Flail Mowers
FM2060 & FM2072
17962
309-100M
Operator’s Manual
Read the Operator’s manual entirely. When
you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
!
© Copyright 2008 Printed
3/25/08
Cover photo may show optional equipment
not supplied with standard unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Important Safety Information
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Safety at All Times
Look For The Safety Alert Symbol
Thoroughly read and understand
the instructions given in this
manual before operation. Refer to
the “Safety Label” section, read
all instructions noted on them.
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control and accident prevention
are dependent upon the awareness, concern,
prudence and proper training of personnel involved in
the operation, transport, maintenance and storage of
equipment.
Do not allow anyone to operate
this equipment who has not fully
read and comprehended this
manual and who has not been
properly trained in the safe
operation of the equipment.
!
▲ Operator should be familiar with
!
Be Aware of
Signal Words
WARNING
all functions of the unit.
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may also
be used to alert against unsafe
practices.
▲ Operate implement from the
driver’s seat only.
A Signal word designates a degree or
level of hazard seriousness. The
signal words are:
▲ Make sure all guards and shields
are in place and secured before
operating implement.
!
DANGER
▲ Do not leave tractor or implement
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.
unattended with engine running.
!
CAUTION
▲ Dismounting from a moving
tractor could cause serious injury
or death.
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
▲ Do not stand between the tractor
and implement during hitching.
▲ Keep hands, feet, and clothing
away from power-driven parts.
▲ Wear snug fitting clothing to avoid
entanglement with moving parts.
▲ Watch out for wires, trees, etc.,
when raising implement. Make
sure all persons are clear of
working area.
▲ Turning tractor too tight may
cause implement to ride up on
wheels. This could result in injury
or equipment damage.
For Your Protection
Shutdown and Storage
▲ Thoroughly read and understand
the “Safety Label” section, read all
instructions noted on them.
▲ Lower machine to ground, put
tractor in park, turn off engine, and
remove the key.
▲ Detach and store implements in a
area where children normally do
not play. Secure implement by
using blocks and supports.
OFF
FM2060 & FM2072 Flail Mowers 309-100M
3/25/08
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
▲ Use the following maximum
speed - tow load weight ratios as
a guideline:
Use Safety
Lights and Devices
Transport
Machinery Safely
20 mph when weight is less
than or equal to the weight of
tractor.
10 mph when weight is double
the weight of tractor.
▲ Slow moving tractors, self-
propelled equipment, and towed
implements can create a hazard
when driven on public roads. They
are difficult to see, especially at
night.
▲ Flashing warning lights and turn
signals are recommended
whenever driving on public roads.
Use lights and devices provided
with implement.
▲ Comply with state and local laws.
▲ Maximum transport speed for
implement is 20 mph. DO NOT
EXCEED. Never travel at a speed
which does not allow adequate
control of steering and stopping.
Some rough terrain require a
slower speed.
▲ Sudden braking can cause a
towed load to swerve and upset.
Reduce speed if towed load is not
equipped with brakes.
▲ IMPORTANT: Do not tow a load
that is more than double the
weight of tractor.
Practice Safe Maintenance
▲ Do not grease or oil implement
▲ Understand procedure before
doing work. Use proper tools and
equipment, refer to Operator’s
Manual for additional information.
while it is in operation.
▲ Inspect all parts. Make sure parts
are in good condition & installed
properly.
▲ Work in a clean dry area.
▲ Remove buildup of grease, oil or
▲ Lower the implement to the
ground, put tractor in park, turn off
engine, and remove key before
preforming maintenance.
debris.
▲ Remove all tools and unused
parts from implement before
operation.
▲ Allow implement to cool
completely.
FM2060 & FM2072 Flail Mowers 309-100M
Download from Www.Somanuals.com. All Manuals Search And Download.
3/25/08
2
Land Pride
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Wear
Prepare for Emergencies
Protective Equipment
▲ Be prepared if a fire starts.
▲ Protective clothing and equipment
▲ Keep a first aid kit and fire
should be worn.
extinguisher handy.
▲ Wear clothing and equipment
appropriate for the job. Avoid
loose fitting clothing.
▲ Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
▲ Keep emergency numbers for
doctor, ambulance, hospital and
fire department near phone.
▲ Operating equipment safely
requires the full attention of the
operator. Avoid wearing radio
headphones while operating
machinery.
911
Keep Riders
Off Machinery
▲ Riders obstruct the operator’s
view, they could be struck by
foreign objects or thrown from the
machine.
▲ Never allow children to operate
equipment.
FM2060 & FM2072 Flail Mowers 309-100M
Download from Www.Somanuals.com. All Manuals Search And Download.
3/25/08
3
Land Pride
Important Safety Information
4. Refer to this section for proper label placement.
Safety Labels
Your mower comes equipped with all safety labels in
place. They were designed to help you safely operate
your implement. Read and follow their directions.
To install new labels:
a. Clean the area the label is to be placed.
b. Spray soapy water on the surface where the label is to
be placed.
1. Keep all safety labels clean and legible.
2. Replace all damaged or missing labels. To order new
labels go to your nearest Land Pride dealer.
3. Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as
specified by Land Pride. When ordering new components
make sure the correct safety labels are included in the
request.
c. Peel backing from label. Press firmly onto the surface.
a. Squeeze out air bubbles with the edge of a credit card.
818-130C
Caution: To avoid injury
17962
818-230C
Red Reflector (Both Sides)
17964
818-540C
Danger: Guard Missing
13314
FM2060 & FM2072 Flail Mowers 309-100M
3/25/08
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Important Safety Information
Beneath Guard
818-543C
Danger: Guard Missing
17962
ROTATING DRIVELINE
KEEP AWAY!
818-552C
Danger: Rotating Driveline
179625
818-552C
Danger: Rotating Driveline
ROTATING DRIVELINE
KEEP AWAY!
13314
FM2060 & FM2072 Flail Mowers 309-100M
Download from Www.Somanuals.com. All Manuals Search And Download.
3/25/08
5
Land Pride
Important Safety Information
818-558C
Warning: General
179624
818-556C
Danger: Thrown Object
179624
179624
838-079C
Danger: Rotating
Knives Both sides
FM2060 & FM2072 Flail Mowers 309-100M
3/25/08
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Introduction
LInantdrPoriddeuweclctoimoens you to the growing family of new
Definitions
product owners.
NOTE: A special point of information that the
operator must be aware of before continuing.
This Flail Mower has been designed with care and built
by skilled workers using quality materials. Proper
assembly, maintenance and safe operating practices will
help you get years of satisfactory use from the machine.
IMPORTANT: A special point of information related
to its preceding topic. Land Pride’s intention is that
this information should be read and noted before
continuing.
Application
The medium duty FM2060 and FM2072 Series Flail
Mowers are designed and built by to provide excellent
cutting performance on gently sloping or slightly
contoured grassy right-of ways, roadsides, ditches,
pastures, nurseries, and smaller fields of light row crop
debris, stalks, and residual agricultural trash. The 60"
and 72" cutting widths and 3/4" to 4" cutting height and
ability to cut weeds and brush up to 1" in diameter makes
these flail mowers well suited for nursery and agricultural
applications where grass, brush, pruning’s, small
saplings, and cotton residue are present. Either model
equipped with fine cut knives will perform extremely well
cutting material up to 1" in diameter or provide a very
respectable quality of cut for grooming yards, municipal
parks, medians, or right of ways.
Owner Assistance
The Warranty Registration card should be filled out by
the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
If customer service or repair parts are required contact a
Land Pride dealer. A dealer has trained personnel, repair
parts and equipment needed to service the mower.
The parts on your mower have been specially designed
and should only be replaced with genuine Land Pride
parts. Therefore, should your mower require
replacement parts go to your Land Pride Dealer.
Serial Number Plate
Both models offer a Cat. 1 three-point hitch for tractors
not to exceed 55 PTO horsepower. The three point
hitches on both models offer centered mounting or offset
capability 6" to the right making them even more
desirable for cutting in and around trees with extremely
low hanging branches. Both models also offer a Cat. 4
and 540rpm shielded driveline. The FM2060 and
FM2072 Flail Mowers, with their horizontal cutting rotor
design, also provide for greatly reduced potential of
launching projectiles out from under the mower making
them an excellent choice for state and municipal mowing
applications.
For prompt service always use the serial number and
model number when ordering parts from your Land Pride
dealer. Be sure to include your serial and model numbers
of your serial number plate.
17962
information and performance enhancing options.
Serial Number Plate Location
Figure 1
Further Assistance
Using This Manual
• This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
Your dealer wants you to be satisfied with your new
mower. If for any reaso7n you do not understand any part
of this manual or are not satisfied with the service
received, the following actions are suggested:
1. Discuss the matter with your dealership service
manager making sure he is aware of your problems
and that he has had the opportunity to assist you.
• The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
• To order a new Operator’s or Parts Manual contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge from our website at
Service & Support Center by your dealer.
3. For further assistance write to:
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Terminology
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Salina, Ks. 67402-5060
E-mail address
FM2060 & FM2072 Flail Mowers 309-100M
3/25/08
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Assembly and Set-up
Section 1: Assembly and Set-up
Tractor Requirements
Hitch Assembly
This mower is designed with a 3-Point category I hitch.
Horse power rating of tractor should not exceed 40 PTO
horse power for the Flail Mowers.
Refer to Figure 1-1:
4. The hitch is disassembled for ease in shipping.
5. Assemble the hitch (#1) to the flail mower and secure
with the bolts (#2), lock washers (#3) and nuts (#4)
as shown.
NOTE: In order to maintain steering control, ballast
may need to be added to your tractor. To determine
whether or not to add the ballast, refer to your
tractor’s operator manual.
6. The hitch can be assembled in two different
positions; (#5) and (#6) for either a left offset or right
offset.
7. Tighten all hardware.
Hitch Assembly
Figure 1-1
17966
FM2060 & FM2072 Flail Mowers 309-100M
Download from Www.Somanuals.com. All Manuals Search And Download.
3/25/08
8
Land Pride
Section 1: Assembly and Set-up
4. Attach the chain from the driveline shield to one of
Tractor Hook-Up
the upper hitch braces to ensure that the shield does
not rotate.
1. Be certain that tractor draw bar will not interfere.
Move draw bar ahead or remove if required. Draw bar
should also be checked for clearance when unit is
being raised for the first time.
5. Should the driveline require shortening:
d. Hold the half-shafts next to each other in the
shortest working position and mark them.
2. Align lower link arms of tractor to hitch clevises on
mower. Insert lower hitch pins into lower ball swivels
and attach linch pins.
e. Shorten inner and outer guard tubes equally.
f. Shorten inner and outer sliding profiles by the
same length as the guard tubes.
3. Attach tractor top link to upper floating hitch on
mower with pin supplied. Secure with lock pin.
g. Proper overlap is a minimum of one-half the
length of each tube, with both tubes being of equal
length.
4. Adjust the tractor top link in or out to place the upper
hitch pin vertically above or slightly behind the lower
flotation. The mower should be run with the back 15
degrees lower than the front.
h. Round off all sharp edges and remove burrs.
Grease sliding profiles.
Driveline Installation
1. Slide driveline end with extended safety cone over
splined shaft of the gearbox and secure with
attaching device.
!
CAUTION
Tractor PTO shield and all mower guards must be in place at
all times during operation!
2. Slide driveline over the tractor’s splined PTO shaft
and secure with locking device of driveline.
3. Driveline should now be moved back and forth to
insure that it is secure on the PTO shaft of the tractor
and mower gearbox.
17967
Tractor Hook-Up
Figure 1-2
FM2060 & FM2072 Flail Mowers 309-100M
Download from Www.Somanuals.com. All Manuals Search And Download.
3/25/08
9
Section 2: Operating Instructions
Section 2: Operating Instructions
2. Check that all plugs in gearbox have been replaced
and tightened properly.
Transporting
NOTE: Always disengage PTO before raising the
mower to transport position.
3. Be sure all mower knives, bolts and nuts are tight.
4. Be certain all guards and shields are in place and
secure.
6. When raising the mower to the transport position, be
sure that driveline does not contact tractor or mower.
Adjust and set the tractor’s 3-point hitch lift height so
that the driveline does not contact mower deck in the
fully raised position.
5. Grease driveline shaft and all other grease fittings.
6. Clear the area to be mowed of rocks, branches and
other foreign objects.
7. Lower mower to ground. Set tractor throttle at
approximately 1/4 open. Engage PTO to start blades
rotating.
7. Be sure to reduce tractor ground speed when
turning, leaving enough clearance so the mower
does not contact obstacles such as buildings, trees
or fences.
8. Operate with 540 rpm PTO tractor.
9. At first begin mowing at a slow forward speed and
shift up until the desired speed is achieved -
maintaining 540 PTO rpm.
8. Select a safe ground travel speed when transporting
from one area to another. When traveling on
roadways, transport in such a way that faster moving
vehicles may pass safely.
10. Mower knives will cut better at a faster blade speed
than at reduced throttle.
9. When traveling over rough or hilly terrain, shift tractor
to a lower gear.
11. After mowing the first 50 feet, stop and check to see
that the mower is adjusted properly.
12. Do not make sharp turns or attempt to back up while
!
CAUTION
mower is on the ground.
When traveling on public roads, whether at night or during the
day, use accessory lights and devices for adequate warning to
operators of other vehicles. Comply with all Federal, State,
and local laws.
13. Do not engage PTO with mower in the fully raised
position. Do not engage PTO at full throttle.
Operating Instructions
Now that you have familiarized yourself with the
Operator’s Manual, completed the Operators Checklist,
properly attached your flail mower to your tractor, made
the right offset or center adjustments, and preset your
cutting height, you’re almost ready to begin using your
Land Pride FM2060 or FM2072 Flail Mower.
Mowing Instructions
1. Clear the area to be mowed of objects and debris
that might be picked up and thrown by the mower
blades.
2. Grass is best cut when it is dry. Mowing wet grass
can cause plugging resulting in grass clumps behind
the mower.
It’s now time to do a running operational safety check. If
at any time during this safety check you detect a
malfunction in either the mower or tractor shut the tractor
off immediately, remove the key, and make necessary
repairs or adjustments before continuing on.
3. Grass should be mowed frequently as shorter
clippings deteriorate faster.
4. If mowing extremely tall grass, it is best to raise
cutting height and mow the area, then lower cutting
height and mow a second time at the desired height.
Make sure the tractor’s park brake is engaged, the
tractor’s PTO is disengaged, and the mower is resting on
the ground. Start the tractor and then back the tractor
throttle off till the engine is at low idle. With the tractor’s
rear hydraulic lift control lever, raise the mower to
transport position making sure that the PTO shaft is not
in a bind and does not come in contact with the mower
frame. Lower the unit to cutting position and, with the
tractor still at low idle, engage the PTO. If everything is
running smoothly at this point increase the engine rpm
until the tractors engine reaches full PTO operating
speed which will be 540 rpm. Slowly raise the cutter to
transport height to make sure the driveline does not bind
or chatter. Then return the engine to low idle, disengage
PTO, and position the adjustable stops on the tractor’s
hydraulic lift lever control console so the cutter can be
consistently returned to the same cutting and transport
height.
!
CAUTION
When mowing in sandy soil areas, wear may occur to the
mower knives from sand erosion. Frequent inspection should
be made and knives replaced if damaged.
Operating Instructions
Proper servicing and adjustments are the key to the long
life of any machine. With careful and systematic
inspection of the mower, costly maintenance, time and
repair can be avoided.
Before beginning to mow, the following inspection should
be performed:
FM2060 & FM2072 Flail Mowers 309-100M
3/25/08
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 2: Operating Instructions
You should now be ready to move to the cutting site to
begin mowing. You should have inspected and should
only be cutting in an area you are familiar with which is
relatively free of debris and unseen objects. Never
assume an area is clear and extremely tall grass or brush
should be cut twice to detect potential hazards. In the
event you do strike an object, stop the tractor and cutter
immediately to inspect the rotor and make any necessary
repairs before resuming operation. It pays to inspect a
new area and to develop a plan before you cut.
Normal mowing speed will be between 2-5 mph and you
will need to maintain tractor PTO speed to produce a
clean cut so make a tractor gear and range selection that
will maintain this combination. Generally the quality of
cut or degree of debris pulverization will be better at
lower ground speeds and cutting denser ground cover or
heavier brush may create the need to slow down. Always
cut downward on slopes and avoid crossing the face of
steep slopes. Avoid sharp drops and cross diagonally
through dips to prevent hanging up the tractor and
mower. Slow down in turns and avoid sharp turns if at all
possible. Remember to look back often. Always be
aware and extremely cautious when there are people,
pets, livestock, and valuable property in your immediate
operating vicinity.
Now you’re prepared and well briefed so lets begin
cutting. Reduce the tractor’s engine rpm, make sure the
mower is on the ground and in cutting position, engage
the PTO, raise the engine rpm to the appropriate PTO
speed, and begin mowing. Operators must plan ahead
and choose a cutting route that allows safe turns. Try
increasing or decreasing ground speed to determine the
effect on quality of cut. With a little practice you will be
pleased with what you and your Land Pride Flail mower
can do.
Dense growth will require more horsepower and will
cause you to slow down especially if you are
encountering material up to 1" in diameter. The fine cut
knives on either unit are much better suited for a finer
quality of cut in grass cutting applications and in no case
should fine cut blades be used for cutting material
greater than 1’ in diameter.
When you are done mowing, need to take a break, or just
need to make a few adjustments to the mower,
remember to always do the following. Reduce the
tractor’s engine rpm, disengage the PTO, stop on level
ground, set the park brake, turn off the engine, and
remove the key. Land Pride flail mowers are very user
friendly and easy to operate. With a little practice you
should be operating your Land Pride Flail Mower like an
expert in no time at all.
FM2060 & FM2072 Flail Mowers 309-100M
Download from Www.Somanuals.com. All Manuals Search And Download.
3/25/08
11
Section 3: Adjustments
Section 3: Adjustments
Leveling the Mower
3-Point Hitch Adjustments
The 3-point hitch system on this mower has been
designed for front to back flotation when mowing on
uneven terrain. Adjust the tractor’s top link to place the
upper hitch pin vertically above or slightly behind the
lower hitch pins. The mower should be run with the back
15 degrees lower than the front.
NOTE: Tractor and mower should be on level
ground.
Leveling can be adjusted with the tractor’s 3-point.
Cutting Height Adjustment
Refer to Figure 3-1:
There is also two different positions for a left or right
The machines cutting height depends upon the position
of the rear roller.
1. Remove the bolts that fix the roller on both sides.
!
CAUTION
2. Lift or lower both sides of the roller in equal
measurements.
Engage parking brake, shut off tractor, remove key and
disengage PTO before making any height adjustments!
3. Replace the bolts and re-tighten.
Belt Tension
!
CAUTION
Belt drive system under spring tension; use care to avoid
bodily harm!
The Belt tension should be checked after the first 20
hours of use. And then every 40 hours of use.
1. To check tension apply approximately 22 pounds of
pressure half way between the pulleys. There should
be approximately 3/8” of deflection.
2. If there is excessive deflection the belts should be
3. Excessive tension on the belt may lead to premature
failure of belt and drive components.
17965
Cutting Height
Figure 3-1
!
WARNING
Excessive tension on the belt may lead to premature failure of
belt and drive components. Excessive tension on the belt may
also lead to a safety hazard to the operator or bystanders.
FM2060 & FM2072 Flail Mowers 309-100M
3/25/08
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 4: Maintenance and Lubrication
Section 4: Maintenance and Lubrication
4. Reinstall idler arm and roller (#3).
Maintenance
5. Reinstall belt guard (#2) and belt guard fender (#1)
Proper servicing and adjustment is the key to the long life
of any farm implement. With careful and systematic
inspection, costly maintenance, time and repair can be
avoided.
.
!
CAUTION
For safety reasons, each maintenance operation must be
performed with tractor PTO disengaged, the mower lowered
completely to the ground and the tractor engine shut off with
ignition key removed.
• After using the mower for several hours, check all bolts
to be sure they are tight and check the tension of the
drive belt. Refer to Belt Tension in the “Adjustments”
section on page 12.
• Lubricate items as listed under Lubrication, this
section, starting on page 14.
• Replace any worn, damaged or illegible safety labels by
obtaining new labels from your Land Pride Dealer.
Information about labels is located under Safety Labels in
the “Important Safety Information” section starting on
Service Mowing Knives
Knife Replacement
IMPORTANT: Make sure that the knife is the same
length as the others on the mower. This will keep the
rotor rotation balanced.
1. Remove bolt and nut.
2. Remove the old knife.
17968
3. Replace the bolt. Tighten to the proper torque as
listed in the Torque Values Chart in the “Appendix”
section on page 19.
Belt Installation
Figure 5-1
Storage
IMPORTANT: Replace knives with Land Pride knives
only.
At the end of the working season or when the mower will
not be used for a long period, it is good practice to clean
off any dirt or grease that may have accumulated on the
mower and any of the moving parts.
V-Belt Installation
Refer to Figure 5-1:
1. Clean as necessary.
2. Check the knives for wear and replace if necessary,
!
CAUTION
see Service Mowing Knives, this section on.
Belt drive system under spring tension; use care to avoid
bodily harm!
3. Inspect the mower for loose, damaged or worn parts
and adjust or replace as needed.
1. Remove the belt guard fender (#1) and belt cover
(#2).
4. Lubricate as noted in the Lubrication portion of this
section starting on page 14.
2. Disengage belt tension by removing the idler arm
and roller (#3).
5. Store unit inside if possible for longer life.
Repaint parts where paint is worn or scratched to prevent
rust. Ask your dealer for aerosol Land Pride Beige touch-
up paint #821-011C.
3. With tension relieved from belt remove old belt from
pulleys.
FM2060 & FM2072 Flail Mowers 309-100M
3/25/08
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 4: Maintenance and Lubrication
Lubrication
Lubrication
Legend
Multi-purpose
spray lube
Multi-purpose
grease lube
Multi-purpose
oil lube
Intervals in hours
at which lubrication
is required
50
25
Hours
Driveline Shaft U-Joints
Type of Lubrication: Multi-purpose Grease
13545
25
Hours
Roller Bearing (Both Ends)
Type of Lubrication: Multi-purpose Grease
17964
25
Hours
Cutter Rotor Bearing (Both Ends)
Type of Lubrication: Multi-purpose Grease
17962
FM2060 & FM2072 Flail Mowers 309-100M
Download from Www.Somanuals.com. All Manuals Search And Download.
3/25/08
14
Land Pride
Section 4: Maintenance and Lubrication
As
Required
DO NOT
OVERFILL!
Gearbox
Type of Lubrication: SAE 90W Gear Lube
Check the oil level in the gearbox by removing the plug at
the side of the box on the right hand side. If oil should flow
from the plug hole there is enough oil. Add oil if necessary
by removing the top plug.
17964
Do not overfill! Should your gearbox require service, take it
to your LAND PRIDE dealer.
NOTE: Mower should be level when checking oil in
gearbox!
Inner
Tube
20
Hours
Driveline Profiles
Type of Lubrication: Multi-purpose Grease
13648
25
Hours
Extension Shaft Bearing
Type of Lubrication: Multi-purpose Grease
17964
FM2060 & FM2072 Flail Mowers 309-100M
3/25/08
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Specifications & Capacities
Section 5: Specifications & Capacities
FM2060 & FM2072 Series Flail Mowers
FM2060
60"
FM2072
72"
Cutting Width
Overall Width
Height
68”
80”
37”
28”
Depth
Weight
616 lbs.
660 lbs.
Cutting Height
Cutting Capacity
Deck Material Thickness
Knives
3/4” - 4”
1”
11 gauge
Fine cut
1980 RPM
4 1/4”
Rotor Shaft Speed
Rotor Diameter
Rotor Rotation
Knife Tip Speed
Number of Knives
Hitch Type
Reverse
8705 fpm
60
72
Category I
6 1/4”
Offset Hitch
PTO Speed
540 RPM
Driveline
Cat 4 w/Over-running Clutch
55 HP
Gearbox Rating
Drive Belts
(2) - “B” Section Belts
5 1/2”
Rear Roller Diameter
FM2060 & FM2072 Flail Mowers 309-100M
Download from Www.Somanuals.com. All Manuals Search And Download.
3/25/08
16
Land Pride
Section 6: Features and Benefits
Section 6: Features and Benefits
FM20 Series
Features
Benefits
Key widths
60”, 72”
6 1/4” Right,
centered offset hitch
The two position hitch for offsetting the mower allows closer cutting along buildings, fences
or roadsides.
Gearbox HP rating
25 - 55 HP to fit a large array of tractors
3/4” – 4” Cutting height
Gearbox Warranty
Low cutting height allows for scalping in grasses such as Bermuda prior to overseeding.
One year on all components
1” Cutting capacity
4 1/4” Rotor diameter
Reverse rotor rotation
Can cut small saplings.
Large rotor diameter protects against obstructions.
Reverse rotation brings the cut grass up and over the rotor for a cleaner discharge.
Cat. 4 driveline with over-
running clutch
Upon disengaging the PTO, the over-running clutch allows the driveline to quit turning, while
the clutch yoke, gearbox and rotor shaft slow down by their own inertia.
3 - “B” Section belts
“B” Section belts fit snug in the sheaves, and the multiple belts ensure positive transfer of
power.
3 Fine cut knives per hanger
High knife tip speed
Helps eliminate the peak and valley cut left with many fine cut blade arrangements.
Knife tip speed of 8,705 fpm for cleaner cut.
Adjustable rear panel
Rear panel adjusts to allow stronger discharge of material. Also aids in cleaning underside
of deck.
Baffles on the top inside of the
deck
Keeps the cut material from clumping together, ensuring an even distribution of clippings.
Height adjusting roller
Rear height adjusting roller with greaseable bearings and tapered ends to prevent gouging
during turns.
Scrapers
Standard scrapers on rear height adjusting roller.
FM2060 & FM2072 Flail Mowers 309-100M
3/25/08
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Troubleshooting
Section 7: Troubleshooting
Problem
Solution
!
CAUTION
Do not try to clean rear discharge area when mower is running. Bodily harm may occur!
Unplug and clean mower deck.
Remove belt guard shields and clean sheaves.
Replace belt
Belt slipping
Mow at full throttle (540 PTO rpm), check PTO speed and tractor engine.
Shift transmission to a lower gear.
Tighten belts.
Patches of uncut grass
Excessive vibration
Replace missing knives.
Replace knives
Replace drive belt.
Replace pulleys or align.
Remove belt guard shields & clean debris from belt area & sheaves.
Check lubricant level.
Raise cutting height by adjusting roller.
Change mowing pattern.
Reduce speed turns.
Gearbox noisy
Knives scalping grass
Shift to a lower gear.
Uneven cut
Level mower.
Replace missing knives.
Mow at full throttle (540 PTO rpm).
Shift to a lower gear.
Tractor loaded down by mower
Clean mower.
FM2060 & FM2072 Flail Mowers 309-100M
3/25/08
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Land Pride
Section 8: Appendix
Section 8: Appendix
Torque Values Chart
Bolt He a d Id e ntific a tion
Bolt He a d Id e ntific a tion
8.8
10.9
5.8
Class 5.8
Class 8.8
Class 10.9
Grade 2
Grade 5
Grade 8
1
3
in-tpi
1/4" - 20
1/4" - 28
N · m ft-lb N · m ft-lb N · m ft-lb
mm x pitch N · m ft-lb N · m ft-lb N · m ft-lb
7.4
8.5
15
5.6
11
8
16
12
M 5 X 0.8
4
3
6
5
9
7
6
13
10
18
14
M 6 X 1
7
5
11
8
15
11
5/16" - 18
5/16" - 24
3/8" - 16
3/8" - 24
7/16" - 14
7/16" - 20
1/2" - 13
1/2" - 20
9/16" - 12
9/16" - 18
5/8" - 11
5/8" - 18
3/4" - 10
3/4" - 16
7/8" - 9
11
24
17
33
25
M 8 X 1.25 17
12
26
19
36
27
17
13
26
19
37
27
M 8 X 1
18
33
13
28
21
39
29
27
20
42
31
59
44
M10 X 1.5
24
52
39
72
53
31
22
47
35
67
49
M10 X 0.75 39
M12 X 1.75 58
29
61
45
85
62
43
32
67
49
95
70
42
91
67
125
130
145
200
l215
315
335
405
485
610
900
93
49
36
75
55
105
145
165
210
235
285
325
510
570
820
905
78
M12 X 1.5
M12 X 1
60
44
95
70
97
66
49
105
115
150
165
205
230
360
405
585
640
875
955
76
105
120
155
170
210
240
375
420
605
670
90
66
105
145
155
225
240
310
350
440
650
760
830
77
105
150
160
230
245
300
355
450
665
75
55
85
M14 X 2
92
68
105
115
165
180
230
260
325
480
560
610
95
70
110
120
150
170
265
295
430
475
645
705
M14 X 1.5
M16 X 2
99
73
105
130
150
235
260
225
250
340
370
480
540
680
750
890
79
145
155
195
220
280
310
480
525
960
105
115
145
165
205
230
355
390
705
97
M16 X 1.5
M18 X 2.5
M18 X 1.5
M20 X 2.5
M20 X 1.5
M24 X 3
110
170
190
165
185
250
275
355
395
500
555
655
7/8" - 14
1" - 8
1050 780
1150 845
1230 910
1350 995
1750 1290
1960 1440
M24 X 2
1" - 12
M30 X 3.5
M30 X 2
1510 1120 2100 1550
1680 1240 2320 1710
1-1/8" - 7
1 1/8" - 12
1 1/4" - 7
1 1/4" - 12
1 3/8" - 6
1 3/8" - 12
1 1/2" - 6
1 1/2" - 12
1080 795
1210 890
1060 785
M36 X 3.5
1730 1270 2650 1950 3660 2700
1880 1380 2960 2190 4100 3220
1520 1120 2460 1820
1680 1240 2730 2010
1990 1470 3230 2380
2270 1670 3680 2710
2640 1950 4290 3160
2970 2190 4820 3560
M36 X 2
1
in-tpi = nominal thread diameter in inches-threads per in.
N· m = newton-meters
2
3
4
1010 745
1180 870
1330 980
ft-lb= foot pounds
mm x pitch = nominal thread diameter in millimeters x thread
pitch
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.
FM2060 & FM2072 Flail Mowers 309-100M
Download from Www.Somanuals.com. All Manuals Search And Download.
3/25/08
19
Land Pride
Section 8: Appendix
Warranty
Land Pride warrants to the original purchaser that this Land Pride product will
be free from defects in material and workmanship beginning on the date of
purchase by the end user according to the following schedule when used as
intended and under normal service and conditions for personal use.
Overall Unit and Driveline: One year Parts and Labor
Gearbox: One year on all components.
Belts and Blades: Considered wear items.
This Warranty is limited to the replacement of any defective part by Land
Pride and the installation by the dealer of any such replacement part, and does
not cover common wear items. Land Pride reserves the right to inspect any
equipment or parts which are claimed to have been defective in material or
workmanship.
This Warranty does not apply to any part or product which in Land Pride’s
judgment shall have been misused or damaged by accident or lack of normal
maintenance or care, or which has been repaired or altered in a way which
adversely affects its performance or reliability, or which has been used for a
purpose for which the product is not designed. Misuse also specifically includes
failure to properly maintain oil levels, grease points, and driveline shafts.
Claims under this Warranty should be made to the dealer which originally sold
the product and all warranty adjustments must be made through an authorized
Land Pride dealer. Land Pride reserves the right to make changes in materials
or design of the product at any time without notice.
This Warranty shall not be interpreted to render Land Pride liable for damages
of any kind, direct, consequential, or contingent to property. Furthermore, Land
Pride shall not be liable for damages resulting from any cause beyond its
reasonable control. This Warranty does not extend to loss of crops, any expense
or loss for labor, supplies, rental machinery or for any other reason.
No other warranty of any kind whatsoever, express or implied, is made
with respect to this sale; and all implied warranties of merchantability and
fitness for a particular purpose which exceed the obligations set forth in
this written warranty are hereby disclaimed and excluded from this sale.
This Warranty is not valid unless registered with Land Pride within 30 days
from the date of purchase by the end user.
FM2060 & FM2072 Flail Mowers 309-100M
Download from Www.Somanuals.com. All Manuals Search And Download.
3/25/08
21
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|