T221 installation & system attachement information
Model recommendation
The primary consideration, for choosing either the T221 model DG3 or DG5 is the rate at which it is
desired to display image changes. Internal frame buffers within the T221 ensure that the panel is always
refreshed at a suitable rate (41Hz in the DG3, 41-48Hz in the DG5); however bandwidth and I/O
considerations on the DVI interface mean that the frame buffers may be updated with new data at a
slower rate. For many applications this isn’t an issue; however some applications require a higher rate so
that motion or data changes are presented as quickly and smoothly as possible.
The following table summaries the recommended T221 model and graphics card(s) depending on the
preferred update rate.
T221
Image
motion
characteristic
IBM Supported
Graphics Cards
(NVIDIA)
Minimum
Screen Update
Rate
Typical Applications
Firmware
level
Model EDID
Primarily
static
Office
Applications
Publishing
Virtual
Galleries &
FX1100
FX1300
2D
13Hz
DG3/5
29
Museums
Digital
Photography
FX1100
FX1300
DG3 – 4.0
DG5 – 4.3
20Hz
24Hz
DG3/5
DG5
29
02
Engineering
3D
& Modeling
FX3000
FX3400
Image
analysis
(roaming,
Video windowing,
leveling)
FX3000
FX3400
48Hz
DG5
06
Smooth &
life-like
Video
Creation
Document version 1.0
Page 1
9/1/2004
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
It's important to use the correct graphics card BIOS & device driver level when attaching the T221
When not pre-loaded, these are available from the IBM technical support web site (see http://www-
1.ibm.com/support/docview.wss?rs=0&q=9503&uid=psg1MIGR-39635) or the card supplier's support site
and are summarized below
Device driver (minimum level)
Graphics card
BIOS
Windows XP
Windows 2000
Linux
NVIDIA Quadro FX 3400
NVIDIA Quadro FX 1300
NVIDIA Quadro FX 4000
NVIDIA Quadro FX 3000
NVIDIA Quadro FX 2000
NVIDIA Quadro FX 1100
NVIDIA Quadro FX 600
NVIDIA Quadro4 980 XGL
NVIDIA Quadro4 900 XGL
ATI FireGL4
Standard
Standard
Standard
Standard
Standard
61.76 (IBM)
61.11 (NVIDIA)
Standard
Standard
4.28.20.19.15 (IBM)
4.25.00.29.25 (IBM)
1.26 (IBM)
6.12.10.2090 (IBM)
1.9.16 (ATI)
Note: The above device driver levels are the minimum required, it is generally advantageous to use the
latest level available.
Configuration
The input flexibility offered by the T221, allows it to be driven in a number of different ways. There are a
total of 4x single-link DVI inputs, however, operation from a single DVI input as a single monitor with a
single desktop is the most simple and is typical of industry standard monitor attachment. The bandwidth
of a single-link DVI channel is limited to a maximum pixel clock frequency of 165MHz, for the T221’s
3840x2400 resolution, this corresponds to an update rate of 13Hz
Note: Internal frame buffers in the T221 retime the input data and display it at a fixed 41Hz (for the DG3)
or 41-48Hz (for the DG5).
By driving more than one input, the update rate can be increased. This is summarized below.
Document version 1.0
Page 3
9/1/2004
Download from Www.Somanuals.com. All Manuals Search And Download.
T221 Model
Inputs
9503-DG3
9503-DG5
Single-link DVI (each, max 4)
- 165MHz pixel clock limit
- 495MB/sec (24bit RGB)
Single-link DVI (each, max 4)
- 165MHz pixel clock limit
- 495MB/sec (24bit RGB)
Dual-link DVI (1x), via converter box
- 330MHz pixel clock limit
- 990MB/sec (24bit RGB)
41-48Hz
Internal panel
refresh rate
41Hz
Main high resolution 1x DVI input = 3840x2400@13Hz
Dual-link DVI modes
modes
(recommended)
2x DVI input = 3840x2400@20Hz
4x DVI input = 3840x2400@41Hz
1x DVI input = 3840x2400@24Hz
Single-link DVI modes
1x DVI input = 3840x2400@13Hz
2x DVI input = 3840x2400@20Hz
2x DVI input = 3840x2400@24Hz
4x DVI input = 3840x2400@48Hz
Document version 1.0
Page 4
9/1/2004
Download from Www.Somanuals.com. All Manuals Search And Download.
Single monitor configurations.
1. Single monitor, single-link DVI (13Hz)
T221 (9503-DG3/5)
3840x2400@13Hz
Single-link DVI
Single-link DVI
not connected
NVIDIA Quadro4 980XGL
NVIDIA Quadro FX1000
NVIDIA Quadro FX3000
IntelliStation M/Z-Pro
Driver level
As per minimum level
Graphics cards As per supported list
T221 EDID
Update rate
Desktop
029 (default)
13Hz
Single
2. Single monitor, twin single-link DVI (20Hz)
T221 (9503-DG3/5)
3840x2400@20Hz
Single-link DVI
Single-link DVI
NVIDIA Quadro4 980XGL
NVIDIA Quadro FX1000
NVIDIA Quadro FX3000
IntelliStation M/Z-Pro
Driver level
As per minimum level
Graphics cards As per supported list
T221 EDID
Update rate
Desktop
029 (default)
20Hz
Single (horizontal span via NVIEW utility)
Dual view (extend desktop via OS)
Document version 1.0
Page 5
9/1/2004
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Single monitor, twin single-link DVI (24Hz, DG5 only)
T221 (9503-DG5)
3840x2400@24Hz
Single-link DVI
Single-link DVI
NVIDIA Quadro4 980XGL
NVIDIA Quadro FX1000
NVIDIA Quadro FX3000
IntelliStation M/Z-Pro
Driver level
As per minimum level
Graphics cards As per supported list
T221 EDID
Update rate
Desktop
034 (default)
24Hz
Single (horizontal span via NVIEW utility)
Dual view (extend desktop via OS)
4. Single monitor, dual-link DVI (24Hz, DG5 only)
T221 (9503-DG5)
3840x2400@24Hz
Dual-link DVI
not connected
Single-link DVI
NVIDIA Quadro FX3000
IntelliStation M/Z-Pro
Driver level
Minimum as per FX2000 or FX3000
Graphics cards FX2000 or FX3000 or FX4000 or FX3400
T221 EDID
Update rate
Desktop
002
24Hz
Single
(*) Note : Dual link converter should be connected to graphics card DVI connector that locates close to AGP or close to PCI express.
Document version 1.0
Page 6
9/1/2004
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Single monitor, single+dual-link DVI (48Hz, DG5 only)
T221 (9503-DG5)
3840x2400@48Hz
Dual-link DVI
Single-link DVI
NVIDIA Quadro FX3000
IntelliStation M/Z-Pro
Driver level
53.03
Graphics cards FX3000 or FX3400
T221 EDID
Update rate
Desktop
006
48Hz
Single (horizontal span via NVIEW utility)
(*) Note : Dual link converter should be connected to graphics card DVI connector that locates close to AGP or close to PCI express.
Multi-monitor configurations
1. Dual monitor configuration, twin single-link DVI (13Hz + 13Hz)
T221 (9503-DG3/5)
3840x2400@13Hz
Single-link DVI
NVIDIA Quadro FX3000
Single-link DVI
T221 (9503-DG3/5)
3840x2400@13Hz
IntelliStation M/Z-Pro
Driver level Minimum as per FX3000
Graphics
cards
FX3000
Note: other dual output cards can be used as per the supported list, however features such
as OpenGL, portrait operation etc. will be restricted due to memory limitations
Monitor 1
T221 EDID 029 (default)
Update rate 13Hz
Monitor 2
029 (default)
13Hz
Desktop
Single (horizontal span via NVIEW utility)
Dual view (extend desktop via OS)
Document version 1.0
Page 7
9/1/2004
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Dual monitor configuration, single + dual-link DVI (13Hz + 24Hz, DG5 only)
T221 (9503-DG5)
3840x2400@24Hz
Dual-link DVI
NVIDIA Quadro FX3000
Single-link DVI
T221 (9503-DG3/5)
3840x2400@13Hz
IntelliStation M/Z-Pro
Driver level Minimum as per FX3000 or FX3400
Graphics
cards
FX3000 or FX3400
Note: other supported dual output cards can be used, however full performance (OpenGL,
portrait operation etc.) will be limited due to available memory limitations
Monitor 1
002
Monitor 2
029 (default)
13Hz
T221 EDID
Update rate 24Hz
Desktop
Single (horizontal span via NVIEW utility), Dual view (extend desktop via OS)
(*) Note : Dual link converter should be connected to graphics card DVI connector that locates close to AGP or close to PCI express.
3. Dual monitor configuration, dual + dual-link DVI (24Hz + 24Hz, DG5 only)
T221 (9503-DG5)
3840x2400@24Hz
Dual-link DVI
NVIDIA Quadro
FX4000
T221 (9503-DG5)
3840x2400@24Hz
Dual-link DVI
IntelliStation M/Z-Pro
Driver level Minimum as per FX4000
Graphics
cards
FX4000
Note: other supported dual output cards can be used, however full performance (OpenGL,
portrait operation etc.) will be limited due to available memory limitations
Monitor 1
002
Monitor 2
002
T221 EDID
Update rate 24Hz
Desktop
24Hz
Single (horizontal span via NVIEW utility), Dual view (extend desktop via OS)
Document version 1.0
Page 8
9/1/2004
Download from Www.Somanuals.com. All Manuals Search And Download.
GUI & application optimization (Windows)
The very high resolution of the T221 means that features of the graphical user interface (GUI), such as
icons & fonts, become smaller. These can be adjusted through the 'display properties' window as per the
following instructions.
Note: Many of these settings are subjective, and some users may prefer values different than those
suggested here. Also, after these settings have been made, some application programs and system
dialog boxes may still not be scaled properly. For information concerning operating system graphical user
interface scaling features available to application developers, please contact Microsoft.
Win2000
1. Increase System Scaling Size (called Font Size)
Right click on the desktop background, and select properties to bring up the display properties window.
(The display properties window can also be launched by sequentially selecting start/settings/control
panel/display.) In sequence, select settings/advanced/general/font size/other. Set the font percentage to
213%, by typing in this number in the highlighted box. Click OK as necessary in the following pop-up
boxes and reboot. (It is necessary to reboot at this point because the following steps depend upon the
font setting.)
2. Increase Mouse Pointer Sizes
Launch Control Panel by sequentially selecting start/settings/control panel. Click on the mouse icon, then
select in sequence
Pointers/Scheme. Select Magnified from the list and click on OK.
3. Change other Windows Feature Sizes
As in step 1, launch Display Properties window, and select Appearance. Select the following items and
make changes according to the table. You will have to click on apply for each entry individually.
Item
Size
36
1
36
50
95
95
36
1
Font Size
8
Font
MS Sans Serif
Active Title Bar
Active Window Border
Caption Button
Icon
Icon Spacing Horizontal
Icon Spacing Vertical
Inactive Title Bar
Inactive Window Border
Menu
Message Box
Palette Title
Scroll Bar
Selected Items
Tooltip
8
8
MS Sans Serif
MS Sans Serif
31
8
8
8
MS Sans Serif
MS Sans Serif
MS Sans Serif
31
24
31
8
8
MS Sans Serif
MS Sans Serif
4. Change taskbar icon sizes.
Document version 1.0
Page 9
9/1/2004
Download from Www.Somanuals.com. All Manuals Search And Download.
The taskbar contains a start button typically in the lower left corner, with the task bar running along the
bottom of the screen. To the right of the start button are a number of quick launch icons for applications.
Right click anywhere in the quick launch portion of the taskbar, that is not on an icon. A pop-up menu
appears. Select view, then large. This increases the size of the quick launch icons.
5. Change Application user interface feature sizes.
Some applications, such as MS Office, Lotus Suite, and others allow icon sizes and other features to be
changed through user preferences dialog. If possible, choose large icons for each application. For some
applications, standard accessibility options provide an easy path to increasing icon size.
WinXP
1. Increase System Scaling Size (called Font Size).
Right click on the desktop background, and select properties to bring up the display properties window.
(The display properties window can also be launched by sequentially selecting start/settings/control
panel/display.) In sequence, select settings/advanced/general/DPI setting/custom setting. Set the custom
DPI setting to 213%, by typing in this number in the highlighted box. Click OK as necessary in the
following pop-up boxes, exit out of display properties dialog, and reboot. (It is necessary to reboot at this
point because the following steps depend upon the DPI setting.)
2. Change Windows Feature Sizes.
For WinXP, many user appearance settings change automatically when the DPI setting is changed. This
includes mouse pointer size. If you prefer an even larger mouse pointer, click on start, control panel,
mouse icon, pointers, scheme, and set to Magnified (system scheme) or another preferred choice. Here
are the default settings XP provides with DPI setting to 213% (204 ppi).
Item
Size
38
2
38
50
101
101
38
2
Font Size
8
Font
Tahoma
Active Title Bar
Active Window Border
Caption Buttons
Icon
Icon Spacing Horizontal
Icon Spacing Vertical
Inactive Title Bar
Inactive Window Border
Menu
Message Box
Palette Title
Scroll Bar
Selected Items
Tooltip
8
8
Tahoma
Tahoma
38
8
8
8
Tahoma
Tahoma
Tahoma
32
34
38
8
8
Tahoma
Tahoma
3. Change Application user interface feature sizes.
Some applications, such as MS Office, Lotus Suite, and others allow icon sizes and other features to be
changed through user preferences dialog. If possible, choose large icons for each application. For some
applications, standard accessibility options provide an easy path to increasing icon size.
Application dependent features
Document version 1.0
Page 10
9/1/2004
Download from Www.Somanuals.com. All Manuals Search And Download.
It may be necessary to adjust application settings (or, persuade the application developers to modify the
source code). The attached article from Microsoft explains this further:
"How to write High-DPI Applications" by Nick Kramer msdn.microsoft.com
Resolution Switching Utility
There may still be some cases were it's better to run applications at a lower resolution for some tasks,
and at high resolution for others. A Windows 2000/XP utility is available to enable 'on the fly' switching
between resolutions.
Color Management
The T221 incorporates a brightness & color calibration facility. This enables the brightness and color
characteristic of the monitor to be preset to match certain profiles.
A Windows 2000/XP utility is available which enables calibration profiles to be loaded into the T221.
The utility has been tested in conjunction with calibration hardware & software from GretagMacbeth and
IMAGE Smiths. The IMAGE Smiths VeriLUM tool supports T221 calibration to DICOM requirements.
Document version 1.0
Page 11
9/1/2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|