Lennox Hearth Indoor Fireplace CPF 38 User Manual

HOMEOWNER'S CARE AND  
OPERATION INSTRUCTIONS  
MERIT® SERIES  
36" Multi-View Wood Burning Fireplaces  
P/N 875,040M REV. N/C 01/2007  
MODELS  
CST-38  
CPF-38  
CR-3835R  
CR-3835L  
The information contained in this manual applies to all model fireplaces  
identified on this page. This information will help you obtain safe and  
dependable service from your fireplace system. Keep this document in a  
safe place for future reference.  
Before you start your first fire, read this Care and Operations Manual  
carefully to be sure you understand your fireplace system completely.  
Failuretofollowthesesuggestionscouldresultinhazardousoperationor  
fireplacemalfunction, creatingaseriouspotentialforpersonalinjuryand/  
or property damage.  
If you have any questions regarding the safe use or operation of your  
fireplace, contact your local distributor or your contractor/builder.  
Most chimney systems will require onsite completion after placement of  
the manufactured home.  
OTL Report No. 116-F-20-4  
RETAIN THESE INSTRUCTIONS  
FOR FUTURE REFERENCE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. As a general rule, denser woods contain  
morepotentialheatperpound.Mostsoftwoods  
offer moderate heat value per pound.  
The higher the density, the more potential heat  
output. A standard cord has a volume of 128  
cubic feet. This figure also includes the air  
space between and around the wood. The ac-  
tual volume in a standard cord is between 60  
and 100 cubic feet; depending on how tightly  
the wood is packed.  
Wood Fuel Pointers  
Wood is a wonderful renewable fuel source.  
Normallyitburnsclean,leavingonlyaminimum  
of waste ash, provides comforting heat and can  
provide a variety of aromas and visual images.  
3. Differentwoodsvarywidelyinflameheights,  
flame intensities, smoke characteristics and in  
sparking. Most hardwoods do not spark.  
Youwillwanttoknowwhichwoodsarebestfor  
use. Sometimes you may want a quick, short  
fire to offset a morning chill. Soft woods are  
preferable in this case. Other times you would  
want more slow burning and a uniform heat  
output. Hardwoods are preferable for this use.  
4. Most freshly cut green” wood will not burn  
wellandwillsmoke.Greenwoodcanbefrom10  
to 40 percent less efficient than air-dried sea-  
soned wood.  
Standard  
Cord of  
Wood  
8'  
5. Moisture and resin found inside unseasoned  
woodcellswillbuilduppressureunderheatand  
explode as sparks.  
The amount of heat available from the logs will  
beaboutequalonaweightbasis.However,logs  
aregenerallynotweighedsotheamountofheat  
will depend on:  
4'  
6. Most wood needs to be seasoned 9 to 12  
months to reduce the moisture content and  
producegoodsteadyfires.Whenmoisturecon-  
tent is reduced from 60 to 20%, the gain in heat  
potential is nearly 7%.  
4'  
1. The type of wood used.  
2. How dry it is.  
3. How many logs you put in.  
4. The size of the logs.  
Figure 1  
7. Proper storage of wood, especially during  
seasoning, is essential. We recommend that  
you:  
HARDWOODS  
DENSITY  
The last statement means that one big log  
weighing 10 pounds has as much heating po-  
tential as 10 pounds of twigs. However, air  
cannot get at the solid log to feed the fire so the  
solid log will burn slowly. While you would get  
the same amount of heat out of either fire, the  
smaller the pieces of wood and the more air  
space around them, the faster the fire will burn.  
Alser, Red  
Ash  
Aspen  
Basswood, American  
Beech, American  
Birch  
.41  
.49-.60  
.38-.39  
.37  
.64  
.55-.65  
.38  
a. Never store wood on the ground. This will  
causerottingandinsectinfiltration.Raisewood  
on flat rock or scrap wood.  
Butternut  
Cherry, Black  
Chestnut, American  
Cottonwood  
Elm  
Hackberry  
Hickory, Pecan  
Hickory, True  
Honey locust  
Locust, Black  
Magnolia  
Maple  
Oak, Red  
Oak, White  
Poplar  
Sassafras  
.50  
.43  
b. Stack wood loosely to allow air circulation.  
.34-.40  
.60.63  
.53  
.60.66  
.69-.75  
.66 (est.)  
.69  
.48-.50  
.48-.63  
.59-.67  
.64-.88  
.42  
.42  
.52  
.49  
.64 (est.)  
.50  
c. Store wood where it will not be excessively  
exposed to weather, such as under a tarp or  
under a roof.  
Disposal of ashes  
Ashes should be placed in a metal container  
with a tight fitting lid. The closed container of  
ashes should be placed on a non-combustible  
floor or on the ground, well away from all  
combustible materials, pending final disposal.  
Iftheashesaretobedisposedofbyburialinsoil  
or other wise locally dispersed, they should be  
retained in the closed container until all cinders  
have thoroughly cooled.  
d. Do not stack wood directly against the walls  
of your home.  
8. Be a knowledgeable wood buyer. There is a  
difference in cord sizes. A standard cord stack  
of logs is 4 ft. high by 8 ft. long by 4 ft. deep or  
the equivalent of this cubic footage. A face cord  
isthesameheightandlengthasastandardcord  
but the depth is only the length of the logs (12,  
18or24inches).Afacecordcancontainaslittle  
as 25% of the wood found in a standard cord.  
Sweet gum  
Sycamore, American  
Tanoak  
Tupelo  
Walnut, Black  
Willow, Black  
Softwood vs Hardwood  
Softwoods contain about 15 percent highly  
flammableresinwhichgeneratescreosotesoot  
in the chimney flue. Burning softwood exclu-  
sively may not be as desirable nor as safe as  
burning denser hardwoods. Many experienced  
fire-builders use small amounts of softwood  
kindling and newspaper in conjunction with  
startingafirewithsplithardwoodlogs.Hereare  
some guidelines to remember:  
.55  
.39  
If you buy by the ton, remember that wood  
becomes lighter as it dries. When buying green  
or wet wood, ask for some extra poundage to  
allow for the extra water you will be getting.  
SOFTWOODS  
DENSITY  
Bald cypress  
Cedar  
Douglas Fir  
Fir  
Hemlock  
Larch, Western  
Pine  
Redwood  
Spruce  
.46  
.31-.47  
.46-.50  
.32-.43  
.40-.45  
.52  
.39-.59  
.35-.40  
.35-.41  
.53  
9. When comparing woods of the same mois-  
ture content and same species, we find most  
woods have approximately the same heating  
potential per pound. However, most wood is  
sold by volume, not by weight. To determine  
the best heating source, look at the density of  
various wood types. (Density is the weight for  
a given size.)  
1. Softwoodsproducefastwarmingandshorter  
fires. Hardwoods burn less vigorously, have  
shorter flames and produce steady, glowing  
coals.  
Tamarack  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assumingthatyouarecomparingtwostandard  
cords of different species but the same volume  
and moisture content, the denser species will  
providemoreBTU’s.Thetableofwoodspecies/  
densities reveals more helpful guidelines.  
WARNING: THE CR SERIES FIREPLACES  
SHOULDBEOPERATEDWITHTHEDOORS  
FULLY OPEN OR FULLY CLOSED. IF THE  
DOORSARELEFTPARTIALLYOPEN, GAS  
AND FLAMES MAY BE DRAWN OUT OF  
THEOPENING, CREATINGRISKSOFBOTH  
FIRE AND SMOKE. REFER TO FIGURE 2  
FOR PROPER OPERATING CONDITIONS.  
STARTING A FIRE  
Both Sets of Glass Doors  
Fully Closed  
1. To start a fire in your fireplace properly, first  
check the operation of the flue damper.  
CPF Models  
The design of the flue damper assembly varies  
for some model fireplaces. For the standard  
corneropeningfireplaces(CRSeries)thedamper  
is activated by a center mounted handle. The  
damperisopenedbypullingthehandleforward.  
To close, the handle is pushed all the way to the  
backofthefirebox.ThedamperisNOTADJUST-  
ABLE between the open and closed position.  
Figure 4  
Care and Cleaning of Your Glass Doors  
Never clean the glass when the doors are hot.  
Do not use ammonia or ammonia based glass  
or household cleaner to clean the glass or the  
door frame. An ammonia based cleaner will  
damage the finish of your glass door.  
Glass Doors  
Fully Open or  
Fully Closed  
To open the damper on the CST and CPF  
fireplaces, push the center damper handle  
straight up. To close pull handle down.  
CR Series  
In most cases, a clean dampened towel fol-  
lowed by a dry towel will clean the glass. To  
removeanystubbornstainsfromtheglass,use  
a mild soap solution and a towel dampened  
with clean water and then dry with a clean dry  
towel.  
Figure 2  
2. The grate in the firebox should be centered  
on or over the bottom hearth so your fire can  
breath properly. Crumble and twist plenty of  
newspapers UNDER the grate and criss-cross  
some small dry kindling sticks on top of the  
paper or on the bottom of the grate.  
CAUTION:IFASMOKINGCONDITIONEXISTS,  
GLASS DOORS SHOULD BE CLOSED DURING  
FIREPLACE OPERATION.  
Glass Door Operating Safety  
Precautions and Instructions  
WARNING: THE CST AND CPF FIRE-  
PLACES SHOULD BE OPERATED WITH  
BOTH SETS OF GLASS DOORS FULLY  
CLOSED. IF THE DOORS ARE LEFT OPEN  
OR PARTIALLY CLOSED, GAS AND  
FLAME MAY BE DRAWN OUT OF THE  
FIREPLACE OPENING, CREATING RISKS  
OF BOTH FIRE AND SMOKE. REFER TO  
FIGURES 3 AND 4 FOR PROPER OPER-  
ATING CONDITIONS.  
3. Build a pyramid of three split logs (split will  
startmuchfaster).Arrangetheunevenwoodto  
provide plenty of air space between.  
The fire must always be confined within the  
boundaries of the fuel grate.  
The fireplace screens must always be closed  
whenever the fireplace is operated.  
4. Now, light the paper at both sides of the  
firebox.  
Neverslamtheglassdoorsinceitcouldcause  
the glass to break.  
5. Close the screens to prevent the escape of  
sparks and embers.  
Do not build excessively large or hot fires.  
Scorching or discoloring of the solid brass or  
plated brass trim could result.  
6. Close the damper only when your fire is  
completelyoutandashesarecold.Keepclosed  
whenfireplaceisnotinusetopreventunneces-  
sary loss of heated or cooled air.  
Extremetemperaturechangescancauseglass  
breakagedonotbuildahotfireandclosethe  
glass doors if the doors are cold.  
GLASS DOORS  
The required glass door enclosures come in  
two different styles; All-GlassTM Twin Pane  
andbi-folddesignwithtemperedglasspanes.  
Removal or modifications to the glass doors  
may void your warranty and cause a smoking  
condition.  
Ifthetemperedglasspanebecomesscratched  
or chipped, it creates a weakness in the glass  
whichcancausetheglasstobreakwhenheated.  
Replace the pane of glass by contacting your  
nearest dealer or distributor.  
Both Sets of Glass Doors  
Fully Closed  
CST Models  
Figure 3  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAUTION: GLASS AND METAL FRAMES GET  
HOTALWAYSUSEHANDLESTOOPENAND  
CLOSE THE DOORS.  
On the CR Series fireplaces, the control lever  
that operatestheoutsidecombustionair valve  
has been pre-installed on your fireplace. A  
coverplatehasbeenmountedoverthiscontrol  
lever only if the outside air kit has not been  
attached. The control lever is located on the  
closed end of the fireplace opening behind the  
screen. To open the air damper, turn the lever  
handle 1/2 turn counter clockwise (or until  
levercanbemovedupward),thenre-tightenat  
desired open position. To close damper, re-  
verse procedure (Figure 5 ).  
LINTEL EXTENSION  
These Merit Multi-Open Factory-Built  
Fireplaces were designed, tested and listed  
with an 18" (457 mm) high viewing area, floor  
to lintel. However, varying conditions such as  
altitude, climate, wood type, moisture content  
of fuel, dwelling design peculiarities, average  
ambient air pressure and humidity may effect  
the performance of this fireplace. If an unac-  
ceptable amount of smoking occurs while the  
doors are open, the adjustable lintel can be  
moved to correct the smoking condition.  
WARNING: CERTAIN MODEL FIRE-  
PLACES REQUIRE THAT THE GLASS  
DOORS BE CLOSED DURING OPERA-  
TION. BE AWARE THAT SAFETY GLASS  
IS UNPREDICTABLE WHEN HOT AND  
MAY BREAK, EXPELLING HOT GLASS  
INTO THE ROOM. ADVISE ALL FAMILY  
MEMBERS TO REMAIN WELL AWAY  
FROMTHEFIREPLACEWHENOPERAT-  
ING WITH DOORS CLOSED TO AVOID  
ANY POSSIBLE PERSONAL INJURY.  
The lintel extension can be lowered a maxi-  
mum of 2" (51 mm) using a predrilled hole  
located at the top of the lintel extension. To  
lower the lintel extension 1" (25 mm), drill a  
1/8" (3 mm) hole where the dimple is located.  
(See Figure 7.)  
COMBUSTION AIR  
A proper amount of combustion air is impor-  
tant for your fireplace. Fireplaces consume  
large amounts of oxygen. It is important to  
allow an adequate supply of air. If the fireplace  
is not equipped with an outside air kit, it may  
not obtain sufficient amounts of combustion  
air from inside the house or structure in which  
it is installed. Therefore, the fire may draw  
from an outside air source and pull air in  
through the chimney. This may cause smoke  
spillage into the room.  
Control  
Lever  
TolowerthelintelextensiononModelCST-38,  
remove the two screws from both ends of the  
lintel extension (located behind the screen  
assembly). Slidethelintelextensiondownand  
align the desired holes in the lintel extension  
with the holes in the lintel frame. Reattach  
using the screws previously removed. Repeat  
this procedure for the lintel extension on the  
opposite side of the fireplace. (Figure 7 )  
Figure 5  
On the Merit Series fireplaces, the control  
lever that operates the outside combustion air  
valve is located on one lower side behind the  
screen panel. Push the lever all the way in to  
open the air valve and pull the lever all the way  
out to close the air valve (Figure 6 ).  
Smokespillageoftenoccurswhenafireisfirst  
started,untilthefireplaceandthechimneyhas  
had the opportunity to come up to tempera-  
ture” and to begin to function normally. If  
smoke spillage problems persist, a window  
may be opened just a crack to allow the proper  
flow of combustion air to the fireplace.  
Front  
Frame  
Open  
Lintel  
Frame  
If your fireplace is equipped with an outside  
combustionairkit,keepopenatalltimeswhen  
fire is burning and close when fire is out to  
prevent cold air intrusion.  
Original Position  
Closed  
Lowest  
Dimple  
Position  
2" (51 mm)  
Lintel  
Extension  
Combustion Air Control  
The operation and location of the outside air  
controllevervariestosomeextentondifferent  
fireplace models.  
Figure 7  
Figure 6  
On Model CPF-38 the two (2) side lintel exten-  
sionsareweldedtotheendlintelextension.The  
lintel extension lowers similarly to the CST-38  
lintel extension. However, to prevent the end  
lintel extension from being misshaped, follow  
the following steps while referring to Figure 7.  
The outside air damper should be kept closed  
on all fireplaces except when the fireplace is in  
operation. If there is no heat present in the  
firebox, the air damper should be closed at  
night before retiring to prevent intrusion of  
outside air into the home.  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Look up from inside the fireplace (damper  
open) to see any obstructions in the lower flue  
area.Ifpresent,shutthedamperandglassdoors  
(if installed) to seal the firebox and contain any  
soot that might fall. If your do not have glass  
doors installed, a damp sheet covering the fire-  
place opening and sealed with masking tape will  
do. Then clean the flue from the top down (if an  
offset system, clean per Step 2) using a proper  
size chimney brush with flexible pole sections.  
Don’topenthedoorsorremovethesheetuntilall  
soot has settled. Vacuum, don’t sweep.  
1. Remove the two (2) screws from one of the  
sidelintelextension, leavingthelintelextension  
on the other side attached to the lintel frame.  
Onlylowertheendofthelintelextensionclosest  
to the closed end (refractory wall) of the CPF-  
38. Aligning the desired holes in the lintel  
extension with the holes in the lintel frame and  
reattach using one (1) of the screws previously  
removed.  
If conditions 1, 2 or 3 occur, the refractory  
shouldbereplaced.Forminordefects,repairas  
noted above.  
MAINTENANCE GUIDELINES  
Your fireplace is designed to operate trouble-  
freewithminimummaintenance.However,like  
any fine appliance, it deserves and requires  
some housekeeping attention.  
2. Remove the two (2) screws from the lintel  
extension on the other side of the fireplace.  
Lower the whole lintel extension to the desired  
holes and reattach using the screws just re-  
moved.  
Your fireplace will perform better – and cer-  
tainly look more attractive to family and friends  
ifitiscleanedbeforeeachuse.Beforethefirst  
seasonaluseinAutumnandafterthelastfirein  
Spring, it is important to inspect the fireplace  
system carefully. We recommend at least two  
complete fireplace inspections a year.  
4. Check the metal flashing and seals around  
yourchimney.Sealanycracksorloosenailhead  
openings to prevent roof leaks.  
3. On the lintel extension first lowered, realign  
the holes as necessary then insert and tighten  
the remaining screw.  
5. Clean the firebox thoroughly by using a soft  
brush or equivalent.  
Before Each Use  
WARNING: CONTINUED OVER FIRING  
CAN PERMANENTLY DAMAGE YOUR  
FIREPLACE SYSTEM. SOME EXAMPLES  
OF OVERFIRING ARE:  
REFRACTORIES  
1. Clean the firebox of excessive ashes. Some  
owners prefer to leave a small layer to insulate  
the cold refractory below the grate which helps  
fire starting.  
All fireboxes contain a furnace refractory floor.  
Some models also have refractory sides and  
backs. These refractories are reinforced with  
steel, but can be broken by improper use.  
Dropping logs on the bottom refractory and  
building fires directly against the refractories  
can cause premature burnout of these compo-  
nents. It may easily be repaired or replaced at  
costs far below repair and maintenance for  
masonry fireplaces.  
• BURNING QUANTITIES OF SCRAP  
LUMBER, PINEBRANCHES, PAPEROR  
CARDBOARD BOXES WHICH EXCEED  
THE VOLUME OF THE NORMAL LOG  
FIRE.  
If your particular model fireplace has a factory  
supplied grate attached, it is permissible to  
remove the grate for cleaning; however, the  
grate must be re-attached to the fireplace be-  
fore the next burn.  
• BURNING TRASH, CHEMICALS OR  
CHEMICALLY TREATED COMBUS-  
TIBLES.  
2. Keepthefireplacescreenscleansocombus-  
tion air flows freely.  
Proper care and burn-in” of the firebox will  
prolongtheperiodofenjoymentwithoutexten-  
sive maintenance. For the first few uses, build  
smallfiresnotroaringinfernos.Thematerials  
used in the refractories contain and absorb  
moisture. It is important to cure” the refracto-  
ries by building only modest fires.  
Creosote Formation and Removal  
3. Spotcheckthebrick-likerefractoryforsmall  
cracks. Heat from the fire expands it slightly.  
When it cools, it contracts.  
Whenwoodisburnedslowly,itproducestarand  
other organic vapors, which combine with ex-  
pelled moisture to form creosote. The creosote  
vapors condense in the relatively cool chimney  
flue of a slow-burning fire. As a result, creosote  
residue accumulates on the flue lining. Creosote  
makes an extremely hot fire when ignited.  
Twice A Year Check-Up  
Undernormalusage, itisexpectedthathairline  
cracks will appear in the refractory surface.  
These hairline cracks do not affect the safe  
operation of the fireplace.  
Normally,twiceayear,youshouldinspectyour  
fireplace following this list:  
1. Inspect the opening in your chimney top and  
remove any debris that could clog it. The cap is  
usually held in place by four (4) screws, which  
remove easily for checking or cleaning the full  
length of the flue from above. Remove the  
chimney top while wearing gloves to guard  
against any sharp metal edges.  
Thechimneyshouldbeinspectedatleasttwice  
yearly during the heating season to determine  
if a creosote build-up has occurred.  
Refractories should be replaced when:  
1. The crack opens more than 1/4" (19 mm).  
If creosote has accumulated, it should be re-  
moved to reduce the risk of a chimney fire.  
2. Pitting in the surface is extensive and pits  
become deeper than 3/16" (4.76 mm).  
2. Inspect the entire flue from the top down for  
obstructions such as birds nests, leaves, etc.  
This may be done by using a flexible handled  
chimney cleaning brush. If the chimney con-  
tainsoffset/returnelbows;asoftbrushcleaning  
from the top down to any elbow and then from  
the firebox up to the offset/return section is the  
proper method. The beam from a powerful  
flashlight will help in this inspection.  
If creosote build-up is found, do not use  
chemical chimneycleanersthat arepouredon  
a hot fire. The manufacturer considers them  
dangerousandtheygenerallyonlyworkonthe  
flue section nearest the fire, leaving the rest of  
theflueunaffected. Itisbesttotakethetimeto  
clean the flue as previously described or have  
thechimneyprofessionallycleanedbyaquali-  
fied chimney sweep.  
3. Anypieceofrefractorylargerthan2"(51 mm)  
in radius and 3/16" deep becomes dislodged.  
If your refractory has a crack less than 1/4"  
(19 mm) in width, a simple Refractory Patch  
Kit, Model RPK, can easily be used to fill the  
crack and repair the refractory.  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ACCESSORIES AND COMPONENTS  
Less Than 10'  
2' Min.  
2' Min.  
10'  
3' Min.  
3' Min.  
Figure 8  
12M07  
12M08  
12M09  
36 ABF  
36 ABF-BB  
36 ABF-BS  
All-GlassTM  
Bi-Fold Doors  
6. Is a vent fan, exhaust hood or central  
heating/cooling system stealing combustion  
air from your fireplace? If their volume is high  
enough, this can cause negative pressure and  
an unwanted downdraft – and smoking.  
TROUBLE SHOOTING  
No Smoking Allowed  
Aluminum Doors  
Your new fireplace is designed not to smoke if  
properlyinstalledandoperatedperourinstruc-  
tions. If you do experience a problem, here are  
several things to check:  
Your fireplace can be fitted with beautiful  
aluminum doors. Model ABF doors are avail-  
able for use with these fireplace. Doors are  
easily fitted to the fireplace opening. Model  
ABF doors come with standard black finish.  
Model ABF-BB doors have a beautiful bright  
brass finish.  
7. Is your wood fuel too wet or unseasoned?  
Or does it contain some chemical substance  
that causes sputtering, smoking and toxic  
fumes?  
1. Remember – always check to ensure your  
flue damper is in the open position before  
lighting a fire!  
8. Figure 8 illustrates the correct height of  
your chimney top. It is unlikely that your  
installation does not adhere to the installation  
instructions.However,ifnotcorrect,youcould  
experienceanunusualdowndraft. Usually, the  
bestsolutionistoincreasethechimneyheight.  
This may also be necessary if nearby trees,  
adjoining roof lines or a hill is causing a  
downdraft condition.  
2. When lighting your fire, a little smoke may  
escape into the room – more likely if the chim-  
ney is cold. To correct this, hold a lighted  
newspaper up inside the firebox near the open  
flue damper. This will turn around any down-  
draft and clear the flue of cold air. As your log  
fireburnsbelow,theupdraftwillimproveasthe  
chimney heats up.  
To ensure warranty and to prevent a potential  
fire hazard, do not use any other doors on  
these appliances.  
9. Remember, your fireplace has been de-  
signed as a supplemental heating device only,  
it is not intended to heat your entire home.  
3. Is your fire too far forward? Move it toward  
the back with your poker. Keep the fire well  
within the confines of your fuel grate.  
ENJOY YOUR FIREPLACE  
4. Keep your fire up on the grate and the refrac-  
tory below free of excessive ashes. The fire  
needs plenty of air movement around the logs.  
If you encounter any problems or have any  
questions regarding the installation of op-  
eration of your fireplace system, contact  
your distributor. For your nearest distributor  
contact:  
5. If smoking occurs an hour or two after  
lighting the fire, perhaps your well-insulated  
house is too airtight and there is scarcely any  
way for replacement air to enter and feed the  
fire.Checktoseeifyouroutsidecombustionair  
kit(ifinstalled)isopen.Checkoutsidetoensure  
noobstructionsareinfrontofexteriorairentry.  
Open a window slightly, open doors to one or  
two rooms and see if this stops the smoking.  
All-GlassTM  
Twin Pane Doors  
12M44  
38TBA-BB  
LENNOX HEARTH PRODUCTS  
1110 West Taft Avenue  
Orange, CA 92865  
Twin Pane Doors  
Your fireplace can be fitted with attractive  
Twin Pane doors. Model TBA doors are avail-  
able for use with these fireplace. Twin Pane  
doors are easily fitted to the fireplace opening.  
Model TBA-BB doors have a beautiful bright  
brass finish.  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
ACCESSORIES AND COMPONENTS  
REPLACEMENT PARTS  
CR-3835L  
Part No.  
CR-3835R  
Part No.  
DESCRIPTION  
Fireplace Assembly  
Grate  
H4403  
H4006  
H4412  
H4413  
H4416  
H4417  
H4536  
H0631  
90L73  
H4403  
H4006  
H4412  
H4413  
H4416  
H4417  
H4536  
H0632  
90L73  
Grate Bracket Holder  
Screen  
Side Screen (Corner Open Only)  
Screen Rod  
All-GlassTM  
Aluminum End Panel  
12M15  
12M16  
38AEP  
38AEP-BB  
Side Rod (Corner Open Only)  
Refractory Clip/Retainer Rear  
Refractory Kit  
Aluminum End Panel  
Your CPF-38 fireplace can be fitted with a  
unique aluminum end panel. Model AEP end  
panels are available for use with these fire-  
place. End panels are easily fitted to the fire-  
place opening. Model AEP end panels come  
with standard black finish. Model AEP-BB end  
panels have a beautiful bright brass finish.  
Touch Up Paint  
CST-38  
Part No.  
CPF-38  
Part No.  
DESCRIPTION  
Fireplace Assembly  
Grate  
H4404  
H4528  
H4411  
H3994  
H4538  
H4537  
H0648  
90L73  
H4404  
H4528  
H4411  
H3994  
H4538  
N/A  
Door Track  
Screens  
Screen Rod  
Refractory Clip, Right  
Refractory Clip, Left  
Refractory Kit  
Touch Up Paint  
H0649  
90L73  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE  
The manufacturer reserves the right to make changes at any time, without notice, in design,  
materials, specifications, prices and also to discontinue colors, styles and products.  
Consult your local distributor for fireplace code information.  
Printed in U.S.A. © 2007 by LENNOX HEARTH PRODUCTS  
1110 West Taft Avenue  
Orange, CA 92865  
P/N 875,040M REV. N/C 01/2007  
Download from Www.Somanuals.com. All Manuals Search And Download.  

LG Electronics Cell Phone AS740 User Manual
LG Electronics Stereo System LH E922PB User Manual
Mackie Musical Toy Instrument 1604 User Manual
Magnasonic MP3 Docking Station MiDK101 User Manual
Maretron GPS Receiver GPS200 User Manual
Mark Feldstein Assoc Home Theater System sp1790jk User Manual
Maytag Washer W10254495A User Manual
McCulloch Snow Blower 96192004101 User Manual
Meade Binoculars CV 4 8 x 30 User Manual
Microsoft Projector CP D31N User Manual