Lantronix Server EDS MD16 User Manual

EDS-MD  
TM User Guide  
EDS-MD4  
EDS-MD8  
EDS-MD16  
Part Number 900-591  
Revision D November 2011  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
EDS-MD User Guide  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
EDS-MD User Guide  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
EDS-MD User Guide  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
EDS-MD User Guide  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
EDS-MD User Guide  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
EDS-MD User Guide  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
EDS-MD User Guide  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
EDS-MD User Guide  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix D: Lantronix Cables, Adapters  
and Serial Port Pinouts  
93  
EDS-MD User Guide  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
List of Figures  
EDS-MD User Guide  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
List of Tables  
Table 7-1 Network Interface Settings _________________________________________________46  
EDS-MD User Guide  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
EDS-MD User Guide  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1: Using This Guide  
Purpose and Audience  
This guide provides the information needed to configure, use, and update the EDS-MD4, EDS-  
MD8 and EDS-MD16. It is intended for system integrators who are installing this product into their  
designs.  
Note: EDS-MD device servers (which include models EDS-MD4, EDS-MD8 and  
EDSMD16) are commonly referred to as either EDS-MD4/8/16 or as EDS-MD when  
mentioned within a description equally applicable to any of the three models.  
Summary of Chapters  
The remaining chapters in this guide include:  
Chapter  
Description  
Main features of the product and the protocols it supports.  
Includes technical specifications.  
3: Installation of EDS-MD4/8/16 Device Instructions for installing the EDS-MD.  
Instructions for viewing the current configuration using  
DeviceInstaller.  
Instructions for accessing Web Manager and using it to configure  
settings for the device.  
Instructions for configuring network settings.  
Instructions for configuring line and tunnel settings.  
Instructions for configuring terminal and host settings.  
Instructions for configuring DNS, FTP, HTTP and Syslog settings.  
Instructions for configuring SSL security settings.  
Instructions to maintain the EDS-MD, view statistics, files, and  
diagnose problems.  
Instructions for configuring email, CLI and XML settings.  
Instructions for obtaining the latest firmware and updating the  
EDS-MD.  
Information about Virtual IP (VIP) features available on the device  
and instructions on configuring settings.  
Instructions on how to brand your device.  
Instructions for contacting Lantronix Technical Support.  
Instructions for converting binary values to hexadecimals.  
Appendix C: Compliance  
Lantronix compliance information.  
Information about the device driver for windows host.  
EDS-MD User Guide  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
1: Using This Guide  
Safety Information  
This section describes the safety precautions that should be followed when installing and  
operating the EDS-MD.  
Warning: This equipment is not suitable for use in the presence of a flammable  
anaesthetic mixture including air, oxygen or nitrous oxide.  
Cover  
Warning: Do not remove the cover of the EDS-MD. There are no user-serviceable  
parts inside. Opening or removing the cover may expose you to  
dangerous voltage that could cause fire or electric shock. Do not  
operate the EDS-MD if the housing is broken.  
Note: Refer all servicing to Lantronix.  
Power Plug  
When disconnecting the power cable from the socket, pull on the plug, not the cord.  
Always connect the power cord to a properly wired and grounded power source. Do not use  
adapter plugs or remove the grounding prong from the cord.  
Only use a power cord with a voltage and current rating greater than the voltage and current  
rating marked on the unit.  
Note: Unit is shipped with a power cord for medical application.  
Install the unit near an AC outlet that is easily accessible.  
Always connect any equipment used with the product to properly wired and grounded power  
sources.  
To help protect the product from sudden, transient increases and decreases in electrical  
power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).  
Do not connect or disconnect this product during an electrical storm.  
Input Supply  
Check nameplate ratings to assure there is no overloading of supply circuits that could affect  
over current protection and supply wiring.  
Grounding  
Maintain reliable grounding of this product.  
Pay particular attention to supply connections when connecting to power strips, rather than  
directly to the branch circuit.  
Fuses  
There are fuses on the internal power supply serviceable only by Lantronix.  
EDS-MD User Guide  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
1: Using This Guide  
Battery  
A Lithium battery cell inside the unit maintains the unit's date and time when the device is powered  
off. Do not attempt to replace it. The battery is serviceable only by Lantronix.  
Caution: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.  
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE  
RECOMMENDED BY THE MANUFACTURER. DISPOSE OF USED  
BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.  
Attention: IL Y A DANGER D'EXPLOSION S'IL Y A REMPLACEMENT INCORRECT  
DE LA BATTERIE, REMPLACER UNIQUEMENT AVEC UNE BATTERIE  
DU MÊME TYPE OU D'UN TYPE ÉQUIVALENT RECOMMANDÉ PAR LE  
CONSTRUCTEUR. METTRE AU REBUT LES BATTERIES USAGÉES  
CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT.  
Wall Mounting  
If wall-mounted units are installed, the following items must be considered:  
Do not install the unit in such a way that a hazardous stability condition results because of  
uneven loading. A drop or fall could cause injury.  
Make sure to install the EDS-MD in an environment with an ambient temperature less than the  
maximum operating temperature of the EDS-MD. Therefore, consideration should be given to  
installing the equipment in an environment compatible with the maximum ambient temperature  
(Tma) specified by the manufacturer.  
Install the equipment on a wall in such a way that the amount of airflow required for safe  
operation of the equipment is not compromised.  
Maintain reliable earthing of wall-mounted equipment. Give particular attention to supply  
connections other than direct connections to the branch circuit (e.g. use of power strips)  
because of the effect that overloading of the circuits might have on overcurrent protection and  
supply wiring. Appropriate consideration of equipment nameplate ratings should be used  
when addressing this concern.  
Before operating the EDS-MD, make sure the EDS-MD mounting is secured.  
Port Connections  
Only connect the network port to an Ethernet network that supports 10 Base-T/100 Base-TX/  
1000 Base-T.  
Only connect device ports to equipment with serial ports that support EIA-232 (formerly RS-  
232C).  
Unless specified otherwise, only connect USB ports to USB thumb drives.  
Warning: To avoid overloading and overheating, do not use a USB port as a  
charger port or a power port for other devices such as a cellular phone,  
PDA device, disk drive, etc.  
EDS-MD User Guide  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
1: Using This Guide  
Equipment Classifications  
Classification according to the type of protection against electric shock: Class I Equipment  
Classification according to the degree of protection against electric shock: No Applied Parts  
Classification according to the degree of protection against ingress of water: IP20  
Classification according to the mode of operation: Continuous Operation  
Environmental Conditions for Transportation and Storage  
An ambient temperature range of -30°C to +80°C  
A relative humidity range of 0% to 95%, noncondensing  
An atmospheric pressure range of 50 kPa to 106 kPa  
Cleaning Instructions  
1. Disconnect all cables and unplug ac power from the device.  
2. Prepare a disinfectant solution using 1 part bleach mixed with 9 parts water.  
3. Lightly moisten a tissue with the mild detergent and wipe down only the outside of the device.  
4. Allow the device to air-dry or wipe dry with a clean dry tissue before use.  
Caution: To avoid electric shock and for the device to work properly, do not allow  
cleaning solution get inside the device, specifically the interface port  
connectors or the ac inlet. Do not immerse the device in any liquid.  
Electromagnetic Interference  
This equipment has been tested and found to comply with the EMC limits for the Medical Device  
Directive 93/42/EEC (EN 55022 Class A and EN 60601-1-2). These limits are designed to provide  
reasonable protection against harmful interference in a typical medical installation. The equipment  
generates, uses and can radiate radio frequency energy and, if not installed and used in  
accordance with these instructions, may cause harmful interference to other devices in the vicinity.  
However, there is no guarantee that interference will not occur in a particular installation. If this  
equipment does cause harmful interference with other devices, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct the interference by one  
or more of the following measures:  
Reorient or relocate the receiving device  
Increase the separation between the equipment  
Connect the equipment into an outlet on a circuit different from that to which the other  
device(s) is connected  
Consult the manufacturer or field service technician for help  
EDS-MD User Guide  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
1: Using This Guide  
Additional Documentation  
Visit the Lantronix Web site at www.lantronix.com/support/documentation for the latest  
documentation and the following additional documentation.  
Document  
Description  
EDS-MD Command Reference  
Instructions for accessing Command Mode (the command line  
interface) using a Telnet connection, SSH connection or through the  
serial port. Detailed information about the commands. Also provides  
details for XML configuration and status.  
EDS-MD Quick Start Guide  
DeviceInstaller Online Help  
Instructions for getting the EDS-MD up and running.  
Instructions for using the Lantronix Windows-based utility to locate the  
EDS-MD and to view its current settings.  
Com Port Redirector Quick Start Instructions for using the Lantronix Windows-based utility to create  
and Online Help  
virtual com ports.  
Secure Com Port Redirector  
User Guide  
Instructions for using the Lantronix Windows-based utility to create  
secure virtual com ports.  
EDS-MD User Guide  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2: Introduction  
The EDS-MD4, EDS-MD8 and EDS-MD16 Ethernet Device Servers are complete network-  
enabling solutions. This device server allows system integrators and administrators to go to  
market quickly and easily with Ethernet networking and web server capabilities. EDS-MD models  
are available in 4, 8 and 16 port configurations.  
Key Features  
Power Supply: Direct plug-in to wall ac with universal 100-240 VAC input  
Controller: 32-bit ARM11 microprocessor running at 600 megahertz (Mhz)  
Memory: 64 megabit Flash, 2 gigabit DDR2 DRAM, and a 4 gigabyte SDHC card (internal  
only-not user replaceable).  
Ethernet: Gigabit Ethernet support (10/100/1000Base-T) speed auto-sensing, automatic MDI/  
MDIX (straight and cross-over cables are OK to use)  
Serial Ports: 4 to 16 ports depending on model (EDS-MD4, EDS-MD8 or EDS-MD16),  
electrically isolated from one another and other circuits. Hardware/Software handshaking  
capability. Custom/standard baud rates up to 921600 bits per second (bps).  
USB ports: 2 ports of fixed full-speed 2.0 USB Host, electrically isolated from one another and  
other circuits, capable of providing 0.5A each.  
Temperature Range: 0°C to +55°C.  
Applications  
The EDS-MD4/8/16 device server connects serial devices such as those listed below to Ethernet  
networks using the IP protocol family.  
Patient Monitoring Devices  
Glucose Analyzers  
Infusion Pumps  
Protocol Support  
The EDS-MD4/8/16 device server contains a full-featured IP stack. Supported protocols include:  
ARP, UDP, TCP, ICMP, DHCP, Auto IP, Telnet, SMTP, DNS, FTP, TFTP, and Syslog for  
network communications and management.  
TCP, UDP and tunneling to the serial port.  
TFTP for uploading/downloading files.  
FTP, SFTP, HTTPS and HTTP for firmware upgrades and uploading/downloading files.  
EDS-MD User Guide  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
2: Introduction  
Troubleshooting Capabilities  
The EDS-MD4/8/16 offers a comprehensive diagnostic toolset that lets you troubleshoot problems  
quickly and easily. Available from the CLI or Web Manager, the diagnostic tools let you:  
View memory and IP socket information.  
Perform ping and traceroute operations.  
Conduct forward or reverse DNS lookup operations.  
View all processes currently running on the EDS-MD, including CPU utilization.  
View system log messages.  
Configuration Methods  
After installation, the EDS-MD4/8/16 requires configuration. For the unit to operate correctly on a  
network, it must have a unique IP address on the network. There are four basic methods for  
logging into the EDS-MD4/8/16 and assigning IP addresses and other configurable settings:  
Web Manager: View and configure all settings easily through a web browser using the Lantronix  
DeviceInstaller: Configure the IP address and related settings and view current settings on the  
EDS-MD4, EDS-MD8 and EDS-MD16 using a Graphical User Interface (GUI) on a PC attached to  
Command Mode: There are two methods for accessing Command Mode (CLI): making a Telnet  
or SSH connection, or connecting a terminal (or a PC running a terminal emulation program) to the  
unit’s serial port. (See the EDS-MD4 Command Reference Guide for instructions and available  
commands.)  
XML: The EDS-MD4/8/16 supports XML-based configuration and setup records that make device  
configuration transparent to users and administrators. XML is easily editable with a standard text  
or XML editor. (See the EDS-MD Command Reference Guide for instructions and commands.)  
Addresses and Port Numbers  
Hardware Address  
The hardware address is also referred to as the Ethernet address, physical address, or MAC  
address. Sample hardware address:  
00-20-4A-14-01-18  
00:20:4A:14:01:18  
IP Address  
Every device connected to an IP network must have a unique IP address. This address references  
the specific unit.  
EDS-MD User Guide  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
2: Introduction  
Port Numbers  
Every TCP connection and every UDP datagram is defined by a destination and source IP  
TCP port number 23.  
The following is a list of the default server port numbers running on the EDS-MD4/8/16:  
TCP Port 22: SSH Server (Command Mode configuration)  
TCP Port 23: Telnet Server (Command Mode configuration)  
TCP Port 80: HTTP (Web Manager configuration)  
TCP Port 21: FTP  
UDP Port 30718: LDP (Lantronix Discovery Protocol) port  
TCP/UDP Port 10001: Tunnel 1  
Note: Additional TCP/UDP ports and tunnels will be available, depending on the product  
type. The default numbering of each additional TCP/UDP port and corresponding tunnel  
will increase sequentially (i.e., TCP/UDP Port 1000X: Tunnel X).  
Product Information Label  
The product information label on the unit contains the  
following information about the specific unit:  
Note: The hardware address on the  
label is also the product serial number.  
The hardware address on the label is the  
address for the Ethernet (eth0) interface.  
Bar code  
Product Revision  
Part Number  
Serial Number (MAC Address)  
Manufacturing Date Code  
Figure 2-1 EDS-MD Product Label  
Bar Code  
Serial Number  
Part Number  
SN: XXXXXXXXXXXXX  
PN: XXXXXXXXXXXXX  
Revision  
Rev: XXX  
YYWWW  
Made In:  
XXXXXXX  
Manufacturing  
Date Code  
EDS-MD User Guide  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
3: Installation of EDS-MD4/8/16 Device Servers  
This chapter describes how to install the EDS-MD4, EDS-MD8 and EDS-MD16 device servers.  
Package Contents  
Your EDS-MD4/8/16 package includes the following items:  
One EDS-MD device server (an EDS-MD4, EDS-MD8 or EDS-MD16)  
One RJ45 CAT 5E cable (part number 500-207-R) for network connection  
One RJ45 cable loopback adapter (part number 500-153)  
One power cord  
EDS-MD Quick Start Guide  
User-Supplied Items  
To complete your EDS-MD installation, you need the following items:  
RS-232 serial devices that require network connectivity. Each EDS-MD4/8/16 serial port  
supports a directly connected RS-232 serial device.  
A serial cable for each serial device to be connected to the EDS-MD4/8/16. All devices  
attached to the device ports support the RS-232C (EIA-232) standard. Category 5 cabling with  
RJ45 connections is used for the device port connections.  
Note: To connect an EDS-MD4/8/16 serial port to a DTE device, you need a DTE cable,  
such as the one supplied in your EDS-MD package, or an RJ45 patch cable and DTE  
adapter. To connect the EDS-MD4/8/16 serial port to a DCE device, you need a DCE  
(modem) cable, or an RJ45 patch cable and DCE adapter. For a list of the Lantronix  
cables and adapters you can use with the EDS-MD, see the Appendix D: Lantronix  
An available connection to your Ethernet network and an Ethernet cable.  
A working, properly grounded power outlet.  
Identifying Hardware Components  
Figure 3-1 shows the front of the EDS-MD16. Figure 3-2 shows the back of the EDS-MD4, EDS-  
MD8 or EDS-MD16.  
EDS-MD User Guide  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
3: Installation of EDS-MD4/8/16 Device Servers  
Figure 3-1 Front View of the EDS-MD16  
Note: EDS-MD4  
has 4 RJ45 Serial  
Ports and EDS-MD8  
has 8 RJ45 Serial  
Ports.  
Figure 3-2 Back View of the EDS-MD4, EDS-MD8 and EDS-MD16  
RJ45 Ethernet Ports  
USB Port  
Note: Ethernetports  
2 and 3 will become  
operational with a  
future firmware  
update.  
Power Connector  
Serial Ports  
In the front of the device, the EDS-MD4 has 4 serial ports, the EDS-MD8 has 8 serial ports, and  
the EDS-MD16 has 16 serial ports. All are configured as DTE and support up to 921600 baud.  
Ethernet Port  
The back panel of the EDS-MD4/8/16 provides a network interface via the “Main 1” RJ45 port. This  
port can connect to an Ethernet network at 10/100/1000Base-T. The Speed LED on the back of  
the EDS-MD shows the connection of the attached Ethernet network. The EDS-MD4/8/16 can be  
configured to operate at a fixed Ethernet speed and duplex mode (half- or full-duplex). Otherwise  
by default, the EDS-MD auto-negotiates the connection to the Ethernet network.  
LEDs  
Light-emitting diodes (LEDs) on the EDS-MD show status information.  
Each serial port has a corresponding status LED.  
The Ethernet port LEDs indicate Speed, Activity, Power, and Status.  
The tables below describe the LEDs on the EDS-MD4, EDS-MD8 or EDS-MD16.  
Table 3-3 System LEDs on the Top of EDS-MD  
LED  
Description  
Steady Green  
Off  
Unit operational.  
Unit powered down or not operational.  
EDS-MD User Guide  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
3: Installation of EDS-MD4/8/16 Device Servers  
Table 3-4 Serial Indicator LEDs on the Top of EDS-MD  
LED  
Green  
Red  
Off  
Description  
Indicates there is a tunnel connection to or from the EDS-MD.  
Not supported.  
There is no tunnel connection on the serial line.  
Note: Number of Serial LEDs correspond with the EDS-MD model number. For  
instance, EDS-MD4 has 4 LEDs, EDS-MD8 has 8 LEDs, and EDS-MD16 has 16 LEDs.  
Table 3-5 RJ45 LEDs on the Back Panel (Ethernet Indicators).  
LED  
Description  
Left LED Green  
Connected at 1000 Mbps.  
Connected at 100 Mbps.  
Connected at 10 Mbps or no link.  
Full duplex with no activity  
Full duplex with activity  
Half duplex with no activity.  
Left LED Amber  
Left LED Off  
Right LED Green (Solid)  
Right LED Green (Blinking)  
Right LED Amber (Solid)  
Right LED Amber (Blinking) Half duplex with activity.  
Right LED Off  
No connection.  
Reset to Default Button  
The EDS-MD can be restored to factory defaults which includes clearing all networking settings.  
The IP address, gateway and netmask are set to all zeros. The reset-to-default button is located  
on the side of the housing, accessible with a paper clip or other similar object, through a pin hole.  
To restore factory default settings:  
1. Power cycle the unit.  
2. During the bootup, hold down the reset-to-default button for a minimum of 25 seconds.  
3. Release the button. The firmware restores factory default settings to the configuration.  
EDS-MD User Guide  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
3: Installation of EDS-MD4/8/16 Device Servers  
Technical Specification  
Category  
Description  
NETWORK INTERFACE  
Ethernet Ports  
3 RJ45 10Base-T/100Base-TX/1000Base-T Ethernet ports  
Auto sensing  
Automatic MDI/MDI-X crossover  
Full duplex IEEE 802.3x flow control  
Half-duplex back pressure flow control  
Left LED Indicator  
See Table 3-5.  
See Table 3-5.  
1.5 KVAC  
Right LED Indicator  
Isolation from internal circuit  
Isolation from adjacent port  
1.5 KVAC  
USB INTERFACE  
USB Ports  
2 of USB-A Host, USB 2.0, Full Speed only  
Output Capability  
0.5 A  
Isolation from internal circuit  
Isolation from adjacent port  
1.5 KVAC  
1.5 KVAC  
SERIAL INTERFACE  
Serial Ports  
Options of 4-port, 8-port, 16-port  
RS232 Serial Ports DTE via RJ45 connectors  
Baud rate  
Selectable from 300 bps to 921600 bps  
Serial Line Formats  
Characters: 7 or 8 data bits  
Stop bits: 1 or 2  
Parity: odd, even, none  
Modem Control  
Flow Control  
DTR/DSR  
Hardware: CTS/RTS  
Software: XON/XOFF  
Serial LED Indicators  
See Table 3-4.  
Protection from ESD  
15kV (human body model)  
Isolation from internal circuit  
Isolation from adjacent port  
1.5 KVAC  
1.5 KVAC  
Reset-to-Default-Parameters  
Switch  
Side panel pin-hole recessed push button switch  
POWER RATING  
Power Input AC Connector  
Power Usage  
IEC60320 C14 receptacle with no power switch  
100-240 VAC, 50/60 HZ, 0.4M  
EDS-MD User Guide  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3: Installation of EDS-MD4/8/16 Device Servers  
Category (continued)  
Description  
PHYSICALS  
Dimensions  
Weight  
L x W x H = 8.25 x 7.5 x 2.4 in. (21 x 19 x 6 cm)  
16-port = 2.0 lbs (0.9 Kg)  
8-port = 1.8 lbs (0.82 Kg)  
4-port = 1.75 lbs (0.8 Kg)  
Environmental  
Temperature Operating 0° to 55°C (32° to 131°F)  
Temperature for Transportation and Storage -30° to 80°C  
Humidity 0% to 95% non-condensing  
Atmospheric Pressure 50 kPa to 105 kPa  
Humidity Operating  
20% to 90% relative humidity, non-condensing  
Installing the EDS-MD  
Finding a Suitable Location  
You can install the EDS-MD4, EDS-MD8 or EDS-MD16 either on a shelf, on a desktop or  
mounted on the wall.  
If using AC power, do not use outlets controlled by a wall switch.  
Connect the EDS-MD to one or more serial devices  
All EDS-MD serial ports support RS-232 devices.  
1. Power off the serial devices.  
2. Attach a CAT 5 serial cable between the EDS-MD and your serial device. See Appendix D:  
adapters you can use.  
3. Connect an Ethernet cable between the EDS-MD Ethernet port and your Ethernet network.  
4. Insert the power cord into the back of the EDS-MD. Plug the other end into an AC wall outlet.  
5. Power up the serial devices.  
EDS-MD User Guide  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
4: Using DeviceInstaller  
This chapter covers the steps for locating a EDS-MD4/8/16 unit and viewing its properties and  
device details. DeviceInstaller is a free utility program provided by Lantronix that discovers,  
configures, upgrades and manages Lantronix Device Servers.  
Notes:  
For instructions on using DeviceInstaller to configure the IP address and related  
settings or for more advanced features, see the DeviceInstaller Online Help.  
Auto IP generates a random IP address in the range of 169.254.0.1 to  
169.254.255.254, with a netmask of 255.255.0.0, if no BOOTP or DHCP server is  
found. These addresses are not routable.  
Accessing EDS-MD Using DeviceInstaller  
Note: Make note of the MAC address. It is needed to locate the EDS-MD4/8/16 using  
DeviceInstaller.  
To use the DeviceInstaller utility, first install the latest version from the downloads page on the  
Lantronix web site www.lantronix.com/downloads.  
1. Run the executable to start the installation process and respond to the installation wizard  
prompts. (If prompted to select an installation type, select Typical.)  
2. Click Start -> All Programs -> Lantronix -> DeviceInstaller -> DeviceInstaller.  
3. When DeviceInstaller starts, it will perform a network device search. To perform another  
search, click Search.  
4. Expand the EDS-MD4, EDS-MD8 or EDS-MD16 folder by clicking the + symbol next to the  
folder icon. The list of available Lantronix EDS-MD4/8/16 devices appears.  
5. Select the EDS-MD4/8/16 unit by expanding its entry and clicking on its IP address to view its  
configuration.  
6. On the right page, click the Device Details tab. The current EDS-MD4/8/16 configuration  
appears. This is only a subset of the full configuration; the full configuration may be accessed  
via Web Manager, CLI or XML.  
Device Detail Summary  
Note: The settings are Display Only in this table unless otherwise noted  
Current Settings  
Name  
Description  
Name identifying the EDS-MD.  
The name associated with the EDS-MD module’s current IP address, if  
the IP address was obtained dynamically.  
DHCP Device Name  
EDS-MD User Guide  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
4: Using DeviceInstaller  
Current Settings (continued)  
Description  
Configurable field. Enter a group to categorize the EDS-MD. Double-  
click the field, type in the value, and press Enter to complete. This group  
name is local to this PC and is not visible on other PCs or laptops using  
DeviceInstaller.  
Group  
Configurable field. Enter comments for the EDS-MD. Double-click the  
field, type in the value, and press Enter to complete. This description or  
comment is local to this PC and is not visible on other PCs or laptops  
using DeviceInstaller.  
Comments  
Device Family  
Type  
Shows the EDS device family type as “EDS”.  
Shows the device type as “EDS-MD”.  
ID  
Shows the EDS-MD ID embedded within the unit.  
Shows the EDS-MD hardware (MAC) address.  
Shows the firmware currently installed on the EDS-MD.  
Provides additional information on the firmware version.  
Hardware Address  
Firmware Version  
Extended Firmware Version  
Shows the EDS-MD status as Online, Offline, Unreachable (the EDS-  
MD is on a different subnet), or Busy (the EDS-MD is currently  
performing a task).  
Online Status  
IP Address  
Shows the EDS-MD current IP address. To change the IP address, click  
the Assign IP button on the DeviceInstaller menu bar.  
Appears “Dynamically” if the EDS-MD automatically received an IP  
address (e.g., from DHCP). Appears “Statically” if the IP address was  
configured manually.  
IP Address was Obtained  
If the IP address was assigned dynamically, the following fields appear:  
Obtain via DHCP with values of True or False.  
Obtain via BOOTP with values of True or False.  
Shows the subnet mask specifying the network segment on which the  
EDS-MD resides.  
Subnet Mask  
Gateway  
Shows the IP address of the router of this network.  
There is no default.  
Number of Ports  
Shows the number of serial ports on this EDS-MD.  
Shows False, indicating configurable pins are not available on the EDS-  
MD.  
Supports Configurable Pins  
Supports Email Triggers  
Telnet Enabled  
Telnet Port  
Shows True, indicating email triggers are available on the EDS-MD.  
Indicates whether Telnet is enabled on this EDS-MD.  
Shows the EDS-MD port for Telnet sessions.  
Web Enabled  
Indicates whether Web Manager access is enabled on this EDS-MD.  
Shows the EDS-MD port for Web Manager configuration (if Web  
Enabled field is True).  
Web Port  
Shows True, indicating the EDS-MD firmware is upgradable as newer  
versions become available.  
Firmware Upgradable  
EDS-MD User Guide  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5: Configuration Using Web Manager  
This chapter describes how to configure the EDS-MD4, EDS-MD8 and EDS-MD16 using Web  
Manager, the Lantronix browser-based configuration tool. The unit’s configuration is stored in  
nonvolatile memory and is retained without power. All changes take effect immediately, unless  
otherwise noted. It contains the following sections:  
Accessing Web Manager  
Note: You can also access the Web Manager by selecting the Web Configuration tab on  
the DeviceInstaller window.  
To access Web Manager, perform the following steps:  
1. Open a standard web browser. Lantronix supports the latest version of Internet Explorer,  
Mozilla Suite, Mozilla Firefox, Safari, Chrome or Opera.  
2. Enter the IP address of the EDS-MD4/8/16 in the address bar. The IP address may have been  
assigned manually using DeviceInstaller (see the EDS-MD Quick Start Guide) or automatically  
by DHCP.  
3. Enter your username and password.The factory-default username is “admin” and the  
password is “PASS.” The Device Status web page displays configuration, network settings,  
line settings, tunneling settings, and product information.  
Note: The Logout button is available on any web page. Logging out of the web page  
would force re-authentication to take place the next time the web page is accessed.  
EDS-MD User Guide  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
5: Configuration Using Web Manager  
Device Status Page  
The Device Status page is the first page that appears after you log into the Web Manager. It also  
appears when you click Status in the Main Menu.  
EDS-MD User Guide  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5: Configuration Using Web Manager  
Web Manager Page Components  
The layout of a typical Web Manager page is below.  
Figure 5-1 Components of the Web Manager Page  
Logout  
button  
Links to  
subpages  
Items to  
configure  
Header  
Menu Bar  
Footer  
Information  
Configuration and/or Status Area  
and Help Area  
The menu bar always appears at the left side of the page, regardless of the page shown. The  
menu bar lists the names of the pages available in the Web Manager. To bring up a page, click it in  
the menu bar.  
The main area of the page has these additional sections:  
At the very top, many pages, such as the one in the example above, enable you to link to  
sub pages. On some pages, you must also select the item you are configuring, such as a  
line or a tunnel.  
In the middle of many pages, you can select or enter new configuration settings. Some  
pages show status or statistics in this area rather than allow you to enter settings.  
At the bottom of most pages, the current configuration is displayed. In some cases, you  
can reset or clear a setting.  
EDS-MD User Guide  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
5: Configuration Using Web Manager  
The information or help area shows information or instructions associated with the page.  
A Logout link is available at the upper right corner of every web page. In Chrome or  
Safari, it is necessary to close out of the browser to completely logout. If necessary,  
reopen the browser to log back in.  
The footer appears at the very bottom of the page. It contains copyright information and a  
link to the Lantronix home page.  
Navigating the Web Manager  
The Web Manager provides an intuitive point-and-click interface. A menu bar on the left side of  
each page provides links you can click to navigate from one page to another. Some pages are  
read-only, while others let you change configuration settings.  
Note: There may be times when you must reboot the EDS-MD4/8/16 for the new  
configuration settings to take effect. The chapters that follow indicate when a change  
requires a reboot. Anytime you reboot the unit, this operation will take some time to  
complete. Please wait a minimum of 5 seconds after rebooting the unit before attempting  
to make any subsequent connections.  
Web Manager Page Description  
See  
Page  
Status  
CLI  
Shows product information and network, line, and tunneling settings.  
Shows Command Line Interface (CLI) statistics and lets you change the  
current CLI configuration settings.  
Diagnostics  
DNS  
Lets you perform various diagnostic procedures.  
Shows the current configuration of the DNS subsystem and the DNS cache. 52  
Email  
Shows email statistics and lets you clear the email log, configure email  
settings, and send an email.  
Filesystem  
FTP  
Shows file system statistics and lets you browse the file system to view a file, 65  
create a file or directory, upload files using HTTP, copy a file, move a file, or  
perform TFTP actions.  
Shows statistics and lets you change the current configuration for the File  
Transfer Protocol (FTP) server.  
Host  
Lets you view and change settings for a host on the network.  
HTTP  
Shows HyperText Transfer Protocol (HTTP) statistics and lets you change the 54  
current configuration and authentication settings.  
Line  
Shows statistics and lets you change the current configuration and Command 35  
mode settings of a serial line.  
Network  
Protocol Stack  
Query Port  
RSS  
Shows status and lets you configure the network interface.  
Lets you perform lower level network stack-specific activities.  
Lets you change configuration settings for the query port.  
Lets you change current Really Simple Syndication (RSS) settings.  
SSH  
Lets you change the configuration settings for SSH server host keys, SSH  
server authorized users, SSH client known hosts, and SSH client users.  
SSL  
Lets you upload an existing certificate or create a new self-signed certificate. 61  
EDS-MD User Guide  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5: Configuration Using Web Manager  
Web Manager Page Description  
(continued)  
See  
Page  
Syslog  
Lets you specify the severity of events to log and the server and ports to  
which the syslog should be sent.  
System  
Lets you reboot device, restore factory defaults, upload new firmware, and  
change the device long and short names.  
Terminal  
Tunnel  
VIP  
Lets you change current settings for a terminal.  
91  
Lets you change the current configuration settings for a tunnel.  
Lets you configure Virtual IP addresses to be used in Tunnel Accept Mode  
and Tunnel Connect Mode.  
XML  
Lets you export XML configuration and status records, and import XML  
configuration records.  
EDS-MD User Guide  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6: Line and Tunnel Settings  
The EDS-MD4, EDS-MD8 and EDS-MD16 contains four, eight or sixteen Lines, depending on the  
specific model. All lines use standard RS232 serial ports.  
RS232/RS485  
All lines can be configured to operate in the following modes:  
RS232  
All serial settings such as Baud Rate, Parity, Data Bits, etc, apply to these Lines.  
Line Settings  
The Line Settings allow configuration of the serial Lines (ports).  
Some settings may be specific to only certain Lines. Such settings are noted below.  
Table 6-1 Line Configuration Settings  
Line Settings  
Name  
Description  
Enter a name or short description for the line, if desired. By default, there is no name  
specified. A name that contains white space must be quoted.  
State  
Select to Enable or Disable the operational state of the Line. The default is Enable.  
Protocol  
Set the operational protocol for the Line. The default is Tunnel. Choices are:  
None  
Tunnel = Serial-Network tunneling protocol.  
Baud Rate  
Set the Baud Rate (speed) of the Line. The default is 9600.  
Any set speed between 300 and 921600 may be selected: 300, 600, 1200, 2400,  
4800, 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600. When  
selecting a Custom baud rate, you may manually enter any value between 300 and  
5000000.  
Note: Custom baud rates are not supported when a line is configured for Command  
Mode.  
Parity  
Set the Parity of the Line. The default is None.  
Data Bits  
Stop Bits  
Flow Control  
Xon Char  
Set the number of data bits for the Line. The default is 8.  
Set the number of stop bits for the Line. The default is 1.  
Set the flow control for the Line. The default is None.  
Set Xon Char to be used when Flow Control is set to Software. Prefix decimal with \  
or prefix hexadecimal with 0x or prefix a single control character <control>.  
Xoff Char  
Gap Timer  
Set Xoff Char to be used when Flow Control is set to Software. Prefix decimal with \  
or prefix hexadecimal with 0x or prefix a single control character <control>.  
Set the Gap Timer delay to Set the number of milliseconds to pass from the last  
character received before the driver forwards the received serial bytes. By default,  
the delay is four character periods at the current baud rate (minimum 1 msec).  
Threshold  
Set the number of threshold bytes which need to be received in order for the driver to  
forward received characters.  
EDS-MD User Guide  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
6: Line and Tunnel Settings  
Table 6-2 Line Command Mode Settings  
Description  
Line Command  
Mode Settings  
Mode  
Set the Command Mode state of the Line. When in Command Mode, a CLI session  
operates exclusively on the Line. Choices are:  
Always  
User Serial String  
Disabled  
Note: In order to enable Command Mode on the Line, Tunneling on the Line must  
be Disabled (both Connect and Accept modes). Also, custom baud rates are not  
supported in Command Mode.  
Wait Time  
Enter the amount of time to wait during boot time for the Serial String. This timer  
starts right after the Signon Message has been set on the Serial Line and applies  
only if mode is “Use Serial String”.  
Serial String  
Enter the Text or Binary string of bytes that must be read on the Serial Line during  
boot time in order to enable Command Mode. It may contain a time element to  
specify a required delay in milliseconds x, formed as {x}. Applies only if mode is  
“User Serial String”. It may contain a binary character(s) of the form [x]. For  
example, use decimal [12] or hex [0xc].  
Echo Serial String Select Enable or Disable for Echo Serial String. Applies only if mode is “User Serial  
String”. Select enable to echo received characters backed out on the line while  
looking for the serial string.  
Signon Message  
Enter the string of bytes to be sent to the Serial Line during boot time. It may contain  
a binary character(s) of the form [x]. For example, use decimal [12] or hex [0xc].  
To Configure Line Settings  
Note: The following section describes the steps to view and configure Line 1 settings;  
these steps apply to other line instances of the device.  
Using Web Manager  
To configure a specific line, click Line in the menu and select Line 1 -> Configuration (Table  
6-1).  
To configure a specific line in Command Mode, click Line in the menu and select Line 1 ->  
Command Mode (Table 6-2).  
Using the CLI  
To enter Line 1 command level: enable -> line 1  
Using XML  
Include in your file: <configgroup name="line" instance="1">  
Include in your file: <configgroup name="serial command mode" instance="1">  
To View Line Statistics  
Using Web Manager  
To view statistics for a specific line, click Line in the menu and select Line 1 -> Statistics.  
EDS-MD User Guide  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
6: Line and Tunnel Settings  
Using the CLI  
To view Line statistics: enable -> line 1, show statistics  
Using XML  
Include in your file: <statusgroup name=”line” instance=”1”>  
Tunnel Settings  
Tunneling allows serial devices to communicate over a network, without “being aware” of the  
devices which establish the network connection between them. Tunneling parameters are  
configured using the Tunnel menu and submenus.The Tunnel settings allow you to configure how  
the Serial-Network tunneling operates. Tunneling is available on all serial Lines. The connections  
on one serial Line are separate from those on another serial port.  
Note: The following section describes the steps to view and configure Tunnel 1 settings;  
these steps apply to other tunnel instances of the device.  
Serial Settings  
These serial settings for the tunnel apply to the Serial Line interface. The Line Settings and  
Protocol are displayed for informational purposes and must be configured from the Line settings.  
Table 6-3 Tunnel Serial Settings  
Tunnel Serial  
Settings  
Description  
Line Settings  
Protocol  
DTR  
Line Settings information here is display only. Go to the section, To Configure  
Line Settings to modify these settings.  
Protocol information here is display only. Go to the section, To Configure  
Line Settings to modify these settings.  
Select the conditions in which the Data Terminal Ready (DTR) control signal  
on the Serial Line are asserted. Choices are:  
Unasserted  
TruPort = the DTR is asserted whenever either a connect or an accept  
mode tunnel connection is active with the Telnet Protocol RFC2217 saying  
that the remote DSR is asserted.  
Asserted while connected = the DTR is asserted whenever either a  
connect or an accept mode tunnel connection is active.  
Continuously asserted  
To Configure Tunnel Serial Settings  
Using Web Manager  
To configure the Serial Settings for a specific tunnel, click Tunnel in the menu and select  
Tunnel 1 -> Serial Settings.  
EDS-MD User Guide  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
6: Line and Tunnel Settings  
Using the CLI  
To enter Tunnel 1 command level: enable -> tunnel 1 -> serial  
Using XML  
Include in your file: <configgroup name=”tunnel serial” instance=”1”>  
Packing Mode  
With Packing, data from the serial Line is not sent over the network immediately. Instead, data is  
queued and sent in segments, when either the timeout or byte threshold is reached. Packing  
applies to both Accept and Connect Modes.  
Table 6-4 Tunnel Packing Mode Settings  
Tunnel Packing Mode  
Settings  
Description  
Mode  
Configure the Tunnel Packing Mode. Choices are:  
Disable = Data not packed.  
Timeout = data sent after timeout occurs.  
Send Character = data sent when the Send Character is read on the Serial  
Line.  
Threshold  
Set the threshold (byte count). If the received serial data reaches this  
threshold, then the data will be sent on the network. Valid range is 100 to  
1450 bytes. Default is 512.  
Timeout  
Set the timeout value, in milliseconds, after the first character is received on  
the serial Line, before data is sent on the network. Valid range is 1 to 30000  
milliseconds. Default is 1000.  
Send Character  
Enter Control Characters in any of the following forms:  
<control>J  
0xA (hexadecimal)  
\10 (decimal)  
If used, the Send Character is a single printable character or a control  
character that, when read on the Serial Line, forces the queued data to be  
sent on the network immediately.  
Trailing Character  
Enter Control Characters in any of the following forms:  
<control>J  
0xA (hexadecimal)  
\10 (decimal).  
If used, the Trailing Character is a single printable character or a control  
character that is injected into the outgoing data stream right after the Send  
Character. Disable the Trailing Character by blanking the field (setting it to  
<None>).  
To Configure Tunnel Packing Mode Settings  
Using Web Manager  
To configure the Packing Mode for a specific tunnel, click Tunnel in the menu and select  
Tunnel 1 -> Packing Mode.  
EDS-MD User Guide  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
6: Line and Tunnel Settings  
Using the CLI  
To enter the Tunnel 1 Packing command level: enable -> tunnel 1 -> packing  
Using XML  
Include in your file: <configgroup name="tunnel packing" instance="1">  
Accept Mode  
In Accept Mode, the EDS-MD4/8/16 listens (waits) for incoming connections from the network. A  
remove node on the network initiates the connection.  
The configurable local port is the port the remote device connects to for this connection. There is  
no remote port or address. Supported serial lines and associated local port numbers progress  
sequentially in matching value. For instance, the default local port is 10001 for serial line 1 and the  
default local port for serial line 2 is 10002, and so on for the number of serial lines supported.  
Serial data can still be received while waiting for a network connection, keeping in mind serial data  
buffer limitations.  
Table 6-5 Tunnel Accept Mode Settings  
Tunnel Accept Mode  
Settings  
Description  
Mode  
Set the method used to start a tunnel in Accept mode. Choices are:  
Disable = do not accept an incoming connection.  
Always = accept an incoming connection. (default)  
Any Character = start waiting for an incoming connection when any  
character is read on the serial line.  
Start Character = start waiting for an incoming connection when the  
start character for the selected tunnel is read on the serial line.  
Modem Control Asserted = start waiting for an incoming connection as  
long as the Modem Control pin (DSR) is asserted on the serial line until  
a connection is made.  
Modem Emulation = start waiting for an incoming connection when  
triggered by modem emulation AT commands. Connect mode must  
also be set to Modem Emulation.  
Local Port  
Protocol  
Set the port number for use as the network local port. The default local port  
number for each supported serial line number progresses sequentially in  
equal value so that Tunnel X : 1000X. For example:  
Tunnel 1 : 10001  
Tunnel 2 : 10002  
Select the protocol type for use with Accept Mode:  
SSH  
SSL  
TCP (default protocol)  
TCP AES  
Telnet  
TCP Keep Alive  
Enter the time, in milliseconds, theEDS-MD waits during a silent  
connection before checking if the currently connected network device is  
still on the network. If the unit then gets no response after 1 attempt, it  
drops the connection. Enter 0 to disable.  
EDS-MD User Guide  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
6: Line and Tunnel Settings  
Tunnel Accept Mode  
Settings (continued)  
Description  
Flush Serial  
Set whether the serial Line data buffer is flushed upon a new network  
connection. Choices are:  
Enabled = serial data buffer is flushed on network connection  
Disabled = serial data buffer is not flushed on network connection  
(default)  
Block Serial  
Set whether Block Serial is enabled for debugging purposes. Choices are:  
Enabled = if Enabled, incoming characters from the Serial Line will not  
be forwarded to the network. Instead, they will be buffered and will  
eventually flow off the Serial Line if hardware or software flow control is  
configured.  
Disabled = this is the default setting; incoming characters from the  
Serial Line are sent on into the network. Any buffered characters are  
sent first.  
Block Network  
Set whether Block Network is enabled for debugging purposes. Choices  
are:  
Enabled = if Enabled, incoming characters from the network will not be  
forwarded to the Serial Line. Instead, they will be buffered and will  
eventually flow off the network side.  
Disabled = this is the default setting; incoming characters from the  
network are sent on into the Serial Line. Any buffered characters are  
sent first.  
Password  
Enter a password. This password can be up to 31 characters in length and  
must contain only alphanumeric characters and punctuation. When set,  
clients must send the correct password string to the unit within 30 seconds  
from opening network connection in order to enable data transmission.  
The password sent to the unit must be terminated with one of the following:  
0A (Line Feed)  
00 (Null)  
0D 0A (Carriage Return/Line Feed)  
0D 00 (Carriage Return/Null)  
If, Prompt for Password is set to Enabled, the user will be prompted for  
the password upon connection.  
Email on Connect  
Select an email profile number to which an email notification will be sent  
upon the establishment of an accept mode tunnel.  
Email on Disconnect  
Select an email profile number to which an email notification will be sent  
upon the disconnection of an accept mode tunnel.  
To Configure Tunnel Accept Mode Settings  
Using Web Manager  
To configure the Accept Mode for a specific tunnel, click Tunnel in the menu and select  
Tunnel 1 -> Accept Mode.  
Using the CLI  
To enter Tunnel 1 Accept Mode command level: enable -> tunnel 1 -> accept  
Using XML  
Include in your file: <configgroup name="tunnel accept" instance="1">  
EDS-MD User Guide  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
6: Line and Tunnel Settings  
Connect Mode  
In Connect Mode, theEDS-MD4/8/16 continues to attempt an outgoing connection on the network,  
until established. If the connection attempt fails or the connection drops, then it retries after a  
timeout. The remote node on the network must listen for the Connect Mode’s connection.  
For Connect Mode to function, it must be enabled, have a remote station (node) configured, and a  
remote port configured (TCP or UDP). When established, Connect Mode is always on. Enter the  
remote station as an IP address or DNS name. TheEDS-MD4/8/16 will not make a connection  
unless it can resolve the address.  
For Connect Mode using UDP, theEDS-MD4/8/16 accepts packets from any device on the  
network. It will send packets to the last device that sent it packets.  
Note: The Port in Connect Mode is not the same port configured in Accept Mode.  
The TCP keepalive time is the time in which probes are periodically sent to the other end of the  
connection. This ensures the other side is still connected.  
Table 6-6 Tunnel Connect Mode Settings  
Tunnel Connect Mode  
Settings  
Description  
Mode  
Set the method to be used to attempt a connection to a remote host or  
device. Choices are:  
Disable = an outgoing connection is never attempted. (default)  
Always = a connection is attempted until one is made. If the connection  
gets disconnected, the EDS-MD retries until it makes a connection.  
Any Character = a connection is attempted when any character is read  
on the serial line.  
Start Character = a connection is attempted when the start character for  
the selected tunnel is read on the serial line.  
Modem Control Asserted = a connection is attempted as long as the  
Modem Control pin (DSR) is asserted, until a connection is made.  
Modem Emulation = a connection is attempted when triggered by  
modem emulation AT commands.  
Local Port  
Host 1  
Enter an alternative Local Port. The Local Port is set to <Random> by  
default but can be overridden. Blank the field to restore the default.  
Click on the displayed information to expand it for editing. If <None> is  
displayed, clicking it will allow you to configure a new host. At least one Host  
is required to enable Connect Mode as this information is necessary to  
connect to that host.  
Reconnect Timer  
Flush Serial Data  
Set the value of the reconnect timeout (in milliseconds) for outgoing  
connections established by the device. Valid range is 1 to 65535  
milliseconds. Default is 15000.  
Set whether the serial Line data buffer is flushed upon a new network  
connection. Choices are:  
Enabled = serial data buffer is flushed on network connection  
Disabled = serial data buffer is not flushed on network connection  
(default)  
EDS-MD User Guide  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
6: Line and Tunnel Settings  
Tunnel Connect Mode  
Settings (continued)  
Description  
Block Serial  
Set whether Block Serial is enabled for debugging purposes. Choices are:  
Enabled = If Enabled, incoming characters from the Serial Line will not be  
forwarded to the network. Instead, they will be buffered and will  
eventually flow off the Serial Line if hardware or software flow control is  
configured.  
Disabled = this is the default setting; incoming characters from the Serial  
Line are sent on into the network. Any buffered characters are sent first.  
Block Network  
Set whether Block Network is enabled for debugging purposes. Choices are:  
Enabled = If Enabled, incoming characters from the network will not be  
forwarded to the Serial Line. Instead, they will be buffered and will  
eventually flow off the network side.  
Disabled = this is the default setting; incoming characters from the  
network are sent on into the Serial Line. Any buffered characters are sent  
first.  
Email on Connect  
Select an email profile number to which an email notification will be sent  
upon the establishment of an accept mode tunnel.  
Email on Disconnect  
Select an email profile number to which an email notification will be sent  
upon the disconnection of an accept mode tunnel.  
To Configure Tunnel Connect Mode Settings  
Using Web Manager  
To configure the Connect Mode for a specific tunnel, click Tunnel in the menu and select  
Tunnel 1 -> Connect Mode.  
Using the CLI  
To enter the Tunnel 1 Connect Mode command level: enable -> tunnel 1 -> connect  
Using XML  
Include in your file: <configgroup name="tunnel connect" instance="1">  
Disconnect Mode  
Specifies the optional conditions for disconnecting any Accept Mode or Connect Mode connection  
that may be established. If any of these conditions are selected but do not occur and the network  
disconnects to the device, a Connect Mode connection will attempt to reconnect. However, if none  
of these conditions are selected, a closure from the network is taken as a disconnect.  
Table 6-7 Tunnel Disconnect Mode Settings  
Tunnel Disconnect  
Mode Settings  
Description  
Stop Character  
Enter the Stop Character which when received on the Serial Line, disconnects  
the tunnel. The Stop Character may be designated as a single printable  
character or as a control character. Control characters may be input in any of  
the following forms: <control>J or 0xA(hexadercimal) or \10 (decimal).  
Disable the Stop Character by blanking the field to set it to <None>.  
EDS-MD User Guide  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
6: Line and Tunnel Settings  
Tunnel Disconnect  
Mode Settings  
Description  
Modem Control  
Set whether Modem Control enables disconnect when the Modem Control pin  
is not asserted on the Serial Line. Choices are:  
Enabled  
Disabled (default)  
Timeout  
Enter the number of milliseconds a tunnel may be idle before disconnection.  
The value of zero disables the idle timeout.  
Flush Serial Data  
Set whether to flush the Serial Line when the Tunnel is disconnected. Choices  
are:  
Enabled  
Disabled (default)  
To Configure Tunnel Disconnect Mode Settings  
Using Web Manager  
To configure the Disconnect Mode for a specific tunnel, click Tunnel in the menu and select  
Tunnel 1 -> Disconnect Mode.  
Using the CLI  
To enter the Tunnel 1 Disconnect command level: enable -> tunnel 1 -> disconnect  
Using XML  
Include in your file: <configgroup name=”tunnel disconnect” instance=”1”>  
Modem Emulation  
Some older equipment is designed to attach to a serial port and dial into a network with a modem.  
This equipment uses AT commands to control the connection. For compatibility with these older  
devices on modern networks, our product mimics the behavior of the modem.  
Table 6-8 Tunnel Modem Emulation Settings  
Tunnel Modem  
Description  
Emulation Settings  
Echo Pluses  
Set whether the pluses will be echoed back during a “pause +++ pause”  
escape sequence on the Serial Line. Choices are:  
Enabled  
Disabled (default)  
Echo Commands  
Verbose Response  
Set whether characters read on the Serial Line will be echoed, while the Line  
is in Modem Command Mode. Choices are:  
Enabled  
Disabled (default)  
Set whether Modem Response Codes are sent out on the Serial Line.  
Choices are:  
Enabled  
Disabled (default)  
EDS-MD User Guide  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
6: Line and Tunnel Settings  
Tunnel Modem  
Description  
Emulation Settings  
Response Type  
Select a representation for the Modem Response Codes sent out on the Serial  
Line. Choices are:  
Text (ATV1) (default)  
Numeric (ATV0)  
Error Unknown  
Commands  
Set whether the Error Unknown Commands is enabled (ATU0) and ERROR is  
returned on the Serial Line for unrecognized AT commands. OTherwise  
(ATU1) OK is returned for unrecognized AT commands. Choices are:  
Enabled  
Disabled (default)  
Incoming Connection  
Set how and if requests are answered after an incoming RING (ATS0=2).  
Choices are:  
Disabled (default)  
Automatic  
Manual  
Connect String  
Enter the customized Connect String sent to the Serial Line with the Connect  
Modem Response Code.  
Display Remote IP  
Set whether the Display Remote IP is enabled so that the incoming RING sent  
on the Serial Line is followed by the IP address of the caller. Choices are:  
Enabled  
Disabled (default)  
To Configure Tunnel Modem Emulation Settings  
Using Web Manager  
To configure the Modem Emulation for a specific tunnel, click Tunnel in the menu and select  
Tunnel 1 -> Modem Emulation.  
Using the CLI  
To enter the Tunnel 1 Modem command level: enable -> tunnel 1 -> modem  
Using XML  
Include in your file: <configgroup name=”tunnel modem” instance=”1”>  
Statistics  
Tunnel statistics contains data counters, error counters, connection time and connection  
information. Statistics are available at each individual connection and aggregated across all  
connections.  
To View Tunnel Statistics  
Using Web Manager  
To view statistics for a specific tunnel, click Tunnel in the menu and select the Tunnel 1 ->  
Statistics.  
EDS-MD User Guide  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
6: Line and Tunnel Settings  
Using the CLI  
To view Tunnel 1 statistics: enable -> tunnel 1, show statistics  
Using XML  
Include in your file: <statusgroup name=”tunnel” instance=”1”>  
EDS-MD User Guide  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7: Network Settings  
The Network Settings show the status of the Ethernet interface/link and let you configure the  
settings on the device. Interface settings are related to the configuration of the IP and related  
protocols. Link settings are related to the physical link connection, which carries the IP traffic.  
The EDS-MD4, EDS-MD8 and EDS-MD16 contains one network interface. The Ethernet interface  
is also called interface 1 or eth0.  
Notes:  
Some settings require a reboot to take effect. These settings are noted below.  
Wait a minimum of 5 seconds after rebooting the unit before attempting to make any  
subsequent connections.  
The blue text in the XML command strings of this chapter are to be replaced with a  
user-specified name.  
Network Interface Settings  
Table 7-1 shows the network interface settings that can be configured.  
Table 7-1 Network Interface Settings  
Network Interface  
Settings  
Description  
BOOTP Client  
Select to turn On or Off. At boot up, after the physical link is up, the EDS-MD  
will attempt to obtain IP settings from a BOOTP server.  
Note: Overrides the configured IP address/mask, gateway, hostname, and  
domain. When DHCP is Enabled, the system automatically uses DHCP,  
regardless of whether BOOTP is Enabled. Changing this value requires you to  
reboot the device.  
DHCP Client  
Select to turn On or Off. At boot up, after the physical link is up, the EDS-MD  
will attempt to obtain IP settings from a DHCP server and will periodically renew  
these settings with the server.  
Note: Overrides BOOTP, the configured IP address/mask, gateway,  
hostname, and domain. Changing this value requires you to reboot the device.  
Note: Within WebManager, click Renew to renew the DHCP lease.  
IP Address  
Enter the static IP address to use for the interface. You may enter it alone or in  
CIDR format.  
Note: This setting will be used if Static IP is active (both DHCP and BOOTP  
are Disabled). Changing this value requires you to reboot the device. When  
DHCP or BOOTP is enabled, the EDS-MD tries to obtain an IP address from a  
DHCP or BOOTP server. If it cannot, the EDS-MD generates and uses an Auto  
IP address in the range of 169.254.xxx.xxx, with a network mask of  
255.255.0.0.  
Default Gateway  
Enter the IP address of the router for this network.  
Note: This setting will be used if Static IP is active (both DHCP and BOOTP  
are Disabled).  
EDS-MD User Guide  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
7: Network Settings  
Network Interface  
Description  
Settings (continued)  
Hostname  
Enter the hostname for the interface. It must begin with a letter or number,  
continue with a sequence of letters, numbers, or hyphens, and end with a letter  
or number.  
Note: This setting will take effect immediately, but will not register the  
hostname with a DNS server until the next reboot.  
Domain  
Enter the domain name suffix for the interface.  
Note: This setting will be used when either Static IP or Auto IP is active, or if  
DHCP/BOOTP is active and no Domain Suffix was acquired from the server.  
DHCP Client ID  
Enter the ID if the DHCP server requires a DHCP Client ID option. The DHCP  
server’s lease table shows IP addresses and MAC addresses for devices. The  
lease table shows the Client ID, in hexadecimal notation, instead of the EDS-  
MD MAC address.  
Primary DNS  
Secondary DNS  
MTU  
Enter the IP address of the primary Domain Name Server.  
Note: This setting will be used when either Static IP or Auto IP is active, or if  
DHCP/BOOTP is active and no DNS server was acquired from the server.  
Enter the IP address of the secondary Domain Name Server.  
Note: This setting will be used when either Static IP or Auto IP is active, or if  
DHCP/BOOTP is active and no DNS server was acquired from the server.  
When DHCP is enabled, the MTU size is (usually) provided with the IP address.  
When not provided by the DHCP server, or using a static configuration, this  
value is used. The MTU size can be from 576 to 1500 bytes, the default being  
1500 bytes.  
To Configure Network Interface Settings  
Using Web Manager  
To modify Ethernet (eth0) settings, click Network on the menu and select Network 1 ->  
Interface -> Configuration.  
Using the CLI  
To enter the eth0 command level: enable -> config -> if 1  
Using XML  
Include in your file: <configgroup name="interface" instance="eth0">  
To View Network Interface Status  
Using Web Manager  
In Network Interface Status, you can view both the current operational settings as well as the  
settings that would take affect upon a device reboot.  
To view Ethernet (eth0) Status, click Network on the menu and select Network 1 ->  
Interface -> Status.  
EDS-MD User Guide  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
7: Network Settings  
Network Link Settings  
Physical link parameters can be configured for an Ethernet (eth0) Network Interface (see  
Table 7-2 Network 1 (eth0) Link Settings  
Network 1 Ethernet (eth0)  
Link Settings  
Description  
Speed  
Select the Ethernet link speed. (Default is Auto)  
Auto = Auto-negotiation of Link Speed  
10 = Force 10 Mbps  
100 = Force 100 Mbps  
Duplex  
Select t he Ethernet link duplex mode. (Default is Auto)  
Auto = Auto-negotiation of Link Duplex  
Half = Force Half Duplex  
Full = Force Full Duplex  
Notes:  
When speed is Auto, duplex must be Auto or Half.  
When speed is not Auto, duplex must be Half or Full.  
Fixed speed Full duplex will produce errors connected to Auto, due to duplex  
mismatch.  
To Configure Network Link Settings  
Using Web Manager  
To modify Ethernet (eth0) Link information, click Network on the menu and select  
Network 1 -> Link.  
Using the CLI  
To enter the eth0 Link command level: enable -> config -> if 1 -> link  
Using XML  
Include in your file: <configgroup name="ethernet" instance="eth0">  
EDS-MD User Guide  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
8: Terminal and Host Settings  
Predefined connections are available via telnet, ssh, or a serial port. A user can choose one of the  
presented options and the device automatically makes the predefined connection.  
Either the Telnet, SSH, or serial port connection can present the CLI or the Login Connect Menu.  
By default, the CLI is presented when the device is accessed. When configured to present the  
Login Connect Menu, the hosts configured via the Host selections, and named serial lines are  
presented.  
Terminal Settings  
You can configure whether each serial line or the telnet/SSH server presents a CLI or a Login  
Connect menu when a connection is made.  
Table 8-1 Terminal on Network and Line Settings  
Terminal on Network  
and Line Settings  
Description  
Terminal Type  
Enter text to describe the type of terminal. The text will be sent to a host via IAC.  
Note: IAC means, “interpret as command.” It is a way to send commands over  
the network such as send break or start echoing.  
Login Connect Menu  
Exit Connect Menu  
Select the interface to display when the user logs in. Choices are:  
Enabled = shows the Login Connect Menu.  
Disabled = shows the CLI (default)  
Select whether to display a choice for the user to exit the Login Connect Menu  
and reach the CLI. Choices are:  
Enabled = a choice allows the user to exit to the CLI.  
Disabled = there is no exit to the CLI (default)  
Send Break  
Enter a Send Break control character, e.g., <control> Y, or blank to disable.  
When the Send Break control character is received from the network on its way  
to the serial line, it is not sent to the line; instead, the line output is forced to be  
inactive (the break condition).  
Note: This configuration option is only available for Line Terminals.  
Break Duration  
Echo  
Enter how long the break should last in milliseconds, up to 10000. Default is  
500.  
Note: This configuration option is only available for Line Terminals.  
Select whether to enable echo:  
Enabled  
Disabled  
Note: Applies only to Connect Mode Telnet connections, not to Accept Mode.  
Only disable Echo if your terminal echoes, in which case you will see double of  
each character typed. Default is enabled.  
EDS-MD User Guide  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
8: Terminal and Host Settings  
To Configure the Terminal Network Connection  
Using Web Manager  
To configure the Terminal on Network, click Terminal on the menu and select Network ->  
Configuration.  
Using the CLI  
To enter the Terminal Network command level: enable -> config -> terminal  
network  
Using XML  
Include in your file: <configgroup name=”terminal” instance=”network”>  
To Configure the Terminal Line Connection  
Note: The following section describes the steps to view and configure Terminal 1  
settings; these steps apply to other terminal instances of the device.  
Using Web Manager  
To configure a particular Terminal Line, click Terminal on the menu and select Line 1 ->  
Configuration.  
Using the CLI  
To enter the Terminal Line command level: enable -> config -> terminal 1  
Using XML  
Include in your file: <configgroup name=”terminal” instance=”1”>  
Host Configuration  
Table 8-2 Host Configuration  
Description  
Host Settings  
Name  
Enter a name for the host. This name appears on the Login Connect  
Menu. To leave a host out of the menu, leave this field blank.  
Protocol  
Select the protocol to use to connect to the host. Choices are:  
Telnet  
SSH  
Note: SSH keys must be loaded or created in SSH for the SSH  
protocol to work.  
EDS-MD User Guide  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
8: Terminal and Host Settings  
HostSettings(continued) Description  
SSH Username  
Enter a username to select a pre-configured Username/Password/  
Key (configured on the SSH: Client Users), or leave it blank to be  
prompted for a username and password at connect time.  
Note: This field appears if you selected SSH as the protocol.  
Enter an IP address for the host to which the device will connect.  
Enter the port on the host to which the device will connect.  
Remote Address  
Remote Port  
To Configure Host Settings  
Note: The following section describes the steps to view and configure Host 1 settings;  
these steps apply to other host instances of the device.  
Using Web Manager  
To configure a particular Host, click Host on the menu and select Host 1 -> Configuration.  
Using the CLI  
To enter the Host command level: enable -> config -> host 1  
Using XML  
Include in your file: <configgroup name=”host” instance=”1”>  
EDS-MD User Guide  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
9: Services Settings  
DNS Settings  
This section describes the active run-time settings for the domain name system (DNS) protocol.  
The primary and secondary DNS addresses come from the active interface. The static addresses  
from the Network Interface configuration settings may be overridden by DHCP.  
Note: The blue text in the XML command strings of this chapter are to be replaced with  
a user-specified name.  
Table 9-1 DNS Settings  
Setting / Field  
Lookup  
Description  
Perform one of the following:  
Enter an IP address, and perform a reverse Lookup to locate the hostname for  
that IP address  
Enter a hostname, and perform a forward Lookup to locate the corresponding IP  
address  
To View or Configure DNS Settings:  
Using Web Manager  
To view DNS current status, click DNS in the menu.  
To lookup DNS name or IP address, click DNS in the menu to access the Lookup field.  
Note: To configure DNS for cases where it is not supplied by a protocol, click Network  
in the menu and select Interface -> Configuration.  
Using the CLI  
To enter the DNS command level: enable -> dns  
Using XML  
Include in your file: <configgroup name=”interface” instance=”eth0”>  
EDS-MD User Guide  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
9: Services Settings  
FTP Settings  
The FTP protocol can be used to upload and download user files, and upgrade the EDS-MD4/8/16  
firmware. A configurable option is provided to enable or disable access via this protocol.  
Table 9-2 FTP Settings  
FTP Settings  
State  
Description  
Select to enable or disable the FTP server:  
Enabled (default)  
Disabled  
To Configure FTP Settings  
Using Web Manager  
To configure FTP, click FTP in the menu.  
Using the CLI  
To enter the FTP command level: enable -> config -> ftp  
Using XML  
Include in your file: <configgroup name=”ftp server”>  
Syslog Settings  
The Syslog information shows the current configuration and statistics of the syslog. Here you can  
configure the syslog host and the severity of the events to log.  
Note: The system log is always saved to local storage, but it is not retained through  
reboots unless diagnostics logging to the filesystem is enabled. Saving the system log to a  
server that supports remote logging services (see RFC 3164) allows the administrator to  
save the complete system log history. The default port is 514.  
Table 9-3 Syslog Settings  
Syslog Settings  
State  
Description  
Select to enable or disable the syslog:  
Enabled  
Disabled (default)  
Host  
Enter the IP address of the remote server to which system logs are sent for  
storage.  
Remote Port  
Enter the number of the port on the remote server that supports logging  
services. The default is 514.  
EDS-MD User Guide  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
9: Services Settings  
Syslog Settings  
(continued)  
Description  
Severity Log Level  
Specify the minimum level of system message the EDS-MD should log. This  
setting applies to all syslog facilities. The drop-down list in the Web Manager is  
in descending order of severity (e.g., Emergency is more severe than Alert.)  
To View or Configure Syslog Settings:  
Using Web Manager  
To configure the Syslog, click Syslog in the menu.  
Using the CLI  
To enter the Syslog command level: enable -> config -> syslog  
Using XML  
Include in your file: <configgroup name=”syslog”>  
HTTP Settings  
Hypertext Transfer Protocol (HTTP) is the transport protocol for communicating hypertext  
documents on the Internet. HTTP defines how messages are formatted and transmitted. It also  
defines the actions web servers and browsers should take in response to different commands.  
HTTP Authentication enables the requirement of usernames and passwords for access to the  
device.  
Table 9-4 HTTP Settings  
HTTP Settings  
State  
Description  
Select to enable or disable the HTTP server:  
Enabled (default)  
Disabled  
Port  
Enter the port for the HTTP server to use. The default is 80.  
Secure Port  
Enter the port for the HTTPS server to use. The default is 443. The HTTP  
server only listens on the HTTPS Port when an SSL certificate is configured.  
Secure Protocols  
Select to enable or disable the following protocols:  
SSL3 = Secure Sockets Layer version 3  
TLS1.0 = Transport Layer Security version 1.0. TLS 1.0 is the successor of  
SSL3 as defined by the IETF.  
TLS1.1 = Transport Layer Security version 1.1  
The protocols are enabled by default.  
Note: A server certificate and associated private key need to be installed in  
the SSL configuration section to use HTTPS.  
Secure Credentials  
Specify the name of the set of RSA and/or DSA certificates and keys to be  
used for the secure connection.  
EDS-MD User Guide  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
9: Services Settings  
HTTP Settings (continued) Description  
Max Timeout  
Enter the maximum time for the HTTP server to wait when receiving a  
request. This prevents Denial-of-Service (DoS) attacks. The default is 10  
seconds.  
Max Bytes  
Enter the maximum number of bytes the HTTP server accepts when receiving  
a request. The default is 40 KB (this prevents DoS attacks).  
Logging State  
Select to enable or disable HTTP server logging:  
Enabled (default)  
Disabled  
Max Log Entries  
Log Format  
Set the maximum number of HTTP server log entries. Only the last Max Log  
Entries are cached and viewable.  
Set the log format string for the HTTP server. Follow these Log Format rules:  
%a - remote IP address (could be a proxy)  
%b - bytes sent excluding headers  
%B - bytes sent excluding headers (0 = '-')  
%h - remote host (same as '%a')  
%{h}i - header contents from request (h = header string)  
%m - request method  
%p - ephemeral local port value used for request  
%q - query string (prepend with '?' or empty '-')  
%t - timestamp HH:MM:SS (same as Apache '%(%H:%M:%S)t' or  
'%(%T)t')  
%u - remote user (could be bogus for 401 status)  
%U - URL path info  
%r - first line of request (same as '%m %U%q <version>')  
%s - return status  
Authentication Timeout  
The timeout period applies if the selected authentication type is either Digest  
or SSL/Digest. After this period of inactivity, the client must authenticate  
again.  
To Configure HTTP Settings  
Using Web Manager  
To configure HTTP settings, click HTTP in the menu and select Configuration.  
To view HTTP statistics, click HTTP in the menu and select Statistics.  
Using the CLI  
To enter the HTTP command level: enable -> config -> http  
Using XML  
Include in your file: <configgroup name=”http server”>  
Table 9-5 HTTP Authentication Settings  
HTTP Authentication Settings  
URI  
Description  
Enter the Uniform Resource Identifier (URI).  
Note: The URI must begin with ‘/’ to refer to the filesystem.  
EDS-MD User Guide  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
9: Services Settings  
HTTP Authentication Settings  
Auth Type  
Description  
Select the authentication type:  
None = no authentication is necessary.  
Basic = encodes passwords using Base64.  
Digest = encodes passwords using MD5.  
SSL = can only be accessed over SSL (no password is required).  
SSL/Basic = is accessible only over SSL and encodes passwords  
using Base64.  
SSL/Digest = is accessible only over SSL and encodes passwords  
using MD5.  
Note: When changing the parameters of Digest or SSL Digest  
authentication, it is often best to close and reopen the browser to  
ensure it does not attempt to use cached authentication information.  
To Configure HTTP Authentication  
Using Web Manager  
To configure HTTP Authentication, click HTTP in the menu and select Authentication.  
Using the CLI  
To enter the HTTP command level: enable -> config -> http  
Using XML  
Include in your file: <configgroup name=”http authentication uri”  
instance=”uri name”>  
RSS Settings  
Really Simple Syndication (RSS) (sometimes referred to as Rich Site Summary) is a method of  
feeding online content to Web users. Instead of actively searching for configuration changes, RSS  
feeds permit viewing only relevant and new information regarding changes made to the via an  
RSS publisher. The RSS feeds may also be stored to the file system cfg_log.txt file.  
Table 9-6 RSS Settings  
RSS Settings  
RSS Feed  
Description  
Select On or Off for RSS feeds to an RSS publisher. The default setting is off.  
Persistent  
Select On or Off for RSS feed to be written to a file (cfg_log.txt) and to be available  
across reboots. The default setting is off.  
Max Entries  
Set the maximum number of log entries. Only the last Max Entries are cached and  
viewable.  
To Configure RSS Settings  
Using Web Manager  
To configure RSS, click RSS in the menu.  
EDS-MD User Guide  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
9: Services Settings  
Using the CLI  
To enter the RSS command level: enable -> config -> rss  
Using XML  
Include in your file: <configgroup name=”rss”>  
Real Time Clock (RTC) Settings  
The current date and time displayed on the EDS-MD can be modified.  
Table 9-7 RTC Settings  
RTC Settings  
Time Zone  
Date  
Description  
Select the time zone corresponding to the location of the EDS-MD.  
Select the year, month and day corresponding to the current date at the location of  
the EDS-MD  
Time (24 hour)  
Select the hour, minutes and seconds corresponding to the current time at the  
location of the EDS-MD.  
To Configure RTC Settings  
Using Web Manager  
To configure RTC, click RTC in the menu.  
Using the CLI  
To enter the RTC command level: enable -> config -> rtc  
Using XML  
Include in your file: <configgroup name=”clock”>  
EDS-MD User Guide  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
10: Security Settings  
The EDS-MD4, EDS-MD8 and EDS-MD16 device supports Secure Shell (SSH) and Secure  
Sockets Layer (SSL). SSH is a network protocol for securely accessing a remote device. SSH  
provides a secure, encrypted communication channel between two hosts over a network. It  
provides authentication and message integrity services.  
Secure Sockets Layer (SSL) is a protocol that manages data transmission security over the  
Internet. It uses digital certificates for authentication and cryptography against eavesdropping and  
tampering. It provides encryption and message integrity services. SSL is widely used for secure  
communication to a web server. SSL uses certificates and private keys.  
Note: The device supports SSLv3 and its successors, TLS1.0 and TLS1.1. An incoming  
SSLv2 connection attempt is answered with an SSLv3 response. If the initiator also  
supports SSLv3, SSLv3 handles the rest of the connection.  
SSH Settings  
SSH is a network protocol for securely accessing a remote device over an encrypted channel. This  
protocol manages the security of internet data transmission between two hosts over a network by  
providing encryption, authentication, and message integrity services.  
Two instances require configuration: when the EDS-MD is the SSH server and when it is an SSH  
client. The SSH server is used by the CLI (Command Mode) and for tunneling in Accept Mode.  
The SSH client is for tunneling in Connect Mode.  
To configure the EDS-MD as an SSH server, there are two requirements:  
Defined Host Keys: both private and public keys are required. These keys are used for the  
Diffie-Hellman key exchange (used for the underlying encryption protocol).  
Defined Users: these users are permitted to connect to the EDS-MD SSH server.  
SSH Server Host Keys  
The SSH Server Host Keys are used by all applications that play the role of an SSH Server.  
Specifically Tunneling in Accept Mode. These keys can be created elsewhere and uploaded to the  
device or automatically generated on the device.  
If uploading existing keys, take care to ensure the Private Key will not be compromised in transit.  
This implies the data is uploaded over some kind of secure private network.  
Note: Some SSH Clients require RSA Host Keys to be at least 1024 bits in size.  
Table 10-1 SSH Server Host Keys  
RSS Settings  
Private Key  
Description  
Enter the path and name of the existing private key you want to upload. . In  
WebManager, you can also Browse to the private key to be uploaded. Be sure the  
private key will not be compromised in transit. This implies the data is uploaded over  
some kind of secure private network.  
EDS-MD User Guide  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
10: Security Settings  
RSS Settings  
(continued)  
Description  
Public Key  
Enter the path and name of the existing public key you want to upload. In  
WebManager, you can also Browse to the public key to be uploaded.  
Key Type  
Select a key type to use for the new key:  
RSA  
DSA  
Bit Size  
Select a bit length for the new key:  
512  
768  
1024  
Note: SSH Keys from other programs may be converted to the required EDS-MD  
format. Use Open SSH to perform the conversion.  
SSH Client Known Hosts  
The SSH Client Known Hosts are used by all applications that play the role of an SSH Client.  
Specifically Tunneling in Connect Mode. Configuring these public keys are optional but if they exist  
another layer of security is offered which helps prevent Man-in-the-Middle (MITM) attacks.  
Table 10-2 SSH Client Known Hosts  
RSS Settings  
Server  
Description  
Specify either a DNS Hostname or IP Address when adding public host keys for a  
Server. This Server name should match the name used as the Remote Address in  
Connect Mode Tunneling.  
Public RSA Key  
Public DSA Key  
Enter the path and name of the existing public RSA key you want to use with this  
user. In WebManager, you can also Browse to the public RSA key to be uploaded. If  
authentication is successful with the key, no password is required.  
Enter the path and name of the existing public DSA key you want to use with this  
user. In WebManager, you can also Browse to the public DSA key to be uploaded.If  
authentication is successful with the key, no password is required.  
Note: These settings are not required for communication. They protect against Man-In-  
The-Middle (MITM) attacks.  
SSH Server Authorized Users  
The SSH Server Authorized Users are used by all applications that play the role of an SSH Server  
and specifically Tunneling in Accept Mode. Every user account must have a Password.  
The user's Public Keys are optional and only necessary if public key authentication is wanted.  
Using public key authentication will allow a connection to be made without the password being  
asked at that time.  
Note: When uploading the security keys, ensure the keys are not compromised in  
transit.  
EDS-MD User Guide  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
10: Security Settings  
Table 10-3 SSH Server Authorized Users  
Description  
RSS Settings  
Username  
Enter a new username or edit an existing one.  
Enter a new password or edit an existing one.  
Password  
Public RSA Key  
Enter the path and name of the existing public RSA key you want to use with this  
user. In WebManager, you can also Browse to the public RSA key to be uploaded. If  
authentication is successful with the key, no password is required.  
Public DSA Key  
Enter the path and name of the existing public DSA key you want to use with this  
user. In WebManager, you can also Browse to the public DSA key to be uploaded.If  
authentication is successful with the key, no password is required.  
SSH Client Users  
The SSH Client Users are used by all applications that play the role of an SSH Client. Specifically  
Tunneling in Connect Mode. To configure the EDS-MD as an SSH client, an SSH client user must  
be both configured and also exist on the remote SSH server.  
At the very least, a Password or Key Pair must be configured for a user. The keys for public key  
authentication can be created elsewhere and uploaded to the device or automatically generated  
on the device.  
If uploading existing Keys, take care to ensure the Private Key will not be compromised in transit.  
This implies the data is uploaded over some kind of secure private network.  
The default Remote Command is '<Default login shell>' which tells the SSH Server to execute a  
remote shell upon connection. This can be changed to anything the SSH Server on the remote  
host can execute.  
Note: If you are providing a key by uploading a file, make sure that the key is not  
password protected.  
Table 10-4 SSH Client Users  
RSS Settings  
Description  
Username  
Password  
Enter the name that the device uses to connect to an SSH server.  
Enter the password associated with the username.  
Remote Command Enter the command that can be excuted remotely. Default is shell, which tells the  
SSH server to execute a remote shell upon connection. This command can be  
changed to anything the remote host can perform.  
Private Key  
Enter the path and name of the existing private key you want to upload. . In  
WebManager, you can also Browse to the private key to be uploaded. Be sure the  
private key will not be compromised in transit. This implies the data is uploaded over  
some kind of secure private network.  
Public Key  
Key Type  
Enter the path and name of the existing public key you want to upload. In  
WebManager, you can also Browse to the public key to be uploaded.  
Select a bit length for the key:  
RSA  
DSA  
EDS-MD User Guide  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
10: Security Settings  
RSS Settings  
(continued)  
Description  
Bit Size  
Select the bit length of the new key:  
512  
768  
1024  
Using a larger Bit Size takes more time to generate the key. Approximate times are:  
1 second for a 512 bit RSA key  
1 second for a 768 bit RSA key  
1 second for a 1024 bit RSA key  
2 seconds for a 512 bit DSA key  
2 seconds for a 768 bit DSA key  
20 seconds for a 1024 bit DSA key  
Note: Some SSH clients require RSA host keys to be at least 1024 bits long. This  
device generates keys up to 2048 bits long.  
To Configure SSH Settings  
Using Web Manager  
To configure SSH, click SSH in the menu.  
Using the CLI  
To enter the SSH command level: enable -> ssh  
Using XML  
Include in your file: <configitem name=”ssh username”>  
SSL Settings  
Secure Sockets Layer (SSL) is a protocol for managing the security of data transmission over the  
Internet. It provides encryption, authentication, and message integrity services. SSL is widely used  
for secure communication to a web server.  
Certificate/Private key combinations can be obtained from an external Certificate Authority (CA)  
and uploaded into the unit. Self-signed certificates with associated private key can be generated  
by the device server itself.  
Note: The blue text in the XML command strings of this chapter are to be replaced with  
a user-specified name.  
EDS-MD User Guide  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
10: Security Settings  
Certificate and Key Generation  
The EDS-MD4, EDS-MD8 and EDS-MD16 can generate self signed certificates and their  
corresponding keys. This can be done for both the rsa and dsa certificate formats. Certificates can  
be identified on the EDS-MD4/8/16 by a name provided at generation time.  
Table 10-5 Certificate and Key Generation Settings  
Certificate Generation  
Settings  
Description  
Country (2 Letter Code)  
Enter the 2-letter country code to be assigned to the new self-signed  
certificate.  
Examples: US for United States and CA for Canada  
State/Province  
Locality (City)  
Organization  
Enter the state or province to be assigned to the new self-signed certificate.  
Enter the city or locality to be assigned to the new self-signed certificate.  
Enter the organization to be associated with the new self-signed certificate.  
Organization Unit  
Enter the organizational unit to be associated with the new self-signed  
certificate.  
Common Name  
Expires  
Enter the common name to be associated with the new self signed  
certificate. Note that this is a required field.  
Enter the expiration date, in mm/dd/yyyy format, for the new self-signed  
certificate.  
Example: An expiration date of May 9, 2012 is entered as 05/09/2012.  
Select the bit size of the new self-signed certificate. Choices are:  
Key length  
512 bits  
768 bits  
1024 bits  
2048 bits  
The larger the bit size, the longer it takes to generate the key.  
Select the type of key:  
Type  
RSA = Public-Key Cryptography algorithm based on large prime  
numbers, invented by Rivest Shamir and Adleman. Used for encryption  
and signing.  
DSA = Digital Signature Algorithm also based on large prime numbers,  
but can only be used for signing. Developed by the US government to  
avoid the patents on RSA.  
To Create a New Credential  
Using Web Manager  
To create a new credential, click SSL in the menu and select Credentials.  
Using the CLI  
To enter the SSL command level: enable -> ssl  
To enter the Credentials command level: enable -> ssl -> credentials  
EDS-MD User Guide  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
10: Security Settings  
Using XML  
Not applicable.  
Certificate Upload Settings  
SSL certificates identify the EDS-MD4/8/16 to peers. Certificate and key pairs can be uploaded to  
the EDS-MD4/8/16 through either the CLI or XML import mechanisms. Certificates can be  
identified on the EDS-MD4/8/16 by a name provided at upload time.  
Table 10-6 Upload Certificate Settings  
Upload  
Description  
Certificate  
Settings  
New Certificate  
SSL certificate to be uploaded.  
RSA or DSA certificates are allowed.  
The format of the certificate must be PEM. It must start with “-----BEGIN  
CERTIFICATE-----“ and end with “-----END CERTIFICATE-----“. Some  
Certificate Authorities add comments before and/or after these lines. Those need to be  
deleted before upload.  
New Private Key  
The key needs to belong to the certificate entered above.  
The format of the file must be PEM. It must start with “-----BEGIN RSA  
PRIVATE KEY-----” and end with “-----END RSA PRIVATE KEY-----”.  
Read DSA instead of RSA in case of a DSA key. Some Certificate Authorities add  
comments before and/or after these lines. Those need to be deleted before upload.  
To Configure an Existing SSL Credential  
Using Web Manager  
To configure an existing SSL Credential, click SSL in the menu and select Credentials.  
Using the CLI  
To enter the SSL command level: enable -> ssl  
To enter the Credential command level: enable -> ssl -> credentials  
Using XML  
Include in your file:  
<configgroup name=”ssl”>  
and <configitem name=”credentials” instance=”name”>  
and <value name="RSA certificate"/> or <value name="DSA certificate"/>  
EDS-MD User Guide  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
10: Security Settings  
Trusted Authorities  
One or more authority certificates are needed to verify a peer's identity. These certificates do not  
require a private key.  
Table 10-7 Trusted Authority Settings  
Trusted Authorities  
Settings  
Description  
Authority  
SSL authority certificate.  
RSA or DSA certificates are allowed.  
The format of the authority certificate can be PEM or PKCS7. PEM files  
must start with “-----BEGIN CERTIFICATE-----” and end with “---  
--END CERTIFICATE-----”. Some Certificate Authorities add  
comments before and/or after these lines. Those need to be deleted  
before upload.  
To Upload an Authority Certificate  
Using Web Manager  
To upload an Authority Certificate, click SSL in the menu and select Trusted Authorities.  
Using the CLI  
To enter the SSL command level: enable -> ssl  
To enter the Trusted Authorities command level: enable -> ssl -> trusted  
authorities  
Using XML  
Include in your file:  
<configgroup name=”ssl”>  
and <configitem name=”trusted authority” instance =”1”>  
and <configitem name=”intermediate authority” instance=”1”>  
EDS-MD User Guide  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
11: Maintenance and Diagnostics Settings  
Filesystem Settings  
Use the file system to list, view, add, remove, and transfer files. The EDS-MD4/8/16 uses an EXT3  
flash file system to store files. This is a journalled file system, which means that changes to the file  
system are recorded before the actual changes themselves are made. In the event of power loss,  
the use of journaling can usually recover from changes that had been started but not completed.  
Some file systems may contain a 'lost+found' directory. In the event of power loss in the midst of  
file system I/O, file data that cannot be fully recovered will be placed in this directory. It is  
recommended to always restart the system from the Web Manager application or the CLI.  
Note: It is recommended to always use the Web Manager application or the CLI to  
shutdown/restart the system.  
File Display  
It is possible to view the list of existing files, and to view their contents in the ASCII or hexadecimal  
formats.  
Table 11-1 File Display Settings  
File Display Commands  
ls  
Description  
Displays a list of files on the EDS-MD, and their respective sizes.  
cat  
Displays the specified file in ASCII format.  
dump  
Displays the specified file in a combination of hexadecimal and ASCII  
formats.  
pwd  
Print working directory.  
Change directories.  
cd  
show tree  
Display file/directory tree.  
To Display Files  
Using Web Manager  
To view existing files and file contents, click FIlesystem in the menu and select Browse.  
Using the CLI  
To enter the Filesystem command level: enable -> filesystem  
Using XML  
Not applicable.  
EDS-MD User Guide  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
11: Maintenance and Diagnostics Settings  
File Modification  
The EDS-MD4/8/16 allows for the creation and removal of files on its filesystem.  
Table 11-2 File Modification Settings  
File Modification  
Commands  
Description  
rm  
Removes the specified file from the file system.  
Creates the specified file as an empty file.  
Creates a copy of a file.  
touch  
cp  
mkdir  
rmdir  
format  
Creates a directory on the file system.  
Removes a directory from the file system.  
Format the file system and remove all data.  
File Transfer  
Files can be transferred to and from the EDS-MD4/8/16 via the TFTP protocol. This can be useful  
for saving and restoring XML configuration files. Files can also be uploaded via HTTP.  
Table 11-3 File Transfer Settings  
File Transfer Settings  
Create  
Description  
Browse to location of the file to be created.  
Upload File  
Copy File  
Move  
Browse to location of the file to be uploaded.  
Enter the source and destination for file to be copied.  
Enter the source and destination for file to be moved.  
Action  
Select the action that is to be performed via TFTP:  
Get = a “get” command will be executed to store a file locally.  
Put = a “put” command will be executed to send a file to a remote location.  
Local File  
Enter the name of the local file on which the specified “get” or “put” action is  
to be performed.  
Remote File  
Enter the name of the file at the remote location that is to be stored locally  
(“get’) or externally (“put”).  
Host  
Port  
Enter the IP address or name of the host involved in this operation.  
Enter the number of the port involved in TFTP operations.  
EDS-MD User Guide  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
11: Maintenance and Diagnostics Settings  
To Transfer or Modify Filesystem Files  
Using Web Manager  
To create a new file or directory, upload an existing file, copy or move a file, click Filesystem  
in the menu and select Browse.  
Using the CLI  
To enter the Filesystem command level: enable -> filesystem  
Using XML  
Not applicable.  
IP Network Stack Settings  
There are various low level network stack specific items that are available for configuration. This  
includes settings related to IP, ICMP, ARP and SMTP, which are described in the sections below.  
Table 11-4 IP Network Stack Settings  
Protocol Stack  
IP Settings  
Description  
IP Time to Live  
This value typically fills the Time To Live in the IP header. SNMP refers to this  
value as "ipDefaultTTL".  
Enter the number of hops to be transmitted before the packet is discarded.  
Multicast Time to Live This value fills the Time To Live in any multicast IP header. Normally this value  
will be one so the packet will be blocked at the first router. It is the number of  
hops allowed before a Multicast packet is discarded.  
Enter the value to be greater than one to intentionally propagate multicast  
packets to additional routers.  
To Configure IP Network Stack Settings  
Using Web Manager  
To configure IP protocol settings, click Protocol Stack in the menu and select IP.  
Using the CLI  
To enter the command level: enable -> config -> ip  
Using XML  
Include in your file: <configgroup name=”ip”>  
EDS-MD User Guide  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
11: Maintenance and Diagnostics Settings  
Table 11-5 ICMP Network Stack Settings  
Protocol Stack  
ICMP Settings  
Description  
State  
The State selection is used to turn on/off processing of ICMP messages.  
This includes both incoming and outgoing messages. Choose Enabled or  
Disabled.  
To Configure ICMP Network Stack Settings  
Using Web Manager  
To configure ICMP protocol settings, click Protocol Stack in the menu and select ICMP.  
Using the CLI  
To enter the command level: enable -> config -> icmp  
Using XML  
Include in your file: <configgroup name=”icmp”>  
Table 11-6 ARP Network Stack Settings  
Protocol Stack  
Description  
ARP Settings  
IP Address  
Enter the IP address to add to the ARP cache.  
Enter the MAC address to add to the ARP cache.  
MAC Address  
To Configure ARP Network Stack Settings  
Using Web Manager  
To configure ARP protocol settings, click Protocol Stack in the menu and select ARP.  
Using the CLI  
To enter the command level: enable -> config -> arp  
Using XML  
Include in your file: <configgroup name=”arp”>  
EDS-MD User Guide  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
11: Maintenance and Diagnostics Settings  
Table 11-7 SMTP Network Stack Settings  
Protocol Stack SMTP  
Settings  
Description  
Relay Address  
Address of all outbound email messages through a mail server. Can contain  
either a hostname or an IP address.  
Relay Port  
Port utilized for the delivery of outbound email messages.  
To Configure SMTP Network Stack Settings  
Using Web Manager  
To configure SMTP protocol settings, click Protocol Stack in the menu and select SMTP.  
Using the CLI  
To enter the command level: enable -> config -> smtp  
Using XML  
Include in your file: <configgroup name=”smtp”>  
Query Port  
The query port (UDP port 0x77FE) is used for the automatic discovery of the device by the  
DeviceInstaller utility. Only 0x77FE discover messages from DeviceInstaller are supported. For  
more information on DeviceInstaller, see Chapter 4: Using DeviceInstaller on page 28.  
Table 11-8 Query Port Settings  
Query Port Settings  
Query Port Server  
Description  
Enables or disables listening and responding to query port  
messages. Select On or Off.  
To Configure Query Port Settings  
Using Web Manager  
To view Query Port settings or to switch the Query Port Server on or off, click Query Port in  
the menu.  
Using the CLI  
To enter the Query Port command level: enable -> config -> query port  
EDS-MD User Guide  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
11: Maintenance and Diagnostics Settings  
Using XML  
Include in your file:  
<configgroup name=”query port”>  
and  
<configitem name=”state”>  
Diagnostics  
The EDS-MD4/8/16 has several tools for diagnostics and statistics. Various options allow for the  
configuration or viewing of IP socket information, ping, traceroute, memory, and processes.  
Hardware  
To View Hardware Information  
Using Web Manager  
To view hardware information, click Diagnostics in the menu and select Hardware.  
Using the CLI  
To enter the command level: enable -> device, show hardware information  
Using XML  
Include in your file: <statusgroup name=”hardware”>  
IP Sockets  
You can view the list of listening and connected IP sockets.  
To View the List of IP Sockets  
Using Web Manager  
To view IP Sockets, click Diagnostics in the menu and select IP Sockets.  
Using the CLI  
To enter the command level: enable, show ip sockets  
Using XML  
Include in your file: <statusgroup name=”ip sockets”>  
Ping  
The ping command can be used to test connectivity to a remote host.  
EDS-MD User Guide  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                           
11: Maintenance and Diagnostics Settings  
Table 11-9 Ping Settings  
Diagnostics: Ping Settings  
Description  
Host  
Enter the IP address or host name for the EDS-MD to ping.  
Count  
Enter the number of ping packets EDS-MD should attempt to send to the  
Host. The default is 5.  
Timeout  
Enter the time, in seconds, for the EDS-MD to wait for a response from  
the host before timing out. The default is 5 seconds.  
To Ping a Remote Host  
Using Web Manager  
To ping a Remote Host, click Diagnostics in the menu and select Ping.  
Using the CLI  
To enter the command level: enable  
Using XML  
Not applicable.  
Traceroute  
Here you can trace a packet from the EDS-MD4/8/16 to an Internet host, showing how many hops  
the packet requires to reach the host and how long each hop takes. If you visit a web site whose  
pages appear slowly, you can use traceroute to determine where the longest delays are occurring.  
Table 11-10 Traceroute Settings  
Diagnostics:  
Description  
Traceroute Settings  
Host  
Enter the IP address or DNS hostname. This address is used to show the path  
between it and the EDS-MD when issuing the traceroute command.  
To Perform a Traceroute  
Using Web Manager  
To perform a Traceroute, click Diagnostics in the menu and select Traceroute.  
Using the CLI  
To enter the command level: enable  
Using XML  
Not applicable.  
EDS-MD User Guide  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
11: Maintenance and Diagnostics Settings  
Log  
Table 11-11 Log Settings  
Description  
Diagnostics: Log  
Output  
Select a diagnostic log output type:  
Disable - Turn off the loggin feature.  
Filesystem - Directs logging to /log.txt.  
Line (1, 2, 3 and 4) - Directs logging to the selected serial line.  
Max Length  
Set the maximum length of the log.txt file.  
Note: This setting becomes available when Filesystem is selected.  
To Configure the Diagnostic Log Output  
Using Web Manager  
To configure the Diagnostic Log output, click Diagnostics in the menu and select Log.  
Using the CLI  
To enter the command level: enable -> config -> diagnostics -> log  
Using XML  
Include in your file:  
<configgroup name=”diagnostics”>  
and  
<configitem name=”log”>  
Memory  
The memory information shows the total, used, and available memory (in kilobytes).  
To View Memory Usage  
Using Web Manager  
To view memory information, click Diagnostics in the menu and select Memory.  
Using the CLI  
To enter the command level: enable -> device, show memory  
Using XML  
Include in your file: <statusgroup name=”memory”>  
EDS-MD User Guide  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
11: Maintenance and Diagnostics Settings  
Processes  
The EDS-MD4/8/16 Processes information shows all the processes currently running on the  
system. It shows the Process ID (PID), Parent Process ID (PPID), user, CPU percentage,  
percentage of total CPU cycles, and process command line information.  
To View Process Information  
Using Web Manager  
To view process information, click Diagnostics in the menu and select Processes.  
Using the CLI  
To enter the command level: enable, show processes  
Using XML  
Include in your file: <statusgroup name=”processes”>  
Threads  
The EDS-MD4/8/16 Threads information shows details of threads in the ltrx_evo task which can  
be useful for technical experts in debugging.  
To View Thread Information  
Using Web Manager  
To view thread information, click Diagnostics in the menu and select Threads.  
Using the CLI  
To enter the command level: enable -> device, show task state  
Using XML  
Not available  
EDS-MD User Guide  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
11: Maintenance and Diagnostics Settings  
System Settings  
The EDS-MD4/8/16 System settings allow for rebooting the device, restoring factory defaults,  
uploading new firmware and updating a system’s short and long name.  
Note: Anytime you reboot the unit, this operation will take some time to complete.  
Please wait a minimum of 5 seconds after rebooting the unit before attempting to make  
any subsequent connections.  
Table 11-12 System Settings  
System Settings  
Description  
Reboots the device.  
Reboot Device  
Restores the device to the original factory settings. All configuration will be  
lost. The EDS-MD automatically reboots upon setting back to the defaults.  
Restore Factory Defaults  
FTP to the EDS-MD. Write the new firmware file to firmware.rom on the  
EDS-MD. The device automatically reboots upon the installation of new  
firmware. See the section, FTP Settings on page 53.  
Upload New Firmware  
Short Name  
Long Name  
Enter a short name for the system name. A maximum of 32 characters are  
allowed.  
Enter a long name for the system name. A maximum of 64 characters are  
allowed.  
To Reboot or Restore Factory Defaults  
Using Web Manager  
To access the area with options to reboot, restore to factory defaults, upload new firmware,  
update the system name (long or short names) or to view the current configuration, click  
System in the menu.  
Using the CLI  
To enter the command level: enable  
Using XML  
Include in your file: <configgroup name=”xml import control”>  
EDS-MD User Guide  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
12: Advanced Settings  
Email Settings  
View and configure email alerts relating to events occurring within the system.  
Table 12-1 Email Configuration  
Email – Configuration  
Settings  
Description  
To  
Enter the email address to which the email alerts will be sent. Multiple  
addresses are separated by semicolon (;). Required field if an email is to be  
sent.  
CC  
Enter the email address to which the email alerts will be copied. Multiple  
addresses are separated by semicolon (;).  
From  
Enter the email address to list in the From field of the email alert. Required  
field if an email is to be sent.  
Reply-To  
Enter the email address to list in the Reply-To field of the email alert.  
Enter the subject for the email alert.  
Subject  
Message File  
Enter the path of the file to send with the email alert. This file appears within  
the message body of the email.  
Overriding Domain  
Enter the domain name to override the current domain name in EHLO  
(Extended Hello).  
Server Port  
Local Port  
Enter the SMTP server port number. The default is port 25.  
Enter the local port to use for email alerts. The default is a random port  
number.  
Priority  
Select the priority level for the email alert:  
Urgent  
High  
Normal  
Low  
Very Low  
To View, Configure and Send Email  
Note: The following section describes the steps to view and configure Email 1 settings;  
these steps apply to other emails available for the device.  
Using Web Manager  
To view Email statistics, click Email in the menu and select Email 1 -> Statistics.  
To configure basic Email settings, click Email in the menu and select Email 1 ->  
Configuration.  
To send an email, click Email in the menu and select Email 1 -> Send Email.  
EDS-MD User Guide  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
12: Advanced Settings  
Using the CLI  
To enter Email command level: enable -> email 1  
Using XML  
Include in your file: <configgroup name=”email” instance=”1”>  
Command Line Interface Settings  
The Command Line Interface settings allow you to control how users connect to and interact with  
the EDS-MD4/8/16's command line. It is possible to configure access via the Telnet and SSH  
protocols, in addition to general CLI options.  
Basic CLI Settings  
The basic CLI settings control general CLI access and usability options.  
Table 12-2 CLI Configuration Settings  
Command Line Interface  
Configuration Settings  
Description  
Login Password  
Enter the password for logins by the admin account. The default password is  
“PASS”.  
Enable Level Password  
Quit Connect Line  
Enter the password for access to the Command Mode Enable level. There is  
no password by default.  
Set the string used to terminate a connect line session and resume the CLI.  
Type <control> before any key to be pressed while holding down the Ctrl key,  
for example, <control>L.  
Inactivity Timeout  
Line Authentication  
Set a time period in which the CLI session should disconnect if no data is  
received. Enter 0 to disable. Blank the display field to restore the default.  
Enable or Disable authentication for CLI access on the serial lines.  
To View and Configure Basic CLI Settings  
Using Web Manager  
To view CLI statistics, click CLI in the menu and select Statistics.  
To configure basic CLI settings, click CLI in the menu and select Configuration.  
Using the CLI  
To enter CLI command level: enable -> config -> cli  
Using XML  
Include in your file: <configgroup name=”cli”>  
EDS-MD User Guide  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
12: Advanced Settings  
Telnet Settings  
The telnet settings control CLI access to the EDS-MD4/8/16 over the Telnet protocol.  
Table 12-3 Telnet Settings  
Telnet Settings  
Description  
Telnet State  
Telnet Port  
Enable or Disable CLI access via telnet  
Enter an alternative Telnet Port to override the default used by the CLI  
server. Blank the field to restore the default.  
Telnet Max Sessions  
Telnet Authentication  
Specify the maximum number of concurrent Telnet sessions that will be  
allowed.  
Enable or Disable authentication for telnet logins.  
To Configure Telnet Settings  
Using Web Manager  
To configure Telnet settings, click CLI in the menu and select Configuration.  
Using the CLI  
To enter the Telnet command level: enable -> config -> cli -> telnet  
Using XML  
Include in your file:  
<configgroup name=”telnet”>  
and  
<configitem name=”state”>  
and  
<configitem name=”authentication”>  
SSH Settings  
The SSH settings control CLI access to the EDS-MD4/8/16 over the SSH protocol.  
Table 12-4 SSH Settings  
SSH Settings  
SSH State  
Description  
Select to Enable or Disable CLI access via telnet.  
SSH Port  
Specify the SSH Port and override the default, as needed. Blank the field  
to restore the default.  
SSH Max Sessions  
Specify the maximum number of concurrent SSH sessions that will be  
allowed.  
EDS-MD User Guide  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
12: Advanced Settings  
To Configure SSH Settings  
Using Web Manager  
To configure SSH settings, click CLI in the menu and select Configuration.  
Using the CLI  
To enter the SSH command level: enable -> config -> cli -> ssh  
Using XML  
Include in your file:  
<configgroup name=”ssh”>  
and  
<configitem name=”state”>  
XML Settings  
The EDS-MD4/8/16 allows for the configuration of units using an XML configuration record (XCR).  
Export a current configuration for use on other EDS-MD4/8/16 or import a saved configuration file.  
XML: Export Configuration  
You can export the current system configuration in XML format. The generated XML file can be  
imported later to restore a configuration. It can also be modified and imported to update the  
configuration on this EDS-MD4/8/16 unit or another. The XML data can be dumped to the screen  
or exported to a file on the file system.  
By default, all groups are exported. You may also select a subset of groups to export.  
Table 12-5 XML Exporting Configuration  
XML Export Configuration Description  
Settings  
Export to browser  
Select this option to export the XCR data in the selected fields to the  
browser. Use the “xcr dump” command to export the data to the browser.  
Export to local file  
Select this option to export the XCR data to a file on the device. If you select  
this option, enter a file name for the XML configuration record. Use the “xcr  
export” command to export the data to a local file.  
Export secrets  
Select to export secret password and key information. Use only with a  
secure link, and save only in secure locations.  
Note: Only use with extreme caution.  
Comments  
Select this option to include descriptive comments in the XML.  
Lines to Export  
Select instances to be exported in the line, serial, tunnel and terminal  
groups.  
EDS-MD User Guide  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
12: Advanced Settings  
XML Export Configuration Description  
Settings (continued)  
Groups to Export  
Check the configuration groups that are to be exported to the XML  
configuration record. The group list should be comma delimited and  
encased in double quotes. The list of available groups can be viewed with  
the “xcr list” command.  
To Export Configuration in XML Format  
Using Web Manager  
To export configuration format, click XML in the menu and select Export Configuration.  
Using the CLI  
To enter the XML command level: enable -> xml  
Using XML  
Not applicable.  
XML: Export Status  
You can export the current status in XML format. By default, all groups are exported. You may also  
select a subset of groups to export.  
Table 12-6 Exporting Status  
XML Export Status  
Settings  
Description  
Export to browser  
Select this option to export the XCR data in the selected fields to the  
browser. Use the “xcr dump” command to export the data to the browser.  
Export to local file  
Select this option to export the XCR data to a file on the device. If you select  
this option, enter a file name for the XML configuration record. Use the “xcr  
export” command to export the data to a local file.  
Lines to Export  
Select instances to be exported in the line, serial, tunnel and terminal  
groups.  
Groups to Export  
Check the configuration groups that are to be exported to the XML  
configuration record. The group list should be comma delimited and  
encased in double quotes. The list of available groups can be viewed with  
the “xcr list” command.  
To Export in XML Format  
Using Web Manager  
To export configuration format, click XML in the menu and select Export Status.  
Using the CLI  
To enter the XML command level: enable -> xml  
EDS-MD User Guide  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
12: Advanced Settings  
Using XML  
Not applicable.  
XML: Import Configuration  
Here you can import a system configuration from an XML file.  
The XML data can be imported from a file on the file system or pasted into a CLI session. The  
groups to import can be specified at the command line, the default is all groups.  
Import Configuration from External File  
This import option requires entering the path and file name of the external XCR file you want to  
import.  
Import Configuration from the Filesystem  
This import option picks up settings from a file and your import selections of groups, lines, and  
instances. The list of files can be viewed from the filesystem level of the CLI.  
Table 12-7 Import Configuration from Filesystem Settings  
Import Configuration from  
Filesystem Settings  
Description  
Filename  
Enter the name of the file on the EDS-MD (local to its filesystem) that  
contains XCR data.  
Lines to Import  
Select filter instances to be imported in the line, serial, tunnel and terminal  
groups. This affects both Whole Groups to Import and Text List  
selections.  
Whole Groups to Import  
Text List  
Select the configuration groups to import from the XML configuration  
record. This option imports all instances of each selected group.  
Enter the string to import specific instances of a group. The textual format  
of this string is: <g>:<i>;<g>:<i>;...  
Each group name <g> is followed by a colon and the instance value <i>  
and each <g>:<i> value is separated by a semi-colon. If a group has no  
instance then only the group name <g> should be specified.  
To Import Configuration in XML Format  
Using Web Manager  
To import configuration, click XML in the menu and select Import Configuration.  
Using the CLI  
To enter the XML command level: enable -> xml  
Using XML  
Not applicable.  
EDS-MD User Guide  
80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
13: Updating Firmware  
Obtaining Firmware  
Obtain the most up-to-date firmware and release notes for the unit from the Lantronix Web site  
Loading New Firmware  
Firmware may be updated by sending the file to the EDS-MD4/8/16 over an FTP connection. The  
destination file name on the EDS-MD4, EDS-MD8 or EDS-MD16 must be "firmware.rom". The  
device will reboot upon successful completion of the firmware upgrade.  
Example FTP session:  
$ ftp 192.168.10.127  
Connected to 192.168.10.127.  
220 (vsFTPd 2.0.7)  
Name (192.168.10.127:user): admin  
331 Please specify the password.  
Password:  
230 Login successful.  
Remote system type is UNIX.  
Using binary mode to transfer files.  
ftp> put edsmd_7_2_0_0R8.rom firmware.rom  
200 PORT command successful. Consider using PASV.  
150 Ok to send data.  
226 File receive OK.  
9308164 bytes sent in 3.05 seconds (3047859 bytes/s)  
ftp> quit  
221 Goodbye.  
EDS-MD User Guide  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
14: VIP Settings  
Virtual IP (VIP) Configuration  
Configuring Connect Mode tunnels to use VIP is a simple matter of configuring a tunnel as is  
normally done, but also enabling VIP in the Tunnel Host settings, and using a VIP Name for the  
address.  
VIP Accept Mode tunnels do not require special configuration. If VIP access is enabled (in VIP  
configuration), then VIP Accept Mode requests from a ManageLinx device will be accepted.  
Table 14-1 VIP Configuration  
VIP Settings  
State  
Description  
Select Enabled or Disabled to determine whether to allow Virtual IP addresses to  
be used in Tunnel Connect Mode and to accept incoming Virtual IP connection  
requests to any local listening port.  
To Configure VIP Settings  
Using Web Manager  
To configure VIP settings, click VIP on the menu and select Configuration.  
Using the CLI  
To enter the VIP command level: enable -> config -> vip  
Using XML  
Include in your file: <configgroup name=”vip”>  
Virtual IP (VIP) Status  
The VIP Status shows the current state of the conduit. When configured correctly, a conduit with  
the AccessMyDevice Gateway will be maintained at all times.  
To View VIP Status  
Using Web Manager  
Click VIP on the menu and select Status.  
Using the CLI  
To enter the VIP command level: enable -> config -> vip, show status  
EDS-MD User Guide  
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
14: VIP Settings  
Using XML  
Include in your file: <statusgroup name=”vip”>  
Virtual IP (VIP) Counters  
Table 14-2 VIP Counters  
Description  
VIP Counters  
Data Bytes  
Total bytes in the TCP packets (not the UDP packets)  
The number of packets queued for transmission.  
The number of packets transmitted.  
UDP Packet Queue  
UDP Packets  
Note: UDP counts are packet based, and do not record the number of  
data bytes.  
To View VIP Counters  
Using Web Manager  
Click VIP on the menu and select Counters.  
Using the CLI  
To enter the VIP command level: enable -> config -> vip, show counters  
Using XML  
Include in your file: <statusgroup name=”vip”>  
EDS-MD User Guide  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
15: Branding the EDS-MD4/8/16  
This chapter describes how to brand your EDS-MD4, EDS-MD8 or EDS-MD16 by using Web  
Manager and Command Line Interface (CLI). It contains the following sections on customization:  
Web Manager Customization  
Customize the Web Manager's appearance by modifying index.html, style.css, and the product  
logo. The style (fonts, colors, and spacing) of the Web Manager is controlled with style.css. The  
text and graphics are controlled with index.html. The product logo is the image in top-left corner of  
the page and defaults to a product name image.  
Note: The recommended dimensions of the new graphic are 300px width and 50px  
height.  
The Web Manager files are hidden and are incorporated directly into the firmware image but may  
be overridden by placing the appropriate file in the appropriate directory on the EDS-MD4, EDS-  
MD8 or EDS-MD16 file system.  
Web Manager files can be retrieved and overridden with the following procedure:  
1. FTP to the EDS-MD4/8/16 device.  
2. Make a directory (mkdir) and name it http/config.  
3. Change to the directory (cd) that you created in step 2 (http/config).  
4. Save the contents of index.html and style.css by using a web browser and navigating to  
5. Modify the file as required or create a new one with the same name.  
6. To customize the product logo, save the image of your choice as logo.gif.  
7. Put the file(s) by using put <filename>.  
8. Type quit. The overriding files appear in the file system's http/config directory.  
9. Restart any open browser to view the changes.  
10. If you wish to go back to the default files in the firmware image, simply delete the overriding  
files from the file system.  
EDS-MD User Guide  
84  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
15: Branding the EDS-MD4/8/16  
Short and Long Name Customization  
You can customize the short and long names in your EDS-MD4/8/16. The names display in the  
CLI show command and in the System web page in the Current Configuration table. The short  
name is used for the show command. Both names display in the CLI Product Type field.  
Table 15-1 Short and Long Name Settings  
Name Settings  
Short Name  
Description  
Enter a short name for the system name. A maximum of 32 characters are  
allowed.  
Long Name  
Enter a long name for the system name. A maximum of 64 characters are  
allowed.  
To Customize Short or Long Names  
Using Web Manager  
To access the area with options to customize the short name and the long name of the  
product, or to view the current configuration, click System in the menu.  
Using the CLI  
To enter the command level: enable  
Using XML  
Include in your file:  
<configitem name=“short name”>  
and  
<configitem name=“long name”>  
EDS-MD User Guide  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Appendix A: Technical Support  
If you are unable to resolve an issue using the information in this documentation, please contact  
Technical Support:  
Technical Support US  
Check our online knowledge base or send a question to Technical Support at  
Technical Support Europe, Middle East, Africa  
Phone: +33 13 930 4172  
Firmware downloads, FAQs, and the most up-to-date documentation are available at  
When you report a problem, please provide the following information:  
Your name, and your company name, address, and phone number  
Lantronix model number  
Lantronix serial number/MAC address  
Firmware version (on the first screen shown when you Telnet to the device and type show)  
Description of the problem  
Status of the unit when the problem occurred (please try to include information on user and  
network activity at the time of the problem)  
Additionally, it may be useful to export and submit the exported XML Configuration file.  
EDS-MD User Guide  
86  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Appendix B: Binary to Hexadecimal Conversions  
Many of the unit's configuration procedures require you to assemble a series of options  
(represented as bits) into a complete command (represented as a byte).  
The resulting binary value must be converted to a hexadecimal representation.  
Use this chapter to learn to convert binary values to hexadecimals or to look up hexadecimal  
values in the tables of configuration options. The tables include:  
Command Mode (serial string sign-on message)  
AES Keys  
Converting Binary to Hexadecimal  
Table 17-1 Binary to Hexadecimal  
Conversion  
Following are two simple ways to convert binary  
numbers to hexadecimal notation.  
Decimal  
Binary  
0000  
0001  
0010  
0011  
0100  
0101  
0110  
0111  
1000  
1001  
1010  
1011  
1100  
1101  
1110  
1111  
Hex  
0
0
Conversion Table  
Hexadecimal digits have values ranging from 0 to F,  
which are represented as 0-9, A (for 10), B (for 11),  
etc. To convert a binary value (for example, 0100  
1100) to a hexadecimal representation, treat the  
upper and lower four bits separately to produce a two-  
digit hexadecimal number (in this case, 4C). Use the  
following table to convert values from binary to  
hexadecimal.  
1
1
2
2
3
3
4
4
5
5
6
6
Scientific Calculator  
Another simple way to convert binary to hexadecimal  
is to use a scientific calculator, such as the one  
available on the Windows operating systems. For  
example:  
7
7
8
8
9
9
1. On the Windows Start menu, click Programs ->  
10  
11  
12  
13  
14  
15  
A
B
C
D
E
F
Accessories -> Calculator.  
2. On the View menu, select Scientific. The  
scientific calculator appears.  
3. Click Bin (Binary), and type the number you want  
to convert.  
EDS-MD User Guide  
87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Figure 17-2 Windows Scientific Calculator  
4. Click Hex. The hexadecimal value appears.  
Figure 17-3 Hexadecimal Values in the Scientific Calculator  
EDS-MD User Guide  
88  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Appendix C: Compliance  
(According to ISO/IEC Guide 22 and EN 45014)  
Manufacturer's Name & Address:  
Lantronix  
167 Technology Drive, Irvine, CA 92618 USA  
Product Name Model:  
EDS-MD4, EDS-MD8 and EDS-MD16 Port Device Servers  
Conform to the following standards or other normative documents:  
Table 18-1 Applicable Medical Standards  
Emissions  
Immunity  
EN 60601-1-2: 2007  
EN 60601-1-2: 2007  
CISPR 11:2003+A1:2004+A2:2006  
EN 61000-3-2: 2006 + A1: 2009 + A2: 2009  
EN 61000-3-3: 2008  
EN 61000-4-2: 2009  
EN 61000-4-3: 2006 + A1: 2008  
EN 61000-4-4: 2004 + A1: 2010  
EN 61000-4-5: 2006  
EN 61000-4-6: 2009  
EN 61000-4-8: 1994 + A1: 2001  
EN 61000-4-11: 2004  
Table 18-2 Applicable ITE Standards  
Emissions  
Immunity  
FCC Part 15 Subpart B  
EN 55024: 1998 +A1: 2001 +A2: 2003  
EN 61000-4-2: 2009  
Industry Canada ICES-003 Issue 4 February 2004  
CISPR 22: 2005 + A1: 2005 + A2: 2006 Information EN 61000-4-3: 2006 + A1: 2008  
Technology Equipment  
EN 61000-4-4: 2004 + A1: 2010  
VCCI V-3/2010.04  
EN 61000-4-5: 2006  
AS/NZS CISPR 22: 2009  
EN 61000-4-6: 2009  
EN 55022: 2006 + A1:2007  
EN 61000-4-8: 1994 + A1: 2001  
EN 61000-3-2: 2006 + A1: 2009 + A2: 2009  
EN 61000-4-11: 2004  
EN 61000-3-3: 2008  
Note: In the event of an ESD surge to the unit, a full power cycle may need on the unit  
for it to regain its full functionality.  
EDS-MD User Guide  
89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Table 18-3 Regulatory Compliance  
Standard  
Description  
United States:  
UL 60950-1: 2nd edition  
Standard for Safety for Information Technology Equipment – Safety – Part 1:  
General Requirements  
United States:  
UL 60601-1: 1st edition  
Standard for Safety for Medical Electrical Equipment, Part 1: General  
Requirements for Safety  
Canada:  
Standard for Safety for Information Technology Equipment – Safety – Part 1:  
General Requirements  
CAN/CSA-C22.2  
No. 60950-1-07  
2nd edition  
Canada:  
Medical Electrical Equipment, Part 1: General Requirements for Safety  
CAN/CSA C22.2  
No. 601.1: 1990  
International:  
IEC 60601-1: 1998 (2nd  
edition)  
Standard for Safety for Medical Electrical Equipment, Part 1: General  
Requirements for Safety  
International:  
Medical Electrical Equipment -- Part 1: General Requirements for Safety  
IEC with Japan Deviations  
JIS T 0601-1:1999  
International:  
Japan  
VCCI Japan  
VCCI V-3/2008.04  
International:  
C-Tick Australia/New Zealand  
Australia  
AS/NZS CISPR 22: 2006  
Manufacturer's Contact:  
Lantronix  
167 Technology Drive, Irvine, CA 92618 USA  
Tel: 949-453-3990  
Fax: 949-450-7249  
EDS-MD User Guide  
90  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Figure 18-4 Suppliers Declaration of Conformity  
EDS-MD User Guide  
91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
RoHS Notice  
All Lantronix products in the following families are China RoHS-compliant and free of the following hazardous  
substances and elements:  
Lead (Pb)  
Mercury (Hg)  
Polybrominated biphenyls (PBB)  
Cadmium (Cd)  
Product Family Name  
Hexavalent Chromium (Cr (VI))  
Toxic or hazardous Substances and Elements  
Polybrominated diphenyl ethers (PBDE)  
Lead  
(Pb)  
Mercury  
(Hg)  
Cadmium  
(Cd)  
Hexavalent  
Chromium (Cr biphenyls (PBB)  
(VI))  
Polybrominated  
Polybrominated diphenyl  
ethers (PBDE)  
UDS1100 and 2100  
EDS  
MSS100  
IntelliBox  
XPress DR & XPress-DR+  
SecureBox 1101 & 2101  
WiBox  
UBox  
MatchPort  
SLC  
XPort  
WiPort  
SLB  
SLP  
SCS  
SLS  
DSC  
PremierWave  
Micro125  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
O: toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit  
requirement in SJ/T11363-2006.  
X: toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the  
limit requirement in SJ/T11363-2006.  
EDS-MD User Guide  
92  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix D: Lantronix Cables, Adapters and Serial  
Port Pinouts  
Lantronix cables and adapters for use with EDS-MD4, EDS-MD8 and EDS-MD16 are listed here  
according to part number and application.  
Cables and Adapters  
Table 19-1 Lantronix Cables and Adapters  
Lantronix P/N  
500-153  
Description  
Applications  
RJ45-to DB9F  
Connects the RJ45 RS232 serial ports of EDS-MD to a DB9M DTE  
interface of a PC or serial device to check that serial ports in the EDS-  
MD are functioning properly.  
200.2066A  
200.2067A  
200.2069A  
200.2070A  
200.2071  
Adapter RJ45-to-  
DB25M  
Allows a standard straight-pinned CAT5 cable to connect the EDS-MD  
RJ45 serial ports to the DB25F DTE interface of a serial device.  
Adapter RJ45-to-  
DB25F  
Allows a standard straight-pinned CAT5 cable to connect the EDS-MD  
RJ45 serial ports to the DB25M DTE interface of a serial device.  
Adapter RJ45-to-  
DB9M  
Allows a standard straight-pinned CAT5 cable to connect the EDS-MD  
RJ45 serial ports to the DB9F DTE interface of a serial device.  
Adapter RJ45-to-  
DB9F  
Allows a standard straight-pinned CAT5 cable to connect the EDS-MD  
to the DB9M DTE interface of a PC or serial device.  
Adapter RJ45-to-  
DB9M  
Allows a standard straight-pinned CAT5 cable to connect the EDS-MD  
RJ45 serial ports to the DB9F DCE interface of a serial device.  
200.2072  
Adapter RJ45-to-  
DB9F  
Allows a standard straight-pinned CAT5 cable to connect the EDS-MD  
to the DB9M DCE interface of a PC or serial device.  
200.2073  
Adapter RJ45-to-  
DB25M  
Allows a standard straight-pinned CAT5 cable to connect the EDS-MD  
RJ45 serial ports to the DB25F DCE interface of a serial device.  
200.2074  
Adapter RJ45-to-  
DB25F  
Allows a standard straight-pinned CAT5 cable to connect the EDS-MD  
RJ45 serial ports to the DB25M DCE interface of a serial device.  
930-073-R  
930-074-R  
930-075-R  
930-076-R  
Power Cord,  
Hospital Grade US  
Conducts power to the EDS-MD, for the United States.  
Power Cord,  
Europe  
Conducts power to the EDS-MD, for Europe.  
Power Cord, United  
Kingdom  
Conducts power to the EDS-MD, for the United Kingdom.  
Conducts power to the EDS-MD, for Australia.  
Conducts power to the EDS-MD, for Israel.  
Power Cord,  
Australian  
930-077-R  
Power Cord, Israel  
ADP010104-01  
Adapter "Rolled"  
RJ45-to-RJ45  
Allows a standard straight-pinned CAT5 cable to connect the EDS-MD  
to an RJ45 console port on products from Cisco and other  
manufacturers.  
EDS-MD User Guide  
93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Adapters and Serial Port Pinouts  
Figure 19-2 RJ45 Receptacle to DB25M DTE Adapter (PN 200.2066A)  
Figure 19-3 RJ45 Receptacle to DB25M DCE Adapter (PN 200.2073)  
EDS-MD User Guide  
94  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Figure 19-4 RJ45 Receptacle to DB25F DTE Adapter (PN 200.2067A )  
Figure 19-5 RJ45 Receptacle to DB25F DCE Adapter (PN 200.2074)  
EDS-MD User Guide  
95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Figure 19-6 RJ45 Receptacle to DB9M DTE Adapter (PN 200.2069A)  
Figure 19-7 RJ45 Receptacle to DB9M DCE Adapter (PN 200.2071)  
EDS-MD User Guide  
96  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Figure 19-8 RJ45 Receptacle to DB9F DTE Adapter (PN 200.2070A)  
Figure 19-9 RJ45 Receptacle to DB9F DCE Adapter (PN 200.2072)  
EDS-MD User Guide  
97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Figure 19-10 RJ45 to RJ45 Adapter (ADP010104-01)  
Note: The cable ends of the ADP010104-01 are an RJ45 socket on one end and a RJ45  
plug on the other instead of RJ45 sockets on both ends.  
EDS-MD User Guide  
98  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

Kyocera Cell Phone KYOCERA S2100 User Manual
Lathem Time Clock AT DDC4 User Manual
Lenoxx Electronics Air Conditioner 15CHAX User Manual
Life Fitness Home Gym SUB User Manual
Linear Satellite Radio 3060 User Manual
Martin Audio Portable Speaker HTKW1 User Manual
Marvel Industries Beverage Dispenser 6OSWCE User Manual
McIntosh DVD Player MVP861 User Manual
Metra Electronics Automobile Accessories GMLAN11 100 User Manual
MGE UPS Systems Power Supply 2200 RT 2U User Manual