Leica Laser Level 763495 User Manual

Leica DISTO^™D2

The original laser distance meter

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual

Intended Use

Permitted uses

English

•

Measuring distances

Congratulations on the purchase of your

Leica DISTO™ D2.

Computing functions, e.g. areas and volumes

The safety instructions and the user

manual should be read through

carefully before you use the

Adverse uses

•

Using the instrument without instructions

Using outside the stated limits

product for the first time. The

person responsible for the product must ensure that

all users understand these directions and adhere to

them.

Deactivation of safety systems and removal of

explanatory and hazard labels

•

Opening of the equipment by using tools (screw-

drivers etc.)

Carrying out modification or conversion of the

product

Use of accessories from other manufacturers

without the express approval of Leica Geosys-

tems.

Symbols used in this manual

The symbols used have the following meaning:

WARNING

Indicates a potentially hazardous situation or

an unintended use which, if not avoided, could result

in death or serious injury.

•

Deliberate or irresponsible behaviour on scaf-

folding, when using ladders, when measuring

near machines which are running, or near parts of

machines or installations which are unprotected

Aiming directly into the sun

Deliberate dazzling of third parties; even in the

dark

CAUTION:

Indicates a potentially hazardous situation or

an unintended use which, if not avoided, may result

in minor injury and/or in appreciable material, finan-

cial and environmental damage.

•

Important paragraphs which must be adhered

to in practice, as they enable the product to be used

in a technically correct and efficient manner.

)

•

Inadequate safeguards at the surveying site (e.g

when measuring on roads, construction sites,

etc.)

Leica DISTO™ D2 762202b gb

Symbols used in this manual

Download from Www.Somanuals.com. All Manuals Search And Download.

ance with the instructions. This person is also

accountable for the deployment of personnel and for

their training and for the safety of the equipment

when in use.The person in charge of the product has

the following duties:

Limits of use

Also see section "Technical data".

)

The Leica DISTO™ is designed for use in areas perma-

nently habitable by humans, do not use the product

in explosion hazardous areas or in aggressive envi-

ronments.

•

To understand the safety instructions on the

product and the instructions in the user manual.

To be familiar with local safety regulations

relating to accident prevention.

To inform Leica Geosystems immediately if the

equipment becomes unsafe.

Responsibilities

Responsibilities of the manufacturer of the orig-

inal equipment Leica Geosystems AG, CH-9435

Heerbrugg (for short Leica Geosystems):

Leica Geosystems is responsible for supplying the

product, including the User Manual and original

accessories, in a completely safe condition.

(Additional language versions can be found at:

www.disto.com)

Overview

Keyboard

See drawing {A}:

ON/DIST (ON/MEAS) - button

PLUS [+] - button

FUNCTION - button

REFERENCE - button

CLEAR/OFF - button

HISTORICAL MEMORY/TIMER - button

ILLUMINATION/UNITS - button

MINUS [-] - button

Responsibilities of the manufacturer of non-

Leica accessories:

The manufacturers of non-Leica accessories for the

Leica DISTO™ are responsible for developing, imple-

menting and communicating safety concepts for their

products. They are also responsible for the effective-

ness of these safety concepts in combination with

the Leica Geosystems equipment.

Responsibilities of the person in charge of the

instrument:

WARNING

The person responsible for the instrument

must ensure that the equipment is used in accord-

Leica DISTO™ D2 762202b gb

Download from Www.Somanuals.com. All Manuals Search And Download.

Overview

Display

Operation

See drawing {B}

Laser "ON"

Reference (front/rear/end piece)

Pythagoras

Measuring Conditions

Range

Timer (self-triggering)

Historical memory

Area/volume

Range is limited to 60 m.

At night or dusk and if the target is in shadow the

measuring range without target plate is increased.

Use a target plate to increase the measurement

range during daylight, or if the target has poor reflec-

tion properties!

Battery status

Units with exponents (²/³)

Intermediate line 2

10 Intermediate line 1

11 Main line

Target Surfaces

12 min / max display

13 Info symbol

CAUTION:

Measuring errors can occur when measuring

toward colourless liquids (e.g. water) or dust free

glass, Styrofoam or similar semi-permeable surfaces.

Aiming at high gloss surfaces may deflect the laser-

beam and lead to measurement errors.

Start up

Inserting / Replacing Batteries

Remove battery compartment lid.

See drawing {C}.

Hazards of Use

•

Insert batteries, observing correct polarity.

Close the battery compartment.

Replace the batteries when the symbol

permanently in the display.

CAUTION:

Watch out for erroneous distance measure-

flashes

ments if the instrument is defective or if it has been

dropped or has been misused or modified.

Only use alkaline batteries.

)

Precautions:

Carry out periodic test measurements.

Particularly after the instrument has been subject to

If the instrument will not be used for a long

time, remove the batteries as a protection against

corrosion.

)

Leica DISTO™ D2 762202b gb

Start up

Download from Www.Somanuals.com. All Manuals Search And Download.

abnormal use, and before, during and after important

measurements.

Make sure the Leica DISTO™ optic is kept clean and

that there is no mechanical damage to the bumpers.

Setting the instrument

Press long until the desired unit is displayed.

Possible units:

CAUTION:

Distance

Area

Volume

0.000 m³

In using the instrument for distance measure-

0.000 m²

0.00 ft²

0.000 m

ments or for positioning moving objects (e.g. cranes,

building equipment, platforms, etc.) unforeseen

events may cause erroneous measurements.

0'0'' ¹/₁₆

0 in ¹/₁₆

0.00 ft

0.0 ft³

Precautions:

Only use this product as a measuring sensor, not as

a control device. Your system must be configured and

operated in such a way, that in case of an erroneous

measurement, malfunction of the device or power

failure due to installed safety measures (e.g. safety

limit switch), it is assured that no damage will occur.

CLEAR-Key

1x briefly: the last action is cancelled.

Illumination

1x briefly: the display illumination is switched on

or off.

Switching on/off

1x briefly: the instrument and the laser are

switched on.

Reference Setting

Default reference setting is from the rear of the

instrument.

The instrument can be set for the following measure-

ments:

The display shows the battery symbol

the next button is pressed.

until

Pressing this button for longer switches the

instrument off.

•

To measure from an edge (see drawing {D}), fold

out the stop bracket until it snaps in for the first

time. See drawing {E}.

The instrument switches off automatically after

three minutes of inactivity.

•

To measure out of a corner (see drawing {D }),

fold out the stop bracket until it snaps in, push

Leica DISTO™ D2 762202b gb

Operation

Download from Www.Somanuals.com. All Manuals Search And Download.

the stop bracket with a little force to the right

side; the stop bracket can now be completely

unfolded. See drawing {E}.

The result is displayed immediately.

Continuous measurement

Distances can be measured with this function

1x long: a "beep" is sounded.A continuous

measurement is started.

CAUTION:

Make sure that when measuring from the

unfolded endpiece, the measuring reference is set to

"End piece"!

1x briefly: the continuous measurement is

stopped.

1x briefly: the next measurement is taken from

the front edge.

The last measured value is displayed in the summary

line.

2x briefly: the measurement is taken from the

unfolded end piece.

After one measurement, the reference returns auto-

matically to the default setting (rear reference).

Minimum-/Maximum-Measuring

This function enables determining the minimum or

maximum distance from a specific measuring point,

e.g. the determination of room diagonals (maximum

value) or horizontal distance (minimum value).

1x long: the measurements are taken with the

front as reference until a new measuring refer-

ence is set

Switching on continuous measurement (see above).

The corresponding maximum and minimum values are

displayed.

2x long: the measurements are taken from the

unfolded end piece until a new measuring refer-

ence is set.

See drawing {F}.

Functions

Measuring

Addition / Subtraction

Distance Measurement.

Single Distance Measurement

1x briefly: the next measurement is added to

the previous one.

1x briefly: the laser is activated.

1x briefly: a distance measurement is taken.

Leica DISTO™ D2 762202b gb

Measuring

Download from Www.Somanuals.com. All Manuals Search And Download.

1x briefly: the next measurement is subtracted

from the previous one.

The result of the second area measurement, "+"

flashes.

1x briefly: confirms the addition; the added area

results are displayed in the summary row.

Repeat this procedure for as many times as required.

The result is displayed in the summary row, the previ-

ously measured value is displayed in intermediate line

2, the value to be added in intermediate line 1.

Volume function

1x briefly: the last step is cancelled.

2x briefly: the

symbol is displayed.

1x briefly: takes first distance measurement

(e.g. length)

Area function

1x briefly: The

symbol is displayed.

1x briefly: takes second distance measurement

(e.g. width)

1x briefly: takes first distance measurement

(e.g. length)

The result of the area measurement from the values

already measured is displayed in the summary row.

1x briefly: takes second distance measurement

(e.g. width)

1x briefly: takes the third distance measure-

ment (e.g. height). The value is displayed in

intermediate line 1.

The result of the area measurement is displayed in

the summary row, the individually measured values

are displayed in intermediate lines 1 and 2.

The result of the area measurement is displayed in

the summary row, the two previously measured

values in intermediate lines 1 and 2.

Adding and subtracting areas

Calling up the area function and measuring areas.

Press

Indirect Measurement

The instrument can measure distances with the

Pythagorean method. This procedure facilitates in

measuring distances that are difficult to access.

1x briefly: takes first distance measurement

(e.g. length)

1x briefly: takes second distance measurement

(e.g. width)

Adhere to the prescribed sequence of meas-

)

urements:

Leica DISTO™ D2 762202b gb

Functions

Download from Www.Somanuals.com. All Manuals Search And Download.

•

All target points must be vertical or horizontal on

the surface of the wall.

The best results are achieved when the intrument

is rotated around a fixed point (e.g. the stop

bracket is fully extended and the instrument is

placed against a wall).

To take the measurement, the minimum/

maximum function can be called up. The minimum

value is used for measurements that must be at

right-angles to the target; the maximum distance

is used for all other measurements.

measuring a distance, maximum or minimum contin-

uous measuring is activated.

Indirect measurement - determining a

distance using 3 auxilliary measurements

See drawing {H}

•

4x briefly: the

symbol is displayed.

The distance to be measured flashes in the symbol.

1x briefly: takes a distance measuement

The second distance to be measured flashes in the

symbol

Make sure that the first measurement and the

)

distance to be measured are at right angles. Use the

1x briefly: takes a horizontal measurement.

The third distance to be measured flashes in the

symbol

minimum/maximum function.

Indirect measurement - determining a

distance using 2 auxilliary measurements

1x briefly: takes a measurement of the distance

See drawing {G}

The result of the function is displayed in the summary

row.

3x briefly: the

symbol is displayed.

The distance to be measured flashes in the symbol.

1x briefly: takes a measurement of the distance

If the

button is pressed for along time while

measuring a distance, maximum or minimum contin-

uous measuring is activated.

The second distance to be measured flashes in the

symbol

Stake out function

This function is helpful when staking out equal

distances, e.g in the erection of wooden substruc-

tures. See drawing {I}

1x briefly: takes a measurement of the hori-

zontal distance

The result of the function is displayed in the summary

row.

5x briefly: the

symbol is displayed.

If the

button is pressed for along time while

A value is displayed in the summary row (default

Leica DISTO™ D2 762202b gb

Download from Www.Somanuals.com. All Manuals Search And Download.

Functions

value 1.000 m). This value can be adjusted to the

desired stake out distance.

Using stored values in functions

Using added distances in area functions (e.g. wall

surfaces or painters):

Adding distances (see additions / subtractions)

Call up area function to e.g. measure the height

of a room.

The value is increased.

The value is reduced.

Holding the button down accelerates the speed at

which the value changes.

1x briefly: starts continuous measurement.

1x briefly: calls up the historical memory and to

possibly search for the correct value.

In intermediate line 1, the set distance or the next

appropriate multiple thereof is displayed.

In the summary row, the distance to the next appro-

priate stake out point is displayed.

When approaching a stakeout point (to less than

0,10 m), the instrument starts to beep. When the

point is reached, the beep sound changes and inter-

mediate line 1 starts to flash.

1x long: the value is entered into the function

and the result of the function (e.g. area) is

displayed.

Timer (self-triggering)

1x briefly: distance measurement is interrupted

and the instrument switches back to individual

distance measuring mode.

1x long: The

symbol is displayed.

The timer is preset to 5 seconds.

The value is increased.

The value is reduced.

Historical memory

1x briefly: the

symbol and the last measured

Holding the buttons down increases the rate of

change of the values.

value are displayed.

The countdown starts automatically (if the laser is

activated) and then triggers the measurement.

Use the "+" or "-" buttons to navigate through the

last 10 values. The values can also be used in func-

tions.

Leica DISTO™ D2 762202b gb

Functions

Download from Www.Somanuals.com. All Manuals Search And Download.

Cause

Correction

Switching off the beep

258

Outside of the range Select measurement

Press and hold simultaneously for 5

of measurement

distance within the

seconds:

range of measurement

Error

Cause

Error Hardware error

Correction

The beep is switched off.

To reactivate it, press and hold for 5 seconds.

Should this message

remain active after

switching the instru-

ment off and on several

times, please contact

the dealerhip.

Appendix

Display Notices

All display notices are either displayed with

"Error". The following errors can be corrected.

Technical Specifications

Range

0.05 m to 60 m*

Measuring accuracy (2

σ)

typically 1.5 mm**

Cause

Correction

Smallest unit displayed

Laser class

Laser type

1 mm

635 nm, < 1 mW

204

252

Calculation error

Repeat procedure

Let device cool down.

Temperature too

high

253

255

Temperature too

low

Warm device up

Protection against

IP 54, dust-proof,

splashes and dust

splash-proof

Received signal too Use a target plate

Autom. power off:

Laser

weak, time for a

after 60 s

measurement too

Instrument

after 180 s

long.

Illumination

Folding out endpiece

256

257

Received signal too Use target plate (gray

strong

side)

Faulty measure-

ment, too much

background light

Use target plate (brown

Battery life,

up to

side)

Type 2 x AAA

5 000 measurements

Dimension

Weight

111 x 43 x 23 mm

90 g

Leica DISTO™ D2 762202b gb

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Temperature range:

Storage

Laser classification

-25°C to +70°C

0°C to +40°C

The Leica DISTO™ produces a visible laser beam

which emerges from the front of the instrument.

See drawing {K}.

Operation

* Use a target plate to increase the measurement range

during daylight or if the target has poor reflection properties!

** in favourable conditions (good target surface properties,

room temperature) up to 10 m. In unfavourable conditions,

such as intense sunshine, poorly reflecting target surface or

high temperature variations, the deviation over distances

above 10 m can increase by 0.15 mm/m.

The product is a Class 2 Laser Product in accordance

with:

•

IEC60825-1 : 2007 "Radiation safety of laser

products"

Class 2 Laser Products:

Electromagnetic Compatibility

(EMC)

The term "electromagnetic compatibility" is taken to

mean the capability of the product to function

smoothly in an environment where electromagnetic

radiation and electrostatic discharges are present,

and without causing electromagnetic interference to

other equipment.

Do not stare into the beam or direct it unnecessarily

at other persons. Eye protection is normally afforded

by aversion responses including the blink reflex.

WARNING

Looking directly into the laser beam with

optical aids (e.g. binoculars, telescopes) can be

hazardous.

Precautions:

Do not look directly into the beam with optical aids.

WARNING

The Leica DISTO™ conforms to the most strin-

CAUTION:

gent requirements of the relevant standards and

regulations.

Looking into the laser beam may be hazardous

to the eyes.

Yet. the possibility of the product causing interfer-

ence in other equipment cannot be fully excluded.

Precautions:

Do not stare into beam. Do not look into the laser

beam. Make sure the laser is aimed above or below

eye level (particularly with fixed installations, in

machines, etc.).

Leica DISTO™ D2 762202b gb

Appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

* To receive the three year warranty, the product must be

registered on our website www.disto.com within eight

weeks of the purchase date. If the product is not registered,

a two year warranty applies.

Labelling

Laser Radiation

Do not stare into the beam

Disposal

Laser class 2

acc. IEC 60825-1:2007

CAUTION:

Maximum radiant power *: <1mW

Emitted wavelength:

620-690nm

Flat batteries must not be disposed of with

Beam divergence 0.16 x 0.6 mrad

-9

Impulse duration

1 x 10

household waste. Care for the environment and take

them to the collection points provided in accordance

with national or local regulations.

The product must not be disposed with

household waste.

Dispose of the product appropriately in

accordance with the national regulations in

force in your country.

Adhere to the national and country specific regula-

tions.

For the position of the type plate see drawing {J}.

Product specific treatment and waste management

information can be downloaded from the Leica

Geosystems home page at

http://www.leica-geosystems.com/treatment or

received from your Leica Geosystems dealer.

Care

Wipe off dirt with a damp, soft cloth. Do not immerse

the instrument in water. Do not use aggressive

cleaning agents or solutions.

and technical specifications).

Warranty

The Leica DISTO™ D2 comes with a three* year

warranty from Leica Geosystems.

More detailed information can be found at:

www.disto.com

Leica DISTO™ D2 762202b gb

Appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

Leica Geosystems AG, Heerbrugg, Switzerland has been certified as being equipped

with a quality system which meets the International Standards of Quality

Management and Quality Systems (ISO standard 9001) and Environmental

Management Systems (ISO standard 14001).

Total Quality Management - Our commitment to total customer satisfaction. Ask

your local Leica Geosystems agent for more information about our TQM program.

Switzerland 2008

Translation of original text (762202b)

Pat. No.: WO 9427164, WO 9818019, WO 0244754, WO 0216964,

US 5949531, EP 1195617, US 7030969, WO 03104748

Leica Geosystems AG

CH-9435 Heerbrugg

(Switzerland)

www.disto.com

Download from Www.Somanuals.com. All Manuals Search And Download.

La Crosse Technology Clock Radio WS 8055U User Manual
Lantronix Switch SW 94000 User Manual
Lenovo Laptop 20A7 User Manual
LG Electronics Flat Panel Television PJ250R User Manual
LG Electronics Home Security System LVC C500 User Manual
LG Electronics Refrigerator LBC22518 User Manual
Linear Smoke Alarm DXS 72 User Manual
MB QUART Car Speaker DTK 30 User Manual
Memorex MP3 Player MPD8505CP User Manual
Microsoft Computer Hardware C 97200 User Manual