LG Electronics VCR TL AT130M User Manual
TIME LAPSE VCR  
SERVICE MANUAL  
CAUTION  
BEFORE SERVICING THE UNIT, READ THE “ SAFETY PRECAUTIONS”  
IN THIS MANUAL.  
MENU  
REC  
REW  
REV  
F. F  
POWER / TIMER  
CUE  
MOVE  
DOWN  
SEL  
UP  
TRACKING  
ALARM  
KEY  
PAUSE / STILL  
LOCK  
REC / PB SPEED  
PLAY  
/
REC CHK  
STOP / EJECT  
APRIL, 2006  
Printed in Korea  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION1 SUMMARY  
SPECIFICATIONS  
GENERAL  
Head System  
Power Source  
Four head helical scan azimuth system  
AC 100-240V, 50/60Hz  
Power Consumption  
Back up time (clock)  
Dimensions (WxHxD)  
Operating Temperature  
Operating Humidity  
Timer  
Approx. 15 Watts  
30 days  
14.2” x 3.7” x 10.7” (360 x 94 x 273 mm)  
41 °F~105 °F (5 °C~40 °C)  
Less than 80% RH  
24-hour display type  
Weight  
Approx. 8.4 lb (3.8 kg)  
Tape Speed (NTSC)  
11.12 mm/sec (6H) , 3.70 mm/sec (18H),  
2.22 mm/sec (30H), 72H ~ 960H  
11.695 mm/sec (6H) , 3.89 mm/sec (18H),  
2.33 mm/sec (30H), 72H ~ 960H  
Tape Speed (PAL)  
Maximum Recording Time  
6 hours (NT:T-120/PAL:E-180, 6H),  
18 hours (NT:T-120/PAL:E-180, 18H),  
30 hours (NT:T-120/PAL:E-180, 30H), 72H ~ 960H  
0.5 in. (12.7 mm)  
Tape Width  
Rewind Time  
Video Signal System(PAL)  
About 65 seconds (NT:T-120)(PAL:E-180)  
CCIR Standard (625 lines, 50 fields)  
PAL type color signal  
Video Signal System(NTSC)  
EIA Standard (525 lines, 60 fields)  
NTSC type color signal  
Video Input  
Video Output  
1.0 Vp-p 75 ohms unbalanced  
1.0 Vp-p 75 ohms unbalanced  
More than 43 dB (6H mode)  
Signal to Noise Ratio  
Conventional audio  
Input (LINE)  
Output (LINE)  
S/N Ratio  
-6.0 dBm more than 47 kohms  
-6.0 dBm less than 1.5 kohms  
More than 43 dB (6H mode)  
200 Hz to 10kHz (6H mode)  
Frequency Range  
* Designs and specifications are subject to change without notice.  
* Weight and dimensions shown are approximate.  
1-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION1 SUMMARY  
LOCATION OF CUSTOMER CONTROLS  
FRONT  
1 POWER/TIMER BUTTON  
2 MENU BUTTON  
3 REC (RECORD) BUTTON  
4 MOVE BUTTON  
10 CASSETTE LOADING SLOT  
11 CLEAR, KEY LOCK OFF, BUZZER OFF  
12 CLOCK, COUNT, REMAIN  
13 SHUTTLE RING  
5 SEL (SELECT) BUTTON  
6 DOWN BUTTON  
7 UP BUTTON  
8 ALARM INDICATOR  
9 KEY LOCK INDICATOR  
14 JOG RING  
15 PAUSE/STILL BUTTON  
16 PLAY/REC CHECK BUTTON  
17 STOP/EJECT BUTTON  
REAR  
1 POWER CORD  
4 RESET BUTTON  
2 AUDIO IN/OUT JACK  
3 VIDEO IN/OUT JACK  
5 12-PIN TERMINAL BLOCK  
1-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION1 SUMMARY  
LOCATION OF CUSTOMER CONTROLS  
INDICATOR PANEL  
1
2
3
4
5
6
TIME LAPSE VCR TIME INDICATION  
ALARM INDICATION  
SERIES INDICATION  
RECORD INDICATION  
TIMER INDICATION  
CASSETTE INDICATION  
7
8
9
INDEX INDICATION  
POWER FAILURE INDICATION  
KEY LOCK INDICATION  
10 REPEAT INDICATION  
11 FUNCTION INDICATION  
12 VCR FUNCTION INDICATION  
VCR FUNCTION INDICATION  
1-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION1 SUMMARY  
LOCATION OF CUSTOMER CONTROLS  
TERMINAL SIGNAL LEVELS  
TERMINAL  
SIGNAL LEVEL  
IN/OUT  
DESCRIPTION  
VIH : 4 ~ 5V  
VIL : 0 ~ 0.6V  
The input signal that makes  
‘Alarm Record’ work  
1. ALARM IN  
INPUT  
T
: above 250 msec  
VIH : 4 ~ 5V  
VIL : 0 ~ 0.6V  
Outputs whether ‘Alarm  
Recording’ is working  
2. ALARM OUT  
3.ALARM RESET  
5. SERIES IN  
OUTPUT  
INPUT  
T
: ALARM REC STATE  
VIH : 4 ~ 5V  
VIL : 0 ~ 0.6V  
The terminal that stops ‘Alarm  
Record’ in Auto mode  
T
: above 250 msec  
VIH : 4 ~ 5V  
VIL : 0 ~ 0.6V  
The input terminal to make  
‘Series Record’ work  
INPUT  
T
: above 250 msec  
Output signal appears when the  
tape reaches to end or deck is  
error in recording.  
VIH : 4 ~ 5V  
VIL : 0 ~ 0.6V  
6. SERIES OUT  
7. WARNING OUT  
8. TRIGGER OUT  
10. LOW TAPE OUT  
11. 1-SHOT REC IN  
4, 9, 12. GND  
OUTPUT  
OUTPUT  
OUTPUT  
OUTPUT  
INPUT  
T
: above 250 msec  
VIH : 4 ~ 5V  
VIL : 0 ~ 0.6V  
Outputs whether VCR deck is  
error.  
T
: until any-key is pressed  
The signal is output which is used by  
switching several cameras in  
general space with using camera  
multi-plexer.  
VIH : 4 ~ 5V, VIL : 0 ~ 0.6V  
8 msec : NTSC  
10 msec : PAL  
As the terminal that outputs that tape  
remains less than 5 minutes in  
recording, it isn’t output in ‘1-shot  
Record’.  
VIH : 4 ~ 5V  
VIL : 0 ~ 0.6V  
T
: below 5 min, end of tape  
VIH : 4 ~ 5V  
VIL : 0 ~ 0.6V  
The terminal that makes ‘1-short  
Record’ work in Auto mode  
T
: above 250 msec  
COMMON  
-
0V  
1-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION1 SUMMARY  
CRITICAL PARTS REPLACING TIME TABLE  
No. DESCRIPTION  
1500 3000 5000 6000 7500 9000 10000 12000 Test freatures  
Specification  
1
2
3
4
5
6
7
8
9
DRUM ASSY  
RF out level  
Wear status  
W/F(WTD)  
-4dB and below  
Whether extraneous  
matters come out  
ARM ASSY CLEANER  
MOTOR CAPSTAN (D-35)  
BELT CAPSTAN  
0.4% and below  
Variation amount :  
within 40%  
Belt tension  
Audio and CTL out  
level  
The rate of erasing  
(1KHz)  
The capacity of ldler  
for moving  
Surrace solidity of  
Roller  
BASE ASSY A/C  
-6dB and below  
45dB min  
4~12 g  
HEAD F/E  
ARM ASSY IDLER  
HOLDER ASSY PINCH  
BAND ASSY TENSION  
60~90  
Back Torque  
40~70 g  
there shouldn’t be any space  
betwween CST and compartment  
10 HOUSING ASSY  
11 CAPSTAN SOFT BRAKE  
12 CLUTCHAY  
CST loading status  
Felt wear  
whether there is  
touch noise  
40~140gcm, 100~210gcm  
Torque(Play, Rev)  
Reference :  
Changing  
Cleaning  
Checking  
Notes :  
• Check the running path adjustment when you change the itens 1, 3, 5, 6 and 10.  
• Check the back tension when you change Band Assy Tension.  
CRITICAL PARTS DESCRIPTION  
1. Drum Ass’y  
Consists of video head, rotary trans and motor. records video and audio information on  
the tape, and play the tape back.(Audio information is recorded only on the Hi-Fi models)  
2. Arm Ass’y Cleaner  
4. Motor Capstan  
5. Belt Capstan  
Cleans video head and rotation head automatically.  
Moves the tape with regular speed.  
Transfers rotative energy of capstan motor to the driving system.  
Brakes rotative energy of capstan motor.  
6. Brake Ass’y Capstan  
7. Base Ass’y A/C  
Consists of three head.  
Audio erase head in the left upper erases audio signal in dubbing.  
Audio head in the right upper records and playes the audio signal.  
CTL head in the right lower records and detects CTL pulse to control tape speed.  
8. Head F/E  
Is abbreviation of Full Erased Head.  
erases the signal recorded on a tape clearly and absorb vibration of tape.  
12. Arm Ass’y Idler  
13. Holder Ass’y Pinch  
Is located between T/UP reel and supply reel.  
Transfers ratative energy of capstan motor to T/UP reel or supply reel.  
Sticks a video tape to capstan motor and has the tape played without being  
slipped from capstan motor axle.  
14. Band Ass’y Tension  
15. Arm Ass’y  
Has supply reel loosened properly with giving it some tensile force.  
Makes the cassette tape inserted be loaded and ejected precisly and safely.  
Plays the tape with trasfering rotative energy of capstan motor to idler reel.  
16. Clutch Ass’y  
1-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION2 CABINET & MAIN FRAME  
EXPLODED VIEWS  
1 . Ca b in et a n d Ma in Fra m e Sect io n  
Ca b in et & Ma in Fra m e Sect io n Pa rt s list  
MODEL : TL-AT130M  
RUN DATE : 2004.03.12  
REMARKS  
S AL LOCA.NO. PART NO  
DESCRIPTION  
SPECIFICATION  
ASSEMBLY SECTION  
DECK ASSEMBLY,VIDEO  
A00  
A42  
A43  
A44  
A45  
A46  
6721R-0771U  
DECK/MECHA D35 LG T/L (4HD(ALL  
6871R-8283A  
3721R-F826D  
6871R-4462A  
6871R-7050B  
3501R-7050B  
PWB(PCB) ASSEMBLY,TOTAL T/L VCR KEY2 JOG/SHUTTLE  
PANEL ASSEMBLY,FRONT  
PWB(PCB) ASSY,TOTAL  
CCD TIME LAPSE PANEL FRONT ASS  
TL-AR30 (SERIES) - W. RS232C -  
PWB(PCB) ASSEMBLY,TOTAL T/L VCR TL-AT130M MAIN  
BOARD ASSEMBLY  
PARTS SECTION  
CASE  
VCR TL-AT130M MAIN  
250  
260  
277  
278  
280  
281  
283  
284  
285  
286  
300  
320  
3110R-S040F  
3210R-0023A  
4940R-Z075A  
4940R-Z076B  
3720R-F721D  
524-013A  
LV-TL1960 2960 MOLD AIRHALL BA  
VCR - MAIN  
FRAME  
KNOB  
SHUTTLE(TL-AR30M)  
KNOB  
CCD TL-AT130 MOLD  
PANEL,VIDEO  
MAGNET  
DOOR  
CCD LV-TL1960 S MOLD HIPS 40AF  
VCR - ASSY DOOR  
3580R-V090A  
442-681A  
CCD TIME LAPSE MOLD DOOR CST  
DOOR  
SPRING  
4940R-Z086A  
4940R-S017A  
KNOB  
CCD LV-TL124 MOLD  
KNOB  
SLIDE (LV-TL24)  
6410RZHV01A POWER CORD  
IT10S2(6A/250V) VOLEX IMMETRO  
LV-TL1960S 2960S NEW ASSY (RS-  
3721R-D031N  
PANEL ASSEMBLY,  
DISTRIBUTOR[NOR  
CASE ASSY  
323  
325  
330  
3111R-0089B  
4931R-0024D  
3550R-0210A  
PRE-AMP (PBSB-SH)  
DIGI(MONO-ENABLE)  
BOTTOM(LARGE)  
HOLDER ASSEMBLY  
COVER  
SCREW  
452  
457  
462  
353-051A  
353-051E  
353-136A  
SCREW,DRAWING  
SCREW,DRAWING  
SCREW,DRAWING  
SPECIAL  
SPECIAL (3X12)  
SPECIAL(FBK) (353S353A)  
2-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION2 CABINET & MAIN FRAME  
EXPLODED VIEWS  
1 -1 . Ca b in et a n d Ma in Fra m e Sect io n  
Cabinet & Main Frame Section Parts list  
ASSEMBLY PARTS SECTION  
A42  
A43  
A44  
A46  
6871RK5700K  
05503805  
Ass'y Front PCB  
SNILN4T3526  
ASS'Y FRONT CAVINET  
Ass'y Ant. PCB  
NTH960 C-TYPE  
TL-AR30(SERIES)  
CCD LV-TL1960  
6871R-4462A  
3501RK3200B  
Ass'y Main PCB  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION2 CABINET & MAIN FRAME  
EXPLODED VIEWS  
2 . Pa ckin g & Accesso ry Sect io n  
✒
NOTE  
Refer to “REPLACEMENT PARTSLIST” in order to look  
for the part num ber of each part.  
801 INSTRUCTION ASS’Y  
803 : PACKING  
804: SHEET ROLL  
802: BOX CARTON  
• Packing Accessory Section Parts list  
MODEL : TL-AT130M  
RUN DATE : 2004.03.12  
REMARKS  
S AL LOCA.NO. PART NO  
DESCRIPTION  
SPECIFICATION  
801  
802  
803  
804  
808  
900  
3835RS0069N INSTRUCTION ASSEMBLY  
CCD TL-AT330M-AABBDL1_ENG_POR_  
TL-AT330M AABBDL . 1  
3890R-C065K  
3920R-E016A  
3858R-S001A  
534-008C  
BOX,MASTER  
PACKING  
Packing LV-TL24I 0.02 0 EPS 10  
Packing LDPE 600M 630MM 0.5 VC  
AAAM(R03) SEOTONG 1-5 V - 1PA  
P9 LV-TL1960  
SHEET (MECH)  
BATTERY,MANGANESE  
6711R1P041H REMOTE CONTROLLER  
ASSEMBLY  
2-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
ELECTRICAL ADJUSTMENT PROCEDURES  
1 . PG ADJUSTMENT  
MODE  
SPECIFICATION  
PG : 416 ± 20  
OBJECT MEASURED  
V.OUT JACK  
OBJECT ADJUSTED  
VR501  
PLAYBACK IN SP  
sec  
1. Connect CH-1 of the oscilloscope to W357 and W362,  
and adjust it to 1Vp-p as TRIGGER.  
WAVEFORM  
(In case of 10:1 Probe, adjust it 50m Vp-p)  
2. Connect CH-2 of the oscilloscope to V.OUT JACK and  
adjust it to 0.5Vp-p.  
(In case of 10:1 Probe, adjust it 50 Vp-p)  
3. Adjust time of the oscilloscope to 0.1 msec.  
4. Adjust the range between FLLING EDGE part of video  
vertical trigger signal and video vertical trigger signal  
to the specification(416±20  
) with changing VR501.  
sec  
•
CONNECTION CHART OF MAIN PWB  
Fig 3-1. Connection chart of PG adjustment  
✒
Ca u tio n  
When repairing the power part just after pulling out the power code, there is hazard of electical shock caused by the  
charged electricity at the peripheral circuit com ponent(prim ary power) such as condenser C807(150µF). So begin  
repairing after doing procedure below.  
1. Set the volt m eter up to resistance m easurem ent.(In case of digital volt m eter, set it up to over 20MΩ.)  
2. Discharge electicity with putting the m easuring term inal lines(+, 1 probe) of volt m eter at the ends of condenser  
C103.(You don’t have to put the polarity of the m easuring term inal lines on the sam e polarity of the condenser.)  
3-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
ELECTRICAL TROUBLESHOOTING GUIDE  
1 . Po w er Circu it (SMPS)  
(1 ) No 5 .3 A  
(2 ) No 9 V  
No 5.3V  
No 12V  
NO  
NO  
NO  
Replace F101(Use a specified  
fuse).  
Is F101 normal?  
Is D109 normal?  
Check/Replace D109  
Replace Q170  
YES  
YES  
NO  
Is Q170 normal?  
Is BD101 normal?  
Replace BD101.  
Replace R101.  
YES  
YES  
NO  
NO  
NO  
NO  
Is R101 normal?  
YES  
Is D110 normal?  
Replace D110  
Replace Q152  
YES  
Is there Vcc (about 13~19V) at  
IC101 pin 5?  
Is D103 normal?  
Is Q152 normal?  
YES  
NO  
Check/  
Check/ Replace Q163  
Replace D103  
YES  
NO  
NO  
Is D106 normal?  
Replace D106.  
(3 ) No 2 4 V  
YES  
No 24V  
Is there about 2.5V at  
IC103 pin 1?  
Replace IC103.  
YES  
NO  
NO  
NO  
NO  
Replace D109.  
Is D110 normal?  
YES  
Is D109 normal?  
YES  
Check/Replace D110  
Check/Replace Q152  
Is Q159 normal?  
YES  
Is L103 normal?  
Is L103 normal?  
YES  
Check the power terminal at main  
PCB short.  
Check ‘H’ signal at Q161  
Base terminal  
3-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
ELECTRICAL TROUBLESHOOTING GUIDE  
(4 ) No 5 .2 A (TO AVCP, BIAS)  
(5 ) No 1 0 V  
No 5.2V  
No 10V  
NO  
NO  
Is D106 normal?  
Replace D106.  
Is D109 normal?  
Replace D109  
YES  
YES  
Is Q170 normal?, Is there about  
13.5V at Q107 Base?  
NO  
NO  
Check/ Replace  
Q107, ZD103  
Is Q153 normal?  
Replace Q153.  
Replace Q157.  
YES  
YES  
Is there voltage (about 0V)  
Check/ Replace  
NO  
at Q157 collector.  
D155, D156, D157/\.  
YES  
Check/  
Replace Q156  
3-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
ELECTRICAL TROUBLESHOOTING GUIDE  
2 . SERVO CIRCUIT  
(1 ) Vid eo is u n st a b le in PB m o d e  
In PB mode  
Does noise level on the screen  
change periodically?  
YES  
NO  
Does CTL pulse appear at  
IC501 Pin 76?  
Readjust the height  
of CTL fead.  
NO  
Is adjusting height of CTL  
head accurate?  
YES  
NO  
Replace IC501.  
Does CTL pulse move on tracking?  
YES  
Does Video Envelope wave form  
appear at IC501 pin 86?  
NO  
Check the Pre-Amp circuit  
YES  
Replace IC501.  
(2 ) Dru m m o t o r st o p s  
When the drum moter stop  
NO  
Is there 12V at PMC01 Pin8?  
Check Power circuit  
YES  
NO  
NO  
Does DFG pulse appear at  
PMC01 Pin3?  
Does Drum PWM pulse  
appear at IC501 Pin34?  
Is there 2.8V at PMC01 Pin12?  
YES  
NO  
YES  
YES  
Aren’t pattern or componets between  
Check the Ass’y between  
Check the Ass’s between  
IC501 Pin34 and PMC01 Pin12 short?  
junction PCB and Drum motor  
connector(PMC01) and Drum motor  
Does DFG pulse appear at  
IC501 Pin65?  
Aren’t pattern or componets between  
IC501 Pin34 and PMC12 Pin1 short?  
NO  
NO  
YES  
Does Drum PWM pulse appear  
at IC501 Pin34?  
Replace IC501  
YES  
Aren’t pattern or componets between  
IC501 Pin34 and PMC01 Pin12 short?  
3-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
ELECTRICAL TROUBLESHOOTING GUIDE  
(3 ) Ca p st a n m o t o r st o p s  
When the capstan motor stops  
NO  
Is it 12VA at PMC01 Pin2?  
Check Power circuit  
YES  
NO  
Is there 2.8V at PMC01 Pin9?  
Does PWM signal appear at IC501 Pin 33?  
YES  
YES  
Check the Ass’y between PMC01  
and Capstan motor  
NO  
YES  
Aren’t pattern or componets between  
IC501 Pin33 and PMC01 Pin9 short?  
Does CFG signal appear at PMC01 Pin1?  
YES  
NO  
Check the Ass’y of Capstan motor  
NO  
Check CFG signal appear at IC501  
Pin67?  
Aren’t pattern or componets between IC501 Pin67 and  
PMC01 Pin1 short?  
YES  
Does Capstan PWM signal appear  
at IC501 Pin33?  
NO  
Replace IC501  
YES  
Aren’t pattern or componets between  
IC501 Pin33 and PMC01 Pin1 short?  
3-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
ELECTRICAL TROUBLESHOOTING GUIDE  
3 . Y/C CIRCUIT  
(1 ) No Vid eo in EE Mo d e  
No Video in EE Mode  
NO  
Does the Video signal appear at the  
IC3G1 Pin9?  
Check the Video input Jack &  
jack Board connection.  
YES  
NO  
Does the Video signal appear  
at the IC301 Pin38?  
Check the IC3G1 Pin14  
and Q3G1 emitter.  
YES  
NO  
NO  
Check the 5VA Line.  
(Power Circuit)  
Is 5V applied to the  
IC301 Pin16, 40, 55, 58, 75, 87?  
YES  
Is I2C BUS signal applied to the  
IC301 Pin 23, 24?  
Does the Video signal appear  
at the IC301 Pin29?  
Check the System Circuit. (Refer to  
‘SYSTEM I2C BUS Trouble Shooting’)  
NO  
NO  
YES  
YES  
NO  
NO  
Does the Video signal appear  
at the IC501 Pin 47?  
Check the path of the signal between  
the IC301 Pin29 and IC501 Pin49.  
Check C316.(AGC)  
YES  
YES  
Is there 9V on the plus  
terminal of the C381?  
Does the Video signal appear at  
the Emitter terminal of the Q380?  
Replace the IC301.  
NO  
YES  
Check the 9V Line.  
(Power Circuit)  
Replace the Q380.  
3-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
ELECTRICAL TROUBLESHOOTING GUIDE  
(2 ) Wh en t h e Y(Lu m in a n ce)sig n a l d o esn ’t a p p ea r o n t h e screen in PB Mo d e.  
NO  
Is 5V applied to the IC301  
Pin 16, 40, 55, 58, 87?  
Check the line of the 5.3VA  
Line. (Power Circuit)  
Is the I2C Bus signal applied  
to the IC301 Pin 23, 24?  
NO  
Check the System Circuit. (Refer to  
‘SYSTEM I2C BUS Trouble Shooting’)  
YES  
NO  
NO  
Check the System Circuit.  
(IC501 Pin 23)  
Does the normal RF signal  
appear at the IC301 Pin74?  
Is the V.H.S/W "H" about  
3.4V to the IC301 Pin11 ?  
YES  
NO  
Check the V.H.S/W level.  
(Check R304, R305)  
Is V.H.S/W "H" about 3.4V at the  
IC301 Pin 11?  
YES  
YES  
NO  
Replace the IC301.  
Clean the Drum.  
NO  
NO  
Does the Y(Luminance) RF signal  
appear at the IC301 Pin 17?  
Check the path of the Y(Luminance)  
RF signal.(Check the Q301)  
YES  
YES  
Check the path of the Y(Luminance)  
RF signal.(Check Q302, Q303)  
Is the Y(Luminance) Video waveform  
showed up at the IC301 Pin 41?  
YES  
YES  
Replace the IC301.  
3-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
ELECTRICAL TROUBLESHOOTING GUIDE  
(3 ) Wh en t h e C(Co lo r) sig n a l d o esn 't a p p ea r o n t h e screen in PB Mo d e  
NO  
Is 5V applied to the IC301  
Pin 16, 40, 55, 58, 87?  
Check the line of the 5.3VA  
Line. (Power Circuit)  
NO  
NO  
Is the Color Rotary signal applied to  
the IC301 Pin 10?  
Check the Color Rotary  
Circuit. (IC501 pin 98)  
YES  
Is Color Rotary "H" about  
1.6V?  
Check the Color Rotary level.  
(Check the R302, R303)  
YES  
NO  
Does the Color signal appear at  
the IC301 Pin 71?  
Does the X301(4.43MHz) or  
NO  
NO  
Replace the X301 or the X302.  
X302(3.58MHz) oscillate?  
YES  
Check the Color Pass.  
(Check the Q304)  
Does the Color signal appear  
at the IC301 Pin 61?  
YES  
YES  
NO  
Check the circuit of the  
IC301 Pin 35, 62.  
Replace the IC301.  
Replace the IC301.  
(4 ) Wh en t h e Vid eo sig n a l d o esn 't a p p ea r o n t h e screen in REC Mo d e.  
NO  
Is the EE signal normal?  
Check EE Mode.  
NO  
Is 5V applied to the IC301  
Pin 16, 40, 55, 58, 87?  
Check the line of the 5.3VA  
Line.(Power Circuit)  
YES  
NO  
Does PB Mode operate  
normally?  
Check PB Mode.  
YES  
NO  
Does the RF signal appear at  
the IC301 Pin 12?  
Is the REC 'H' signal (about  
Check the System of REC 'H'  
(the IC501 Pin 30 / the D301)  
NO  
4V)applied to the IC301 Pin 30?  
YES  
YES  
Check REC Luminance  
Pass & Color Pass.  
Replace the IC301.  
YES  
NO  
YES  
Check the circuit of the  
IC301 Pin 90, 92, 94  
Does the REC RF signal appear at  
the IC301 Pin90?  
YES  
Check the Drum &  
Drum Connector  
3-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
ELECTRICAL TROUBLESHOOTING GUIDE  
4 . AUDIO CIRCUIT  
(1 ) No so u n d in EE Mo d e  
(2 ) No so u n d in PB MODE  
No sound in EE Mode.  
No sound in PB Mode.  
YES  
YES  
No sound.  
YES  
No sound.  
YES  
NO  
NO  
Is 5V applied to the IC301  
Pin 75?  
Is 5V applied to the  
IC301 Pin 75?  
Check the line of the 5V Line.  
(Power Circuit)  
Check the line of the 5V Line.  
(Power Circuit)  
YES  
YES  
Does the CLK/Data signal(I2C)  
appear at the IC301 Pin 23, 24?  
NO  
NO  
Check the IC501 Pin 18(CLK),  
17(Data) Line.  
Is the Audio signal applied to the  
IC301 Pin 76?  
Check the path of  
LINE/AUDIO.  
YES  
YES  
NO  
Check the connecting State between  
the P3D02 Pin 6 and A/C Head.  
Does the Audio signal appear  
at the IC301 Pin 1?  
NO  
NO  
Is the Audio Mute "High" signal applied  
to the IC301 Pin 10?  
Does the Audio signal appear  
at the IC301 Pin 96?  
YES  
YES  
YES  
YES  
Is the Audio Mute "H" applied to  
the IC301 Pin 10?  
Does the Audio signal appear  
at the IC301 Pin 96?  
Check the IC501 Pin 2.  
(Audio Mute "H".)  
Check the connection of the Audio  
out Jack.  
NO  
YES  
NO  
YES  
Does the CLK/Data signal(I2C)  
appear at the IC301 Pin 23, 24?  
Check the IC501 Pin18(CLK),  
17(Data) Line.  
Replace the IC301  
Check the IC501 Pin2.  
NO  
YES  
Replace the IC301  
3-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
ELECTRICAL TROUBLESHOOTING GUIDE  
(3 ) No so u n d in REC Mo d e.  
NO sound in REC Mode.  
YES  
Sound is not recorded.  
YES  
NO  
Refer to "No sound in PB  
Is Playback O.K.?  
Mode,".  
YES  
NO  
Is the Audio signal applied  
Check the path of Line Audio.  
to the IC301 Pin 76?  
YES  
NO  
NO  
Is the “High” signal applied to the  
IC301 Pin 10?  
Check the CLK/Date line and  
replace the IC301  
Does the Audio waveform appear  
at the IC301 Pin 7?  
YES  
YES  
Is 5V applied to the FL401  
Pin 2?  
Check the IC501 Pin 96  
(Audio Mute “H”).  
NO  
NO  
NO  
NO  
YES  
Is 3.0~4.5V applied to the Emitter  
of the Q481?  
Check the line of the 5V  
Power Circuit.  
YES  
Does the Erase signal  
appear at the FL401 Pin 6?  
YES  
Is the Voltage level of the IC301  
Pin6 850mVp-p?  
Replace the FL401 or the  
Q405.  
Check the Audio R/P/E  
connector and Head.  
3-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
ELECTRICAL TROUBLESHOOTING GUIDE  
5 . SYSTEM/KEY CIRCUIT  
(1 ) AUTO STOP  
Auto Stop  
YES  
NO  
Does SW waveform appear at IC501  
pin23?  
Check Drum motor signal  
YES  
NO  
NO  
Does T/up reel pulse appear  
at IC501 Pin27?  
Does T/up reel pulse appear  
at Q514 Base terminal?  
Is there 5.3V at RS501?  
NO  
YES  
YES  
YES  
Replace T/up reel sensor of deck  
Check power circuit  
Check DP06, LP03  
Replace IC501  
(2 ) No ca sset t e t a p e lo a d in g  
No cassette tape loading  
YES  
NO  
Is there REG. 12V at PMCQ1  
Pin8?  
Check power circuit L104.  
YES  
NO  
Does 'H' signal appear at IC501  
Pin62 while inserting CST?  
Is there 5.3V at IC501 Pin73?  
YES  
NO  
Check CST SW and peripheral circuit  
Check power circuit  
Check D106, L103.  
NO  
YES  
Check IC501 Pin7, 8, 9, 10  
Check Deck mechanism  
*C a u t io n : Auto stop can occur because Grease or Oil is dried up  
3-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
ELECTRICAL TROUBLESHOOTING GUIDE  
(3 ) No Key d isp la y  
No Key display  
YES  
NO  
Is there 5.2VA at IC501  
Check power circuit  
Pin79, 80, 81?  
YES  
NO  
As pressing the byttons doeseach  
Replace bad switches  
function work properly?  
6 . OSD CIRCUIT  
(2 ) No F.OSD d isp la y.  
(1 ) No OSD d isp la y.  
No F.OSD display.  
No OSD display.  
YES  
YES  
Check 5.3V Line of power  
circuity.  
NO  
NO  
NO  
NO  
Refer to “(5) No OSD picture”  
Is there 5.3V IC501 Pin 51?  
YES  
Check power Vcc 9V  
YES  
NO  
Check the signal between IC301  
Pin 29 and IC501 Pin 49.  
Does video signal appear at  
IC501 Pin 50?  
Does oscillation appear at the  
IC501 PIns 37, 38?  
Replace X502.  
YES  
YES  
Check peripheral circuit and  
replace X501  
Does oscillation appear at the  
IC501 Pins 40, 41?  
Replace IC501  
YES  
NO  
Does Video signal appear at the  
IC501 Pin 47?  
Check the signal between  
IC501 Pin47 and V.out Jack.  
YES  
Replace IC501.  
3-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
BLOCK & CIRCUIT DIAGRAMS  
1 . OVERALL WIRING DIAGRAM  
3-13  
3-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
BLOCK & CIRCUIT DIAGRAMS  
2 . POWER BLOCK DIAGRAM  
3-15  
3-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
BLOCK & CIRCUIT DIAGRAMS  
3 . POWER CLRCUIT DIAGRAM  
3-17  
3-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
BLOCK & CIRCUIT DIAGRAMS  
4 . AUDIO BLOCK DIAGRAM  
3-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
BLOCK & CIRCUIT DIAGRAMS  
5 . Y/C BLOCK DIAGRAM  
3-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
BLOCK & CIRCUIT DIAGRAMS  
6 . A/V CIRCUIT DIAGRAM  
3-21  
3-22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
BLOCK & CIRCUIT DIAGRAMS  
3-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
BLOCK & CIRCUIT DIAGRAMS  
7 . SYSTEM BLOCK DIAGRAM  
3-24  
3-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
BLOCK & CIRCUIT DIAGRAMS  
3-26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
BLOCK & CIRCUIT DIAGRAMS  
8 . SYSTEM CLRCUIT DIAGRAM  
3-27  
3-28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
BLOCK & CIRCUIT DIAGRAMS  
9 . JACK CLRCUIT DIAGRAM  
3-29  
3-30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
BLOCK & CIRCUIT DIAGRAMS  
1 0 . KEY-BOARD CLRCUIT DIAGRAM  
3-31  
3-32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
PRINTED CIRCUIT DIAGRAMS  
1 . MAIN P.C.BOARD  
3-33  
3-34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION3 ELECTRICAL  
PRINTED CIRCUIT DIAGRAMS  
2 . KEY 1 P.C.BOARD  
3 . KEY 2 P.C.BOARD  
PRINTED CIRCUIT BOARD DIAGRAMS  
4 . JACK P.C.BOARD  
3-35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 4 MECHANISM  
CONTENTS  
DECK MECHANISM PARTS  
DECK MECHANISM ADJUSTMENT  
LOCATIONS  
• Top View......................................................4-1  
• Bottom View ...............................................4-1  
• Tools and Fixtures for Service ...............4-12  
1. Mechanism Alignment Position Check....4-13  
2. Preparation for Adjustment......................4-14  
3. Checking Torque .....................................4-14  
4. Guide Roller Height Adjustment..............4-15  
4-1. Preliminary Adjustment ....................4-15  
4-2. Precise Adjustment ..........................4-15  
5. Audio/Control (A/C) Head Adjustment ....4-16  
5-1. Preliminary Adjustment ....................4-16  
5-2. Confirmation of Tape Path between  
Pinch Roller and Take-up Guide......4-17  
5-3. Precise Adjustment(Azimuth Adjustment)  
.........................................................4-17  
6. X-Value Adjustment.................................4-17  
7. Adjustment after Replacing Drum Assembly  
(Video Heads) .........................................4-18  
8. Check the Tape Travel after Reassembling  
Deck Mechanism.....................................4-18  
8-1. Checking Audio and RF Locking Time  
during Playback after CUE or REV  
DECK MECHANISM  
DISASSEMBLY  
1. Drum Assembly.........................................4-2  
2. Plate Top ...................................................4-4  
3. Holder Assembly CST...............................4-4  
4. Opener Door .............................................4-4  
5. Bracket Assembly L/D Motor.....................4-4  
6. Gear Assembly Rack F/L ..........................4-4  
7. Arm Assembly F/L.....................................4-4  
8. Lever Assembly S/W.................................4-4  
9. Arm Assembly Cleaner..............................4-5  
10.Head F/E...................................................4-5  
11. Base Assembly A/C Head.........................4-5  
12.Brake Assembly T .....................................4-6  
13.Brake Assembly RS ..................................4-6  
14.Arm Assembly Tension..............................4-6  
15.Reel S / Reel T..........................................4-6  
16.Base Assembly P4 ....................................4-7  
17.Opener Lid ................................................4-7  
18.Arm Assembly Pinch .................................4-7  
19.Lever T/up / Arm T/up ...............................4-7  
20.Belt Capstan/Motor Capstan.....................4-8  
21.Lever F/R ..................................................4-8  
22.Clutch Assembly D35................................4-8  
23. Brake Assembly Capstan .........................4-8  
24.Gear Drive/Gear Cam ...............................4-9  
25.Gear Sector...............................................4-9  
26.Plate Slider................................................4-9  
27.Lever Tension............................................4-9  
28.Lever Spring..............................................4-9  
29.Gear Assembly P2/  
.........................................................4-18  
8-2. Checking for Tape Curling or  
Jamming ..........................................4-18  
MAINTENANCE/INSPECTION  
PROCEDURE  
1. Check before starting Repairs ................4-19  
2. Required Maintenance............................4-20  
3. Scheduled Maintenance..........................4-20  
4. Supplies Required for Inspection and  
Maintenance............................................4-20  
5. Maintenance Procedure..........................4-20  
5-1. Cleaning...........................................4-20  
5-2. Greasing ..........................................4-21  
Gear Assembly P3 ..................................4-10 MECHANISM TROUBLESHOOTING  
30.Base Assembly P2/  
GUIDE  
Base Assembly P3 ..................................4-10  
1. Deck Mechanism.....................................4-23  
31.Base Loading ..........................................4-11  
2. Front Loading Mechanism.......................4-26  
32.Base Tension...........................................4-11  
33.Arm Assembly Idler .................................4-11  
EXPLODED VIEWS  
1. Front Loading Mechanism Section .........4-28  
2. Moving Mechanism Section (1)...............4-29  
3. Moving Mechanism Section (2)...............4-30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM PARTS LOCATIONS  
• Top View  
Procedure  
Starting  
No.  
Fig- Vi-  
ure ew  
Part  
Fixing Type  
3 Screw  
1
2
3
4
5
Drum Assembly  
A-1  
A-2  
A-2  
A-2  
A-2  
T
T
T
T
T
Plate Top  
2 Hook  
2
2
Holder Assembly CST  
Opener Door  
Chassis Hole  
Chassis Hole  
3 Hook  
Bracket Assembly  
L/D Motor  
2,3,4  
6
7
8
9
Gear Assembly Rack F/L  
Arm Assembly F/L  
Lever Assembly S/W  
Arm Assembly Cleaner  
1 Hook, Chassis Hole A-2  
T
T
T
T
T
T
T
T
T
T
2
7
6
2,3,4,6  
Chassis Hole  
A-2  
A-2  
A-3  
A-3  
A-3  
A-4  
A-4  
A-4  
A-4  
1 Hook  
3
4
Chassis Embossing  
Chassis Embossing  
10 Head F/E  
11 Base Assembly A/C Head 1 Screw  
9
5
2,3  
2,3  
2,3  
12 Brake Assembly T  
13 Brake Assembly RS  
14 Arm Assembly Tension  
1 Hook  
1 Hook  
2 Hook  
11  
10  
1
2,3,12,13, 15 Reel S/Reel T  
14  
18  
16  
16 Base Assembly P4  
17 Opener Lid  
Chassis Embossing  
Chassis Embossing  
Shaft  
A-5  
A-5  
A-5  
A-5  
A-6  
A-6  
A-6  
A-6  
A-7  
A-7  
A-7  
T
T
T
T
B
B
B
B
B
B
B
31  
17  
19  
19  
12  
14  
15  
17  
18 Arm Assembly Pinch  
19 Lever T/Up / Arm T/Up  
17  
1 Hook  
17,18  
20 Belt Capstan/Motor Capstan 3 Screw  
21 Lever F/R  
Locking Tab  
Washer  
13  
15  
20, 21  
22 Clutch Assembly D35  
33  
8
23 Brake Assembly Capstan Locking Tab  
24 Gear Drive/Gear Cam  
25 Gear Sector  
Washer/Hook  
1 Hook  
• Bottom View  
20,21,23, 26 Plate Slider  
Shaft Guide  
24,25  
20,21,23, 27 Lever Tension  
1 Hook  
A-7  
A7  
B
B
24,25,26  
2,3,14,20, 28 Lever Spring  
Locking Tab  
30  
29  
29  
21,25,23,  
24,26  
20  
24  
25  
29 Gear Assembly P2/Gear Assembly P3 Boss  
A-8  
A-8  
B
B
23  
30  
2,3,14,25, 30 Base Assembly P2/Base Assembly P3 Chassis Slot  
29  
20  
24  
25  
32  
27  
26  
28  
2,3,14,25, 31 Base Loading  
29  
1 Screw  
A-9  
T
22  
21  
2,3,14  
32 Base Tension  
Chassis Embossing  
Locking Tab  
A-9  
A-9  
B
T
2,3,20,21, 33 Arm Assembly Idler  
22  
T:Top, B:Bottom  
NOTE : When reassembly perform the  
procedure in the reverse order.  
1) When reassembling, confirm Mechanism and Mode  
Switch Alignment Position (Refer to Page 4-13)  
2) When disassembling, the Parts for Starting No. Should  
be removed first.  
4-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM DISASSEMBLY  
Stator  
(S2)  
(S2)  
(S3)  
Drum Motor  
(S3)  
Rotor  
Drum Sub Assembly  
(Fig. A-1-1)  
(A)  
Drum FPC  
Carbon Brush  
(S1)  
(S1)  
(S1)  
H2  
H1  
Holder FPC  
Fig. A-1  
(Fig. B-1)  
1. Drum Assembly (Fig. A-1-1)  
1) Unplug the Drum FPC Connector.  
2) Remove three Screws(S1) on bottom side and separate  
the Drum assembly.  
3) Unhook (H1), (H2) and separate the Holder FPC and  
Cap FPC.  
Cap FPC  
1-1. Drum Motor  
1) Remove two Screws(S2) and disassemble the Stator of  
the Drum Motor.  
Drum FPC  
2) Remove two Screws(S3) and separate the Rotor of the  
Drum Motor from the Drum Sub assembly.  
Holder FPC  
NOTE  
When reassembling, confirm (A) portion of the Drum Sub  
assembly whether the Carbon Brush is in there or not.  
Figure in the opposite direction  
4-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM DISASSEMBLY  
Plate Top  
(Fig. A-2-1)  
(C)  
(B')  
(B)  
Holder Assembly CST  
(Fig. A-2-2)  
(E)  
(Fig. A-2-6)  
(Fig. A-2-7)  
Arm Assembly F/L  
(C1)  
Lever Assembly S/W  
(H8)  
Bracket Assembly L/D Motor  
Spring Lever S/W  
(Fig. A-2-4)  
(C')  
(E')  
(D)  
Opener Door  
(Fig. A-2-3)  
(H6)  
Chassis  
(A)  
(B)  
Gear Assembly Rack F/L  
(Fig. A-2-5)  
Fig. A-2  
4-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM DISASSEMBLY  
2) Unhook three Hooks(H3, H4, H5) on bottom side of the  
2. Plate Top (Fig. A-2-1)  
1) Pull the (B) portion of the Plate Top back in direction of  
arrow and separate the right side of it.  
Chassis, lift up the Bracket Assembly L/M and disassem-  
ble the Bracket Assembly L/D Motor.  
2) pull the (B’) portion of the Plate Top back in direction of  
arrow and separate the left side of it.  
Bracket assembly L/M  
(H4)  
(Used tools : (-) type driver, anything tool with sharp  
point or flat point.)  
(H3)  
NOTE  
(1) When reassembling, push the Plate Top after alignment  
the two position(C), (C’) as below Fig.  
(H5)  
6. Gear Assembly Rack F/L (Fig. A-2-5)  
1) Move the Gear Assembly Rack F/L in direction of  
arrow(A) and unhook the Hook(H6) pulling back in front.  
2) Separate the Gear Rack F/L in direction of arrow(B).  
(C')  
(C)  
(B')  
(B)  
NOTE  
When reassembling, align the gear part of the Gear  
Assembly Rack F/L with the Gear Drive as below Fig.  
Gear Rack F/L  
3. Holder Assembly CST (Fig.A-2-2)  
1) Move the Holder Assembly CST in direction of arrow and  
separate the left side of it first through the (D) position of  
the Chassis.  
Holder assembly CST  
Chassis  
Gear Drive  
(D)  
7. Arm Assembly F/L (Fig. A-2-6)  
1) Move the Arm Assembly F/L in direction of arrow and  
separate the left side of it first.  
2) Disassemble the Arm Assembly F/L from each guided  
hole of the Chassis.  
2) Disassemble the right side of the Holder Assembly CST  
from each guided hole of the Chassis.  
8. Lever Assembly S/W(Fig. A-2-7)  
1) Unhook the Hook(H8) in the left side of the Chassis and  
remove the Lever Assembly S/W.  
NOTE  
When reassembling, insert the (E) part of the Holder  
Assembly CST in the (E’) hole of the Chassis first and  
assemble the left side of it.  
Chassis  
4. Opener Door (Figure. A-2-3)  
1) Turn the Opener Door clockwise and remove it through  
the guide hole of the Chassis.  
(H8)  
5. Bracket Assembly L/D Motor  
(Fig. A-2-4)  
1) Unplug the Connector(C1).  
4-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM DISASSEMBLY  
Arm Assembly  
Cleaner  
(Fig. A-3-1)  
(A)  
(S4)  
Base Assembly A/C Head  
(Fig. A-3-3)  
(A)  
Head F/E  
(Fig. A-3-2)  
Chassis  
Fig. A-3  
9. Arm Assembly Cleaner (Fig. A-3-1)  
1) Breakaway the (A) portion as Fig. A-3-1 from the  
embossing of the Chassis, turn the Arm assembly  
Cleaner to clockwise direction and lift it up.  
11. Base Assembly A/C Head (Fig. A-3-3)  
1) Remove the Screw(S4) and lift the Base Assembly A/C  
Head up.  
10. Head F/E (Fig. A-3-2)  
1) Breakaway the (A) portion of the Head F/E from the  
embossing of the Chassis, turn it to counterclockwise  
direction and lift it up.  
4-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM DISASSEMBLY  
Arm Assembly Tension  
(Fig. A-4-3)  
(H11)  
Spring TB  
Brake Assembly T  
(Fig. A-4-1)  
Spring Tension  
Reel S  
Reel T  
(Fig. A-4-4)  
(Fig. A-4-4)  
Spring RS  
Brake Assembly RS  
(Fig. A-4-2)  
(H12)  
(H9)  
(H10)  
Base Tension  
Chassis  
Fig. A-4  
NOTE  
12. Brake Assembly T (Fig. A-4-1)  
1) Unhook the Spring TB from the Hook(H9) of the Chassis.  
2) Lift the Brake Assembly T up.  
Difference for Springs  
Spring TB  
Spring RS  
Spring Tension  
13. Brake Assembly RS (Fig. A-4-2)  
1) Unhook the Spring RS from the Hook(H10) of the  
Chassis.  
Color (Black)  
2) Lift the Brake Assembly T up.  
15. Reel S / Reel T (Fig. A-4-4)  
1) Difference for Reel S / Reel T  
14. Arm Assembly Tension (Fig. A-4-3)  
1) Unhook the Spring Tension from the Hook(H11) of the  
Arm Assembly Tension.  
2) Unhook the Hook(H12) of the Base Tension and lift the  
Arm Assembly Tension up.  
Reel S  
Reel T  
4-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM DISASSEMBLY  
Opener Lid  
(Fig. A-5-2)  
(B)  
(B)  
Arm  
Assembly  
Pinch  
(Fig. A-5-3)  
(C)  
Base Assembly P4  
(Fig. A-5-1)  
Lever T/up  
(Fig. A-5-4)  
(H13)  
(C)  
(H13)  
Arm T/up  
(Fig. A-5-5)  
(A)  
Chassis  
Fig. A-5  
NOTE  
16. Base Assembly P4 (Fig. A-5-1)  
1) Breakaway the (A) portion of the Base Assembly P4 from  
the embossing of the Chassis.  
When reassembling, confirm the (C) portion of the Arm  
Assembly Pinch is inserted to the Chassis hole correctly as  
Fig.  
2) Turn the Base Assembly P4 to counterclockwise direction  
and lift it up.  
19. Lever T/up (Fig. A-5-4)/  
Arm T/up (Fig. A-5-5)  
17. Opener Lid (Fig. A-5-2)  
1) Breakaway the (B) portion of the Opener Lid from the  
embossing of the Chassis.  
1) Unhook the Hook(H13) of the bottom Chassis and lift the  
Lever T/up up.  
2) Turn the Opener Lid to clockwise direction and lift it up.  
2) Lift the Arm T/up up.  
18. Arm Assembly Pinch (Fig. A-5-3)  
1) Lift the Arm Assembly Pinch up.  
4-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM DISASSEMBLY  
Belt Capstan  
(Fig. A-6-1)  
Motor Capstan  
(Fig. A-6-2)  
Washer(W1)  
Clutch Assembly D35  
(Fig. A-6-4)  
(L1)  
(L1)  
Brake Assembly Capstan  
(Fig. A-6-5)  
Lever F/R  
(Fig. A-6-3)  
(L2)  
Chassis  
(S5)  
Fig. A-6  
20. Belt Capstan (Fig. A-6-1)/  
Motor Capstan (Fig. A-6-2)  
1) Remove the Belt Capstan.  
22. Clutch Assembly D35 (Fig. A-6-4)  
1) Remove the Washer(W1) and lift the Clutch Assembly  
D35 up.  
2) Remove the three Screws(S5) on bottom Chassis and lift  
the Motor Capstan up.  
23. Brake Assembly Capstan  
(Fig. A-6-5)  
1) Pull the Locking Tab(L2) back in direction of arrow and lift  
it up.  
21. Lever F/R (Fig. A-6-3)  
1) Unlock the Locking Tab(L1) as Fig. A-6-3 and lift the  
Lever F/R up.  
4-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM DISASSEMBLY  
(H14)  
Gear Cam Hole(B)  
Gear Drive Hole(A)  
Gear Cam  
(Fig. A-7-2)  
Gear Sector  
Washer (W2)  
(Fig. A-7-3)  
Plate Slider  
Gear Drive  
(Fig. A-7-4)  
(Fig. A-7-1)  
(A)  
Lever Tension  
(Fig. A-7-5)  
Lever spring  
(L3)  
(Fig. A-7-6)  
Gear Drive Hole(C)  
Base Loading  
(H15)  
(H16)  
Chassis  
Fig. A-7  
24. Gear Drive (Fig. A-7-1)/  
Gear Cam (Fig. A-7-2)  
1) Remove the Washer(W2) and lift the Gear Drive up.  
2) Unhook the Hook(H14) of the Gear Cam and lift the Gear  
Cam up.  
26. Plate Slider (Fig. A-7-4)  
1) Just lift the Plate Slider up.  
27. Lever Tension (Fig. A-7-5)  
1) Unhook the (A) portion of the Lever Tension from the  
Hook(H16) of the Chassis.  
NOTE  
2) Turn the Lever Tension to counterclockwise direction and  
lift it up.  
When reassembling, align the Gear Drive Hole(A) and the  
Gear Cam Hole(B) in a straight line after the Gear Drive  
Hole(C) is aligned with the Chassis Hole as Fig.  
28. Lever Spring (Fig. A-7-6)  
1) Unlock the Locking Tab(L3) of the bottom Chassis and lift  
the Lever Spring up.  
25. Gear Sector (Fig. A-7-3)  
1) Unhook the Hook(H15) of the Base Loading on bottom  
Chassis and lift the Gear Sector up.  
4-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM DISASSEMBLY  
Gear Assembly P2 Hole  
Gear Assembly P3 Hole  
Gear Assembly P3  
(Fig. A-8-2)  
Gear Sector Hole(A)  
Lever Spring Boss  
Gear Assembly P2  
Plate Slider Hole(B)  
(Fig. A-8-1)  
(B)  
(A)  
Chassis  
Base Assembly P3  
(Fig. A-8-4)  
Base Assembly P2  
(Fig. A-8-3)  
Fig. A-8  
29. Gear Assembly P2 (Fig. A-8-1)/  
Gear Assembly P3 (Fig. A-8-2)  
1) Just lift the Gear Assembly P2 up.  
2) Just lift the Gear Assembly P3 up.  
30. Base Assembly P2 (Fig. A-8-3)/  
Base Assembly P3 (Fig. A-8-4)  
1) Move the Base Assembly P2 in direction of arrow(A)  
along the guide hole of the Chassis and disassemble it  
on bottom side.  
2) Move the Base Assembly P3 in direction of arrow(B)  
along the guide hole of the Chassis and disassemble it  
on bottom side.  
NOTE  
When reassembling, align the two holes of the Gear  
Assembly P2 and P3 in a straight line after confirmation  
whether the Gear Sector Hole(A) and the Plate Slider  
Hole(B) are aligned or not as Fig.  
4-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM DISASSEMBLY  
(S7)  
Base Tension  
(Fig. A-9-2)  
Base Loading  
(Fig. A-9-1)  
Arm Assembly Idler  
(Fig. A-9-3)  
(A)  
(B)  
(C)  
(D)  
Chassis  
Fig. A-9  
31. Base Loading (Fig. A-9-1)  
1) Remove the Screw(S7).  
2) Lift the Base Loading up.  
33. Arm Assembly Idler (Fig. A-9-3)  
1) Make narrower the two parts, (B) and (C), as Fig. A-9-3.  
2) Lift the Arm assembly Idler up.  
NOTE  
32. Base Tension (Fig. A-9-2)  
1) Breakaway the (A) portion of the Base Tension from the  
embossing of the Chassis.  
When disassembling, be careful not to be caught the (D) part  
by the Chassis as Fig.  
2) Turn the Base Tension to counterclockwise direction and  
lift it up.  
4-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM ADJUSTMENT  
• Tools and Fixfures for Service  
1. Cassette Torque Meter  
1. SRK-VHT-303(Not SVC part)  
1. Parts No: D00-D006  
2. Alignment Tape  
Parts No NTSC: DTN-001  
PAL:DTN-0002  
3. Torque Gauge  
3. 600g.Cm ATG  
3. Parts No:D00-D002  
V
4. Torque Gauge Adaptor  
Parts No:D09-R001  
5. Post Height Adjusting Driver  
Parts No:DTL-0005  
6. + Type Driver (ø 5)  
4-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM ADJUSTMENT  
1. Mechanism Alignment Position Check  
Purpose:To determine if the Mechanism is in the correct position, when a Tape is ejected.  
Test Conditions (Mechanism  
Test Equipment/ Fixture  
Check Point  
Condition)  
• Mechanism and Mode Switch Position  
• Blank tape  
• Eject Mode (with Cassette ejected)  
1) Turn the Power S/W on and eject the Cassette by press-  
ing the Eject Button.  
2) Remove the Top Cover and Plate Assembly Top, visual-  
ly check if the Gear Cam Hole is aligned with the  
Chassis Hole as below Fig. C-2.  
4) Remove the Screw which fixes the Deck Mechanism and  
Main Frame and confirm if the Gear Cam is aligned with  
the Gear Drive as below Fig. C-1(A).  
5) Confirm if the Mode S/W on the Main P.C.Board is  
aligned as below Fig. C-1(B).  
3) IF not, rotate the Shaft of the Loading Motor to either  
clockwise or counterclockwise until the alignment is as  
below Fig. C-2.  
6) Remount the Deck Mechanism on the Main P.C.Board  
and check each operation.  
CHECK DIAGRAM  
Mode S/W  
Gear Cam  
(B)  
(A)  
Gear Drive  
Gear Cam (o) and Gear Drive (o) groove alignment  
BOTTOM VIEW  
Fig. C-1  
L/D Motor Assembly  
Gear Cam  
(B)  
(A')  
(A)  
(B')  
Chassis Hole  
Gear Cam Hole  
Gear Drive Hole  
TOP VIEW  
Fig. C-2  
4-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM ADJUSTMENT  
cassette without tape.  
Cover the holes of the End Sensors at the both sides of  
the Chassis to prevent a light leak.  
Then the Deck Mechanism drives to the Stop Mode.  
In this case, the Deck Mechanism can accept inputs of  
each mode, however the Rewind and Review operation  
can not be performed for more than a few seconds  
because the Take-up Reel Table is in the Stop State  
and can not be detected the Reel Pulses.  
2. Preparation for Adjustment (To set the  
Deck Mechanism of the loading state  
without inserting a cassette tape).  
1) Unplug the power cord from the AC outlet.  
2) Disassemble the Top Cover and Plate Assembly Top.  
3) Plug the power cord into the AC outlet.  
4) Turn the power S/W on and push the Lever Stopper of  
the Holder Assembly CST to the back for loading the  
3. Checking Torque  
Purpose: To insure smooth transport of the tape during each mode of operation.  
If the tape transport is abnormal, then check the torque as indicated by the chart below.  
Test Conditions  
(Mechanism Condition)  
Test Equipment/ Fixture  
Checking Method  
• Torque Gauge(600g/cm ATG)  
• Torque Gauge Adaptor  
• Cassette Torque Meter  
SRK-VHT-303  
• Play (FF) or Review (REW) Mode • Perform each Deck Mechanism mode without  
inserting a cassette tape(Refer to above No.2  
Preparation for Adjustment).  
• Read the measurement of the Take-up or Supply  
Reels on the Cassette Torque Meter(Fig. C-3-2).  
• Attach the Torque Gauge Adaptor to the Torque  
Gauge and then read the value of it(Fig. C-3-1).  
Mode  
Fast Forward  
Item  
Test Equipment  
Measurement Reel  
Measurement Values  
More than 400g/cm  
More than 400g/cm  
40~100g/cm  
Fast Forward Torque  
Rewind Torque  
Cassette Torque Gauge Take-Up Reel  
Cassette Torque Gauge Supply Reel  
Cassette Torque Meter Take-Up Reel  
Cassette Torque Meter Supply Reel  
Rewind  
Play  
Play Take-Up Torque  
Review Torque  
Review  
120~210g/cm  
NOTE:  
NOTE:  
The values are measured by using a Torque Gauge and  
Torque Gauge Adaptor with the Torque Gauge affixed.  
The torque reading to measure occurs when the tape  
abruptly changes direction from Fast Forward to Rewind  
Mode, when quick braking is applied to both Reels.  
• Torque Gauge (600g.cm ATG)  
• Cassette Torque Meter (SRK-VHT-303)  
Torque Gauge  
V
Torque Gauge  
Adaptor  
Reel Table  
Fig. C-3-1  
Fig. C-3-2  
4-14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM ADJUSTMENT  
4.Guide Roller Height Adjustment  
Purpose: To regulate the height of the tape so that the bottom of the tape runs along the  
tape guide line on the Lower Drum.  
4-1. Preliminary Adjustment  
Test Equipment/ Fixture  
Test Conditions (Mechanism Condition)  
Adjustment Point  
• Post Height Adjusting Driver  
• Play or Review Mode  
• Guide Roller Height Adjustment  
screws on the Supply and Take-Up  
Guide Rollers.  
Adjustment Procedure  
ADJUSTMENT DIAGRAM  
Guide Roller Height  
Adjustment screw  
1) Confirm if the tape runs along the tape guide line of the  
Lower Drum.  
2) If the tape runs the bottom of the guide line, turn the  
Guide Roller Height Adjustment Screw to clockwise  
direction.  
3) If it runs the top, turn to counterclockwise direction.  
4) Adjust the height of the Guide Roller to be guided to the  
guide line of the Lower Drum from the starting and end-  
ing point of the Drum.  
Upper Flange  
Guide Roller  
Retaining Screw  
Fig. C-4-1  
4-2. Precise Adjustment  
Test Equipment/Fixture  
Adjustment Point  
Test Equipment Connection Points Test Conditions VCR(VCP) State  
• Oscilloscope  
• Alignment Tape  
• Post Height Adjusting  
Driver  
• Guide Roller Height  
Adjustment Screws  
• CH-1:PB RF Envelope  
• CH-2:NTSC: SW 30Hz  
PAL: SW 25Hz  
• Head Switching Output  
Point  
• Play an Alignment Tape  
Waveform Diagrams  
P2 POST  
ADJUSTMENT  
• RF Envelope Output  
Point  
Adjustment Procedure  
1) Play an Alignment Tape after connecting the probe of the  
Oscilloscope to the RF Envelope Output Test Point and  
Head Switching Output Test Point.  
2) Tracking Control(in PB Mode) : Center Position(When  
this adjustment is performed after the Drum Assembly  
has been replaced, set the Tracking Control so that the  
RF Output is Maximum).  
Turn the Roller Guide Height  
Adjustment Screw slightly  
to flatten the waveform.  
P3 POST  
ADJUSTMENT  
Fig. C-4-2  
3) Height Adjustment Screw : Flatten the RF waveform.  
(Fig. C-4-2)  
4) Turn(Move) the Tracking Control(in PB Mode) clockwise  
and counterclockwise.(Fig. C-4-3)  
5) Check that any drop of RF Output is uniform at the start  
and end of the waveform.  
Turn(Move) the Tracking  
Control to both directions  
Tracking Control at center  
Fig. C-4-3  
Connection Diagram  
NOTE  
OSCILLOSCOPE  
If the adjustment is excessive or insufficient the tape will  
jam or fold.  
RF ENVELOPE OUTPUT TEST POINT  
HEAD SWITCHING OUTPUT TEST  
POINT  
4-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM ADJUSTMENT  
5. Audio/Control (A/C) Head Adjustment  
Purpose: To insure that the tape passes accurately over the Audio and Control Tracks in  
exact alignment of the both Record and Playback Modes.  
5-1. Preliminary Adjustment (Height and Tilt Adjustment)  
Perform the Preliminary Adjustment, when there is no Audio Output Signal with the Alignment Tape.  
Test Equipment/ Fixture  
Test Conditions (Mechanism Condition)  
Adjustment Point  
• Blank Tape  
• Tilt Adjustment Screw(C)  
• Screw Driver(+) Type 5mm  
• Height Adjustment Screw(B)  
• Azimuth Adjustment Screw(A)  
• Play the blank tape  
Adjustment Procedure/Diagrams  
1) Initially adjust the Base Assembly A/C Head as shown  
Fig. C-5-1 by using the Height Adjustment Screw(B).  
2) Play a blank tape and observe if the tape passes accu-  
rately over the A/C Head without tape curling or folding.  
3) If folding or curling is occured then adjust the Tilt  
Adjustment Screw(C) while the tape is running to resem-  
ble Fig. C-5-3.  
4) Reconfirm the tape path after Playback about 4~5 sec-  
onds.  
NOTE  
Ideal A/C head height occurs when the tape runs between  
0.2~0.25mm above the bottom edge of the A/C Head core.  
Tape  
A/C Head  
P4  
Tape  
0.2~0.25mm  
A/C Head Base  
Fig. C-5-1  
Fig. C-5-3  
X-Value Adjustment  
Hole  
Fixed Screw  
Azimuth Adjustment  
Screw(A)  
Tilt Adjustment  
Screw(C)  
Height Adjustment  
Screw(B)  
A/C Head Assembly  
Fig. C-5-2  
4-16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM ADJUSTMENT  
(2) If folding or curling is observed at the top of it then  
slowly turn the Tilt Adjustment Screw(C) in the  
counterclockwise direction.  
5-2. Confirm that the tape passes smoothly  
between the Take-up Guide and Pinch  
Roller(using a mirror or the naked eye).  
1) After completing Step 5-1.(Preliminary Adjustment), check  
NOTE:  
that the tape passes around the Take-up Guide and Pinch  
Roller without folding or curling at the top or bottom.  
(1) If folding or curling is observed at the bottom of the  
Take-up Guide then slowly turn the Tilt Adjustment  
Screw(C) in the clockwise direction.  
Check the RF envelope after adjusting the A/C Head, if the  
RF waveform differs from Fig. C-5-4, performs Precise  
Adjustment to flat the RF waveform.  
5-3. Precise Adjustment (Azimuth adjustment)  
Test Conditions  
Test Equipment/ Fixture  
Connection Point  
• Audio output jack  
Adjustment Point  
(Mechanism Condition)  
• Oscilloscope  
• Alignment Tape(SP)  
• Screw Driver(+) Type 5mm  
• Play an Alignment Tape  
1KHz, 7KHz Sections  
• Azimuth Adjustment Screw(A)  
• Height Adjustment Screw(B)  
Adjustment Procedure  
1KHZ  
7KHZ  
1) Connect the probe of the oscilloscope to Audio Output  
Jack.  
2) Alternately adjust the Azimuth Adjustment Screw(A) and  
the Tilt Adjustment Screw(C) for maximum output of the  
1KHz and 7KHz segments, while maintaining the flattest  
envelope differential between the two frequencies.  
A:Maximum  
B:Maximum  
Fig. C-5-4  
6. X-Value Adjustment  
Purpose: To obtain compatibility with the other VCR(VCP) Models.  
Test Conditions  
(Mechanism Condition)  
Test Equipment/ Fixture  
Connection Point  
Adjustment Point  
• Play an Alignment Tape  
• CH-1: PB RF Envelope  
• CH-2: NTSC: SW 30Hz  
PAL: SW 25Hz  
• Oscilloscope  
• Alignment Tape(SP only)  
• Screw Driver(+) Type 5mm  
Groove at the  
Base A/C  
Left  
• Head Switching Output  
Test Point  
• RF Envelope Output Test  
Point  
Right  
Adjustment Procedure  
Adjustment Diagram  
X-Value Adjustment Hole  
1) Release the Automatic Tracking to run long enough for  
tracking to complete it’s cycle.  
2) Loosen the Fixed Mounting Screw and move the Base  
Assembly A/C Head in the direction as shown in the dia-  
gram to find the center of the peak that allows for the max-  
imum waveform envelope.  
Fixed Screw  
Azimuth Adjustment  
Screw(A)  
Tilt Adjustment Screw(C)  
Height Adjustment Screw(B)  
This method should allow the 31µm Head to be centrally  
located over the 58µm tape track.  
3) Tighten the Base Assembly A/C Head mounting Screw.  
OSCILLOSCOPE  
Connection Diagram  
RF ENVELOPE OUTPUT TEST POINT  
CH-1 CH-2  
HEAD SWITCHING OUTPUT TEST POINT  
4-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DECK MECHANISM ADJUSTMENT  
7. Adjustment after Replacing Drum Assembly (Video Heads)  
Purpose: To correct for shift in the Roller Guide and X value after replacing the Drum.  
Test Conditions  
Test Equipment/ Fixture  
Connection Point  
Adjustment Points  
(Mechanism Condition)  
• CH-1: PB RF Envelope  
• CH-2: NTSC: SW 30Hz  
PAL: SW 25Hz  
• Head Switching Output  
Test Point  
• Guide Roller Precise  
Adjustment  
• Switching Point  
• Tracking Preset  
• X-Value  
• Oscilloscope  
• Alignment Tapes  
• Blank Tape  
• Post Height Adjusting Driver  
• Screw Driver(+) Type 5mm  
• Play the Blank Tape  
• Play an Alignment Tape  
• RF Envelope Output Test Point  
Checking/Adjustment Procedure  
OSCILLOSCOPE  
Connection Diagram  
Play a blank tape and check for tape curling or creasing around  
the Roller Guide. If there is a problem then follow the procedure  
4. "Guide Roller Height" and 5. "Audio Control(A/C) Head  
Adjustment".  
RF ENVELOPE OUTPUT TEST POINT  
CH1 CH2  
HEAD SWITCHING OUTPUT TEST  
POINT  
Waveform  
V1/V MAX E 0.7  
V1  
V
V2  
V2/V MAX E 0.8  
RF ENVELOPE OUTPUT  
Fig. C-7  
8. Check the Tape Travel after Reassembling Deck Assembly.  
8-1. Checking Audio and RF Locking Time during playback and after CUE or REV (FF/REW)  
Test Equipment  
Test Conditions  
(Mechanism Condition)  
Specification  
Connection Points  
Connection Points  
Test Equipment/ Fixture  
• RF Locking Time: Less than 5  
sec.  
• Audio Locking Time:Less than  
10sec  
• Oscilloscope  
• CH-1: PB RF Envelope  
• CH-2: Audio Output  
• RF Envelope Output Point  
• Audio Output Jack  
• Play an Alignment Tape  
(with 6H 3kHz Color Bar  
Signal)  
• Alignment Tapes(with 6H  
3KHz Color Bar Signal)  
• Stop Watch  
Checking Procedure  
NOTES:  
Play an Alignment Tape then change the operating mode to  
CUE or REV and confirm if the unit meets the above listed  
specifications.  
1) CUE is the forward search mode  
2) REV is the backward search mode  
3) Refer to the Play mede  
8-2. Checking for tape curling or jamming  
Test Equipment/ Fixture  
• T-160 Tape  
Specification  
Test Conditi  
V
o
C
n
R
s
(
(
V
M
C
e
P
ch  
)
a
S
n
t
i
a
s
t
m
e
Condition)  
• Be sure there is no tape jamming or curling at  
the begining, middle or end of the tape.  
•
Run the CUE, REV, Play mode at the  
beginning and the end of the tape.  
• T-120 Tape  
Checking Procedure  
1) Confirm that the tape runs smoothly around the roller  
guides, Drum and A/C Head Assemblies while abruptly  
changing operating modes from Play to CUE or REV.  
This is to be checked at the begining, middle and end  
sections of the tape.  
2) Confirm that the tape passes over the A/C Head  
Assembly as indicated by proper audio reproduction and  
proper tape counter performance.  
4-18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE/INSPECTION PROCEDURE  
1. Check before starting repairs  
The following faults can be remedied by cleaning and oil-  
ing. Check the needed lubrication and the conditions of  
cleanliness in the unit.  
Check with the customer to find out how often the unit is  
used, and then determine that the unit is ready for inspec-  
tion and maintenance. Check the following parts.  
Replace-  
ment  
Phenomenon  
Color beats  
Inspection  
F/E Head  
Dirt on Full-Erase Head  
Dirt on Video Head  
o
Poor S/N, no color  
o
Video Head  
Vertical or  
Horizontal jitter  
Dirt on Video Head  
Dirt on tape transport system  
o
o
o
o
Fig. C-9-1 Top View  
A/C Head  
Low volume,  
Sound distorted  
Dirt on Audio/Control Head  
Dirt on Pinch Roller  
Pinch Roller  
Belt Capston  
Tape does not run.  
Tape is slack  
Clutch  
Assembly D35  
In Review and  
Unloading (off mode),  
the tape is rolled up  
loosely.  
Clutch Assembly D35  
torque reduced  
Cleaning Drum and  
transport system  
Fig. C-9-3  
NOTE  
If locations marked with o do not operate normally after  
cleaning, check for wear and replace.  
See the EXPLODED VIEWS at the end of this manual as  
well as the above illustrations and see the Greasing (Page  
4-21, 22) for the sections to be lubricated and greased.  
Fig. C-9-2 Bottom View  
* No. (1)~(12) Indicates the Tape Path to be traveled from Supply Reel to Take-up Reel.  
(6) Base Assembly P3  
(3) F/E Head  
(7) A/C Head  
(8) P4 Post  
(5) Drum Assembly  
(Video Head)  
(10) Pinch Roller  
(11) Take-up Guide Post  
(4) Base  
Assembly P2  
(2) Tension Post  
(9) Capstan Shaft  
(12) Take-up Reel  
(1) Supply Reel  
Fig. C-9-3 Tape Transport System  
4-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE/INSPECTION PROCEDURE  
2. Required Maintenance  
4. Supplies Required for Inspection and  
Maintence  
The recording density of a VCR(VCP) is much higher than  
that of an audio tape recorder. VCR(VCP) components must  
be very precise, at tolerances of 1/1000mm, to ensure com-  
patibility with the other VCRs. If any of these components are  
worn or dirty, the symptoms will be the same as if the part is  
defective. To ensure a good picture, periodic inspection and  
maintenance, including replacement of worn out parts and  
lubrication, is necessary.  
(1) Grease : Kanto G-311G (Blue) or equivalent  
(2) Isopropyl Alcohol or equivalent  
(3) Cleaning Patches  
(4) Grease : Kanto G-381(Yellow)  
5. Maintenance Procedure  
5-1) Cleaning  
3. Scheduled Maintenance  
(1) Cleaning video head  
First use a cleaning tape. If the dirt on the head is too  
stubborn to remove by tape, use the cleaning patch. Coat  
the cleaning patch with Isopropyl Alcohol. Touch the  
cleaning patch to the head tip and gently turn the  
head(rotating cylinder) right and left.  
(Do not move the cleaning patch vertically. Make sure  
that only the buckskin on the cleaning patch comes into  
contact with the head. Otherwise, the head may be dam-  
aged.)  
Schedules for maintenance and inspection are not fixed  
because they vary greatly according to the way in which the  
customer uses the VCR(VCP), and the environment in which  
the VCR(VCP) is used.  
But, in general home use, a good picture will be maintained  
if inspection and maintenance is made every 1,000 hours.  
The table below shows the relation between time used and  
inspection period.  
Table 1  
Thoroughly dry the head. Then run the test tape. If lso-  
propyl Alcohol remains on the video head, the tape may  
be damaged when it comes into contact with the head  
surface.  
When  
inspection is  
About 1  
year  
About 3  
years  
About 18  
months  
necessary  
(2) Clean the tape transport system and drive system, etc, by  
wiping with a cleaning patch wetted with Isopropyl  
Alcohol.  
Average  
hours used  
per day  
One hour  
NOTES:  
1
It is the tape transport system which comes into contact  
with the running tape. The drive system consists of those  
parts which moves the tape.  
Two hours  
2
Make sure that during cleaning you do not touch the tape  
transport system with excessive force that would cause  
deformation or damage to the system.  
Three hours  
Drum  
(Rotating Cylinder)  
Cleaning Patch  
Head Tip  
Touch this section of cleaning  
patch to the head tip and gently  
turn the Drum (Rotating Cylinder)  
Coat With Isopropyl Alcohol  
Fig. C-9-4  
4-20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE/INSPECTION PROCEDURE  
(2) Periodic greasing  
5-2) Greasing  
Grease specified locations every 5,000 hours.  
(1) Greasing guidelines  
1) Loading Path Inside & Top side  
2) Base Assembly P2,P3 stopper  
3) Shaft  
4) Shaft  
5) Clutch Assembly D35 Shaft  
6) Plate Slider Guide Sections  
Apply grease, with a cleaning patch. Do not use exces-  
sive grease. It may come into contact with the tape  
transport or drive system. Wipe excessive grease and  
clean with cleaning patch wetted in Isopropyl Alcohol.  
7) Plate Slider Guide Sections  
8) Gear Assembly P2, P2 Rubbing  
Sections  
NOTE:Greasing Points  
2
1) Loading Path Inside & Top side  
2) Base Assembly P2, P3 stopper  
3) Shaft  
5) Arm Take-up Rubbing Sections  
6)Reel S,T shaft(G381:Yellow)  
7) Arm Assembly F/L Rotating  
Sections  
4) L/D Motor Gear Wheel Part  
1
8
2
3
4
3
1
4
5
7
6
Slider Guide  
5
Slider Guide  
Chassis (Bottom)  
7
7
6
Chassis (Top)  
Gear Part  
Gear Cam  
Gear Sector  
Gear Rack F/L  
Base Loading  
Gear Drive  
Guide Rail  
Chassis (Right Side)  
Plate Slider  
Chassis (Left Side)  
4-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE/INSPECTION PROCEDURE  
Lever, F/R, Base, Tension  
GEAR AY, P2 & P3  
Boss  
Cam  
Lever, F/R  
Base, Tension  
Clutch  
(G-754. Yellow)  
Arm Tension  
Guide Hole  
4-22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MECHANISM TROUBLESHOOTING GUIDE  
1.Deck Mechanism  
A.  
Auto REW doesn't work.  
YES  
Is the output of END sensor of  
supply side "H"?  
“H”: more than 3.5V  
“L”: less than 0.7V~1V  
NO  
YES  
NO  
Is the Vcc. voltage of End  
sensor 5V?  
Check the syscon power.  
YES  
Replace the End sensor.  
NO  
Is the voltage across IR LED  
Replace the IR LED.  
between 0.8~1.5V?  
YES  
Check the syscon circuit.  
B.  
No F/R modes.  
YES  
NO  
Is the mode SW assembled  
correctly? (refer to page 4-13.)  
Is the present mode  
F/R Mode?  
YES  
NO  
Is the normal voltage supplied to  
the Capstan Motor Vcc1, Vcc2?  
Does the Capstan Motor rotate?  
YES  
YES  
NO  
Does terminal voltage(Vctl) of  
Capstan Motor supply side more  
than 4V?  
Do the T/Up, Supply Reel  
rotate?  
Check the servo, power  
circuits.  
YES  
YES  
Replace the Capstan Motor.  
Check the syscon circuit.  
4-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MECHANISM TROUBLESHOOTING GUIDE  
C.  
AUTO STOP.  
(PLAY/CUE/REV)  
Check alignment positions  
(page 4-13).  
NO  
In Play/Cue/Rev, Is the Pinch  
Roller in contact with the  
Is the output of DFG, DPG OK?  
Capstan Shaft?  
Replace the Drum Motor.  
NO  
YES  
YES  
NO  
Are there T/up and Supply Reel  
pulses.  
Check the Servo, Syscon.  
YES  
Check the Syscon, µ-COM.  
Replace the Reel Sensor.  
D.  
Cassette doesn’t load.  
Insert the cassette.  
YES  
NO  
NO  
Does the Lever Assembly S/W  
work normally?  
Check Lever Assembly S/W.  
YES  
Is there variation for CST IN S/W  
Output?  
NO  
Does the CST IN S/W work  
normally?  
(In Tape with REC Tab  
Replace the CST IN S/W.  
“L”→“H”→“L”)  
(In Tape without REC Tab  
“L”→“H”→“L”→“H”)  
YES  
YES  
NO  
Check the Syscon Circuit.  
Check the Syscon Circuit.  
4-24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MECHANISM TROUBLESHOOTING GUIDE  
E.  
In PB mode Tape Presence  
not sensed.  
NO  
Is the Pinch Roller attached  
to the Capstan Motor Shaft?  
Check Alignment positions  
(page 4-13).  
YES  
NO  
NO  
Does the T/Up Reel turn?  
Is the Belt ok?  
Replace the Belt.  
YES  
YES  
Check the Clutch and Idler  
Assembly.  
Does the Capstan Motor turn?  
YES  
NO  
Is the voltage supplied to the  
Capstan Motor Vcc1,Vcc2 each?  
Does the Drum Motor turn?  
YES  
YES  
NO  
Is the terminal voltage(vctl) of  
Capstan Motor supplied more  
than 4V?  
Are there DPG, DFG pulses?  
Check the Servo, Power.  
YES  
YES  
Are the T/Up and Supply Reel  
Sensors ok?  
Replace the Capstan Motor.  
YES  
NO  
NO  
NO  
Is the Vcc voltage of the Drum  
Motor normal?  
Check the Servo, Syscon.  
Check the Syscon, Circuit.  
Check the Syscon, Circuit.  
YES  
Is the terminal voltage(vctl) of the  
Drum Motor more than 4V?  
YES  
Replace the  
Drum Motor.  
4-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MECHANISM TROUBLESHOOTING GUIDE  
2. Front Loading Mechanism  
A.  
Cassette cannot be inserted.  
NO  
NO  
NO  
Does the Lever Assembly  
Switch work?  
Is the Lever Assembly Switch  
Spring damaged or omitted?  
Replace or add the Lever  
Assembly Switch Spring.  
YES  
YES  
Does the CST IN Switch work  
normally?  
Replace the CST IN Switch.  
YES  
Is the Vcc of Main P.C.Board  
5V?  
Check the syscon circuit.  
NO  
YES  
Is the voltage between cassette  
switch and GND on Main  
P.C.Board 5V??  
Check the power circuit.  
NO  
YES  
Check the Mode switch location  
and syscon circuit.  
Is there a short circuit between cassette  
switch and GND on main P.C.Board?  
NO  
YES  
Remove the short circuit part or  
Replace the main P.C.Board.  
Replace the CST IN Switch.  
B.  
Cassette does not eject.  
NO  
Does the L/D Motor rotate in reverse?  
Check the L/D Motor or Drive IC.  
Replace the Lever Assembly Switch.  
Replace the Arm Assembly F/L.  
YES  
NO  
NO  
Does the Lever Assembly Switch work?  
YES  
Does the Arm Assembly F/L work normally?  
YES  
NO  
Does the Opener Door work?  
Replace the Opener Door.  
4-26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MECHANISM TROUBLESHOOTING GUIDE  
C.  
Cassette does not load.  
Does the cassette insert?  
YES  
Does the Opener Lid work?  
NO  
YES  
Does the Gear Assembly Rack F/L  
work?  
Replace the Opener Lid.  
NO  
YES  
Replace the Gear Rack F/L.  
Does the Opener Door work?  
NO  
YES  
Check the opener Door assembled  
correctly.  
Does the Arm Assembly F/L work?  
NO  
YES  
Does the L/D Motor work?  
Replace the Arm Assembly F/L.  
Check the power of L/D Motor.  
NO  
YES  
Does the Holder Assembly Cassette  
move the Arm Assembly F/L?  
NO  
YES  
Replace the Front Loading  
Mechanism Assembly.  
Check the Holder Assembly Cassette  
assembled correctly.  
4-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXPLODED VIEWS  
1. Front Loading Mechanism Section  
4-28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXPLODED VIEWS  
2. Moving Mechanism Section(1)  
OPTIONAL PART  
4-29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXPLODED VIEWS  
3. Moving Mechanism Section(2)  
OPTIONAL PART  
4-30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SECTION 5. REPLACEMENT PARTS LIST  
NOTE: Warning  
Parts that are shaded are critical With respect  
to risk of fire or electrical shock.  
MODEL : NTH960N  
NSP : Not Service Part  
MECHANICAL SECTION  
RUN DATE : 2004.05.01  
S
AL LOCA.NO PART NO.  
DESCRIPTION  
ASSEMBLY PARTS SECTION  
DECK ASSEMBLY,VIDEO  
DRUM(CIRC) ASSEMBLY  
BRACKET ASSEMBLY  
GEAR ASSY  
GEAR ASSY  
HOLDER ASSY  
GEAR ASSY  
ARM ASSY  
LEVER  
SPECIFICATION  
REMARKS  
A00  
A01  
A04  
A11  
A12  
A21  
A22  
A23  
A24  
6721R-0771U  
6723R-D402G  
4811R-0038B  
4471R-0005A  
4471R-0004A  
4931R-0047A  
4471R-0006A  
4261R-0023A  
4510R-0046A  
DECK/MECHA D35 LG T/L (4HD(ALL  
DECK/MECHA (8N4T) D35-4CH NTSC  
L/D  
P3  
P2  
CST  
RACK F/L  
F/L  
ASSY SWITCH  
PARTS SECTION  
DRUM(CIRC) ASSEMBLY  
MOTOR(MECH)  
BRUSH,CARBON  
HOLDER  
CAP  
CABLE,FLAT  
ARM  
ARM ASSY  
BASE ASSY  
BASE ASSY  
BASE ASSY  
OPENER  
BASE ASSEMBLY  
REEL  
SPRING  
BRAKE ASSEMBLY  
SPRING  
BRAKE ASSY  
HEAD(CIRC)  
BASE  
ARM ASSEMBLY  
BRACKET  
MOTOR(MECH)  
GEAR  
REEL  
ARM ASSEMBLY  
LEVER  
SPRING  
CHASSIS ASSEMBLY  
BELT  
MOTOR(MECH)  
SUPPORTER  
GEAR  
SPRING  
GEAR  
GEAR  
BRAKE ASSY  
LEVER  
CLUTCH ASSEMBLY  
GEAR  
ARM ASSY  
SPRING  
GEAR  
GEAR  
SPRING  
ARM ASSY  
LEVER  
001  
002  
002A  
003  
004  
008  
009  
011  
012  
013  
014  
015  
016  
017  
018  
019  
020  
021  
022  
023  
024  
025  
026  
027  
028  
029  
030  
031  
032  
051  
052  
052A  
054  
054A  
055  
056  
058  
060  
061  
064  
065  
066  
067  
068  
069  
070  
076  
077  
078  
6723R-D305G  
4680R-B008A  
5202R00002C  
4930R-0285A  
5006R-0034A  
6850R-HG18Z  
4260R-0038A  
4261R-0022A  
3041R-0037A  
3041R-0038A  
3041R-0039A  
5870R-0005A  
3041R-0036A  
4408R-0003A  
4970R-0140A  
4421R-0008A  
4970R-0128A  
4421R-0006A  
6520D00002A  
3040R-0057A  
4261R-0024A  
4810R-0111A  
4680R-D006A  
4470R-0093A  
4408R-0004A  
4261R-0019E  
4510R-0043A  
4970R-0123A  
3141R-0040A  
4400R-0005A  
4680R-A012B  
4980R-0023A  
4470R-0100A  
4970R-0124B  
4470R-0097A  
4470R-0096A  
4421R-0007A  
4510R-0040A  
4265R-0005A  
4470R-0098A  
4261R-0021A  
4970R-0122A  
4470R-0095A  
4470R-0094A  
4970R-0122A  
4261R-0020A  
4510R-0047A  
3300R-M116A  
4510R-0041A  
DECK/MECHA SUB D35-4CH NT (8N4  
DRUM VH4302-800 SANYO FOR D35K  
ASSY D33 (TIP+2 SPRING) 1.4,  
FPCB(4CH)  
FPC  
P=1.25 FFC UL2896(0.05X0.8) 7  
T/UP(D35)  
TENSION(D35)  
P2  
P3  
P4  
LID(D35)  
A/C HEAD (ALPS)  
S
COIL RS D35  
RS  
COIL D35 (TB)  
T
D35 FE ST FE HEAD  
LOADING  
IDLER (H)  
L/D  
LOADING RF-370CA-12560 MABUCHI  
DECK/MECHA WHEEL OTHER  
T
DECK/MECHA PINCH  
T/UP  
COIL TENSION(D35)  
D35  
CAPSTAN  
CAPSTAN MCVC-035TB LGIT FOR T/  
CAPSTAN(D35)  
RACK F/L  
COIL D35 (RACK F/L)  
DRIVE(D35)  
CAM(D35)  
CAPSTAN  
F/R(D35)  
D35 (M)  
SECTOR(D35)  
P3  
COIL D35  
P3  
P2  
COIL D35  
P2  
SPRING  
SLIDER  
PLATE  
LEVER  
TENSION  
- 5-1 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MODEL : NTH960  
RUN DATE : 2004.05.01  
S
AL LOCA.NO PART NO.  
DESCRIPTION  
SPECIFICATION  
TENSION(D35)  
TOP  
COIL D35 (STOPPER)  
SIDE(L)  
CST  
SIDE(R)  
STOPPER  
DOOR  
F/L(L)  
REMARKS  
079  
100  
102  
103  
105  
106  
107  
109  
110  
112  
113  
114  
115  
116  
117  
116  
117  
3040R-0056A  
3301R-M022A  
4970R-0130A  
4930R-0276A  
4930R-0274A  
4930R-0275A  
4510R-0044A  
5870R-0004A  
4260R-0035A  
3070R-0002A  
4970R-0127A  
4260R-0036A  
4510R-0042A  
4970R-0138A  
3300R-M137A  
4970R-0138A  
3300R-M137A  
BASE  
PLATE ASSEMBLY  
SPRING  
HOLDER  
HOLDER  
HOLDER  
LEVER  
OPENER  
ARM  
BODY  
SPRING  
ARM  
LEVER  
SPRING  
PLATE  
SPRING  
PLATE  
F/L  
COIL D35 (F/L(R))  
F/L(R)  
SWITCH  
COIL D35 SWITCH  
SPRING CST  
COIL D35 SWITCH  
SPRING CST  
NSP  
SCREW  
402  
405  
406  
409  
410  
452  
517  
518  
1MPC0261418  
1SZZR-0031B  
1MEC0302018  
1SZZR-0032B  
1APF0262218  
353-051A  
SCREW MACHINE,PAN HEAD  
SCREW,DRAWING  
PAN HEAD MACHINE SCREW S/W +  
SCREW,DRAWING  
SCREW TAP TITE(B),PAN HEAD  
SCREW,DRAWING  
WASHER,DRAWING  
WASHER,DRAWING  
D 2.6 L 4.0 MSWR3/FZY  
+ 1 D2.6 L5.8 SWRCH16A/FZY TAP  
D 3.0 L 6.0 MSWR3/FZY  
+ 1 D2.6 L5.0 SWRCH18A/FZY TAP  
#NAME?  
SPECIAL  
STOPPER  
1WZZR-0004D  
1WZZR-0004A  
STOPPER  
Cabinet & Main Frame Section  
S
AL LOCA.NO.  
PART NO  
DESCRIPTION  
SPECIFICATION  
REMARKS  
ASSEMBLY SECTION  
DECK ASSEMBLY,VIDEO  
PWB(PCB) ASSEMBLY,C/SKD  
PANEL ASSEMBLY,FRONT  
FRAME ASSEMBLY  
A00  
A42  
A43  
A44  
A45  
6721R-0771U  
6871RK5700K  
05503807  
3211RKS008B  
3501RK3200B  
DECK/MECHA D35 LG T/L (4HD(ALL  
SNILN4T3526  
NTH960 C-TYPE  
VCR MAIN(S008B) + PACKING  
CCD TL-AT230  
BOARD ASSEMBLY  
PARTS SECTION  
CASE  
FRAME  
KNOB  
KNOB  
PANEL,VIDEO  
MAGNET  
DOOR  
SPRING  
KNOB  
KNOB  
POWER CORD  
PANEL  
CASE ASSY  
HOLDER ASSEMBLY  
COVER  
250  
260  
277  
278  
280  
281  
283  
284  
285  
286  
300  
320  
323  
325  
330  
3110R-S040F  
3210R-0023A  
4940R-Z075A  
4940R-Z076B  
3720R-F721D  
524-013A  
LV-TL1960 2960 MOLD AIRHALL BA  
VCR - MAIN  
SHUTTLE(TL-AR30M)  
CCD TL-AT130 MOLD  
CCD LV-TL1960 S MOLD HIPS 40AF  
VCR - ASSY DOOR  
HRV30C  
DOOR  
CCD LV-TL124 MOLD  
SLIDE (LV-TL24)  
IT10S2(6A/250V) VOLEX IMMETRO  
NTH960C  
PRE-AMP (PBSB-SH)  
LCD PWB(ABS XR-401))  
BOTTOM(LARGE)  
50502527  
442-681A  
4940R-Z086A  
4940R-S017A  
6410RZHV01A  
50502166  
3111R-0089B  
4930R-0190B  
3550R-0210A  
SCREW  
452  
457  
462  
353-051A  
353-051E  
353-136A  
SCREW,DRAWING  
SCREW,DRAWING  
SCREW,DRAWING  
SPECIAL  
SPECIAL (3X12)  
SPECIAL(FBK) (353S353A)  
Packing & Accessory Section  
S
AL LOCA.NO.  
PART NO  
DESCRIPTION  
SPECIFICATION  
REMARKS  
801  
802  
803  
804  
808  
900  
3835RS0069N  
3890R-C065KBOX,MASTER  
3920R-E016A  
3858R-S001A  
534-008C  
INSTRUCTION ASSEMBLY  
CCD TL-AT230M-AABBDL1_ENG_POR_  
TL-AT130M  
AABBDL  
.
1
PACKING  
SHEET (MECH)  
BATTERY,MANGANESE  
REMOTE CONTROLLER ASSEMBLY  
Packing LV-TL24I 0.02 0 EPS 10  
Packing LDPE 600M 630MM 0.5 VC  
AAAM(R03) SEOTONG 1-5 V - 1PA  
P9 LV-TL1960  
6711R1P041H  
- 5-2 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MODEL : NTH960  
RUN DATE : 2004.05.01  
Electrecal section  
S
AL LOCA.NO.  
PART NO  
DESCRIPTION  
SPECIFICATION  
REMARK  
BATTERY,LITHIUM  
RB500  
534-059AAAA  
BATTERY,LITHIUM  
LR6A-2S/ MATUSHITA - - LITHUM  
BUZZER  
BZ501  
RL301  
6908RB0001A  
6920R-B201A  
BUZZER  
BUZZER  
PKM24SP-3801 PKM24SP-3801 MURA  
UT205-5SC YUYU AC 250 V 5-0 A  
CAPACITOR  
C101  
C102  
C103  
C105  
C106  
C109  
C111  
C112  
C113  
C114  
C116  
C117  
C118  
C119  
C120  
C121  
C123  
C128  
C152  
C153  
C154  
C155  
C170  
C172  
C173  
C301  
C302  
C303  
C304  
C305  
C306  
C307  
C308  
C309  
C310  
C311  
C312  
C313  
C314  
C315  
C316  
C317  
C318  
C319  
C322  
C323  
C324  
C325  
C326  
C327  
C328  
C329  
C330  
C331  
624-088F  
624-088F  
624-082C  
0CQ1031Y519  
624-087A  
CAPACITOR,DRAWING  
CAPACITOR,DRAWING  
CAPACITOR,AL.ELECTROLYTIC  
CAPACITOR,FIXED FILM  
CAPACITOR  
PCX2 275V 0.1UF,M (PILKO)  
PCX2 275V 0.1UF,M (PILKO)  
100MF/400V SHL SMPS S/Y  
0.01UF D 630V 10% PE NI TP5  
HIGH-VOL 150P/1KV SMPS NEW-KOR  
CE 47UF/50V KME (SMPS)  
0.022UF 50V Z F TA26 S  
3300 PF 400V M E R(NK,AD,SD)  
330PF D 400V 10% B(Y5P) R  
0.047UF S 50V 5% PE TP5  
1000UF KME 16V M FM5 BULK  
CE 1000UF/10V SHL(10*12.5)T/P  
220M SMS 10V M FM5 TP(5)  
CE 47UF/50V KME (SMPS)  
470UF KME TYPE 25V M FM5 BULK  
CE 470UF/25V SHL(10*12.5)T/P  
330UF KME TYPE 35V 20% FL BULK  
0.022UF 50V Z F TA26 S  
10M SRA 16V M FM5 TP(5)  
10M SRA 16V M FM5 TP(5)  
10M SRA 16V M FM5 TP(5)  
4.7UF SRA,SS 50V 20% FM5 TP 5  
0.1M SRA 50V M FM5 TP(5)  
0.1UF D 50V 80%,-20% F(Y5V) TA  
47UF SRA,SS 35V M FM5 TP 5  
0.1UF D 50V 80%,-20% F(Y5V) TA  
0.01M 16V M Y TA26  
1.0M SRA/SS50V M FM5 TP(5)  
220M SRA 6.3V M FM5 TP(5)  
0.1UF D 50V 80%,-20% F(Y5V) TA  
0.01M 16V M Y TA26  
27P 50V J SL TA26  
33P 50V J SL TA26  
330P 50V K B TA26  
4.7UF SRA,SS 50V 20% FM5 TP 5  
180P 50V K B TA26  
22P 50V J SL TP26  
100PF 50V J B TA26  
624-085D  
CAPACITOR  
0CN223AK948  
0CG3320U630  
0CG3310U510  
0CQ4732K409  
0CE108BF630  
624-082H  
0CE2276D638  
624-085D  
0CE477BH630  
624-082G  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,SEMI CERAMIC  
CAPACITOR,FIXED CERAMIC(TEMP.C  
CAPACITOR,FIXED FILM  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR  
CAPACITOR,AL.ELECTROLYTIC  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,AL.ELECTROLYTIC  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(T.C)  
0CE337BJ610  
0CN223AK948  
0CE1064F638  
0CE1064F638  
0CE1064F638  
0CE4754K638  
0CE1044K638  
0CN1040K948  
0CE4764J638  
0CN1040K948  
0CN1030F678  
0CE1054K638  
0CE2274C638  
0CN1040K948  
0CN1030F678  
0CX2700K408  
0CX3300K408  
0CN3310K518  
0CE4754K638  
0CN1810K518  
0CX2200K408  
0CN1010K418  
0CN1020K518  
0CE1063F638  
0CE1063F638  
0CN1030F678  
0CE2254K638  
0CN1040K948  
0CE4764F638  
0CE4764F638  
0CN1040K948  
0CN1050K948  
0CE1063F638  
0CE1063F638  
0CN223AK948  
0CN223AK948  
0CN1030F678  
0CE2274C638  
CAPACITOR TUBULA(T.C)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,FIXED TUBULAR(High d  
CAPACITOR TUBULA(T.C)  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,AL.ELECTROLYTIC  
CAPACITOR,AL.ELECTROLYTIC  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,AL.ELECTROLYTIC  
CAPACITOR,AL.ELECTROLYTIC  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,ELECTROLYTIC  
1000P 50V K B TA26  
10M SRE/SE 16V M FM5 TP(5)  
10M SRE/SE 16V M FM5 TP(5)  
0.01M 16V M Y TA26  
2.2UF SRA,SS 50V 20% FM5 TP 5  
0.1UF D 50V 80%,-20% F(Y5V) TA  
47M SRA/SS 16V M FM5 TP(5)  
47M SRA/SS 16V M FM5 TP(5)  
0.1UF D 50V 80%,-20% F(Y5V) TA  
1UF 50V Z F TA26 D  
10M SRE/SE 16V M FM5 TP(5)  
10M SRE/SE 16V M FM5 TP(5)  
0.022UF 50V Z F TA26 S  
0.022UF 50V Z F TA26 S  
0.01M 16V M Y TA26  
220M SRA 6.3V M FM5 TP(5)  
- 5-3 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MODEL : NTH960  
RUN DATE : 2004.05.01  
S
AL LOCA.NO.  
C332  
C333  
C334  
C336  
C337  
C338  
C339  
C340  
C341  
C343  
C344  
C345  
C346  
C348  
C349  
C354  
C355  
C358  
C360  
C368  
C369  
C375  
C377  
C380  
C381  
C384  
C386  
C3B1  
C3G1  
C3G2  
C3G3  
C3G4  
C3G5  
C3G6  
C3G7  
C3G8  
C3G9  
C401  
C402  
C403  
C405  
C406  
C410  
C412  
C413  
C414  
C415  
C416  
C417  
C418  
C419  
C420  
C421  
C424  
C431  
C466  
C480  
C490  
C501  
C502  
PART NO  
DESCRIPTION  
SPECIFICATION  
0.01M 16V M Y TA26  
0.1UF D 50V 80%,-20% F(Y5V) TA  
0.022UF 50V Z F TA26 S  
0.01M 16V M Y TA26  
4.7UF SRA,SS 50V 20% FM5 TP 5  
0.022UF 50V Z F TA26 S  
1.0M SRA/SS50V M FM5 TP(5)  
0.033UF 50V K B TA26  
REMARK  
0CN1030F678  
0CN1040K948  
0CN223AK948  
0CN1030F678  
0CE4754K638  
0CN223AK948  
0CE1054K638  
0CN3330K518  
0CN223AK948  
0CN4730K948  
0CN1040K948  
0CN1040K948  
0CE2274C638  
0CN1030F678  
0CN223AK948  
0CE2274C638  
0CN1030F678  
0CE1054K638  
0CC0500K015  
0CN1020K518  
0CN1040K948  
0CN1040K948  
0CE1044K638  
0CN223AK948  
0CE4764F638  
0CE4774C638  
0CN223AK948  
0CN3330K518  
0CN223AK948  
0CE4764F638  
0CN3320F668  
0CN4730K948  
0CE4754K638  
0CE4754K638  
0CE4754K638  
0CN1030F678  
0CN223AK948  
0CE4764F638  
0CN223AK948  
0CN1040K948  
0CE1063F638  
0CE1063F638  
0CN1040K948  
0CN1040K948  
0CQ1032K409  
0CQ1032K409  
0CE2264F638  
0CN2220F668  
0CN1820F668  
0CQ1532K409  
0CQ1032K409  
0CE4765K618  
0CQ2232L559  
0CN1040K948  
0CN1030F678  
0CE3354K638  
0CE4754K638  
0CE1054K638  
0CN1040K948  
0CE4764C638  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,FIXED TUBULAR(High d  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,FIXED TUBULAR(High d  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,ELECTROLYTIC  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,ELECTROLYTIC  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,CERAMIC(TEMP COMP)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,ELECTROLYTIC  
0.022UF 50V Z F TA26 S  
0.047UF D 50V 80%,-20% F(Y5V)  
0.1UF D 50V 80%,-20% F(Y5V) TA  
0.1UF D 50V 80%,-20% F(Y5V) TA  
220M SRA 6.3V M FM5 TP(5)  
0.01M 16V M Y TA26  
0.022UF 50V Z F TA26 S  
220M SRA 6.3V M FM5 TP(5)  
0.01M 16V M Y TA26  
1.0M SRA/SS50V M FM5 TP(5)  
5P 50V C NP0 TR  
1000P 50V K B TA26  
0.1UF D 50V 80%,-20% F(Y5V) TA  
0.1UF D 50V 80%,-20% F(Y5V) TA  
0.1M SRA 50V M FM5 TP(5)  
0.022UF 50V Z F TA26 S  
47M SRA/SS 16V M FM5 TP(5)  
470UF SRA,SS 6.3V 20% FM5 TP 5  
0.022UF 50V Z F TA26 S  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,FIXED TUBULAR(High d  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,FIXED TUBULAR(High d  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,AL.ELECTROLYTIC  
CAPACITOR,AL.ELECTROLYTIC  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,FIXED FILM  
0.033UF 50V K B TA26  
0.022UF 50V Z F TA26 S  
47M SRA/SS 16V M FM5 TP(5)  
3300P 16V  
M
TA26  
0.047UF D 50V 80%,-20% F(Y5V)  
4.7UF SRA,SS 50V 20% FM5 TP 5  
4.7UF SRA,SS 50V 20% FM5 TP 5  
4.7UF SRA,SS 50V 20% FM5 TP 5  
0.01M 16V M Y TA26  
0.022UF 50V Z F TA26 S  
47M SRA/SS 16V M FM5 TP(5)  
0.022UF 50V Z F TA26 S  
0.1UF D 50V 80%,-20% F(Y5V) TA  
10M SRE/SE 16V M FM5 TP(5)  
10M SRE/SE 16V M FM5 TP(5)  
0.1UF D 50V 80%,-20% F(Y5V) TA  
0.1UF D 50V 80%,-20% F(Y5V) TA  
0.01UF S 50V 5% PE TP5  
0.01UF S 50V 5% PE TP5  
22UF SRA,SS 16V 20% FM5 TP 5  
2200P 16V M X TA26  
CAPACITOR,FIXED FILM  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,FIXED FILM  
CAPACITOR,FIXED FILM  
CAPACITOR,AL.ELECTROLYTIC  
CAPACITOR,FIXED FILM  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
1800P 16V M X TA26  
0.015UF S 50V 5% PE TP5  
0.01UF S 50V 5% PE TP5  
47UF SR,SV 50V M FL TP 5  
0.022UF S 63V 10% PP NI TP5  
0.1UF D 50V 80%,-20% F(Y5V) TA  
0.01M 16V M Y TA26  
3.3UF SRA,SS 50V 20% FM5 TP 5  
4.7UF SRA,SS 50V 20% FM5 TP 5  
1.0M SRA/SS50V M FM5 TP(5)  
0.1UF D 50V 80%,-20% F(Y5V) TA  
47M SRA 6.3V M FM5 TP(5)  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,ELECTROLYTIC  
- 5-4 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MODEL : NTH960  
RUN DATE : 2004.05.01  
S
AL LOCA.NO.  
C503  
C505  
C507  
C509  
C510  
C514  
C515  
C516  
C517  
C520  
C521  
C522  
C525  
C526  
C528  
C529  
C530  
C534  
C535  
C540  
C541  
C542  
C543  
C544  
C545  
C546  
C551  
C552  
C554  
C555  
C557  
C561  
C567  
C570  
C571  
C573  
C574  
C576  
C581  
C582  
C583  
C584  
C5F1  
C5F2  
C6F3  
C6F4  
C6F5  
C6F8  
C5K0  
C5K1  
C5K2  
C6R1  
C601  
C602  
C603  
C604  
C605  
C901  
C902  
C903  
C904  
PART NO  
DESCRIPTION  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
SPECIFICATION  
REMARK  
0CE4774C638  
0CE1074F638  
0CN1030F678  
0CN223AK948  
0CN1030F678  
0CC1500K415  
0CC1200K415  
0CE1054K636  
0CE4774C638  
0CN1030F678  
0CN1040K948  
0CN1030F678  
0CN223AK948  
0CE4764J638  
0CN1030F678  
0CN1040K948  
0CE4764C638  
0CE4754K638  
0CE4754K638  
0CE4764F638  
0CE4754K638  
0CN6810K518  
0CN2220F668  
0CQ3332K409  
0CN2220F668  
0CE4764H638  
0CQ4732K409  
0CN1030F678  
0CN1040K948  
0CE2264F638  
0CN1040K948  
0CE4764C638  
0CN1020K518  
0CC1200K415  
0CC1500K415  
0CN5610K518  
0CN1020K518  
0CE2264F638  
0CN1030F678  
0CN1030F678  
0CN1040K948  
0CE1054K636  
0CE4766K638  
0CE4766K638  
0CE4764C638  
0CN1030F678  
0CN1030F678  
0CE4766K638  
0CN1030F678  
0CN1030F678  
0CN1030F678  
0CE4764C638  
0CN1030F678  
0CN1030F678  
0CN1030F678  
0CN1030F678  
0CN1030F678  
0CN1020K518  
0CN1020K518  
0CN1020K518  
0CN1020K518  
470UF SRA,SS 6.3V 20% FM5 TP 5  
100U SRA 16V M FM5 TP(5)  
0.01M 16V M Y TA26  
0.022UF 50V Z F TA26 S  
0.01M 16V M Y TA26  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,CERAMIC(TEMP COMP)  
CAPACITOR,FIXED CERAMIC(TEMP.C  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,AL.ELECTROLYTIC  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,FIXED FILM  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,FIXED FILM  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,ELECTROLYTIC  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,FIXED CERAMIC(TEMP.C  
CAPACITOR,CERAMIC(TEMP COMP)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,FIXED TUBULAR(HIGH D  
CAPACITOR,ELECTROLYTIC  
15P 50V J NP0 TS  
12PF D 50V 5% TR NP0  
1.0U SRA 50V M FM5 BP TP(D)  
470UF SRA,SS 6.3V 20% FM5 TP 5  
0.01M 16V M Y TA26  
0.1UF D 50V 80%,-20% F(Y5V) TA  
0.01M 16V M Y TA26  
0.022UF 50V Z F TA26 S  
47UF SRA,SS 35V M FM5 TP 5  
0.01M 16V M Y TA26  
0.1UF D 50V 80%,-20% F(Y5V) TA  
47M SRA 6.3V M FM5 TP(5)  
4.7UF SRA,SS 50V 20% FM5 TP 5  
4.7UF SRA,SS 50V 20% FM5 TP 5  
47M SRA/SS 16V M FM5 TP(5)  
4.7UF SRA,SS 50V 20% FM5 TP 5  
680P 50V K B TA26  
2200P 16V M X TA26  
0.033UF S 50V 5% PE TP5  
2200P 16V M X TA26  
47M SRA 25V M FM5 TP(5)  
0.047UF S 50V 5% PE TP5  
0.01M 16V M Y TA26  
0.1UF D 50V 80%,-20% F(Y5V) TA  
22UF SRA,SS 16V 20% FM5 TP 5  
0.1UF D 50V 80%,-20% F(Y5V) TA  
47M SRA 6.3V M FM5 TP(5)  
1000P 50V K B TA26  
12PF D 50V 5% TR NP0  
15P 50V J NP0 TS  
560P 50V K B TA26  
1000P 50V K B TA26  
22UF SRA,SS 16V 20% FM5 TP 5  
0.01M 16V M Y TA26  
0.01M 16V M Y TA26  
0.1UF D 50V 80%,-20% F(Y5V) TA  
1.0U SRA 50V M FM5 BP TP(D)  
47M SMS 50V M FM5 TP  
47M SMS 50V M FM5 TP  
47M SRA 6.3V M FM5 TP(5)  
0.01M 16V M Y TA26  
0.01M 16V M Y TA26  
47M SMS 50V M FM5 TP  
0.01M 16V M Y TA26  
0.01M 16V M Y TA26  
0.01M 16V M Y TA26  
47M SRA 6.3V M FM5 TP(5)  
0.01M 16V M Y TA26  
0.01M 16V M Y TA26  
0.01M 16V M Y TA26  
0.01M 16V M Y TA26  
0.01M 16V M Y TA26  
1000P 50V K B TA26  
1000P 50V K B TA26  
1000P 50V K B TA26  
1000P 50V K B TA26  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,ELECTROLYTIC  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR,ELECTROLYTIC  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(HIGH DIELE)  
CAPACITOR TUBULA(HIGH DIELE)  
- 5-5 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MODEL : NTH960  
RUN DATE : 2004.05.01  
S
AL LOCA.NO.  
C906  
PART NO  
DESCRIPTION  
SPECIFICATION  
0.022UF 50V Z F TA26 S  
REMARK  
0CN223AK948  
0CE4764F638  
0CE1054K638  
0CE1054K638  
0CE1054K638  
0CE1054K638  
0CN223AK948  
0CE4754K638  
0CE1064F638  
0CE1074F638  
0CX2700K408  
0CE2264F638  
0CE4774C638  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,TUBULAR(HIGH DIELEC)  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR,ELECTROLYTIC  
CAPACITOR TUBULA(T.C)  
CAPACITOR,FIXED ELECTROLYTIC  
CAPACITOR,FIXED ELECTROLYTIC  
COIL  
C907  
C908  
C909  
C910  
C911  
C917  
C918  
C919  
C921  
C922  
C923  
C924  
47M SRA/SS 16V M FM5 TP(5)  
1.0M SRA/SS50V M FM5 TP(5)  
1.0M SRA/SS50V M FM5 TP(5)  
1.0M SRA/SS50V M FM5 TP(5)  
1.0M SRA/SS50V M FM5 TP(5)  
0.022UF 50V Z F TA26 S  
4.7UF SRA,SS 50V 20% FM5 TP 5  
10M SRA 16V M FM5 TP(5)  
100U SRA 16V M FM5 TP(5)  
27P 50V J SL TA26  
22UF SRA,SS 16V 20% FM5 TP 5  
470UF SRA,SS 6.3V 20% FM5 TP 5  
FL401  
L103  
L104  
L301  
L302  
L303  
L304  
L306  
L307  
L309  
L380  
L3G1  
L401  
L405  
L503  
L504  
L505  
L901  
L902  
L904  
633-032KCOIL,IFT  
633-088G  
633-088G  
NON  
BIAC  
OSC,1CHIP  
S-75M5)V(K  
COIL,CHOKE  
COIL,CHOKE  
22MH TOKO 5MM TP  
22MH TOKO 5MM TP  
180M K 6X6 L5 TP  
47M K 2.3X3.4 L5 TP  
120M K 2.3X3.4 L5 TP  
470M K 6X6 L5 TP  
220M K 6X6 L5 TP  
470M K 6X6 L5 TP  
270UH 5% 4X5 TR5  
100M K 6X6 L5 TP  
100M K 6X6 L5 TP  
100M K 6X6 L5 TP  
100M K 6X6 L5 TP  
100M K 6X6 L5 TP  
100M K 2.3X3.4 L5 TP  
100M K 6X6 L5 TP  
100M K 2.3X3.4 L5 TP  
100M K 2.3X3.4 L5 TP  
100M K 6X6 L5 TP  
0LR1800K035  
0LA0472K018  
0LA1200K018  
0LR4700K035  
0LR2200K035  
0LR4700K035  
0LR2700J025  
0LR1000K035  
0LR1000K035  
0LR1000K035  
0LR1000K035  
0LR1000K035  
0LA1000K018  
0LR1000K035  
0LA1000K018  
0LA1000K018  
0LR1000K035  
INDUCTOR RADIAL LEAD  
INDUCTOR AXIAL LEAD  
INDUCTOR AXIAL LEAD  
INDUCTOR RADIAL LEAD  
INDUCTOR RADIAL LEAD  
INDUCTOR RADIAL LEAD  
INDUCTOR,RADIAL LEAD  
INDUCTOR RADIAL LEAD  
INDUCTOR RADIAL LEAD  
INDUCTOR RADIAL LEAD  
INDUCTOR RADIAL LEAD  
INDUCTOR RADIAL LEAD  
INDUCTOR AXIAL LEAD  
INDUCTOR RADIAL LEAD  
INDUCTOR AXIAL LEAD  
INDUCTOR AXIAL LEAD  
INDUCTOR RADIAL LEAD  
DIODE  
BD101  
D102  
D103  
D106  
D107  
D108  
D109  
D110  
D154  
D155  
D156  
D158  
D159  
D161  
D301  
D380  
D401  
D402  
D403  
D501  
D510  
D511  
D5F6  
D901  
D902  
0DD160000DA  
0DD010009CA  
0DR180209AA  
0DR158220AA  
0DR180209AA  
0DD010009AC  
0DR302000AB  
0DD010009AC  
0DD207000AB  
0DD207000AB  
0DD207000AB  
0DR104009AB  
0DR104009AB  
0DR104009AB  
0DD133009AA  
0DD133009AA  
0DD133009AA  
0DD133009AA  
0DD133009AA  
0DD133009AA  
0DD133009AA  
0DD133009AA  
0DD133009AA  
0DD133009AA  
0DD133009AA  
DIODE,RECTIFIERS  
DIODE,RECTIFIERS  
DIODE,RECTIFIERS  
DIODE,RECTIFIERS  
DIODE,RECTIFIERS  
DIODE,RECTIFIERS  
DIODE,RECTIFIERS  
DIODE,RECTIFIERS  
DIODE,RECTIFIERS  
DIODE,RECTIFIERS  
DIODE,RECTIFIERS  
DIODE,RECTIFIERS  
DIODE,RECTIFIERS  
DIODE,RECTIFIERS  
DIODE,SWITCHING  
DIODE,SWITCHING  
DIODE,SWITCHING  
DIODE,SWITCHING  
DIODE,SWITCHING  
DIODE,SWITCHING  
DIODE,SWITCHING  
DIODE,SWITCHING  
DIODE,SWITCHING  
DIODE,SWITCHING  
S1WBA60 BK SHINDENGEN - 600V -  
EG01C TP SANKEN - - - - - -  
ERA18-02KFRB TP FUJI DO204AL 2  
1N5822 BK RECTRON DO201AD 40V  
ERA18-02KFRB TP FUJI DO204AL 2  
EU01W(R-FORM) TP SANKEN  
HER302 BK RECTRON DO201AD 100V  
EU01W(R-FORM) TP SANKEN  
2A07 2A RECT(T/S)P=12.5 F DELT  
2A07 2A RECT(T/S)P=12.5 F DELT  
2A07 2A RECT(T/S)P=12.5 F DELT  
RL104 R. TP GULF SEMICONDUCTOR  
RL104 R. TP GULF SEMICONDUCTOR  
RL104 R. TP GULF SEMICONDUCTOR  
1SS133 DETECT,SW TP  
1SS133 DETECT,SW TP  
1SS133 DETECT,SW TP  
1SS133 DETECT,SW TP  
1SS133 DETECT,SW TP  
1SS133 DETECT,SW TP  
1SS133 DETECT,SW TP  
1SS133 DETECT,SW TP  
1SS133 DETECT,SW TP  
1SS133 DETECT,SW TP  
1SS133 DETECT,SW TP  
DIODE,SWITCHING  
- 5-6 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MODEL : NTH960  
RUN DATE : 2004.05.01  
S
AL LOCA.NO.  
D903  
PART NO  
DESCRIPTION  
SPECIFICATION  
REMARK  
0DD133009AA  
0DD133009AA  
0DD133009AA  
DIODE,SWITCHING  
DIODE,SWITCHING  
DIODE,SWITCHING  
DIGITRON  
1SS133 DETECT,SW TP  
1SS133 DETECT,SW TP  
1SS133 DETECT,SW TP  
D904  
D905  
DG601  
6302R-V106A  
DIGITRON  
9MT-173GNK FUTABA UNIVERSAL LV  
FILTER  
BC101  
BD901  
BD902  
BD903  
BD904  
BD905  
BD906  
BD907  
BD908  
BD909  
BD910  
BD911  
BD922  
L102  
636-004C  
636-004C  
636-004C  
636-004C  
636-004C  
636-004C  
636-004C  
636-004C  
636-004C  
636-004C  
636-004C  
636-004C  
636-004C  
616-145H  
636-004C  
FILTER(CIRC),EMC  
FILTER(CIRC),EMC  
FILTER(CIRC),EMC  
FILTER(CIRC),EMC  
FILTER(CIRC),EMC  
FILTER(CIRC),EMC  
FILTER(CIRC),EMC  
FILTER(CIRC),EMC  
FILTER(CIRC),EMC  
FILTER(CIRC),EMC  
FILTER(CIRC),EMC  
FILTER(CIRC),EMC  
FILTER(CIRC),EMC  
FILTER(CIRC),DRAWING  
FILTER(CIRC),EMC  
FUSE  
BEAD CORE BFS3550R2FD8,R T/P  
BEAD CORE BFS3550R2FD8,R T/P  
BEAD CORE BFS3550R2FD8,R T/P  
BEAD CORE BFS3550R2FD8,R T/P  
BEAD CORE BFS3550R2FD8,R T/P  
BEAD CORE BFS3550R2FD8,R T/P  
BEAD CORE BFS3550R2FD8,R T/P  
BEAD CORE BFS3550R2FD8,R T/P  
BEAD CORE BFS3550R2FD8,R T/P  
BEAD CORE BFS3550R2FD8,R T/P  
BEAD CORE BFS3550R2FD8,R T/P  
BEAD CORE BFS3550R2FD8,R T/P  
BEAD CORE BFS3550R2FD8,R T/P  
SHT LFS2020V4-04350  
W1A2  
BEAD CORE BFS3550R2FD8,R T/P  
F101  
0FS1601B51B  
FUSE,SLOW BLOW  
HOLDER  
1600MA 250 V 5.2X20 CY/GL KS /  
ES501  
ES502  
FH01  
FH02  
LD501  
4931R-0050A  
4931R-0050A  
586-008B  
586-008B  
4931R-0017A  
HOLDER ASSY  
HOLDER ASSY  
HOLDER  
HOLDER  
HOLDER ASSEMBLY  
IC  
END  
END  
FUSE CLIP TP SINSUNG  
FUSE CLIP TP SINSUNG  
MV995A NON LED  
F104  
GIRH100000B  
0ISK615300A  
0ISS431000A  
0ISA715820A  
0IMA391600A  
0IMCRMA024B  
0ICS241600B  
0IKE704200B  
0IPRPPY002A  
0IJR641300A  
IC,ROHM  
IC,SANKEN  
IC,SAMSUNG ELECTRONICS  
IC,SANYO  
IC,MATSUSHITA  
IC,MICRO CONTROLLER  
IC,CATALYST  
IC,KEC  
IC,PERIPHERALS  
IC,JRC  
ICP-N10 T104 TP IC DETACT  
STR-G6153T 5PIN FM CUT BK PWM  
KA431AZ (LM431AZ)  
LA71582M 100QFP BK AVCP TIMELA  
AN3916 SDIP ST AGC IC  
MN101D06F LE 2ND MATSUSHITA 10  
CAT24WC16P 8P DIP ST 16K SERIA  
KIA7042P 3P 4.2V RESET(TAPING)  
PT6315 PTC 44 LQFP TRAY VFD DR  
NJU6413AD 16P DIP ST RS232C DR  
IC101  
IC103  
IC301  
IC3G1  
IC501  
IC503  
IC505  
IC6F1  
IC901  
JACK  
JK901  
JK902  
572-034R  
572-034R  
JACK,RCA  
JACK,RCA  
BJP-202-WH BAE EUN (WHITE) ST,  
BJP-202-WH BAE EUN (WHITE) ST,  
LED  
LD601  
LD602  
6301R1K001A  
6301R1K001A  
LED ASSY  
LED ASSY  
LTL16KEEH74 LITEON KOREA 17  
LTL16KEEH74 LITEON KOREA 17  
RESISTOR  
FR101  
R101  
R102  
R103  
R104  
R107  
R109  
R114  
R116  
R117  
R118  
R119  
R120  
0RF0471Q619  
614-007A  
RESISTOR,DRAWING  
RESISTOR  
4.7 OHM 1/4 W(3.4) 5.00% TR  
2.7/2W CEMENT SMPS V  
100K OHM 2 W 5.00% TR  
6.8 OHM 1/6 W 5.00% TA26  
56K OHM 2 W 5.00% TR  
1.5M OHM 1/2 W 5.00% MF10  
0.35 OHM 2 W 5.00% TR  
100K OHM 1/6 W 5% TA26  
330 OHM 1/6 W 5% TA26  
2.2K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
3.3K OHM 1/6 W 1% TA26  
2.7K OHM 1/6 W 1% TA26  
0RS1003K619  
0RD0681F608  
0RS5602K619  
0RD1504H632  
0RS0350K619  
0RD1003F608  
0RD3300F608  
0RD2201F608  
0RD1001F608  
0RN3301F408  
0RN2701F408  
RESISTOR,FIXED METAL OXIDE FIL  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED METAL OXIDE FIL  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED METAL OXIDE FIL  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED METAL FILM  
RESISTOR,FIXED METAL FILM  
- 5-7 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MODEL : NTH960  
RUN DATE : 2004.05.01  
S
AL LOCA.NO.  
R121  
R122  
R152  
R156  
R157  
R161  
R162  
R166  
R167  
R168  
R170  
R171  
R172  
R173  
R174  
R175  
R177  
R302  
R303  
R304  
R305  
R306  
R307  
R308  
R309  
R310  
R311  
R312  
R313  
R316  
R317  
R318  
R319  
R320  
R321  
R322  
R326  
R335  
R338  
R340  
R341  
R349  
R380  
R381  
R384  
R385  
R386  
R387  
R388  
R389  
R390  
R391  
R392  
R393  
R3B1  
R3G1  
R3G2  
R3G3  
R3G4  
R3G5  
PART NO  
DESCRIPTION  
SPECIFICATION  
REMARK  
0RD1800F608  
0RD1003F608  
0RD5600F608  
0RD1001F608  
0RD3300F608  
0RD4701F608  
0RD4701F608  
0RD2201F608  
0RD3901F608  
0RD4701F608  
0RD1001F608  
0RD3301F608  
0RD4701F608  
0RD1001F608  
0RD3300F608  
0RD4701F608  
0RD4701F608  
0RD1002F608  
0RD1802F608  
0RD1002F608  
0RD1001F608  
0RD2700F608  
0RD3300F608  
0RD2701F608  
0RD6800F608  
0RD1001F608  
0RD4701F608  
0RD1801F608  
0RD2700F608  
0RD1500F608  
0RD6802F608  
0RD1001F608  
0RD1001F608  
0RD1501F608  
0RD1801F608  
0RD8201F608  
0RD2701F608  
0RD3902F608  
0RD2700F608  
0RD1802F608  
0RD2701F608  
0RD5601F608  
0RD2200F608  
0RD1001F608  
0RD1800F608  
0RD1800F608  
0RD0752F608  
0RD1004F608  
0RD0752F608  
0RD1502F608  
0RD5601F608  
0RD4702F608  
0RD2201F608  
0RD4702F608  
0RD3901F608  
0RD5601F608  
0RD2702F608  
0RD3902F608  
0RD1503F608  
0RD1800F608  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
180 OHM 1/6 W 5% TA26  
100K OHM 1/6 W 5% TA26  
560 OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
330 OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
2.2K OHM 1/6 W 5% TA26  
3.9K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
3.3K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
330 OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
18K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
270 OHM 1/6 W 5% TA26  
330 OHM 1/6 W 5% TA26  
2.7K OHM 1/6 W 5% TA26  
680 OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
1.8K OHM 1/6 W 5% TA26  
270 OHM 1/6 W 5% TA26  
150 OHM 1/6 W 5% TA26  
68K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1.5K OHM 1/6 W 5% TA26  
1.8K OHM 1/6 W 5% TA26  
8.2K OHM 1/6 W 5% TA26  
2.7K OHM 1/6 W 5% TA26  
39K OHM 1/6 W 5% TA26  
270 OHM 1/6 W 5% TA26  
18K OHM 1/6 W 5% TA26  
2.7K OHM 1/6 W 5% TA26  
5.6K OHM 1/6 W 5% TA26  
220 OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
180 OHM 1/6 W 5% TA26  
180 OHM 1/6 W 5% TA26  
75 OHM 1/6 W 5.00% TA26  
1M OHM 1/6 W 5% TA26  
75 OHM 1/6 W 5.00% TA26  
15K OHM 1/6 W 5% TA26  
5.6K OHM 1/6 W 5% TA26  
47K OHM 1/6 W 5% TA26  
2.2K OHM 1/6 W 5% TA26  
47K OHM 1/6 W 5% TA26  
3.9K OHM 1/6 W 5% TA26  
5.6K OHM 1/6 W 5% TA26  
27K OHM 1/6 W 5% TA26  
39K OHM 1/6 W 5% TA26  
150K OHM 1/6 W 5% TA26  
180 OHM 1/6 W 5% TA26  
- 5-8 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S
AL LOCA.NO.  
R3G6  
R402  
R403  
R404  
R406  
R408  
R409  
R410  
R411  
R412  
R413  
R414  
R415  
R416  
R418  
R419  
R420  
R421  
R424  
R425  
R430  
R431  
R482  
R486  
R488  
R490  
R491  
R492  
R493  
R501  
R502  
R504  
R505  
R507  
R508  
R509  
R510  
R511  
R512  
R513  
R515  
R516  
R517  
R6F1  
R6F2  
R521  
R522  
R525  
R526  
R527  
R529  
R532  
R534  
R541  
R543  
R544  
R546  
R547  
R548  
R550  
PART NO  
DESCRIPTION  
SPECIFICATION  
REMARK  
0RD1800F608  
0RD2204F608  
0RD6801F608  
0RD5600F608  
0RD3301F608  
0RD2201F608  
0RD4701F608  
0RD1002F608  
0RD2202F608  
0RD1801F608  
0RD8201F608  
0RD1202F608  
0RD3303F608  
0RD1800F608  
0RD1802F608  
0RD0472F608  
0RD1001F608  
0RD0221F608  
0RD2700F608  
0RD4702F608  
0RD3901F608  
0RD4701F608  
0RD1001F608  
0RD5600F608  
0RD2202F608  
0RD4702F608  
0RD1202F608  
0RD1501F608  
0RD0102F608  
0RD2200F608  
0RD2200F608  
0RD1001F608  
0RD1001F608  
0RD1201F608  
0RD5600F608  
0RD6800F608  
0RD1503F608  
0RD1001F608  
0RD1001F608  
0RD3901F608  
0RD2700F608  
0RD2200F608  
0RD2200F608  
0RD5600F608  
0RD5600F608  
0RD1002F608  
0RD1001F608  
0RD1002F608  
0RD1002F608  
0RD1000F608  
0RD1002F608  
0RD6802F608  
0RD2201F608  
0RD2201F608  
0RD2701F608  
0RD4701F608  
0RD4701F608  
0RD1002F608  
0RD1003F608  
0RD2200F608  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
180 OHM 1/6 W 5% TA26  
2.2M OHM 1/6 W 0.05 TA26  
6.8K OHM 1/6 W 5% TA26  
560 OHM 1/6 W 5% TA26  
3.3K OHM 1/6 W 5% TA26  
2.2K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
22K OHM 1/6 W 5% TA26  
1.8K OHM 1/6 W 5% TA26  
8.2K OHM 1/6 W 5% TA26  
12K OHM 1/6 W 5% TA26  
330K OHM 1/6 W 5% TA26  
180 OHM 1/6 W 5% TA26  
18K OHM 1/6 W 5% TA26  
47 OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
2.2 OHM 1/6 W 5% TA26  
270 OHM 1/6 W 5% TA26  
47K OHM 1/6 W 5% TA26  
3.9K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
560 OHM 1/6 W 5% TA26  
22K OHM 1/6 W 5% TA26  
47K OHM 1/6 W 5% TA26  
12K OHM 1/6 W 5% TA26  
1.5K OHM 1/6 W 5% TA26  
10 OHM 1/6 W 5% TA26  
220 OHM 1/6 W 5% TA26  
220 OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1.2K OHM 1/6 W 5% TA26  
560 OHM 1/6 W 5% TA26  
680 OHM 1/6 W 5% TA26  
150K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
3.9K OHM 1/6 W 5% TA26  
270 OHM 1/6 W 5% TA26  
220 OHM 1/6 W 5% TA26  
220 OHM 1/6 W 5% TA26  
560 OHM 1/6 W 5% TA26  
560 OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
100 OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
68K OHM 1/6 W 5% TA26  
2.2K OHM 1/6 W 5% TA26  
2.2K OHM 1/6 W 5% TA26  
2.7K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
100K OHM 1/6 W 5% TA26  
220 OHM 1/6 W 5% TA26  
- 5-9 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MODEL : NTH960  
RUN DATE : 2004.05.01  
S
AL LOCA.NO.  
R553  
R554  
R555  
R556  
R557  
R558  
R559  
R560  
R563  
R564  
R567  
R569  
R570  
R571  
R572  
R573  
R574  
R575  
R576  
R577  
R578  
R579  
R580  
R581  
R582  
R583  
R585  
R589  
R590  
R591  
R592  
R593  
R595  
R596  
R597  
R598  
R5B1  
R5B3  
R5B4  
R5C5  
R5C6  
R5C7  
R5F0  
R5F1  
R5F2  
R5F3  
R6F4  
R6F5  
R6F6  
R6F7  
R5K0  
R5K1  
R5K2  
R6R1  
R603  
R604  
R605  
R606  
R607  
R608  
R609  
PART NO  
DESCRIPTION  
SPECIFICATION  
REMARK  
0RD2200F608  
0RD4700F608  
0RD2200F608  
0RD2202F608  
0RD2702F608  
0RD2202F608  
0RD4701F608  
0RD4701F608  
0RD4701F608  
0RD2702F608  
0RD4701F608  
0RD4701F608  
0RD4701F608  
0RD2202F608  
0RD1001F608  
0RD8200F608  
0RD4701F608  
0RD4701F608  
0RD4701F608  
0RD4701F608  
0RD4701F608  
0RD5602F608  
0RD5600F608  
0RD5600F608  
0RD1001F608  
0RD1002F608  
0RD1001F608  
0RD2700F608  
0RD1001F608  
0RD4701F608  
0RD4702F608  
0RD1202F608  
0RD1000F608  
0RD1000F608  
0RD1000F608  
0RD1000F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD0122F608  
0RD0122F608  
0RD0102F608  
0RD0102F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD5602F608  
0RD1002F608  
0RD1002F608  
0RD1002F608  
0RD3300F608  
0RD1801F608  
0RD1801F608  
0RD1501F608  
0RD1501F608  
0RD2201F608  
0RD2201F608  
0RD2701F608  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
220 OHM 1/6 W 5% TA26  
470 OHM 1/6 W 5% TA26  
220 OHM 1/6 W 5% TA26  
22K OHM 1/6 W 5% TA26  
27K OHM 1/6 W 5% TA26  
22K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
27K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
22K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
820 OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
56K OHM 1/6 W 5% TA26  
560 OHM 1/6 W 5% TA26  
560 OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
270 OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
4.7K OHM 1/6 W 5% TA26  
47K OHM 1/6 W 5% TA26  
12K OHM 1/6 W 5% TA26  
100 OHM 1/6 W 5% TA26  
100 OHM 1/6 W 5% TA26  
100 OHM 1/6 W 5% TA26  
100 OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
12 OHM 1/6 W 5.00% TA26  
12 OHM 1/6 W 5.00% TA26  
10 OHM 1/6 W 5% TA26  
10 OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
56K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
330 OHM 1/6 W 5% TA26  
1.8K OHM 1/6 W 5% TA26  
1.8K OHM 1/6 W 5% TA26  
1.5K OHM 1/6 W 5% TA26  
1.5K OHM 1/6 W 5% TA26  
2.2K OHM 1/6 W 5% TA26  
2.2K OHM 1/6 W 5% TA26  
2.7K OHM 1/6 W 5% TA26  
- 5-10 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MODEL : NTH960  
RUN DATE : 2004.05.01  
S
AL LOCA.NO.  
R610  
R611  
R612  
R613  
R614  
R615  
R616  
R617  
R618  
R621  
R622  
R623  
R624  
R625  
R626  
R627  
R628  
R629  
R630  
R634  
R635  
R636  
R637  
R638  
R904  
R905  
R906  
R907  
R908  
R909  
R910  
R911  
R912  
R914  
R915  
R916  
R917  
R918  
R919  
R920  
R921  
R922  
R923  
R924  
R925  
R926  
R927  
R928  
R929  
R930  
R931  
R932  
R933  
R934  
R935  
R936  
R937  
R938  
R939  
R940  
PART NO  
DESCRIPTION  
SPECIFICATION  
REMARK  
0RD2701F608  
0RD3901F608  
0RD3901F608  
0RD6801F608  
0RD6801F608  
0RD1202F608  
0RD1202F608  
0RD6802F608  
0RD1002F608  
0RD1801F608  
0RD1501F608  
0RD2201F608  
0RD2701F608  
0RD6802F608  
0RD6802F608  
0RD6802F608  
0RD6802F608  
0RD6802F608  
0RD6802F608  
0RD0101F608  
0RD0101F608  
0RD0101F608  
0RD0101F608  
0RD0101F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD1001F608  
0RD1002F608  
0RD1002F608  
0RD1002F608  
0RD1002F608  
0RD1002F608  
0RD1002F608  
0RD1002F608  
0RD1002F608  
0RD1002F608  
0RD1002F608  
0RD1002F608  
0RD1002F608  
0RD1002F608  
0RD1002F608  
0RD1001F608  
0RD5600F608  
0RD1002F608  
0RD1001F608  
0RD2201F608  
0RD1001F608  
0RD1002F608  
0RD2702F608  
0RD8201F608  
0RD2200F608  
0RD0562F608  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
RESISTOR,FIXED CARBON FILM  
2.7K OHM 1/6 W 5% TA26  
3.9K OHM 1/6 W 5% TA26  
3.9K OHM 1/6 W 5% TA26  
6.8K OHM 1/6 W 5% TA26  
6.8K OHM 1/6 W 5% TA26  
12K OHM 1/6 W 5% TA26  
12K OHM 1/6 W 5% TA26  
68K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
1.8K OHM 1/6 W 5% TA26  
1.5K OHM 1/6 W 5% TA26  
2.2K OHM 1/6 W 5% TA26  
2.7K OHM 1/6 W 5% TA26  
68K OHM 1/6 W 5% TA26  
68K OHM 1/6 W 5% TA26  
68K OHM 1/6 W 5% TA26  
68K OHM 1/6 W 5% TA26  
68K OHM 1/6 W 5% TA26  
68K OHM 1/6 W 5% TA26  
1 OHM 1/6 W 5.00% TA26  
1 OHM 1/6 W 5.00% TA26  
1 OHM 1/6 W 5.00% TA26  
1 OHM 1/6 W 5.00% TA26  
1 OHM 1/6 W 5.00% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
560 OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
2.2K OHM 1/6 W 5% TA26  
1K OHM 1/6 W 5% TA26  
10K OHM 1/6 W 5% TA26  
27K OHM 1/6 W 5% TA26  
8.2K OHM 1/6 W 5% TA26  
220 OHM 1/6 W 5% TA26  
56 OHM 1/6 W 5% TA26  
- 5-11 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S
AL LOCA.NO.  
VR501  
PART NO  
613-032W  
611-024B  
DESCRIPTION  
RESISTOR,DRAWING  
RESISTOR,DRAWING  
REMOTE CONTROLLER RECEIVER  
REMOTE CONTROLLER RECEIVER  
SENSOR  
SPECIFICATION  
RH063MCJ5R (220K)  
RK09K113000123B  
REMARK  
VR601  
RC6R1  
6712R2938GA  
TSOP1238SP1 VISHAY(TEMIC) 37-9  
IC102  
RS501  
RS502  
657-063A  
6500RAB003A  
6500RAB003A  
SENSOR  
SENSOR  
SENSOR  
LTV-817B,PHOTO COUPLER(LITEON)  
SG-260 KODENSHI D33 REEL SENSO  
SG-260 KODENSHI D33 REEL SENSO  
SWITCH  
CS501  
JS601  
MS501  
SL601  
6600M000026  
556-272A  
6600JB8005B  
6600Q000007  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
556-219B  
SWITCH,PUSH  
SWITCH  
MPU12970MLB0 VCR CST IN S/W MI  
JRS0000-0502 SMK NON 1V 10MA V  
NON 5V 1MA VERTICAL -G  
SWITCH,MODE  
SWITCH,SLIDE  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
SWITCH,TACT  
TRANSISTOR  
TRANSISTOR,BIPOLARS  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR,BIPOLARS  
TRANSISTOR  
TRANSISTOR  
CSS-2201A CHANG SHIN 30V DC 0.  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
THVV502GAA POSTECH DC 12 V 5-  
SW601  
SW602  
SW603  
SW604  
SW605  
SW606  
SW607  
SW608  
SW609  
SW610  
SW611  
SW612  
SW613  
SW614  
SW615  
SW616  
SW617  
SW618  
SW619  
SW620  
SW621  
SW901  
Q152  
Q153  
Q155  
Q156  
Q157  
Q159  
Q161  
Q162  
Q163  
Q164  
Q301  
Q302  
Q303  
Q304  
Q305  
Q380  
Q381  
Q382  
Q3G1  
Q402  
Q403  
Q404  
Q405  
Q406  
Q481  
0TR320309AA  
0TR127309AA  
0TR127309AA  
0TR120309AE  
0TR120309AE  
0TR127309AA  
0TR319809AC  
0TR120309AE  
0TR127309AA  
0TR120309AE  
0TR319809AC  
0TR319809AC  
0TR126609AE  
0TR319809AC  
0TR319809AC  
0TR126609AE  
0TR319809AC  
0TR126609AE  
0TR126609AE  
0TR126609AE  
0TR319809AC  
0TR319809AC  
0TR320309AA  
0TR319809AC  
0TR126609AE  
KTC3203 KEC TP TO92 50V 150MA  
KTA1273-TP-Y (KTA966A)KEC  
KTA1273-TP-Y (KTA966A)KEC  
SRC1203 TP AUK TO92 22K,22K  
SRC1203 TP AUK TO92 22K,22K  
KTA1273-TP-Y (KTA966A)KEC  
KTC3198-TP-BL (KTC1815)KEC  
SRC1203 TP AUK TO92 22K,22K  
KTA1273-TP-Y (KTA966A)KEC  
SRC1203 TP AUK TO92 22K,22K  
KTC3198-TP-BL (KTC1815)KEC  
KTC3198-TP-BL (KTC1815)KEC  
KTA1266-GR,TP(KTA1015),KEC  
KTC3198-TP-BL (KTC1815)KEC  
KTC3198-TP-BL (KTC1815)KEC  
KTA1266-GR,TP(KTA1015),KEC  
KTC3198-TP-BL (KTC1815)KEC  
KTA1266-GR,TP(KTA1015),KEC  
KTA1266-GR,TP(KTA1015),KEC  
KTA1266-GR,TP(KTA1015),KEC  
KTC3198-TP-BL (KTC1815)KEC  
KTC3198-TP-BL (KTC1815)KEC  
KTC3203 KEC TP TO92 50V 150MA  
KTC3198-TP-BL (KTC1815)KEC  
KTA1266-GR,TP(KTA1015),KEC  
- 5-12 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MODEL : NTH960  
RUN DATE : 2004.05.01  
S
AL LOCA.NO.  
Q501  
Q502  
Q503  
Q504  
Q506  
Q512  
Q513  
Q514  
Q515  
Q521  
Q901  
Q902  
Q903  
Q904  
Q905  
Q906  
Q907  
Q908  
Q909  
Q910  
Q911  
Q912  
Q913  
Q914  
PART NO  
DESCRIPTION  
TRANSISTOR  
TRANSISTOR,BIPOLARS  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR,BIPOLARS  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR,BIPOLARS  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
SPECIFICATION  
REMARK  
0TR319809AC  
0TR319809AA  
0TR127309AA  
0TR126609AE  
0TR126609AE  
0TR120309AE  
0TR103009AF  
0TR120309AE  
0TR120309AE  
0TR320309AA  
0TR120309AE  
0TR120309AE  
0TR120309AE  
0TR120309AE  
0TR120309AE  
0TR120309AE  
0TR120309AE  
0TR120309AE  
0TR120309AE  
0TR120309AE  
0TR320309AA  
0TR534309BA  
0TR198009CA  
0TR198009CA  
KTC3198-TP-BL (KTC1815)KEC  
KTC3198(KTC1815) KEC TP TO92 5  
KTA1273-TP-Y (KTA966A)KEC  
KTA1266-GR,TP(KTA1015),KEC  
KTA1266-GR,TP(KTA1015),KEC  
SRC1203 TP AUK TO92 22K,22K  
KRA103M(KRA2203) KEC TP TO92M  
SRC1203 TP AUK TO92 22K,22K  
SRC1203 TP AUK TO92 22K,22K  
KTC3203 KEC TP TO92 50V 150MA  
SRC1203 TP AUK TO92 22K,22K  
SRC1203 TP AUK TO92 22K,22K  
SRC1203 TP AUK TO92 22K,22K  
SRC1203 TP AUK TO92 22K,22K  
SRC1203 TP AUK TO92 22K,22K  
SRC1203 TP AUK TO92 22K,22K  
SRC1203 TP AUK TO92 22K,22K  
SRC1203 TP AUK TO92 22K,22K  
SRC1203 TP AUK TO92 22K,22K  
SRC1203 TP AUK TO92 22K,22K  
KTC3203 KEC TP TO92 50V 150MA  
2SC5343-L TP AUK TO92 -  
TRANSISTOR  
TRANSISTOR,BIPOLARS  
TRANSISTOR,BIPOLARS  
TRANSISTOR  
2SA1980G TP AUK TO92  
2SA1980G TP AUK TO92  
TRANSISTOR  
TRANSFORMER  
TRANSFORMER,SMPS[COIL]  
VARISTOR  
VARISTOR,DRAWING  
X-TAL  
T101  
V101  
642-023U  
656-004C  
SJE-023U SJ/CS WIDE EER2828  
SVC681D-10A SAMHWA 4.O CUT  
X302  
X501  
X502  
6202R2357AE  
6202R-DA01A  
6202R1143DC  
RESONATOR,CRYSTAL  
RESONATOR,CRYSTAL  
RESONATOR,CRYSTAL  
ZENER DIODE  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
DIODE,ZENER  
HC49U SSANG TAE 3-579575MHZ 1  
CFS-308 CITIZEN 32-768KHZ 20  
H49U BUBANG 14-31818HZ 25PPM 1  
ZD101  
ZD152  
ZD502  
ZD503  
ZD901  
ZD902  
ZD903  
ZD904  
ZD905  
ZD906  
ZD907  
ZD908  
ZD909  
ZD910  
ZD911  
ZD912  
ZD913  
ZD914  
ZD915  
ZD916  
ZD917  
ZD920  
0DZ332609FA  
0DZ910009BB  
0DZ622609AB  
0DZ622609AB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ132609BB  
0DZ910009BB  
UZ-3.3BSB 26MM TP PYUNG CHANG  
MTZJ9.1C TP ROHM-K DO34 0.5W 8  
UZ-6.2BSA 26MM TP PYUNG CHANG  
UZ-6.2BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
UZ-13BSA 26MM TP PYUNG CHANG  
MTZJ9.1C TP ROHM-K DO34 0.5W 8  
- 5-13 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  

La Crosse Technology Portable Radio Wireless Temperature Station User Manual
Land Pride Tiller RTR15 Series User Manual
Lantronix Network Router 900 422 User Manual
Lasko Fan 754200 User Manual
Line 6 Network Card JM4 User Manual
Makita Impact Driver 6990D User Manual
Makita Impact Driver BTL060 User Manual
M Audio Network Card AP 012403 User Manual
Maytag Clothes Dryer MED3000B User Manual
Metrologic Instruments Scanner MS9520 Voyager User Manual