La Crosse Technology Clock 616 146A User Manual

Atomic Projection Alarm  
Model: 616-146A | Instruction Manual  
Introduction  
The Atomic Projection Alarm features radio-controlled time, indoor temperature, and moon phase on a  
simple, and easy to read display. Time and/or indoor temperature can be projected on a wall or ceiling.  
Use the integrated USB charging port to charge your will charge your smart phone, camera or other  
device when the Projection Alarm is plugged into a power outlet.  
Atomic Projection Alarm  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Features  
Projects time & indoor temp. on wall or ceiling  
Projection rotates in 90 degree increments  
Projection options: (1) Default: toggle between time and indoor temp.,  
(2) time only, or (3) indoor temperature only  
Time zones: Atlantic Time (AST), Eastern Time (EST), Central Time (CST), Mountain Time (MST),  
Pacific Time (PST), Alaskan Time (AKT) & Hawaiian Time (HAT)  
Light up display backlight with a press of a button using battery power OR continuous light with AC  
adapter (ON /OFF option)  
Backlight settings: High, Low and Off  
Charge devices with USB charging port: Output 0.5A  
Atomic time and date sets itself  
12/24 hour time with minutes  
Snooze alarm and alarm icon  
Calendar: day, date  
IN temperature (°F / °C) with trend arrow  
Moon Phase  
Low battery icon for clock  
Sits on desktop or tabletop  
5.0V AC adapter (included) for primary power and battery backup  
Battery life is over 24 months when using the AC adapter  
Initial Setup  
1. Insert A/C adapter into the wall outlet then into the display or insert 2 AAA batteries (not included)  
into the display (see Power the Atomic Projection Alarm). The Atomic Projection Alarm will light up  
and display time and indoor temperature.  
IMPORTANT: When operating on a/c power, the backlight, projection and USB charging port will turn off  
while the Projection Alarm searches for the WWVB signal, to avoid interference. The backlight and  
projection will return after the 2-10 minute search. Then the USB charging port will resume working.  
Do Not Mix Old and New Batteries  
Do Not Mix Alkaline, Standard, Lithium or Rechargeable Batteries  
Power the Atomic Projection Alarm  
The Projection Alarm can be powered by the 5-volt a/c adapter or by 2 AAA batteries.  
A/C power adapter:  
Insert enclosed 5-volt a/c power adapter into a wall outlet, then into the Atomic Projection Alarm.  
Battery  
Compartment  
5-Volt a/c adapter  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Batteries:  
1. Remove battery cover: Slide tab to the up and pull out to remove battery cover.  
2. Install two fresh AAA batteries according to the polarity markings.  
Do Not Mix Old and New Batteries  
Do Not Mix Alkaline, Lithium, Standard, or Rechargeable Batteries  
If the Atomic Projection Alarm does not display indoor temperature after 60 seconds, remove adapter and  
batteries, and wait for at least 60 seconds before repeating the setup process.  
IMPORTANT: When operating on a/c power, the backlight, projection and USB charging port will turn off  
while the Projection Alarm searches for the WWVB signal, to avoid interference. The backlight and  
projection will return after the 2-10 minute search. Then the USB charging port will resume working.  
WWVB Radio-controlled Time  
The NIST radio station, WWVB, is located in Ft. Collins, Colorado and transmits the exact time signal  
continuously throughout the United States at 60 kHz. The signal can be received up to 2,000 miles away  
through the internal antenna in the Atomic Projection Alarm. However, due to the nature of the Earth’s  
Ionosphere, reception is very limited during daylight hours. The Atomic Projection Alarm will search for a  
signal every night when reception is best. The WWVB radio station derives its signal from the NIST  
Atomic Clock in Boulder, Colorado. A team of atomic physicists continually measures every second of  
every day to an accuracy of ten billionths of a second a day. These physicists have created an  
international standard, measuring a second as 9,192,631,770 vibrations of a Cesium 133 atom in a  
vacuum. This atomic clock regulates the WWVB transmitter.  
WWVB Reception Icon  
A Tower with full signal strength will appear on screen in front of the date when the  
reception of atomic time is successful.  
The tower icon will show solid when the display has received the WWVB signal.  
No tower icon displayed. The display was unable to receive a signal at this time.  
Reposition the display for better signal reception or try again at bedtime.  
The display will start searching at UTC: 07:00 and if no reception on the first attempt they will try  
again at 08:00, 09:00 and 10:00. Each attempt will be at least 2 minutes and the most will be 10  
minutes.  
If there is no signal or too much interference the receiver will only be on for 2 minutes.  
If the signal is good it may catch a signal in ABOUT 2-3 minutes.  
If the signal is marginal it will try to catch a signal for up to 10 minutes.  
IMPORTANT: When operating on a/c power, the backlight, projection and USB charging port will turn off  
while the Projection Alarm searches for the WWVB signal, to avoid interference. The backlight and  
projection will return after the 2-10 minute search (which occurs during the late night or early morning  
hours). Then the USB charging port will resume working.  
Note: In case the Atomic Projection Alarm is not able to detect the WWVB-signal (disturbances,  
transmitting distance, etc.); the time may be manually set.  
Manual Signal Search:  
In normal mode, hold the RCC button until the reception icon appears to force a search of the WWVB  
signal. The WWVB icon will flash during the search. If this icon disappears after the 2-minute search,  
the radio time signal is not available at the moment.  
Recommended distance to any interfering sources like computer monitors or TV sets is a minimum of  
6 feet (2 meters).  
Within ferro-concrete rooms (basements, superstructures), the received signal is naturally weakened.  
In extreme cases, please place the unit close to a window and/ or point its front or back towards the  
Fort Collins, Colorado, transmitter.  
During nighttime, the atmospheric disturbances are usually less severe and reception is possible in  
most cases. A single daily reception is adequate to keep the accuracy deviation below 1 second.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Note: In case the atomic Projection Alarm is not able to detect the WWVB-signal (disturbances,  
transmitting distance, etc.), the time and date can be manually set (see “program menu).  
Function Buttons  
SNOOZE/LIGHT/HI/LOW/OFF (TOP)  
Button  
SET/°F/°C  
Press and Release Functions  
Move through program menu  
(setup)  
Hold 3 seconds  
Enter program menu, Set time,  
date, etc. (setup)  
Select temperature in °F/°C  
ALARM  
Once: View Alarm  
Alarm set  
Twice: Activate or Deactivate  
Alarm  
+/PROJ ON/OFF  
-/TIME SEARCH  
PROJECTION  
1 step forward (setup)  
Fast advance (setup) Turn  
Projection ON/OFF  
Fast backward ( setup) WWVB  
Search  
Change what is projected:  
Time/Indoor Temp alternating  
1 step backward (setup)  
Rotate Projection 90 degrees  
(default)  
Once:  
Time only  
Twice: Indoor Temp only  
Third time: Time/Outdoor  
Temp alternating (default)  
SNOOZE/LIGHT  
HI/LOW/OFF  
Once: Backlight low (a/c)  
Twice: Backlight OFF (a/c)  
3rd time: Backlight ON ( a/c)  
Activate backlight/projection 10  
seconds (battery power)  
Trigger snooze (alarm active)  
Program Menu  
The SET/°F/°C button will move through the items in the program menu. The +/PROJ ON/OFF or -/TIME  
SEARCH buttons will change these values.  
WWVB reception ON or OFF  
Time Zone (Seven Time Zones)  
Daylight Saving Indicator  
12/24 hour time format  
Manual time set (Hour, Minutes)  
Calendar set (Year, Month, Date)  
WWVB Reception:  
The WWVB time reception defaults to ON. To turn the WWVB reception OFF:  
ON  
1. Hold the SET/°F/°C button for 5 seconds.  
WWVB  
2. WWVB and ON will flash.  
3. Press and release the +/PROJ ON/OFF or -/TIME SEARCH buttons to turn this OFF.  
4. Confirm with the SET/°F/°C button and move to the Time Zone.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Time Zone  
This station offers seven time zones listed in letter format (default is EST):  
AST Atlantic Time  
EST Eastern Time  
CST Central Time  
MST Mountain Time  
PST Pacific Time  
AKT Alaskan Time  
HAT Hawaiian Time  
TIME  
ZONE  
EST  
1. EST will flash.  
2. Press and release the +/PROJ ON/OFF or -/TIME SEARCH buttons to select a different Time Zone.  
3. Confirm with the SET/°F/°C button and move to Daylight Saving Indicator.  
Daylight Saving Indicator:  
DST will default to the ON position as most of the country observes the DST change. If you live in an  
area does not observe the DST change, switch this to the OFF position.  
ON  
1. DST and ON will flash.  
2. Press and release the +/PROJ ON/OFF or -/TIME SEARCH buttons to turn DST to OFF.  
3. Confirm with the SET/°F/°C button and move to 12/24 hour time format.  
DST  
12 or 24-hour Time  
The Time may be displayed in 12-hour or 24-hour format. Default is 12-hour time.  
Note: When in 12-hour format AM or PM will show in front of the hour.  
12H  
1. 12H will flash.  
2. Press and release the +/PROJ ON/OFF or -/TIME SEARCH buttons to select 24-hour time.  
3. Confirm with the SET/°F/°C button and move to Set Time.  
Set Time:  
To set the time manually:  
1. The hour digit will flash.  
2. Press and release the +/PROJ ON/OFF or -/TIME SEARCH buttons to  
select the hour.  
3. Press and release the SET/°F/°C button to set the minutes.  
4. The minute’s digit will flash.  
5. Press and release the +/PROJ ON/OFF or -/TIME SEARCH buttons to select the minutes.  
6. Confirm with the SET/°F/°C button and move to Set Calendar.  
Set Calendar:  
The date default of the Atomic Projection Alarm is 1. 1. 2010.  
To set the calendar:  
1. The year will flash.  
2. Press and release the +/PROJ ON/OFF or -/TIME SEARCH buttons to set the year (between year  
2010-2039).  
2010  
3. Press the SET/°F/°C button again to confirm and to enter the month setting.  
4. The month will flash.  
5. Press and release the Press and release the +/PROJ ON/OFF or -/TIME SEARCH buttons to set the  
month.  
6. Press the SET/°F/°C button again to confirm and enter date setting.  
7. The date will flash.  
8. Press and release the +/PROJ ON/OFF or -/TIME SEARCH buttons to set the date.  
9. Confirm all calendar settings with the SET/°F/°C button to confirm and exit the program  
menu.  
1
M.
1
D  
Note: The day of the week will set automatically once the year, month and date are set.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Fahrenheit/Celsius:  
1. Press and release the SET/°C/°F button once to switch from Fahrenheit to Celsius.  
Alarm Set:  
Hold the ALARM button for 5 seconds to enter the alarm time set mode.  
1. The alarm hour digit will flash.  
2. Press and release the +/PROJ ON/OFF or -/TIME SEARCH buttons to  
select the hour.  
3. Press and release the SET/°F/°C button to set the minutes. The minute  
digits will flash.  
4. Press and release the +/PROJ ON/OFF or -/TIME SEARCH buttons to  
select the minutes.  
5. Confirm with the SET/°F/°C button and exit.  
6. The alarm icon will show after the minutes indicating the alarm is active.  
7. The alarm icon  
will flash when the alarm is sounding.  
Deactivate Alarm:  
1. Press and release the ALARM button once to show Alarm Time.  
2. Press and release the ALARM button to deactivate the Alarm. The alarm icon will disappear  
indicating the alarm is no longer active.  
Snooze  
1. When the alarm sounds, press the SNOOZE/LIGHT button to trigger snooze alarm for 10 minutes.  
The snooze icon Zz will flash when the snooze feature is active.  
2. To stop alarm for one day, press ALARM button, while in snooze mode. The alarm icon will remain  
solid.  
Note: When the alarm sounds, it continues for 2 minutes and then shuts off completely.  
Temperature Trend Arrows:  
The indoor temperature trend indicators are updated every 30 minutes. These trends represent  
temperature changes over the past three hours.  
Temperature rising more than 2°F /1°C in the past three hours  
Temperature has not changed more than 2°F /1°C in the past three hours  
Temperature falling more than 2°F /1°C in the past three hours  
The temperature trend indicators are shown next to the indoor temperature readings.  
Projection  
Battery Power:  
Press and release the SNOOZE/LIGHT button to show the projection for 10 seconds.  
Note: Projection will not display constantly when operating on battery power.  
A/C Power:  
Projection is displayed constantly unless turned off.  
OFF: Hold the +/PROJ ON/OFF button to turn the projection OFF while operating on a/c power.  
ON: Hold the +/PROJ ON/OFF button to turn the projection ON while operating on a/c power.  
Rotate Projection: Press and release the PROJECTION button to rotate projection image 90  
degrees. Press and release the PROJECTION button again to rotate another 90 degrees.  
Change Projection Mode: Hold, then release the PROJECTION button to switch projection modes.  
Watch the projection image to view the changes.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
o
o
Time and Indoor Temperature: alternate every 5 seconds (default)  
Time: Hold and release PROJECTION button  
Note: Both Time and Indoor Temperature will not show at the same time  
Projection Arm Rotation: The projection arm can be rotated 180 degrees to view the  
projection on the wall or ceiling.  
Backlight Intensity  
Press and release the SNOOZE/LIGHT button to adjust the brightness of the backlight:  
A/C Power  
The backlight is displayed constantly unless turned off.  
ON High intensity: The backlight is defaulted to HI when the Adapter is in use.  
ON Low intensity: Press and release SNOOZE/LIGHT button once  
OFF: Press and release SNOOZE/LIGHT button  
ON: Press and release SNOOZE/LIGHT button again  
Note: When the Adapter is NOT in use, the High/Low/On/Off features are not available.  
Battery Power  
Press the SNOOZE/LIGHT button to display the backlight for 10 seconds.  
USB Charge Port  
The integrated USB charging port (on back) will charge your smart phone, camera or other device when  
the Projection Alarm is plugged into a power outlet.  
Note: This is a power output (charging) port only. This port will not supply power to the Projection Alarm.  
Connect your existing USB charging cord for your external device to the USB charging port on the  
back of the Projection Alarm to begin to charge. Charging times will vary.  
Note: Check that your device will charge with the USB cord it came with. Many USB cords are  
for data transfer only, and cannot be used for charging.  
Output: 0.5A maximum current USB.  
Do NOT overload USB port.  
IMPORTANT: When operating on a/c power, the backlight, projection and USB charging port will turn off  
while the Projection Alarm searches for the WWVB signal, to avoid interference. The backlight and  
projection will return after the 2-10 minute search (which occurs during the late night or early morning  
hours). Then the USB charging port will resume working.  
Moon Phase  
The eight phases of the moon shown below are determined by the year, month, and date set on the  
Atomic Projection Alarm.  
New Moon occurs when the moon is between the earth and sun so the illuminated portion of the moon is  
on the back side facing the sun and we cannot see it. After a new moon the illuminated portion will  
increase or wax until the full moon occurs.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Full Moon occurs when the earth, moon, and sun are in approximate alignment, with the moon and the  
sun on opposite sides of the earth. The illuminated portion of the moon faces the earth, giving us  
complete visibility of one side of the entire moon. After a full moon the illuminated portion will decrease or  
wane until the new moon occurs.  
First Quarter and Last Quarter moons occur when the moon is at a 90 degree angle to the earth and  
sun. So we see half of the moon illuminated and half is in shadow.  
Waxing means growing or expanding illumination and happens after a new moon.  
Waning means decreasing illumination and occurs after a full moon.  
Crescent refers to the moon being less than half illuminated. Crescents can be waning or waxing.  
Gibbous describes a moon phase when more than half is illuminated. Gibbous can be waxing or waning.  
Note: With the moon shown against a light colored background, the phases will show opposite to a paper  
calendar. The segments that are highlighted will portray the part of the moon that is lit. For instance, the  
moon will be blank during a new moon and dark during a full moon.  
Position the Atomic Projection Clock  
1. The Atomic Projection Alarm has a wide base to sit on a desk or table.  
2. Choose a location 6 feet or more from electronics such as cordless phones, gaming systems,  
televisions, microwaves, routers etc.  
3. For best WWVB reception orientate the Atomic Projection Alarm with the front of the back facing Ft.  
Collins Atomicado.  
Care and Maintenance  
Do Not Mix Old and New Batteries  
Do Not Mix Alkaline, Standard, Lithium or Rechargeable Batteries  
Do not expose the Atomic Projection Alarm to extreme temperatures, vibration or shock.  
Keep Atomic Projection Alarm dry.  
Clean the Atomic Projection Alarm with a soft damp cloth. Do not use solvents or scouring agents.  
The Atomic Projection Alarm is not a toy. Keep it out of reach of children.  
The Atomic Projection Alarm is not to be used for medical purpose or for public information, but is  
determined for home use only.  
The specifications of this Atomic Projection Alarm may change without prior notice.  
Improper use or unauthorized opening of housing will void the warranty.  
If the unit does not work properly, change the batteries and/or check the a/c cord connection.  
Specifications  
Indoor:  
Temperature Range:  
Accuracy:  
Interval:  
+32°F to +122°F (0°C to 50°C)  
+/- 2 degrees Fahrenheit  
About every 30 seconds  
Power:  
Atomic Projection Alarm:  
5-volt a/c power adapter (included)  
Optional 2-AAA, IEC, LR3 batteries (not included)  
USB:  
Output 0.5 Amp maximum. Do not overload USB port.  
Battery Life:  
Atomic Projection Alarm  
Battery Backup:  
Battery life is over 24 months when using the AC adapter for primary  
power  
DIMENSIONS:  
Atomic Projection Alarm:  
5.23” W x 4.33” H x 1.96” D (133 x 110 x 50mm)  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Accuracy  
INDOOR TEMPERATURE:  
Operating temperature range = 32 F to 122 F (0C to 50C)  
Accuracy ± 2 degrees Fahrenheit 32 F to 122 F (0C to 50C)  
Resolution = 0.1 degree F  
Warranty Information  
La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing  
defects in materials and workmanship.  
This limited warranty begins on the original date of purchase, is valid only on products purchased and  
used in North America and only to the original purchaser of this product. To receive warranty service, the  
purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures.  
Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The  
original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology,  
Ltd or La Crosse Technology, Ltd’s authorized service center.  
La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated  
herein, with new or reconditioned parts or products if found to be defective during the limited warranty  
period specified above. All replaced parts and products become the property of La Crosse Technology,  
Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts and products assume the  
remaining original warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay  
all expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not  
covered by this warranty, or if a product is examined which is not in need or repair, you will be charged for  
the repairs or examination. The owner must pay any shipping charges incurred in getting the La Crosse  
Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. La Crosse  
Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA address  
only.  
The La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the  
following specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including  
the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must  
be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4)  
damage resulting from failure to follow instructions contained in the owner’s manual; (5) damage resulting  
from the performance of repairs or alterations by someone other than an authorized La CrossePrinted in China  
Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and  
uses that this product was not intended or (8) the products inability to receive a signal due to any source  
of interference.. This warranty covers only actual defects within the product itself, and does not cover the  
cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on  
misrepresentation by the seller or performance variations resulting from installation-related  
circumstances.  
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL,  
CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE  
OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR  
MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT  
OF CHILDREN’S REACH.  
This warranty gives you specific legal rights. You may also have other rights specific to the State. Some  
States do not allow the exclusion of consequential or incidental damages therefore the above exclusion of  
limitation may not apply to you.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
For warranty work, technical support, or information contact:  
La Crosse Technology, Ltd  
2817 Losey Blvd. S.  
La Crosse, WI 54601  
The complete instruction manual is available at:  
Contact Support: 1-608-782-1610  
Product Registration:  
Protected under U.S. Patents:  
5,978,738  
6,076,044  
6,597,990  
FCC Disclaimer  
This Device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and (2) the device must accept any interference  
received, including interference that may cause undesired operation.  
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE  
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS  
COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT  
All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or duplicated or  
processed using electronic, mechanical or chemical procedures without written permission of the  
publisher.  
This handbook may contain mistakes and printing errors. The information in this handbook is regularly  
checked and corrections made in the next issue. We accept no liability for technical mistakes or printing  
errors, or their consequences.  
All trademarks and patents are acknowledged.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

LG Electronics Freezer GR S552 User Manual
LG Electronics Refrigerator LFXC24726D User Manual
LG Electronics Refrigerator LSC27926SB User Manual
Linksys Network Card AG041 User Manual
LST Smoke Alarm B524IEFT 1 User Manual
Magnadyne Car Video System M135C 4 User Manual
Makita Impact Driver 6905B User Manual
Mattel Video Games H8856 0920 User Manual
Maverick Ventures Thermometer OT 3BBQ User Manual
Melissa Kitchen Grill 643 051 User Manual