INSTALLATION AND OPERATION MANUAL
Free-Standing
EPA Certified
Wood-Burning Stoves
Retain These Instructions
For Future Reference
P/N 775,080M, Rev. G, 09/2007
Model CI2000HT Shown
Spectra™ Series Wood Stoves
Models CI1000HT and CI2000HT
A French manual is available upon request. Order P/N 775,080CF.
Ce manuel d’installation est disponible en francais, simplement en faire la demande. Numéro de la
pièce 775,080CF.
Theseappliancesmustbeproperlyinstalledandoperatedinordertopreventthe
possibility of a house fire. Please read this entire installation and operation
manual before installing and using your wood stove. Failure to follow
these instructions could result in property damage, bodily injury or
evendeath.Contactyourlocalbuildingorfireofficialstoobtain
apermitandinformationonanyinstallationrequirements
and inspection requirements in your area.
US
CI1000HT Report #132-S-03-2
CI2000HT Report #132-S-05-2.
WARNINGS
• Hot! Do not touch! The glass and surfaces of this appliance will
be hot during operation and will retain heat for a while after
shutting off the appliance. Severe burns may result.
• Carefully supervise children in the same room as appliance.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONGRATULATIONS!
PACKAGING LIST
When you purchased your new wood stove, you joined the ranks of
thousands of concerned individuals whose answer to their home
heating needs reflects their concern for aesthetics, efficiency and our
environment. We extend our continued support to help you achieve
the maximum benefit and enjoyment available from your new wood
stove.
TheassembledwoodstovemodelsCI1000HTandCI2000HTarepackaged
with an accessory package which contains the following:
One - Installation and Operation Manual
One - Warranty Certificate
One - WoodandBrass,RemovableDoorHandle(foropeningtheashpan
door, firebox door and side door)
One - Air Control / Ash Pan Removal Tool
One - Fire Poker
Four - Leg Cushions
One - Spray Can of Charcoal Paint
It is our goal at Lennox to provide you, our valued customer, with
an appliance that will ensure you years of trouble free warmth and
pleasure.
Thank you for selecting a Lennox stove as the answer to your home
heating needs.
USING THIS MANUAL
Sincerely,
All of us at Lennox Hearth Products
Pleasereadandcarefullyfollowalloftheinstructionsfoundinthismanual.
Please pay special attention to the safety instructions provided in this
manual. Thehomeowner’scareandoperationInstructionsincludedhere
will assure you have many years of dependable and enjoyable service
from your appliance.
TABLE OF CONTENTS
Important Warnings
Page
Page
Page
Page
Page
Page
Page
Page 10
Page 14
Page 18
Page 19
Page 21
Page 22
Page 23
Page 24
Page 31
Page 32
Page 33
Page 34
Page 35
Page 36
2
3
3
3
3
8
9
PRODUCT IS SUBJECT TO CHANGE WITHOUT NOTICE
PLANNING YOUR INSTALLATION
Testing/Listing, EPA
Packaging List
Using this Manual
Planning Your Installation
Clearances - CI1000HT
Clearances - CI2000HT
Installation
Questions To Ask Local Building Official
A correct installation is critical and imperative for reducing fire hazards
and perilous conditions that can arise when wood burning appliances are
improperly installed. The installer must follow all of the manufacturers’
instructions. These models are designed as radiant room heaters and
should be used for no other purpose.
Care and Operation
Recommended Fuel / Wood Storage
Maintenance
Troubleshooting
The installation of a wood burning appliance must conform to local codes
and applicable state and federal requirements and a building permit must
be obtained before installing. Familiarity with these requirements before
installation is essential. Important considerations to discuss with local
building officials include:
Specifications - CI1000HT
Specifications - CI2000HT
Replacement Parts List
Optional Accessories
Safety/Listing Label - CI1000HT
Safety/Listing Label - CI2000HT
EPA Labels
1. Applicable codes (i.e. Uniform Mechanical Code, State or Regional
Codes.)?
2. Local amendments?
Service and Maintenance Log
Product Reference Information
3. Is a permit required - cost?
(Youmaywishtocontactyourinsurancecompanytoaskiftheyrequire
this?).
4. Rooms where the installation is not allowed?
Thisinstallationandoperationmanualwillhelpyouobtainasafe, effi-
cient, dependable installation for your appliance and vent system.
Smoke Detectors
PLEASE READ AND UNDERSTAND THESE INSTRUCTIONS
BEFORE BEGINNING YOUR INSTALLATION
Since there are always several potential sources of fire in any home, we
recommend installing smoke detectors. If possible, install the smoke
detector in a hallway adjacent to the room (to reduce the possibility of
occasional false activation from the heat produced by these appliances).
If your local code requires a smoke detector be installed within the same
room, you must follow the requirements of your local code. Check with
your local building department for requirements in your area.
TESTING / LISTING
Models CI1000HT and CI2000HT have been Listed to UL Standard #1482
and ULC-S627 by OMNI-Test Laboratories, Inc.; Beaverton, OR; Report
numbers; CI1000HT #132-S-03-2 and CI2000HT #132-S-05-2.
Installation / Solid Fuel Standards
National Fire Protection Association – The primary NFPA standard that
refers to installation and maintenance of wood fired appliances and
venting is NFPA 211 – Latest Edition: Chimneys, Fireplaces, Vents, and
Solid Fuel appliances.
EPA (Environmental Protection Agency)
This heater meets EPA particulate matter (smoke) control requirements
for noncatalytic wood heaters built on or after July 1, 1990.
Note – This appliance is NOT approved for installation into a Manu-
factured Home.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SELECTING A LOCATION
CAUTION
The design of your home and where you place your stove will determine
its value as a source of heat. This type of appliance depends primarily on
air circulation (convection) to disperse its heat, and therefore, a central
locationisoftenbest.Thereareotherpracticalconsiderations,whichmust
be considered before a final selection of locations is made.
The body of these appliances are very heavy. The
use of a heavy duty escalara (stair step hand truck)
is recommended for lifting the appliance body.
Floor Protection - Model CI1000HT
(USA ONLY)
• Existing Chimneys
The floor protector must meet or exceed the minimum thermal require-
ments as defined here (see Floor Protection / Hearth Extension Using
Alternate Material As Floor Protector). If the floor protection is to be
stone, tile, brick, etc., it must be mortared or grouted to form a continu-
ousnoncombustiblesurface. Ifachimneyconnectorextendshorizontally
over the floor, protection must also cover the floor under the connector
and at least 2” (51 mm) to either side.
• Wood Storage
• Aesthetic Considerations
• Roof Design (rafter locations & roof pitch)
• Room Traffic
The floor protector must fully cover the area beneath the appliance and
extend 18” to the front, 5.2” to the sides, and 0” from the back as shown
in Figure 1.
• Proximity to Combustibles
The installation of these appliances will require some research. Once your
options are determined, consult with your local building department who
will be able to give you the necessary installation requirements for your
area (Is a building permit required? Rooms where installation may not
be allowed, etc.).
For Floor Protection Material Requirements:
In USA see Page 5
In Canada see Page 6
USA - 5.2” (132 mm)
Canada - 8” (203 mm)
Minimum
WARNING
Check all local building and safety codes before
installation.Theinstallationinstructionsandappro-
priate code requirements must be followed exactly
andwithoutcompromise.Alterationstothestoveare
not allowed. Do not connect the stove to a chimney
system serving another stove, appliance, or any air
distributionduct.Failuretofollowtheseinstructions
will void the manufacturers warranty.
USA - 0 “ (0 mm)
Floor
Canada - 8” (203 mm)
Protector
Minimum
Stove Back
Stove Front
If you plan to vent your stove into an existing masonry chimney, have it
inspected by a local fire marshal or qualified installer. Remember that a
stove’s performance is heavily influenced by the chimney and its location
on the roof. An oversized flue may not provide effective draw, and a flue
liner may be required (see Draft Requirements on Page 11). Consult your
dealer or qualified installer before final selection is made.
USA - 5.2” (132 mm)
Canada - 18” (457 mm)
Minimum
Top View
Thisstoverequirespre-installationworktobecompletedbeforeinstallation
can take place. This may include modification for flue and chimney.
USA - 5.2” (132 mm)
Canada - 8” (203 mm)
Minimum
The appliance should be inspected before use and the chimney cleaned
at least annually. More frequent cleaning may be required due to poor
operation, installation, or low quality fuel.
Figure 1 - Floor Protection Requirements, Model CI1000HT
4
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the r formula:
Minimum
Floor Protection / Hearth Extension Using Alternate Material As
Floor Protector - Model CI1000HT (USA only)
r-value (per Inch)
of listed material
r-value (per inch)
of alternate material
Specified min.
thickness
of listed
thickness of
alternate
material
=
x
Note: Also see Floor Protection above .
material
The hearth pad or alternate material used as a floor/hearth protector must
be constructed of a durable noncombustible material having an equal or
better thermal conductivity value (lower k value) of k =.84 BTU/IN FT2
HR °F or a thermal resistance that equals or exceeds r = 1.19 HR °F FT2
IN/BTU with a minimum thickness of 1/2”. With these values, determine
the minimum thickness of the alternate material required using the
formula(s) and shown in Table 1.
rL
rM
TM (inches)
=
=
x
x
x
TL
TM (inches)
*1.19
* .52
.5"
.5"
1.144 (inches)=
2.288
Answer -TheminimumrequiredthicknessoftheDurockis1.143"therefore
round up to nearest standard thickness available which is 1-1/4."
Note: Any noncombustible material having a minimum thickness of 1/2”
(13 mm) whose k value is less than .84 or whose r value is more than
1.19 is acceptable. If the alternate material used has a higher k value
or lower r value will require a greater thickness of the material used. In
some cases, if the k value is less or the r value higher, a thinner material
may be used.
Listed Material
k (per inch) r (per inch)
Listed Min. Thickness
Listed Material
.84
1.19
rL
1/2" (.5")
KL
TL
** Approved Alternate Materials for Floor/Hearth Protection
Methods of determining floor protection equivalents:
To determine the thickness required for the alternate material when
either the "k" value or "r" value is known, use either the k formula or r
formula.
Alternative Materials
Thermal Values
Minimum Thickness
(rounded to nearest 1/8 inch)
k (per inch) r (per inch)
Min. Thickness
KM
rM
TM
Kaowool M Board
.47
.35
2.13
2.86
.28" (1/4")
.21" (1/4")
Example: If Durock™ Cement Board is to be used for the floor protection,
how thick must this material be?
Micore 160™
U.S. Gypsum
Micore 300™
.46
2.17
.52
.27" (1/4")
kM = k value per inch of alternate material
rM = r value per inch of alternate material
TM = minimum thickness required for alternate material
TS = standard thickness of the alternate material
U.S. Gypsum
Durock™ Cement Board
U.S. Gypsum
1.92
1.14" (1-1/8")
Hardibacker™
1.95
2.30
2.82
.51
.43
.35
1.16" (1-1/8")
1.37" (1-3/8")
1.68" (1-5/8")
Hardibacker 500™
kL = k value per inch of listed material
rL = r value per inch of listed material
TL = minimum thickness of listed material
Cultured Stone Hearth-
stone™
Wonderboard
3.23
.61
.31
1.92" (1-7/8")
.36" (3/8")
Note: An asterisk "*" indicates, it is a value taken from Table 1.
Using the k formula:
Super Firetemp M
Johns-Manville
1.64
Super Firetemp L
Johns-Manville
.54
1.85
.32" (3/8")
Minimum
k-value (per Inch) of
alternate material (kM) x
k-value (per inch)
Specified min.
thickness
Face brick
9.00
5.00
5.00
12.5
~11
.111
.20
5.36" (5-3/8")
2.98" (3")
thickness of
alternate
=
Common brick
Cement mortar
Ceramic tile
Marble
of listed
material (TM)
of listed material (kL)
material (TL)
.20
2.98" (3")
TM (inches)
TM (inches)
=
=
kM
x
x
x
TL
.08
7.44" (7-1/2")
6.55" (6-1/2")
*.84
~.09
*1.92
*.84
.5"
.5"
Table 1
1.143 (inches)=
2.286
** If the hearth extension material(s) that is intended to be used is NOT listed
on Table 1, the material can still be used if the material(s) is noncombustible.
However,themanufacturerofthematerialmustprovideeitherthelistedk-value
per inch or r-value per inch with listed thickness so that the minimum thickness
required for the hearth can be calculated (per instructions on this Page and/or
as specified in the NFI Certification Manuals).
Answer -TheminimumrequiredthicknessoftheDurockis1.143"therefore
round up to nearest standard thickness available which is 1-1/4."
Note: Also see NFI (National Fireplace Institute) Certification Manuals show-
ing other acceptable calculation methods and acceptable alternate materials
which can be used.
5
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the r formula:
Minimum
Floor Protection / Hearth Extension Using Alternate Material As
Floor Protector - Model CI1000HT (Canada only)
r-value (per Inch)
of listed material
r-value (per inch)
of alternate material
Specified min.
thickness
of listed
thickness of
alternate
material
=
x
Note: Also see Floor Protection above .
material
The hearth pad or alternate material used as a floor/hearth protector must
be constructed of a durable noncombustible material having an equal or
better thermal conductivity value (lower k value) of k =.84 BTU/IN FT2
HR °F or a thermal resistance that equals or exceeds r = 1.19 HR °F FT2
IN/BTU with a minimum thickness of 1/2”. With these values, determine
the minimum thickness of the alternate material required using the
formula(s) and shown in Table 2.
rL
rM
TM (inches)
=
=
x
x
x
TL
TM (inches)
*1.19
* .52
1.45"
1.45"
1.144 (inches)=
2.288
Answer - The minimum required thickness of the Durock is 3.31" therefore
round up to nearest standard thickness available which is 3-5/16."
Note: Any noncombustible material having a minimum thickness of 1/2”
(13 mm) whose k value is less than .84 or whose r value is more than
1.19 is acceptable. If the alternate material used has a higher k value
or lower r value will require a greater thickness of the material used. In
some cases, if the k value is less or the r value higher, a thinner material
may be used.
Listed Material
k (per inch) r (per inch)
Listed Min. Thickness
Listed Material
.84
1.19
rL
1.45" (1-1/2")
KL
TL
** Approved Alternate Materials for Floor/Hearth Protection
Methods of determining floor protection equivalents:
To determine the thickness required for the alternate material when
either the "k" value or "r" value is known, use either the k formula or r
formula.
Alternative Materials
Thermal Values
Minimum Thickness
(rounded to nearest 1/8 inch)
k (per inch) r (per inch)
Min. Thickness
KM
rM
TM
Kaowool M Board
.47
.35
2.13
2.86
.81" (3/4")
.60" (5/8")
Example: If Durock™ Cement Board is to be used for the floor protection,
how thick must this material be?
Micore 160™
U.S. Gypsum
Micore 300™
.46
2.17
.52
.79" (3/4")
kM = k value per inch of alternate material
rM = r value per inch of alternate material
TM = minimum thickness required for alternate material
TS = standard thickness of the alternate material
U.S. Gypsum
Durock™ Cement Board
U.S. Gypsum
1.92
3.31" (3-3/8")
Hardibacker™
1.95
2.30
2.82
.51
.43
.35
3.37" (3-3/8")
3.97" (4")
Hardibacker 500™
kL = k value per inch of listed material
rL = r value per inch of listed material
TL = minimum thickness of listed material
Cultured Stone Hearth-
stone™
4.87" (4-7/8")
Wonderboard
3.23
.61
.31
5.58" (5-5/8")
1.05" (1")
Note: An asterisk "*" indicates, it is a value taken from Table 2.
Using the k formula:
Super Firetemp M
Johns-Manville
1.64
Super Firetemp L
Johns-Manville
.54
1.85
.93" (7/8")
Minimum
k-value (per Inch) of
alternate material (kM) x
k-value (per inch)
Specified min.
thickness
Face brick
9.00
5.00
5.00
12.5
~11
.11
.20
15.54" (15-1/2")
8.63" (8-5/8")
8.63" (8-5/8")
21.58" (21-5/8")
18.99" (19")
thickness of
alternate
=
Common brick
Cement mortar
Ceramic tile
Marble
of listed
material (TM)
of listed material (kL)
material (TL)
.20
TM (inches)
TM (inches)
=
=
kM
x
x
x
TL
.08
*.84
~.09
*1.92
*.84
1.45"
1.45"
Table 2
1.143 (inches)=
2.286
** If the hearth extension material(s) that is intended to be used is NOT listed
on Table 2, the material can still be used if the material(s) is noncombustible.
However,themanufacturerofthematerialmustprovideeitherthelistedk-value
per inch or r-value per inch with listed thickness so that the minimum thickness
required for the hearth can be calculated (per instructions on this Page and/or
as specified in the NFI Certification Manuals).
Answer -TheminimumrequiredthicknessoftheDurockis3.31"therefore
round up to nearest standard thickness available which is 3-5/16."
Note: Also see NFI (National Fireplace Institute) Certification Manuals show-
ing other acceptable calculation methods and acceptable alternate materials
which can be used.
6
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
Floor Protection - Model CI2000HT (USA and Canada)
Methods of determining floor protection equivalents:
To determine the thickness required for the alternate material when
either the "k" value or "r" value is known, use either the k formula or r
formula.
The floor protector must meet or exceed the minimum thermal require-
ments as defined on this Page (see Floor Protection / Hearth Extension
Using Alternate Material As Floor Protector). If the floor protection is
to be stone, tile, brick, etc., it must be mortared or grouted to form a
continuous noncombustible surface. If a chimney connector extends
horizontally over the floor, protection must also cover the floor under
the connector and at least 2” (51 mm) to either side.
Example: If Durock™ Cement Board is to be used for the floor protection,
how thick must this material be?
kM = k value per inch of alternate material
rM = r value per inch of alternate material
TM = minimum thickness required for alternate material
TS = standard thickness of the alternate material
The floor protector must fully cover the area beneath the appliance and
extend 18” to the front, 5”-USA and 8”-Canada to the sides, and 0”-USA
and 8”-Canada from the back as shown in Figure 2.
kL = k value per inch of listed material
rL = r value per inch of listed material
TL = minimum thickness of listed material
Note: For Floor Protection Material Requirements in USA and Canada
see Floor Protection Using Alternate Material As Floor Protector on
this page.
Note: An asterisk "*" indicates, it is a value taken from Table 3.
Using the k formula:
Floor
Protector
USA - 0 “ (0 mm)
Canada - 8” (203 mm)
Minimum
Minimum
thickness of
alternate
k-value (per Inch) of
alternate material (kM) x
k-value (per inch)
Specified min.
thickness
=
Stove Back
of listed
material (TM)
of listed material (kL)
material (TL)
TM (inches)
TM (inches)
=
=
k
M
x
x
x
TL
Stove Front
*.84
*1.92
*.84
.5"
.5"
USA - 18” (457 mm)
Canada - 18” (457 mm)
Minimum
1.143 (inches)=
2.286
Answer -TheminimumrequiredthicknessoftheDurockis1.143"therefore
round up to nearest standard thickness available which is 1-1/4."
USA - 5” (127 mm)
Canada - 8” (203 mm)
Minimum
USA - 5” (127 mm)
Canada - 8” (203 mm)
Minimum
Using the r formula:
Minimum
thickness of
alternate
material
r-value (per Inch)
of listed material
r-value (per inch)
of alternate material
Specified min.
thickness
of listed
Top View
=
x
Figure 2- Floor Protection Size Requirements, Model CI2000HT
material
rL
rM
TM (inches)
=
=
x
x
x
TL
Floor Protection / Hearth Extension Using Alternate Material As
Floor Protector - Model CI2000HT (USA and Canada)
TM (inches)
*1.19
* .52
.5"
.5"
Note: Also see Floor Protection above .
1.144 (inches)=
2.288
Answer -TheminimumrequiredthicknessoftheDurockis1.143"therefore
round up to nearest standard thickness available which is 1-1/4."
The hearth pad or alternate material used as a floor/hearth protector must
be constructed of a durable noncombustible material having an equal or
better thermal conductivity value (lower k value) of k =.84 BTU/IN FT2
HR °F or a thermal resistance that equals or exceeds r = 1.19 HR °F FT2
IN/BTU with a minimum thickness of 1/2”. With these values, determine
the minimum thickness of the alternate material required using the
formula(s) and shown in Table 3.
Note: Any noncombustible material having a minimum thickness of 1/2”
(13 mm) whose k value is less than .84 or whose r value is more than
1.19 is acceptable. If the alternate material used has a higher k value
or lower r value will require a greater thickness of the material used. In
some cases, if the k value is less or the r value higher, a thinner material
may be used.
7
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
Floor Protection - Model CI2000HT (USA and Canada)
Continued...
CLEARANCES - MODEL CI1000HT
Listed Material
COMBUSTIBLE WALL CLEARANCE – USA & Canada
k (per inch) r (per inch)
Listed Min. Thickness
WARNING: It is very important that you observe the minimum
clearances.
Listed Material
.84
1.19
rL
1/2" (.5")
KL
TL
** Approved Alternate Materials for Floor/Hearth Protection
There are listed clearances for your stove which were determined in a
Laboratory test using various “classes” of stove pipe or chimney. Mini-
mums are first established for the stove itself and increased based on
how much heat is transferred by each class of pipe.
Alternative Materials
Thermal Values
Minimum Thickness
(rounded to nearest 1/8 inch)
k (per inch) r (per inch)
Min. Thickness
KM
rM
TM
Kaowool M Board
.47
.35
2.13
2.86
.28" (1/4")
.21" (1/4")
Position the unit no closer than the minimum clearances to combustible
materials. Check that no overhead cross members in the ceiling or roof
will be cut. Reposition unit if necessary being careful not to move closer
than the minimum clearances.
Micore 160™
U.S. Gypsum
Micore 300™
U.S. Gypsum
.46
2.17
.52
.27" (1/4")
Durock™ Cement Board
U.S. Gypsum
1.92
1.14" (1-1/8")
Minimum Ceiling Height – 7 feet / 2133mm from floor to ceiling.
Hardibacker™
1.95
2.30
2.82
.51
.43
.35
1.16" (1-1/8")
1.37" (1-3/8")
1.68" (1-5/8")
Single Wall Pipe Without Pipe Shield - CI1000HT
Hardibacker 500™
Using single wall 24 MSG black or 25 MSG blued steel connector pipe
with factory-built chimney listed to either UL 103HT or ULC S629.
Cultured Stone Hearth-
stone™
Wonderboard
3.23
.61
.31
1.92" (1-7/8")
.36" (3/8")
Super Firetemp M
Johns-Manville
1.64
Minimum Clearances to Combustibles - inches (millimeters)
Super Firetemp L
.54
1.85
.32" (3/8")
A
B
C
G
27-1/2” (699 mm)
27” (686 mm)
27” (686 mm)
D
E
F
24” (610 mm)
18” (457 mm)
19” (483 mm)
Johns-Manville
Face brick
9.00
5.00
5.00
12.5
~11
.111
.20
5.36" (5-3/8")
2.98" (3")
Common brick
Cement mortar
Ceramic tile
Marble
.20
2.98" (3")
35-3/16” (894 mm) This is a reference dimension only
.08
7.44" (7-1/2")
6.55" (6-1/2")
Table 4 - Model CI1000HT (see Figures 3 and 4)
~.09
Table 3
Single Wall Pipe With Pipe Shield / Reduced Clearance -
CI1000HT
** If the hearth extension material(s) that is intended to be used is
NOT listed on Table 3, the material can still be used if the material(s)
is noncombustible. However, the manufacturer of the material must
provide either the listed k-value per inch or r-value per inch with listed
thickness so that the minimum thickness required for the hearth can
be calculated (per instructions on this Page and/or as specified in the
NFI Certification Manuals).
Using single wall 24 MSG black or 25 MSG blued steel connector pipe
with factory-built chimney listed to either UL 103HT or ULC S629. The
use of a pipe shield for 6” connector with 1” clearance to the pipe is
mandatory.
Minimum Clearances to Combustibles - inches (millimeters)
Note: Also see NFI (National Fireplace Institute) Certification Manuals
showingotheracceptablecalculationmethodsandacceptablealternate
materials which can be used.
A
B
C
G
21-1/2” (546 mm)
27” (686 mm)
19” (483 mm)
D
E
F
18” (457 mm)
18” (457 mm)
11” (279 mm)
23-7/8” (606 mm) This is a reference dimension only
Table 5 - Model CI1000HT (see Figures 3 and 4)
Protected Wall Clearance - CI1000HT and CI2000HT
Some local codes will allow reduced clearances when the stove is
installed adjacent to a protected wall system. The variance must be
approved by your local building official. Normally, the protected wall
system is defined as a non- combustible material with a minimum of
1” air space behind. Check your local building codes or with a qualified
installer (Ref. NFPA 211).
8
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEARANCES - MODEL CI2000HT
Combustible
D
COMBUSTIBLE WALL CLEARANCE – USA & Canada
WARNING: It is very important that you observe the minimum
clearances.
A
E
There are listed clearances for your stove which were determined in a
Laboratory test using various “classes” of stove pipe or chimney. Mini-
mums are first established for the stove itself and increased based on
how much heat is transferred by each class of pipe.
B
Position the unit no closer than the minimum clearances to combustible
materials. Check that no overhead cross members in the ceiling or roof
will be cut. Reposition unit if necessary being careful not to move closer
than the minimum clearances.
Figure 3 - Parallel Installation
Single Wall Pipe - CI2000HT
(Not approved for alcove installations)
Combustible
Using single wall 24 MSG black or 25 MSG blued steel connector pipe
with factory-built chimney listed to either UL 103HT or ULC S629.
F
Minimum Clearances to Combustibles - inches (millimeters)
C
A
B
C
G
18” (457 mm)
32” (813 mm)
27” (686 mm)
D
E
F
13” (330 mm)
20” (508 mm)
16” (406 mm)
G
35-3/16” (894 mm) This is a reference dimension only
Table 6 (see Figures 3 and 4)
B
Double Wall Pipe - CI2000HT
(For alcove installations, clearances “C” and “F” are not applicable) Use
listed double wall chimney connector or Type L vent pipe to the top of
the stove.
Minimum Clearances to Combustibles - inches (millimeters)
Figure 4 - Corner Installation
A
B
C
14-1/2” (368 mm)
28-1/2” (724 mm)
18” (457 mm)
D
E
F
10” (254 mm)
17” (432 mm)
7” (178 mm)
MODEL CI1000HT IS NOT APPROVED FOR USE WITH DOUBLE
WALL PIPE.
Table 7 (see Figures 3 and 4)
DO NOT INSTALL THE CI1000HT INTO AN ALCOVE OR A CONFINED
SPACE. This unit has not been tested or approved for installation
into a confined space such as an alcove (see the national standard
below).
Minimum Ceiling Height for Single wall pipe and double wall pipe instal-
lations and Alcove Installations – 60” (1524 mm) from floor to ceiling
and 29” (737 mm) from stove top to ceiling.
NFPA 211- latest edition: (Applies to Solid Fuel Burning Appliances,
which are not alcove tested) - Solid fuel-burning appliances shall
not be installed in confined spaces. The space or room shall be of
ample size to allow adequate circulation of heated air. Appliances
shall be so located as not to interfere with the proper circulation
of air within the heated space.
Alcove Installation Clearances - CI2000HT
Alcove Installations Require Double Wall Pipe Only
Use listed double wall chimney connector or Type L vent pipe to the top
of the stove.
Minimum Clearances to Combustibles - inches (millimeters)
Installing Leg Pads
A
B
C
14-1/2” (368 mm)
28-1/2” (724 mm)
N/A
D
E
F
10” (254 mm)
17” (432 mm)
N/A
The four leg pads (included in accessory package), are provided for
placement under the four legs.
Table 8 (see Figures 3 and 4)
Note: Alcove clearances cannot be reduced using wall protection. Maxi-
mum alcove depth must be no more than 48” (1220 mm).
9
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
Minimum / Maximum Flue Diameter:
Minimum 6”, Maximum 10”
INSTALLATION
Chimney Connector Adapter
Types of Chimneys
Use a chimney connector adapter to connect the chimney connector up
to the chimney. The small ends of the chimney connector should all point
down for a drip free installation. Position all seams toward the back for
aesthetics. The chimney connector must be 6-inch diameter.
The unit must be connected to either a code-approved masonry chimney
withaflueliner, ora6inchdiameterfactory-builtchimneycomplyingwith
the requirements for Type HT chimneys in the standard UL 103.
The chimney is a vital part of your stove installation. A properly built
masonrychimneyoraproperlyinstalledfactory-builtchimneywillassure
a consistent draft under a variety of weather conditions (a smoking
stove is usually caused by a chimney problem). The stove flue size is
6 inches diameter, which is approximately 28 square inches minimum.
The maximum flue size should be no more than three (3) times the cross
sectional area of the size of the stove flue collar. In this case, that would
be no larger than an 10-inch diameter stack, or approximately 85 square
inches maximum.
Secure adjoining sections of chimney connector to each other using three
equally spaced sheet metal screws. Secure the connector pipe to flue
collar using three equally spaced sheet metal screws. DO NOT secure
chimney connector to chimney with screws.
Connection To A Factory-built Chimney
Thisspaceheateristobeconnectedtoafactory-builtchimneyconforming
toCAN / ULC – S629, Standard for650°C Factory-BuiltChimneys. Allpipe
connections must be sealed (ie. high temperature silicone).
All chimneys must be installed as specified by local building codes and
according to the chimney manufacturer instructions (in the case of
a factory-built chimney). See the chimney manufacturer instructions
for exact specifications. Factory-built chimneys must comply with UL
103HT or ULC S629. A chimney connector shall not pass through an attic
or roof space, closet or similar concealed space, or a floor, or ceiling.
Where passage through a wall, or partition of combustible construction
is desired, the installation shall conform to CAN/CSA-B365, Installation
Code for Solid-Fuel-Burning Appliances and Equipment.
ForReducedResidentialClearancesUsingDoubleWallPipe(Approved
for Model CI2000HT Only):
Type L and listed double wall connector pipe is acceptable. Install any fac-
tory-built brand of pipe according to the manufacturer’s instructions.
Vapor Barrier at Chimney Penetration
Install all venting components per the Vent Manufacturers installation
instructions. Ensure that there is an effective vapor barrier at the location
where the chimney penetrates to the exterior of the structure. This can
be accomplished by applying a non-hardening waterproof sealant to the
following components:
Tile-lined Masonry Chimney
• Around the chimney at the point where the storm collar will meet the
chimney just above the Flashing
• Along the vertical seam of the chimney pipe, where it is exposed to
the weather.
Factory
Built
Chimney
• On each nail head on the flashing.
• Around the chimney at the point where the storm collar will meet the
chimney just above the flashing.
Figure 5 - Types of Chimney
Notes:
Acceptable Connector Pipe For Installations
• On a flat or tarred and graveled roofs, nail and seal the flat roof flashing
to the roof on all sides with roofing compound.
• Do not put screws through the flashing into the chimney pipe.
When Using Single Wall Pipe: Install a six (6) inch diameter, single wall,
24 MSG black steel or 26 MSG blued steel connector pipe on the flue
collar of the unit. When installing pipe, the crimped ends of the pipe
should all point down. Position all seams toward the back for aesthet-
ics. Three (3) pre-drilled holes are provided in the flue collar for fasten-
ing the pipe securely to the stove. Use sheet metal screws to do this.
Additional sections of single wall pipe should be fastened together with
at least three (3) sheet metal screws each section. All pipe connections
must be sealed (ie. high temperature silicone). When connecting to the
factory-built ceiling support package, use the manufacturer’s transition
piece, usually called a dripless connector, to join single wall pipe to their
factory-built chimney section.
Chimney Inspection
Existing chimneys must be inspected before installing your stove. Con-
sult your local building department for chimney code requirements. A
masonry chimney must have a code approved liner. This liner must not
have broken or missing pieces. Some non-code masonry chimneys may
be brought up to code by being relined. (Consult your dealer or qualified
chimney sweep). Factory-built chimneys should also be inspected, first
for creosote deposits (which should be removed), and then for integrity
of the stainless steel liner. Look for obvious bulges in the lining, which
may indicate the need to replace that section (use a bright flashlight).
Also, inspect the attic to see that the chimney has proper clearance to
combustible framing members. For interior masonry chimneys and most
factory-built chimneys, this must be a two (2) inch air space clearance,
which must not be filled with insulation or any other material. An exterior
masonry chimney must have a one (1) inch air space clearance.
WhenUsingApprovedDoubleWallPipe(ApprovedforModelCI2000HT
Only)
Type L and listed double wall connector pipe is acceptable. Install any
factory-built brand of pipe according to the manufacturer’s instructions.
All pipe connections must be sealed (ie. high temperature silicone).
10
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
Chimney Height Requirements
CAUTION
The chimney must extend 3 feet above the level of roof penetration and a
minimum of 2 feet higher than any roof surface within 10 feet (see below).
Check with your local building officials for any additional requirements
for your area.
Manystructurefireshaveresultedwhenaslowburning
fire has been left unattended for any extended period
of time. These fires normally occur becausecombus-
tible materials close to an appliance become heated
to the ignition point by an overfired appliance which
the operator thought was safety “throttled down.”
Due to prevailing winds, local terrain, adjacent tall trees, a hill, or ravine
near the home, or adjacent structures, additional chimney height or a
special chimney cap may be required to ensure optimum performance.
See Figure 6 for the 10’ by 2’ Rule for Vent Termination. The top of the
flue must be 2’ (610 mm) higher than any part of the roof within 10’ (305
cm) horizontal and a minimum of 3’ (915 mm) higher than the highest
point of roof penetration.
Draft Requirements
The appliance is merely one component of a larger system. The other
equally important component is the venting system which is necessary
for achieving the required flow of combustion air to the fire chamber and
for safely removing unwanted combustion by-products from the appli-
ance. If the venting system’s design does not promote these ends, the
system may not function properly. Poorly functioning venting systems
may create performance problems (i.e. smoking stove, poor heat output,
fire goes out, window blackens, increased creosote buildup, etc.) as
well as be a safety hazard. Some factors that may lead to performance
problems are as follows:
Important Note:
The installation of a barometric damper is recommended for all free-
standing stoves in areas that may have high winds, which can effect the
draft. The installation must be only in units with a newly constructed
chimney, free of creosote deposits. The barometric damper is an auto-
matic device designed to regulate the draft in a heating appliance, which
in turn, stabilizes the chimney temperatures, lessening the potential of
over-firing. Do not place the barometric damper greater than 24 inches
(610 mm) above the unit. Excessive draft will lead to poor control of
the burning rate and possible over-firing of the stove and damage to the
cast iron firebox. Most barometric dampers are calibrated in inches of
water column and can be set to draft requirements of -.03 to -.08 inches
(-7.5 to -20 Pa). It is recommended that the barometric dampers to be
set between -.05 and -.06 inches.
• Oversized or undersized chimney.
• Excessive offsets in venting.
• Insufficient vertical height of chimney.
• Insufficient chimney termination height in relationship to roof.
• Insufficient ventilation.
• Lack of maintenance.
• Improper operation.
• Burning improper fuel (unit is approved for use with natural dry well-
seasoned wood only).
• Down drafts in the chimney (may need a special wind cap).
Less than
10' (3 m)
2’ (610 mm) Min.
To ensure that the venting system is functioning properly a draft test
should be performed (see Draft Test Procedure on this page).
3' (914 mm)
3'
Min.
10'
(3 m)
(914 mm)
American National Standards Institute ANSI/NFPA 211-96: A chimney or
vent shall be so designed and constructed to develop a flow sufficient
to completely remove all flue and vent gases to the outside atmosphere.
The venting system shall satisfy the draft requirements of the connected
appliance in accordance with the manufacturer instructions.
Min.
Figure 6 - The 10’ by 2’ Rule for Vent Termination
Draft Test Procedure
After this appliance is installed a draft test should be performed to
ensure proper draft. A qualified technician should perform the draft test
procedure as follows:
THERECOMMENDEDDRAFTREQUIREMENTSFORTHESEAPPLIANCES
IS NO LESS THAN -.05 AND NO GREATER THAN -.06. OPERATION OF
YOURSTOVEWITHADRAFTGREATERTHAN-.06CANPOSSIBLYCAUSE
DAMAGE TO THE STOVE AND VOID THE WARRANTY.
1) Close all windows and doors in the dwelling.
2) Turn on or operate all appliances which remove air from the home
(such as a furnace, heat pump, air conditioner, clothes dryer, exhaust
fans, fireplaces, and other fuel burning appliances).
Fireintensityisafunctionofseveralfactors. OneofthesefactorsisDRAFT.
Normally, increasing draft increases fire intensity. Conversely, increasing
the fire intensity will increase draft. Draft can also be affected by external
factors such as wind strength and direction, outside temperature, airflow
in or out of the structure, and so forth. If one of these factors changes,
the draft of a low-burning appliance may increase. This increased draft
may cause dangerously high temperature to develop, possibly causing
failure of the unit or flue, or ignition of nearby combustibles. Closing
down the combustion airflow (“Primary Air Draft Control”) may not
guarantee that this will not happen.
11
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Drill a hole in the vent pipe per the draft gauge manufacturers instruc-
tions (to create a draft test port). Note: Hole location should be a
minimum of 1 foot above flue outlet collar.
Single Wall Pipe
Using 6” Diameter Single Wall Connector Pipe
4) Start a fire (See How To Start And Maintain A Fire on Page 15).
Chimney
Termination
Cap
5) After the fire is well established (20-25 minutes) and burning at a low
setting,performthedrafttestperthegaugemanufacturerinstructions.
The draft gauge should read between .05 and .06” W.C. (inches water
column). Excessive draft (above .06 W.C.I.) can result in too much
combustion air to be pulled into the firebox, this will produce hotter
burns and could result in overfiring. Too little draft (below .05” W.C.)
will not allow enough combustion air delivery to maintain a fire well
or cause performance problems such as smoking (this may result in
improper operation of appliance, i.e. will not maintain fire well unless
fuel door is left open).
Storm
Collar
Roof
Flashing
CeilingSupport
Assembly
6) Install a screw to seal the draft test port in the vent pipe. If the draft
test reading was not within the required range, correct the installation
and repeat this procedure.
Slip
Adapter
Ventilation Requirements / Provide Adequate Air For Combustion
THE FRESH AIR REQUIREMENTS OF THIS APPLIANCE MUST BE MET
WITHIN THE SPACE WHERE IT WILL BE INSTALLED. VENTILATION IS
ESSENTIAL WHEN USING A SOLID FUEL BURNING HEATER.
In well insulated and weather tight homes, it may be difficult to establish
a good draft up the chimney (caused by a shortage of air in the home).
The lack of air is caused by many common household appliances which
exhaust air from the home (such as a furnace, heat pump, air conditioner,
clothesdryer,exhaustfans,fireplaces,andotherfuelburningappliances).
Also, the combustion process of this heater uses oxygen from inside the
dwelling. If the available fresh air delivery in the dwelling is insufficient
to support the demands of these appliances, problems can result (i.e.
excessive negative pressure can develop in the dwelling which will affect
the rate at which this appliance can draft thus resulting in performance
problems; See Draft Requirements on Page 11). To correct this problem
it may help to open a window (preferably on the windward side of the
house) or install a vent to provide make-up air into the dwelling.
Chimney
Connector
6” x 24” 24-gage
black steel or 26 gage
blued steel single
wall pipe
Important Notes:
• Minimize the use of elbows (30°, 45° or 90°) - Offsets in the venting
system are very restrictive and will inhibit the draft (i.e. You will lose
approximately 5 feet of effective draft for every 90 degrees of direction
change). This appliance requires 12 to 15 feet of effective draft for
optimum performance (see Draft Requirements on Page 11).
• First section of pipe must be vertical - Use as much straight vertical
pipe directly above the appliance as possible before using an elbow
(a 2’ to 3’ initial vertical rise is suggested).
• See pipe manufacturers instructions for installation requirements of
venting components and vent clearances.
Figure 7 - Single Wall Pipe
12
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
Combustible Wall Chimney Connector Pass-Throughs
Refer to Figure 9
Double Wall Pipe
(Approved for Model CI2000HT Only)
Using 6” Diameter Type L-Vent Connector Pipe
Method A. 12” (305 mm) Clearance to Combustible Wall Member:
Using a minimum thickness 3.5” (89 mm) brick and a 5/8” (16 mm)
minimum wall thickness clay liner, construct a wall pass-through. The
clay liner must conform to ASTM C315 (Standard Specification for Clay
Fire Linings) or its equivalent. Keep a minimum of 12” (305 mm) of brick
masonry between the clay liner and wall combustibles. The clay liner
shall run from the brick masonry outer surface to the inner surface of
the chimney flue liner but not past the inner surface. Firmly grout or
cement the clay liner in place to the chimney flue liner.
Termination Cap with
SparkArrestor
Storm
Collar
3Feet
Minimum
Flashing
MethodB.9”(229mm)ClearancetoCombustibleWallMember:Using
a 6” (153 mm) inside diameter, listed, factory-built Solid-Pak chimney
section with insulation of 1” (26 mm) or more, build a wall pass-through
with a minimum 9” (229 mm) air space between the outer wall of the
chimney length and wall combustibles. Use sheet metal supports
fastened securely to wall surfaces on all sides, to maintain the 9” (229
mm) air space. When fastening supports to chimney length, do not
penetrate the chimney liner (the inside wall of the Solid-Pak chimney).
The inner end of the Solid-Pak chimney section shall be flush with the
inside of the masonry chimney flue, and sealed with a non-water soluble
refractory cement. Use this cement to also seal to the brick masonry
penetration.
Support
Box
Method C. 6” (153 mm) Clearance to Combustible Wall Member:
Starting with a minimum 24 gage (.024” [.61 mm]) 6” (153 mm) metal
chimneyconnector,andaminimum24gageventilatedwallthimblewhich
has two air channels of 1” (26 mm) each, construct a wall pass-through.
There shall be a minimum 6” (153 mm) separation area containing
fiberglass insulation, from the outer surface of the wall thimble to wall
combustibles. Support the wall thimble, and cover its opening with a
24-gageminimumsheetmetalsupport.Maintainthe6”(153mm)space.
There should also be a support sized to fit and hold the metal chimney
connector. See that the supports are fastened securely to wall surfaces
on all sides. Make sure fasteners used to secure the metal chimney
connector do not penetrate chimney flue liner.
Minimumof
12-15’ofFlueto
achieveastable
draft.
DVL Close Clearance
Connector Pipe
7Feet
Minimum
Method D. 2” (51 mm) Clearance to Combustible Wall Member: Start
withasolid-paklistedfactorybuiltchimneysectionatleast12”(304mm)
long, with insulation of 1” (26 mm) or more, and an inside diameter of
8” (2 inches [51 mm] larger than the 6” [153 mm] chimney connector).
Use this as a pass-through for a minimum 24-gage single wall steel
chimney connector. Keep solid-pak section concentric with and spaced
1” (26 mm) off the chimney connector by way of sheet metal support
plates at both ends of chimney section. Cover opening with and sup-
port chimney section on both sides with 24 gage minimum sheet metal
supports. See that the supports are fastened securely to wall surfaces
on all sides. Make sure fasteners used to secure chimney section do
not penetrate chimney flue liner.
Floor
Protector
Figure 8 - Double Wall Pipe
1. Connectors to a masonry chimney, excepting method B, shall extend
in one continuous section through the wall pass-through system and
the chimney wall, to but not past the inner flue liner face.
2. A chimney connector shall not pass through an attic or roof space,
closet or similar concealed space, or a floor, or ceiling.
3. Where passage through a wall, or partition of combustible construc-
tion is desired, the installation shall conform to CAN/CSA-B365.
13
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND OPERATION
Minimum Chimney Clearance to Brick &
Combustibles – 2 in. (51mm)
A
Primary Air Draft Control
Use the air control adjustment tool (provided - see FigrueX 10) to adjust
the air controls per the following instructions.
Min. Clearance 12 in.
(304.8mm) of Brick
Chimney
Connector
Fire Clay
Liner
Min. 12 in. (304.8mm)
to Combustibles
Minimum Chimney Clearance from Masonry to Sheet Steel
Supports & Combustibles – 2 in. (51mm)
B
Nonsoluble
Refractory
Cement
Min. Clearance
9 in. (228.6mm)
Factory Built
Chimney Length
Chimney
Connector
Chimney Length
Flush with
UseChimney
Mfrs.Partsto
Attach
Inside of Flue
Air Space – 9 in.
(228.6mm) Min.
Connector
Figure 10 - Air Control / Ash Pan Removal Tool
Solid-Insulated
ListedFactory-
BuiltChimney
Length
Masonry
Chimney
Sheet Steel Supports
The primary combustion air delivery is controlled by the Primary Air
Draft Control Assembly (located above the front door). The heat output
can be controlled by sliding the control to a higher or lower heat output
setting using the Air Control Tool Provided (See Primary Air Draft Control
below).
C
Min. Chimney Clearance from Masonry to Sheet Steel
Supports & Combustibles – 2 in. (51mm)
2 Air Channels, Each 1
in. (25.4 mm)
The fuel, the amount of heat and burn times desired, the type of installa-
tion are all variables that will affect the control setting. The same control
settings in a variety of installations will produce different results. You will
need to try different settings so you can learn how much heat to expect
and how long the fire will burn.
Chimney
Connector
Min. 6 in.
(152.4mm) glass
Fiber Insulation
2 Ventilated Air
Channels, Each
1 in. (25.4 mm)
Construction of
Sheet Steel
With the air control tool (provided in accessory package) the control can
be adjusted to the heat output desired (see Figure 11).
Masonry
Chimney
Sheet Steel Supports
Primary Air Draft Control
Using the air control tool (provided) slide
the control above door to adjust burn rate.
Min. Chimney Clearance from
Masonry to Sheet Steel Supports
& Combustibles – 2 in. (51mm)
D
Min. Clearance
2 in. (51 mm)
Sheet Steel
Supports
Lower Burn / Slide Left
Higher Burn / Slide Right
1 in. (25.4 mm)
Air Space to
Chimney
Length
Chimney
Section
Chimney
Connector
Chimney
Connector
Air Space – 2 in.
(51mm) Min.
Chimney
Length
Masonry
Chimney
Sheet
Steel
Supports
Figure 9 - Combustible Wall Chimney Connector Pass-Throughs
Figure 11 - Primary Air Draft Control
14
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
How To Start And Maintain A Fire
Adjusting Burn Rate:
1. Using the Air Control Tool (provided), open the Start-Up Air Control
Theprimaryairdraftcontrollocatedabovethefrontdoorcanbeadjustedto
the right for higher temperatures and to the left for lower temperatures.
(see Start-Up Air Control, on this Page).
2. Adjust the primary air draft control to the full open position (see
Generally, you will want to set the draft control somewhere in the low
or medium range
Primary Air Draft Control on Page 14).
3. Open the side fuel loading door and build your fire directly on the grate
in the firebox.
Tips - Adjust the primary air control to a medium to low setting for a slow
and more efficient burn. When burning on a higher setting, it is more
efficient to burn with a bright but not roaring fire.
a. Place five or six loosely crumpled sheets of newspaper in the
stove.
Start Up Air Control (Ignition Booster)
b. Add a small amount of dry kindling randomly on the top of the
newspaper.
To facilitate lighting, your stove is equipped with an ignition booster,
which brings start-up air to the fire for a short period of time. This can
be especially helpful when your chimney is cold. The ignition booster can
also be used to allow the fire to recover quickly following refuelling.
c. Place a few more loosely crumpled newspapers on top of the
kindling and light the bottom paper first, then light the top paper.
Once the fire is well underway, close the door. The upper fire
should preheat the chimney and create an effective draft while
the lower fire ignites the kindling.
IMPORTANT
The Start-Up Air Control provides supplemental
primary air. Do NOT leave the start-up air contol
in the open position for more than five minutes
(this could result in dangerous overfiring which is
not covered under the warranty). Close by pushing
the lever inwards.
4. After the kindling is burning well, add increasingly larger pieces of
wood until the fire is actively burning (see bullets below). Leave the
fuel door open (slightly ajar for 5 minutes). Then close the stove door.
Never leave the stove unattended when the door is open.
• When loading fuel, be careful not to smother the fire.
• Load logs evenly across the base being cautious not to place
wood in front of the rear edge of the log guard.
5. Onceabedofcoalshasbeenestablished,adjusttheprimaryaircontrol
to a lower setting AND CLOSE THE START-UP AIR CONTROL.
Stove Back
Air Delivery Systems
Tip – Using the air control tool, adjust the primary air draft control to
a medium to low setting for a slow and more efficient burn. On higher
settings, it is more efficient to burn with a bright but not roaring fire.
When Refueling
Slide to Open
Start-Up Air
Control Module
1. Follow the normal procedure for refuelling described on Page 17.
However, instead of cracking the door open 1/2," open the start-up
air control by pulling the lever outwards. This will supply enough
primary combustion air to allow the fire to recover.
Figure 12 - Start-up Air Control
Before Initial Lighting
1. Using the air control tool open the start-up air control by pulling the
lever outwards (see Figure 12).
2. Load fuel into the firebox and light the fire as usual (see How To Start
And Maintain A Fire on Page 15).
15
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Ash Removal Door And Side Fuel Loading Door
Primary Air
Control
CAUTION
Whenopeningthedoors,donotextendthembeyond
their normal travel. Overextending the doors to a
further open position can put excessive stress on
the hinge area of the doors which may result in
breakage.
Secondary Air
Tubes (2)
Latch Assemblies
(For front ash removal door, side fuel loading door and ash drawer
door).
Permanent
Secondary
Combustion Air
Intake. Secondary
air is delivered
through this opening
to ignite secondary
gases. There is no
adjustment control
for this intake.
The door latch assemblies are designed to securely latch the front door,
sidedoorandashdrawerdoor. Toopenthelatches, insertthedoorhandle
(provided) into hole in the latch assembly and rotate counterclockwise
until door releases. To close and latch, reverse the process
Glass
Permanent Primary Air Intake. Supplimental primary air is delivered
through this small opening (to improve efficiency). There is no adjustment
controls for this intake.
The glass is a 5 mm super heat resistant ceramic that withstands con-
tinuous temperatures up to 1256° F. This temperature is well beyond
the temperatures in which you operate your stove.
Figure 13 - CI1000HT Side Cut-A-Way View
These models are designed to provide a flow of air over the inside of the
glass, where along with high heat helps keep it clean. When operating
the stove on low for extended periods of time, the glass may get dirty.
A short, hot fire (15 - 20 minutes) will help clean off much of the normal
buildup (see Dirty Glass, Page 21). A commercial glass cleaner designed
for stoves is recommended for cleaning.
Primary Air
Control
The glass should be cleaned thoroughly with glass cleaner and a soft
cloth BEFORE the stove is burned.
Secondary Air
Start-up
Use Control Settings That Work For You
Tubes (3)
Air Control.
See Start-Up
Air Control on
Page 15.
CAUTION
Never leave stove unattended on high settings.
The fuel, the amount of heat you want, the type of installation you have
and how long you wish the fire to burn are all variables that will affect
the control setting. The same control settings in a variety of installations
will produce different results.
Supplemental
Secondary
Air Delivery
Secondary Air is
delivered through
this opening to ignite
secondary gases.
There is no
Familiarizeyourselfwithyourstovebytryingdifferentsettingssoyoucan
learn how much heat to expect and how long the fire will burn. It may take
a week or two to learn but your patience will be rewarded by the warmth
and pleasant satisfaction that only a wood fire can provide.
adjustment control
for this intake.
Replenish Humidity Level Of Dwelling
Figure 14 - CI2000HT Side Cut-A-Way View
Heating the air in a closed building decreases the relative humidity of the
air, which will dry wood and other combustible materials. This drying
lowers the ignition temperature of these materials, thus increasing the
fire hazard. To reduce the risk of fire, some provision should be made
for replenishing moisture to the air whenever a structure is being heated
for extended periods.
16
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
Refueling
Burn-In Period
Your stove finish is a high temperature paint that requires time and
temperature to completely cure. We recommend that you ventilate the
house during the initial burns. The paint emits non-toxic odors during
this process.
CAUTION
Always check for high flames when opening a door
by partially opening door for a few seconds before
opening fully.
KEEPYOURHOUSEWELLVENTILATEDDURINGTHECURINGPROCESS
TO PREVENT ACTIVATION OF YOUR HOME SMOKE DETECTOR.
It will take approximately three burn cycles to cure the paint. The first two
burns should be low heat, approximately 250°F., for 20 minutes each,
using paper and light kindling.
To prevent smoke blowing into the room follow these recommenda-
tions:
After each 20-minute burn, allow the appliance to cool completely. The
third burn should be at least medium high or about 450°F. for 45 - 60
minutes. The paint will become soft and emit non-toxic haze during these
burns. Keep the area well ventilated.
1. Using the air control tool adjust the primary air draft control and
start-up air control to the full open position and let the fire “liven up”
for about one minute before opening the fuel loading door. Open door
about 1/2” and hold in this position about 30 seconds or until stove
is drafting well, then fully open the door.
As the paint cures it will become slightly lighter in color. Eventually the
entiresurfacewillbecomeanevencolor.Oncethepainthasbeensoftened
and cooled two or three times, it will harden. Do not place anything on
the stove surface until the paint is completely cured. Do not attempt to
repaint the stove until the paint is completely cured. If the surface later
becomes stained or marred, it may be lightly sanded and touched up with
spray paint from the same paint (See Small Area Paint Touch-Up, Page
19). Paint is available at your local authorized Lennox Hearth Products
dealer. Never attempt to paint a hot stove.
2. Rake the embers towards the front of the stove and spread evenly. If
there are logs only partially burned rake these to the front of stove.
• Feed the logs to the embers. When loading wood, add one or
two logs at a time, depending on size. Try and use the side fuel
loading door as it will allow for cleaner operation. Load logs
evenly across the base being cautious not to place wood in front
of the rear edge of the log guard.
• Close the fuel loading door.
First Fire
• With the primary air draft control in the full open position. Crack
the door open about 1/2” and let it burn for approximately 5
minutes. Then close the door and adjust the primary air draft
control to the desired setting and CLOSE THE START-UP AIR
CONTROL.
Note: There is often an unpleasant odor and non-toxic fumes during the
first initial burns (this is a natural result of the paint curing). We recom-
mend that a window should be left open near the appliance during this
curing process. See Burn-In Period on Page 17.
• In order to maintain an attractively burning fire, logs should
be up to 18” (457 mm) long and well seasoned. Loading the
appliance full of damp wood on a low fire is certain to cause low
combustion efficiency resulting in tar and dirty glass.
• High combustion temperatures are the secret to clean glass
operation.
When your installation has been completed and inspected you are ready
to build your first fire.
1. Using the air control tool, open the primary air draft control to the full
open position (see Primary Air Draft Control, Page 14).
2. Open fuel loading door and build a small fire in the stove using tightly
rolled paper and dry kindling. Wait a few minutes for a good updraft
to establish the fire.
3. Now place two or three thoroughly dried logs on the burning kindling
and secure door.
5. After about 25-30 minutes of burning (when fire is well established),
slide the primary air draft control to a medium setting. This will keep
the fire burning at a moderate level so heat is transferred through the
stove rather than up the chimney.
6. Once a bed of coals has been established, adjust the primary air draft
control to a low setting.
Overnight Burning
To inhibit excessive build-up on the glass during a slow overnight burn, it
is recommended that the primary air draft control be adjusted to at least
a slightly open position (the optimum setting will depend on how well
your chimney draws). To achieve a slow burn (the maximum burn time
is 8 hours under optimum conditions - dry, high BTU wood such as oak
and proper draft from the chimney).
7. During the first few fires, keep the combustion rate at a low to moder-
ate level. Avoid burning fires with the primary air control wide open
for long periods of time. This results in an updraft fire with most of
the heat escaping up the chimney.
Note: With a good drafting chimney, the primary air control will need to
be closed further than with a poor drafting chimney.
FUEL
WARNING
Burn Recommended Fuel
Read and use the information provided in this sec-
tion.Todisregardthismaycauseseriouspermanent
damage to the stove and void your warranty. It is
best to warm your stove up slowly and keep it at a
moderate level.
This appliance is designed for use with natural well-seasoned wood. Do
NOT burn particleboard scraps or pressed logs because they can produce
conditions which will deteriorate metal. Green or uncured wood does not
workwellasfuel, andcancauseincreasedcreosotebuildups. Thevalueof
green wood as a source of heat is limited. Do not overload or use kindling
wood or mill ends as primary fuel as this may cause overfiring. Overfiring
is a condition where excessive temperatures are reached, beyond the
design capabilities of the stove. The damage that occurs from overfiring
is not covered under the stove warranty.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Why Season Wood?
What is the best wood for the fire?
Some woods are easier to light than others (i.e. hornbeam, beech, & oak
do not light easily whereas aspen, birch and lime light easily but they do
not last as long). Then come the softwoods and conifers. Regardless if
you are burning a softer or harder wood, what is most important is that
it is well-seasoned dry wood. Damp wood has far less heating power,
this lowers the combustion temperature of the fire therefore, the output.
Green wood is difficult to light, it burns badly and gives off smoke and
causestheformationofdeposits(tarringandsootstaining)inthechimney
flue and on the door glass.
Thekeytothesuccessofagoodfirethatproducesheatfromawoodstove
is the wood. It needs to be well-seasoned natural wood.
What does “Well-Seasoned” mean?
When a tree is cut down, the wood is green, full of sap and moisture.
This moisture content can exceed 80%, which must be reduced to less
than 20%. Wood properly seasoned is then capable of generating the
heat the stove was designed to provide.
What is tarring and soot staining in the chimney?
When the smoke arrives in the chimney at low temperature, part of the
water vapor which they convey condenses. The heaviest constituents
are deposited on the inside of the flue (this is TARRING). The mixture
oxidizes in the air and forms brownish patches (this is SOOT STAINING).
Four essential points for avoiding these drawbacks, use dry wood, use
a stove designed for wood, connect it to a chimney with thick walls and
of suitable cross-section (size and height), and ensure the connecting
pipes are as short as possible. Horizontal pipes should be no more than
6” (150 mm).
Green wood does not burn easily. Attempting to burn green wood often
results in a lot of smoke and very little fire. Time is the most important
factorinseasoningwood. Ideallythemoisturecontentshouldbereduced
to 11-20%, although very few of us will be able to check that figure.
There are several steps that should be taken to ensure that you come
close to these figures.
Seasoning Guide
Flue Gas Temperature
Softwoods – 18 months
It is recommended to thoroughly heat the flue system during start-up,
before adjusting the burn rate to a medium or low setting (see How To
Start And Maintain A Fire, Page 15). To ensure that the flue system is
thoroughly heated, adjust the primary air to a medium/high position for
approximately20-25minutesafterthestart-upairisclosedbeforeadjusting
to a lower setting. This helps to establish the draft and it reduces creosote
deposits on the internal surfaces of the stove, glass and chimney.
Hardwoods – 18 months to 24 months
This period can be shortened (12 to 15 months) if the wood is cut to the
right length and immediately stored under a ventilated shelter.
Logs that are 5” diameter across or larger should be split in half, three
pieces if over 8 inches, and four pieces when over a foot across (split
wood dries quicker than round logs). Round logs left in the open for
more than a year end up rotten. If the tree was fell 2 to 4 years ago, it
still needs to be cut, split, and seasoned for 18 to 24 months depending
on the wood.
Hints:
• Creosote condenses in a cold chimney, not a warm one. Avoid a
smoldering fire for more than a twelve-hour period and your chimney
will never get cold.
• Burn a hot fire for a short period once or twice a day (and after reload-
ing), and then adjust the primary air draft module to a medium or low
position.
• When loading wood, add one or two logs at a time, depending on
size. Loading the appliance full of damp wood on a low fire is certain
to cause poor combustion efficiency resulting in creosote and dirty
glass.
Wood which is too small to split must be drained, by removing some
of the bark.
Wood Storage
• If the wood is not quite as dry as it should be, to assist for a short
period, smokeless coal can be added with the wood to raise the
combustion temperature.
• Have the chimney cleaned and inspected by a professional chimney
sweep once a year.
Woodtobeseasonedshouldbestackedinanareaopenenoughtoensure
good air circulation on both sides – leaving adequate space between
woodpiles to walk comfortable. Do not stack wood against a wall or
building. It helps to elevate the wood piles off the ground (two 2 x 4’s
running lengthwise beneath the woodpile works well). This allows air to
flow under the bottom logs.
WARNING
Burning improper fuel (i.e. Charcoal) can result
in carbon monoxide poisoning which may lead to
death!
Carbon monoxide poisoning – early signs of carbon
monoxide poisoning resemble the flu with head-
aches,dizziness,ornausea. Ifyouhavethesesigns,
get fresh air at once! Have the heater inspected by
a qualified service technician. Some people are
more affected by carbon monoxide than others.
These include pregnant women, people with heart
orlungdiseaseoranemia,thoseundertheinfluence
of alcohol, and those at high altitudes.
Store wood in a cool, dry place, well away from any source of flame or
heat. Keep paper, wood, rags and other easily ignited materials away
from the wood. If wood should become wet, separate it and allow it to
dry naturally; do not mix wet and dry wood or pile wet wood on top of
dry wood. If wood is kept outdoors, either covered with a tarp, or not
covered at all, it will not burn well until it has been in an enclose space
for one to two months. If stored outside, keep the wood covered to
protect from rain or snow.
Woodsuppliedinready-cutlengthsstoredimmediatelyunderaventilated
shelter dries quicker than wood stocked in high piles.
18
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
NEVER PLACE ASHES IN A CARDBOARD BOX OR ANY OTHER COM-
BUSTIBLE RECEPTACLE.
MAINTENANCE
Proper Disposal of Ashes:
WARNING
Ashes should be placed in a metal container with a tight fitting lid. The
closed container of ashes should be placed on a noncombustible floor
or on the ground, well away from all combustible materials, pending
final disposal.
Do NOT clean the stove while it is hot!
IMPORTANT
Iftheashesaredisposedofbyburialinsoilorotherwiselocallydispersed,
they should be retained in the closed container until all cinders have
thoroughly cooled.
Inspect the entire stove frequently for proper
operation, fit and soundness of parts. If any mal-
functioning, cracked, broken, or loose parts or
other problems are noted, contact your dealer or
qualified serviceman to inspect and repair the unit.
Do not operate the unit if installed or functioning
improperly.
Door, and glass gaskets
If the gaskets which provide a seal around the doors or glass should
become frayed or damaged they should be replaced with the same size
and type as the original gasket. Contact your dealer for ordering. Use
high temperature silicone sealer as an adhesive for the door gasket. The
glass gasket has a self-adhesive backing (see Replacement Parts on
Pages 24 through 30). If the gasketing is in good condition, check the
closure latch screws; if these are loose, tighten with a phillips screwdriver
(do not overtighten).
Summer Shut Down
Remove ashes and cinders from the stove and dispose of (see Ash
Removal and Disposal on this page). If the room is damp, place some
absorbent crystals inside the stove and/or disconnect it completely from
the chimney. Close doors and secure the latches closed.
WARNING
The gaskets must be kept in good condition. Do not
leave the stove burning with the fuel loading doors
open or ajar. This will cause excessive heat build
upintheunitandcouldignitesurroundingcombus-
tibles as well as damage the stove by overfiring it.
Overfiring is a condition where excessive tempera-
tures are reached, beyond the design capabilities
of the stove (such damage is not covered by the
manufacturers warranty).
Cleaning Heater Surface
Clean the heater surface with a dry or slightly damp cloth. In case of
condensation, clean the affected areas before they dry.
Small Area Paint Touch-up
The stove body is painted with a quality high-temperature stove paint.
Use only Stove Paint, Catalog #40M6801. Do not touch-up your stove
with any other paint.
Usingonesmallpieceof320gritsandpaperandlightlysandtheblemishso
that the edges are “feathered” or smooth to the touch between the painted
and bare surfaces. Do not let the sand paper gum up with paint, as this
will cause scratches on the metal surface. If there are any scratches, use
600 grit sandpaper instead. Mask off surfaces you do not want painted.
Paint lightly over the bare surface first as this will act as an undercoat.
Then paint over a larger area in smooth even strokes to blend.
Firebrick
The firebrick should be inspected periodically and replaced if damaged
(crumbling or excessively cracked). Through normal wear and tear, the
firebrick may need to be replaced over time (through proper installation,
operation, maintenance and fuel, the longevity of the firebrick will be
increased–seeOverfiringDamage,Page21).Forinformationonwarranty
of the firebrick, see warranty statement provided with the appliance.
See Burn-In Period on Page 17 for information on curing the paint.
Ash Removal And Disposal
CAUTION
Empty the ash pan regularly to prevent the ash from spilling over. Do not
allow the ash to build up and touch the under side of the grate.
Be careful not to abuse door assembly by striking
or slamming it. If the door assembly or glass is
broken or damaged, they must be replaced with
factory original parts before heater can be safely
operated. Use only components provided by the
manufacturer as replacement parts.
To remove the ash from the stove, operate the firebox grate using the
handle.
A layer of ash left over the grate when burning wood will protect the grate
and retain heat so encouraging clean combustion.
The tool provided for removal of the ash pan should not be used to carry
the ash pan. Use a leather glove and hold the ash pan on both sides.
Ashes can hold live embers for several days, and must be disposed of
with care.
Cleaning Glass
Ensure stove is cold prior to cleaning glass. A commercial glass cleaner
designed for stoves is recommended. Do not use abrasive cleaners. Do
not clean with any materials, which may scratch or otherwise damage the
glass. Scratches on the glass can develop into cracks or break. Inspect
the glass regularly. If you detect a crack, extinguish the fire and contact
your dealer for a replacement.
WARNING
Make sure that the fire is out and the stove is cold
before removing ashes!
19
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning - Remove the baffle brick in the firebox prior to having your
chimney cleaned (should be done by a qualified chimney sweep). See
following – Removing Baffle Brick for Cleaning).
Replacing Glass:
1. Open the door. Using a phillips screwdriver loosen the four (4) screws
which secure the glass then carefully remove broken glass one piece
at a time (protective leather gloves are recommended).
Removing Baffle for Cleaning
2. Remove screws and clips from doorframe and set aside.
Beforefluecanbecleaned,thebaffleinthestovefireboxmustberemoved.
The CI1000HT has one vermiculite firebrick, which serves as a baffle for
the flue gasses. The CI2000HT has a 5-sided box made of ceramic fiber
brick that serves as a baffle. In both cases, the baffles are located just
above the secondary air tubes (which must be removed to access the
baffle). Suggestion: Wear a pair of leather work gloves when removing
secondary air tube assembly and baffle.
Door Frame
4 Ea. Clip
Gaskets
4 Ea. Glass
Clips
1. Toaccessthebaffle,thesecondaryairtubeassemblymustberemoved.
Locate the four (4) screws, which secure the assembly into place
(located at the ceiling of the firebox). Remove the assembly and set
aside. Slide the baffle out and set aside.
4 Ea. Glass Clip Screws
Glass
Gasket
2. Once the baffle is removed from the firebox, the flue can be cleaned.
The accumulated soot that is removed by brushing will fall to the
firebox floor where it can be removed and disposed of.
Glass
Figure 15 - Replacing Glass
WARNING
Do NOT operate the stove without the baffle brick
properly installed. This will void the warranty and
the stove will not function properly.
3. Clean the area where the glass with gasket will be installed.
4. Install new glass with gasket (use only factory 4-mm glass with glass
channel gasket. Do not substitute).
5. Carefully reinstall glass clips with gasket and screws. Be very careful
not to overtighten the screws (this could result in breakage when
stove is hot).
IMPORTANT
Creosote Formation And Need For Removal
IN THE EVENT OF A CHIMNEY FIRE - Make sure the
fuel loading doors are securely closed. Adjust the
primaryairdraftcontroltothelowest(mostclosed)
setting and ensure that the start-up air control is
closed. Call the fire department immediately.
After a chimney fire, the complete chimney system
should be checked by a qualified technician before
further use.
What is Creosote - When wood is burned slowly, it produces tar and
other organic vapors, which combine with expelled moisture to form
creosote. The creosote vapors condense in the relatively cool chimney
flue of a slow-burning fire. As a result, creosote residue accumulates
on the flue lining. When ignited this creosote makes an extremely hot
fire. Also, creosote deposits tend to form in long runs of venting where
gases become too cool prior to exhausting. Note: Single wall pipe cools
rapidly, therefore installations using this type of flue are more susceptible
to creosote deposits.
Consultyourdealerforsuggestionsonproperchim-
neycare.Contactyourlocalmunicipalorprovincial
fire authority for information on how to handle a
chimney fire. Have a clearly understood plan for
handling a chimney fire. Establish a routine for the
fuel, stove and firing technique. Check daily for
creosotebuild-upuntilexperienceshowshowoften
you need to clean to be safe. Be aware that the
hotter the fire the less creosote is deposited, and
weekly cleaning may be necessary in mild weather
even though monthly cleaning may be enough in
the coldest months.
To inhibit the build up of creosote, adjust the primary air draft control to
a medium-high or high setting for a 10-minute period each day. Do not
attempt to burn out heavy creosote accumulations in this manner. This
must be removed from the chimney by scraping or brushing to reduce
the risk of a chimney fire.
Burn Approved Fuel Only - This stove is approved for burning dry sea-
soned natural wood only. Using green or inadequately seasoned wood
may increase creosote buildup.
Inspection Frequency - The chimney connector and chimney should
be inspected at least twice monthly during the heating season to deter-
mine if a creosote buildup has occurred. If creosote has accumulated it
should be removed to reduce the risk of a chimney fire. If creosote has
accumulated (1/8" [3 mm] or more) it should be removed to reduce the
risk of a chimney fire. Experienced chimney servicing personnel should
be consulted.
Reinstall Baffle Brick
After your chimney has been swept, reinstall the baffle brick (see Remov-
ing Baffle for Cleaning and reverse steps).
20
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
*
Draft problems; if installing into a larger flue, it may be necessary
to use a full-length liner to achieve adequate draft for the appliance.
A draft gauge should read a minimum of .05” W.C. (inches water
column) not to exceed .06” W.C. for optimum performance (See Draft
Requirements on Page 11).
* When Fuel Door Is Opened, Smoke Enters Room
1. The primary air draft control is closed.
2. The chimney is too cool. Set the primary air draft control on “HIGH”
for a few minutes before opening either fuel loading door.
3. Excess creosote will not only restrict your draft but it will create a
risk of a creosote fire. Strictly adhere to maintenance requirements as
outlined in this manual. If excess creosote has built up on the inside
of the firebox sides and door, burn a small hot fire at intervals that
are more frequent with air control on HIGH for a few minutes.
4. Deposits may have built up in the chimney and are restricting the
draft, or the spark arrester on top of the chimney may be plugged.
5. Chimney diameter too large or too small to provide adequate draft.
6. The house is too airtight (usually takes 20 to 30 minutes for problem
to appear as stove lowers air pressure in house). Crack a window
open or provide an outside source of air near stove.
OVERFIRING DAMAGE
Iftheheaterorchimneyconnectorglows, youareoverfiring. Othersymp-
tomsmayinclude:Cracking,warpingorburningoutofcomponents,stove
glass may develop a haze, which will not come off with cleaning.
Overfiring of a stove is a condition where excessive temperatures are
reached, beyond the design capabilities of the appliance. The damage
that occurs from overfiring is not covered under the manufacturers
limited warranty.
7. Insufficient vertical height to chimney to achieve adequate draft.
Thefollowingareafewconditionsthatshouldbeevaluatedand(corrected
if necessary) if an overfiring condition is suspected:
Does Not Produce Enough Heat
Overfiring Caused From Improper Installation
1. Using green or insufficiently cured wood.
2. Excessive draft.
Ensure that all installation requirements have been met as outlined in the
installation manual. The chimney should be clean and in good repair. A
draft test should be performed to determine if the draft requirements of
the appliance are being met. A draft gauge should read between .05 and
.06 “ W.C. (inches water column). Excessive draft (above .06 “ W.C.) will
allow too much combustion air to be pulled in which results in hotter
burns. Too little draft (below .05 “ W.C.) will not allow enough combus-
tion air delivery to maintain a fire (this may result in improper operation
of appliance, i.e. wont maintain fire unless fuel loading door is left open.
See following, Overfiring Caused From Improper Operation).
3. High ceilings (heat rises quickly, but can be recirculated by a well-
placed ceiling fan with a winter/summer switch).
4. The area to heat is too large (square foot heating estimates are based
on “average” climates and home design).
5. There is an obstruction in the chimney.
6. The chimney or chimney cap is restricted by creosote preventing
enough draw to sustain a “high” heat output rate.
* Does Not Maintain A Fire
1. Soft wood does not burn as long or as well as seasoned hardwood
resulting in a short burn time.
Overfiring Caused From Improper Operation
2. Wood size too small. Burns at too rapid a rate.
3. The gasket seal on the fuel loading doors, or glass is leaking air. Repair
or replace it if necessary.
Operate this appliance only as outlined in this manual. Never burn the
appliance with either fuel loading door open or ajar. Do not operate this
stove with the Primary Air Draft Control in the full “open” position for
extended periods. This wastes fuel and can cause dangerous overfiring
conditions. NEVER leave the stove unattended on high settings.
4. Excessive draft.
5. There may be an obstruction in the chimney.
* Backpuffing
Definition: This is a term describing the condition when combustible
gasesremainunlitbecauseofinsufficientcombustionairdeliverywhich
resultsincombustiblegasesbuilding,thenflashigniting.Ifbackpuffing
isoccurring, itcanpushsomesmokeintotheroomthroughtheprimary
or secondary air openings. The combustion air delivery is dependent
uponthedraftoftheventingsystem.Thefollowingarevariables,which
can negatively affect the draft resulting in backpuffing.
Overfiring Caused From Improper Maintenance
Strictly adhere to all maintenance requirements at frequent intervals as
prescribed in this manual including cleaning of flue and stove. Should
either fuel loading door or glass gaskets become worn or damaged, they
should be replaced.
1. Downdraft in the chimney (a special wind cap may be needed).
2. The house is too air tight (ventilation is needed).
3. Insufficient vertical height to chimney to achieve adequate draft.
Overfiring Caused From Improper Fuel
This appliance is approved for use with natural dry well-seasoned wood
only (ask your authorized dealer what are approved fuels for your area).
Do not burn garbage, particleboard scraps, or pressed logs because
they can produce conditions that will deteriorate metal. Do not overload
or use kindling wood or mill ends as primary fuel as this may cause
overfiring.
Odors
1. Creosote accumulation in firebox (brush out on next cleaning).
2. Chimney downdraft when stove is not operating (close the primary
air draft control).
3. Paint curing on first several burns.
* Dirty Glass
1. Poor draft conditions.
2. Long burn periods at low draft settings.
3. Burning wet, pitchy or spongy wood.
4. Poorly arranged logs (too close to glass).
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS - Model CI1000HT
Flue position
Top
FRONT VIEW
23-3/4"
(604 mm)
Flue collar size
Approx. burn time
Maximum burn rate
EPA BTU Range
6” (152 mm)
6 to 8 hours
87,301 BTU
11,500 – 55,000 BTU
6"
(152 mm)
Emissions Rate (grams/hr) 4.42 grams
Maximum Log length
Firebox Size
18” (457 mm)
30"
(762 mm)
1.12 cu. feet
27-1/4"
(693 mm)
Loading
Front & Side
Width (overall)
23-3/4” (604 mm)
15-5/16” (389 mm)
30” (762 mm)
Depth (overall)
4-1/8"
(105mm)
Height (to flue)
* Shown with optional window trim
Height (to stove top)
Back to centerline of flue
Approx. weight with brick
27-1/4” (693 mm)
6-7/16” (163 mm)
~280 lbs. (140 kg)
SIDE VIEW
15-5/16"
(389 mm)
Note: Dimensions shown are approximate only (+/- 1/4”).
8-15/16"
(226 mm)
6-7/16"
(163 mm)
17-3/16"
(436 mm)
22
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS - Model CI2000HT
FRONT VIEW
Flue position
Top
29-1/8"
(740 mm)
Flue collar size
Approx. burn time
Maximum burn rate
EPA BTU Range
6” (152 mm)
6 to 8 hours
96,662 BTU
11,923 – 60,897 BTU
6"
(152 mm)
Emissions Rate (grams/hr) 2.72 grams
Maximum Log length
Firebox Size
22” (559 mm)
32-13/16"
(833 mm)
1.97 cu. feet
29-3/4"
(756 mm)
Loading
Front & Side
Width (overall)
29-1/8” (740 mm)
18-3/4” (476 mm)
32-13/16” (833 mm)
29-3/4” (756 mm)
7-11/16” (195 mm)
~410 lbs. (205 kg)
Depth (overall)
Height (to flue)
3-15/16"
(100mm)
* Shown with optional window trim
Height (to stove top)
Back to centerline of flue
Approx. weight with brick
SIDE VIEW
18-3/4"
(476 mm)
Note: Dimensions shown are approximate only (+/- 1/4").
10-3/4"
(274 mm)
7-11/16"
(195 mm)
21-9/16"
(547 mm)
23
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS LIST - Models: CI1000HT & CI2000HT
Item
31
32
33
34
35
35
36
36
Cat. No.
40M5701
40M6901
40M2301
40M9801
40M2101
40M8601
40M3901
41M0501
40M3601
41M0301
40M5101
41M0401
41M0101
40M2701
40M9001
40M0701
40M4301
40M1701
40M8201
40M1201
40M7801
40M3501
41M0201
41M3901
41M3801
41M4001
41M3701
41M4101
41M5501
41M4901
41M5001
41M5101
41M5401
41M5201
41M5301
40M7201
40M9301
Description
Where Used
CI1000HT
CI2000HT
CI1000HT
CI2000HT
CI1000HT
CI2000HT
CI1000HT
CI2000HT
CI1000HT
CI2000HT
CI2000HT
CI2000HT
CI1000HT & CI2000HT
CI1000HT
CI2000HT
CI1000HT
CI2000HT
CI1000HT
CI2000HT
CI1000HT
CI2000HT
CI1000HT
CI2000HT
CI1000HT
CI1000HT
CI1000HT
CI1000HT
CI1000HT
CI2000HT
CI2000HT
CI2000HT
CI2000HT
CI2000HT
CI2000HT
CI2000HT
CI1000HT
CI2000HT
Air Column Set, Left & Right (Includes Gaskets & Screws)
Air Column Set, Left & Right (Includes Gaskets & Screws)
Air Deflector (Air Wash), Upper (Includes Hardware)
Air Deflector (Air Wash), Upper (Includes Hardware)
Ashlip, Charcoal, Painted (Includes Gasket & Screws)
Ashlip, Charcoal, Painted (Includes Screws)
Ashpan Assembly
Ashpan Assembly
Back, Steel Stove (Includes Hardware)
Back, Steel Stove (Includes Hardware)
Baffle Assembly, ceramic fiber brick (Baffle Box)
Channel Assembly, Start-Up Air (Includes Gasket And Hardware)
Clip Set, Glass (Includes 4 Ea. Gaskets, Screws & Clips)
Collar Kit, Charcoal Replacement Flue (Includes Gasket & Hardware)
Collar Kit, Charcoal Replacement Flue (Includes Gasket & Hardware)
Door, Ashpan, Charcoal (Handle Receiver Not Included)
Door, Ashpan, Charcoal (Handle Receiver Not Included)
Door, Firebox, Charcoal (Handle Receiver Not Included)
Door, Firebox, Charcoal (Handle Receiver Not Included)
Door, Side Loading, Charcoal (Handle Receiver Not Included)
Door, Side Loading, Charcoal (Handle Receiver Not Included)
Draft Module, Air Intake (Slide Assembly) Includes Gasket & Hardware
Draft Module, Air Intake (Slide Assembly) Includes Gasket & Hardware
Firebrick, Left
37
38
39
40
3
4
1
1
2
2
47
48
12
13
14
15
16
5
Firebrick, Lower Rear
Firebrick, Right
Firebrick, Baffle (vermiculite)
Firebrick, Upper Rear
Firebrick, Bottom Center
6
Firebrick, Bottom Side (left or right)
7
Firebrick, Left Lower
8
Firebrick, Left Upper
9
Firebrick, Lower Rear
10
11
17
18
Firebrick, Right Lower
Firebrick, Upper Rear
Frame, Fuel Grate (bottom)
Frame, Fuel Grate (bottom)
Note: The item numbers correspond to component diagrams on Pages 26 through 30
24
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS LIST - Models: CI1000HT & CI2000HT
Item
Cat. No.
Description
Where Used
40M4501
Gasket Kit, 6 mm x 156 cm (14979) For Air Intake Slide & Glass & 4 ea. 6mm Glass
Clip Gaskets (31856)
CI1000HT & CI2000HT
40M0201
40M4201
Gasket Kit, Ashpan Door Rope (8 mm Dia. X 97 cm)
CI1000HT
Gasket Kit, Rope (10 mm Dia. x 146cm) Ashpan Door - CI2000HT, Side & Front
Firebox Door - CI1000HT
CI1000HT & CI2000HT
40M4401
40M4901
Gasket Kit, Rope (12 mm Dia. x 177 Cm) Front & Side Door CI2000HT
CI2000HT
19
Gasket Set, Air Column, 70mm X 45mm (Also Includes Start Up Air Channel - Model
CI2000HT Only)
CI1000HT & CI2000HT
41M3601
40M5401
41M0801
40M4001
40M1301
40M2901
40M9601
40M5301
40M4101
40M5601
40M5801
41M0901
40M9501
41M3101
40M2801
40M9701
40M68
Gasket, Flue Outlet
CI1000HT
CI1000HT
Glass, Replacement, 10.39” X 14.02” (Includes Gasket)
Glass, Replacement, 18.82” X 12.52” (Includes Gasket)
Grate Support Bar, Fuel
CI2000HT
20
21
22
23
24
25
26
27
28
28
28
29
30
CI1000HT
Grate, Ash Removal
CI1000HT
Grate, Fuel
CI1000HT
Grate, Fuel
CI2000HT
Hinge Pin Set, Ashpan Door (Includes 2 Hinge Pins, 2 Acorn Nuts & 2 Washers)
Hinge Pin Set, Firebox Door (Includes 2 Hinge Pins, 2 Acorn Nuts & 4 Washers)
Hinge Pin Set, Firebox Door (Includes 2 Hinge Pins, 2 Acorn Nuts & 4 Washers)
Hinge Pin Set, Side Door (Includes Hinge Pins, 2 Acorn Nuts & 2 Washers)
Leg, Front Left, Charcoal (Includes Gasket & Hardware)
Leg, Front Right, Charcoal (Includes Gasket & Hardware)
Leg, Right & Left Rear, Charcoal (Includes Gasket & Hardware)
Log Guard (With 2 Andirons)
CI1000HT & CI2000HT
CI1000HT
CI2000HT
CI1000HT & CI2000HT
CI1000HT & CI2000HT
CI1000HT & CI2000HT
CI1000HT & CI2000HT
CI1000HT
Log Guard (With 3 Andirons)
CI2000HT
Paint, Touch-Up Spray, Charcoal, 1 Spray Can
Poker, Fire
CI1000HT & CI2000HT
CI1000HT & CI2000HT
CI1000HT
41
42
42
42
42
42
49
40M6201
40M5201
40M0301
40M1001
40M3801
40M6101
41M5601
Receiver Assembly, Ashpan Door Handle (Includes Latch)
Receiver Assembly, Ashpan Door Handle (Includes Latch)
Receiver Assembly, Firebox Door Handle (Includes Latch)
Receiver Assembly, Side Door Handle (Includes Latch)
Receiver Assembly, Side Door Handle (Includes Latch)
CI2000HT
CI1000HT & CI2000HT
CI2000HT
CI1000HT
Retainer Set, Firebrick (Includes 1 Left, 1 Right & 2 Rear Firebrick Retainers &
Hardware)
CI2000HT
41M4201
40M6001
40M0101
41M1001
40M5501
41M0601
Retainer, Firebrick Steel
CI1000HT
CI1000HT
43
44
45
46
Secondary Air Tube Kit (Includes Screws)
Secondary Air Tube Kit (Includes Screws & Washers)
Tool, Ashpan Removal / Air Control
Tool, Removable Door Opener
CI2000HT
CI1000HT & CI2000HT
CI1000HT &.CI2000HT
CI2000HT
Tube, Front Air Feed
Note: The item numbers correspond to component diagrams on Pages 26 through 30
25
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS - Models: CI1000HT & CI2000HT
(1) Front Firebox Door
(CI1000HT & CI2000HT Series)
(4) Ashpan Door
(CI2000HT Series)
(7) Left Lower Firebrick
(CI2000HT Series)
7.87” / 200 mm
.79” / 20 mm thick
(2) Side Loading Door
(CI1000HT Series)
(5) Bottom Center Firebrick
(CI2000HT Series)
7.87” x 200 mm
(8) Upper Left Firebrick
(CI2000HT Series)
10.43” / 265 mm
4.6” / 117 mm
.79” / 20 mm thick
(2) Side Loading Door
(CI2000HT Series)
(i9) Lower Rear Firebrick
(CI2000HT Series)
(6) Bottom Side Firebrick
(CI2000HT Series)
13.94” / 354 mm
12.36” / 314 mm
(i3) Ashpan Door
(CI1000HT Series)
.79” / 20 mm thick
.79” / 20 mm thick
2.87” / 73 mm
9.25” / 235 mm
26
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS - Models: CI1000HT & CI2000HT
(10) Right Lower Firebrick
(14) Right Firebrick
(CI1000HT Series)
(17) Fuel Grate Frame
(CI1000HT Series)
(CI2000HT Series)
8.47”/215mmx5.12”/
130mm(.98”/25mmthick)
10.43” / 265 mm
.79” / 20 mm thick
(11) Upper Rear Firebrick
(CI2000HT Series)
(18) Fuel Grate Frame
(CI2000HT Series)
13.93” / 354 mm
.79” / 20 mm thick
(15) Baffle Firebrick
(above tubes on ceiling)
(CI1000HT Series)
(12) Left Firebrick
(CI1000HT Series)
5.87” / 149 mm
x 14.36” / 365 mm
(19) Air Column Gasket
(CI1000HT & CI2000HT Series)
(.98” / 25 mm thick)
8.47”/215mm
x12”/305mm
(.79”/20mm
thick)
(16) Upper Rear Firebrick
(CI1000HT Series)
(13) Lower Rear Firebrick
5.51” / 140mm
x 12.60” / 320 mm
(CI1000HT Series)
6.50” / 165mm
x 12.40” / 315 mm
(.98” / 25 mm thick)
(19) Start-up Air Column Gasket
(.98” / 25 mm thick)
(CI2000HT Series)
27
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS - Models: CI1000HT & CI2000HT
(20) Fuel Grate Support Bar
(25) Front Firebox Door Hinge Pin
(29) Log Guard
(C1000HT Series)
(CI1000HT Series)
(CI1000HT Series)
(21) Ash Removal Grate
(CI1000HT Series)
(26) Front Firebox Door Hinge Pin
(30) Log Guard
(CI2000HT Series)
(CI2000HT Series)
(22) Fuel Grate
(CI1000HT Series)
(31) Left Air Column Assembly
(27) Side Door Hinge Pin
(CI1000HT & CI2000HT Series)
(CI1000HT Series)
(23) Fuel Grate
(CI2000HT Series)
(28) Stove Leg
(CI1000HT & CI2000HT Series)
(31) Right Air Column Assembly
(CI1000HT Series)
(24) Ashpan Door Hinge Pin
(CI1000HT & CI2000HT Series)
28
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS - Models: CI1000HT & CI2000HT
(32) Left Air Column Assembly
(35) Ashlip
(CI1000HT & CI2000HT Series)
(39) Flue Outlet Collar
(CI1000HT Series)
(CI2000HT Series)
(36) Ashpan
(40) Flue Outlet Collar
(CI1000HT & CI2000HT Series)
(CI2000HT Series)
(32) Right Air Column Assembly
Side View
(CI2000HT Series)
Top View
(37) Baffle Assembly, Ceramic Fiber Brick
(above secondary air tubes)
(CI2000HT Series)
(41) Fire Poker
(CI1000HT & CI2000HT Series)
(33) Upper Air Deflector
(CI1000HT Series)
(42) Ashpan, Side Door and Firebox
Door Handle Receivers
(CI1000HT & CI2000HT Series)
(38) Start-up Air Channel Assembly
(CI2000HT Series)
(34) Upper Air Deflector
(CI2000HT Series)
29
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS - Models: CI1000HT & CI2000HT
(43) Secondary Air Tube Assembly
(45)AirControl/AshPanRemovalTool
(CI1000HT & CI2000HT Series)
(48) Draft Module (Air Intake Slide)
(CI1000HT Series)
(CI2000HT Series)
(46) Removable Door Opener Tool
(CI1000HT & CI2000HT Series)
(49) Rear Firebrick Retainers
(CI2000HT Series)
Side Retainers Not Shown
(44) Secondary Air Tube Assembly
(CI2000HT Series)
(47) Draft Module (Air Intake Slide)
(CI1000HT Series)
CI2000HT Firebrick Placement Diagram
CI1000HT Firebrick Placement Diagram
Note:Therefractorybaffleassembly (37)onceiling(abovetubes), notshown.
CEILING
(15) Baffle Firebrick
(11) Upper
Rear Firebrick
BACK WALL
(9) Lower
Rear Firebrick
(16) Upper Rear Firebrick
(13) Lower Rear Firebrick
BACK WALL
LEFT WALL
LEFT WALL
RIGHT WALL
(8) Upper
Left Firebrick
(6) Bottom
Side
RIGHT WALL
(6) Bottom
Side
Firebrick
Firebrick
(7) Lower
Left Firebrick
(10) Lower
Right Firebrick
Note:
(5) Bottom Center
CI1000HT does
not have fire-
brick on fire-
box floor (fuel
grate & frame
on floor only).
Firebrick
(14) Right Side
Firebrick
(12) Left Side
Firebrick
FLOOR
30
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL ACCESSORIES - Models CI1000HT & CI2000HT
Catalog No.
41M2401
41M2001
Model
Description
Stove Model
CI1000HT
CI2000HT
WTK-CI10
WTK-CI20
Window Trim Kit, Charcoal
Window Trim Kit, Charcoal
31
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY/LISTING LABEL – Model CI1000HT
CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA
CONTACTEZ LE BUREAU DE LA CONSTRUCTION OU LE BUREAU DES INCENDIES AU SUJET DES RESTRICTIONS ET DES INSPECTIONS D’INSTALLATION DANS VOTRE VOISINAGE
Listed Room Heaters, Solid Fuel Type/ Appareil de Chauffage de Pièce, de Combustibles Solides
FOR USE WITH SOLID WOOD FUEL ONLY / POUR USAGE AVEC LE BOIS SEULEMENT
Serial No. / Numéro de Série
Manufactured for / Fabriqués pour:
LENNOX HEARTH PRODUCTS
1110 West Taft Avenue
Orange, CA 92865
US
Model / Modèle: CI 1000HT
Report No. / Numéro de Rapport 132-S-03-2
Tested To / Testé à: UL 1482, ULC-S627
"PREVENT HOUSE FIRES"
"PRÉVENTION DES FEUX DE MAISON"
Install and use only in accordancewithmanufacturer'sinstallationinstructionsand your local
building codes.
CAUTION: Special methodsare requiredwhenpassing chimneythrougha wallor ceiling, refer
to installationinstructionsandlocal buildingcodes. Donotpass chimneyconnectorthrougha
combustible surface. Do not connect this unit to a chimney flue serving another appliance.
Installez et utilisez en accord avec les instructions d’installation du fabricant et des codes locaux.
AVIS: Prenez des précautionsspéciales lorsque vous faites passer une cheminéeà travers un
mur ou un plafond, référez-vousaux instructions d’installationet aux codes locaux de la
construction.Ne pas faire passer le tuyaude cheminéeà travers une surface combustible.Ne
pas connecter cet appareil à un tuyau de cheminée servant un autre appareil.
NOTE: Replace glass only with 5mm ceramic. Operate with the doors closed.
NOTE: Remplacez la vitre avec une céramique de 5mm seulement.Opérez avec les porte fermée.
BACKWALL
ADJACENT WALL
Floor protectormust be a 1/2" minimum
thickness, non-combustiblematerial
(havingan equalor betterinsulatingvalue
(lower k Value) of k=.84 BTU/IntF Hr F.
It mustextendbeneathheater, andto the
front/sides/rear as indicated.
Le protecteurde plancherdoit être d'une
épaisseur minimumde 1/2", d'un matériel
incombustibleayant une valeur d'isolation
de k=.84 BTU/In Ft2 Hr F.
Il doit s'étendreen dessous de l'appareilet
au devant, aux côtés et à l'arrière de
l'appareil comme indiqué.
FLOOR PROTECTOR
MURARRIÈRE
MURADJACENT
PROTECTEUR DE PLANCHER
2
*8" (200mm)
0"
A
D
45°
C
B
5.2"
*8" (200mm)
5.2"
*8" (200mm)
*In Canada, requiredfloor protection
must be a 1.45" minimumthickness
extending18" (450mm)in front and 8"
(200mm) on all other sides of the
appliance.
F
*Au Canada, la protectionde sol nécessaire
doit avoir une épaisseur de minimum1.45”
et dépasser l’avant de l’appareil de 18”
(450mm) et le autres côtés de 8”(200mm).
E**
(450mm)
18"
Chimney &
Clearance Connector
Dimensions
Espaces
Libres
Cheminée
et Tuyau
Dimensions
Installation
A
B
C
D
E** F**
Installation
A
B
C
D
E** F**
U.S.
(in inches)
Residential
Residential
Standard Note: 1
27.50 27.00 27.00 24.00 18.00 19.00
21.50 27.00 19.00 18.00 18.00 11.00
Canada
(en mm)
Résidentielle Standard Note: 1
Résidentielle Réduits Note: 1, 2
698 686 686 610 457 483
546 686 483 457 457 279
Reduced
Note: 1, 2
** “E”dimension is measured to side of stove below the projection of outer top.
Note 1: 6 inch diameter, single wall, minimum24 MSG black or 25 MSG blued steel
connector pipe with factory-built chimney listed to either UL 103HT or ULC S629.
Note 2: Pipe shield for 6" connector with 1 inch clearance to pipe.
** Les dimension “E”est mesurées du côté du poêle en dessous de la projection
extérieure du haut du poéle.
Note 1: Le tuyau connecteur en acier noir de minimum 24 MSG ou en acier bleu de 25 MSG,de 6”
de diamètre,pour mur simple,avec cheminée faite en usine,enregistrée sous ULC S-629.
Note 2: Pour la buse de 6”, le protecteur doit être positionné à au minimum 1”de celle-ci.
CAUTION:
HOT WHILE IN OPERATION. DO NOT TOUCH.
CONTACT MAY CAUSE SKIN BURNS. KEEP CHILDREN, CLOTHING,
FURNISHINGS AND COMBUSTIBLE MATERIAL CONSIDERABLE
ATTENTION:
CHAUD LORS DE L’OPÉRATION. NE PAS TOUCHER. LE
CONTACT PEUT CAUSER DES BRÛLURES À LA PEAU. GARDEZ LES ENFANTS, LES
VÊTEMENTS, LES MEUBLES ET LES MATÉRIAUX COMBUSTIBLES LOIN DE L’ESPACE
DÉSIGNÉ DE L’APPAREIL. VOIR L’ÉTIQUETTE ET LES INSTRUCTIONS. NE PAS
SURCHAUFFER. SI L’APPAREIL DE CHAUFFAGE OU LE TUYAU DE CHEMINÉE
ROUGISSENT, VOUS SURCHAUFFEZ. INSPECTEZ ET NETTOYEZ LA CHEMINÉE ET LE
TUYAU CONNECTEUR FRÉQUEMMENT. SOUS CERTAINES CONDITIONS, IL SE PEUT QUE
LA CRÉOSOTE S’ACCUMULE RAPIDEMENT. N’ÉLEVEZ PAS LE FEU. BÂTISSEZ LE FEU DE BOIS
DIRECTEMENT SUR L’ÂTRE. NE PAS BRÛLER LORSQUE LES PORTE D’OUVERTURE EST OUVERTE.
LES PORTE D’OUVERTURE DOIT ÊTRE FERMÉE PENDANT L’USAGE EXCEPTÉ PENDANT QUE VOUS
AJOUTEZ DU FEU. OUVREZ LE TUYAU D’AIR AVANT D’OUVRIR LES PORTE D’OUVERTURE.
A
DISTANCE AWAY. SEE NAMEPLATE AND INSTRUCTIONS. DO NOT
OVERFIRE. IF HEATER OR CHIMNEY CONNECTOR GLOWS, YOU ARE
OVERFIRING. INSPECT AND CLEAN CHIMNEY AND CONNECTOR
FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE, CREOSOTE
BUILDUP MAY OCCUR RAPIDLY. DO NOT USE GRATE OR ELEVATE FIRE - BUILD
WOOD FIRE DIRECTLY ON HEARTH. DO NOT BURN WITH FEED DOORS OPEN. FEED
DOORS MUST BE CLOSED DURING FIRING EXCEPT WHEN ADDING FUEL. OPEN
COMBUSTION AIR CONTROL BEFORE OPENING FEED DOORS.
Date of Manufacture / Date de Fabrication
2006 2007 2008 Jan. Feb. Mar. Apr. May June July Aug. Sept. Oct. Nov. Dec.
U.S. ENVIRONMENTAL PROTECTION AGENCY
Certified to comply with July 1990 particulate emission standards.
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE
Made in Belgium by FDL
IGN P/N 775111M, Rev. A
32
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY/LISTING LABEL – Model CI2000HT
CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA
CONTACTEZ LE BUREAU DE LA CONSTRUCTION OU LE BUREAU DES INCENDIES AU SUJET DES RESTRICTIONS ET DES INSPECTIONS D’INSTALLATION DANS VOTRE VOISINAGE
Listed Room Heaters, Solid Fuel Type/ Appareil de Chauffage de Pièce, de Combustibles Solides
FOR USE WITH SOLID WOOD FUEL ONLY / POUR USAGE AVEC LE BOIS SEULEMENT
Serial No. / Numéro de Série
Manufactured for / Fabriqués pour:
LENNOX HEARTH PRODUCTS
1110 West Taft Avenue
Orange, CA 92865
US
Model / Modèle:
CI 2000HT
Report No. / Numéro de Rapport 132-S-05-2
Tested To / Testé à: UL 1482, ULC-S627
"PREVENT HOUSE FIRES"
"PRÉVENTION DES FEUX DE MAISON"
Installand use only in accordance with manufacturer'sinstallationinstructions and your local
Installez et utilisez en accord avec les instructions d’installation du fabricant et des codes locaux.
building codes.
AVIS: Prenez des précautions spécialeslorsque vous faites passer une cheminéeà travers un
mur ou un plafond, référez-vous aux instructions d’installationet aux codes locaux de la
construction. Ne pas faire passer le tuyau de cheminéeà travers une surface combustible.Ne
pas connecter cet appareil à un tuyau de cheminée servant un autre appareil.
CAUTION: Specialmethods arerequiredwhen passing chimneythrough a wallor ceiling,refer
to installationinstructions and localbuildingcodes.Do not pass chimneyconnector through a
combustible surface. Do not connect this unit to a chimney flue serving another appliance.
NOTE: Replace glass only with 5mm ceramic. Operate with the doors closed.
NOTE: Remplacez la vitre avec une céramique de 5mm seulement. Opérez avec les porte fermée.
Floor protector must be
a
1/2"
Le protecteur de plancher doit être d'une
FLOOR PROTECTOR
BACKWALL
ADJACENT WALL
MURADJACENT
minimumthickness, non-combustible
material(having an equal or better
insulating value (lower k Value) of
k=.84 BTU/In Ft2 Hr F.
épaisseur minimumde 1/2", d'un matériel
PROTECTEUR DE PLANCHER
MURARRIÈRE
incombustibleayant une valeur d'isolation
de k=.84 BTU/In Ft2 Hr F.
*8" (200mm)
0"
A
D
45°
C
Il doit s'étendre en dessous de l'appareilet
au devant, aux côtés et à l'arrière de
l'appareil comme indiqué.
G
H
It must extend beneath heater,and to
the front/sides/rear as indicated.
B
F
5"
*8" (200mm)
5"
*8" (200mm)
E**
*InCanada, required floor protection
must be 18” (450mm)in front and 8”
(200mm)on all other sides of the
appliance.
*Au Canada, la protection du plancher doit
s’étendrede 18” (450mm)en avant et de 8”
(200mm)sur tous les autres côtés de
l’appareil.
STOVE
POÊLE
(450mm)
18"
Chimney &
Installation Clearance Connector
Dimensions
E** F**
Espaces Cheminée
Libres et Tuyau
Dimensions
A
B
C
D
G
H
Installation
A
B
C
D
E** F**
G
H
U.S.
Residential Standard Note: 1
18.00 32.00 27.00 13.00 20.00 16.00 29.00 60.00
14.50 28.50 18.00 10.00 17.00 7.00 29.00 60.00
Canada
(en mm)
Résidentielle Standard Note: 1
457 813 686 330 508 406 737 1524
368 724 457 254 864 178 737 1524
(in inches) Residential Reduced Note: 2
Résidentielle Réduits
Résidentielle Alcôve
Note: 2
Residential Alcove
Note: 2,3 14.50 28.50 N/A 10.00 17.00 N/A 29.00 60.00
Note: 2,3 368 724 N/A 254 864 N/A 737 1524
** “E” dimension is measured to side of stove below the projection of outer top.
Note 1: 6 inch diameter,single wall,minimum 24 MSG black or 25 MSG blued steel
connector pipe with factory-built chimney listed to either UL 103HT or ULC S629.
Note 2: 6 inch diameterlisteddouble wallchimney connector or Type L vent pipe betweenthe
stove and chimney.
** Les dimension “E” est mesurées du côté du poêle en dessous de la projection
extérieure du haut du poéle.
Note 1: Le tuyau connecteur en acier noir de minimum 24 MSG ou en acier bleu de 25 MSG, de 6”
de diamètre, pour mur simple, avec cheminée faite en usine, enregistrée sous ULC S-629.
Note 2: Le tuyau connecteur de 6” de diamètre, pour mur double ou un connecteur de cheminée de
type L entre le poêle et la cheminée.
Note 3: Maximum alcove depth must be no more than 48” (1220mm).
Note 3: La profondeur maximum de l’alcove ne peut dépasser 48” (1220mm).
CAUTION:
HOT WHILE IN OPERATION. DO NOT TOUCH.
CONTACT MAY CAUSE SKIN BURNS. KEEP CHILDREN, CLOTHING,
FURNISHINGS AND COMBUSTIBLE MATERIAL CONSIDERABLE
ATTENTION:
CHAUD LORS DE L’OPÉRATION. NE PAS TOUCHER. LE
CONTACT PEUT CAUSER DES BRÛLURES À LA PEAU. GARDEZ LES ENFANTS, LES
VÊTEMENTS, LES MEUBLES ET LES MATÉRIAUX COMBUSTIBLES LOIN DE L’ESPACE
DÉSIGNÉ DE L’APPAREIL. VOIR L’ÉTIQUETTE ET LES INSTRUCTIONS. NE PAS
SURCHAUFFER. SI L’APPAREIL DE CHAUFFAGE OU LE TUYAU DE CHEMINÉE
ROUGISSENT, VOUS SURCHAUFFEZ. INSPECTEZ ET NETTOYEZ LA CHEMINÉE ET LE
TUYAU CONNECTEUR FRÉQUEMMENT. SOUS CERTAINES CONDITIONS, IL SE PEUT QUE
LA CRÉOSOTE S’ACCUMULE RAPIDEMENT. N’ÉLEVEZ PAS LE FEU. BÂTISSEZ LE FEU DE BOIS
DIRECTEMENT SUR L’ÂTRE. NE PAS BRÛLER LORSQUE LES PORTE D’OUVERTURE EST OUVERTE.
LES PORTE D’OUVERTURE DOIT ÊTRE FERMÉE PENDANT L’USAGE EXCEPTÉ PENDANT QUE VOUS
AJOUTEZ DU FEU. OUVREZ LE TUYAU D’AIR AVANT D’OUVRIR LES PORTE D’OUVERTURE.
A
DISTANCE AWAY. SEE NAMEPLATE AND INSTRUCTIONS. DO NOT
OVERFIRE. IF HEATER OR CHIMNEY CONNECTOR GLOWS, YOU ARE
OVERFIRING. INSPECT AND CLEAN CHIMNEY AND CONNECTOR
FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE, CREOSOTE
BUILDUP MAY OCCUR RAPIDLY. DO NOT USE GRATE OR ELEVATE FIRE - BUILD
WOOD FIRE DIRECTLY ON HEARTH. DO NOT BURN WITH FEED DOORS OPEN. FEED
DOORS MUST BE CLOSED DURING FIRING EXCEPT WHEN ADDING FUEL. OPEN
COMBUSTION AIR CONTROL BEFORE OPENING FEED DOORS.
Date of Manufacture / Date de Fabrication
2006 2007 2008 Jan. Feb. Mar. Apr. May June July Aug. Sept. Oct. Nov. Dec.
U.S. ENVIRONMENTAL PROTECTION AGENCY
Certified to comply with July 1990 particulate emission standards.
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE
Made in Belgium by FDL
IGN P/N 775112M, Rev. A
33
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE
Download from Www.Somanuals.com. All Manuals Search And Download.
EPA LABELS – CI1000HT and CI2000HT
34
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNERSHIP RECORDS
Dealer’s Name:
Dealer’s Address:
City:
Zip Code:
State:
Date Installed:
Date of Purchase:
Serial Number:
Notes:
SERVICE AND MAINTENANCE LOG
Service Service
Date Technician
Service
Description
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Normally, all parts should be ordered through your Lennox Hearth
Products distributor or dealer. Parts will be shipped at prevailing prices
at time of order.
WARRANTY
Your wood appliance is covered by a limited warranty (provided with
appliance). Please read the warranty to be familiar with its coverage.
When ordering repair parts, always give the following information:
Retain this manual. File it with your other documents for future refer-
ence.
1. The model number of the appliance.
2. The serial number of the appliance.
3. The part number.
4. The description of the part.
5. The quantity required.
PRODUCT REFERENCE INFORMATION
We recommend that you record the following important information
about your fireplace. Please contact your Lennox Hearth Products dealer
for any questions or concerns. For the number of your nearest Lennox
Hearth Products dealer, please call 1-800-9-Lennox.
6. The installation date of the appliance.
If you encounter any problems or have any questions concerning the
installation or application of this system, please contact your dealer.
REPLACEMENT PARTS
LENNOX HEARTH PRODUCTS
1110 West Taft Avenue
Orange, CA 92865
See Pages 24 to 30 for a complete replacement parts list. Use only parts
supplied from the manufacturer.
Your Stove's Model Number __________________________________________
Your Stove's Serial Number___________________________________________
The Date On Which Your Stove Was Installed _____________________________
Your Dealer's Name _________________________________________________
Lennox reserves the right to make changes at any time, without notice, in design, materi-
als, specifications, prices and also to discontinue colors, styles and products. Consult
your local distributor for fireplace code information.
Printed in U.S.A. © Lennox Hearth Products 2002
P/N 775,080M Rev. G 09/2007
1110 West Taft Avenue • Orange, CA 92865
36
Download from Www.Somanuals.com. All Manuals Search And Download.
|