create a bootable diagnostic medium on a USB device or CD.
To use the diagnostic medium you have created, do one of the following:
• If you have created the bootable diagnostic medium on a USB device, do the following:
1. Attach the USB device to the computer.
32, and check the power sources. If an error code is displayed, go to for error code descriptions
and troubleshooting hints.
3. When the ThinkPad logo is displayed, repeatedly press and release the F12 key. When the Boot
Menu window opens, release the F12 key.
4. Use the arrow keys to select USB HDD and then press Enter. The diagnostic program will be
launched automatically.
5. Follow the instructions on the screen to use the diagnostic program.
• If you have created the bootable diagnostic medium on a CD, do the following:
32, and check the power sources. If an error code is displayed, go to for error code descriptions
and troubleshooting hints.
2. Insert the CD into the optical drive.
3. Restart the computer.
4. When the ThinkPad logo is displayed, repeatedly press and release the F12 key. When the Boot
Menu window opens, release the F12 key.
5. Use the arrow keys to select ATAPI CDx (x: 0, 1, ...) and then press Enter. The diagnostic program
will be launched automatically.
6. Follow the instructions on the screen to use the diagnostic program.
Power system checkout
To verify a symptom, do the following:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the ac adapter.
4. Check that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the ac adapter and install the charged battery pack.
7. Check that the battery pack supplies power when you turn on the computer.
If you suspect a power problem, see the appropriate one of the following power supply checkouts:
•
•
•
•
Checking the ac power adapter
If you computer fails only when the ac power adapter is used, use the instructions in this topic.
• If the power problem occurs only when the docking station or the port replicator is used, replace the
docking station or the port replicator.
• If the power-on indicator does not turn on, check the power cord of the ac power adapter for correct
continuity and installation.
32 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
• If the computer does not charge during operation, go to “Checking operational charging” on page 33.
To check the ac adapter, do the following:
1. Unplug the ac adapter cable from the computer.
2. Measure the output voltage at the plug of the ac adapter cable. See the following illustration:
Pin
1
Voltage (V dc)
+20
0
3
2
2
3
Ground
1
(20V)
Note: Output voltage across pin 2 of the ac power adapter might differ from the one you are servicing.
3. If the voltage is not correct, replace the ac adapter.
4. If the voltage is acceptable, replace the system board.
Note: Noise from the ac adapter does not always indicate a defect.
Checking operational charging
To check whether the battery charges correctly during operation, do the following:
Note: Before you begin, install a discharged battery pack or a battery pack that has less than 50% of the
total power remaining in the computer.
1. If the battery status indicator does not turn on, remove the battery pack and let it return to room
temperature.
2. Reinstall the battery pack.
3. If the indicator still does not turn on, replace the battery pack.
4. If the indicator still does not turn on, replace the system board. Otherwise, refer to Checking the battery
pack to check the original battery pack.
Checking the battery pack
The battery status icon in the Windows notification area displays the percentage of battery power remaining.
To check for detailed battery status information, do the following:
• For Windows 7: Open the Power Manager program and click the Battery tab.
• For Windows 8: Open the Lenovo Support program and click Battery Health, or open the Lenovo
Settings program and click Power.
Note: If the battery pack becomes hot, it may not be able to charge. Remove it from the computer and leave
it at room temperature for a while. After it cools down, reinstall and recharge it.
To check the battery pack, do the following:
1. Turn off the computer and disconnect the ac power adapter.
2. Remove the battery pack and measure the voltage between battery terminals 1 (+) and 7 (-). The
correct voltage are shown in the following table.
Chapter 3. General checkout 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminal
Voltage (V dc)
+ 0 to + 12.6
Ground (-)
1
7
7(-)
6(-)
5
4
3
2(+)
1(+)
3. Measure the resistance between battery terminals 5 and 7. The resistance must be 4 to 30 K Ω. If the
resistance is not correct, replace the battery pack.
4. Depending on the voltage that you measure, do one of the following:
• If the voltage is less than +11.0 V dc, recharge the battery pack. If the voltage is still less than +11.0 V
dc after recharging, replace the battery pack.
• If the voltage is more than +11.0 V dc, discharge the battery pack until the voltage becomes less
than +11.0 V dc and then recharge the battery pack. If the voltage still is less than +11.0 V dc after
recharging, replace the battery pack.
Note: Recharging will take at least three hours, even if the battery status indicator does not turn on.
5. Replace the system board if the new battery pack is not charged.
Checking the backup battery
Do the following:
1. Power off the computer, and unplug the ac adapter from it.
2. Turn the computer upside down.
5. Measure the voltage of the backup battery. See the following illustration.
Wire
Red
Voltage (V dc)
+2.5 to +3.2
Ground
Black
• If the voltage is correct, replace the system board.
• If the voltage is not correct, replace the backup battery.
• If the backup battery discharges quickly after replacement, replace the system board.
34 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Related service information
This chapter presents following information:
•
•
•
•
Service Web site:
When the latest maintenance diskette and the system program service diskette become available, they
Restoring the factory contents by using the product Recovery Disc Set
When the main storage device is replaced because of a failure, no product recovery program is on the new
drive. In this case, the customer must use the Recovery Disc Set to recover the tablet. Order the Recovery
Disc Set and the drive at the same time so that the customer can restore the tablet to the factory default
settings by using the Recovery Disc Set after the new drive is installed. For information about which discs to
order, go to:
Depending on the model, the number of recovery discs included in the Recovery Disc Set differs. To restore
the factory contents by using the product Recovery Disc Set, do the following:
Notes:
• During the recovery process, all data on the drive will be deleted. If possible, copy any important data
or personal files that you want to keep onto removable media or a network drive before you start the
recovery process.
• The recovery process takes one to two hours to complete. The length of time depends on the method you
use. If you use product Recovery Disc Set, the recovery process takes about two hours.
1. Connect an external CD/DVD drive.
2. Make the CD/DVD drive the first startup device in the startup sequence using the following procedure:
a. Open the ThinkPad Setup program and select Startup ➙ Boot.
b. Select the CD/DVD drive as the 1st Boot Device.
3. Insert the bootable recovery disc into the CD/DVD drive.
4. Start the computer from the external CD/DVD drive.
5. When promoted, select your language and click Next.
6. Read the license and accept the terms and conditions. Then follow the instructions on the screen.
7. If the Recovery Disc Set contains a Supplemental Recovery Disc, insert it when prompted and click Yes.
Note: Not all Recovery Disc Sets come with a Supplemental Recovery Disc. If there is a Supplemental
Recovery Disc, it will be clearly marked as such.
8. When all of the data has been copied from the last disc in the set and has been processed, remove
the external CD/DVD drive and restart the computer. Follow the instructions on the screen to finish
the recovery.
Note: The rest of the recovery process is fully automated and no action from you is required. The
computer will restart into the Microsoft Windows desktop several times and you might experience
periods when no activity is apparent on the screen for several minutes at a time. This is normal.
© Copyright Lenovo 2012, 2013
35
Download from Www.Somanuals.com. All Manuals Search And Download.
9. When the recovery process completes, the Welcome to Microsoft Windows screen is displayed. Follow
the instructions on the screen to complete the Windows setup.
10. After you have completed the Windows setup, you might want to restore the original startup sequence.
Start the ThinkPad Setup program and then press F9 to restore the default settings. Press F10 to save
changes and exit the ThinkPad Setup program.
Note: After restoring a drive to the factory default settings, you might need to reinstall some device drivers.
Using the Windows recovery programs on the Windows 8 operating
system
This section provides information about the recovery solutions for the Windows 8 operating system.
A Windows recovery image is preinstalled in the recovery partition on your computer. The Windows recovery
image enables you to refresh your computer, or reset your computer to the factory default settings.
You can create recovery media as backups or replacement for the Windows recovery image. With the
recovery media, you can troubleshoot and fix the problems on your computer even if you cannot start the
Windows 8 operating system. It is recommended that you create recovery media as early as possible. For
Refreshing the computer
If your computer does not perform well and the problem might be caused by a recently installed program,
you can refresh your computer without losing your personal files or changing your settings.
Attention: If you refresh your computer, the programs that came with your computer and the programs that
you installed from Windows Store will be reinstalled, but all other programs will be removed.
To refresh your computer, do the following:
1. Move your cursor to the top-right or bottom-right corner of the screen to display the charms. Click
Settings ➙ Change PC settings ➙ General.
2. In the Refresh your PC without affecting your files section, click Get started.
3. Follow the instructions on the screen to refresh your computer.
Resetting the computer to the factory default settings
If you want to recycle your computer or just start over, you can reset your computer to the factory default
settings. Resetting the computer will reinstall the operating system, reinstall all the programs that came with
your computer, and reset all the settings to the factory default settings.
Attention: If you reset the computer to the factory default settings, all your personal files and settings will be
deleted. To avoid data loss, make a backup copy of all the data that you want to keep.
To reset your computer to the factory default settings, do the following:
1. Move your cursor to the top-right or bottom-right corner of the screen to display the charms. Click
Settings ➙ Change PC settings ➙ General.
2. In the Remove everything and reinstall Windows section, click Get started. Then click Next to
confirm the operation.
3. Depending on your needs, do one of the following:
• To perform a quick format, click Just remove my files to start the process. The process will take
several minutes.
36 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
• To perform a complete format, click Fully clean the drive to start the process. The process will
take several hours.
4. Follow the instructions on the screen to reset your computer to the factory default settings.
Using the advanced startup options
With the advanced startup options, you can change the firmware settings of the computer, change the
startup settings of the Windows operating system, start the computer from an external device, or restore the
Windows operating system from a system image.
To use the advanced startup options, do the following:
1. Move your cursor to the top-right or bottom-right corner of the screen to display the charms. Click
Settings ➙ Change PC settings ➙ General.
2. In the Advanced startup section, click Restart now ➙ Troubleshoot ➙ Advanced options.
3. Select a desired startup option, then follow the instructions on the screen.
Recovering your computer from the Windows recovery environment
The Windows recovery environment on your computer operates independently from the Windows 8
operating system. If the Windows 8 operating system fails to start, you still can use the Windows recovery
environment to troubleshoot and fix problems.
The Windows recovery environment starts automatically in the case of two consecutive failed boots.
To manually start the Windows recovery environment, turn on or restart the computer. Before the Windows 8
operating system starts, repeatedly press the F11 key. The Windows recovery environment starts.
To use the Windows recovery environment, do the following:
Note: Ensure that your computer is connected to ac power.
1. Select a preferred language and then select a preferred keyboard layout.
2. Click Troubleshoot to display the optional recovery solutions.
3. Select a corresponding recovery solution according to your situation. For example, select Reset your
PC if you want to reset your computer to the factory default settings.
Creating and using recovery media
You can create recovery media as backups for the Windows recovery environment and the Windows
recovery image. If you cannot start the computer, you can use recovery media to troubleshoot and fix the
problems on your computer.
It is recommended that you create recovery media as early as possible. Once you create recovery media,
keep them in a safe place and do not use them to store other data.
Creating recovery media
To create recovery media, you need a USB drive with at least 8 GB of storage. The required USB capacity
depends on the size of the recovery image.
Attention: Creating recovery media will delete anything stored on the USB drive. To avoid data loss, make a
backup copy of all the data that you want to keep.
To create recovery media, do the following:
Note: Ensure that your computer is connected to ac power.
Chapter 4. Related service information 37
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Move your cursor to the top-right or bottom-right corner of the screen to display the charms, and
click Search.
2. Type recovery in the Search field and click Settings. Then click Create a recovery drive.
3. Click Yes in the User Account Control window to allow the Recovery Media Creator program to start.
4. Ensure that you select the Copy the recovery partition from the PC to the recovery drive. option.
Then click Next.
Important: If you clear the Copy the recovery partition from the PC to the recovery drive. option,
you will create recovery media without the recovery partition content. You still can start the computer
from the recovery media, but you might be unable to recover your computer if the recovery partition on
your computer is damaged.
5. Connect a proper USB drive then click Next.
6. Click Create in the Recovery Drive window. The creation of the recovery media starts.
7. When the creation of the recovery media finishes, do one of the following:
• To keep the recovery partition on your computer, click Finish.
• To delete the recovery partition on your computer, click Delete the recovery partition.
Attention: If you delete the recovery partition on your computer, do keep the recovery media in a
safe place. The Windows recovery image will not be stored in your computer anymore, and you will
need the recovery media to refresh or reset your computer.
8. Remove the USB drive. The recovery media are created successfully.
Using recovery media
If you cannot start your computer, or if you cannot start the Windows recovery image on your computer, use
recovery media to recover your computer.
To use recovery media, do the following:
Note: Ensure that your computer is connected to ac power.
1. Turn on or restart the computer. Before the Windows operating system starts, repeatedly press the F12
key. The Boot Menu window opens.
2. Select the recovery drive as the boot device.
3. Select a preferred language and then select a preferred keyboard layout.
4. Click Troubleshoot to display the optional recovery solutions.
5. Select a corresponding recovery solution according to your situation. For example, select Reset your
PC if you want to reset your computer to the factory default settings.
For more information about the recovery solutions provided by the Windows 8 operating system, go to:
Passwords
As many as three passwords might be needed for a ThinkPad notebook computer: the power-on password,
the hard disk password, and the supervisor password.
If any of these passwords has been set, a prompt for it will be displayed on the screen whenever the
computer is turned on. The computer does not start until the password is entered.
Note: If only a supervisor password is set, the password prompt will not be displayed when the operating
system is started.
38 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Power-on password
A power-on password (POP) protects the system from being powered on by an unauthorized person. The
password must be entered before an operating system can be booted. For how to remove the POP, see
Hard disk password
There are two hard disk passwords:
• User hard disk password - for the user
• Master hard disk password - for the system administrator, who can use it to get access to the hard disk
even if the user has changed the user hard disk password.
Note: There are two modes for the hard disk password: User only and Master + User. The Master + User
mode requires two hard disk passwords; the system administrator enters both in the same operation. The
system administrator then provides the user hard disk password to the system user.
Attention: If the user hard disk password has been forgotten, check whether a master hard disk password
has been set. If a master hard disk password has been set, it can be used to access the hard disk drive. If
no master hard disk password is available, neither Lenovo nor Lenovo authorized service technicians provide
any services to reset either the user hard disk password or the master hard disk password, or to recover data
from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.
For instructions on how to remove the hard disk password, see “How to remove the hard disk password”
on page 40.
Supervisor password
A supervisor password protects the system information stored in the ThinkPad Setup program. The user
must enter the supervisor password in order to get access to the ThinkPad Setup program and change the
system configuration.
Attention: If the supervisor password has been forgotten and cannot be made available to the service
technician, there is no service procedure to reset the password. The system board must be replaced for
a scheduled fee.
How to remove the power-on password
To remove the power-on password that you have forgotten, do one of the following:
(A) If no supervisor password has been set, do the following to remove the power-on password:
1. Turn off the computer and disconnect the ac power adapter.
4. Connect the ac power adapter. Turn on the computer and wait until the POST ends. After the POST
ends, the password prompt does not appear. The POP has been removed.
5. Reinstall the backup battery and the battery pack.
(B) If a supervisor password has been set and is known to the service technician, do the following to remove
the power-on password:
1. Turn on the computer.
2. When the ThinkPad logo is displayed, immediately press F1.
3. Type the supervisor password to enter the ThinkPad Setup program.
Chapter 4. Related service information 39
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Select Security.
5. Select Password.
6. Select Power-On Password.
7. Type the current supervisor password in the Enter Current Password field. Then leave the Enter
New Password field blank, and press Enter twice.
8. In the Changes have been saved window, press Enter.
9. Press F10 to save changes and exit the ThinkPad Setup program.
How to remove the hard disk password
Attention: If User only mode is selected and the user hard disk password has been forgotten and cannot be
made available to the service technician, neither Lenovo nor Lenovo authorized service technicians provide
any services to reset the user hard disk password, or to recover data from the hard disk drive. To put the
system back to operational status, the only Lenovo and Lenovo-authorized service solution would be to
replace the hard disk drive or solid-state drive with a scheduled fee.
To remove a user hard disk password that has been forgotten, when the supervisor password and the master
hard disk password are known, do the following:
1. Turn on the computer.
2. When the ThinkPad logo is displayed, immediately press F1 to enter the ThinkPad Setup program.
3. Select Security.
4. Select Password.
5. Select Hard-disk x password where x is the letter of the hard disk drive. A pop-up window opens.
6. Select Master HDP, where HDP stands for hard disk password.
7. Type the current master hard disk password in the Enter Current Password field. Then, leave the Enter
New Password field blank, and press Enter twice.
8. Press F10 to save changes and exit the ThinkPad Setup program. The user hard disk password and the
master hard disk password have been removed.
Power management
To reduce power consumption, the computer has three power management modes: screen blank, sleep,
and hibernation.
Screen blank mode (for the Windows 7 operating system only)
If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off.
To put the computer into screen blank mode, right-click the battery gauge from the Windows notification
area and select Power off display.
To end screen blank mode and resume normal operation, press any key.
Sleep mode
When the computer enters sleep mode, the following events occur in addition to what occurs in screen
blank mode:
• The LCD is powered off.
• The hard disk drive is powered off.
• The microprocessor stops.
To enter sleep mode, press Fn+F4.
40 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
In certain circumstances, the computer goes into sleep mode automatically:
• After a period of inactivity specified in power plan settings
• When the battery indicator blinks orange, indicating that the battery power is low
To cause the computer to return from sleep mode and resume operation, do one of the following:
• Press the Fn key.
• Open the LCD cover.
• Turn on the power button.
Also, in either of the following events, the computer automatically returns from sleep mode and resumes
operation:
• The ring indicator (RI) is signaled by a serial device or a PC Card device.
• The time set on the resume timer elapses.
Note: The computer does not accept any input immediately after it enters sleep mode. Wait a few
seconds before taking any action to reenter operation mode.
Hibernation mode
In hibernation mode, the following occurs:
• The system status, RAM, VRAM, and setup data are stored on the hard disk.
• The system is powered off.
Note: If the computer enters the hibernation mode while it is docked to the docking station, do not undock it
before resuming normal operation. If you do undock it and then try to resume normal operation, you will get
an error message, and you will have to restart the system.
To put the computer into hibernation mode, use the Power Manager program to define one of the following
actions as the event that causes the system to go into hibernation mode. Then perform the defined action.
• Closing the lid.
• Pressing the power button.
• Pressing Fn+F4.
Also, the computer goes into hibernation mode automatically after a period of inactivity specified in power
plan settings
When the power is turned on, the computer returns from hibernation mode and resumes operation. The
hibernation file in the boot record on the hard disk drive is read, and system status is restored from the
hard disk drive.
Symptom-to-FRU index
This section contains following information:
•
•
•
•
•
•
•
The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most
likely cause is listed first, in boldface type.
Chapter 4. Related service information 41
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Do the FRU replacement or other actions in the sequence shown in the column headed “FRU or
action, in sequence.” If replacing a FRU does not solve the problem, put the original part back in the
computer. Do not replace a nondefective FRU.
This index can also help you determine, during regular servicing, what FRUs are likely to need to be
replaced next.
A numeric error is displayed for each error detected in POST or system operation. In the displays, n can
be any number.
If no numeric code is displayed, check the narrative descriptions of symptoms. If the symptom is not
Note: For a device not supported by diagnostic codes in the ThinkPad notebook computers, see the
manual for that device.
Numeric error codes
Table 2. Numeric error codes
FRU or action, in sequence
System board
Symptom or error
0177: Bad SVP data, stop POST task. — The checksum
of the supervisor password in the EEPROM is not correct.
0183: Bad CRC of Security Settings in EFI Variable.
Enter ThinkPad Setup. — The checksum of the Security
settings in the EFI Variable is not correct.
Enter ThinkPad Setup to correct Security settings in
the EFI Variable.
0187: EAIA data access error.
System board
System board
0188: Invalid RFID Serialization Information Area. — The
EEPROM checksum is not correct (Block #0,1).
0189: Invalid RFID configuration Information Area. — The System board
EEPROM checksum is not correct (Block #4,5).
0190: Critical low-battery error
• Charge the battery pack.
• Battery pack
0191: System Security - Invalid Remote Change
requested.
• Run ThinkPad Setup, and then save the current
setting by pressing F10.
• System board
0199: System Security - Security password retry count
exceeded.
• Run ThinkPad Setup, and then save the current
setting by pressing F10.
• System board
0251: System CMOS checksum bad - Default
configuration used
1. Charge the backup battery for more than 8 hours
by connecting the ac adapter.
2. Replace the backup battery and run ThinkPad Setup
to reset the time and date.
0253: EFI Variable Block Data was destroyed.
0271: Real-Time Clock Error. Check Date and Time
settings.
Run ThinkPad Setup to reset the time and date.
1802: Unauthorized network card is plugged in - Power
off and remove the mini PCI network card.
• Remove Mini PCI network card.
• System board
1820: More than one external fingerprint reader is
attached. Power off and remove all but the reader that
you set up within your main operating system.
Remove all but the reader that you set up for the
authentication.
42 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 2. Numeric error codes (continued)
FRU or action, in sequence
System board
Symptom or error
2000: ThinkVantage® Active Protection sensor diagnostics
failed.
1. Reseat the hard disk drive.
2. Main hard disk drive
3. System board
2100: Detection error on HDD0 (Main HDD)
2101: Detection error on HDD1 (Ultrabay HDD)
2102: Detection error on HDD2 (Mini SATA)
2110: Read error on HDD0 (Main HDD)
2111: Read error on HDD1 (Ultrabay HDD)
2112: Read error on HDD2 (Mini SATA)
1. Reseat the hard disk drive.
2. Ultrabay® hard disk drive
3. System board
1. Reseat the Mini SATA device.
2. Mini SATA device
3. System board
1. Reseat the hard disk drive.
2. Main hard disk drive
3. System board
1. Reseat the hard disk drive.
2. Ultrabay hard disk drive
3. System board
1. Reseat the Mini SATA device.
2. Mini SATA device
3. System board
2200: Machine Type and Serial Number are invalid.
2201: Machine UUID is invalid.
System board
System board
Error messages
Table 3. Error messages
Symptom or error
Fan error.
FRU or action, in sequence
1. Fan
2. Thermal grease
3. System board
Thermal sensing error.
System board
The battery installed is not supported by this system
and will not charge. Please replace the battery with the
correct Lenovo battery for this system. Press the ESC
key to continue.
Replace the battery.
Beep symptoms
Table 4. Beep symptoms
FRU or action, in sequence
System board
Symptom or error
Four cycles of four short beeps
Five short beeps, pause, and five more short beeps
System board
1. Memory module
2. System board
One short beep, pause, three short beeps, pause, three
more short beeps, pause, and one short beep
Three short beeps, pause, one short beep, pause, one
more short beep, pause, and three short beeps
Remove the installed PCI devices.
Chapter 4. Related service information 43
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4. Beep symptoms (continued)
Symptom or error
FRU or action, in sequence
System board
Five short beeps
One long and two short beeps
System board
No-beep symptoms
Table 5. No-beep symptoms
Symptom or error
FRU or action, in sequence
1. Make sure that every connector is connected
tightly and correctly.
No beep, power-on indicator on, LCD blank, and no
POST.
2. Memory module
3. System board
1. Reseat the memory module.
No beep, power-on indicator on, and LCD blank during
POST.
2. System board
The power-on password prompt appears.
The hard-disk password prompt appears.
A power-on password or a supervisor password is set.
Type the password and press Enter.
A hard-disk password is set. Type the password and
press Enter.
LCD-related symptoms
Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The
presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT
LCD technology, but excessive pixel problems can cause viewing concerns. If the LCD you are servicing has
two or less visible defective pixels, it should not be considered faulty. However, if the LCD has three or more
visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced.
Notes:
• This policy applies to all ThinkPad notebook computers purchased on 1 January, 2008 or later.
• Lenovo will not provide warranty replacement if the LCD is within specifications because we cannot
guarantee that any replacement LCD will have zero pixel defects.
• One pixel consists of R, G, B sub-pixels.
Table 6. LCD-related symptoms
FRU or action, in sequence
Symptom or error
No beep, power-on indicator on, and a blank LCD during System board
POST.
• LCD backlight not working
• LCD too dark
• LCD brightness cannot be adjusted.
• LCD contrast cannot be adjusted.
1. Reseat the LCD connectors.
2. LCD assembly
3. System board
• LCD screen unreadable
• Characters missing pixels
• Screen abnormal
1. See important note for “LCD-related symptoms.”
2. Reseat all LCD connectors.
3. LCD assembly
• Wrong color displayed
4. System board
Horizontal or vertical lines displayed on LCD
LCD assembly
44 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Intermittent problems
Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware
defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be
considered only when a problem recurs.
Undetermined problems
If the diagnostic tests did not identify the device that has failed, if wrong devices are installed, or if the
system simply is not operating, follow these procedures to isolate the failing FRU (do not isolate FRUs
that have no defects).
Verify that all attached devices are supported by the computer.
Verify that the power supply being used at the time of the failure is operating correctly. (See “Power system
1. Turn off the computer.
2. Visually check each FRU for damage. Replace any damaged FRU.
3. Remove or disconnect all of the following devices:
a. Non-ThinkPad devices
b. Devices attached to the docking station or the port replicator
c. Printer, mouse, and other external devices
d. Battery pack
e. Hard disk drive or solid state drive
f. External drive or optical drive
g. Memory module (Remove all and then install only one memory module)
h. Optical disk
i. PC Cards
4. Turn on the computer.
5. Determine whether the problem has been solved.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRUs one at a time (do not replace a nondefective FRU):
a. System board
b. LCD assembly
Chapter 4. Related service information 45
Download from Www.Somanuals.com. All Manuals Search And Download.
46 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Installing and configuring RAID
This chapter contains the following topics:
•
•
•
•
Note: When the UEFI BIOS was formatted or the system board was replaced in the RAID-supported models,
RAID is enabled by default.
Important notices for setting RAID:
Before you install and configure RAID, check the current RAID setting on the computer you are servicing.
This product supports either RAID 0 or RAID 1. Confirm the RAID setting information provided by the
customer at first, then proceed with the installation.
To support RAID 0 or RAID 1, the computers you are servicing must be equipped with two rives.
Supported RAID levels
The following RAID levels are supported on RAID-supported models:
RAID 0 - Striped disk array
Better performance and no fault tolerance.
RAID 1 - Mirrored disk array
Improved read performance and 100% redundancy.
Configuring the system UEFI BIOS to enable embedded SATA RAID
functionality
Note: For RAID-supported models, the embedded SATA RAID functionality is enabled by default.
To configure the UEFI BIOS for RAID, do the following:
1. Press F1 to enter the ThinkPad Setup program.
2. Select Config.
3. Select Serial ATA (SATA).
4. Select SATA Controller Mode Option, and then the following options will be displayed:
• Compatibility
• AHCI
• RAID
5. Select RAID.
6. Press F10 to save changes and exit.
Attention: After you have enabled the SATA RAID functionality, reinstall the operating system before taking
any further RAID-related action.
© Copyright Lenovo 2012, 2013
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating RAID volumes
This topic describes how to use the Intel® Rapid Storage Technology option ROM configuration utility to
create RAID volumes.
To create RAID volumes, do the following:
1. Turn on the computer.
2. When a message Press <Ctrl-I> to enter Configuration Utility is displayed, press Ctr+I.
3. On the Intel Rapid Storage Technology option ROM screen, select Create RAID Volume, and then
press Enter.
4. Follow the instructions on the screen to select the RAID level and fill in other fields.
5. Select Create Volume. When a dialog box is displayed, press Y.
Attention: All the existing data stored on the selected drive will be erased while the RAID volume
is being created.
6. Exit the configuration utility.
Deleting RAID volumes
This topic describes how to use the Intel Rapid Storage Technology option ROM configuration utility to
delete RAID volumes.
To delete a RAID volume, do the following:
1. Turn on the computer.
2. When a message Press <Ctrl-I> to enter Configuration Utility is displayed, press Ctr+I.
3. On the Intel Rapid Storage Technology option ROM screen, select the RAID volume to be deleted,
and then press Delete.
4. When a dialog box is displayed, press Y to confirm the deletion of the selected RAID volume.
5. Exit the configuration utility.
48 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7. Status indicators
Indicator
Meaning
Orange: The speaker is on mute. To mute or unmute the speakers, press the
1
Speaker mute
indicator
speaker mute button.
2
3
Microphone mute
indicator
Orange: The microphone is on mute. By default, when the microphone is on mute,
none of the recording devices is available.
Wireless LAN, WAN,
or Bluetooth status
indicator
Green: The wireless LAN feature (the IEEE 802.11 b/g standard, 802.11 a/b/g, or
802.11n), wireless WAN feature, or Bluetooth feature is on.
Blinking green: Data is being transmitted.
4
5
Device access
status indicator
Blinking green: Data is being read from or written to the hard disk drive, the solid
state drive, or the device in the Serial Ultrabay™ Enhanced bay.
Power-on indicator
Green: The computer is on and ready to use. This indicator stays lit whenever the
computer is on and is not in sleep mode.
Slow blinking green: The computer is in sleep mode.
Fast blinking green: The computer is entering sleep mode or hibernation mode, or
is resuming normal operation.
6
7
Serial Ultrabay
Enhanced device
status indicator
Green: A Serial Ultrabay Enhanced device is installed and in use.
Blinking green: A Serial Ultrabay Enhanced device is being detached.
Off: A Serial Ultrabay Enhanced device is ready to be attached or detached.
Fingerprint reader
status indicator
Green: The fingerprint reader is ready to take fingerprint.
Blinking green once: The fingerprint is being authenticated or has been
authenticated.
Blinking green: The fingerprint reader is ready take fingerprint in power-on
authentication state.
Blinking amber: The fingerprint could not be authenticated.
Steady amber for 15 seconds: The power-on authentication feature is going to be
disabled after three bad fingerprint swipes.
8
9
Color sensor status
indicator
Green: The display color calibration has completed. When the computer lid opens,
the indicator turns off.
Blinking green: Display colors are being calibrated.
Battery status
indicator
Green: The battery charge level is 80% or more.
Blinking green: The battery charge level is between 20% and 80%, and charging is
continuing. When the battery charge level reaches 80%, the battery status indicator
stops blinking, but the charging might continue until the battery is 100% charged.
Slow blinking orange: The battery charge level is between 5% and 20%.
Quick blinking orange (0.5 second off every 1.5 seconds): The battery charge
level is 5% or less.
Fast blinking orange (0.25 second off every 0.5 second): An error has occurred
with the battery.
Off: The battery is fully charged or detached, or the computer is powered off.
50 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7. Status indicators (continued)
Indicator
Meaning
Note: If the computer is operating on battery power, the battery status indicator does
not work while the computer is turned off or is in sleep mode or hibernation mode.
10
Sleep status
indicator
Green: The computer is in sleep mode.
Blinking green: The computer is entering sleep mode or hibernation mode, or
is resuming normal operation.
Chapter 6. Status indicators 51
Download from Www.Somanuals.com. All Manuals Search And Download.
52 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7. Fn key combinations
The following table describes the functions of Fn key combinations.
Table 8. Fn key combinations
Key combination
Fn+F3
Description
Locks the computer.
Fn+F4
Puts the computer into sleep mode. To resume normal operation, press the Fn key.
Notes:
• To use the Fn+F4 key combination, you must have the ThinkPad Power Management
driver installed on the computer.
• If you want to use the combination to put the computer into hibernation mode, change
the power plan settings.
Fn+F5
Enables or disables the built-in wireless networking features and the Bluetooth features. If you
press Fn+F5, a list of wireless features is displayed. You can quickly change the power state
of each feature in the list.
Notes: If you want to use Fn+F5 to enable or disable the wireless features, the following
device drivers must be installed on the computer beforehand:
• ThinkPad Power Management driver
• OnScreen Display Utility
• Wireless device drivers
Fn+F6
Fn+F7
• For Windows 7: Opens the Communications settings window, in which you can preview
your video image, take a snapshot of your current image, and change the camera and
audio settings.
• For Windows 8: Starts the Lenovo Settings program, which enables you to change the
camera and audio settings.
Switches between the computer display and an external monitor. The following options will
be displayed:
• Computer display only (LCD)
• Computer display and external monitor (same image)
• Computer display and external monitor (extended desktop)
• External monitor only
Note: You also can use the Windows+P combination to switch between the computer display
and an external monitor.
Fn+F8
The computer display becomes dimmer.
The computer display becomes brighter.
Previous track/scene
Fn+F9
Fn+F10
Fn+F11
Fn+F12
Fn+Spacebar
Play or pause
Next track/scene
Controls the keyboard backlight and the ThinkLight® light.
• Press once: Turn on the keyboard backlight to low brightness level.
• Press again: Adjust the keyboard backlight to high brightness level.
• Press the third time: Turn off the keyboard backlight and turn on the ThinkLight light.
• Press the fourth time: Turn off the ThinkLight light.
Note: If your computer does not have a backlit keyboard, the Fn+Spacebar combination
controls only the ThinkLight light.
Fn+B
Has the same function as the Break key on a conventional keyboard.
© Copyright Lenovo 2012, 2013
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Table 8. Fn key combinations (continued)
Key combination
Fn+P
Description
Has the same function as the Pause key on a conventional keyboard.
Has the same function as the SysRq key on a conventional keyboard.
Has the same function as the ScrLK key on a conventional keyboard.
Fn+S
Fn+K
54 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8. Locations
This chapter introduces the locations of the computer hardware components.
Locating computer controls, connectors, and indicators
This topic introduces the locations of the computer controls, connectors, and indicators.
Front view
12 ExpressCard slot
on page 49)
2 Built-in microphones
3 Integrated camera
13 Fingerprint reader (on some models)
14 Color sensor (on some models)
15 Touch pad buttons
4 ThinkLight light
5 Power button
16 Touch pad
17 TrackPoint buttons
6 Security keyhole
7 RJ-45 Ethernet connector
8 Built-in stereo speakers
9 Serial Ultrabay Enhanced deviceor blank bezel
10 Combo audio jack
18 TrackPoint pointing stick
19 UltraNav® pointing device
20 Black button
21 Volume control buttons
11 Media card rader slot
© Copyright Lenovo 2012, 2013
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear view
6 USB 3.0 connectors
on page 49)
2 Smart card slot (on some models)
3 Wireless radio switch
7 Video graphics array (VGA) connector
8 Mini DisplayPort connector
9 ac power connector
4 IEEE 1394 connector
5 USB 2.0 connector
10 Always On USB connector
Bottom view
1
8
7
2
3
6
5
4
1 Battery pack
5 Memory module slot (bottom)
6 LCD cover latch
2 Battery pack latch
3 Docking connector
7 Serial Ultrabay Enhanced lock latch
8 Serial Ultrabay Enhanced eject latch
4 Solid state drive or hard disk drive slot
Locating FRUs and CRUs
This topic introduces the following service parts:
•
56 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Notes:
• Each FRU is available for all types or models, unless otherwise specified.
• CRU statement for customers:
You can resolve some problems with your product with a replacement part you can install yourself,
called a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as self-service CRUs and
others are designated as optional-service CRUs. Installation of self-service CRUs is your responsibility.
For optional-service CRUs, you can either install the CRU yourself or you can request that a Service
Provider installs the CRU according to the warranty service for your product. If you intend on installing
the CRU, Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped
with your product and are available from Lenovo at any time upon request. You can find a list of CRUs
for your product in this Hardware Maintenance Manual. An electronic version of this manual can be
instructions to find the manual for your product. You might be required to return the defective part
that is replaced by the CRU. When return is required: (1) return instructions, a prepaid shipping label,
and a container will be included with the replacement CRU; and (2) you might be charged for the
replacement CRU if Lenovo does not receive the defective CRU within thirty (30) days of your receipt of
the replacement CRU. See your Lenovo Limited Warranty documentation for full details.
ThinkPad computers contain the following types of CRUs:
– Self-service CRUs: These CRUs unplug or are held by no more than two screws. Examples of
these types of CRUs include the ac power adapter, power cord, battery, and hard disk drive. Other
self-service CRUs depending on product design might include the memory module, wireless card,
keyboard, and palm rest with finger print reader and touchpad.
– Optional-service CRUs: These CRUs are isolated parts within the computer that are concealed by an
access panel that is typically secured by more than two screws. Once the access panel is removed,
the specific CRU is visible.
Chapter 8. Locations 57
Download from Www.Somanuals.com. All Manuals Search And Download.
Major FRUs and CRUs
25
24
1
2
3
23
4
5
22
21
6
7
20
19
8
18
17
16
9
10
15
11
14
13
12
9
Table 9. Major FRUs and CRUs
No.
FRU description
Self-service CRU
Optional-service
CRU
1
2
No
No
No
No
Palm rest assembly
58 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 9. Major FRUs and CRUs (continued)
No.
FRU description
Self-service CRU
Optional-service
CRU
3
Yes
No
No
No
No
Yes
Yes
No
Yes
No
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
Yes
Yes
No
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
ExpressCard blank bezel or ExpressCard
Speaker assembly
4
5
mSATA solid state drive
6
PCI Express Mini Card for wireless WAN
Backup battery
7
8
Serial Ultrabay Enhanced device or blank bezel
Memory module or dummy memory module
I/O sub card
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Battery
Base cover assembly
Memory module slot cover
Hard disk drive slot cover
Hard disk drive rubber rails or solid state drive spacers
Hard disk drive or solid state drive
System board
Microprocessor
Bluetooth daughter card
PCI Express Mini Card for wireless LAN
Magnesium structure frame
Thermal fan assembly
Smart card or dummy smart card
Keyboard
TrackPoint cap
Chapter 8. Locations 59
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD FRUs and CRUs
1
10
2
3
9
8
7
4
5
6
Table 10. LCD FRUs and CRUs
No.
FRU description
Self-service
CRU
Optional-service
CRU
1
2
3
4
5
No
No
No
No
No
No
No
No
No
No
liquid crystal display (LCD) bezel assembly
Integrated camera
Hinge kit
LED cable
Antenna kit
60 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 10. LCD FRUs and CRUs (continued)
No.
FRU description
Self-service
CRU
Optional-service
CRU
6
No
No
No
No
No
No
No
No
No
No
LCD rear cover assembly
LCD cable
7
8
LED sub card
LCD panel
9
10
Clear plate
Important:
For color sensor models, if the LCD panel needs a replacement, order a special LCD panel FRU kit
from Lenovo. The FRU kit contains a LCD panel, a CD and an instruction flyer. For the correct FRU kit
Miscellaneous kits and other FRUs
Table 11. Miscellaneous kits
FRU descriptions
Self-service
CRU
Optional
service CRU
No
No
System board miscellaneous kit:
• Thermal Pad
• CPU bracket
• Insulation Sheet
• Spec
Base cover miscellaneous kit:
• Base Cover sub assembly parts which can be removable
• Spec
No
No
No
No
System miscellaneous kit:
• Cable DC-in
• Cable Smart Card
• Spacer Smart Card
• Spacer Smart Card Reader
• Dymmy Express Card
• Dymmy Color Sensor
• Spec
No
No
No
No
Screw kit:
• Spec
Tape kit:
• Spec
Table 12. Other FRUs
FRU descriptions
Self-service
CRU
Optional
service CRU
ac adapter
Power cord
Yes
Yes
No
No
Looking up FRU information
For detailed FRU information, including part numbers, descriptions, and substitution part numbers, go to
Chapter 8. Locations 61
Download from Www.Somanuals.com. All Manuals Search And Download.
62 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9. FRU replacement notices
This chapter presents notices related to removing and replacing parts. Read this chapter carefully before
replacing any FRU.
CRU statement for customers:
You can resolve some problems with your product with a replacement part you can install yourself, called
a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as self-service CRUs and others
are designated as optional-service CRUs. Installation of self-service CRUs is your responsibility. For
optional-service CRUs, you can either install the CRU yourself or you can request that a Service Provider
installs the CRU according to the warranty service for your product. If you intend on installing the CRU,
Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your
product and are available from Lenovo at any time upon request. You can find a list of CRUs for your
product in this Hardware Maintenance Manual. An electronic version of this manual can be found at
http://www.lenovo.com/support. Click User Guides & Manuals and then follow the on-screen instructions
to find the manual for your product. You might be required to return the defective part that is replaced by
the CRU. When return is required: (1) return instructions, a prepaid shipping label, and a container will be
included with the replacement CRU; and (2) you might be charged for the replacement CRU if Lenovo does
not receive the defective CRU within thirty (30) days of your receipt of the replacement CRU. See your
Lenovo Limited Warranty documentation for full details.
Screw notices
Loose screws can cause a reliability problem. In the ThinkPad notebook computer, this problem is addressed
with special nylon-coated screws that have the following characteristics:
• They maintain tight connections.
• They do not easily come loose, even with shock or vibration.
• They are harder to tighten.
Do the following when you service this machine:
• Keep the screw kit in your tool bag. For the part number of the screw kit, go to
• It is recommended to use new screws.
• It is recommended to use each screw only once.
• Use a torque screwdriver if you have one.
Tighten screws as follows:
• Plastic to plastic
Turn an additional 90 degrees after the screw head touches the surface of the plastic part:
• Logic card to plastic
Turn an additional 180 degrees after the screw head touches the surface of the logic card:
© Copyright Lenovo 2012, 2013
63
Download from Www.Somanuals.com. All Manuals Search And Download.
• Torque driver
If you have a torque driver, refer to the Torque column in the screw information table for each step.
– Make sure that you use the correct screw. It is recommended to use new screws for replacements. If
you have a torque screwdriver, tighten all screws firmly to the torque specified in the screw information
table for each step.
– Ensure torque screw drivers are calibrated correctly following country specifications.
Retaining serial numbers
This section includes the following descriptions:
•
•
•
Restoring the serial number of the system unit
When the computer was manufactured, the EEPROM on the system board was loaded with the serial
numbers of the system and all major components. These numbers need to remain the same throughout
the life of the computer.
If you replace the system board, you must restore the serial number of the system unit to its original value.
Before replacing the system board, save the original serial number by doing the following:
1. Install the latest version of LENOVO ThinkPad Hardware Maintenance Diskette or Maintenance Key,
and then restart the computer.
2. From the main menu, select 1. Set system identification.
3. Turn off the computer, and then turn on the computer again.
4. When the ThinkPad logo is displayed, press Esc.
5. Select 2. Read S/N data from EEPROM and follow the instructions on the screen. The serial number of
each device in your computer is displayed; the serial number of the system unit is listed as follows:
• 20 Serial number
6. Write down that number.
Note: The serial number of the system unit is also written on the label attached to the bottom of the
computer.
After you have replaced the system board, restore the serial number by doing the following:
1. Install the latest version of LENOVO ThinkPad Hardware Maintenance Diskette or Maintenance Key,
and then restart the computer.
2. From the main menu, select 1. Set system identification.
3. Turn off the computer, and then turn on the computer again.
4. When the ThinkPad logo is displayed, press Esc.
5. Select 1. Add S/N data from EEPROM. Follow the instructions on the screen.
64 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
If the MTM and Product ID numbers differ from each other on the rear label, use what is shown for the
Product ID field. See the following example:
MTM on the rear label:
TTTT-CTO S/N SSSSSSS
Product ID on the rear label:
TTTT-MMM (Use this number when setting Serial Number.)
In the example, the Serial Number to be input is “1STTTTMMMSSSSSSS”.
Retaining the UUID
The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to your computer at
production and stored in the EEPROM of your system board.
The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400. No two
computers in the world have the same number.
When you replace the system board, follow the following steps to create new UUID for the system board if
the system board does not have a UUID:
1. Install the latest version of LENOVO ThinkPad Hardware Maintenance Diskette or Maintenance Key,
and then restart the computer.
2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already
exists, it is not overwritten.
Reading or writing the ECA information
Information on Engineering Change Announcements (ECA) are stored in the EEPROM of the system board.
The electronic storage of this information simplifies the procedure to check if the ECA has been previously
applied to a machine. The machine does not need to be disassembled to check for the ECA application.
To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write
function on the LENOVO ThinkPad Hardware Maintenance Diskette or Maintenance Key.
1. Insert the latest version of LENOVO ThinkPad Hardware Maintenance Diskette or Maintenance Key,
and then restart the computer.
2. From the main menu, select 6. Set ECA Information.
3. To read the ECA information, select 2. Read ECA/rework number from EEPROM and follow the
instructions on the screen; To read box build date, select 5. Read box build date from EEPROM, and
follow the instructions on the screen.
After an ECA has been applied to the machine, the EEPROM must be updated to reflect the ECA's
application. Use the latest version of LENOVO ThinkPad Hardware Maintenance Diskette or Maintenance
Key to update the EEPROM.
Note: Only the ECA number is stored in the EEPROM. The machine type of the ECA is assumed to be the
same as the machine type of the machine that had the ECA applied to it.
1. Insert the latest version of LENOVO ThinkPad Hardware Maintenance Diskette or Maintenance Key,
and then restart the computer.
2. From the main menu, select 6. Set ECA Information.
3. To write the ECA information, select 1. Write ECA/rework number from EEPROM, and follow the
instruction; To write box build date, select 4. Write box build date from EEPROM, and follow the
instruction on the screen.
Chapter 9. FRU replacement notices 65
Download from Www.Somanuals.com. All Manuals Search And Download.
If the system board is being replaced, try to read the ECA information from the old system board and transfer
the information to the new system. If the system board is inoperable, this will not be possible.
66 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 10. Removing or replacing a FRU
This chapter provides instructions on how to remove or replace a FRU.
CRU statement for customers:
You can resolve some problems with your product with a replacement part you can install yourself, called
a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as self-service CRUs and others
are designated as optional-service CRUs. Installation of self-service CRUs is your responsibility. For
optional-service CRUs, you can either install the CRU yourself or you can request that a Service Provider
installs the CRU according to the warranty service for your product. If you intend on installing the CRU,
Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your
product and are available from Lenovo at any time upon request. You can find a list of CRUs for your
product in this Hardware Maintenance Manual. An electronic version of this manual can be found at
http://www.lenovo.com/support. Click User Guides & Manuals and then follow the on-screen instructions
to find the manual for your product. You might be required to return the defective part that is replaced by
the CRU. When return is required: (1) return instructions, a prepaid shipping label, and a container will be
included with the replacement CRU; and (2) you might be charged for the replacement CRU if Lenovo does
not receive the defective CRU within thirty (30) days of your receipt of the replacement CRU. See your
Lenovo Limited Warranty documentation for full details.
General guidelines
When removing or replacing a FRU, be sure to observe the following general guidelines:
1. Do not try to service any computer unless you have been trained and certified. An untrained person runs
the risk of damaging parts.
3. Begin by removing any FRUs that have to be removed before replacing the failing FRU. Any such
FRUs are listed at the beginning of each FRU replacement procedure. Remove them in the order in
which they are listed.
4. Follow the correct sequence in the steps for removing the FRU, as given in the drawings by the
numbers in square callouts.
5. When turning a screw, turn it in the direction as given by the arrow in the drawing.
6. When removing the FRU, move it in the direction as given by the arrow in the drawing.
7. To put the new FRU in place, reverse the removal procedure and follow any notes that pertain to
replacement. For information about connecting and arranging internal cables, see Chapter 8 “Locations”
on page 55.
8. When replacing a FRU, use the correct screw as shown in the replacement procedure.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets,
remove the battery pack, and then disconnect any interconnecting cables.
Attention:
• After replacing a FRU, do not turn on the computer until you have made sure that all screws, springs, and
other small parts are in place and none are loose inside the computer. Verify this by shaking the computer
gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.
© Copyright Lenovo 2012, 2013
67
Download from Www.Somanuals.com. All Manuals Search And Download.
• The system board is sensitive to, and can be damaged by, electrostatic discharge. Before touching it,
establish personal grounding by touching a ground point with one hand or by using an electrostatic
discharge (ESD) strap.
Before servicing ThinkPad T530, T530i, and W530
Removal steps of SIM card
Some models you are servicing might have the SIM card that the customer has installed. If the computer you
are servicing has the SIM card installed, remove it before you start the servicing.
To remove the SIM card, you need to remove the battery pack first. See “1010 Battery pack” on page 68.
After you finish the servicing, make sure that you insert the card back into the slot firmly.
1010 Battery pack
Important notice for replacing a battery pack:
• The Lenovo Solution Center programprovides an automatic battery diagnostic test that determines if the
battery pack is defective. A battery pack FRU should not be replaced unless this diagnostic test shows
that the battery is defective. The only exception to this is if the battery pack is physically damaged or
a customer is reporting a possible safety issue.
• If the Lenovo Solution Center program is not installed in the computer, the customer should download this
program before a non-physically damaged battery pack is replaced. Note that a physically damaged
battery pack is not covered by the warranty.
Removal steps of battery pack
DANGER
Use only the authorized battery specified for your computer. Any other battery could ignite or
explode.
Unlock the battery latch and hold the battery latch in the unlocked position. Then, remove the battery pack.
68 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2
When installing: Install the battery pack in the slot, and then make sure that the battery latch is in the
locked position.
1020 Serial Ultrabay Enhanced device or blank bezel
For access, remove this FRU:
•
Removal steps of Serial Ultrabay Enhanced device or blank bezel
Hold the bay lock latch in the unlocked position 1 and slide the bay eject latch 2 . Then, pull out the Serial
Ultrabay Enhanced device or the blank bezel in the direction shown by the arrow 3 .
1
2
3
Note: For RAID models, to remove the second hard disk drive, you need to remove the screw that secures
the second hard disk drive adapter first.
Chapter 10. Removing or replacing a FRU 69
Download from Www.Somanuals.com. All Manuals Search And Download.
Torque
Step
Screw (quantity)
Color
NA
Black
0.392 Nm
(4 kgf-cm)
M3 × 5 mm, flat-head (1)
1030 Memory module slot cover
For access, remove this FRU:
•
Removal steps of memory module slot cover
Note: Loosen the screws 1 , but do not remove them.
70 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
1040 Memory module (bottom slot)
For access, remove these FRUs in order:
•
•
Removal steps of memory module (bottom slot)
Attention: For ThinkPad W530 models that come with two dummy cards installed, do not replace the
dummy cards with memory modules. Otherwise, the system might not function correctly.
Chapter 10. Removing or replacing a FRU 71
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
1
When installing: Insert the notched end of the memory module into the slot. Press the memory module
firmly, and pivot it until it snaps into place. Make sure that it is firmly installed in the slot and does not
move easily.
1050 Hard disk drive or solid state drive
For access, remove this FRU:
•
Attention:
• Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper
handling can cause damage and permanent loss of data.
• Before removing the drive, have the user make a backup copy of all the information on it if possible.
• Never remove the drive while the system is operating or is in suspend mode.
Removal steps of hard disk drive or solid state drive
Note: Loosen the screw 1 , but do not remove it.
72 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
For hard disk drive and rubber rails:
4
4
For solid state drive and spacers:
4
4
Chapter 10. Removing or replacing a FRU 73
Download from Www.Somanuals.com. All Manuals Search And Download.
When installing: Make sure that the solid state drive connector or hard disk drive connector is attached
firmly.
1060 Keyboard
For access, remove these FRUs in order:
•
•
Removal steps of keyboard
1. Remove the screws that secure the keyboard.
1
1
Torque
Step
Screw (quantity)
M2 × 14 mm, wafer-head, nylon-coated (2)
Color
1
Black
0.181 Nm
(1.85 kgf-cm)
2. Press the keyboard in the direction shown by the arrow 2 until the front edge of the keyboard is
detached from the keyboard bezel.
74 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Lift the keyboard in the direction shown by the arrow 3 , and then detach the connector 4 .
Installation steps of keyboard
When installing the keyboard, do the following:
1. Attach the keyboard connector 1 .
Chapter 10. Removing or replacing a FRU 75
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2. Attach the keyboard and ensure that the keyboard edges a are under the frame.
3. When the front side of the keyboard is housed firmly, gently press the keys with your thumbs and slide
the keyboard toward you until the keyboard is in place.
76 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Make sure that the front side of the keyboard b is housed firmly.
4. Secure the keyboard by tightening the screws from the bottom side of the computer.
1070 Memory module (upper slot)
For access, remove these FRUs in order:
•
•
•
Removal steps of memory module (upper slot)
Attention: For ThinkPad W530 models that come with two dummy cards installed, do not replace the
dummy cards with memory module. Otherwise, the system might not function correctly.
Chapter 10. Removing or replacing a FRU 77
Download from Www.Somanuals.com. All Manuals Search And Download.
When installing: Insert the notched end of the memory module into the socket. Press the memory module
firmly, and pivot it until it snaps into place. Make sure that it is firmly installed in the slot and does not
move easily.
1080 PCI Express Mini Card for wireless LAN
For access, remove these FRUs in order:
•
•
•
Removal steps of PCI Express Mini Card for wireless LAN
In step 1 , unplug the connectors by using the antenna RF connector removal tool or pick the connectors
with your fingers and gently unplug them in direction of the arrow.
Note: Some models might have only two antenna cables in step 1 .
78 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Torque
Step
Screw (quantity)
Color
2
0.181 Nm
M2 × 3 mm, wafer-head, nylon-coated (1)
Silver
(1.85 kgf-cm)
Chapter 10. Removing or replacing a FRU 79
Download from Www.Somanuals.com. All Manuals Search And Download.
When installing:
• In models with a wireless LAN card that has two antenna connectors, plug the gray cable into the main
connector, and the black cable into the auxiliary connector on the card. If the computer you are servicing
has three cables, put the white cable in the cable protection tube as shown in the following illustration.
• In models with a wireless LAN card that has three antenna connectors, plug the gray cable (MAIN) into
the main connector, the black cable (AUX) into the auxiliary connector, and the white cable (3rd) into
the last connector,
1090 PCI Express Mini Card for wireless WAN or mSATA solid state drive
For access, remove these FRUs in order:
•
•
•
Removal steps of PCI Express Mini Card for wireless WAN (full-size WWAN card)
In step 1 , unplug the connectors by using the antenna RF connector removal tool or pick the connectors
with your fingers and gently unplug them in direction of the arrow.
80 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Torque
Step
Screw (quantity)
Color
2
0.181 Nm
M2 × 3 mm, wafer-head, nylon-coated (1)
Silver
(1.85 kgf-cm)
Chapter 10. Removing or replacing a FRU 81
Download from Www.Somanuals.com. All Manuals Search And Download.
4
When installing: Plug the red cable into the main connector and the blue cable into the auxiliary connector.
Removal steps of PCI Express Mini Card for wireless WAN (half-size WWAN card)
In step 1 , unplug the connectors by using the antenna RF connector removal tool or pick the connectors
with your fingers and gently unplug them in direction of the arrow.
82 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Torque
Step
Screw (quantity)
Color
2
0.181 Nm
M2 × 3 mm, wafer-head, nylon-coated (1)
Silver
(1.85 kgf-cm)
4
5
5
Removal steps of mSATA solid state drive
The computer comes with either a PCI Express Mini Card for wireless WAN or an mSATA solid-state drive. If
the computer is equipped with an mSATA solid-state drive, it is installed in the wireless WAN card slot.
Attention:
• Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper
handling can cause damage and permanent loss of data.
• Before removing the drive, have the user make a backup copy of all the information on it if possible.
• Never remove the drive while the system is operating or is in suspend mode.
Chapter 10. Removing or replacing a FRU 83
Download from Www.Somanuals.com. All Manuals Search And Download.
• Ensure that you partition the mSATA solid-state drive after installing it on the computer you are servicing.
Otherwise, the mSATA solid-state drive will not function correctly. For instructions on on how to partition
2
Torque
Step
Screw (quantity)
Color
2
0.181 Nm
M2 × 3 mm, wafer-head, nylon-coated (1)
Silver
(1.85 kgf-cm)
3
1100 ExpressCard blank bezel or ExpressCard
Removal steps of ExpressCard blank bezel or ExpressCard
When you press the ExpressCard blank bezel or ExpressCard 1 , it pops out 2 .
84 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
When installing: Make sure that the ExpressCard blank bezel or ExpressCard is correctly oriented as
shown in the following illustration.
1110 Keyboard bezel assembly
For access, remove these FRUs in order:
•
•
•
•
Chapter 10. Removing or replacing a FRU 85
Download from Www.Somanuals.com. All Manuals Search And Download.
Important:
Read the following instructions first before replacing the keyboard bezel assembly for ThinkPad W530 models
with a color sensor.
• If the hard disk drive is not defective, and only the keyboard bezel assembly needs a replacement:
1. Replace the keyboard bezel assembly.
2. After you replace the keyboard bezel assembly, start the computer and run the Sensor Replacement Utility
program by clicking Start ➙ All Programs ➙ X-Rite ➙ PANTONE Color Calibrator ➙ Sensor Replacement
Utility.
3. If you do not have access to the hard disk drive, provide the customer with information on how to run the
Sensor Replacement Utility.
• If both the hard disk drive and the keyboard bezel assembly need replacements:
1. Before you replace the keyboard bezel assembly, back up the color sensor calibration profile
ECCM2SensorData.dat to an external media device from the directory C:\ProgramData\X-Rite\ECCM-2. This
calibration profile is generated after you use the color sensor for the first time.
2. If you are unable to back up the color sensor calibration profile, and if no problem was reported with the color
sensor, follow the steps at the end of this topic to remove the color sensor from the original keyboard bezel
assembly, and install the color sensor to the new keyboard bezel assembly.
3. Replace the hard disk drive. See “1050 Hard disk drive or solid state drive” on page 72. Then reload the
operating system.
4. If the Sensor Replacement Utility program cannot be launched successfully, restore the color
sensor calibration profile ECCM2SensorData.dat, which you have backed up in step 1, to the directory
C:\ProgramData\X-Rite\ECCM-2.
5. If you did not back up the calibration profile and the customer does not have a backup of their image,
you will also need to replace the LCD panel even if the LCD panel is not broken. See “2040 LCD cable,
6. Run the Sensor Replacement Utility program again and follow the instructions on the screen to perform the
initial color calibration, or provide instructions to the customer to run this utility.
7. When the initial calibration completes, a dialog box is displayed. Click OK to exit the Sensor Replacement
Utility program.
Removal steps of keyboard bezel assembly
1
1
1
1
2
1
1
1
2
Torque
Step
Screw (quantity)
Color
1
Black
0.181 Nm
M2 × 14 mm, bind-head, nylon-coated (7)
(1.85 kgf-cm)
2
Black
0.181 Nm
M2 × 4 mm, bind-head, nylon-coated (2)
(1.85 kgf-cm)
86 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
5
6
5
6
7
Chapter 10. Removing or replacing a FRU 87
Download from Www.Somanuals.com. All Manuals Search And Download.
For ThinkPad W530 models with a color sensor, if you need to remove the color sensor from the
failing keyboard bezel assembly and install the color sensor to the new keyboard bezel assembly,
do the following:
3
3
4
1
2
Torque
Step
Screw (quantity)
Color
3
0.181 Nm
M2 × L7 mm, bind-head, (2)
Silver
(1.85 kgf-cm)
1
4
4
3
2
1120 Bluetooth daughter card
For access, remove these FRUs in order:
•
•
•
88 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Removal steps of Bluetooth daughter card
Torque
Step
Screw (quantity)
Color
1
0.181 Nm
M2 × 3 mm, wafer-head, nylon-coated (1)
Silver
(1.85 kgf-cm)
When installing: Make sure that the connector is attached firmly.
1130 Backup battery
For access, remove these FRUs in order:
•
•
•
•
Removal steps of backup battery
DANGER
Use only the authorized battery specified for your computer. Any other battery could ignite or
explode.
Chapter 10. Removing or replacing a FRU 89
Download from Www.Somanuals.com. All Manuals Search And Download.
When installing: Make sure that the battery connector is attached firmly.
1140 Smart card, dummy smart card and spacer
For access, remove these FRUs in order:
•
•
•
•
Removal steps of smart card
3
3
3
4
1
2
90 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Torque
Step
Screw (quantity)
Color
3
0.181 Nm
M2 × 3 mm, wafer-head, nylon-coated (3)
Silver
(1.85 kgf-cm)
5
6
5
Removal steps of dummy smart card and spacer
3
1
1
1
2
Torque
Step
Screw (quantity)
Color
1
0.181 Nm
M2 × 3 mm, wafer-head, nylon-coated (3)
Silver
(1.85 kgf-cm)
1150 Speaker assembly
For access, remove these FRUs in order:
•
•
•
•
Chapter 10. Removing or replacing a FRU 91
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal steps of speaker assembly
Torque
Step
Screw (quantity)
Color
1
0.181 Nm
M2 × 3 mm, wafer-head, nylon-coated (4)
Silver
(1.85 kgf-cm)
5
5
5
4
4
5
5
4
4
When installing: Make sure that the speaker connector is attached firmly. Then route the cables and secure
them properly as shown in the illustration above.
1160 Thermal fan assembly
For access, remove these FRUs in order:
•
•
92 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
Removal steps of thermal fan assembly
1
When installing: Make sure that the connector is attached firmly.
Notes:
• Loosen the screws 3a to 3d in ascending alphabetic order as illustrated, but do not remove them.
• Some models do not have screws 4 . For those models, skip step 4 .
2
4
3a
4
3d
4
3c
3b
Chapter 10. Removing or replacing a FRU 93
Download from Www.Somanuals.com. All Manuals Search And Download.
5
When installing: Before you attach the thermal fan assembly to the computer, apply thermal grease, at an
amount of 0.2 grams, on the parts marked a as in the following illustrations. Either too much or too less
application of grease can cause a thermal fan problem due to imperfect contact with a component. For the
new thermal fan assembly, you need to peel the thin film off from the rubbers.
For Integrated Graphics models:
For Switchable Graphics models:
94 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
a
a
For Workstation models:
a
a
1170 Microprocessor
For access, remove these FRUs in order:
•
•
•
•
•
•
Attention: The microprocessor is extremely sensitive. When you service the microprocessor, avoid any
kind of rough handling.
Removal steps of microprocessor
Rotate the head of the screw in the direction shown by the arrow 1 to release the lock; then remove the
microprocessor 2 .
Chapter 10. Removing or replacing a FRU 95
Download from Www.Somanuals.com. All Manuals Search And Download.
2
1
a
When installing: Place the microprocessor in the microprocessor socket, and then rotate the head of the
screw in the direction shown by the arrow a to secure the microprocessor.
1180 LCD unit
For access, remove these FRUs in order:
•
•
•
•
•
•
•
96 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal steps of LCD unit
2
1
2
1
Torque
Step
Screw cap
Screw (quantity)
Color
1
Black
0.392 Nm
M2.5 × 6 mm, wafer-head, nylon-coated (2)
(4.0 kgf-cm)
2
—
Black
0.392 Nm
M2.5 × 6 mm, wafer-head, nylon-coated (2)
(4.0 kgf-cm)
3
3
Torque
Step
Screw (quantity)
Color
3
Black
0.392 Nm
M2.5 × 6 mm, wafer-head, nylon-coated (2)
(4.0 kgf-cm)
Chapter 10. Removing or replacing a FRU 97
Download from Www.Somanuals.com. All Manuals Search And Download.
4
4
7
6
5
9
9
9
8
9
8
8
9
9
8
Torque
Step
Screw (quantity)
M2 × 4 mm, wafer-head, nylon-coated (2)
Color
Black
4
0.181 Nm
(1.85 kgf-cm)
When installing:
• Make sure that you attach the LCD connector firmly.
• Make sure that you route the cables firmly and tape up in the proper positions as shown in the following
illustration.
• When you route the cables, make sure that they are not subject to any tension. Tension could cause the
cables to be damaged by the cable guides, or a wire to be broken.
98 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal steps of base cover assembly
1
2
1
Torque
Step
Screw (quantity)
Color
1
0.181 Nm
M2 × 3 mm, wafer-head, nylon-coated (2)
Silver
(1.85 kgf-cm)
2
Black
0.181 Nm
M2 × 14 mm, wafer-head, nylon-coated (1)
(1.85 kgf-cm)
4
3
Applying labels to the base cover
The new base cover FRU is shipped with a kit containing labels of several kinds, including but not limited to
those described in this topic.
The following illustration shows the correct location of each label.
100 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
21
20
9
9
10
19
18
17
15
16
14 13
12 11
When you replace the base cover, apply the following labels:
7 Machine type and serial number label
6 FCC label
Note: If the base cover has two FCC labels, apply both to the new base cover.
Other labels need to be peeled off from the old base cover, and need to be adhered to the new one. The
labels include but are not limited to the following:
1 Taiwan GEO label
13 China 3G wireless WAN label
14 China wireless WAN label
15 ISRAEL label
2 Taiwan wireless WAN label
3 Certificate of Authentication (COA) label
4 System label with compliance ID
5 Wireless WAN label
16 Brazil wireless WAN label
17 Brazil Bluetooth label
8 Information label
18 Brazil wireless card label
19 SIRIM label or Indonesia POSTEL label
20 China GEO label
9 Asset tag
10 Indonesia rating label or non-encryption label
11 China TELCOM label
21 IBM server GEO label
12 China 3G logo wireless WAN label
Note: If the COA label is attached to a part that is replaced, return the old part with the label attached to the
customer, or provide a letter to the customer stating what the label was originally on the computer and what
the label part number, serial number, and product key were.
1200 I/O sub card
Note: The I/O sub card contains an Ethernet connector and a USB connector.
Chapter 10. Removing or replacing a FRU 101
Download from Www.Somanuals.com. All Manuals Search And Download.
For access, remove these FRUs in order:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Removal steps of I/O sub card
1
1
2
Torque
Step
Screw (quantity)
M2 × 7 mm, wafer-head, nylon-coated (2)
Color
1
0.181 Nm
Silver
(1.85 kgf-cm)
When installing: Make sure that the connector is attached firmly.
1210 System board assembly and magnesium structure frame
Note: The system board does not contain the Ethernet connector and the ac power connector. For the
magnesium structure frame.
For access, remove these FRUs in order:
•
•
•
•
•
•
102 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
•
•
•
•
•
•
•
•
•
•
Important notices for RAID setting:
Before you replace the system board, ensure that you have read Chapter 5 “Installing and configuring RAID”
on page 47, and have obtained the necessary information. After you replace the system board, RAID mode
is recovered to default. To verify the RAID mode setting, check the ThinkPad Setup setting by selecting
Config ➙ Serial ATA (SATA) ➙ SATA Controller Mode Option ➙ RAID/Compatibility/AHCI. Then, you
will see that the RAID option is enabled.
Important notices for handling the system board:
When handling the system board, bear the following in mind:
• The system board has an accelerometer, which can be broken if several thousands of G-forces are applied.
Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject
the accelerometer to as much as 6,000 G's of shock.
• Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite.
• If a system board is dropped, be sure to document the drop in any reject report, and replace the system board.
• Avoid rough handling of any kind.
• At every point in the process, be sure not to drop or stack the system board.
• If you put a system board down, be sure to put it only on a padded surface such as an ESD mat or conductive
corrugated material.
Location of major sensitive components on the system board
Attention: The following components soldered on the top side of the system board are extremely sensitive.
When you service the system board, avoid any kind of rough handling.
a
Microprocessor
b
Platform Controller Hub (PCH)
c
Accelerometer chip for the hard disk drive Active Protection System™
d
Graphics chip
Note: The graphics chip d is only for the switchable graphics models and workstation models.
The system board in integrated graphics models does not have this chip.
For Integrated Graphics models:
Chapter 10. Removing or replacing a FRU 103
Download from Www.Somanuals.com. All Manuals Search And Download.
c
For Switchable Graphics models:
d
c
For Workstation models:
d
b
c
104 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal steps of system board and magnesium structure frame
1
4
4
5
3
2
2
Torque
Step
Screw (quantity)
Color
2
0.392 Nm
Hex stud, nylon-coated (2)
Silver
(4.0 kgf-cm)
3
4
0.181 Nm
(1.85 kgf-cm)
M2 × 3 mm, wafer-head, nylon-coated (1)
M2 × 7 mm, wafer-head, nylon-coated (2)
Silver
Silver
0.181 Nm
(1.85 kgf-cm)
When installing: When you replace the system board, attach thermal rubbers as shown in the following
illustration. Depending on the models you are servicing, the number of thermal rubbers are different. Check
the thermal rubbers on the old system board, and find duplicates of them in the new FRU package and
apply them to the new system board.
Chapter 10. Removing or replacing a FRU 105
Download from Www.Somanuals.com. All Manuals Search And Download.
b
a
c
d
2010 LCD bezel assembly
For access, remove this FRU:
•
Removal steps of LCD bezel assembly
1
1
1
Torque
Step
Screw cap
Screw (quantity)
M2.5 × 6 mm, wafer-head, nylon-coated (3)
Color
1
Black
0.392 Nm
(4.0 kgf-cm)
106 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2
2
2
2
2
2
2
2
3
When installing: Make sure that all the latches are attached firmly.
2020 LED sub card
For access, remove these FRUs in order:
•
•
Removal steps of LED sub card
Note: Some models do not have the connector 1a .
1a
When installing: Make sure that the connectors are attached firmly and the card is installed as shown in
the following illustration.
Chapter 10. Removing or replacing a FRU 107
Download from Www.Somanuals.com. All Manuals Search And Download.
2030 Integrated camera
For access, remove these FRUs in order:
•
•
Removal steps of integrated camera
1
3
2
Torque
Step
Screw (quantity)
Color
1
0.181 Nm
M2 × 3 mm, wafer-head, nylon-coated (1)
Silver
(1.85 kgf-cm)
When installling: Make sure that the connector of the integrated camera is attached firmly.
2040 LCD cable, camera cable, LCD panel, and hinges
For access, remove these FRUs in order:
•
•
•
•
•
•
•
•
•
108 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Read this first before replacing the LCD panel
For ThinkPad W530 models with a color sensor:
Important:
If your LCD panel needs a replacement, order a special LCD panel FRU kit for color sensor model from Lenovo.
The FRU kit contains a LCD panel, a CD and an instruction flyer. For the correct FRU kit part number, check on
To replace the LCD panel, be sure to follow these steps:
1. Before you replace the LCD panel, locate the label on the plastic jacket of the new LCD panel. Locate
the numeric key number on the label and record it.
2. Replace the failing LCD panel with the new one that was shipped to you. For the detailed replacement
3. Start the computer and enter the Windows operating environment.
4. Insert the CD that came with the new LCD panel. If the autorun function is enabled, the
Panel Replacement Utility program starts automatically. If the program does not start automatically, run
the program manually by exploring the CD and double-clicking PanelReplacementUtility.exe.
5. Follow the instructions on the screen to perform the initial color calibration. When the key number is
required, type the number that you recorded in step 1. Then the Panel Replacement Utility program
starts to measure the new LCD panel and perform the initial color calibration.
6. When the initial calibration is finished, a dialog box is displayed. Click OK to exit the
Panel Replacement Utility program.
Important: If the computer is protected by a hard disk drive password or a Windows password, do one
of the following:
• Ask the customer for the password to run the Panel Replacement Utility program.
• Provide the CD and the numeric key number to the customer and guide the customer to run the Panel
Replacement Utility program.
Failing to run the Panel Replacement Utility program will require another LCD panel replacement.
Removal steps of LCD cable, camera cable, LCD panel, and hinges
In step 1 , release the antenna cables from the left and right hinges.
Chapter 10. Removing or replacing a FRU 109
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1
2
2
2
2
When installing: When attaching the LCD panel to the cover, press the left and right edges covered with
metal gently with your fingers. Do not press the surface of the panel or apply any excessive force to the panel.
110 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
5
5
5
6
7
8
When installing: Make sure that the LCD cable connector is attached firmly.
Chapter 10. Removing or replacing a FRU 111
Download from Www.Somanuals.com. All Manuals Search And Download.
9
10
9
9
10
9
Torque
Step
Screw (quantity)
Color
9
0.181 Nm
M2 × 3 mm, wafer-head, nylon-coated (4)
Silver
(1.85 kgf-cm)
2050 Antenna kit and LCD rear cover assembly
For access, remove these FRUs in order:
•
•
•
•
•
•
•
•
•
•
Removal steps of antenna kit and LCD rear cover assembly
3
1
3
2
3
2
3
2
2
1
Cable routing: When you install the antenna kit, route the cables as shown in the following illustration. As
you route the cables, make sure that they are not subject to any tension. Tension could cause the cables to
be damaged by the cable guides, or a wire to be broken.
a Wireless WAN antenna, AUX (blue)
112 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
b Wireless LAN antenna, AUX (black)
c Wireless LAN antenna, 3rd (white)
d Wireless LAN antenna, MAIN (gray)
e Wireless WAN antenna, MAIN (red)
a
b
c
d
e
Chapter 10. Removing or replacing a FRU 113
Download from Www.Somanuals.com. All Manuals Search And Download.
114 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult
your local Lenovo representative for information on the products and services currently available in your
area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that
Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service
that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user’s
responsibility to evaluate and verify the operation of any other product, program, or service.
Lenovo may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document does not give you any license to these patents. You can send
license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow
disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply
to you.
This information could include technical inaccuracies or typographical errors. Changes are periodically
made to the information herein; these changes will be incorporated in new editions of the publication.
Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
The products described in this document are not intended for use in implantation or other life support
applications where malfunction may result in injury or death to persons. The information contained in this
document does not affect or change Lenovo product specifications or warranties. Nothing in this document
shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo
or third parties. All information contained in this document was obtained in specific environments and is
presented as an illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it believes appropriate without
incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in
any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of
the materials for this Lenovo product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled environment. Therefore, the result
obtained in other operating environments may vary significantly. Some measurements may have been
made on development-level systems and there is no guarantee that these measurements will be the same
on generally available systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their
specific environment.
© Copyright Lenovo 2012, 2013
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Electronic emission notices
For electronic emission information on Class B digital devices, refer to the corresponding information in
the User Guide.
Trademarks
The following terms are trademarks of Lenovo in the United States, other countries or both:
Active Protection System
Lenovo
ThinkLight
ThinkPad
ThinkVantage
TrackPoint
Ultrabay
UltraNav
Microsoft, Windows, and Windows Server are trademarks of the Microsoft group of companies.
Intel is a trademark of Intel Corporation in the U.S. and/or other countries.
Other company, product, or service names may be the trademarks or service marks of others.
116 Hardware Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Number: 0B48474_02
Printed in
(1P) P/N: 0B48474_02
*1P0B48474_02*
Download from Www.Somanuals.com. All Manuals Search And Download.
|
