USER’S
GUIDE
LSI20160 Single Channel
Ultra160 SCSI to PCI
Host Adapter
Version 1.0
D e c e m b e r 2 0 0 1
®
DB15-000231-00
Download from Www.Somanuals.com. All Manuals Search And Download.
This document contains proprietary information of LSI Logic Corporation. The
information contained herein is not to be used by or disclosed to third parties
without the express written permission of an officer of LSI Logic Corporation.
LSI Logic products are not intended for use in life-support appliances, devices,
or systems. Use of any LSI Logic product in such applications without written
consent of the appropriate LSI Logic officer is prohibited.
Document DB15-000231-00, First Edition (December 2001)
This document describes the LSI Logic LSI20160 Single Channel Ultra160 SCSI
to PCI Host Adapter and will remain the official reference source for all
revisions/releases of this product until rescinded by an update.
LSI Logic Corporation reserves the right to make changes to any products herein
at any time without notice. LSI Logic does not assume any responsibility or
liability arising out of the application or use of any product described herein,
except as expressly agreed to in writing by LSI Logic; nor does the purchase or
use of a product from LSI Logic convey a license under any patent rights,
copyrights, trademark rights, or any other of the intellectual property rights of
LSI Logic or third parties.
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
TRADEMARK ACKNOWLEDGMENT
The LSI Logic logo design, LVDlink, SCRIPTS, SDMS, SureLINK, and TolerANT
are registered trademarks or trademarks of LSI Logic Corporation. All other
brand and product names may be trademarks of their respective companies.
MH
iii
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
This book is the primary reference and user’s guide for the LSI Logic
LSI20160 Single Channel Ultra160 SCSI to PCI Host Adapter. It contains
a complete functional description for the LSI20160 board as well as
complete physical and electrical specifications.
Audience
This document assumes that you have some familiarity with SCSI
protocol and related support devices and will benefit persons installing
and using the LSI20160.
Organization
This document has the following chapters and appendix:
•
•
•
•
Chapter 1, Describing the LSI20160, defines the interfaces and
characteristics of the LSI20160.
Chapter 2, Installing the LSI20160, provides both quick and detailed
installation instructions.
Chapter 3, Technical Specifications, describes the physical and
operational environments of the LSI20160.
Appendix A, Glossary of Terms and Abbreviations, provides
definitions of various terminology that is referenced throughout this
user’s guide.
LSI20160 Single Channel Ultra160 SCSI to PCI Host Adapter
v
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Publications
PCI Storage Device Management System SDMS™ 4.0 User’s Guide,
Version 11, Order Number S14007.B
LSI53C1000 PCI to Ultra160 SCSI Controller Technical Manual,
Version 2.1, Order Number S14050.A
Revision History
Revision
Date
Remarks
1.0
12/01
Final version.
vi
Preface
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Chapter 1
Describing the LSI20160
1.1
1.2
General Description
Features
1-4
1-5
1.2.1
1.2.2
1.2.3
1.2.4
PCI Interface
SCSI Interface
Board Characteristics
SCSI Activity LED Interface
1.3
Ultra160 SCSI Benefits
1.3.1
1.3.2
1.3.3
Cyclic Redundancy Check (CRC)
1.4
1.5
1.6
SureLINK™ Ultra160 SCSI Domain Validation Benefits
®
Chapter 2
Installing the LSI20160
2.1
2.2
Quick Installation Procedure
Detailed Installation Procedure
2.2.1
2.2.2
2.2.3
2.2.4
2.2.5
2.2.6
Selecting a PCI Slot
Inserting the Host Adapter
Setting SCSI IDs
2-4
2-20
2.3
Completing the Installation
Chapter 3
Technical Specifications
3.1 Physical Environment
3.1.1 Physical Characteristics
3-1
3-1
LSI20160 Single Channel Ultra160 SCSI to PCI Host Adapter
vii
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1.2
3.1.3
3.1.4
3.1.5
Electrical Characteristics
3-4
3-7
3-8
Thermal, Atmospheric Characteristics
Electromagnetic Compliance
Safety Characteristics
3.2
3.3
Operational Environment
3.2.1
3.2.2
3.2.3
The SCSI Interface
The LED Interface
Appendix A
Glossary of Terms and Abbreviations
Customer Feedback
viii
Contents
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Figures
2.1
2.2
2.3
2.4
2.5
Hardware Connections for the LSI20160
Inserting the Host Adapter
2-4
SCSI Cables
Internal SCSI Ribbon Cable to Host Adapter
Internal SCSI Ribbon Cable to Internal SCSI Device
Connection
2.6
2.7
2.8
2.9
Connecting Additional Internal SCSI Devices
SCSI LED Connector
2-13
2-14
2-16
2-17
3-2
External Cable to Host Adapter
2.10 External Cable to External SCSI Device
2.11 Multiple External SCSI Devices Chained Together
2.12 Internal SCSI Device Termination
2.13 External SCSI Device Termination
3.1
LSI20160 Mechanical Drawing
ix
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables
2.1
3.1
3.2
3.3
3.4
3.5
3.6
SCSI ID Record
3-5
3-6
3-7
3-8
3-9
Maximum Power Requirements
PCI Connector J1 (Front)
PCI Connector J1 (Back)
SCSI Interface
LED Connector J3 Pinout
Subsystem ID and Subsystem Vendor ID
xi
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
xii
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Describing the
LSI20160
PCI Host Adapter interface to PCI computer systems and includes these
topics:
•
•
•
•
Section 1.4, “SureLINK™ Ultra160 SCSI Domain Validation Benefits,”
page 1-5
•
•
Section 1.5, “LVDlink™ Technology Benefits,” page 1-5
Section 1.6, “TolerANT® Technology Benefits,” page 1-6
1.1 General Description
The LSI Logic LSI20160 provides one SCSI-3, Ultra160 SCSI interface
to PCI computer systems that require BIOS support on the add-in SCSI
adapter. Installing this adapter in your PCI system allows connection of
SCSI devices over a SCSI bus.
The LSI20160 provides one Ultra160 SCSI channel. The LSI20160
supports Low Voltage Differential (LVD) and Single-Ended (SE) SCSI.
This board supports Fast/Ultra/Ultra2 SCSI devices as well as the newest
Ultra160 SCSI devices.
The LSI Logic Storage Device Management System (SDMS™) software
operates the board. The design of the board does not prevent other SCSI
software from being used with it. BIOS support for this host adapter is
incorporated on the board in a 128 Kbyte Flash device. The onboard
controller for the LSI20160 is the LSI53C1000 PCI to Ultra160 SCSI
Controller.
LSI20160 Single Channel Ultra160 SCSI to PCI Host Adapter
1-1
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
The LSI53C1000 contains a SCSI SCRIPTS™ processor that permits
both DMA and SCSI commands to be fetched from host memory or
internal SCRIPTS RAM. Algorithms written in SCSI SCRIPTS control the
actions of the SCSI and DMA cores. The SCRIPTS processor executes
complex SCSI bus sequences independently of the host CPU.
In addition to this guide there is another reference that you will find
useful. The LSI Logic PCI Storage Device Management System
SDMS 4.0 User’s Guide contains product information and installation
instructions.
1.2 Features
This section provides an overview of the PCI interface, the SCSI
interface, and board characteristics for the LSI20160.
1.2.1 PCI Interface
The PCI interface operates as a 32-bit DMA bus master, where the
connection is made through the J1 edge connector.
The PCI interface includes these features:
•
•
•
Complies with PCI Local Bus Specification, Revision 2.2
Complies with PC99
Complies with PCI Bus Power Management Specification,
Revision 1.1
•
•
Supports 32-bit 33 MHz word data bursts with variable burst lengths
Bursts 4/8, 8/16, 16/32, or 32/64 Qword/Dword transfers across the
PCI bus
•
Bursts up to 264 Mbytes/s (@ 33 MHz) with zero wait-state bus
master data
•
•
•
Supports the PCI Cache Line Size (CLS) register
Prefetches up to 8 Dwords of SCRIPTS instructions
Supports PCI Write and Invalidate, Read Line, and Read Multiple
commands
•
Supports universal 3.3 V and 5 V PCI bus signaling environment
1-2
Describing the LSI20160
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2.2 SCSI Interface
The SCSI interface is made through connectors J2 and J4. Figure 2.1
shows the location of these connectors. The SCSI interface includes
these features:
•
•
Provides one wide Ultra160 SCSI channel
Provides two connectors:
–
–
68-pin VHDCI for the external connection
68-pin high density for the internal connection
•
•
•
Supports SE and LVD signaling: 16-bit SE or LVD interfaces
Supports LVD/SE termination
Supports Fast, Ultra, Ultra2, and Ultra160 data transfer capability
–
Ultra160 SCSI LVD synchronous transfers at up to 160 Mbytes/s
•
Supports Domain Validation, Double Transition (DT) data transfers,
and Cyclic Redundancy Check (CRC)
•
•
Supports variable block size and scatter/gather data transfers
Protects nondata phases with Asynchronous Information Protection
(AIP)
•
Supports two termination control options:
–
Use manual shunts on connector J2 and J4 to disable
termination
–
Provide software control using GPIO3 to enable or disable the
terminators
•
Supplies SCSI termination power (TERMPWR) source with
autoresetting circuit breaker
•
•
•
•
Includes SCSI Plug and Play
Provides Flash EEPROM for BIOS configuration storage
Includes 8 Kbytes internal RAM for SCRIPTS instruction storage
Provides a SCSI activity LED connector (J3)
Features
1-3
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2.3 Board Characteristics
The board characteristics are
•
PCI board dimensions
Approximately 4.721 x 2.536 inches
•
•
Universal 32-bit PCI card edge connector
Standard bracket available
1.2.4 SCSI Activity LED Interface
The J3 connector is a four-wire arrangement on the LSI20160 that
represents the SCSI activity LED interface. Table 3.5 on page 3-8 lists
the signal name and pin numbers for this LED interface.
1.3 Ultra160 SCSI Benefits
Ultra160 SCSI is an extension of the SPI-3 draft standard that allows
faster synchronous SCSI data transfer rates than Ultra2 SCSI. When
enabled, Ultra160 SCSI performs 80 megatransfers per second resulting
in approximately double the synchronous data transfer rates of Ultra2
SCSI. The LSI53C1000 performs 16-bit, Ultra160 SCSI synchronous
data transfers as fast as 160 Mbytes/s. This advantage is most
noticeable in heavily loaded systems or large block size applications
such as video on-demand and image processing.
1.3.1 Double Transition (DT) Clocking
The Ultra160 data transfer speed is accomplished using DT clocking.
DT clocking refers to transferring data on both rising and falling edges of
the request and acknowledge signals. Double-edge clocking doubles
data transfer speeds without increasing the clock rate.
1-4
Describing the LSI20160
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3.2 Cyclic Redundancy Check (CRC)
Ultra160 SCSI includes CRC which offers higher levels of data reliability
by ensuring complete integrity of transferred data. CRC is a 32-bit
scheme, referred to as CRC-32. CRC is guaranteed to detect all single
bit errors, any two bits in error, or any combination of errors within a
single 32-bit range.
1.3.3 Asynchronous Information Protection (AIP)
The LSI53C1000 also supports AIP, which protects all nondata phases,
including command, status, and messages. CRC, along with AIP,
provides end-to-end protection of the SCSI I/O.
1.4 SureLINK™ Ultra160 SCSI Domain Validation Benefits
SureLINK software represents the very latest SCSI interconnect
management solution. It ensures robust and low risk Ultra160 SCSI
implementations by extending the Domain Validation guidelines
documented in the ANSI T10 SPI-3 specifications. Domain Validation
verifies that the system is capable of transferring data at Ultra160
speeds, allowing it to renegotiate to lower speed and bus width if
necessary.
SureLINK software is the control for the manageability enhancements in
the LSI53C1000. Fully integrated in the SDMS software solution,
SureLINK software provides Domain Validation at boot time, as well as
throughout system operation.
1.5 LVDlink™ Technology Benefits
The LSI20160 supports LVD for SCSI, a signaling technology that
increases the reliability of SCSI data transfers over longer distances than
are supported by SE SCSI. The low current output of LVD allows the I/O
transceivers to be integrated directly onto the chip. LVDlink technology
lowers the amplitude of noise reflections and allows higher transmission
frequencies. LVD provides a long-term migration path to even faster
SCSI transfer rates without compromising signal integrity, cable length,
or connectivity.
SureLINK™ Ultra160 SCSI Domain Validation Benefits
1-5
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Important: All bus devices must be LVD or SE. If a High Voltage
Differential (HVD) device is detected, the board puts the
SCSI bus in the high impedance state and shuts down.
®
1.6 TolerANT Technology Benefits
The LSI20160 features TolerANT technology, which includes active
negation on the SCSI drivers and input signal filtering on the SCSI
receivers. The benefits of TolerANT technology include increased
immunity to noise when the signal is going HIGH, better performance
due to balanced duty cycles, and improved fast SCSI transfer rates. In
addition, TolerANT SCSI devices do not cause glitches on the SCSI bus
at power up or power down, so other devices on the bus are also
protected from data corruption.
When it is used with the LVDlink transceivers, TolerANT technology
provides excellent signal quality and data reliability in real world cabling
environments. TolerANT input signal filtering is a built-in feature of the
LSI53C1000 device as well as all LSI Logic SCSI devices.
1-6
Describing the LSI20160
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Installing the LSI20160
This chapter provides instructions on how to install the LSI20160 and
includes these topics:
•
•
•
Section 2.1, “Quick Installation Procedure,” page 2-1
Section 2.2, “Detailed Installation Procedure,” page 2-2
Section 2.3, “Completing the Installation,” page 2-20
2.1 Quick Installation Procedure
This section provides an overview of the installation procedure. If you are
an experienced computer user with prior host adapter installation and
SCSI bus setup experience, this section may sufficiently describe the
procedure for you. If you prefer more detailed guidance for installing the
LSI20160, proceed to Section 2.2, “Detailed Installation Procedure.”
For safe and proper installation, check the user’s manual supplied with
your computer and perform the following steps.
Step 1. Ground yourself before handling the host adapter board.
Step 2. Remove the LSI20160 from its packing and examine it for any
damage.
Figure 2.1 shows an example of this host adapter board.
Step 3. Switch off and unplug the system.
Step 4. Open your PC cabinet.
Step 5. Locate the PCI slots on your computer.
Step 6. Insert the LSI20160 into the selected PCI slot.
Step 7. Connect the internal and external SCSI peripherals.
LSI20160 Single Channel Ultra160 SCSI to PCI Host Adapter
2-1
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 8. Connect the LED cable to J3 on your SCSI host adapter, if you
wish to connect the LED to the SCSI LED connector.
Step 9. Terminate the SCSI bus.
The SCSI bus requires proper termination and no duplicate
SCSI IDs.
Step 10. Set the peripheral SCSI IDs.
Step 11. Make any configuration changes.
Step 12. Close your PC cabinet cover.
Step 13. Make all external SCSI bus connections.
Step 14. Refer to the PCI Storage Device Management System
SDMS 4.0 User’s Guide (or the guide for the software you will
use) to load the driver software for your particular operating
system.
This section provides step-by-step instructions for installing the
LSI20160, and connecting it to your SCSI peripherals. If you are
experienced in these tasks, you may prefer to use the preceding
Section 2.1, “Quick Installation Procedure.”
2.2.1 Before You Start
Before starting, read through the steps defined within the detailed
installation procedure. If you are not confident that you can perform the
tasks as described in this section, LSI Logic suggests getting assistance.
The SCSI host adapter acts on your computer’s behalf as the host to
your suite of SCSI peripherals. Each chain of SCSI peripheral devices
and their host adapter work together and are referred to as a SCSI bus.
Each SCSI host adapter that you install can act as host for up to
15 peripheral devices, not including the adapter itself.
2-2
Installing the LSI20160
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.2 Selecting a PCI Slot
For safe and proper installation, check the user’s manual supplied with
your computer and perform the following steps.
Step 1. Ground yourself before removing the host adapter board from
its package.
Step 2. Remove the LSI20160 from its packing and verify it is not
damaged.
Figure 2.1 shows an example of this host adapter board.
Step 3. Switch off and unplug the system.
Step 4. Remove the cabinet cover on your computer to access the PCI
slots.
Caution:
Ground yourself by touching a metal surface before
handling boards. Static charges on your body can damage
electronic components. Handle plug-in boards by the edge;
do not touch board components or gold connector contacts.
The use of a static ground strap is recommended.
Step 5. Locate the PCI slots on your computer.
Refer to the user’s manual supplied with your computer to
confirm the location of the PCI slots. Also, the LSI20160
requires a PCI slot that allows bus master operation and
provides 3.3 Volts. Figure 2.2 is a representative drawing of a
computer mainboard.
Detailed Installation Procedure
2-3
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.3 Inserting the Host Adapter
Perform the following steps to install the LSI20160 in your PC mainboard.
Step 1. Remove the blank bracket panel on the back of the computer
aligned with the PCI slot you intend to use.
Save the bracket screw.
the PCI slot.
Make sure the edge connector is properly aligned before
pressing the board into place. The bracket around connector J2
should fit where the blank bracket panel was removed. Refer to
Figures 2.1 and 2.2.
Figure 2.1 Hardware Connections for the LSI20160
68-pin Internal
High Density SCSI
Connector J4
Busy LED
Connector J3
68-pin VHDCI
External SCSI
Connector J2
LSI20160 to PCI Bus
Edge Connector J1
Note:
You may notice that the components on a PCI host adapter
face the opposite way from non-PCI adapter boards you
have in your system. This is correct. The board is keyed to
go in only one way.
2-4
Installing the LSI20160
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3. Secure the bracket with the bracket screw before making the
internal and external SCSI bus connections. Figure 2.2 shows
an example on how to insert your host adapter.
Figure 2.2 Inserting the Host Adapter
Bracket Screw
32-bit Slots
64-bit Slots
Detailed Installation Procedure
2-5
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.4 Connecting SCSI Peripherals
All internal SCSI bus connections to the LSI20160 can be made with an
unshielded, 68-conductor ribbon cable (see Figure 2.3). One side of this
cable is marked with a color to indicate the pin-1 side. The connectors
on this cable are keyed to ensure proper pin-1 connection. Some internal
cables come with an LVD/SE terminator on one end. This end should be
furthest from the host adapter.
All external SCSI bus connections to the LSI20160 are made with
shielded, 68-conductor cables (see Figure 2.3). The connectors on this
cable are always keyed to ensure proper pin-1 connection.
Figure 2.3 SCSI Cables
SCSI Cable for Internal Connections
68-pin
High Density
SCSI Cable for External Connections
68-pin
VHDCI
2-6
Installing the LSI20160
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.4.1 Making Internal SCSI Bus Connections
This section provides step-by-step instructions for making internal SCSI
bus connections. If you only have external connections, skip to
Section 2.2.4.3, “Making External SCSI Bus Connections.”
Step 1. Plug a 68-pin connector on the end of the internal SCSI ribbon
cable into connector J4. Figure 2.4 illustrates how to make this
connection.
Figure 2.4 Internal SCSI Ribbon Cable to Host Adapter
Detailed Installation Procedure
2-7
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2. Plug the 68-pin connector on the other end of the internal SCSI
ribbon cable into the SCSI connector on the internal SCSI
device.
Pin 1 must match on all connections. The lead in the cable
adjacent to pin 1 is colored. Figure 2.5 illustrates a connection
to an internal SCSI device.
Figure 2.5 Internal SCSI Ribbon Cable to Internal SCSI Device
Connection
If you have more than one internal SCSI device, you must have
a cable with at least as many connectors as devices.
2-8
Installing the LSI20160
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3. Plug in any additional internal SCSI devices, as required. Refer
to the example in Figure 2.6.
Figure 2.7 illustrates the connection of multiple internal SCSI
devices chained together. Make sure to match pin 1 on all
connections.
Figure 2.6 Connecting Additional Internal SCSI Devices
Detailed Installation Procedure
2-9
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2.7 Multiple Internal SCSI Devices Chained Together
2.2.4.2 Making Activity LED Connection
Most PC cabinets are designed with a front panel LED to indicate bus
activity. It may already be connected to an existing IDE controller. If you
want, you can connect the LED to the SCSI LED connector.
Connect the LED cable to J3 on your SCSI host adapter, as shown in
Figure 2.8.
The Busy LED connector J3 is not keyed. The J3 connector is a 4-pin
one row right angle header. Some LED cables have only two wires. In
this case, place the connector on one end of J3. If the LED does not light
during SCSI bus activity, you may have to rotate the LED cable 180˚ on
J3 or move it to the other end of the jack.
2-10
Installing the LSI20160
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
After the correct connection is established, the front panel LED indicates
activity on the SCSI bus. Refer to Table 3.5 on page 3-8 for connector
pinout information.
Figure 2.8 SCSI LED Connector
LED
Cable
LED
Connector J3
Detailed Installation Procedure
2-11
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.4.3 Making External SCSI Bus Connections
This section provides step-by-step instructions for making external SCSI
bus connections.
Step 1. Plug the 68-pin VHDCI connector on one end of a shielded
external high density cable (see Figure 2.3) into the host
adapter connector J2.
This connector is exposed on the back panel of your computer.
Figure 2.9 illustrates where this connection is made.
Figure 2.9 External Cable to Host Adapter
2-12
Installing the LSI20160
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2. Plug the 68-pin connector on the other end of the shielded
external SCSI cable into the SCSI connector on your external
SCSI device.
Figure 2.10 illustrates a connection to an external SCSI device.
Figure 2.10 External Cable to External SCSI Device
Detailed Installation Procedure
2-13
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3. Chain any additional SCSI devices together with shielded
external SCSI cables.
Figure 2.11 shows an example of multiple external SCSI
devices that are chained together.
Figure 2.11 Multiple External SCSI Devices Chained Together
2-14
Installing the LSI20160
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.5 SCSI Bus Termination
The devices making up the SCSI bus are connected serially (chained
together) with SCSI cables. The first and last physical SCSI devices
connected on the ends of the SCSI bus must have their terminators
active. All other SCSI devices on the bus must have their terminators
removed or disabled.
Termination control has two options which allow a different termination
mode:
•
Termination can be disabled by placing a manual shunt over the
post. When the shunt is off, the terminator is active. When the shunt
is on the post, the terminator is disabled.
•
Termination can be enabled or disabled for a specific channel using
software control with GPIO3.
LVD peripheral devices are normally terminated with external
terminators, but are sometimes set with jumpers or with a switch on the
peripheral. Refer to the peripheral manufacturer’s instructions and to the
user’s manual for your computer for information on how to identify the
terminator setting of each device and how to change it.
The LSI20160 automatically controls SCSI bus termination for two
different bus configurations (see Figure 2.1). The two bus configurations
are
•
•
Termination on
Termination off
You can disable termination in two ways:
•
•
Use BIOS software control, where the BIOS termination option is
changed from Automatic to Off.
Manually place a shunt on the post of the respective jumpers, J2DIS
and J4DIS.
Detailed Installation Procedure
2-15
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.5.1 Internal SCSI Terminations
you must terminate the last internal device on the SCSI bus. You must
disable the termination on all other devices. Termination on your host
adapter is automatically enabled in this case if there are no external
SCSI devices connected through J2.
Figure 2.12 shows an example of how termination is determined for this
SCSI bus configuration.
Figure 2.12 Internal SCSI Device Termination
Last Device on
Chain-
Termination
Enabled
Does Not End Chain-
Termination Disabled
Host Adapter
Automatically
Terminated
2-16
Installing the LSI20160
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.5.2 External SCSI Terminations
adapter, you must terminate the last external device on the SCSI bus.
Termination on all other devices must be disabled. Termination on your
host adapter is automatically enabled in this case if there are no internal
devices connected through J4.
Figure 2.13 shows an example of how termination is determined for this
SCSI bus configuration on your host adapter.
Figure 2.13 External SCSI Device Termination
Last Device on
Chain-Termination
Enabled
Does Not End
Chain-Termination
Disabled
Host Adapter
Automatically
Terminated
Detailed Installation Procedure
2-17
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.6 Setting SCSI IDs
You must set each SCSI device and the host adapter to a separate SCSI
ID. The IDs are 0 through 7 for an 8-bit bus and 0 through 15 for a 16-bit
bus. SCSI ID 7 is the preset host adapter setting, giving it the highest
priority on the SCSI bus. If you plan to boot your computer from a hard
disk drive on the SCSI bus, that drive should have SCSI ID 0, or the
lowest SCSI ID on the bus. The PCI Storage Device Management
System SDMS 4.0 User’s Guide explains how to set your host adapter
ID using the SCSI BIOS Configuration Utility.
The peripheral device SCSI IDs are usually set with jumpers or with a
switch on the peripheral. Refer to the peripheral manufacturer’s
instructions and to the user’s manual for your computer to determine the
ID of each device and how to change it. No duplication of SCSI IDs is
allowed on a SCSI bus.
Step 1. Determine the SCSI ID of each device on the SCSI bus. Note
any duplications.
Step 2. Make any necessary changes to the SCSI IDs and record the
IDs for future reference. Correct any duplications at this time.
Table 2.1 on page 2-19 is provided as a place to keep this
record.
2-18
Installing the LSI20160
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Completing the Installation
Before replacing the cover on your computer, review this installation
procedure check list. This can save you effort later.
Verify Installation Procedures
Done
Host adapter connection in PCI bus slot secure
Internal SCSI bus connections secure (pin-1 continuity)
External SCSI bus connections secure
Proper SCSI bus termination established
Unique SCSI IDs set and recorded for each device
Step 1. Replace the cabinet cover on your computer.
Step 2. Plug in all power cords, and switch on power to all devices and
your computer.
Step 3. Wait for your computer to boot up.
Step 4. Refer to the LSI Logic PCI Storage Device Management
System SDMS 4.0 User’s Guide (or the guide for the software
you will use) to load the driver software for your particular
operating system and to change the configuration of your host
adapter, if needed.
2-20
Installing the LSI20160
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Technical
Specifications
This chapter discusses the physical environment associated with the
LSI20160. It includes a mechanical drawing of this board, which is shown
in Figure 3.1. It also includes these topics:
•
•
•
Section 3.1, “Physical Environment,” page 3-1
Section 3.2, “Operational Environment,” page 3-4
Section 3.3, “Subsystem ID and Subsystem Vendor ID,” page 3-9
3.1 Physical Environment
This section discusses the physical, electrical, thermal, and safety
characteristics of the LSI20160. Additionally, this board is compliant with
electromagnetic standards set by the FCC.
3.1.1 Physical Characteristics
The dimensions of the LSI20160 are 4.721 x 2.536 inches. Edge
connector J1 makes the PCI connection. The component height on the
top and bottom of the LSI20160 follows the PCI specification.
Connector J4 is a 68-pin high density connector that makes the internal
SCSI connection. Connector J2 is a 68-pin VHDCI connector that makes
the external SCSI connection. The J2 connector extends through the
standard bracket, which is attached to the face of the connector outside
of the cabinet where the LSI20160 is installed. Connector J3 provides
connection to the computer’s drive activity LED. It is a 4-pin, one-row,
right-angle header.
LSI20160 Single Channel Ultra160 SCSI to PCI Host Adapter
3-1
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3.1 LSI20160 Mechanical Drawing
J4
J3 LED
Channel A
Ultra160 SCSI LVD only
LSI53C1000
J1T-PCI
J2
Channel A
Ultra160 SCSI LVD/SE
Note:
•
•
•
•
•
•
J1: PCI 32-bit universal type board edge connector.
J2: 68-pin VHDCI connector for external SCSI connection.
J4: 68-pin high density internal SCSI connection.
J3: 4-pin low density unshrouded right-angle LED connector.
Subsystem Vendor ID is 1000.
Subsystem ID is 1060.
3.1.2 Electrical Characteristics
The LSI20160 maximum power requirements that include SCSI
TERMPWR under normal operation are shown in Table 3.1:
Table 3.1
Maximum Power Requirements
+5 V DC
5%
5%
1.3 A
Over the operating range 0–55 °C (with SCSI
TERMPWR, supplied to external connection)
+5 V DC
0.40 A
Over the operating range 0–55 ˚C (without
SCSI TERMPWR, supplied to external
connection)
+3.3 V DC 5%
1.00 A
Over the operating range 0–55 ˚C
The PCI PRSNT1 and PRSNT2 pins are set to indicate a 7.5 W maximum
configuration.
3-2
Technical Specifications
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Under abnormal conditions, such as a short on SCSI TERMPWR, + 5 V
current may be higher. At temperatures of at least 25 °C, a current of
8 A is sustained no longer than 0.5 seconds before the self-resetting
TERMPWR short circuit protection device opens.
3.1.3 Thermal, Atmospheric Characteristics
The thermal, atmospheric characteristics of the LSI20160 are:
•
•
•
Temperature range: 0 °C to 55 °C (dry bulb)
Relative humidity range: 5% to 90% noncondensing
Maximum dew point temperature: 32 °C
The following parameters define the storage and transit environment for
the LSI20160:
•
•
Temperature range: − 45 °C to + 105 °C (dry bulb)
Relative humidity range: 5% to 90% noncondensing
3.1.4 Electromagnetic Compliance
This board is tested to and meets class B regulatory requirements for the
United States, Canadian, European, Japanese, and Australian markets.
This board carries the appropriate markings (FCC, CE, VCCI, C-Tick)
indicating such compliance.
3.1.5 Safety Characteristics
The bare board meets or exceeds the requirements of UL flammability
rating 94 V0. The bare board is also marked with the supplier’s name or
trademark, type, and UL flammability rating. Since this board is installed
in a PCI bus slot, all voltages are below the SELV 42.4 V limit.
Physical Environment
3-3
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Operational Environment
The LSI20160 is designed for use in PCI computer systems with a
standard bracket type. The SDMS software operates the board, but the
design of the board does not prevent the use of other software. An on-
board Flash memory device allows you to use BIOS code and open boot
code support through PCI and a serial EEPROM.
3.2.1 The PCI Interface
The PCI interface operates as a 32-bit DMA bus master. The connection
is made through edge connector J1, which provides connections on both
the front and back of the board. The signal definitions and pin numbers
conform to the PCI Local Bus Specification, Revision 2.2 standard. The
signal assignments appear in Table 3.2, Table 3.3, and Table 3.4.
Note:
The LSI20160 uses 3.3 V pins to run the LSI53C1000 and
some other parts. The LSI20160 requires 3.3 V from the
PCI + 3.3 V power rail for proper operation.
3-4
Technical Specifications
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Table 3.2
PCI Connector J1 (Front)
Signal Name
Pin
Signal Name
Pin
−12 V
TCK
1
AD17
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
2
2
C_BE2
GND
GND
TDO
+5 V
+5 V
3
2
4
IRDY
5
+3.3 V
2
6
DEVSEL
2
2
INTB
7
GND
2
2
INTD
8
LOCK
2
2
GND(PRSNT1 )
RESERVED
9
PERR
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
+3.3 V
2
2
GND(PRSNT2 )
SERR
KEYWAY
KEYWAY
RESERVED
GND
+3.3 V
2
C_BE1
AD14
GND
AD12
AD10
CLK
GND
2
REQ
M66EN (LVD)
KEYWAY
KEYWAY
AD08
3 V/5 V
AD31
AD29
GND
AD07
AD27
AD25
+3.3 V
+3.3 V
AD05
AD03
2
C_BE3
GND
AD23
GND
AD01
3 V/5 V
2
AD21
AD19
+3.3 V
ACK64
+5 V
+5 V
1. Shaded lines are not connected.
2. Active LOW signal.
Operational Environment
3-5
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
)
1
Table 3.3
PCI Connector J1 (Back)
Signal Name
Pin
Signal Name
Pin
2
TRST
1
AD16
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
+12 V
TMS
TDI
2
+3.3 V
FRAME
GND
2
3
4
2
+5 V
5
TRDY
2
INTA
6
GND
2
2
INTC
7
STOP
+5 V
8
+3.3 V
RESERVED
3 V/5 V
9
SDONE
2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
SBO
RESERVED
KEYWAY
KEYWAY
RESERVED
GND
PAR
AD15
+3.3 V
AD13
2
RST
3 V/5 V
AD11
2
GNT
GND
GND
AD09
RESERVED
AD30
KEYWAY
KEYWAY
2
+3.3 V
AD28
C_BE0
+3.3 V
AD06
AD04
GND
AD26
GND
AD24
IDSEL
+3.3 V
AD22
AD02
AD00
3 V/5 V
2
AD20
REQ64
GND
+5 V
+5 V
AD18
1. Shaded lines are not connected.
2. Active LOW signal.
3-6
Technical Specifications
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2.2 The SCSI Interface
The SCSI interface conforms to ANSI X 3T10.11/1142. The SCSI
interface operates as 16-bit, synchronous or asynchronous, SE or LVD,
and supports Ultra160 SCSI protocols. Arbitration is supported for 8-bit
(at lower SCSI speeds) and 16-bit. Active SE or LVD SCSI termination
is provided automatically. The LSI20160 supplies the SCSI termination
power.
Connector J2 makes the external connection, which provides LVD/SE
SCSI termination. Connector J4 makes the internal connection, which
only provides LVD SCSI termination.
Table 3.4 shows the signal assignments for J2 and J4.
Table 3.4
SCSI Interface
Signal Name
Pin Signal Name Pin Signal Name Pin
SD12+
SD13+
SD14+
SD15+
SDP1+
SD0+
1
2
3
4
5
6
7
8
9
SACK+
SRST+
SMSG+
SSEL+
SC_D+
SREQ+
SI_O+
SD8+
24 SD7−
25 SDP−
26 GND
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
27 Cable_prnt
28 TERMPWR
29 TERMPWR
30 N/C
SD1+
SD2+
31 GND
SD3+
SD9+
32 SATN−
33 GND
SD4+
10 SD10+
11 SD11+
12 SD12−
13 SD13−
14 SD14−
15 SD15−
16 SDP1−
17 SD0−
18 SD1−
19 SD2−
20 SD3−
21 SD4−
22 SD5−
23 SD6−
SD5+
34 SBSY−
35 SACK−
36 SRST−
37 SMSG−
38 SSEL−
39 SC_D−
40 SREQ−
41 SI_O−
42 SD8−
43 SD9−
44 SD10−
45 SD11−
46
SD6+
SD7+
SDP+
GND
DIFFSENS
TERMPWR
TERMPWR
N/C
GND
SATN+
GND
SBSY+
Operational Environment
3-7
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2.3 The LED Interface
The LSI20160 LED interface is a four-wire arrangement that allows you
to connect an LED harness to the board. The GPIO0_FETCH line has a
maximum output low voltage of 0.4 V and minimum output low current of
16 mA. It is driven low to complete the circuit when a harness with an
LED is attached. The J3 connector provides the LED connection on the
LSI20160. Table 3.5 lists the signal and pin numbers for the LED
interface.
Table 3.5
LED Connector J3 Pinout
Signal Name
Pin
A_LED+
A_LED−
A_LED−
A_LED+
1
2
3
4
3-8
Technical Specifications
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Subsystem ID and Subsystem Vendor ID
Table 3.6 provides the Subsystem ID and System Vendor ID for the
LSI20160. The serial EEPROM on this board contains the ID numbers.
During system initialization, the system loads the ID numbers into the
Subsystem Vendor ID and Subsystem ID registers of the LSI20160 SCSI
Controller (the LSI53C1000). For more information on the operation of
the Subsystem Vendor ID and Subsystem ID registers, refer to the
LSI53C1000 PCI to Ultra160 SCSI Controller Technical Manual.
Table 3.6
Subsystem ID and Subsystem Vendor ID
Subsystem
ID
Subsystem Vendor ID
Subsystem ID
1000
1060
Subsystem ID and Subsystem Vendor ID
3-9
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
3-10
Technical Specifications
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Glossary of Terms and
Abbreviations
160/m
An industry initiative extension of the Ultra160 SCSI specification that
requires support of Double Transition Clocking, Domain Validation, and
Cyclic Redundancy Check (CRC).
Active
Termination
The electrical connection required at each end of the SCSI bus,
composed of active voltage regulation and a set of termination resistors.
Ultra, Ultra2, and Ultra160 SCSI require active termination.
Address
AIP
A specific location in memory, designated either numerically or by a
symbolic name.
Asynchronous Information Protection provides error checking for
asynchronous, nondata phases of the SCSI bus.
Asynchronous
Data Transfer
One of the ways data is transferred over the SCSI bus. It is slower than
synchronous data transfer.
BIOS
Basic Input/Output System. Software that provides basic read/write
capability. Usually kept as firmware (ROM based). The system BIOS on
the mainboard of a computer is used to boot and control the system. The
SCSI BIOS on your host adapter acts as an extension of the system
BIOS.
Bit
A binary digit. The smallest unit of information a computer uses. The
value of a bit (0 or 1) represents a two-way choice, such as on or off,
true or false, and so on.
Bus
A collection of unbroken signal lines across which information is
transmitted from one part of a computer system to another. Connections
to the bus are made using taps on the lines.
LSI20160 Single Channel Ultra160 SCSI to PCI Host Adapter
A-1
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Bus Mastering
A high-performance way to transfer data. The host adapter controls the
transfer of data directly to and from system memory without interrupting
the computer’s microprocessor. This is the fastest way for multitasking
operating systems to transfer data.
Byte
A unit of information consisting of eight bits.
CISPR
A special international committee on radio interference (Committee,
International and Special, for Protection in Radio).
Configuration
CRC
Refers to the way a computer is setup; the combined hardware
components (computer, monitor, keyboard, and peripheral devices) that
make up a computer system; or the software settings that allow the
hardware components to communicate with each other.
Cyclic Redundancy Check is an error detection code used in Ultra160
SCSI. Four bytes are transferred with the data to increase the reliability
of data transfers. CRC is used on the Double Transition (DT) Data-In and
DT Data-Out phases.
CPU
Central Processing Unit. The “brain” of the computer that performs the
actual computations. The term Microprocessor Unit (MPU) is also used.
DMA Bus
Master
A feature that allows a peripheral to control the flow of data to and from
system memory by blocks, as opposed to PIO (Programmed I/O) where
the processor is in control and the flow is by byte.
Device Driver
A program that allows a microprocessor (through the operating system)
to direct the operation of a peripheral device.
Differential SCSI A hardware configuration for connecting SCSI devices. It uses a pair of
lines for each signal transfer (as opposed to Single-Ended SCSI which
references each SCSI signal to a common ground).
DMI
Desktop Management Interface.
Domain
Validation
Domain Validation is a software procedure in which a host queries a
device to determine its ability to communicate at the negotiated Ultra160
data rate.
Double
Transition (DT)
Clocking
In DT Clocking data is sampled on both the asserting and deasserting
edge of the REQ/ACK signal. DT Clocking may only be implemented on
an LVD SCSI bus.
A-2
Glossary of Terms and Abbreviations
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dword
A double word is a group of four consecutive bytes or characters that are
stored, addressed, transmitted, and operated on as a unit. The lower two
address bits of the least significant byte must equal zero in order to be
Dword aligned.
EEPROM
EISA
Electronically Erasable Programmable Read Only Memory. A memory
chip typically used to store configuration information. See NVRAM.
Extended Industry Standard Architecture. An extension of the 16-bit ISA
bus standard. It allows devices to perform 32-bit data transfers.
External SCSI
Device
A SCSI device installed outside the computer cabinet. These devices are
connected in a continuous chain using specific types of shielded cables.
Fast-20
The SCSI Trade Association (STA) supports the use of “Ultra SCSI” over
the term “Fast-20”. Please see Ultra SCSI.
Fast-40
The SCSI Trade Association (STA) supports the use of “Ultra2 SCSI”
over the term “Fast-40”. Please see Ultra2 SCSI.
Fast SCSI
A standard for SCSI data transfers. It allows a transfer rate of up to
10 Mbytes/s over an 8-bit SCSI bus and up to 20 Mbytes/s over a 16-bit
SCSI bus.
FCC
Federal Communications Commission.
File
A named collection of information stored on a disk.
Firmware
Software that is permanently stored in ROM. Therefore, it can be
accessed during boot time.
Hard Disk
Host
A disk made of metal and permanently sealed into a drive cartridge. A
hard disk can store very large amounts of information.
The computer system in which a SCSI host adapter is installed. It uses
the SCSI host adapter to transfer information to and from devices
attached to the SCSI bus.
Host Adapter
A circuit board or integrated circuit that provides a SCSI bus connection
to the computer system.
Internal SCSI
Device
A SCSI device installed inside the computer cabinet. These devices are
connected in a continuous chain using an unshielded ribbon cable.
A-3
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
IRQ
ISA
Interrupt Request Channel. A path through which a device can get the
immediate attention of the computer’s CPU. The PCI bus assigns an IRQ
path for each SCSI host adapter.
Industry Standard Architecture. A type of computer bus used in most
PCs. It allows devices to send and receive data up to 16 bits at a time.
Kbyte
Kilobyte. A measure of computer storage equal to 1024 bytes.
Local Bus
A way to connect peripherals directly to computer memory. It bypasses
the slower ISA and EISA buses. PCI is a local bus standard.
Logical Unit
A subdivision, either logical or physical, of a SCSI device (actually the
place for the device on the SCSI bus). Most devices have only one
logical unit, but up to eight are allowed for each of the eight possible
devices on a SCSI bus.
LUN
LVDlink
Low Voltage Differential link allows greater Ultra2 SCSI device
connectability and longer SCSI cables. LVDlink lowers the amplitude of
noise reflections and allows higher transmission frequencies. Detailed
information may be found in Section 1.5, “LVDlink™ Technology
Benefits,” page 1-5.
Mainboard
A large circuit board that holds RAM, ROM, the microprocessor, custom
integrated circuits, and other components that make a computer work. It
also has expansion slots for host adapters and other expansion boards.
Main Memory
The part of a computer’s memory which is directly accessible by the CPU
(usually synonymous with RAM).
Mbyte
Megabyte. A measure of computer storage equal to 1024 kilobytes.
Motherboard
See Mainboard. In some countries, the term Motherboard is not
appropriate.
Multitasking
The executing of more than one command at the same time. This allows
programs to operate in parallel.
Multithreading
The simultaneous accessing of data by more than one SCSI device. This
increases the data throughput.
A-4
Glossary of Terms and Abbreviations
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
NVRAM
NonVolatile Random Access Memory. Actually an EEPROM
(Electronically Erasable Read Only Memory chip) used to store
configuration information. See EEPROM.
Operating
System
A program that organizes the internal activities of the computer and its
peripheral devices. An operating system performs basic tasks such as
moving data to and from devices, and managing information in memory.
It also provides the user interface.
Parity Checking A way to verify the accuracy of data transmitted over the SCSI bus. The
parity bit in the transfer is used to make the sum of all the 1 bits either
odd or even (for odd or even parity). If the sum is not correct, the
information may be retransmitted or an error message may appear.
Passive
The electrical connection required at each end of the SCSI bus,
Termination
composed of a set of resistors. It improves the integrity of bus signals.
PC99
A set of design standards that developers must comply with to be
Windows NT compatible.
PCI
Peripheral Component Interconnect. A local bus specification that allows
connection of peripherals directly to computer memory. It bypasses the
slower ISA and EISA buses.
Peripheral
Devices
A piece of hardware (such as a video monitor, disk drive, printer, or
CD-ROM) used with a computer and under the computer’s control. SCSI
peripherals are controlled through a SCSI host adapter.
Pin-1
Orientation
The alignment of pin 1 on a SCSI cable connector and the pin-1 position
on the SCSI connector into which it is inserted. External SCSI cables are
always keyed to insure proper alignment, but internal SCSI ribbon cables
sometimes are not keyed.
PIO
Programmed Input/Output. A way the CPU can transfer data to and from
memory using the computer’s I/O ports. PIO is usually faster than DMA,
but requires CPU time.
Port Address
Also Port Number. The address through which commands are sent to a
host adapter board. This address is assigned by the PCI bus.
Port Number
Queue Tags
See Port Address.
A way to keep track of multiple commands that allow for increased
throughput on the SCSI bus.
A-5
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
RAM
Random Access Memory. The computer’s primary working memory in
which program instructions and data are stored and are accessible to the
CPU. Information can be written to and read from RAM. The contents of
RAM are lost when the computer is turned off.
RISC Core
ROM
LSI Logic SCSI chips contain a RISC (Reduced Instruction Set
Computer) processor, programmed through SCRIPTS microcode.
Read Only Memory. Memory from which information can be read but not
changed. The contents of ROM are not erased when the computer is
turned off.
SCAM
SCSI
SCSI Configured AutoMatically. A method to automatically allocate SCSI
IDs using software when SCAM compliant SCSI devices are attached.
Small Computer System Interface. A specification for a high-performance
peripheral bus and command set. The original standard is referred to as
SCSI-1.
SCSI-2
The SCSI specification which adds features to the original SCSI
standard.
SCSI-3
The SCSI specification which adds features to the SCSI-2 standard.
SCSI Bus
A host adapter and one or more SCSI peripherals connected by cables
in a linear chain configuration. The host adapter may exist anywhere on
the chain, allowing connection of both internal and external SCSI
devices. A system may have more than one SCSI bus by using multiple
host adapters.
SCSI Device
SCSI ID
Any device that conforms to the SCSI standard and is attached to the
SCSI bus by a SCSI cable. This includes SCSI host adapters and SCSI
peripherals.
A way to uniquely identify each SCSI device on the SCSI bus. Each
SCSI bus has eight available SCSI IDs numbered 0 through 7 (or 0
through 15 for Wide SCSI). The host adapter usually gets the highest ID
(7 or 15) giving it priority to control the bus.
SCSI SCRIPTS
A SCSI programming language that works with the SCRIPTS processor.
The SCRIPTS processor fetches SCRIPTS instructions from system
memory to control processor operation.
A-6
Glossary of Terms and Abbreviations
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
SCRIPTS
Processor
The SCRIPTS processor allows users to fine tune SCSI operations with
regard to unique vendor commands or new SCSI specifications. The
SCRIPTS processor fetches SCRIPTS instructions from system memory
to control processor operation.
SDMS
Storage Device Management System. An LSI Logic software product that
manages SCSI system I/O.
Single-Ended
SCSI
A hardware specification for connecting SCSI devices. It references each
SCSI signal to a common ground. This is the most common method (as
opposed to differential SCSI which uses a separate ground for each
signal).
STA
SCSI Trade Association. A group of companies that cooperate to
promote SCSI parallel interface technology as a viable mainstream I/O
interconnect for commercial computing.
SureLINK
The domain validation method developed and used by LSI Logic.
SureLINK provides three levels of integrity checking: Basic (level 1),
Enhanced (level 2), and Margined (level 3).
Synchronous
Data Transfer
One of the ways data is transferred over the SCSI bus. Transfers are
clocked with fixed frequency pulses. This is faster than asynchronous
data transfer. Synchronous data transfers are negotiated between the
SCSI host adapter and each SCSI device.
System BIOS
TolerANT
Controls the low-level POST (Power-On Self-Test), and basic operation
of the CPU and computer system.
A technology developed and used by LSI Logic to improve data integrity,
data transfer rates, and noise immunity through the use of active
negation and input signal filtering.
Ultra SCSI
A standard for SCSI data transfers. It allows a transfer rate of up to
20 Mbytes/s over an 8-bit SCSI bus and up to 40 Mbytes/s over a 16-bit
SCSI bus. SCSI Trade Association (STA) supports using the term “Ultra
SCSI” over the older term “Fast-20”.
Ultra2 SCSI
A standard for SCSI data transfers. It allows a transfer rate of up to
40 Mbytes/s over an 8-bit SCSI bus, and up to 80 Mbytes/s over a
16-bit SCSI bus. SCSI Trade Association (STA) supports using the term
“Ultra2 SCSI” over the term “Fast-40”.
A-7
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Ultra160 SCSI
A standard for SCSI data transfers. It allows a transfer rate of up to
160 Mbytes/s over a 16-bit SCSI bus.
VCCI
VDE
Voluntary Control Council for Interference.
Verband Deucher Elektroniker (Association of German Electrical
Engineers).
VHDCI
Very High Density Cable Interconnect.
Virtual Memory
Wide SCSI
Space on a hard disk that can be used as if it were RAM.
A SCSI-2 feature allowing 16-bit or 32-bit transfers on the SCSI bus. This
dramatically increases the transfer rate over the standard 8-bit SCSI bus.
Wide Ultra SCSI The SCSI Trade Association (STA) term for SCSI bus width 16-bits, SCSI
bus speed maximum data rate 40 Mbytes/s.
Wide Ultra2
SCSI
The SCSI Trade Association (STA) term for SCSI bus width 16-bits, SCSI
bus speed maximum data rate 80 Mbytes/s.
Word
A two byte (or 16-bit) unit of information.
A-8
Glossary of Terms and Abbreviations
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
asynchronous information protection
feature of Ultra160 SCSI 1-5
features
board characteristics 1-4, 3-1
PCI interface 1-2, 3-4
SCSI interface 1-3, 3-7
B
board characteristics 1-4, 3-1
board software 1-1
bracket type 1-4, 3-4
bus configurations 2-15
additional internal devices 2-9
making 2-7
to internal device 2-8
internal SCSI device terminations 2-16
C
completing the installation
using a checklist 2-20
connecting the SCSI peripherals 2-6
connector
J1 3-1
J2 3-1
J3 3-8
J4 3-1
cyclic redundancy check
feature of Ultra160 SCSI 1-5
cables 2-10
J3 connector 3-8
D
LSI20160 host adapter
connecting SCSI peripherals 2-6
features 1-2 to 1-4
descriptions
PCI interface 1-2, 3-4
SCSI activity LED interface 1-4, 3-8
SCSI interface 1-3, 3-7
detailed installation procedure 2-2 to 2-5
domain validation
inserting 2-4
LED interface 1-4
maximum power requirements 3-2
operational environment 3-4 to 3-8
physical environment 3-1 to 3-3
selecting a PCI slot 2-3
LSI53C1000 device
benefits 1-5
double transition clocking
feature of Ultra160 SCSI 1-4
performing Ultra160 SCSI 1-4
using TolerANT technology 1-6
LVD peripheral devices 2-15
LVD SCSI termination 3-7
LVDlink technology 1-5
E
EEPROM
for configuration storage 1-3
electrical characteristics 3-2
electromagnetic compliance 3-3
external SCSI bus connections
external chaining 2-14
making 2-12
M
maximum power 3-2
mechanical drawing 3-2
to external device 2-13
external SCSI terminations 2-17
LSI20160 Single Channel Ultra160 SCSI to PCI Host Adapter
IX-1
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
benefits 1-6
O
operational environment 3-4 to 3-8
P
UL flammability rating 3-3
Ultra160 SCSI 1-4
PCI board dimensions 1-4, 3-1
PCI connector 3-5 to 3-6
PCI interface 1-2, 3-4
PCI slot
asynchronous information protection 1-5
benefits 1-4
double transition 1-4
selecting 2-3
peripheral devices 2-18
physical environment 3-1 to 3-3
preset host adapter setting
SCSI ID 2-18
SureLINK software 1-5
Q
quick installation procedure 2-1 to 2-2
S
safety characteristics 3-3
SCSI
activity LED interface 1-4
bus termination 2-15
cables 2-6
connecting peripherals 2-6
devices using TolerANT technology 1-6
disabling termination 2-15
drivers
active negation 1-6
interface 1-3, 3-7
making external connections 2-12 to 2-14
making internal connections 2-7 to 2-10
plug and play 1-3
receivers
input signal filtering 1-6
SE or LVD termination 3-7
setting IDs 2-18
termination power 1-3
SCSI BIOS configuration utility
using 2-18
serial EEPROM
containing system ID numbers 3-9
signal assignments
PCI interface 3-4
SCSI interface 3-7
software
operating the board 1-1, 2-20
standard bracket 3-1
subsystem ID 3-9
subsystem vendor ID 3-9
SureLINK software
for domain validation 1-5
T
termination
disabling 2-15
external SCSI connections 2-17
internal SCSI connections 2-16
SCSI bus 2-15
SE or LVD SCSI 3-7
thermal, atmospheric characteristics 3-3
IX-2
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Feedback
We would appreciate your feedback on this document. Please copy the
following page, add your comments, and fax it to us at the number
shown.
If appropriate, please also fax copies of any marked-up pages from this
document.
Important: Please include your name, phone number, fax number, and
company address so that we may contact you directly for
clarification or additional information.
Thank you for your help in improving the quality of our documents.
LSI20160 Single Channel Ultra160 SCSI to PCI Host Adapter
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Reader’s Comments
Fax your comments to:
LSI Logic Corporation
Technical Publications
M/S E-198
Fax: 408.433.4333
Please tell us how you rate this document: LSI20160 Single Channel
Ultra160 SCSI to PCI Host Adapter User’s Guide. Place a check mark in
the appropriate blank for each category.
Excellent Good Average Fair
Poor
____
____
____
____
____
Completeness of information
Clarity of information
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
Ease of finding information
Technical content
Usefulness of examples and
illustrations
Overall manual
____
____
____
____
____
What could we do to improve this document?
If you found errors in this document, please specify the error and page
number. If appropriate, please fax a marked-up copy of the page(s).
Please complete the information below so that we may contact you
directly for clarification or additional information.
Name
Date
Telephone
Title
Fax
Department
Company Name
Street
Mail Stop
City, State, Zip
Customer Feedback
Copyright © 2001 by LSI Logic Corporation. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
You can find a current list of our U.S. distributors, international distributors, and sales
offices and design resource centers on our web site at
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|