TROUBLE SHOOTING
LOW BATTERY ICON
The low battery icon will show above the outdoor
temperature when it is time to change batteries.
•
If the Wireless Thermometer does not display the outdoor
temperature after 3 minutes, remove the batteries from both units
and repeat the setup process.
•
•
From normal display, hold the UP ARROW button for 3 seconds
to search for the outdoor temperature transmitter.
For optimal 433MHz signal reception, the outdoor transmitter
should be placed within 100 feet (30 meters) from the indoor
Wireless Thermometer.
MAXIMUM/MINIMUM TEMPERATURE READINGS
Wireless Thermometer
Model: 308-1910 | Instruction Manual
VIEW: Press and release the MIN/MAX button
once to show the maximum temperature
records. Press and release the MIN/MAX button
again to view the minimum temperatures. Press
and release the MIN/MAX button a third time to
return to current temperature.
The outdoor temperature reception icon will flash:
View temperature with a glance. Precise real-time indoor and
outdoor temperature with MIN/MAX readings in Fahrenheit or
Celsius, manual set time and alarm with snooze.
•
•
•
During initial setup, for up to three minutes, until it
connects with the transmitter.
About every minute afterwards as the wireless
thermometer receives an update.
When the UP ARROW button is held for 3 seconds to begin a
search for the transmitter.
RESET: Hold the MAX/MIN key for 2 seconds
to manually clear all the MIN/MAX records.
ALARM SET
SET TIME
From Time mode, press and release the ALARM button to switch to
Alarm Mode. The letters “AL” will appear between the hours and the
minutes. In Alarm Mode hold the ALARM button for 3 seconds to
enter alarm set mode.
In Time mode, hold the TIME button for 3 seconds to set the time.
•
HOUR: The Hour will flash. Press and release the ARROW
buttons to select the correct hour. Press and release the TIME
button once to move to the minutes.
•
HOUR: The Hour will flash. Press and release the ARROW
buttons to select the correct hour. Press and release the ALARM
button once to move to the minutes.
•
MINUTES: The Minutes will flash. Press and release the
ARROW buttons to select the correct minutes. Press and release
the TIME button once more to exit the program menu.
•
MINUTES: The Minutes will flash. Press and release the
ARROW buttons to select the correct minutes. Press and release
the ALARM button once more to exit the program menu.
SETUP INSTRUCTIONS STEP BY STEP
Note: When the alarm sounds, it continues for 2 minutes and then
shuts off completely.
STEP 1:
• Ensure that the transmitter is within 10 feet of the
Wireless Thermometer.
• Remove battery cover from TX19 transmitter.
• Insert 2 new AAA batteries (not included) into the
transmitter. Observe the correct polarity.
SNOOZE
SELECT THE TIME AND TEMPERATURE FORMAT
STEP 2:
The Thermometer either defaults to °C with 24 hr. time or °F with 12
hr. time. Both set up instructions are below:
• Remove battery cover from the Wireless
Thermometer (follow the arrow on the bottom of the battery
cover).
• Insert 2 new AAA batteries (not included) into
the back of the Wireless Thermometer.
Observe the correct polarity (see marking
inside the battery compartment).
•
When the alarm sounds, press the SNOOZE button to silence the
alarm for 5 minutes. The alarm icon
The snooze function can be repeated.
Press any other button to turn the alarm off for 24 hours.
will flash.
CELSIUS DEFAULT
FAHRENHEIT DEFAULT
•
•
•
•
Default temperature
•
•
Default temperature
reading is in Celsius.
From Time mode, press
and release the °F/°C
button to select Fahrenheit
temperature readout.
reading is in Fahrenheit.
From Time mode, press
and release the °F/°C
button to select Celsius
temperature readout.
ACTIVATE/DEACTIVATE ALARM
•
Within 3 minutes, the Wireless Thermometer
will show readings in the outdoor temperature
area on the wireless thermometer.
From Time mode, press and release the ALARM button to switch to
Alarm mode. The letters “AL” will appear between the hours and the
minutes.
ACTIVATE: In Alarm mode, press and release the UP ARROW
button to activate the alarm. The alarm icon will appear.
Note: Allow the Wireless Thermometer and
the transmitter to stay within 10 feet of each
other for the first 15 minutes of set up.
Do Not Mix Old and New Batteries
Do Not Mix Alkaline, Standard, Lithium or Rechargeable
Batteries
24 HOUR TIME
12 HOUR TIME
•
•
DEACTIVATE: In Alarm mode, with the bell icon visible, press and
release the UP ARROW button to deactivate the alarm. The bell icon
disappears.
•
•
Default time format is 24
hour time format.
From Time mode, press
and release the 12/24h
button to select 12 hour
time readout.
•
•
Default time format is 12
hour time format.
From Time mode, press
and release the 12/24h
button to select 24 hour
time readout.
Download from Www.Somanuals.com. All Manuals Search And Download.
|