LG Electronics Washer WF 2409KTb User Manual

JUN. 2002 PRINTED IN KOREA  
P/No.:3828EA3013E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WASHING MACHINE  
SERVICE MANUAL  
CAUTION  
Before servicing the washer, Read the safety precautions in the manual.  
MODELS : WF-T10(~3)0(~2,6)1(~5)TP(H,E,F)(S,3)  
WF-T802/T852(A)/T853A  
WF-T(F/C)1091~3, 1191~3T(C/H/P)  
WF-T(F/C)1022, 1122, 1001T(C/H/P)  
WF-T1268TH, 2409KTb, 2602kTa  
WF-T1491TP, T11292TP, T1292TP, T1291TP  
WF-T1081TP, T1592TP, T1593TP  
WF-T1241TP, T1133TH  
WF-G15KTB, G13KTC, B15KTB, B13KTC  
WF-T1400TH, T1022TPX  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. SPECIFICATIONS  
WF-T10(~3)0(~2,6)1(~5)TP(H,E,F)(S,3), WF-T802/T852(A)/T853A  
WF-T(F/C)1091~3/1191~3T(C/H/P), WF-T(F/C)1022/1122/1001T(C/H/P)  
WF-T1268TH/2409KTb/ 2602kTa/T1491TP/T1022THX/T1133TH  
Model  
WF-T1081TP/T1491TP/T11292TP/T1292TP/T1291TP/LA-1499ST/T1592TP/T1593TP/T1241TP  
WF-G15KTB/G13KTC/WF-B15KTB/B13KTC/WF-T1400TH/T1022TPX  
Power Sourse  
Input  
Refer to rating label on the back of Washer  
Refer to rating label on the back of Washer  
Refer to rating label on the back of Washer  
Stainless  
Capacity  
Inner Tub  
0.3kgf/cm2 ~ 8kgf/cm2  
Inlet Water Pressure  
250V, 6A for 220~240V/50Hz  
125V, 12A for100~127V/60Hz  
Rating of Fuse  
Spin Speed  
Dim.  
50Hz : 700 50 / 60Hz : 740 50  
Refer to rating label on the back of Washer  
Refer to rating label on the back of Washer  
Fuzzy, Economy, Jean, Wool  
Weight  
Program  
Water Level  
7 Stages  
Reservation  
Available for 3 ~ 48 Hr  
B.P Sensor (S.F Switch)  
Unbalance Switch  
Lid Interlock Switch  
Child Lock  
B.P Sensor (S.F Switch)  
Applied  
Double  
Lint Filter  
Applied  
Softener Dispenser  
Detergent Dispenser  
Bleach Inlet  
Applied  
Applied  
Applied  
Auto Power Off  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. INSTALLATION INSTRUCTIONS  
2-1. HOW TO ADJUST LEVEL  
1 ·InInssttaallllathtieonwaasrheear on flat and firm  
surface.  
Checking level  
2
·Open the lid, and check if the washer is  
correctly leveled by looking down from  
the top.  
Adjustable leg  
Turn the adjustable legs to set the washer  
horizontal (2 EA).  
How to use the adjusting plates  
·
Use the adjusting plates to level the washer when the  
adjustable legs cannot cover the gap.  
Improper installation of the washer may cause noise and malfunctioning.  
1. The ventilating openings in the base area must not be obstructed be carpeting  
when the washing machine is installed on a carpeted floor.  
CAUTION  
2. Install the washing machine on a level and firm surface, any tilt should be  
°
less than 1 .  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Checking slope  
Confirming level  
3
5
· Place the washer to original position  
· If installation surface is tilted, the  
and confirm the level.  
washer will be shaken.  
Distance between drain hose and the wall  
Horizontal setting  
4
·
Distance between drain hose and the wall  
should be more than 10 cm, and the distance  
between the other part and the wall should be  
·Lift up the front of the washer and  
adjust level by turning the adjustable  
legs clockwise or using the adjusting  
plate.  
more than 2 cm.  
More than 10cm  
More than 2cm  
More than 2cm  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-2. CONNECTING WATER SUPPLY HOSE  
Before connecting Water Supply Hose to water tap, check your hose type  
and choose correct instruction. Water Supply Hose may vary according to  
the country.  
Make sure connect blue inlet hose to cold water tab, and orange inlet hose  
to hot water tab.  
Connecting Water Supply Hose to water tap  
Normal Type  
Normal tab without thread & screw type inlet hose.)  
Rubber packing  
Untighten the screw  
1
Untighten the screw of the connector so  
that the tap can be placed in the middle.  
Fixing the connector to the tap  
Push the upper connector up till the rubber  
packing is in tight contact with the tap. Then  
tighten the 4 screws.  
2
Attach the water supply hose to the connector  
Push the water supply hose vertically  
upwards so that the rubber seal within the  
hose can adhere completely to the tap.  
3
4
Connector  
Water supply hose  
Fixing the connector of connector and water supply hose  
Attach the water supply hose to the  
connector and then tighten it by screwing it  
to the right.  
Check the connection of water supply hose and the connector  
5
After connecting the hose, open the tap to  
check for any water leakage.  
In case of water leakage, close the tap and  
start again from step 1  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
One Touch Type  
(NORMAL TAB WITHOUY THREAD & ONE TOUCH TYPE INLET HOSE.)  
Separate Middle connector from Water Supply Hose  
1
Middle  
Separate Middle connector from the Water  
Supply Hose by pulling the Pressing Rod and  
the Pressing Handle that is attached to the  
Water Supply Hose while pressing them.  
Fixed Stiicker  
connector  
Pressing Handle  
Pressing Rod  
Water Supply Hose  
Loosen the fixed nuts to connect the connector to the tap  
2
Untighten the screw of the connector so that  
the tap can be placed in the middle.  
Rubber packing  
Screw  
Fixed sticker  
Note  
Guide plate  
In case the tap is large.  
If the tap diameter is too large or is square,  
open the 4 screw and take out the guide  
plate and follow step 1.  
Rubber packing  
Fixing Connectors to the Tap  
Push the upper connector up till the rubber  
packing is in tight contact with the tap. Then  
tighten the 4 screws.  
3
4
Connector  
Fixing Upper Connector and Middle Connector  
Connector  
Remove the fixed sticker in between the  
Upper and Middle Connectors. Tighten the  
connectors by holding one connector and  
twist middle connector to the right.  
Connector  
Middle  
Connector  
Middle  
Connector  
Fixed sticker  
5
6
Connecting Middle Connector and Water Supply Hose  
Press down the pressing rod of the Water  
Supply Hose which was separated from  
Pressing rod  
Pressing handle  
middle connector(refer to Step1) and then  
join it to the middle connector.  
Water Supply Hose  
Checking the water leakage  
After connecting the hose, open the tap to  
check for any water leakage.  
In case of water leakage, close the tap and  
start again from step 1.  
If you skip step1, it may cause water leakage.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Screw Type  
Attach the water supply hose to the tap.  
Push the water supply hose up so that the  
rubber packing within the hose can adhere  
completely to the tap.  
1
Water  
tap  
Rubber Packing  
Water Supply Hose  
Connect the water supply hose to the tap.  
2
3
Connect the water supply hose to the tap and  
then tighten it by screwing it to the right.  
Check water leakage.  
After connecting the hose, open the faucet to  
check for any water leakage.  
Connecting Water Supply Hose to the machine  
Connect the water supply hose to inlet valve  
of the washing machine, and then lock it by  
turning the hose connecting part.  
Hose connector  
Check to see if there is a rubber seal inside  
the connector.  
Rubber seal  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
2-3. CONNECT THE DRAIN HOSE  
For pump model  
·
Connect the drain hose to  
the outlet of the drain pump  
located at the rear of the  
washing machine.  
·
Attach the clip to the drain  
·
Check that the drain hose is  
hung up over the edge of the  
laundry tub.  
hose. And then push it toward  
the body of the washing  
machine as indicated by the  
arrow.  
·Do not use an extension hose.  
Hose  
Guide  
0.9~1.2m  
Drain Hose  
·
NOTE  
:
·
·
Never lay down the drain hose, as water will be discharged.  
Be sure the drain hose is properly routed so it will not kink  
or lift from the sink.  
·
The discharge height should be approximately 0.9~1.2m from  
the floor.  
·
Connect the drain hose adjusting the length of it not to be  
dropped. If drain hose is dropped the drainage could be poor  
because of blockage in the hose.  
For non - pump model  
·
Connect the drain hose to the outlet of the  
drain located at the back side of the  
washing machine.  
·Fix the drain hose with the clip.  
And then push it toward the body as in the  
figure.  
·
Keep it downward while the washing machine  
is working.  
·Ensure the hose is free from kinking.  
·
Do not install the washer where it is directly exposed to sunlight, wind, rain etc.  
Plug the power cord of this washer into a properly installed standard electrical outlet  
that is switched & earthed.  
CAUTION  
·
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. OPERATING INSTRUCTIONS  
3-1. IDENTIFICATION OF PARTS  
WATER SUPPLY HOSE  
SOFTENER DISPENSER  
• Make sure that water does  
• Softener will automatically  
not leak.  
flow into the tub.  
• In case of one valve model  
water supply hose is one.  
DETERGENT DISPENSER  
BLEACH INLET  
POWER SUPPLY  
CORD  
FUNCTION  
SELECTORS  
DRAIN HOSE  
For Pump Model  
• Check out if the drain hose is  
hung up before operating the  
washing machine.  
PULSATOR  
ANTI RAT BASE  
DRAIN HOSE  
For non Pump Model  
ADJUSTABLE LEG  
SPINDLE  
• Keep downward while the  
washing machine is  
working.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-2. BEFORE STARTING TO WASH  
Care Labels  
* Look for a care label on your clothes. This will tell you about the fabric content of your garment  
and how it should be washed.  
Sort clothes into loads that can be washed with the same wash cycle, water temperature and spin speed.  
Sorting  
To get the best results, different fabrics need to be washed in different ways.  
SOIL (Heavy, Normal, Light)  
COLOR (Whites, Lights, Darks)  
LINT (Lint producers, Collectors)  
Separate clothes according to the type and amount of soil.  
Separate white fabrics from colored fabrics.  
Separate lint producers and lint collectors.  
Lint Producers  
Terry cloth, Chenile, Towels, Nappies, Diapers  
Lint Collectors  
Synthetics, Corduroy, Permanent Press, Socks  
Check before Loading  
Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches, pens,  
coins, and keys can damage both your washer and your clothes.  
Mend any torn garments or loose buttons. Tears or holes may become larger during washing.  
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.  
Pretreat any dirt and stains.  
WIRE  
• Make sure the clothes are washable in water.  
• Check the washing instructions.  
• Remove tissue in pockets.  
Pretreatment on stains or heavy soil  
• Pretreat shirt collars and cuffs with a pre-wash product or liquid detergent when placing them in the washer.  
Before washing treat special stains with bar soaps, liquid detergent or a paste of water and granular detergent.  
• Use a pretreat soil and stain remover.  
Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.  
Loading  
WARNING  
Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).  
Fire Hazard  
Load Size  
Never place items in the washer that are  
dampened with gasoline or other  
flammable fluids.  
The water level should just cover the clothes. Adjust the load size accordingly.  
Loosely load clothes no higher than the top row of holes in the washer tub. To  
add items after washer has started, press Start button and submerge additional  
items. Close the lid and press Start button again to restart.  
Light and Large-sized clothing  
Clothes like downs and woollens are light weight, large and float easily.  
No washer can completely remove oil.  
Do not dry anything that has ever had any  
type of oil on it (including cooking oils).  
Doing so can result in death, explosion, or  
fire.  
Use a nylon net and wash them in a small amount of water. If the laundry floats during the wash  
cycle, it may become damaged. Use dissolved detergent to prevent the detergent from clumping.  
Long laundry items  
Use nylon nets for long, delicate items. For laundry with long strings or long length , a net  
will prevent tangling during washing. Fasten zippers, hook, and strings to make sure that  
these items don't snag on other clothes.  
Nylon net is not supplied by LG.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Water  
Amount of Water Level  
WATER - DETERGENT  
• This machine detects the quantity of laundry automatically, then sets the water level and  
EX-LARGE  
LARGE  
proper amount of detergent.  
• When you select a wash program, the water level and amount of detergent (to be used)  
will be shown on the control panel.  
MEDIUM  
SMALL  
• The following table shows the amount of water.  
• When the water level is automatically detected, it may differ depending on the quantity of laundry even  
though the same water level is indicated on the control panel.  
• The amount of a cup in the diagram is about 40g for concentrated detergent.  
Water temperature  
• The machine sets the appropriate temperature automatically according to the wash program .  
You can change the water temperature by pressing the WATER TEMP button.  
• The temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning  
results. We recommend temperatures of:  
- HOT 49~60°C…(120-140˚F)  
- WARM 29~40°C…(85-105˚F)  
- COLD* 18~24°C…(65-75˚F)  
White items, diapers, underclothing and heavily soiled, colorfast items.  
Most items  
Only very bright colors with light soil.  
• When washing in cold water additional steps may be needed:  
- Adjust detergent amount and pre-dissolve detergent in warm water  
- Pretreat spots and stains  
- Soak heavily soiled items  
- Use appropriate bleach  
* Temperature below 18°C…(65˚F) will not activate laundry additives and may cause lint, residue, poor cleaning,  
etc. In addition, detergent manufactures and care labels define cold water as 26~29°C…(80-85˚F).  
If the temperature of the water in the tub is too cold for your hands, the detergent will not activate and clean  
effectively.  
Attention  
If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown  
or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be  
necessary for severe cases.  
Using Detergent  
Detergent  
Follow the detergent package directions. Using too little detergent is a common cause of laundry problems.  
Use more detergent if you have hard water, large loads, greasy or oily soils or lower water temperature.  
Choosing the right detergent  
We recommend the use of domestic detergent, (powder, liquid or concentrated). Soap flakes or granulated  
soap powders should not be used in your washing machine. When washing woolens remember to use  
detergent suitable for washing woolens.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Detergent  
How much detergent  
When you select a wash program the water level and the amount of detergent (to be used) will be shown  
on the control panel. The amount of a cup in the diagram is about 40g for concentrated detergent.  
The correct amount of detergent will vary depending on the amount of soil in your clothes (Jeans and work  
cloches may need more detergent, while bath towels usually need less.).  
For liquid and concentrated detergents, follow the recommendations of the detergent manufacturer.  
Note: To check you are using the correct amount of detergent, lift the lid of your machine about  
half-way through the wash. There should be a thin layer of foam over the surface of the water. Lots  
of foam may look good, but it does not contribute to cleaning your clothes. No foam means not  
enough detergent has been used; soil and lint can settle back on the clothes or the washing  
machine.  
If excess detergent is used, the rinse will not be as clean and efficient. Also, it could cause  
environmental pollution, so use it accordingly.  
Attentión  
Adding the detergent  
Powder Detergent  
Open the detergent dispenser and deposit the appropriate  
amount of detergent.  
Some detergents MUST be fully dissolved before  
adding to your machine to get the best wash results.  
Check the instructions on the detergent packet.  
If you use powdered detergent it is essential that the required amount  
be fully dissolved in very hot water before being added to warm or hot  
water for the actual wash.  
Where you deposit  
the detergent  
Pre-dissolving detergent in warm water when washing in cold water can  
improve its performance.  
Using Liquid Bleach  
Bleach dispenser  
• Check clothing care label for special instructions and separate  
the laundry to be bleached  
(
)
• Dilute liquid chlorine bleach.  
• Measure the recommended amount of liquid bleach carefully  
following instructions on the bottle.  
• Before starting the washer, pour measured amount of bleach  
directly into bleach dispenser. Avoid splashing or overfilling.  
Powdered bleach should be mixed with water before pouring.  
Attention  
Never pour undiluted liquid bleach directly onto clothes or into the wash basket.  
This may cause change of color or damage the laundry.  
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing can reduce  
a toxic gas which may cause death.  
Do not pour powdered bleach into bleach dispenser.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Fabric Softener  
Available Fabric Softener Type  
• Do not use concentrated fabric softener. This may cause some problems in automatic dispensing.  
• For more details refer to the softener products instructions for use.  
Depositing Fabric Softener  
Powder Detergent & Fabric Softener dispenser.  
• Don't use softener with detergent. Use softener in  
last rinse water  
Where you deposit  
the softener  
• When using dispenser, dilute softener (30ml) with  
fresh water (30ml)  
• When filling dispenser, do not splash or overfill. It  
may stain clothes.  
Limit Line  
Depositing  
softener  
• Never pour fabric softener directly on clothes. It  
may stain them  
Fabric Softener Cap  
* If the softener is over filled, it can over flow.  
don’t fill it  
above the  
limit line.  
• If spotting occurs, wet and rub hand dishwashing  
liquid (or mild bar soap) and rewash.  
Note  
Fabric Softener will be inserted automatically during the final rinse and the machine gives on alarm sound.  
When water pressure is low, the softener may have to be inserted manually.  
Scrud(Waxy Build up)  
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener comes into contact with  
detergent. This build-up is not brought about by a fault in the machine.  
If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant smell in your washer.  
If you wish to use fabric softener we recommend  
• Using fabric softener sparingly.  
• When filling the dispenser, do not splash or overfill.  
• Clean dispenser as soon as the cycle is finished.  
• Clean your machine regularly. (refer to page 25)  
• Cold water washing increases the chance of this build-up occurring. We recommend a regular warm or hot wash e.g. every 5th  
wash should be at least a warm one.  
• Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a build-up.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Special Guide for Stain Removal  
WARNING  
Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or products  
containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.  
To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:  
• Read and comply with all instructions on stain removal products.  
• Keep stain removal products in their original labeled containers and out of children’s reach.  
• Thoroughly wash any utensil used.  
• Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.  
• Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning  
solvents or other flammable or explosive substances because they give off vapors that could ignite or explode.  
• Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or  
sparks.  
For successful stain removal:  
• Remove stains promptly.  
• Determine the kind of stain, then follow the recommended treatment in the stain  
removal chart below.  
To pretreat stains, use a prewash product, liquid detergent, or a paste made from  
granular detergent and water.  
• Use cold water on unknown stains because hot water can set stains.  
• Check care label instructions for treatments to avoid on specific fabrics.  
Follow fabric care label  
instructions  
• Check for colorfastness by testing stain remover on an inside seam.  
• Rinse and wash items after stain removal.  
Stain Removal  
STAIN  
TREATMENT  
Adhesive tape, chewing gum,  
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or  
rubber cement  
nonflammable dry cleaning fluid.  
Baby formula, dairy products, egg  
Use product containing enzymes to pretreat or soak stains.  
Pretreat stain. Wash using cold water and bleach safe for fabric.  
Beverages (coffee, tea, soda,  
juice, alcoholic beverages)  
Rinse with cold water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using  
Blood  
bleach safe for fabric.  
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is  
absorbed. Replace paper towels frequently. Treat remaining stain with prewash stain remover or  
nonflammable dry cleaning fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.  
Candle wax, crayon  
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.  
Pretreat with prewash stain remover or rub with bar soap.  
Chocolate  
Collar or cuff soil, cosmetics  
Dye transfer on white fabric  
Grass  
Use packaged color remover. Wash using bleach safe for fabric.  
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.  
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply  
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly.  
Wash using hottest water safe for fabric.  
Grease, oil, tar (butter, fats, salad  
dressing, cooking oils, car grease,  
motor oils)  
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover,  
Ink  
denatured alcohol or nonflammable dry cleaning fluid.  
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water before washing. Badly  
mildewed fabrics may be permanently damaged.  
Mildew, scorch  
Brush off dry mud. Pretreat or soak with product containing enzymes.  
Pretreat with prewash stain remover. Wash using bleach safe for fabric.  
Mud  
Mustard, tomato  
Nail polish  
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of  
stain. Repeat, replacing paper towels frequently. Do not use on acetate fabrics.  
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,  
OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing.  
Paint, varnish  
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate detergent and  
Rust, brown or yellow  
discoloration  
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.  
LIQUID : Pretreat with a paste of granular detergent and water. PASTE : Scrape residue from fabric. Pretreat  
with prewash stain remover or nonflammable dry cleaning fluid. Rub detergent into dampened area, Wash  
using bleach safe for fabric.  
Shoe polish  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-3. FUNCTION OF EACH BUTTON  
Changing various functions is possible only in PAUSE state.  
Selection button does not work when the washer is in operation (Except for water level, water temp, water power button).  
How to use delayed  
washing  
Detergent deposit  
display  
Upon loading laundry, it  
displays the correct amount of  
detergent to be added  
Wash Process display  
Use this function for delayed  
Indicates the current washing  
washing.  
status.  
Use it to set the delay time.  
Next step is lit, current step blinks  
By pressing the button, it cycles  
[345...111214→  
16...46483] hours.  
(Up to 48 hours can be  
delayed).  
according to the amount of  
laundry (based on  
concentrated detergent).  
and finished step is turned off.  
NOTE  
The display panel uses the  
following abbreviation:  
M(minutes), T(Times) and  
M(minutes).  
To cancel delay time, turn the  
power switch off.  
How to select temp.  
Use it to select hot or cold  
water (When hot water only is  
selected, hot water is supplied  
for washing and cold water are  
supplied for rinsing).  
WARM  
WATER - DETERGENT  
EX-LARGE  
LARGE  
S
N
G
TRONG  
ORMAL  
ENTLE  
D
HOT  
COLD  
MEDIUM  
SMALL  
LEVEL  
In WOOL, HOME DRY  
program, cold water is selected  
automatically (Hot water may  
damage the fabric).  
DELAY  
START  
WATER  
TEMP.  
WATER  
LEVEL  
WASH  
POWER  
How to adjust the water level  
Wash power  
By pressing the button, it cycles  
Use it to adjust the strength of  
water current.  
[LARGELARGEEX-LARGEEX-LARGE  
SMALLSMALLMEDIUMMEDIUM  
MEDIUMLARGELARGE]  
By pressing the button, it  
cycles  
[
].  
S
G
N
At FUZZY and JEAN program, water level is selected automatically  
Strength of the water current can  
be adjusted at any program.  
At the beginning, it starts with  
MED  
based on the amount of laundry.  
Water level is set to MEDIUM for SPEEDY program, LARGE for  
WOOL and DELICATE program, EX-LARGE for BLANKET program.  
Water level can be adjusted even when the washer  
S
(
).  
is in operation.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For manual wash, rinse  
and spin  
Displaying abnormal operation  
In case of abnormal operation, the following indications are displayed.  
Abnormal water supply : INLET Er. lamp blinks.  
Abnormal drainage : DRAIN Er. lamp blinks.  
Wash :  
Use it to change washing time.  
By pressing the button[ 15min →  
18min21min25min40min→  
60min90minOFF3min6min9min  
12min15min]SOAKING is used to  
remove old or hardened dirt more  
effectively.  
Abnormal spin : SPIN Er. lamp blinks.  
Abnormal water level sensing :  
displayed.  
Abnormal lid open : DOOR Er. lamp blinks.  
Soaking time is about 40,60,90 minutes  
(You cannot choose in WOOL , HOME  
DRY, DELICATE program.).  
Abnormal over flooding sensing :  
displayed.  
Rinse :  
Use it to change the frequency of rinses.  
By pressing the button,  
[ rinse 1 rinse 2 rinse 3 rinse 4 →  
rinse 5 off rinse 1] or  
[ Spray rinse+Deep 1 Deep 1 Spray  
rinse+Deep 2 Deep 2off Spray  
rinse+Deep 1] are repeated.  
When you select rinse only, the  
operation starts with water supply.  
AUTO OFF  
NOTE  
SOAK WASH  
SHOWER RINCE  
(SPRAY)  
SPIN  
3
FUZZY  
HOME DRY  
(NORMAL)  
(FAVOURITE)  
INLET Er.  
When rinsing or spinning only, Fuzzy is set to  
[LARGE] and ECONOMY is set to [MEDIUM]  
and BLANKET is set to [EX-LARGE]  
BLANKET  
ECONOMY  
WOOL  
JEAN  
(DELICATE)  
DRAIN Er.  
DOOR Er.  
SPIN Er.  
3
(SPEEDY)  
M
T
M
automatically. Adjust the water level as needed.  
START  
PAUSE  
Spin :  
Use it to change the spinning time.  
By pressing the button,  
PRO -  
WASH RINSE  
SPIN  
GRAM  
[ 6min 8min OFF 1min  
2min 4min 6min]  
How to select a  
Start and temporary  
Child lock function  
washing program  
pause  
Use it to select washing  
Use to lock or unlock the  
control buttons to prevent  
all the setting being change  
by a child.  
For locking, push both  
buttons simultaneously and  
for unlocking, push them  
one more in washing  
process.  
Use it to start or  
pause temporarily.  
programs.  
Pressing the button  
repeats start and  
By pressing the button, it  
cycles [ FUZZY(NORMAL)→  
BLANKET(DELICATE) →  
ECONOMY(SPEEDY) →  
JEAN WOOL →  
temporary pause.  
After 10 minutes in a  
temporary pause  
state, the power will  
automatically turn  
off.  
HOME DRY(FAVOURITE)→  
FUZZY(NORMAL) ]  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-4. WASHING PROGRAMS  
AUTO OFF  
Washing  
Programs  
Add  
Add  
PRO -  
GRAM  
the laundry  
the deterg  
1
1
2
Fuzzy Washing (Normal Wash)  
Used for normal loads, this mode  
·Add the appropriate  
detergent as indicat  
water level next to W  
DETERGENT.  
automatically selects the most appropriate  
conditions and completes the sequence in  
one operation. The built-in sensor detects the  
size of the load and the ideal wash power and  
wash, rinse and spin times are set accordingly  
Or follow the deterg  
manufacturer’s inst  
Blanket Wash  
3
5
Blankets of different size can be easily  
2
washed.  
·Select the  
BLANCKET  
program on the  
Control panel.  
Delicate Wash  
3
3
3
2
5
1
1
1
1
Use this program for washing delicate  
laundry such as lingerie, blouses etc.  
·Select the  
DELICATE  
program on the  
Control panel.  
Economy Wash (Speedy Wash)  
2
Use this mode when washing lightly soiled  
clothes for a short time. The weight should  
be under 2.0kg.  
·Select the  
ECONOMY  
(SPEEDY) program  
on the Control panel.  
Jean Wash  
2
Use jeans program when washing heavy,  
thick, and extremely dirty laundry such as  
jeans and work outfits.  
·Select the JEAN  
program on the  
Control panel.  
Wool Wash  
3
3
Use this program for washing delicate fabrics  
such as lingerie and woolens.  
2
·Use neutral deterg  
appropriate for the  
·When washing wo  
a mild detergent  
recommended for  
wool.  
(wash only “water washable” clothes)  
Before washing your woolens check the care  
label for the washing instructions.(wash only  
water washable clothes)  
·Select the  
WOOL program  
on the Control  
panel.  
Homedry Wash  
Use this program for clothes that have  
2
1
[HOME WASH and DRY] or [WATER  
WASH and DRY] tags. For homedry,  
amount of laundry must be less than 1.2kg  
at a time.  
·Select the  
HOMEDRY  
program on the  
Control panel.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
START  
PAUSE  
Close the lid  
Finish  
Caution & Note  
t
·If water is already in the tub, or putting wet laundry  
into the tub before starting will increase the water  
level.  
3
5
6
antity of  
by the  
TER-  
·The pulsator rotates for 8 seconds to  
detect the laundry load.  
·Water will be supplied for 2  
minutes after the start of the  
wash to supplement the  
water the laundry has  
absorbed.  
·When the wash program  
ends, the buzzer will ring for  
10 seconds before the  
Power goes off  
·With lightweight bulky loads, water level can be set  
low.  
·Then the water level and the amount of  
detergent to be used will be shown and  
water will be supplied.  
·Changes to water temperature (hot/cold) and wash  
level are possible during operation.  
automatically.  
ons  
·Before starting to wash, make sure that the laundry is  
washable.  
6
7
4
100% chemical  
Weight : the weight of  
sheet is under 5.0kg  
fiber with the  
hand-wash tag  
Possible  
Laundry  
Blanket Stuffing : Weight  
about 2kg  
100% Polyester  
with the  
(total weight of blanket 3.5kg)  
Size : under approx.  
hand-wash tag  
2m(width) ×2.5m(breadth)  
Impossible • electrical  
Laundry  
blankets  
• carpets  
·Use a nylon net for washing cashmere blankets to prevent  
them floating out of the tub.  
·Water may splash out when washing light laundry , such as  
a cashmere blanket or bed sheet with water set at high level.  
6
7
4
4
4
7
7
6
6
6
·When setting the water level manually, do not set to MEDIUM  
to prevent damage to laundry.  
7
4
·Washing with hot water may damage the laundry (Water is set  
to cold automatically). Ensure that the load is under 2kg  
·In order to avoid damage to laundry,  
ndry.  
s use  
the spin cycle may appear slow.  
This also avoids wrinkles and clothing may still contain some  
water. This is normal.  
hing  
·Soak Wash cannot be selected for the Wool Wash program.  
4
6
7
·The water level and the amount of  
detergent to be used will be shown  
and water will be supplied.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-5. OTHERS FUNCTIONS  
1) Soak Wash  
Use this mode for washing excessively dirty laundry by soaking in water for some time to remove proteins and  
fats  
. SOAKmode can be used with all washing programs simultaneously except for WOOL and HOME DRY  
program.  
1
Press the AUTO OFF (Power) button to turn power on.  
AUTO OFF  
2
3
Press the PROGRAM button to select the washing program.  
The SOAK will not work in WOOL and HOME DRY cleaning  
PRO -  
GRAM  
Program.  
Press the WASH button, to select SOAK program.  
SOAK  
WASH  
Keep pressing the WASH button until  
the light turns onSoakandWash’  
simultaneously as next image.  
WASH  
SOAK program only works when  
socking time is 40, 60 or 90 minutes.  
4
5
Add the detergent.  
The appropriate quantity of detergent marked next to the  
water level of WATER-DETERGENT.  
Add the laundry and press the START/PAUSE button.  
The water level and the amount of detergent to be used will  
be shown and water will be supplied.  
Water will be supplied for 2 minutes after the start of the wash  
to supplement the absorbed water by the laundry.  
6
Close the lid.  
Finish  
When the wash program ends, the buzzer will ring for  
10seconds before the Power goes off automatically.  
Note  
• Order of Soak-Wash timing  
Soak-Wash  
Lamp  
min  
min  
min  
min  
min  
min  
min  
min  
min  
min  
min  
Off  
• Select soaking time 40minutes, 60minutes, or 90minutes (including washing time) by pressing the Wash  
button repeatedly.  
• If necessary, select the times of Rinse and the time for Spinning by pressing the Rinse or Spin buttons till  
you reach the desired times.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2) Delay Start (Reservation) Wash  
Delay start (Reservation) Wash is used to delay the finishing time of the operation. The hours to be  
delayed can be set by the user accordingly.  
The time on the display is the finishing time , not the start time.  
1
2
3
Press the AUTO OFF (Power) button to turn power on.  
AUTO OFF  
Press the PROGRAM button to select the washing program.  
• Select the program for laundry on the Control panel.  
PRO -  
This method will not work in Wool Program.  
GRAM  
Press the DELAY START (RESERVATION) button.  
• The light will ‘ DELAY’ turn on and ‘TIME LEFT’  
will be marked.  
• Press the button repeatedly to set the desired finishing  
time. For example, To finish washing in 9 hours from  
now, by make the number 9:00 pressing the DELAY  
START (RESERVATION ) button repeatedly.  
DELAY  
START  
SOAK  
WASH SPRAY RINSE  
SPIN  
SOAK  
WASH SPRAY RINSE  
SPIN  
DELAY  
INLET Er.  
DRAIN Er.  
DOOR Er.  
SPIN Er.  
DELAY  
INLET Er.  
DRAIN Er.  
DOOR Er.  
SPIN Er.  
(RES.=DELAY)  
TIME  
LEFT  
TIME  
LEFT  
• The appropriate quantity of detergent marked next to the water  
level of WATER-DETERGENT.  
Add the detergent.  
4
5
• When the lid is open the machine will not operate, and an alarm  
signal will remind you to close the lid.  
Add the laundry and press the START/PAUSE button.  
• When you press the START/PAUSE button the light will blink  
and the time will be shown.  
• Water will be supplied for 2 minutes after the start of the  
wash to supplement the water the laundry has absorbed.  
6
Close the lid.  
The washing will be finished according to the delayed time.  
Finish  
Note  
• Finishing time can be delayed from 3~48 hours. Delaying from3~12 hours can be done in 1 hour time intervals  
and from 12~48 hours in 2 hour time intervals.  
• If the lid is open, the machine will not work, and an alarm signal will alarm to remind you to close the lid.  
• To select washing time, rinsing times, spinning time, water level, hot/cold or wash power manually, press the  
DELAY START (RESERVATION) button and select the desired option. Then press the START/PAUSE button.  
• When the laundry cannot be taken out immediately after the wash program ends, it is better to omit the spinning  
program . (The laundry will be wrinkled if left for a long time after spinning.)  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3) Option Washing  
When you only need the Wash, Wash/Rinse or Rinse cycles, these can be set manually.  
Press the AUTO OFF (Power) button to turn power on.  
1
2
AUTO OFF  
Only Wash  
Only Wash,Rinse  
Press the WASH button to select the  
Press the WASH button to select the  
desired timing.  
desired timing.  
WASH  
WASH  
Press the RINSE button to select the  
desired times of rinse.  
RINSE  
You can use this option for preventing  
wrinkles of laundry  
Press the WATER LEVEL button, to control the water level according to  
the amount of laundry. If you do not choose anything, it is set the middle  
water level automatically.  
3
Add the laundry into the washing tub.  
4
5
Press the START/PAUSE button.  
6
Add the detergent and close the lid.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3) Option Washing  
1
2
Press the AUTO OFF (Power) button to turn power on.  
AUTO OFF  
Only Rinse,Spin  
Only Spin/Only drain  
Only Rinse  
Press the RINSE button  
to select the desired  
times of rinse.  
Press the RINSE button to  
select the desired times of  
rinse.  
Press the SPIN button to  
select the desired times  
of rinse.  
RINSE  
RINSE  
PRO -  
GRAM  
Press the SPIN button to  
select the desired times of  
rinse.  
When you want to only  
drain, wait until the water  
in the washing tub drains  
completely.  
SPIN  
3
Press the WATER LEVEL button to control the water  
level according to the amount of laundry.  
4
5
Add the laundry into the washing tub.  
Press the START/PAUSE button.  
6
Add the detergent and close the lid.  
Note  
When a Wash, Wash/Rinse or Rinse only option is selected, after the wash is completed the water will not  
be drained off. If you wish to drain the water, press SPIN button and wait until the water in the tub has drained  
completely. Then press the START/PAUSE button.  
If you do not specify the water level, then Medium will be automatically selected.  
If only Rinse is selected, the process will start from Water Supply.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4) Child Lock Function  
If you want to lock all the keys to prevent all the setting from being changed by a child, you can use the child lock  
option.  
How to Lock  
1
Press the AUTO OFF(Power) button.  
AUTO OFF  
Turn Power on.  
Press the START/PAUSE button to start washing.  
2
3
After all washing conditions are set according to the manual.  
Press both the WASH button and the RINSE button simultaneously.  
During the wash program, all the buttons are locked until  
SHOWER  
(SPRAY)  
washing is completed or it is child- lock  
function is deactivated manually.  
DELAY  
How to Unlock  
If you want to unlock during wash, press both the WASH and the RINSE button simultaneously again.  
Note  
” & the remaining time are alternatively shown on the display while they are locked.  
Mute Option  
If you want to use the washing machine without alarm signal sounds, press both the WASH and  
SPIN buttons simultaneously.  
To make buzzer work, press both the WASH and SPIN buttons simultaneously one more time.  
Seeing Remaining Time  
To see the remaining time for each process, press one of the WASH, RINSE and SPIN buttons.  
The remaining time for each process will appear for about 1 second.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3-6. CARE AND MAINTENANCE  
When there is a fear of freezing  
• Close the water taps and remove the Water Supply Hose.  
• Remove the water which remains in the water supply.  
• Lower the drain hose and drain the water in the bowl and the drain hose by spinning.  
If frozen  
• Remove the water supply hose, and immerse it in hot water at approx.. 40˚C.  
• Pour approx.. 2 liters of hot water at approx.. 40˚C, into the bowl and let it stand for 10 minutes.  
• Connect the water supply hose to the water tap and confirm that the washing machine performs  
the supply and drainage of water.  
Wash Inner-tub  
Leave the lid open after washing to allow moisture to evaporate. If you want to clean  
the inner-tub use a clean soft cloth dampened with liquid detergent, then rinse. (Do  
not use harsh or gritty cleaners.)  
Inlet Hoses  
Exterior  
Hoses connecting washer to faucet should be replaced every 5 years.  
Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with  
sharp objects.  
Long Vacations Be sure water supply is shut off at faucets. Drain all water from hoses if weather will  
be below freezing.  
Cleaning the Inside of your Washer  
If you use fabric softener or do regular cold water washing, it is very important that you occasionally  
clean the inside of your washer.  
• Fill your washer with hot water.  
• Add about two cups of a powdered detergent that contains phosphate.  
• Let it operate for several minutes.  
• Stop the washer, open the lid and leave it to soak overnight.  
• After soaking, drain the washer and run it through a normal cycle.  
We do not recommend that you wash clothes during this procedure.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. SERVICE INFORMATION  
4-1. SCHEMETIC DIAGRAM  
1) WF-T10(~3)0(~2,6)1(~5)TP(H,E,F)(S,3) / WF-T802/T852(A)  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2) WF-T(F/C)1091~3, 1191~3T(C/H/P) / WF-T(F/C)1022,1122,1001T(C/H/P)  
WF-T1268TH, 2409KTb, 2602kTa, T1491TP, WF-T1491TP, T11292TP, T1292TP,T1291TP,  
LA-1499ST, WF-T1081TP, T1592TP, T1593TP, T1241TP, T1133TH  
WF-G15KTB, G13KTC, B15KTB, B13KTC / WF-T1400TH, T1022TPX  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-2. WIRING DIAGRAM  
1) WF-T10(~3)0(~2,6)1(~5)TP(H,E,F)(S,3) / WF-T802/T852(A)/T853A  
2) WF-T(F/C)1091~3, 1191~3T(C/H/P) / WF-T(F/C)1022,1122,1001T(C/H/P)  
WF-T1268TH, 2409KTb, 2602kTa, T1491TP, T1081TP, WF-T1491TP, T11292TP,  
T1292TP,T1291TP, LA1499ST, T1592TP, T1593TP, T1241TP, T1133TH  
WF-G15KTB, G13KTC, B15KTB, B13KTC / WF-T1400TH, T1022TPX  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-3. PROGRAM TIME CHART  
1) WF-T10(~3)0(~2,6)1(~5) Series Program chart  
Wash  
1st Deep Rinse  
2nd Deep Rinse  
Spin  
Fuzzy  
Economy  
Blanket  
Jean  
Ex-large  
ExL-L  
Large  
L-M  
Medium  
M-S  
7
15  
15  
15  
12  
12  
9
4
4
4
3
3
3
3
130" 90" 165"  
130" 90" 140"  
100" 90" 140"  
100" 90" 120"  
100" 90" 120"  
55" 90" 100"  
55" 90" 100"  
7
6
6
5
5
4
3
3
3
3
3
3
3
3
4
4
4
3
3
3
3
130" 90" 165"  
130" 90" 140"  
100" 90" 140"  
100" 90" 120"  
100" 90" 120"  
55" 90" 100"  
55" 90" 100"  
7
6
6
5
5
4
3
3
3
3
3
3
3
3
4
4
4
3
3
3
3
130"  
130"  
100"  
100"  
100"  
55"  
8
8
6
6
6
4
4
165" 10"  
140" 10"  
140" 10"  
120" 10"  
120" 10"  
100" 10"  
100" 10"  
6
6
5
5
4
3
Small  
9
55"  
Ex-large  
ExL-L  
Large  
L-M  
Medium  
M-S  
7
6
6
5
5
4
3
9
9
9
9
9
9
9
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
4
4
4
3
3
3
3
130" 90" 165"  
130" 90" 140"  
100" 90" 140"  
100" 90" 120"  
100" 90" 120"  
55" 90" 100"  
55" 90" 100"  
7
6
6
5
5
4
3
3
3
3
3
3
3
3
4
4
4
3
3
3
3
130"  
130"  
100"  
100"  
100"  
55"  
4
4
4
4
4
4
4
165" 10"  
140" 10"  
140" 10"  
120" 10"  
120" 10"  
100" 10"  
100" 10"  
Default  
Default  
Small  
55"  
Ex-large  
ExL-L  
Large  
L-M  
Medium  
M-S  
7
6
6
5
5
4
3
18  
18  
18  
18  
18  
18  
18  
4
4
4
3
3
3
3
130" 90" 165"  
130" 90" 140"  
100" 90" 140"  
100" 90" 120"  
100" 90" 120"  
55" 90" 100"  
55" 90" 100"  
7
6
6
5
5
4
3
3
3
3
3
3
3
3
4
4
4
3
3
3
3
130" 90" 165"  
130" 90" 140"  
100" 90" 140"  
100" 90" 120"  
100" 90" 120"  
55" 90" 100"  
55" 90" 100"  
7
6
6
5
5
4
3
3
3
3
3
3
3
3
4
4
4
3
3
3
3
130"  
130"  
100"  
100"  
100"  
55"  
8
8
8
8
8
8
8
165" 10"  
140" 10"  
140" 10"  
120" 10"  
120" 10"  
100" 10"  
100" 10"  
Small  
55"  
Ex-large  
ExL-L  
Large  
L-M  
Medium  
M-S  
7
6
6
5
5
4
3
15  
15  
15  
15  
15  
15  
15  
4
4
4
3
3
3
3
130" 90" 165"  
130" 90" 140"  
100" 90" 140"  
100" 90" 120"  
100" 90" 120"  
55" 90" 100"  
55" 90" 100"  
7
6
6
5
5
4
3
3
3
3
3
3
3
3
4
4
4
3
3
3
3
130" 90" 165"  
130" 90" 140"  
100" 90" 140"  
100" 90" 120"  
100" 90" 120"  
55" 90" 100"  
55" 90" 100"  
7
6
6
5
5
4
3
3
3
3
3
3
3
3
4
4
4
3
3
3
3
130"  
130"  
100"  
100"  
100"  
55"  
8
8
6
6
6
4
4
165" 10"  
140" 10"  
140" 10"  
120" 10"  
120" 10"  
100" 10"  
100" 10"  
Small  
55"  
Wool  
Ex-large  
ExL-L  
Large  
L-M  
Medium  
M-S  
7
6
6
5
5
4
3
3
3
3
3
3
3
3
4
4
4
3
3
3
3
130"  
130"  
100"  
100"  
100"  
55"  
-
-
-
-
-
-
-
100"  
100"  
100"  
100"  
100"  
100"  
100"  
7
6
6
5
5
4
3
3
3
3
3
3
3
3
4
4
4
3
3
3
3
130"  
130"  
100"  
100"  
100"  
55"  
-
-
-
-
-
-
-
100"  
100"  
100"  
100"  
100"  
100"  
100"  
7
6
6
5
5
4
3
3
3
3
3
3
3
3
4
4
4
3
3
3
3
130"  
130"  
100"  
100"  
100"  
55"  
-
-
-
-
-
-
-
100" 10"  
100" 10"  
100" 10"  
100" 10"  
100" 10"  
100" 10"  
100" 10"  
Default  
Small  
55"  
55"  
55"  
Home Dry Ex-large  
7
6
6
5
5
4
3
6
6
6
6
6
6
6
4
4
4
3
3
3
3
130"  
130"  
100"  
100"  
100"  
55"  
-
-
-
-
-
-
-
100"  
100"  
100"  
100"  
100"  
100"  
100"  
7
6
6
5
5
4
3
3
3
3
3
3
3
3
4
4
4
3
3
3
3
130"  
130"  
100"  
100"  
100"  
55"  
-
-
-
-
-
-
-
100"  
100"  
100"  
100"  
100"  
100"  
100"  
7
6
6
5
5
4
3
3
3
3
3
3
3
3
4
4
4
3
3
3
3
130"  
130"  
100"  
100"  
100"  
55"  
-
-
-
-
-
-
-
100" 10"  
100" 10"  
100" 10"  
100" 10"  
100" 10"  
100" 10"  
100" 10"  
ExL-L  
Large  
L-M  
Medium  
M-S  
Default  
Small  
55"  
55"  
55"  
WASH OPTION  
Wash Time  
Rinse Times  
Spin Time  
3,6,9,12,15,18,21,25min  
1,2,3,4,5Times  
1,2,4,6,8min  
* No Power Spin : Spin by remained power  
* Time Unit is minute in the chart (34" : 34 second)  
* Total time for full process can be changeable depending on the water pressure.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2) WF-T852(A) Program chart  
P o w e r O f f  
S p i n P o o w N e r  
S p i n  
i g H h S p e e d  
I n t e r m i t t e n t S p i n  
D r a i n  
R i n s i n g  
W a t e r S u p p l y  
S p i n P o o w N e r  
S p i n  
i g H h S p e e d  
I n t e r m i t t e n t S p i n  
D r a i n  
R i n s i n g  
W a t e r S u p p l y  
S p i n P o o w N e r  
S p i n  
i g H h S p e e d  
n I t e r m i t t e n t S p i n  
D r a i n  
o t R a t e S h o w e r  
S p i n P o o w N e r  
n I t e r m i t t e n t S p i n  
D r a i n  
W a s h i n g  
W a t e r S u p p l y  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3) WF-T(F/C)1091~3, 1191~3T(C/H/P) / WF-T(F/C)1022,1122,1001T(C/H/P)  
WF-T1268TH, 2409KTb, 2602kTa, T1491TP, T1081TP, LA-1499ST  
WF-T1491TP, T11292TP, T1292TP, T1291TP, T853A, T1592TP, T1593TP, T1241TP, T1133TH  
WF-G15KTB, G13KTC, B15KTB, B13KTC / WF-T1400TH, T1022TPX  
P o w e r O f f  
S p i n  
S p i n  
o N P o w e r  
H i g h S p e e d  
I n t e r m i t t e n t S p i n  
D r a i n  
R i n s i n g  
W a t e r S u p l y  
o N P o w e r  
S p i n  
S p i n  
H i g h S p e e d  
I n t e r m i t t e n t S p i n  
D r a i n  
R i n s i n g  
W a t e r S u p l y  
o N P o w e r  
S p i n  
S p i n  
H i g h S p e e d  
n I t e r m i t t e n t S p i n  
D r a i n  
S h o w e o r t R a t e  
S p i n  
o N P o w e r  
n I t e r m i t t e n t S p i n  
D r a i n  
W a s h i n g  
a t e W r S u p l y  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-4. ADJUSTMENT  
1) BRAKE LEVER ADJUSTMENT  
• Shown as in the figure, untighten the adjustment  
screw to keep clearance less than 1.9±0.1mm  
between the tip and the brake lever.  
Brake lever  
And turn on the lock nut then paint it red.  
Keep the clearance  
Lock net  
1.9 0.1mm between  
the tip of the adjustment  
screw and brake lever.  
CAUTION.  
CAUTION  
Adjustment  
screw  
Clutch lever  
• Painting part is adjusted in factory, it does not  
need adjusting.  
Brake lever bar  
• Adjust the screw properly if the brake doesn't  
work during spin.  
2) KEEPING CLEARANCE  
P.V Link  
• Keep the clearance about 2.0~3.5mm between  
brake lever and P.V link as shown in the figure.  
Brake lever  
CAUTION  
• Clutch pulley must be turning to one side P.V  
Motor Pulley  
Clutch lever  
Link is pulling the brake Lever.  
• Clutch pulley must be turning to the left and the  
right when P.V Linke does not pull the brake  
Lever.  
3) V-BELT ADJUSTMENT  
1
2
2
• Adjust the motor pulley by pushing the motor like  
Motor Pulley  
arrow , to make V-belt tension parallel when  
pushed at the point of arrow  
.
CAUTION  
• When the V-belt is not properly adjusted, the  
motor will not be running or the belt will be  
slipping.  
Clutch Pulley  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-5. DISASSEMBLY INSTRUCTION  
Be sure to unplug the power to repair and replace  
electric parts.  
CAUTION FOR ELECTROSTATICS  
Be sure to make earth connection for trouble  
diagnosis and parts replacement. If impossible,  
touch earth wire on the body to remove electric  
deviation between the body and product before  
work.  
Screw cap  
1) Disassembly of Front Panel & PCB  
Assembly  
Remove two screw caps using a sharp tool and two  
special screws.  
Special  
screw  
Push the front panel to the left side then pull it out  
Disconnect the leads from the controller  
Panel  
Remove 4 screw from the front panel  
Remove the PCB Assembly.  
Leads  
PCB  
Assembly  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2) Disassembly of Back Panel, Power  
Cord, Inlet Valve & BP Sensor  
Remove two back panel fixing screws in the back  
side.  
Back  
panel  
Disassemble the back panel.  
Disconnect two connectors and disassemble the  
power cord.  
Inlet valve ass'y  
Remove a valve fixing screw & disconnect the  
leads form the inlet valve.  
Remove the inlet valve.  
Disconnect the leads & the pressure tube from the  
BP sensor.  
Fuse holder  
B.P Sensor  
Remove the BP sensor.  
Fuse  
Fuse is located in the Fuse holder.  
For fuse replacement use the following rated fuse  
* Rating of fuse  
Power  
Cord  
- 250V 6A fusing type for 220-240V product  
- 125V 12A fusing type for 100-127V product  
Q-spring  
3) Disassembly of Lid Assembly, Top  
Cover, Tub Cover, Pulsator & Inner Tub  
Remove Q-spring & two hinge pins then  
disassemble the lid assembly  
Remove two top cover fixing screws in the rear  
then disassemble the top cover.  
Remove tub cover fixing screws then disassemble  
the tub cover.  
Remove the pulsator fixing screw then disassemble  
the pulsator.  
Remove the hub fixing nut by a special tool.  
Disassemble the inner tub.  
Hinge Pin  
Hinge Pin  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
tub cover  
inner  
tub  
pulsator  
Hub fixing nut  
4) Disassembly of Back Cover, Drain  
Pump, Clutch(Transmission) & Motor  
Remove back cover fixing screws then  
disassemble the back cover.  
Disconnect the leads and the drain hose-p from the  
drain pump.  
Remove the pump fixing screws then disassemble  
the drain pump.  
Fall down the washer for clutch & motor removal.  
Remove the belt.  
Disassemble the clutch.  
Remove two motor fixing screws then disassemble  
the motor.  
Drain hose-p  
Leads  
Pump  
fixing  
screw  
5) Replacement of Damper asm  
Separate top cover from washing machine.  
As in the fig, lift snubber bar and take it out of out  
C
case with out tub.  
B
Damper assembly shall not be disassembled.  
Replace damper as assembly.  
D
For assembly, keep the following.(Location & color)  
A
Location  
P/No.  
A051  
A052  
PIVOT(Color)  
MIDDLE BLUE  
WHITE  
,
,
A
C
B
D
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-6. TEST RUNNING WITHOUT WATER  
1) METHOD TO USE QC TEST MODE  
To use check program (QC test mode), power ON with water temperature and water level.  
Key pressed in non-load empty water.  
Check method  
Normal condition  
No. Check points  
Start/Pause  
Errorr  
-
Remedy  
KEY PUSH Press  
Load  
Display  
1
LED  
and  
Begining point  
Sensor  
Buzz once  
LED on all  
Check pressure  
No.200 displayed  
S/W assembly.  
Pressure  
LEVEL  
sensor  
No.264~270 is  
Check connector.  
(check level)  
displayed.  
Frequency  
Replace  
controller's IC3.  
display  
2
Motor  
Press once  
Pulsator  
rotates to  
left four  
No.70~125 is  
Check in unload  
displayed.  
condition.  
Check connector.  
times and  
right four  
times.  
Check driving  
part (Motor,  
Clutch, V-belt,  
Capacitor).  
50Hz  
60Hz  
3
4
Cold water valve  
Press twice  
Cold  
valve  
-
starts.  
Hot water valve Press three time Hot water  
Top filter of supply  
valve is clogged  
with dregs.  
valve  
starts  
Check connector.  
Check if TR3(hot)  
TR4(cool) and  
TR5(shower) are  
ON in load driving  
Part of connector  
asm.  
5
Shower valve  
Press four times  
Shower  
valve  
starts  
-
6 Check drain valve Press five times Drain valve  
Check door.  
ON(Turbo  
Drum).  
Door  
error  
Check drain hose  
and drain motor  
.
(Buzz  
Check connector.  
continued) Check TR6 in  
controller asm.  
7
8
Check the drain Press Six times Drain Pump  
Check drain pump  
Check TR8 in  
Pump.  
ON  
Drain Valve  
ON  
controller asm.  
Check connector.  
Check the AUTO Press Seven times Power off  
LED off  
OFF switch.  
within 1  
sec.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-7. TROUBLE SHOOTING AGAINST COMMON WASHING PROBLEMS  
Many washing problems involve poor soil & stain removal, residues of lint and scum,  
and fabric damage. For satisfactory washing results, follow these instructions.  
WASH PROBLEM  
Problems  
Solutions & Preventive Measures  
Possible Causes  
• Not enough detergent  
• Wash water temperature  
too low.  
Poor soil  
removal  
• Use correct amount of detergent for load size, amount of soil  
and water hardness.  
• Use warm or hot water for normal soil.  
Different water temperature may be required according to soil  
type. (refer to page 12)  
• Overloading the washer  
• Incorrect wash cycle  
• Incorrect sorting  
• Reduce load size.  
• Do not pretreat stain  
• Wash with Jean or Soak(Turbo) & Jean wash cycle for heavy  
soiled laundry.  
• Separate heavily soiled items from lightly soiled ones.  
• Pretreat stain and heavy soil according to directions shown on  
page 11.  
• Undiluted fabric softener  
dispensed directly onto  
fabric  
Blue Stains  
• Rub the stain with bar soap. Wash.  
• Do not overfill fabric softener dispenser and do not pour liquid  
fabric softener directly onto fabric.  
See page 14 for more instructions.  
• A buildup caused by the  
interaction of fabric  
Black or gray  
marks on  
clothes  
• Keep the recommendations against Scrud(waxy buildup). (refer  
to scrud page14.)  
softener and detergent can  
flake off and mark clothes  
• Not enough detergent  
• Use correct amount of detergent for load size, amount of soil  
and water hardness.  
• Iron or manganese in  
water supply, water pipes,  
or water heater  
Yellow or  
brown rust  
stains  
To restore discolored load of whites, use rust remover safe for  
fabric.  
• Install nonprecipitating water softener or an iron filter in your  
water supply system for an ongoing problem.  
• Before washing, run water for a few minutes to clear lines.  
• Wash lint givers eg towels, flannelette sheets, separately from lint  
collectors eg synthetic fabrics and remove tissues in pockets  
before wash. See page 11 for sorting and caring before loading.  
• Do not overload the washer  
• Incorrect sorting  
Lint  
• Tissues left in pocket  
• Overloading the washer  
• Overloading the washer  
• Undissolved detergent  
• Use too much detergent  
Residue or  
detergent  
• Do not overload the washer.  
• Some detergents need to be pre-dissolved, check the detergent  
instructions. Try pre-dissolving the detergent.  
• Increase water temperature using hot water safe for fabric.  
• Use proper amount of detergent.  
Holes, tears,  
or snags  
• Incorrect use of chlorine  
bleach.  
• Never pour chlorine bleach directly on fabric.  
See page 13 for adding liquid bleach.  
• Fasten zippers, hooks, and buckles.  
• Remove objects in pockets. See page 11 for caring before  
loading.  
• Unfastened zippers,  
hooks, buckles  
• Ribs, tears and broken  
threads  
• Overloading the washer  
• Degradation of fabric  
• Do not overload the washer.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-8. TROUBLE SHOOTING METHODS ACCORDING TO ERROR MESSAGE  
For more detailed information for trouble shooting refer to page 38 to 49.  
Error  
Determination  
Expected cause  
Remedy  
• Open water tappet for water  
1. Locked or frozen water tap.  
2. Obstructed water supply.  
supply.  
• Wash at supply condition.  
• Clean or chunge filter.  
3. Top filter of supply valve is  
clogged with dregs.  
4. Connector of supply valve is  
disassembleed or wrongly  
contacted.  
• Reconnect connector or  
adjust wrong contact.  
Water supply doesn't  
reach set level within  
60 minutes.  
INLET Er  
5. Yellow 2 pin connector of  
controller ASM is  
lamp blinks.  
• Reconnect connector and  
adjust wrong contact.  
disassembled or wrongly  
contacted.  
• Check load drive parts of  
TR3, TR4 and TR5, and  
replace related parts.  
6. TR3 (hot), TR4 (cool), TR5  
(shower) are not ON at load  
drive part of controller ASM.  
7. Drain hose is not  
• Hung up drain hose.  
hung up.(Pump Model)  
1.Drain hose is not put down  
(Non Pump Model)  
• Put down drain hose properly.  
(0.9~1.3m high)  
2. Drain hose is bent or  
clogged (Frozen or clogged  
with dregs).  
• Clean clogged drain hose.  
3. Connector of drain motor or  
white 2 pin connector of  
controller ASM is  
• Reconnect connector and  
adjust wrong contact.  
disassembleed or wrongly  
contacted.  
When drain is not  
finished within 12  
minutes at drain  
course.  
DRAIN Er  
4. Wrong drain motor (As AC  
220V is applied to both ends  
of drain motor, the link  
lamp blinks.  
• Replace drain motor.  
opens the drain valve.)  
5. TR8 is not ON at load drive • Check load drive part of TR8.  
part of controller ASM.  
Replace related parts.  
6. Wrong drain pump.  
(Pump Model)  
• Check drain pump.  
• Hang up drain hose properly  
(0.9~1.3m high)  
7. Drain hose is hung up highly  
(over 1.3m)  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Error  
Determination  
Expected cause  
Remedy  
1. Water is partially filled in  
inner tub asm.  
• Fill water evenly into inner tub  
asm.(horizontally)  
2. Machine is slopped (Check • Adjust machine height  
drop position of leveller).  
horizontally.  
SPIN Er  
Unbalanced water for  
spin procedure.  
3. Safety switch is too closer to  
inner tub asm or safety  
• Check and replace safety  
switch.  
lamp blinks.  
switch contacted wrongly.  
4. Is the CONNECTOR of Ball  
Pressure Sensor  
• Check B.P SENSOR  
CONNECTOR or replace B.P  
sensor  
disconnected or badly  
touched?  
1. Lid is opened during all  
washing procedure.  
• Close lid.  
• Close lid.  
DOOR Er  
lamp blinks and  
continuous  
buzz  
2. Lid is opened during  
reservation program.  
Opened lid during  
washing procedure.  
3. Connector of safety switch  
or violet (VI) 2 pin of  
controller asm is  
(wash, rinse and spin)  
• Connect connector again or  
adjust wrong contact.  
disassembled or left wrong  
contact.  
Opened lid during  
delay finish program.  
4. The safety switch is wrong.  
(It is ON in case of the lid  
closed.)  
• Check and replace safety  
switch.  
5. Ball Pressure Sensor is bad  
• Check and replace Ball  
Pressure Sensor.  
or bad contact.  
Frequency generated  
by recognizing water  
level at pressure  
switch is out of  
reference value (below  
15kHz)  
1. The connector of Ball  
Pressure Sensor (Pressure • Connect connector again and  
Switch) or the blue 3 pin  
connector of the controller  
ASM is disassembled or  
connected wrongly.  
adjust wrong contact.  
displayed.  
displayed.  
2. Wrong Ball Pressure Sensor  
(Pressure Switch).  
• Replace Ball Pressure  
Sensor (Pressure Switch).  
3. Wrong controller asm.  
• Replace controller asm.  
1. Defect of inlet valve.  
• Replace the inlet valve.  
Frequency generated  
by recognizing water  
level at pressure switch  
is out of reference  
2. Defect of PWB asm.  
• Replace the PWB asm.  
value (below 22KHz)  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4-9. HOW TO DIAGNOSE AND REPAIR BY SYMPTOM  
1) Washer is not energized.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Household Power supply  
Change the electrical  
.
1. Check whether connection between  
Poor  
Defect of the  
electrical  
the plug and the electrical is poor  
Around rating  
0V  
No defect  
Defect of household  
power supply  
2. Measure voltage of the electrical.  
Call for power supply  
company  
Wiring of the Washer  
1. Measure resistance between both  
ends of the power supply cord with  
both the plug pins short-circuited.  
Less than 1Ω  
No defect  
Open circuit of the  
power supply cord  
∞ Ω  
Change the power  
supply cord.  
Male & female  
connectors  
separated  
Remove the cause to  
give strain and  
2. Check whether every connector in  
the bundle of connectors has a  
good connection.  
Poor connection.  
Wire is opened.  
reconnect them.  
∞ Ω  
Change the lead wire.  
3. Check resistance of every wire to  
find out a open wire.  
Electrical component  
Less than 0.5Ω  
No defect  
Poor contact  
1. Check resistance with power relay  
More than 1.0Ω  
Change the Auto Off  
Switch  
switch turned on  
10~14V  
0V  
2. Check the secondary voltage of the  
transfomer.  
No defect  
Coil is open  
Change the  
transfomerformer  
.
∞ Ω and  
motor is hot  
T.P blown out  
3. Measure resistance to check  
whether the T.P of the motor is  
blown out.  
Remove cause to  
overload the motor  
Open  
Change the fuse.  
4. Check whether the fuse is open.  
Defect of the fuse  
CAUTION  
Check the fuse rating  
AC100~127V:125V 12A  
AC220~240V:250V 6A  
Controller  
If there are no defects in the above,  
it should be defect of the controller.  
If supply voltage is 120% higher than  
rating the varistar in the controller may  
be broken. Check supply voltage.  
Over 120%  
voltage than  
Change the controller  
if all the electrical parts  
rating check  
have no defects.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2) Defects on displaying function  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Main voltage  
To explain that it is  
1. Measure mains voltage at the wall  
Less than 85% Low voltage.  
of the rating.  
caused by low voltage in  
electric supply and  
outlet  
recommend using a  
transfomer if voltage has  
been continuously low.  
To use a transfomer  
having a enough  
capacity if using  
a transfomer.  
2. Meaure voltage at the extended  
outlet that the washer is plugged in  
if the extended outlet is used and  
voltage at the electrical outlet  
is normal in the above.  
Less than 85% The dia of the lead  
of the rating  
wire is smaller or  
many loads are  
connected at the  
same outlet  
Transfomer  
Change the controller.  
Change the controller.  
Defect of the  
transfomer.  
1. Measure the secondary voltage of  
Less than  
AC 10V  
the transfomer.  
Controller  
1. Defect of LED.  
Defect of controller.  
2. Defect of LED driving circuit.  
3. Defect of micom.  
3) Reset During operation  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Mains Voltage  
1. Measure voltage of the outlet that the  
washer is plugged into during wash and  
spin.  
Explain that it is caused  
by low voltage in electric  
mains and recommend  
using a suitable size of  
leads.  
Explain it is caused by  
using environment.  
(It happens when  
equipment with high  
frequency is used  
around)  
Less than  
Mains voltage is too  
80% of the rating. low or size of a lead  
wire is too small.  
External noise  
inrushed.  
2. Reset symptom happens at specific  
time zone repeatedly.  
3. Check whether a transfomerlent  
power cut happens.  
Explain it is a problem of  
electric supply  
(Fluorescent lamp is  
environment.  
transfomeriently blinked.)  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3) Reset during operation  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Drain Motor  
Reset happens  
after the drain  
motor works.  
1. Operate washer setting spin only,  
then press the start/pause button  
when the wash motor starts to work  
and then press the start/pause  
button again in order for the drain  
motor to work intermittently.  
Change the drain motor  
Defect of the drain  
motor (A noise  
generated when the  
internal relay  
works.)  
Controller  
Change the controller.  
1. If mains voltage and the drain motor  
have no defects a defect of the  
controller is highly possible.  
4) Water doesn’t come into the wash tub.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Inlet Valve  
1. If water doesn’t come though the  
inlet valve works(electric sound  
occurs)  
Explain.  
Mains cut.  
Mistake of use.  
Wrong installation.  
1) Check whether water mains is cut.  
2) Check whether tabs are turned on.  
Water mains cut.  
Don’t tumed on.  
Connected  
opposite.  
Turn on the tap.  
Correct their locations  
and turn on the tap.  
3) Hot & cold tab are opposite  
connected.  
4) Wrongly select water temperature  
option.  
5) If there are no problems in the  
above, check the inlet valve filters  
after disconnecting the water supply  
hoses.  
Selected  
opposite.  
Mistake of use.  
Don’t clean.  
Explain how to use.  
Filters blocked  
by foreign  
Clean them by brush  
and explain cleaning  
regulary them.  
substance.  
Defect of the  
inlet valve.  
Change the inlet valve.  
6) If there are no problems in the  
above a diaphragm hole in the valve  
is blocked by foreign substance or  
the plunger in it is locked.  
2. If the inlet valve doesn’t work(there  
is no electric sound)during filling  
cycle.  
Defect of contact.  
Coil is open  
Reconnect it or remove  
the causes to make poor  
connection.  
1) Check whether it’s connectors are  
taken off or they have poor  
connection.  
A connector is  
taken off.  
∞ Ω  
Change the inlet valve.  
2) Check resistance of the inlet valve.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4) Water doesn’t come into the wash bowl.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Ball Pressure Sensor  
Reconnect the connector  
or change leads. Change  
the Ball Pressure Sensor  
(Pressure Switch)  
(Pressure Switch)  
Connector is taken  
off, or lead or coil is  
open.  
PE Error  
displayed.  
1. Is there PE error on the display  
which means Ball Pressure Senosr  
(Pressure Switch) error  
if coil is open.  
Change the  
2. Check frequency of the Ball  
Pressure Sensor(Pressure Switch)  
without load if wash is proceeding  
without filling.  
Less then  
26.2kHz  
Defect of the Ball  
Pressure Sensor  
(Pressure Switch)  
Ball Pressure Sensor  
(Pressure Switch).  
Controller  
1. Defect of controller is highly possible  
if inlet valve and Ball Pressure  
Sensor have no defects in the  
above.  
Change the controller.  
5) Water fills continuously or intermittently.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Wrong Installation/Leakage  
Drain hose  
The drain hose should be  
hung on the  
1. Check whether the drain hose is  
laying down on the floor.  
(For pump model)  
Wrong installation.  
Defect of the part.  
laying down.  
stand-pipe or the tub.  
Change the part.  
Water leaks  
from a part.  
Repair it.  
2. Check where water leaks.  
Ball Pressure Sensor  
(Pressure Switch)  
1. Check the pulsator is rotating when  
water fills continuously.  
It doesn’t  
rotate.  
Check the tube of the  
Ball Pressure Sensor  
(Pressure Switch), it is  
bent or blocked, repair  
that.  
Water pressure is not  
sensed.  
2. If there is no defect in the Ball  
Pressure Sensor(Pressure Switch),  
check whether the air hole of the outer  
tub is blocked.  
Blocked.  
Air hole blocked.  
Repair the blocked hole.  
Inlet Valve  
1. Does water fills even though it is not  
energized (power is off)?  
Defect of the inlet  
valve.  
Water fills.  
Change the inlet valve.  
Change the controller.  
Controller  
Short circuit of the  
triac of the  
1. Does water fill immediately after the  
power switch turns on before pushing  
the start/pause button.  
controller.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6) Pulsator doesn’t rotate normally.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Pulsator rotates at one  
direction.  
Turn the power off  
and on again then that  
symptom disappears.  
Explain “Don’t run wash  
only continuously”.  
Clockwise  
Unusual operation.  
1. The Pulsator rotates normally at the  
beginning of wash cycle, but is it not  
rotate at clockwise direction (locked)  
after some wash cycles though there  
is motor-working sound?  
rotation locked.  
2. In the case the pulsator doesn’t  
rotates either clockwise or  
counterclockwise from the beginning  
of wash cycle:  
Defect of  
Change the controller if  
there are no contact  
defects in the leads of  
the motor.  
controller or poor  
contact of  
connectors of  
motor leads.  
1) Check resistance of the wash  
motor if there is nomotor-working  
sound.  
Resistance  
is normal.  
Adjust belt tension by  
changing motor fixing  
location and change the  
belt if it is impossible to  
adjust belt tension.  
2) Check belt tension & whether the  
clutch rotates normally if there is  
motor-working sound.  
V-belt is loose.  
Clutch locked.  
Loose the belt.  
Change the clutch if the  
clutch pulley is locked  
when making it rotated  
clockwise and  
Defect of the  
clutch.  
counterclockwise by  
hand.  
Adjust belt tension or  
change the belt if it is  
impossible to adjust.  
Loose the belt.  
3. The pulsator doesn’t rotate at both  
directions.  
Motor rotates  
at both  
directions.  
1) Check whether motor rotates at  
both directions if there is motor-  
working sound when it’s  
energized.  
Remove cause  
The plusator  
locked.  
Defect of the  
clutch.  
locking the pulsator  
Change the clutch.  
Change the motor if the  
motor is locked when  
having its shaft rotated  
by hand.  
Defect of the  
Motor doesn’t  
rotates at both  
capacitor.(check  
the capacitor’s  
capacitance)  
directions.  
Change the capacitor if  
there is no contact defect  
in capacitor’s lead  
Defect of the  
motor.  
2) Check resistance of the motor if  
there is no motor-working sound.  
Change the motor.  
∞ Ω  
Motor coil is open.  
Normal  
Remove the causes.  
Contact defect of  
the leads.  
resistance.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6) Pulsator doesn’t rotate normally.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
4. Pulsator weakly rotates.  
Less than 85%  
of rating.  
1) Check voltage at the power outlet  
where the washer is plugged into.  
Explain the causes and a  
transfomer should be  
used if necessary.  
Lower voltage.  
2) Check capacitance of the  
capacitor.  
Capacitor is  
normal.  
Indicating  
needle rises and  
immediately  
indicates ∞.  
The needle is  
stopped after it  
is raised.  
Lack of  
capacitance of the  
capacitor.  
Change the capacitor.  
Change the capacitor.  
Capacitor is fully  
discharged.  
The needle  
doesn’t move.  
7) Water does not drain.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Drain Pump  
Disassemble the drain  
pump cap and remove  
the foreign objects in the  
pump casing.  
Drain pump is  
blocked by foreign  
objects.  
1. Check whether there is drain pump  
There is pump  
working sound.  
working sound.  
Change the drain pump.  
∞ Ω  
It’s coil is open.  
2. Check resistance between terminals  
if there is no working sound of the  
drain pump.  
Defect in  
Repair defected  
connection.  
3. Check connection parts of the leads  
if there is no working sound and its  
resistance is normal.  
Defect in  
connection part.  
connection part.  
Connection part  
has no defects.  
Defect of the  
controller.  
Change the controller.  
Drain Hose  
Kinked.  
Reinstall so that it should  
not be kinked.  
Defect of  
1. Check whether the drain hose is put  
installation.  
in a narrow space and kinked.  
Bent.  
Change the drain rubber  
asm.  
2. Check whether the internal drain  
rubber asm is bent.(For Non-pump  
model)  
Defect of the drain  
rubber asm.  
Submerged or  
higher than  
required.  
3. Check whether the end of the drain  
hose submerged into water or  
higher than required.  
Re-install so that it can’t  
be submerged or not  
higher than required.  
Defect of  
installation.  
(For non-pump model)  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7) Water does not drain.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
4. Check whether the drain hose is  
blocked by foreign objects. It may  
happen in case of the hose is a little  
kinked.  
Blocked.  
Blocked hose.  
Remove the objects and  
reinstall so that it can’t  
be kinked.  
PV Case  
(for Non-Pump Model only)  
Separate the drain motor  
from the PV link,  
Blocked.  
1. Check whether the PV asm is  
blocked by foreign objects.  
disassemble PV cover  
and then remove the  
foreign objects within  
PV case.  
Check the washer works  
normally after repair  
and reassembling them.  
(PV link & drain motor  
lever should be  
assembled accuratel.)  
Drain Motor  
(For Non-Pump Model only)  
Drain motor coil is  
open.  
Change the drain motor  
Check the washer  
works normally after  
reassembling.  
1. Check resistance of the drain  
∞ Ω  
motor if it can not pull the PV link.  
(PV link & drain motor  
lever should be  
assembled accurately.)  
Change the controller if  
there is no defects in the  
connection parts.  
Contact defect in  
connection parts  
or defect of the  
controller.  
Resistance is  
normal.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8) Water drains though it is not the time of drain.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Drain Motor  
(for Non-Pump Model only)  
Change the drain motor.  
Blocked.  
Defect of the drain  
motor.  
1. Check whether the drain motor is  
normally returned after turning  
power off.  
(It is considered normal if the lever  
of the drain motor is fully pulled out  
by the PV spring)  
PV Case  
Remove the objects in  
the PV asm.  
Blocked.  
1. If water drains though the drain  
motor is normally returned, check  
whether PV asm is blocked by  
foreign objects or the bellows in  
the PV asm is deformed.  
Change the PV bellows.  
(The bellows may swell  
up if it contact petroleum  
or petrochemical  
Bellows  
Defect of PV  
Bellows.  
deformed.  
substance because it is  
made of rubber)  
Controller  
1. Check whether the drain motor or  
the drain pump works immediately  
after power is turned on.  
Change the controller.  
Works.  
Defect of the  
controller(Triac  
defect)  
9) Drain error happens while water drains normally.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Ball Pressure Sensor  
Defect of the  
(Pressure Switch)  
Change the Ball  
Pressure Sensor  
(Pressure Swtich)  
Less than  
26.3 kHz  
Ball Pressure  
Sensor(Pressure  
Switch).  
1. Check generation frequency of the  
Ball Pressure Sensor  
(Pressure Switch) without water.  
Change the controller.  
26.3~27.1 kHz  
Defect of the  
controller.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10) Spin extraction is not proceeded.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Motor  
1. In the case that the wash motor does not  
Change the capacitor  
after checking defect of  
capacitor.  
There is motor  
working sound.  
Defect of the  
capacitor or  
Mechanically  
spin during spin extraction;  
check whether the  
1) Check there is motor working  
sound,or  
locked.  
washing clutch or the  
washing tub is blocked  
if the motor rotates after  
removing the V-belt.  
Check whether the  
motor is locked if the  
motor does not rotates  
even though the V-belt  
being removed.  
2) If there is no motor-working  
sound;  
Change the Ball Pressure  
Sensor(Pressure Switch).  
Defect of the  
Less than  
26.3kHz  
Check frequency of the  
Ball Pressure Sensor (Pressure  
Switch), under no load, or  
Ball Pressure  
Sensor (Pressure  
Switch).  
Explain “The lid is close  
during operation”  
Check contact defect of the safety  
switch, defect of connection parts  
and whether the lid is open if door  
error is displayed.  
The lid is open  
Mistake in use.  
Mistake in use.  
Defect of  
Reconnect the conncetors.  
connection part.  
Is placed the magnetic in Lid-B.  
Explain“The lid is close  
during operation”  
The lid is open.  
Defect of magnetic in  
LID-B  
Change the Lid-B  
Contact defect of  
the Ball Pressure  
Sensor(Safety  
Switch)  
Check resistance of the motor.  
Change the Ball Pressure  
Sensor(Safety Switch).  
∞ Ω  
Coil is open.  
Change the motor.  
Drain Motor/Clutch  
1. In the case the motor rotates but the  
inner tub does not rotates;  
∞ Ω  
Resistance is  
normal  
Coil is open.  
Defect of  
Change the drain motor.  
1) Check resistance of the drain  
motor if the drain motor doesn’t  
work,or  
connection part or  
defect of the  
controller.  
Change the controller after  
checking connection parts.  
The clearance is  
less than 2.0mmor  
more then 3.5mm  
Reassemble the drain  
motor or the clutch to  
keep the clearance.  
Assembling defect  
of the drain motor or  
the clutch  
2) Check gap between the PV link  
and the brake lever if the inner  
tub does not rotates while the  
drain motor works.  
The gap is normal  
(2.0~3.5mm)  
Defect of the clutch. Change the clutch.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11) Spining is going on even though the lid is open.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Safety Switch  
1. Check resistance between both  
terminals of the safety switch with  
the lid open.  
Contact points of  
the safety switch  
are welded.  
Change the Safety  
Switch  
0~9Ω  
Defect of the  
controller.  
Change the controller  
∞Ω  
Reed S/W is short  
by magnetic on  
the washer.  
Keep magnet away from  
the washer.  
Ball Pressure Sensor  
1. Is placed the magnetic on the wash?  
Yes  
No  
Reed Switch.  
Change the controller.  
12) Spin basket doesn’t reach to full speed(normal rpm)  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Main voltage  
Explain the cause and  
recommend using a  
transfomerformer if  
necessary.  
Tool low voltage  
Less than  
1. Check voltage at the power outlet  
85% of rating  
where the washer is plugged into.  
Change the capacitor  
Lack of  
Defect of  
capacitor  
Starting Capacitor  
capacitance  
1. Check the capacitance of the  
starting capacitor.  
Clutch Assembling  
Adjust PV lever bolt and  
paint it red.  
1. Check the clearance between the  
PV link and the brake lever and  
clearance between the clutch lever  
and the adjustment bolt.  
The clearance is  
less than 2.0mm  
or more than 3.5mm  
Reassemble the drain  
motor or the clutch.  
Adjust the bolt  
clearance.  
Bolt clearance is  
out of range  
1.9±0.1mm  
Defect of the  
clutch  
Blocked by foreign objects  
Remove the foreign  
objects.  
1. Check whether the PV asm, the  
drain pump & the drain hose are  
blocked by foreign objects so that it  
makes water-splashing noise in the  
tub.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13) Vibration, Noise or Unbalance Error happens during spin.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Using conditions such as  
installation etc.  
Level the washer.  
Not leveled.  
Defect of  
1. Check whether the washer is  
leveled. (Check clearance with out  
tub and out case the left gap is the  
same as the right and the rear gap is  
1.5~2 time bigger than the front gap,  
between the cabinet and the wash  
bowl, when it is leveled.)  
installation  
2. Check whether laundry in the wash  
bowl is out of balance that can  
cause severe vibration & noise.  
Laundry is  
unbalanced.  
Explain that it is not out  
of order and it may  
happen when big & long  
laundry is washed.  
Change the clutch  
spring-B or the clutch  
asm.  
3. Check whether the pulsator doesn’t  
rotate during spin.(To check that,  
The pulsator  
Defect of the  
clutch  
rotates initially  
remove the front lid and than run the then the inner tub  
spin only cycle.)  
rotates.  
Safety Switch  
1. Check whether the lever of the  
safety switch touchs the outer tub if  
touching noise happens.  
Change the safety  
switch.  
The lever is  
bented  
Defect of the  
safety switch  
Don’t repair and reuse it  
because it creates  
another problem if it is  
wrongly repaired.  
Damper  
1. Check whether the outer tub cover  
hit the top cover without load  
during spin.  
Defect of the  
damper  
Hit  
Change four dampers  
simultaneously.  
(In assembling, check  
the position to damper  
asm)  
It is very important to find out what kinds of noise & where comes from to settle  
noise during spin and accumulately service experiance.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14) Power is automatically turned off during operation or immediately  
turning on the power switch.  
Where, what & how to check? Result of Check Possible Cause How to repair & settle  
Main voltage  
Defect in main.  
Explain the cause.  
(It happens specially  
when a high frequency  
equipment is a used  
around the washer or in  
the case voltage  
1. It is mostly caused by noise from  
mains or transfomerient power cut.  
fluctuation is big)  
Auto Off switch or  
Controller  
1.Check whether power is  
automatically turned off when  
turning on the auto off switch after  
unplugging the power cord from the  
outlet  
Automatically  
turned off  
Mechanical defect  
of the auto off  
switch.  
Change the auto off  
switch.  
2. It would be defect of the controller if  
power is automatically turned off  
immediately when turning on the  
power switch even though there is  
no defects in the auto off switch.  
Change the controller.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. EXPLODED VIEW  
TOP COVER  
ASSEMBLY  
TUB  
ASSEMBLY  
OUT CASE  
ASSEMBLY  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5-1. THE EXPLODED VIEW OF TOP COVER ASSEMBLY  
A210  
A020  
A330  
A011  
A024  
A053  
A030  
A040  
A160  
A220  
A026  
A050  
A180  
A060  
A202  
A200  
A201  
A191  
A152  
A170  
A110  
A190  
A151  
A192  
A100  
A 120  
A230  
HOT(ORANGE)  
COLD(BLUE)  
A277  
A273  
A274  
A240  
HOT(ORANGE)  
COLD(BLUE)  
HOT(ORANGE)  
COLD(BLUE)  
A271  
A272  
A275  
A276  
A270  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5-2. THE EXPLODED VIEW OF OUT CASE ASSEMBLY  
: Non-Service Part  
F070  
F010  
F001  
F080  
F082  
F000  
F084  
F081  
F020  
F090  
F021  
For Pump  
F027  
F100  
F050  
For Non-Pump  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5-3. THE EXPLODED VIEW OF TUB ASSEMBLY  
: Non-service part  
K000  
K090  
K012  
K011  
K010  
K021  
K025  
K022  
K024  
K023  
K020  
K027  
K028  
K060  
K030  
K063  
K062  
K160  
K040  
K050  
K201  
K200  
K061  
K111  
NATURAL  
K101  
K210  
K220  
K110  
BLUE  
K102  
K064  
K250  
K230  
For Pump  
For Non-Pump  
K140  
K270  
K130  
K271  
K272  
or  
For Non-Pump  
K273  
K274  
K150  
K276  
K277  
K278  
K275  
K170  
K263  
K262  
or  
K120  
K180  
K261  
K260  
For Non-Pump  
K280  
K190  
For Pump  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  

La Crosse Technology Weather Radio WS 2510 User Manual
Lenovo Computer Hardware 3000 C200 User Manual
Magic Chef Fryer MCSDF6ST User Manual
Makita Drill 6017D User Manual
Makita Power Hammer HM1100 User Manual
Manitowoc Ice Ice Maker K00365 User Manual
Marantz Projector VP 12S2 User Manual
McCulloch Trimmer MT3310 User Manual
Mercedes Benz Automobile 2002 CL 500 User Manual
Middleby Cooking Systems Group Oven HW 2 1 2G User Manual