Machine type: 10086/3109/4743 K430
10089/1168/4744 K410
10090/2556/4748 K415
IdeaCentre K4 Series
User Guide
Version 1.0
2012.02
31501096
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
Before using this manual, it is important that you read and understand all of the
related safety information for this product. Refer to the Safety and Warranty Guide
that you received with this product for the latest safety information. Reading and
understanding this safety information reduces the risk of personal injury or damage
to your product.
Danger: Be aware of extremely hazardous or lethal situations.
Attention: Be aware of possible damage to programs, devices, or data.
Note: Pay attention to this important information.
© Copyright Lenovo 2012. All rights reserved.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered
pursuant a General Services Administration “GSA” contract, use, reproduction, or
disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
© 2012. Lenovo
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
Using the Computer Hardware
This chapter contains the following
topics:
Computer hardware introduction
Information on computer connections
Note: The descriptions in this chapter
might be different from what you see on
your computer, depending on the computer
models and configurations.
User Guide
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Front view of the chassis
Attention: Be careful not to block any air vents on the computer. Blocked
air vents can cause overheating.
Power button
Power Control Switch indicator ON/OFF (selected models only)
Hard disk drive indicator
Power control switch (selected models only)
Memory card readers (selected models only)
USB connector
Microphone connector
Headphone connector
Optical drive (some models are equipped with only one optical drive)
Hot plug HDD port (selected models only)
Attention: Do not insert 3-inch discs into the optical drive.
2
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 Rear view of the chassis
IdeaCentre K430
Voltage selection switch (selected models only)
Power connector
HDMI connector (selected models only)
USB connectors
DisplayPort connector (selected models only)
On-board VGA connector
Ethernet connector
Audio connectors
PCI Express X 16 graphics adapter connector (some models are equipped
with a graphics card)
PCI Express X 1 adapter connector (some models are equipped with a WIFI
card or TV tuner card)
User Guide
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IdeaCentre K410
Voltage selection switch (selected models only)
Power connector
USB connectors
HDMI connector (selected models only)
On-board VGA connector
Ethernet connector
Audio connectors
PCI Express X 16 graphics adapter connector (some models are equipped
with a graphics card)
PCI Express X 1 adapter connector (some models are equipped with a WIFI
card or TV tuner card)
4
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
IdeaCentre K415
Voltage selection switch (selected models only)
Power connector
USB connectors (USB ports 4 to 6)
HDMI connector (selected models only)
On-board VGA connector
Ethernet connector
Audio connectors
PCI Express X 16 graphics adapter connector (some models are equipped
with a graphics card)
PCI Express X 1 adapter connector (some models are equipped with a WIFI
card or TV tuner card)
User Guide
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Connecting your computer
Note: Your computer may not have all of the connectors described in this
section.
1.3.1 Check the position of the voltage-selection switch on
the rear of the computer. Use a ballpoint pen to slide the
switch if necessary.
Note: Some computers do not have a voltage switch. These computers
control voltage automatically.
•
•
If the voltage supply range is 100-127 V AC, set the switch to 115 V.
If the voltage supply range is 200-240 V AC, set the switch to 230 V.
230
115
1.3.2 Basic connector instructions
Connector
Description
Microphone
Use this connector to attach a microphone to your
computer when you want to record sound or if you
use speech-recognition software.
Headphone
Use this connector to attach headphones to your
computer when you want to listen to music or
other sounds without disturbing anyone.
Audio line-in connector
Used to receive audio signals from an external
audio device, such as a stereo system. When
you attach an external audio device, a cable is
connected between the audio line-out connector
of the device and the audio line-in connector of
the computer.
6
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio line-out connector
Used to send audio signals from the computer
to external devices, such as powered stereo
speakers (speakers with built-in amplifiers),
headphones, multimedia keyboards, or the audio
line-in connector on a stereo system or other
external recording device.
USB connector
Use this connector to attach a device that requires
a USB connection.
Ethernet connector
VGA connector
Use this connector to attach the computer to an
Ethernet-type local area network.
Used to attach a VGA monitor or other devices
that use a VGA monitor connector.
DVI connector
Used to attach a DVI monitor or other devices that
use a DVI monitor connector.
HDMI connector (optional)
Connects to the HDMI connector on your display
or TV.
DisplayPort connector
(optional)
Used to attach a high-performance monitor, a
direct-drive monitor, or other devices that use a
DisplayPort connector.
TV-Tuner connector (optional) Only supported on systems with optional TV tuner
card.
Note: If your computer is equipped with a wireless keyboard or mouse,
follow the installation instructions for those devices.
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
7
1.4 7.1 Audio configuration instructions
Use the following illustration when connecting a 7.1 surround sound audio system:
S/PDIF out connector
Microphone input Connector
Audio line-out Connector
Center / Low frequency output
connector
Surround out connector
Audio line-in Connector
Note: For more detailed settings, click Start → Control panel → Hardware
and Sound → Lenovo HD Audio Manager. Follow the instructions to
configure advanced settings.
Sound configuration is as follows:
1. Right click the Sound icon in the system property bar and select the sounds
option to setup the sounds in the pop-up dialog box.
2. Select a playback device from the playback dialog box, then click the
configure button to configure it.
3. Select 7.1 surround from audio channels in the pop-up speaker setup dialog
box and proceed with the speaker setup by following the prompts.
8
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
4. 7.1 surround sound can be used once this configuration procedure is complete.
Note: If the audio configuration interfaces above are different from
those on your computer, you may use the above steps as a reference to
configure the 7.1 surround sound audio device system in your actual audio
configuration interface and read the electronic Help information for further
assistance.
1.5 5.1 Audio configuration instructions
(This instruction is only for the pc model which
mainboard supports audio transforming from 2.0 stereo
to 5.1 surround.)
This model of computer supports transforming stereo sound into 5.1 surround
sound.
Use the following guides when connecting to the 5.1 surround audio device:
Blue line-in connector
Surround
Green line-out connector
Front channel
Pink Mic-in connector
Center-LEF
The configurations are as followings:
1. Right click the Sound icon in system property bar and select sounds option to
setup the sounds in the pop-up dialog box.
2. Select a playback device from the playback dialog box, and then click configure
button to configure it.
3. Select 5.1 surround from audio channels in the pop-up speaker setup dialog
box to proceed with the speaker setup by following as prompted.
4. After the configuration, 5.1 surround can be used.
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Note: If the audio configuration interfaces in above are different from your
actual computer, you may use above steps as reference to configure the
5.1 surround audio device in your actual audio configuration interface and
read the electronic Help information for further assistance.
1.6 Connect the power cords properly to grounded
electrical outlets
1.7 How to play Blu-ray Discs (selected models only)
Check the connectors available on your computer and display and select an
appropriate cable according to this table. Because other types of cables do not
meet the requirements of the Blu-ray standard.
You need to purchase the cable separately if the computer is not equipped with
the corresponding cable.
This table will help you to identify the connectors on your computer and display.
Connection Type Computer
Cable
Display
DVI to DVI
(DVI cable)
ꢀ
DVI to HDMI
(DVI-HDMI
cable)
ꢀ
HDMI to HDMI
(HDMI cable)
ꢀ
HDMI to DVI
(HDMI-DVI
cable)
ꢀ
10 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
1.8 Wired keyboard (selected models only)
LVT —— After entering Windows, press this key to launch the LVT (Lenovo
Vantage Technology) program, Lenovo’s pre-loaded Home PC software.
In addition to its own functions, the LVT program will allow you to start
other Windows compatible software, specially configured to run on this
model of computer.
F2 —— Your computer has the Lenovo Rescue System installed. To learn more
about this program, repeatedly press and release the F2 key once
turning on the computer until the Lenovo Rescue System open.
1.9 Hot-swappable hard disk (selected models only)
•
Unpack
Hot-swappable hard disk
USB adapter
USB cable
You may plug the hot-swappable hard disk conveniently while the computer
system using it remains in operation, but will not damage the hard disk data.
You may back up the data on this hot-swappable hard disk at any time for data
maintenance or data transmission.
User Guide 11
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Operation of the hot-swappable hard disk
Slide it into the bay from the front until it snaps into position.
Pull the hot-swappable hard disk drive out of the drive bay.
12 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Connect the hot-swappable hard disk to the other computer
Notes:
• Don’t unplug the hard disk while it is copying the data to avoid result in
a loss of data.
• After installing the hard disk and connecting all the cables, wait for a
moment to make the system distinguish from the hard disk.
• Don’t install the operating system on the hot-swappable hard disk.
• Don’t unplug the hard disk while it is operating a software program to
avoid collapse of system.
• After pulling out the hard disk, don’t beat the hard disk or throw it
everywhere to damage it.
• Under the Rescue System, each function mode cannot distinguish from
the hot-swappable hard disk.
User Guide 13
Download from Www.Somanuals.com. All Manuals Search And Download.
1.10 Power Control Switch (selected models only)
The Power Control Switch feature allows your computer to switch to different
modes, thus providing you with customized experiences during operations.
Operation of the Power Control Switch
The Power Control Switch function supports three operating modes: Auto, Turbo
and Cool. System resources are optimized by toggling between those three
different modes. Different modes are used for different applications.
In the Auto and Cool mode, computer will boot up at rapid speed; In the Turbo
mode, computer will boot up at ultra speed.
•
Switch different mode by toggling the power control switch
14 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Press the Power Control Switch indicator ON/OFF to open the indicator under
the front panel and indicate the different lighting effects in each mode.
•
Display the main screen of the software
Double click the Power Control Switch icon in the Quick Launch bar.
Open the running status for
each component under the
Mode Switch:
CPU — Show the
percentage of
the current CPU
clock frequency
against the nominal
maximal CPU clock
frequency.
Boot — The status of the
computer startup
speed.
User Guide 15
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO
Auto adjust the system CPU
clock frequency and running
speed. Turn the Power
Control Switch knob to the
Auto position to enable this
mode.
Note:
The numeric values may
vary because each model is
configured differently.
COOL
The CPU runs at low
frequency. The system
consumes minimum power.
Turn the Power Control
Switch knob to the Cool
position to enable this mode.
16 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Note:
The numeric values may
vary because each model is
configured differently.
TURBO
The CPU runs at full speed.
The system achieves its
optimal performance. Turn
the Power Control Switch
knob to the Turbo position to
enable this mode.
Note:
The numeric values may
vary because each model is
configured differently.
User Guide 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
• When you are running system-intensive games or other programs that
consume a high proportion of the system resources, you should choose
Turbo mode. This will allow you to achieve optimal performance.
• After unplugging and reconnecting the power cord to the outlet, the
computer cannot boot up at ultra speed in Turbo mode. In order to
keep ultra speed during the boot up, the computer must always keep
connecting the outlet.
18 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
Using the Rescue System
This chapter contains the following
topics:
OneKey Recovery
Driver and Application Installation
System Setup
System Backup
System Recovery
Create Recovery Disc
Attention: Using this program will result in
loss of data.
•
You can restore the C: drive of the computer
to factory default settings or to the last
system backup status using OneKey
Recovery. If you do this, all of the existing
data on drive C: will be lost, but the content
and format of the other partitions of the hard
disk drive will remain unchanged.
•
If you want to install an operating system
and back it up with OneKey Recovery, you
must format the C: partition in NTFS format
and install the operating system on the C:
partition. Otherwise, the OneKey Recovery
system cannot run.
User Guide 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Note about the service partition:
The files and relevant data used by the rescue system are saved in the service
partition. Deleting this partition will make the rescue system unusable. For more
detailed information, see the following instructions:
By selecting Control Panel → Administrative Tools → Computer Management
→ Disk Management, you can see the service partition, which must not be
deleted.
Note: The recovery files and relevant data used by the rescue system are
saved in the service partition. If the service partition is deleted or damaged
by someone other than authorized Lenovo service personnel, Lenovo will
not be liable for any losses arising therefrom in any way.
2.1 OneKey Recovery
OneKey Recovery is an easy-to-use application. You can use it to restore your
computer to the system default or to a previously backed up state.
Detailed Operation Procedure
1. Repeatedly press and release the F2 key once turning on the computer until
the Lenovo Rescue System open, then select OneKey Recovery.
Note: System Recovery will overwrite all of the data on the C: drive. To
prevent loss of data, be sure to back up relevant data before performing
system recovery.
2. Follow the on-screen instructions to select the backup task you want to restore
from and the disk where you want to install the operating system, then press
Next to start the restore.
3. Please wait during the process of system recovery. Do not interrupt the
operation during the recovery process.
4. After the system is recovered successfully, the software will prompt you to
restart the computer. Restart the computer and start the operating system.
2.2 Driver and Application Installation
The Driver and Application Installation function in the rescue system provides a
way for the user to conveniently reinstall all of the Lenovo applications and drivers
that were shipped with your Lenovo hardware.
20 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Method 1: Automatic Installation
Repeatedly press and release the F2 key once turning on the computer until the
Lenovo Rescue System open, then select Drivers and Application Installation.
Follow the on-screen prompts to install the Lenovo drivers and applications.
Click Install to start installing the Lenovo Drivers and Application Installation
software.
The system will restart. After the system has restarted, the installation process will
continue until it has completed.
Method 2: Manual Installation
In the Windows system, Click Start → All Programs → Lenovo → Lenovo
Drivers and Application Installation.
After starting the procedure, install all the drivers and software manually by
following the prompts.
Notes:
1. Do not install software which is already installed on the computer.
2. Make sure that the Drivers and Application Installation software has
been automatically installed before starting the operating system. The
manual installation function can only be used after the software has
been installed.
2.3 System Setup
System Setup configures the network configuration for the Lenovo Rescue
System to ensure your Rescue System can connect to internet. In addition, System
Setup sets and manages all passwords for the Lenovo Rescue system.
2.3.1 Launch
Repeatedly press and release the F2 key once turning on the computer until the
Lenovo Rescue System open, then select System Setup.
2.3.2 Network Settings
Depending on the network access mode of the computer, select “ADSL” or “LAN
Connection” in the network connection modes.
1. If you select “ADSL” input the username and password of the ADSL
connection.
User Guide 21
Download from Www.Somanuals.com. All Manuals Search And Download.
2. If you select “LAN connection” configure the IP address and proxy server of the
LAN.
2.3.3 Password Management
Password Management allows you to set and manage the password for Lenovo
Rescue System.
The default password is blank.
Set a password when you access Password Management for the first time.
If you don’t want to set a password, access the system directly and operate it
accordingly.
2.4 System Backup
This backs up your system partition to an image file. In case of a system failure,
you can restore your system from this image file.
In the Windows system, click Start → All Programs → Lenovo → Lenovo
Rescue System.
After starting Rescue System, click System Backup to back up your system
partition by following the prompts.
2.5 System Recovery
Reboot your computer into the system recovery environment. You can choose to
restore to a system backup point or the initial state (factory default settings).
2.6 Create Recovery Disc
Create a bootable recovery disc from the current system. These recovery discs
are used to boot your computer and will guide you through the entire restoration
process.
In the Windows system, click Start → All Programs → Lenovo → Lenovo
Rescue System.
After starting Rescue System, click Create Recovery Disc to create a bootable
recovery disc from the current system.
Follow the on-screen prompts to create recovery discs.
22 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting and
Confirming Setup
Chapter
This chapter contains the following
topics:
Troubleshooting and Problem Resolution
Note: The description of the TV tuner card
in this manual is only used for the machines
which have the TV tuner card. It does not
apply to those machines that do not have a
TV tuner card.
User Guide 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
Follow these tips when troubleshooting your computer:
•
•
•
If you added or removed a part before the problem started, review the
installation procedures to ensure that the part is correctly installed.
If a peripheral device does not work, ensure that the device is properly
connected.
If an error message appears on the screen, write down the exact message.
This message may help support personnel diagnose and fix the problem(s).
If an error message occurs in a program, see the program’s documentation.
•
Note: The procedures in this document were written for the Windows
default view, so they may not apply if you set your Lenovo® computer to
the Windows Classic view.
3.1 Troubleshooting Display Problems
Problem: Blank screen or no image is displayed on the monitor.
Troubleshooting and problem resolution:
1. Check to see if the monitor has been turned on; if not, press the Power button.
2. Check to see if the monitor power cord is loose; if so, plug the power cord
securely into the monitor.
3. Check to see if the signal cable to the monitor is securely connected to the
connector on the computer graphics card; if not, shut down the computer
then connect the signal cable of the monitor securely to the connector on the
computer graphics card.
Problem: You need to change the display property settings.
Setting display background and icon properties:
1. Right-click the desktop anywhere except over an icon, then select Personalize
from the pop-up menu.
2. From here, select the appropriate options to:
•
•
•
•
Change the desktop background
Select a screen saver
Select colors and appearance options for icons and text
Set resolution and colors in the Display Settings options
24 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem: Ripple on screen.
Troubleshooting and problem resolution:
1. Check to see if any of the following devices are located less than one meter
from the computer: refrigerators, electric fans, electric dryers, UPS systems,
regulators, fluorescent lamps or other computers that may be generating
magnetic interference.
2. Move any interfering devices away from the computer.
3. If the problem persists, contact Lenovo Service.
3.2 Troubleshooting Audio Problems
Problem: No sound from the integrated speakers.
Troubleshooting and problem resolution:
•
Adjust the Windows volume control — double-click the speaker icon in the
lower-right corner of your screen. Ensure that the volume is turned up and the
sound is not muted. Adjust the volume, bass, or treble controls to eliminate
distortion.
•
•
Reinstall the audio driver.
Disconnect any headphones from the headphone connector — sound from
the speakers is automatically disabled when headphones are connected to the
computer’s side-panel headphone connector.
Problem: No sound from headphones.
Troubleshooting and problem resolution:
•
Check the headphone cable connection — ensure that the headphone cable is
securely inserted into the headphone connector.
•
Adjust the Windows volume control — click or double-click the speaker icon in
the lower-right corner of your screen. Ensure that the volume is turned up and
the sound is not muted.
3.3 Troubleshooting Software Problems
Problem: You are unable exit a running program normally.
Troubleshooting and problem resolution:
1. Open the Task Manager window by pressing Ctrl, Alt and Delete at the same
time.
2. Select the Application tab, select the problem program, then click the End
Task button.
User Guide 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem: You need to install or uninstall a program.
Problem resolution:
During installation never abort the install process by powering the system off or
through other drastic means. This can cause system program disorder or even
failure during system initialization.
During the uninstall process, never directly delete the files or folders. This is
harmful to the system, and might cause a system-wide malfunction.
Use the following procedure to properly uninstall programs:
1. Back up all documents and system settings related to the program before
removing it.
2. If the program has its own uninstaller, run it directly to uninstall the program.
3. If the program does not have its own uninstaller, then select Control Panel from
the Start menu.
4. From the Control Panel, choose Programs and Functions.
5. Find the applicable program from the Programs and Functions dialog box and
then select Uninstall/Modify.
6. Perform the instructions displayed to uninstall the software.
3.4 Troubleshooting Problems with Optical Drives and
Hard Disks
Problem: The Optical drive is unable to read a CD/DVD.
Troubleshooting and problem resolution:
1. Check to determine if there is an optical drive icon in the resource manager
of the operating system. If not, restart your computer. If there is still no icon,
contact Lenovo Service. Otherwise, continue with the next step of this
procedure.
2. Confirm that the CD/DVD has been properly placed in the drive. If not, reload
the CD or DVD. Otherwise, continue with the next step of this procedure.
3. Check the specifications that came with your computer to confirm that this
optical drive is capable of reading this type of CD or DVD.
4. If the CD/DVD cannot be read, replace it with a known good CD/DVD such as
one that was shipped with the computer.
5. If the known good CD cannot be read, visually check the operating side of the
CD/DVD for defects.
26 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem: The capacity of the hard disk, as indicated by the system, is less than
the nominal capacity.
Troubleshooting and problem resolution: For computers equipped with the
OneKey Recovery feature, the system recovery feature needs to occupy some
hard disk space. This may account for the apparent hard disk capacity deficit.
Further Technical Explanation: The nominal capacity of the hard disk is
expressed in the decimal system, 1000 bytes. But the actual hard disk capacity is
expressed in the binary system as 1024 bytes (For example, the nominal capacity
1G is 1000M, while the actual capacity 1G is 1024M).
The capacity of the hard disk shown in Windows can be calculated according to
the calculations in the following example:
The nominal capacity of the hard disk is 40G, while its actual capacity
should be: 40 x 1000 x 1000 x 1000/(1024 x 1024 x 1024) = 37G.
If the Service partition of 3G - 3 x 1000 x 1000 x 1000/(1024 x 1024 x 1024)
= 2.79G is subtracted, the capacity of the hard disk shown in the system
can be obtained.
The capacity of the hard disk as calculated using this method may be slightly
different from the actual capacity due to the rounding of totals.
3.5 Special considerations for troubleshooting
Windows
Record the following information as it may be useful later when troubleshooting
system problems:
1. The serial number of the software. The serial number was shipped with the
computer and provided separately by the manufacturer. The Help Center is
unable to retrieve this number.
2. The drivers for this computer model only support the Windows 7 system.
3. When you use the Windows Media Center to watch TV, be particularly attentive
to the following:
•
In the following two situations, you must re-save a channel list:
a. When you change your TV signal from digital to analog, your saved
channel list for digital TV is deleted. When you want to watch digital TV
again, you must create and save a new channel list.
b. When you change your TV signal from analog to digital, your saved
channel list for analog TV is deleted. When you want to watch analog
User Guide 27
Download from Www.Somanuals.com. All Manuals Search And Download.
TV again, you must create and save a new channel list.
•
You must set the TV tuner input signal to analog before you can watch
Teletext programming.
3.6 Performing Daily Maintenance Tasks
Cleaning the computer components
Because many of the computer components consist of sophisticated integrated
circuit boards, it is very important to periodically clean the computer to prevent
dust buildup. The cleaning supplies you need to clean the components include:
a vacuum cleaner, a soft cotton cloth, clear water (preferably purified or distilled
water) and cotton swabs.
Attention: Before you clean your computer, disconnect the computer
from the electrical outlet. Clean your computer with a soft cloth
dampened with water. Do not use liquid or aerosol cleaners, which may
contain flammable substances.
Note: To avoid damaging the computer or display, do not spray cleaning
solution directly onto the display. Only use products specifically designed
for cleaning displays, and follow the instructions included with the product.
The following are general methods for cleaning the components:
•
You can use a soft cloth to remove dust on the surface of the computer, the
monitor, the printer, the speakers and the mouse.
•
•
You can use a vacuum cleaner to clean in otherwise inaccessible corners.
To clean the keyboard thoroughly, shut down the computer and scrub it gently
with a wet cloth. Do not use the keyboard until it is dry.
Do not do any of the following:
•
•
•
Allow water to enter the computer.
Use a heavily dampened cloth.
Spray water directly onto the surface of the monitor or inside the computer.
LCD monitors should be cleaned daily. Use a dry cloth to brush dust from the
monitor and keyboard every day. Keep all surfaces clean and free of grease stains.
28 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
Hardware Replacement Guide
This chapter contains the following
topics:
Identifying internal components
Identifying parts on the system board
Removing the computer cover
Removing the front bezel
Replacing a memory module
Replacing a hard disk drive
Replacing an optical drive
Replacing a graphics card
Replacing the TV-Tuner card
Replacing the keyboard and mouse
User Guide 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
This guide is intended to be used by customers who are replacing Customer
Replaceable Units (CRUs) as well as trained service personnel who are replacing
Field Replaceable Units (FRUs). In this guide, CRUs and FRUs will often be referred
to as parts.
Note: Trained service personnel should refer to the Hardware Maintenance
Manual (HMM) for parts ordering information.
This guide does not include procedures for the replacement of all parts. It is
expected that trained service personnel are already able to replace cables,
switches, and certain mechanical parts without the need for step-by-step
procedures.
Note: Use only parts provided by Lenovo®.
The description of the TV-Tuner card in this manual applies only to computer
models with a TV-Tuner card, and therefore does not apply to models without a
TV-Tuner card.
This guide contains instructions for replacing the following parts:
•
•
•
•
•
Memory modules
Hard disk drive
Optical disk drive
Graphics card
TV-Tuner card
Safety information for replacing CRUs
Do not open your computer or attempt any repairs before reading the “Important
safety information” in the Safety and Warranty Guide that was included with your
computer. An electronic copy of the Safety and Warranty Guide can also be
obtained online from the Lenovo® Support Web site at:
30 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information resources
The most up-to-date information for your computer is available online at:
You can find the following information:
•
•
•
•
•
Customer replacement unit removal and installation information
Publications
Troubleshooting information
Parts information
Links to other useful sources of information
Tools required
To disassemble the computer, you will need the following tools:
•
•
•
•
•
•
Wrist grounding strap and conductive mat for preventing electrostatic discharge
Flat screwdriver
Phillips screwdriver
Hex screwdriver
Plastic flat screwdriver
Plastic tweezers
Note: The screws used for the different components vary in size. During
the disassembly procedure, group the screws with their corresponding
components to avoid a mismatch when replacing the components.
User Guide 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Handling static-sensitive devices
Static electricity, although harmless to you, can seriously damage computer
components.
When replacing a part, do not open the anti-static packaging containing the new
part until the defective part has been removed from the computer and you are
ready to install the new part.
When handling parts and other computer components, the following precautions
should be taken in order to avoid static electricity damage:
•
•
Limit your movements, as movement can cause the build-up of static electricity.
Always handle parts and other computer components with care, and handle
adapters, memory modules, system boards, and microprocessors by their
edges. Never touch any exposed circuitry.
•
•
Prevent others from touching parts and other computer components.
Before replacing a new part, first place the anti-static packaging containing the
part against a metal expansion slot cover or other unpainted metal surface on
the computer for at least two seconds. This will reduce static electricity in the
package and your body.
•
•
When possible, remove the new part from its anti-static packaging and install it
directly into the computer without setting the part down. If this is not possible,
place the part on top of its anti-static packaging on a smooth, flat surface
before installing it.
Do not place parts on the computer cover or other metal surface.
32 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Locations
4.1.1 Identifying internal components
The following illustration shows the components inside your computer.
1
2
3
4
6
5
Optical disk drive
Graphics card
System fan
Hard disk drive
System board
Power supply
User Guide 33
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1.2 Identifying parts on the system board
The system board (also known as the “mainboard” or “motherboard”) is the main
circuit board in your computer. It provides basic computer functions and supports
a variety of devices that are factory-installed or that you can install later.
The following illustrations show the locations of the different parts on the system
board.
Lenovo K430
1
2
3
4
5
6
7
17 16 15
14 13 12
11
10
9
8
12V power connector
Microprocessor fan header
Power connector
Microprocessor and heat sink
Memory slots (4)
Front USB header
PCI express X 16 adapter slots (2)
Power fan header
34 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel connector
Front USB connector
Serial (COM2) connector
Front audio connector
System fan header
Front USB connector
Mode switch connector
Battery
PCI express X 1 adapter slots (2)
Lenovo K410
1
2
3
4
5
6
7
8
9
20 19 18 17 16 15 14
13
12 11 10
12V power connector
Microprocessor fan header
Thermal sensor header
Battery
Microprocessor and heat sink
Memory slots (2)
Power connector
SATA connectors (3)
User Guide 35
Download from Www.Somanuals.com. All Manuals Search And Download.
eSATA connector
Power fan header
Front panel connector
Clear CMOS jumper
Mini PCI-E slot
Front USB connectors (2)
Mode switch connector
PCI express X 1 adapter slots (3)
PCI express X 16 adapter slot
Serial (COM2) connector
Front audio connector
System fan header
Lenovo K415
1
2
3
4
5
6
7
8
9
10
11
12
13
25 24 23 22 21
20 19
18
17 16 15
14
12V power connector
Battery
Microprocessor and heat sink
Memory slots (4)
Microprocessor fan header
Thermal sensor header
36 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Mini PCI-E slot
Power connector
eSATA connector
Power fan header
SSD power connector (Optional)
SATA connectors (4)
Front panel connector
Mode switch connector
ROM socket
LPC debug connector
Serial (COM2) connector
SPI debug connector
Front USB connector (2)
Clear CMOS jumper
Front USB header
PCI express X 1 adapter slots (3)
PCI express X 16 adapter slot
Front audio connector
System fan header
4.2 Replacing hardware
Attention: Do not remove the computer cover or attempt any repair
before reading the “Important safety information” in the Safety and
Warranty Guide that was included with your computer or in the Hardware
Maintenance Manual (HMM) for the computer. To obtain copies of the
Safety and Warranty Guide or HMM, go to the Support Web site at
4.2.1 General information
Pre-disassembly instructions
Before proceeding with the disassembly procedure, make sure that you do the
following:
1. Turn off the power to the system and all peripherals.
2. Unplug all power and signal cables from the computer.
3. Place the system on a flat, stable surface.
User Guide 37
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2.2 Removing the computer cover
Attention:
• Turn off the computer and wait 3 to 5 minutes to let it cool down
before removing the cover.
• For this procedure, it helps to lay the computer on a flat, stable
surface.
To remove the computer cover:
1. Remove any media (disks, CDs, or memory cards) from the drives, shut down
the computer, and turn off all attached devices.
2. Unplug all power cords from electrical outlets.
3. Disconnect all cables attached to the computer. This includes power cords,
input/output (I/O) cables, and any other cables that are connected to the
computer. Refer to “Locating connectors on the rear of the computer”.
4. Remove the two screws that secure the computer cover at the rear of the
chassis.
5. Slide the computer cover out to remove it.
38 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2.3 Removing the front bezel
Note: For this procedure, it helps to lay the computer on a flat, stable
surface.
To remove the front bezel:
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Remove the front bezel by releasing the three plastic tabs inside the chassis
and sliding the bezel out as shown.
3. To reattach the bezel, align the plastic tabs on the bottom of the bezel with the
corresponding holes in the chassis, and then snap it into position.
User Guide 39
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2.4 Replacing a memory module
Note: For this procedure, it helps to lay the computer on a flat, stable
surface.
To replace a memory module:
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Locate the memory module connectors. Refer to “Locating components”.
3. Remove the memory module to be replaced by opening the retaining clips as
shown.
4. Position the new memory module over the memory connector. Make sure
that the notch
key on the system board. Push the memory module straight down into the
connector until the retaining clips close.
on the memory module aligns correctly with the connector
5. Reattach the computer cover.
40 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2.5 Replacing a hard disk drive
Note: For this procedure, it helps to lay the computer on a flat, stable
surface.
To replace a hard disk drive:
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Disconnect the data and power cables from the hard disk drive.
3. Lift up the plastic handle and slide the hard disk drive out of the drive bay.
1
2
4. Remove the hard disk drive from the plastic bracket as shown.
5. Line up the new hard disk drive with the plastic bracket and snap it into position.
User Guide 41
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Slide the new hard disk drive into the drive bay and slide the drive bay into
place.
7. Connect the power and signal cables to the new hard disk drive.
8. Reattach the computer cover.
4.2.6 Replacing an optical drive
Note: For this procedure, it helps to lay the computer on a flat, stable
surface.
To replace an optical drive:
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Remove the front bezel. Refer to “Removing the front bezel”.
3. Disconnect the data and power cables from the rear of the optical drive.
4. Press the release button and push the optical drive straight out of the front of
the chassis.
1
2
3
5. Slide the new optical drive into the bay from the front until it snaps into position.
6. Connect the data and power cables to the new disk drive.
7. Reattach the front bezel and computer cover.
42 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2.7 Replacing a graphics card
Note: For this procedure, it helps to lay the computer on a flat, stable
surface.
To replace a graphics card:
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Follow the below steps to remove a graphics card:
If your computer has a Duo-graphics cards installed, follow the steps
below to replace it:
a. Remove the screw that secures the Duo-graphics cards fixing bracket and
lift the bracket up.
User Guide 43
Download from Www.Somanuals.com. All Manuals Search And Download.
b. Remove the screw that secures the graphics card latch to the chassis,
open it, and remove the Duo-graphics cards connector.
c. Remove the screw that secures the graphics card to the chassis.
4
3
2
1
d. Remove the graphics card by pulling it straight out of the connector.
44 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
If your computer has a single graphics card installed, follow the steps
below to replace it:
a. Remove the screw that secures the graphics latch to the chassis and open
it.
b. Remove the screw that secures the graphics card to the chassis.
3
2
1
c. Remove the graphics card by pulling it straight out of the connector.
User Guide 45
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Install the new adapter into the same adapter connector and secure it to
chassis with the screw.
4. Turn the graphics card latch to the closed position and secure it with the screw.
5. Connect the two graphics cards with the Duo-graphics cards connector and
reattach the Duo-graphics cards fixing bracket to the chassis. (For models with
Duo-graphics cards only)
6. Reattach the computer cover.
4.2.8 Replacing the TV-Tuner card
Note: For this procedure, it helps to lay the computer on a flat, stable
surface.
To replace the TV-Tuner card:
1. Remove the computer cover. Refer to “Removing the computer cover”.
2. Remove the screw that secures the graphics card latch to the chassis and
open it.
3. Remove the screw that secures the TV-tuner card to the chassis.
3
2
1
46 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Remove the TV-Tuner card by pulling it straight out of the connector.
5. Install the new TV-tuner into the same connector and secure it to chassis with
the screw.
6. Turn the graphics card latch to the closed position and secure it with the screw.
7. Reattach the computer cover.
User Guide 47
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2.9 Replacing the keyboard and mouse
Note: Your keyboard will be connected to a USB connector at either front
or the rear of the computer.
To replace the keyboard:
1. Remove any media (disks, CDs, or memory cards) from the drives, shut down
the computer, and turn off all attached devices.
2. Unplug all power cords from electrical outlets.
3. Locate the connector for the keyboard. Refer to “Front view of the chassis” and
“Rear view of the chassis”.
4. Disconnect the defective keyboard cable from the computer and connect the
new keyboard cable to the same connector.
5. The mouse can be replaced using the same method.
48 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix.
Declaration
Thank you for using Lenovo products.
Carefully read all documents shipped with your computer before you install and
use the product for the first time. Lenovo is not responsible for any loss except
when caused by installation and operations performed by Lenovo professional
service personnel. You are responsible if you fail to operate the product according
to instructions and requirements in the manuals included with your computer, or
operate the product inappropriately.
This manual could include technical inaccuracies or typographical errors. Changes
are made periodically to the information herein; these changes will be incorporated
in new editions of the publication.To provide better service, Lenovo reserves the
right to improve and/or modify the products and software programs described in
the manuals included with your computer, and the content of the manual, at any
time without additional notice.
The manuals included with your computer are provided to help you use Lenovo’s
products appropriately. For the configuration of the product, refer to the related
contract (if any) or product packing list, or consult the distributor for the product
sales.
The content of the manuals included with your computer is protected by copyright
laws and rules. None of the manuals included with your computer may be
reproduced or transcribed by any means or translated into any language without
prior written permission of Lenovo.
The software interface and function and hardware configuration described in
the manuals included with your computer might not match exactly the actual
configuration of the computer that you purchase.You are welcome to contact us
about the manuals included with your computer. For the latest information or any
questions or comments, contact or visit the Lenovo Web site:
User Guide 49
Download from Www.Somanuals.com. All Manuals Search And Download.
Trademarks
Lenovo and the Lenovo logo, IdeaCentre and IdeaCentre logo are trademarks of
Lenovo in the United States, other countries, or both.
Microsoft, Windows, and Windows Vista are trademarks of the Microsoft group of
companies.
Intel Inside is a trademark of Intel Corporation in the U.S. and/or other countries.
AMD, the AMD Arrow logo, ATI, AMD Athlon, AMD LIVE!, AMD Opteron, AMD
Phenom, AMD Sempron, Catalyst, Cool ‘n’ Quiet, CrossFire, PowerPlay, Radeon,
and The Ultimate Visual Experience are trademarks of Advanced Micro Devices,
Inc.
Other company, product, or service names referred to herein or in other Lenovo
publications may be trademarks or service marks of others.
All rights reserved.
Names or marks of certain companies mentioned in the manuals included with
your computer or this document do not necessarily indicate that related software
or hardware is included. The actual configuration of the product depends on the
packing list description.
Energy Star Statement
ENERGY STAR® is a joint program of the U.S. Environmental Protection Agency
and the U.S. Department of Energy aimed at saving money and protecting the
environment through energy efficient products and practices.
Lenovo is proud to offer our customers products with an ENERGY STAR compliant
designation. The following machine types have been designed and tested to
conform to the ENERGY STAR program requirement for computers at the time
of manufacture. For more information about ENERGY STAR ratings for Lenovo
•
•
•
4744
4748
4743
50 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
By using ENERGY STAR compliant products and taking advantage of the power-
management features of your computer, you reduce the consumption of electricity.
Reduced electrical consumption contributes to potential financial sayings, a cleaner
environment, and the reduction of greenhouse gas emissions.
Lenovo encourages you to make efficient use of energy an integral part of your
day-to-day operations. To help in this endeavor, Lenovo has preset the following
power-management features to take effect when your computer has been inactive
for a specified duration:
ENERGY STAR power-management features, by operating system.
Microsoft Windows XP
Microsoft Windows Vista and
Windows 7
• Turn off monitor: After 15 minutes
• Turn off hard disk drives: Never
• System standby: After 20 minutes
• System hibernates: Never
Power plan: Balanced
• Turn off the display: After 10 minutes
• Put the computer to sleep: After
25 minutes
• Advanced power settings:
– Turn off hard disk drives: After
20 minutes
– Hibernate: Never
To awaken your computer from a Sleep or System Standby mode, press any
key on your keyboard. For more information about these settings, refer to your
Windows Help and Support information system.
User Guide 51
Download from Www.Somanuals.com. All Manuals Search And Download.
52 User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
|
