617-1270 FAQS
The links below will work in most PDF viewers and link to the topic area by clicking the link. We
CONTENTS
617-1270 FAQS......................................................................................................................... 1
Batteries ................................................................................................................................... 1
Set Time Zone .......................................................................................................................... 2
Atomic Alarm Clock Factory Restart...................................................................................... 2
Manually Set Time/Date: Program Menu................................................................................ 3
Batteries
Explanation: Many problems are resolved with fresh batteries of the appropriate voltage. Many
items sent in under warranty work when tested with fresh batteries. Batteries manufactured this
year will have an expiration date 10 years (or more) in the future. Battery technology has
improved and batteries will maintain voltage longer in storage. However, the environment the
batteries reside in for the 10 years can deplete the power.
We suggest name brand Alkaline batteries for indoor displays.
A minimum voltage of 1.48V for each battery is necessary for proper performance.
Use batteries dated at least six years in advance of the current year. Batteries dated earlier
than six years from now may still work, but may be unstable in performance.
Good name brand batteries make less noise, which reduces the chance of RF (radio
frequency) interference from the battery compartment.
La Crosse Technology, Ltd
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Time is off by hours
alarm clock has not received a WWVB time signal in the past 24 hours.
Reposition the atomic alarm clock with the front or back facing Colorado.
Check that the Time Zone selected correctly reflects your location. Adjust the time zone in
the Program Menu.
Check that the DST indicator is correct for your location (most areas observe DST so this
should be ON). Adjust the DST indicator in the Program Menu.
Large buildings, metal roofed buildings and buildings or rooms full of electrical and/or radio
equipment make it difficult to receive the WWVB time signal.
Daylight Saving Time
Dependent on your location, position of the clock in your home, and atmospheric
interference, it may take up to 5 nights for the change from Daylight Savings Time to
Standard Time and vice-versa to occur.
you have received the WWVB signal from Ft Collins CO in the past 24 hours.
Check that the clock is in the correct Time Zone.
Check whether the DST indicator is ON or OFF. If the indicator is OFF the clock will not
change.
picking up the signal.
Position the atomic alarm clock in a window (with the front or back) facing Ft. Collins,
Colorado and leave for up to five nights. If you do not have a window facing this direction,
position the clock near an outside wall and point the unit in this general direction.
Manually Set Time/Date: Program Menu
The SET button will move through the program menu. The UP or DOWN buttons will change a
value.
12/24 HOUR TIME: 12Hr will flash. Press and release the UP or DOWN buttons to select
24hr. Confirm with the SET button and move to the next item.
HOUR: The hour will flash. Press and release the UP or DOWN buttons to select the correct
hour. Confirm with the SET button and move to the next item.
MINUTES: The minutes will flash. Press and release the UP or DOWN buttons to select the
correct minutes. Confirm with the SET button and move to the next item.
YEAR: The year will flash. Press and release + or - buttons to select the correct year.
Confirm with the SET button and move to the next item.
MONTH: The month will flash. Press and release the UP or DOWN buttons to select the
correct month. Confirm with the SET button and move to the next item.
DATE: The date will flash. Press and release the UP or DOWN buttons to select the correct
date. Confirm with the SET button and exit the program menu.
DAYLIGHT SAVING TIME: DST will flash and the word ON. Press and release the UP or
DOWN buttons to turn this to OFF if you do not observe DST. Confirm with the SET button
and move to the next item.
Note: The Day of the Week will set automatically after the year, month and date are set.
Note: If no buttons are pressed for 20 seconds, the set mode times out.
La Crosse Technology, Ltd
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
No WWVB Tower Icon
The atomic alarm clock has not received a WWVB time signal in the past 24 hours.
Position the atomic alarm clock for better reception.
Hold the WAVE button to send the Atomic alarm clock on a WWVB signal search at night.
Allow up to 5 nights to receive the time signal.
Set Time Alarm
Press and release the ALARM button once to show Alarm Time. The letters AL will appear
where the seconds display.
ALARM HOUR: Hold the ALARM button to enter alarm time setting mode. The Alarm Hour
will flash. Use the UP or DOWN buttons to set the Hour. Press and release the ALARM
button.
ALARM MINUTE: The Alarm Minutes will flash. Use the UP or DOWN buttons to set the
Minutes. Press and release the ALARM button to exit.
Activate/Deactivate Time Alarm
ACTIVATE:
Press and release the ALARM button to activate the alarm. The alarm icon (((●))) appears
when alarm is active.
DEACTIVATE:
Press and release the ALARM button to deactivate the alarm. The alarm icon will disappear
when alarm is inactive.
Note: When the alarm sounds, it will continue for two minutes then shut off.
Snooze Alarm
When the alarm sounds, press the SNOOZE/LIGHT button to trigger snooze alarm for 10
minutes.
The snooze icon Zz will flash when the snooze feature is active.
To stop alarm for one day, press ALARM button, while in snooze mode.
The alarm icon (bell) will remain solid.
Atomic Alarm Clock has distorted or frozen display
Explanation: On a brand new alarm clock, check for thin plastic film of printed scratch guard
that may be on the screen of the alarm clock. This thin piece of plastic has printed numbers for
store displays. When the batteries are installed, the “real” numbers show behind the printed
scratch guard and create distortion.
With all power removed, the alarm clock should be blank.
If numbers still appear, please check for scratch guard.
Power:
Check that the batteries are installed correctly.
This is generally a power related issue.
Remove batteries from alarm clock.
Press any button 20 times. Leave the batteries out of the display for 2 hours.
Insert and batteries into the alarm clock.
La Crosse Technology, Ltd
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Atomic Alarm Clock is blank: No letters, numbers or dashed lines
Check that the batteries are installed correctly.
Remove batteries from alarm clock.
Press any button 20 times. Leave the batteries out of the display for 2 hours.
Insert batteries into the alarm clock.
Atomic Alarm Clock drains batteries quickly
Test a new set of alkaline batteries. Write down the date of installation and the voltage of the
batteries.
When the batteries fail, please note the date and voltage again. This is helpful in
determining the problem.
Check for leaking batteries, which may damage the alarm clock.
Atomic Alarm Clock has missing segments
Explanation: When parts of numbers, letters, or pictures are missing on the display, it is often
power related.
With all power removed, the alarm clock should be blank.
If numbers still appear, please check for scratch guard.
Power:
Check that the batteries are installed correctly.
This is generally a power related issue.
Remove batteries from alarm clock.
Press any button 20 times. Leave the batteries out of the display for 2 hours.
Insert batteries into the alarm clock.
La Crosse Technology, Ltd
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
|