Wiring Harness Update Kit
Assembly Instructions
Razor Series ZR44 & ZR52
Manual No. 356-141M
Before You Start
Instructions For Kit No 356-142A
A detailed listing of parts for wiring harness update kit
No. 356-142A is provided on page 4. Use this list as a
checklist to inventory parts received.
When you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
!
1. Park mower on a flat surface and move control levers
to park.
These instructions contain only information required to
assemble the Wiring Harness Kit to the Razor Series
ZR44 & ZR52 Riding Mowers. A detailed Operator’s
Manual was supplied with the Razor. Refer to the
Operator’s Manual for additional specific information
especially information relating to safety concerns. Also
included in the Operator’s Manual is important
information on operation, adjustment, troubleshooting,
and maintenance for this attachment (some manual
sections do not apply to all options).
2. Turn off engine and remove ignition key.
3. Raise seat deck fully up.
Refer to Figure 1:
4. Disconnect negative ground wire (black wire) from
the battery’s negative post ( - ). Place ground wire in
a location where it cannot touch the battery posts.
A separate Parts Manual for replacement parts can be
purchased from your dealer or available free of charge at
handy when placing an order.
Negative
Ground
Negative Post (-)
Manual Part Numbers:
• Operator’s Manual . . . . . . . . . . . . . . . . . .356-059M
• Parts Manual . . . . . . . . . . . . . . . . . . . . . . . 356-059P
General Information
23811
Remove Ground Battery Connection
Figure 1
Some ZR44 & ZR52 Razors may be experiencing a small
drain on the battery when units are parked and the
ignition off. Over time this small electrical drain can
deplete the battery to a point that it fails to start the
mower. If a unit is experiencing a repeated battery
discharge for no obvious reason, installation of this
simple kit will eliminate that condition.
Refer to Figure 2:
5. Check battery drain with an amp meter by placing
black probe on the negative battery post and red
probe on the ground wire as shown. A drain of 7
milliamps or more is an indication that it would be
helpful to install this wiring harness kit.
These assembly instructions apply to the Razor ZR44
and ZR52 Kit Number:
23812
7 milliamps
or greater
356-142A
RAZOR HARNESS UPDATE KIT
Tools required:
• Electrical Tape
• Wire Cutters
Red Probe
• Wire Stripper
• Electrical Wire Crimpers
• Two 10 mm Metric Wrenches
Black Probe
• Terminal Removal Tool or
a Small Thin Bladed Screw Driver
Negative Post (-)
Ground wire
Battery Drain Check
Figure 2
© Copyright 2005 Printed
1/16/07
■
Manual No. 356-141M
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Instructions For Kit No 356-142A
Refer to Figure 8:
14. Crimp Butt Connector with crimping part of wire
strippers to secure connector place.
Butt
Connector
Main Wiring
Harness
Orange
Wire
Crimp Portion of
the Wire Strippers
Butt
Connector
Splice
Connector
Main Wire
harness
24594
Crimping Butt connector
Figure 8
Bare Wire
End of New
Splice Wire
Refer to Figure 9:
15. Plug the new splice wire spade terminals into the
terminal slots where the purple ground wires were
removed.
Metal
Prong
Splice
Connector
cover
23818
New Splice Wire
Figure Description
Figure 10
Refer to Figure 11:
21. Reattach main wiring harness to mower frame with
new plastic ties.
22. Check battery drain as outlined in step 5 before
reconnecting battery ground wire. Amp reading
should not exceed .001 milliamps.
Terminal Ends
23. Reconnect battery ground wire to negative post (-).
Bare Wire End
23817
Plug Splice Wire Into Connector
Figure 9
Negative
Ground Wire
Refer to Figure 10:
16. Insert bare wire end of new splice wire into splice
connector as shown.
Negative Post ( - )
17. Locate orange wire leading into main wiring harness
and attach splice connector over orange wire as
shown.
IMPORTANT: Force metal prong down with pliers
before closing splice connector cover. Forcing prong
down with cover will damage the splice connector.
21127
18. Make certain bare wire end is fully inserted into the
splice connector and then force metal prong down
into the connector with pliers.
Figure Description
Figure 11
24. Lower seat deck and start mower to verify it will start.
Shut mower off and lock seat down to complete
installation.
19. Close splice connector cover. Make certain it snaps
shut.
20. (Optional) Press Butt Connector against main wire
harness and secure in place with electrical tape.
1/16/07
■
Manual No. 356-141M
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Razor Harness Update Kit Part No. 356-142A
Qty.
Part No.
Part Description
1
2
1
1
1
356-141M
800-112C
833-401C
833-381C
833-460C
INSTRUCTION,HONDA ELEC UPDATE
CABLE TIE .19X7.25 1.75D 50LB
HARNESS UPDATE WIRE Kit
BUTT CONNECTOR (Included with 833-401C Kit)
CONNECTOR SPLICE 16-14AWG (Included with 833-401C Kit)
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|