LG Electronics Laptop LS70 User Manual

Service Manual

(LS70)

LG Electronics

_{Download from Www.Somanuals.co}0_{m. All Manuals Search And Download.}

Ch1. Service information

Chapter 1. Service information

1-1. Important service information

„ Strategy for replacing parts (FRU-Field Replaceable Units)

Before replacing parts

Make sure that latest BIOS and drivers are installed before replacing any parts (FRUs) listed in this

Use the following strategy to prevent unnecessary expense for replacing and servicing parts

1. If you are instructed to replacing a part but the replacement does not correct the problem, reinstall the

original part before you continue.

2. Some computers have both a processor board and system board. If you are instructed to replace either

the processor board or the system board, and replacing one of them does not correct the problem,

reinstall that board, and then replace the other one.

3. If an adapter or device consists of more than one part, any of the parts (FRUs) may be the cause of the

error. Before replacing the adapter or device, remove the parts (FRUs), one by one, to see if the

symptoms change. Replace only the part that changed the symptoms.

Caution

The BIOS configuration on the computer you are servicing may have been customized.

Running Automatic Configuration my alter the settings. Note the current configuration settings;

then, when service has been completed, verify that those settings remain in effect.

„ Strategy for replacing a hard-disk drive

You have to get a User’s approval before formatting or replacing a hard-disk drive. You must let the User

know that the user is responsible for the loss data

Caution

The drive startup sequence in the computer you are servicing may have been changed. Be

extremely careful during write operations such as copying, saving, or formatting. If you select an

incorrect drive, data or programs can be overwritten.

_{Download from Www.Somanuals.co}2_{m. All Manuals Search And Download.}

Ch1. Service information

1-2. Safety notices

Warning

Before the computer is powered-on after part (FRU) replacement, make sure all screws, springs,

and other small parts are in place and are not left loose inside the computer. Verify this by

shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause

electrical shorts.

Warning

some standby batteries contain a small amount of nickel and cadmium. Do not disassemble

a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery

as required by local ordinances or regulations. Use only the battery in the appropriate parts

listing. Use of an incorrect battery can result in ignition or explosion of the battery

Warning

The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or

water, or short-circuit it. Dispose of the battery pack as required by local ordinances or

regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.

Use of an incorrect battery can result in ignition or explosion of the battery.

Warning

If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands,

immediately was the affected areas with water for at least 15 minutes. Seek medical care if any

symptoms from the fluid are present after washing.

Warning

To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card.

Warning

Though the main batteries have low voltage, a shorted or grounded battery can produce enough

current to burn personnel or combustible materials.

Warning

Before removing any part (FRU), turn off the computer, unplug all power cords from electrical

outlets, remove the battery pack, and then disconnect any interconnecting cables.

_{Download from Www.Somanuals.co}3_{m. All Manuals Search And Download.}

Ch1. Service information

1-3. Safety information

„ General safety

Follow these rules to ensure general safety

· Observe good housekeeping in the area of the machines during and after maintenance.

· When lifting any heavy object

1. Ensure you can stand safely without slipping.

2. Distribute the weight of the object equally between your feet.

3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.

4. Lift by standing or by pushing up with your leg muscles

(This action removes the strain from the muscles in your back.)

· Do not attempt to lift any object weights more then 16kg(35lb) or object that you think are too heavy for you.

· Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.

· Before you start the machine, ensure that other service representatives and the customer’s personnel are

not in a hazardous position.

· Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the

machine.

· Keep your tool box away from walk areas so that other people will not trip over it.

· Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your

sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.

· Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, approximately

8 centimeters(3 inches) from the end.

· Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for you clothing.

· Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using

solvents, or working in any other conditions that might be hazardous to your eyes.

· After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that

is worn or defective.

· Reinstall all covers correctly before returning the machine to the customer.

Caution

Metal objects are good electrical conductors.

_{Download from Www.Somanuals.co}4_{m. All Manuals Search And Download.}

Ch1. Service information

„ Electrical safety

Observe the following rules when working on electrical equipment.

Important

Use only approved tools and test equipment. Some hand tools have handles covered with a soft

material that does not insulate you when working with live electrical currents.

Many customers have, near their equipment, rubber floor mats that contain small conductive

fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from

electrical shock.

· Find the room emergency power-off switch, disconnecting switch, or electrical outlet. If an electrical outlet.

If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.

· Do not work alone under hazardous conditions or near equipment that has hazardous voltages.

· Disconnect all power before

1. Performing a mechanical inspection

2. Working near power supplies

3. Removing or installing main units

· Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer

to power-off the wall box that supplies power to the machine and to lock the wall box in the off position.

· If you need to work on a machine that has exposed electrical circuits, observe the following precautions :

Ensure that another person, familiar with the power-off controls, is near you.

Caution

Another person must be there to switch off the power, if necessary.

· Use only one hand when working with powered-on electrical equipment. Keep the other hand in your

pocket or behind your back

Caution

An electrical shock can occur only when there is a complete circuit. By observing the above rule,

you may prevent a current from through your body.

· When using testers, set the controls correctly and use the approved probe leads and accessories for that

tester

_{Download from Www.Somanuals.co}5_{m. All Manuals Search And Download.}

Ch1. Service information

· Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal

floor strips and machine frames.

· Observe the special safety precautions when you work with very high voltages. These instructions are in

the safety sections of maintenance information. Use extreme care when measuring high voltages.

· Regularly inspect and maintain your electrical hand tools for safe operational condition.

· Do not use worn or broken tools and testers.

· Never assume that power has been disconnected from a circuit. First check that it has been powered off.

· Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,

non-grounded power extension cables, power surges, and missing safety grounds.

· Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is

conductive such touching can cause personal injury and machine damage.

· Do not service the following parts with the power on when they are removed from their normal operating

places in a machine.

1. Power supply units

2. Pumps

3. Blowers and fans

4. Motorgenerators

and similar units. (This practice ensure correct grounding of the units.)

· If an electrical accident occurs

1. Use caution ; do not become a victim of yourself.

2. Switch off power.

3. Send another person to get medical aid.

_{Download from Www.Somanuals.co}6_{m. All Manuals Search And Download.}

Ch1. Service information

„ Safety inspection guide

The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions.

As each machine was designed and built, required safety items were installed to protect users and service

personnel from injury. This guide addresses only those items. You should use good judgment to identify

potential safety hazards due to attachment of non-LG features or options not covered by this inspection

guide.

If any unsafe conditions are present, you must determine how serious the apparent hazard could be and

whether you can continue without first correcting the problem.

· Consider these conditions and the safety hazards they present

1. Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal

electrical shock)

2. Mechanical hazards, such as loose or missing hardware

Refer to the following checklist and begin the checks with the power off, and the power cord disconnected.

· Checklist

1. Check exterior covers for damage (loose, broken, or sharp edges)

2. Power off the computer. Disconnect the power cord.

3. Check the power cord for :

a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity

for 0.1 or less between the external ground pin and frame ground.

b. The power cord should be the type specified in the parts list.

c. Insulation must not be frayed or worn.

4. Remove the cover.

5. Check for any obvious non-LG alterations. Use good judgment as to the safety of any non-LG

alterations.

6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or

other liquids, or signs of fire or smoke damage.

7. Check for worn, frayed, or pinched cables.

8. Check that the power-supply cover fasteners (screw or rivets) have not been removed or tampered with.

_{Download from Www.Somanuals.co}7_{m. All Manuals Search And Download.}

Ch1. Service information

„ Handling devices that are sensitive to electrostatic discharge

Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to

electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between

objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat,

and the person handling the part are all at the same charge.

Note

Use product-specific ESD procedures when they exceed the requirements noted here.

Make sure that the ESD protective devices you use have been certified (ISO9000) as fully effective.

· When handling ESD-sensitive parts :

1. Keep the parts in protective packages until they are inserted into the product.

2. Wear a grounded wrist strap against your skin to eliminate static on your body.

3. Prevent the part from touching your clothing. Most clothing retains a charge even when you are wearing

a wrist strap.

4. Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially

useful when handling ESD-sensitive devices.

5. Select a grounding system, such as those listed below, to provide protection that meets the specific

service requirement.

Note

The use of a grounding system is desirable but not required to protect against ESD damage.

a. Attach the ESD ground clip too any frame ground, ground braid, or green-wire ground.

b. Use an ESD ground or reference point when working on a double-insulated or battery-operated

system. You can use coax or connector-outside shells on these systems.

c. Use the round ground-prong of the AC plug on AC-operated computers.

„ Grounding requirements

Electrical grounding of the computers is required for operator safety and correct system function.

Proper grounding of the electrical outlet can be verified by a certified electrician.

_{Download from Www.Somanuals.co}8_{m. All Manuals Search And Download.}

Ch1. Service information

1-4. Laser compliance statement

When a CD-ROM drive, DVD drive or the other laser product is installed, note the following :

Caution

Use of controls or adjustments or performance of procedures other than those specified here in

might result in hazardous radiation exposure.

Opening the CD-ROM drive, DVD-ROM drive or the other optical storage device could result in exposure

to hazardous laser radiation.

There are no serviceable parts inside those drives. Do not open

Danger

Emits visible and invisible laser radiation when open. Do not stare into the beam , do not view

directly with optical instruments, and avoid direct exposure to the bean.

1-5. Backup (Standby) RTC battery safety information

When replacing or disposing of the backup (standby) RTC battery, note the following :

_{Download from Www.Somanuals.co}9_{m. All Manuals Search And Download.}

Ch1. Service information

1-6. Read this first

Before you go to the checkout guide, be sure to read this section.

Important Notes

· Only trained personnel certified by LG should service the computer.

· Read the entire FRU removal and replacement page before replacing any FRU.

· Use new nylon-coated screws when you replace FRUs.

· Be extremely careful during such write operations as copying, saving, formatting.

Drives in the computer that you are servicing sequence might have been altered. If you selected an

incorrect drive, data or programs might be overwritten.

· Replace FRUs only for the correct mode.

· When you replace a FRU, make sure the model of the machine and the FRU part number are correct by

referring to the FRU parts list.

· A FRU should not be replaced because of a single, irreproducible failure. Single failures can occur for a

variety of reasons that have nothing to do with a hard ware defect, such as cosmic radiation,

electrostatic discharge, or software errors.

· Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective, clear the

error log and run the test again. If the error does not recur, do not replace the FRU.

· Be careful not to replace a non-defective FRU.

„ What to do first

You must fill out the record form first.

During the warranty period, the customer may be responsible for repair costs if the computer damage was

caused by misuse, accident, modification, unsuitable physical or operating environment, or improper

maintenance by the customer. The following list provides some common items that are not covered under

warranty and some symptoms that might indicate that the system was subjected to stress beyond normal

use. Before checking problems with computer, determine whether the damage is covered under the

warranty by referring to the following :

_{Download from Www.Somanuals.c}1_om0_{. All Manuals Search And Download.}

Ch1. Service information

The followings are not covered under warranty :

· CD panel cracked from the application of excessive force or from being dropped

· Scratched (cosmetic) parts

· Distortion, deformation, or discoloration of the cosmetic parts

· Cracked or broken plastic parts, broken latches, broken pins, or broken connectors caused by excessive

force

· Damage caused by liquid spilled into system

· Damage caused by improper insertion of a PC Card or the installation of an incompatible card

· Damage caused foreign material in the diskette drive

· Diskette drive damage caused by pressure on the diskette drive cover or by the insertion of a diskette

with multiple labels

· Damaged or bent diskette eject button

· Fusses blown by attachment of a non-supported device

· Forgotten computer password (making the computer unusable)

· Sticky keys caused by spilling a liquid onto the keyboard

The following symptoms might indicate damage caused by non-warranted activities :

· Missing parts might be a symptom of unauthorized service or modification.

· If the spindle of a hard-disk drive becomes noisy, it may have been subjected to excessive force, or

dropped.

_{Download from Www.Somanuals.c}1_om1_{. All Manuals Search And Download.}

Ch2. Locations

Chapter 2. Locations

„ Front view

LCD latch

WLAN Antenna

MUTE

Volume Up

Volume Down

Power switch

LCD

Keyboard

TouchPad

Built-in MIC

TouchPad button

Built-in speaker

_{Download from Www.Somanuals.c}1_om2_{. All Manuals Search And Download.}

Ch2. Locations

„ Rear view

LAN connector

S-VIDEO connector

Modem connector

AC connector

„ Left view

Express Card eject button

Parallel connector

PC Card slot

USB connector

Express Card slot

4-in-1 Card slot

IEEE1394 connector

PC Card eject button

VGA connector

Fan louvers

„ Right view

Security key hole

MIC connector

ODD eject button

Line-in connector

Emergency eject hole

Optical Disk Drive

USB connector

Headphone connector

Security key hole (Kensington Lock)

User can attach a separately purchased chain lock into the security keyhole and connect it to a fixed object

to prevent a notebook theft

Emergency eject hole

Insert a thin and hard pin into this hole, and you can open the disc tray manually.

_{Download from Www.Somanuals.c}1_om3_{. All Manuals Search And Download.}

Ch3. System information

Chapter 3. System information

„ Specification

- CPU

· Dothan 1.6 ~ 2.1 GHz

· μFCBGA

- Main Chipset & Graphic

· Intel 915GM,ICH6-M

· Intel 915PM, ICH6-M, ATI Mobility Radeon X600 VGA Controller

- Memory

· 2SODIMM – Up to 2GB

· DDR2 PC2-3200S/4200S Capable (400/533MHz)

- HDD

· 2.5” 9.5mm 40/60/80GB SATA Type

- Communication

· Modem, Daughter Card Type

· Marvell Yukon PCI-E Gigabit Ethernet Controller on Board

- Wireless LAN Solution

· 802.11bg/abg Mini PCI Type, Quad-band Antenna

- Card Slot

· Express Card Slot

· 4-in-I Card Slot (Memory Stick, Memory Stick Pro, Multi Media Card, SD Card)

- ODD

· Fixed Optical Storage

· DVD-COMBO

- Port

· VGA, 3X USB(2.0), RJ11, RJ45, Headphone-out/SPDIF, Mic-in, AC-in, IEEE1394, S-Video

- Input Devices

· Keyboard : 86Key Keyboard

· Touchpad

- Buttons

· Power, Volume Down, Volume Up, Mute

- Indicator (LED)

· AC-in, Power On, Charge, HDD, Caps Lock, Num Lock, Wireless

- Power

· 90 Watt 19V 4.74A Adapter

- Audio

· C-Media Azalia Audio Codec, Stereo speakers each 0.5/0.8W

- Battery

· 6 Cell 4.8AHr, CYLINDRICAL (Li-Ion)

· 9 Cell 7.2AHr, CYLINDRICAL (Li-Ion)

_{Download from Www.Somanuals.c}1_om4_{. All Manuals Search And Download.}

Ch3. System information

„ System Block Diagram

_{Download from Www.Somanuals.c}1_om5_{. All Manuals Search And Download.}

Ch3. System information

„ Fn key combinations

The following table shows the function of each combination of Fn with a function key.

Function of Fn keys has nothing to do with Operating System.

[Fn] +

[F1]

Description

User-defined Hot key. (Setting is available at OSD)

[F2]

User-defined Hot key. (Setting is available at OSD)

[F3]

User-defined Hot key. (Setting is available at OSD)

[F4]

Force the computer to enter power-saving mode. (ex: system standby and hibernation)

TouchPad Disable (Impossible to use TouchPad) / TouchPad Enable (Possible to use

TouchPad) / TouchPad Auto-Disable (When connecting USB mouse to the computer,

TouchPad is disable) The TouchPad initialization takes 1~2 seconds, so wait for the

Initialization to end before using the TouchPad.

[F5]

[F6]

[F7]

Wireless LAN on / off

When the computer is attached to an external monitor, you can changed the display output

location with [Fn] + [F7] combination. You can switch to and from the three types of display

modes, LCD display only, the external monitor only, or both at the same time.

[F8]

[F9]

Enable/Disable Auto Sound power management (battery mode only).

Enable/Disable Auto Brightness control.

[F10]

System information

[ESC]

[ScrLk]

[Delete]

[Insert]

Maximum power-saving mode. (when OSD is installed)

Number lock

Brightness up

Brightness down

PgUp

PgDn

Home

End

[F12]

Maximum power-saving mode.

_{Download from Www.Somanuals.c}1_om6_{. All Manuals Search And Download.}

Ch3. System information

„ Status indicators

The system status indicators show the status of the computer

1. Caps lock

Caps lock indicator lights up when the Caps lock key is pressed.

When this indicator lights up, you can type capital letters without pressing the Shift key.

2. Num lock

Num lock indicator lights up when the combination of the Fn and Num lock key is pressed.

When this indicator lights up, you can use the embedded numeric keys.

(To use the numeric keys, you must enable the Internal Keypad setting under the Advanced menu in the BIOS

Setup Utility.)

3. Wireless activity indicator

Wireless activity indicator indicates the following.

Off: Wireless LANis off.

Blinking(3-4 Seconds): Searching for Access point for Wireless LAN Connection.

Blinking (short interval): Data is transferring with Wireless LAN is on.

4. AC Power

Power indicator lights up when the power cord is connected to the computer.

5. Power

Power status indicator indicates the following status of the computer.

Green: The computer is turned on.

Off: The computer is turned off or is in hibernation mode.

Blinking: The computer is in standby mode.

6. Battery

Battery status indicator indicates the following status of the battery.

Green: The computer is connected to an AC adaptor and is being charged.

Off: The battery is fully charged OR the computer is not connected to an AC Adapter.

Blinking: The battery power is under 10% of its maximum capacity or battery occurs.

Battery tribe warning blinks as user defined from 'Battery Miser'.

7. Drive in use

Drive in use indicator lights up when data is being written to or read from the hard disk or optical disk drive.

_{Download from Www.Somanuals.c}1_om7_{. All Manuals Search And Download.}

Ch3. System information

„ BIOS Flash

You can update BIOS using a floppy disk drive.

Because this system is not equipped with any floppy disk drive, you have to use an external USB drive for

a BIOS update. In order to boot up with an USB drive, please set Removable Device as the first boot up

drive in the boot menu of BIOS setup.

· How to update flash ROM in DOS

1. Create ‘boot up’ flash update diskette.

2. Copy a ROM image file (*.wph) into the root of the flash update diskette.

3. Copy phlash16.exe to the flash update diskette.

4. Insert the diskette into the FDD of your computer.

5. Boot your computer with the diskette, and type ‘phlash16*.wph/mode=n’.

6. Cold boot and follow the instruction displayed on the screen.

· Flash options /mode=n

0 – Default mode. Keep the current DMI information and update BIOS image only.

1 – Update DMI information only.

If new DMI information is not specified, the current DMI information is left unchanged.

2 – Update BIOS and DMI information.

If new DMI information is not specified, the current DMI information is left unchanged.

3 – Update BIOS and DMI information.

DMI information is updated to the DMI string and options specified in the new BIOS image.

Note

DMI is Desktop Management Interface

_{Download from Www.Somanuals.c}1_om8_{. All Manuals Search And Download.}

Ch3. System information

„ How to update flash ROM in Windows

1. Quit all running programs.

2. Start WINPHLASH.EXE.

3. Select the procedure you want :

a. Backup BIOS and Flash BIOS with new settings

b. Backup BIOS Only

4. Specify the locations for backup and new BIOS files in BIOS Setting Locations.

a. Enter the name of the backup file for existing BIOS or click Browse to locate the file.

b. Enter the name of the new BIOS file or click Browse to locate the file.

5. Click Advanced Settings button to access the advanced settings

6. Click Flash BIOS button to start flash BIOS.

7. Wait for the operation to complete. WinPhlash may take one or two minutes to complete flash BIOS

operation.

_{Download from Www.Somanuals.c}1_om9_{. All Manuals Search And Download.}

Ch3. System information

8. After the completion, ‘System BIOS was successfully updated’ appears on the screen, then the

computer restarts.

9. After the restart, make sure the system BIOS is updated.

10. If your computer does not restart automatically, turn off your computer and then turn it back on by

pressing power button.

_{Download from Www.Somanuals.c}2_om0_{. All Manuals Search And Download.}

Ch3. System information

„ BIOS Setup

BIOS (Basic Input and Output System) Setup saves the system configuration in CMOS RAM, and

check the configurations during startup. Use the BIOS Setup Utility to change and save the system

environment, hardware configurations, power saving mode, etc.

· Open the BIOS Setup Utility in the following situations :

1. to change the BIOS setup

2. to replace the backup battery

3. system configuration error occurs

4. to change the boot order

5. to set/change a password

Press the power button.

When the LG logo appears on the screen, press

and enter the BIOS Setup Utility.

_{Download from Www.Somanuals.c}2_om1_{. All Manuals Search And Download.}

Ch3. System information

„ Using the keys

The keys used in the BIOS Setup Utility and their functions are described at the bottom.

: General Help

Display the descriptions of the keys used in the setup utility.

: Select Item

Navigate and select items in the setup utility. The selected item becomes highlighted.

: Select Menu

Move to another menu.

: Change Values

Change the value of a selected item.

: Load Default Configuration

Display Setup Confirmation window. Press Enter to load default configuration.

: Select Sub-Menu

Some items have sub-menus. Display the sub-menu for a selected item.

: Save and Exit

Display Setup Confirmation window. Press Enter to save and exit.

: Exit

In a sub-menu, press Esc to move to the previous window. In Main menu, click Esc to move to Exit menu.

_{Download from Www.Somanuals.c}2_om2_{. All Manuals Search And Download.}

Ch3. System information

„ Main menu

System Time

Current time. Use <Tab>, <Shift-Tab>, or <Enter> keys to move around these fields. To change the

value, press <+> or <−> key.

System Date

Today date. Use <Tab>, <Shift-Tab>, or <Enter> keys to move around these fields. To change the value,

press <+> or <−> key. Set any date from year 1981 to 2079. It will automatically keep track of leap years.

The system date can also be set from the operating system.

Product Name

This shows the name of PC.

Processor Type

This shows the type of CPU.

Processor Spd

This shows the speed CPU.

BIOS Version

This shows the Version of BIOS.

KBC Version

This shows the Version of KBD firm ware.

UUID

This is for display only. This shows the UUID.

Pri Master

Enter its submenu by pressing <Enter>. In this submenu, it would show the device of Primary IDE Master

is HDD and its parameters.

Pri Slave

Enter its submenu by pressing <Enter>. In this submenu, it would show the device of Primary IDE Slave

is HDD and its parameters.

Sec Master

Enter its submenu by pressing <Enter>. In this submenu, it would show the device of Secondary IDE

Master is optical drive and its parameters.

Sec Slave

Enter its submenu by pressing <Enter>. In this submenu, it would show the device of Secondary IDE

Slave is optical drive and its parameters.

System Memory

This is for display only. This shows size of system memory.

Ext. Memory

This is for display only. This shows size of extended memory.

_{Download from Www.Somanuals.c}2_om3_{. All Manuals Search And Download.}

Ch3. System information

„ Advanced menu

Legacy USB Support

There are two options to this field: Enabled, and Disabled. This field allows you to enable or disable the

legacy USB support.

Boot-time Diagnostic Screen

Enables the Boot-time Diagnostic Screen.

SATA Controller Mode

Set SATA (Serial ATA) Controller Mode.

AHCI Configuration

Enables the AHCI (Advanced Host Controller Interface).

Battery Charge Stop Percentage

Set Battery Charge Stop Percentage.

Fan Mode Control

Set Fan Mode Control.

Fn Key Setup

Set Sticky fn key function.

Wake On Lan

Enables Wake On Lan.

PXE/Remote Boot

Enables PXE/Remote Boot.

Execute-Disable Bit Capability

Enables Execute-Disable Bit Capability.

„ Security menu

Supervisor Password Is

This shows the system’s supervisor password has been set, or not.

Set Supervisor Password

Set Supervisor Password.

User Password Is

This shows the system’s User Password has been set, or not.

Set User Password

Set User Password.

Password on boot

Enables Password on boot.

HDD Password Is

This shows the system’s HDD Password has been set, or not.

Set HDD Password

Set HDD Password.

_{Download from Www.Somanuals.c}2_om4_{. All Manuals Search And Download.}

Ch3. System information

„ Boot menu

Boot menu enables you to set the boot order for the CD-ROM drive, Removable devices Hard drive,

and Network boot as shown below.

CD-ROM Drive

Removable Devices

Hard Drive

B2 D0 Yukon PXE

„ Exit menu

Exit Saving Changes

Select Exit Saving Changes to save new setup information in CMOS RAM. CMOS RAM stores the

information using the backup battery; therefore, the information will not be lost when the computer is

turned off.

Exit Discarding Changes

Select Exit Discarding Changes to discard new setup information. If you made changes to items other

than date, time, and passwords, the Setup Warning asks you to save the new configurations. Select Yes

and press Enter to save the new configuration.

Load Setup Defaults

Select Load Setup Defaults to change the setup information to the factory default settings. If you select

Load Setup Defaults or press F9, Setup Confirmation asks you to confirm your selection. Press Yes to

load setup defaults.

Discard Changes

Discard change value.

Save Changes

Save change value.

_{Download from Www.Somanuals.c}2_om5_{. All Manuals Search And Download.}

Ch4. Symptom-to-part index

Chapter 4. Symptom-to-part index

The symptom-to-part index in this section lists symptoms and errors and their possible causes.

The most likely cause is listed first.

Note

If replacing a part (FRU) does not solve the problem, put the original part back in the computer.

Do not replace a non-defective FRU.

„ Power system checkout

· To verify a symptom, do the following :

1. Power off the computer.

2. Remove the battery pack.

3. Connect the AC adapter.

4. Check that power is supplied when you power on the computer.

5. Power off the computer.

6. Disconnect the AC adapter and install the charged battery pack.

7. Check that the battery pack supplies power when you power on the computer.

· If you suspect a power problem, see the appropriate one of the following power supply checkouts :

1. Checking the AC adapter

2. Checking the operational charging

3. Checking the battery pack

4. Checking the backup battery

· Checking the AC adapter

If the power-on indicator does not turn on, check the power cord of the AC adapter for correct continuity

and installation.

If the computer does not charge during operation, go to “Checking operational charging.”

To check the AC adapter, do the following :

Voltage (V dc)

+18.05 ~ +19.95

Ground

1. Unplug the AC adapter cable from the computer.

2. Measure the output voltage at the plug of the

AC adapter cable. See the following figure :

_{Download from Www.Somanuals.c}2_om6_{. All Manuals Search And Download.}

Ch4. Symptom-to-part index

· If the voltage is not correct, replace the AC adapter.

· If the voltage is acceptable, do the following :

1. Replace the system board.

2. If the problem persists, check the AC adapter whether it is correct product or not.

Note

Noise from the AC adapter does not always indicate a defect.

· Checking operational charging

1. To check whether the battery charges properly during operation, use a discharged battery pack or a

battery pack that has less than 50% of the total power remaining when installed in the computer.

Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery

does not turn on, replace the battery pack.

2. If the charge indicator still does not turn on, replace the system board.

Then reinstall the battery pack.

Note

Do not charge battery pack, when its temperature is below 0 or above 75

· Checking the battery pack

1. Open the Power Meter window by clicking Start Control Panel Power Options and then;

check the total power remains. Battery charging does not start until the power Meter shows that less

than 95% of the total power remains; under this condition the battery pack can charge to 100% of its

capacity. This protects the battery pack from being overcharged or from having a shortened life.

2. To check the status of your batter, move your cursor to the Power Meter icon in the icon tray of the

Windows taskbar and wait for a moment (but do not click), and the percentage of battery power

remaining is displayed. To get detailed information about the battery, double-click the Power Meter icon.

Note

If the battery pack becomes hot, it may not be able to charge. Remove it from the computer and

Leave it at room temperature for a while. After it cools down, reinstall and recharge it.

_{Download from Www.Somanuals.c}2_om7_{. All Manuals Search And Download.}

Ch4. Symptom-to-part index

· The Characteristics of the battery pack

1. Self-discharge

The battery gradually loses its power over time without ever being used.

2. Periodic full discharge / charge

Frequent recharge of the battery pack can reduce the capacity of the battery pack. When this happens,

you can perform the full discharge / charge to improve the capacity. You should perform periodic full

discharge /charge once every 30~60 days.

You should always use the battery until its power is low; then fully charge the battery.

3. Trickle charge

If the temperature of the battery pack drops below 10 , the trickle charging begins.

The trickle charging may take 32 hours for the battery pack to be fully charged.

_{Download from Www.Somanuals.c}2_om8_{. All Manuals Search And Download.}

Ch4. Symptom-to-part index

· To check the battery pack, do the following :

1. Power off the computer.

2. Remove the battery pack and measure the voltage between battery terminals 1(-) and 5(+).

See the following figure :

Terminal

Voltage (V dc)

Ground(-)

+0V ~ +12.6V

(6 cell)

5(+)

1(-)

3. If the voltage is still less than +11.1 V DC after recharging, replace the battery.

4. If the voltage is more than +11.1 V DC, measure the resistance between battery terminals 1 and 2.

The resistance must be 2 to 4 (typically 3 ).

5. If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system

board.

Note

Charging will take at least 3 hours.

Note

Battery is an expendable supplier, so its capacity and used time can be reduced by using the computer.

_{Download from Www.Somanuals.c}2_om9_{. All Manuals Search And Download.}

Ch4. Symptom-to-part index

„ Numeric error codes

Symptom / Error

FRU or action, in sequence

1.Reset the hard-disk drive.

0200

Fixed disk failure

(The hard disk is not working)

2.Load Setup Defaults in BIOS Setup Utility.

3.Hard-disk drive.

4.System board.

0210

Stuck Key error

1.Check the keyboard if it is pressed.

2.Replace the keyboard.

0211

Keyboard error

Run interactive tests of the keyboard and the auxiliary

input device.

0212

System board.

Keyboard Controller Failed

0220

Load Setup Defaults in BIOS Setup Utility.

Monitor type error - Monitor type does not

match the one specified in CMOS.

0230

1.DIMM

System RAM error - System RAM Failed at

offset.

2.System board

0231

System board

Shadow RAM error - Shadow RAM failed at

offset

0232

1. DIMM

Extended RAM error - Extended RAM Failed

at address line

2. System board

0250

Replace the backup battery and run BIOS Setup Utility

to reset the time and date.

System battery error – System battery is dead

_{Download from Www.Somanuals.c}3_om0_{. All Manuals Search And Download.}

Ch4. Symptom-to-part index

Symptom / Error

FRU or action, in sequence

0251

Replace the backup battery and run BIOS Setup Utility

to reset the time and date.

System CMOS checksum bad

– System CMOS checksum is not correct.

– Default configuration used.

0252

Reset the password by running BIOS Setup Utility.

Password checksum bad – The password is

cleared.

0260

System timer error

1. Replace the backup battery and run BIOS

Setup Utility to reset the time and date.

2. System board.

0271

Run BIOS Setup Utility to reset the time and date.

Check date and time settings – Date and time

error.

0280

1. Load “Setup Default” in BIOS Setup Utility.

2. DIMM.

3. System board.

Previous boot incomplete

- Default configuration used

0281: Memory Size found by POST differed

from EISA CMOS

Load Setup Defaults in BIOS Setup Utility.

Set up the diskette type in BIOS Setup Utility.

02B0

Diskette drive A error

02B1

Diskette drive B error

02B2

1. Floppy diskette drive.

2. External FDD cable.

3. I/O card.

Incorrect drive A type – Floppy diskette drive

error

02B3

1. Floppy diskette drive.

2. External FDD cable.

3. I/O card.

Incorrect Drive B type

02D0

1. Load “Setup Default” in BIOS Setup Utility.

2. System board.

System cache error – Cache disabled

(RAM cache failed and BIOS disabled)

02F4

1. Load “Setup Default” in BIOS Setup Utility.

2. Replace the backup battery.

3. System board.

EISA CMOS not writable

02F5

1. DIMM

DMA test failed

2. System board

02F6

1. DIMM

Software NMI failed

2. System board

_{Download from Www.Somanuals.c}3_om1_{. All Manuals Search And Download.}

Ch4. Symptom-to-part index

Symptom / Error

FRU or action, in sequence

02F7

1. DIMM

Fail – Safe timer NMI failed

2. System board

0611

1. Load Setup Defaults in BIOS Setup Utility.

2. System board.

IDE configuration changed

0612

1. Load Setup Defaults in BIOS Setup Utility.

2. System board.

IDE configuration error

0613

1. Load Setup Defaults in BIOS Setup Utility.

2. System board.

Com A configuration changed

0614

1. Load Setup Defaults in BIOS Setup Utility.

2. System board.

Com A configuration error

0615

1. Load Setup Defaults in BIOS Setup Utility.

2. System board.

Com B configuration changed

0616

1. Load Setup Defaults in BIOS Setup Utility.

2. System board.

Com B configuration error

0617

1. Load Setup Defaults in BIOS Setup Utility.

2. System board.

Floppy configuration changed

0618

1. Load Setup Defaults in BIOS Setup Utility.

2. System board.

Floppy configuration error

0619

1. Load Setup Defaults in BIOS Setup Utility.

2. System board.

Parallel port configuration changed

061A

1. Load Setup Defaults in BIOS Setup Utility.

2. System board.

Parallel port configuration error

_{Download from Www.Somanuals.c}3_om2_{. All Manuals Search And Download.}

Ch4. Symptom-to-part index

„ Error message

Symptom / Error

FRU or action, in sequence

Device address conflict.

1. Load Setup Defaults in BIOS Setup Utility.

2. Backup battery.

3. System board.

Allocation error for device.

1. Load Setup Defaults in BIOS Setup Utility.

2. Backup battery.

3. System board.

Failing bits: nnnn.

1. DIMM.

2. System board.

Invalid System Configuration Data.

I/O Device IRQ Conflict.

1. DIMM.

2. System board.

1. Load Setup Defaults in BIOS Setup Utility.

2. Backup battery.

3. System board.

Operating System not found.

1. Check that the operating system has no failure and

is installed correctly.

2. Enter BIOS Setup Utility and see whether the hard

-disk drive and the diskette drive are properly

identified.

3. Reset the hard-disk drive.

4. Reinstall the operating system.

5. Diskette drive.

6. Hard-disk drive.

7. System board.

Hibernation error.

1. Restore the system configuration to what it was

before the computer entered hibernation mode.

2. If memory size has been changed, re-create the

hibernation file.

FAN error.

Fan.

Thermal sensing error.

System board.

_{Download from Www.Somanuals.c}3_om3_{. All Manuals Search And Download.}

Ch4. Symptom-to-part index

„ LCD-related symptoms

Note

Before removing or disassembling LCD, power off the computer, unplug all power cords from electrical

outlets, remove the battery pack also.

Symptom / Error

FRU or action, in sequence

Check out Battery Miser.

LCD screen becomes dark suddenly.

Nothing displayed on LCD screen.

1. Check out Battery Miser.

2. Choose Never in the Turn off Monitor item on

Power Options Properties.

3. Check the power save mode switch if it is pressed

by something.

4. Check the System is in standby or hibernation

mode.

LCD backlight not working.

LCD too dark.

1. Reconnect inverter to the board connector.

2. Replace inverter.

LCD brightness cannot be adjusted.

3. LCD assembly.

4. System board.

LCD color cannot be adjusted.

LCD screen abnormal.

Characters missing pixels.

LCD screen unreadable.

Wrong color displayed.

1. Reset all LCD connectors.

2. Replace LCD cable.

3. LCD assembly.

4. System board.

Horizontal or vertical lines displayed

on LCD

LCD assembly.

Power-on indicator on, and a blank\LCD

during POST.

LCD assembly.

System board.

_{Download from Www.Somanuals.c}3_om4_{. All Manuals Search And Download.}

Ch4. Symptom-to-part index

„ Indeterminate problems

· You are here because the diagnostic tests did not identify which adapter or device failed, wrong devices

are installed, a short circuit is suspected, or the system is inoperative.

Follow these procedures to isolate the failing FRU (do not isolate FRUs that have no defects).

· Verify that all attached devices are supported by the computer.

· Verify that the power supply being used at the time of the failure is operating correctly.

1. Power off the computer

2. Visually check each FRU for damage. Replace any damaged FRU.

3. Remove or disconnected all of the following devices :

a. Non-LG devices.

b. Printer, mouse, and other external devices.

c. Battery pack.

d. PC cards.

e. ODD (CD-ROM, Combo) drive or FDD drive in the Bay.

f. Hard-disk drive.

Note

Use the other memory card because it needs when operating computer.

4. Power on the computer.

5. Determine whether the problem has changed.

6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.

7. If the problem remains, replace the following FRUs one at a time.

(do not replace a non-defective FRU)

a. LCD assembly (Check external monitor whether the same problem recurs or not).

b. Keyboard.

c. Keydeck (TouchPad and Scroll Button assembly).

d. System board.

_{Download from Www.Somanuals.c}3_om5_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

Chapter 5. Removing and replacing a part (FRU)

Danger

Before removing any FRU, power off the computer, unplug all power cords from electrical

outlets, remove the battery pack, and then disconnect any interconnecting cables.

Caution

Before the computer is powered on after FRU replacement, make sure that all screws, springs,

and other small parts are in place and are not loose inside the computer. Verify metal flakes can

cause electrical short circuits.

Note

As for the screw, every Torque 3 0.2Kgfcm(0.196Nm)

_{Download from Www.Somanuals.c}3_om6_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1010 Battery Pack

1. Push the battery latch in the direction shown below; then side the battery pack out of the slot.

_{Download from Www.Somanuals.c}3_om7_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1020 Hard Disk Drive

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Battery Pack(1010)

1. Remove a screw as indicated in the picture, then pull the HDD Assy out in the direction shown below.

No.

FRU No.

Specification

M2.5 X L3.5

Qty

1SZZBA4063B

_{Download from Www.Somanuals.c}3_om8_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1030 Wireless LAN Card

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. Keyboard(1030)

1. Remove 3 Memory Cover screws.

No.

FRU No.

Specification

M2.5 X L3.5

Qty

1SZZBA4063A

2. Remove WLAN Card Antenna cable. Remove WLAN Card.

_{Download from Www.Somanuals.c}3_om9_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1040 Keyboard

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. W/L LAN Card(1030)

1. Remove 2 screws.

No.

FRU No.

Specification

M2.5 X L6.5

Qty

1SZZBA4097A

2. To remove 3 hooks, insert a (-) type screwdriver into a hook located at the lower end of keyboard,

and pull it up.

_{Download from Www.Somanuals.c}4_om0_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

3. Disconnect Keyboard Connector and remove Keyboard.

_{Download from Www.Somanuals.c}4_om1_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1050 Retainer

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. W/L LAN Card(1030) 4. Keyboard(1040)

1. Remove 2 screws.

No.

FRU No.

Specification

M2.5 X L6.5

Qty

1SZZBA4097A

2. To remove Retainer, insert a (-) type screwdriver into a hook located at the lower end of keyboard,

and pull it up.

_{Download from Www.Somanuals.c}4_om2_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

3. Disconnect Retainer Connector and remove Retainer.

_{Download from Www.Somanuals.c}4_om3_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1060 Keyboard Plate

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. W/L LAN Card(1030) 4. Keyboard(1040)

5. Retainer(1050)

1. Remove 7 screws and remove Keyboard Plate.

No.

FRU No.

Specification

M2.0 X L3.5

Qty

1SZZBA4023A

_{Download from Www.Somanuals.c}4_om4_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1070 FAN Assembly

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. W/L LAN Card(1030) 4. Keyboard(1040)

5. Retainer(1050) 6. Keyboard plate(1060)

1. Remove 4 screws and remove Fan Module.

No.

FRU No.

Specification

M2.0 X L10.0

M2.0 X L5.0

Qty

1SZZBZ4020A

1SZZBZ4014A

_{Download from Www.Somanuals.c}4_om5_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1080 Hinge Cover

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. W/L LAN Card(1030) 4. Keyboard(1040)

5. Retainer(1050) 6. Keyboard plate(1060) 7. Keyboard plate(1070)

1. Using a screw driver, remove Hinge Cover. (Left / Right)

_{Download from Www.Somanuals.c}4_om6_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1090 Display Module

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. W/L LAN Card(1030) 4. Keyboard(1040)

5. Retainer(1050) 6. Keyboard plate(1060) 7. Keyboard plate(1070) 8. Hinge Cover(1080)

1. Remove 2 screws.

No.

FRU No.

Specification

M2.5 X L8.0

Qty

1SZZBA4039B

2. Remove 2 screws.

No.

FRU No.

Specification

M2.5 X L6.5

Qty

1SZZBA4097A

_{Download from Www.Somanuals.c}4_om7_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

3. Remove Display Module.

_{Download from Www.Somanuals.c}4_om8_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 110 0 Key Deck

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. W/L LAN Card(1030) 4. Keyboard(1040)

5. Retainer(1050) 6. Keyboard plate(1060) 7. Keyboard plate(1070) 8. Hinge Cover(1080)

9. Display Module(1090)

1. Remove 14 screws.

No.

FRU No.

Specification

M2.5 X L6.5

M2.5 X L8.0

M2.0 X L3.0

Qty

1SZZBA4097A

1SZZBA4039B

1SZZBA4017A

_{Download from Www.Somanuals.c}4_om9_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

3. Remove 4 screws from Key Deck. Disconnect TouchPad cable and speaker cable.

No.

FRU No.

Specification

M2.0 X L5.0

Qty

1SZZBZ4014A

_{Download from Www.Somanuals.c}5_om0_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1110 Optical Disk Drive

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. W/L LAN Card(1030) 4. Keyboard(1040)

5. Retainer(1050) 6. Keyboard plate(1060) 7. Keyboard plate(1070) 8. Hinge Cover(1080)

9. Display Module(1090) 10. Display Module(1100)

1. Insert a screwdriver into the hole located at the rear of ODD and push it out.

_{Download from Www.Somanuals.c}5_om1_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1120 Audio Board

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. W/L LAN Card(1030) 4. Keyboard(1040)

5. Retainer(1050) 6. Keyboard plate(1060) 7. Keyboard plate(1070) 8. Hinge Cover(1080)

9. Display Module(1090) 10. Display Module(1100) 11. Optical Disk Drive(1110)

1. Remove 2 screws. Disconnect Audio connector and remove Audio Board.

No.

FRU No.

Specification

M2.0 X L3.5

Qty

1SZZBA4023A

_{Download from Www.Somanuals.c}5_om2_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1130 HDD Cover Block (L)

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. W/L LAN Card(1030) 4. Keyboard(1040)

5. Retainer(1050) 6. Keyboard plate(1060) 7. Keyboard plate(1070) 8. Hinge Cover(1080)

9. Display Module(1090) 10. Display Module(1100) 11. Optical Disk Drive(1110)

12. Audio Board(1120)

1. Remove HDD Cover Block as indicated in the picture.

_{Download from Www.Somanuals.c}5_om3_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1140 Hinge Frame (L)

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. W/L LAN Card(1030) 4. Keyboard(1040)

5. Retainer(1050) 6. Keyboard plate(1060) 7. Keyboard plate(1070) 8. Hinge Cover(1080)

9. Display Module(1090) 10. Display Module(1100) 11. Optical Disk Drive(1110)

12. Audio Board(1120) 13. HDD Cover Block(1130)

1. Remove 2 screws. Remove Hinge Frame (Left).

No.

FRU No.

Specification

M2.0 X L5.0

Qty

1SZZBZ4014A

_{Download from Www.Somanuals.c}5_om4_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1150 Main Board

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. W/L LAN Card(1030) 4. Keyboard(1040)

5. Retainer(1050) 6. Keyboard plate(1060) 7. Keyboard plate(1070) 8. Hinge Cover(1080)

9. Display Module(1090) 10. Display Module(1100) 11. Optical Disk Drive(1110)

12. Audio Board(1120) 13. HDD Cover Block(1130) 14. Hinge Frame (L)(1140)

1. Remove 3 screws. Disconnect RTC Battery and S-VIDEO connector. Remove Main Board.

No.

FRU No.

Specification

M2.0 X L3.5

Qty

1SZZBA4023A

_{Download from Www.Somanuals.c}5_om5_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

_{Download from Www.Somanuals.c}5_om6_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

_{Download from Www.Somanuals.c}5_om7_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1150 S-Video Board

Remove the following parts in order before replacing this part

1. Battery Pack(1010) 2. Hard Disk Drive(1020) 3. W/L LAN Card(1030) 4. Keyboard(1040)

5. Retainer(1050) 6. Keyboard plate(1060) 7. Keyboard plate(1070) 8. Hinge Cover(1080)

9. Display Module(1090) 10. Display Module(1100) 11. Optical Disk Drive(1110)

12. Audio Board(1120) 13. HDD Cover Block(1130) 14. Hinge Frame (L)(1140) 14. Main

Board(1150)

1. Remove RTC BATT and S-VIDEO Board.

No.

FRU No.

Specification

M2.0 X L5.0

M2.0 X L3.5

Qty

1SZZBZ4014A

1SZZBA4023A

_{Download from Www.Somanuals.c}5_om8_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

■ 1100 Display Module

Remove the following parts in order before replacing this part

1. Using a knife, remove the logo and rubbers that are covering the screws.

Then remove all 6 screws.

No.

FRU No.

Specification

M2.5 X L4.5

Qty

1SZZBA4080F

_{Download from Www.Somanuals.c}5_om9_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

2. Disassemble the LCD front. The front hook located on the middle of LCD upper and lower end.

Be careful of the direction when removing because it is connected from inside out.

_{Download from Www.Somanuals.c}6_om0_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

3. Remove 5 screws and disconnect Inverter Cable.

1 1

No.

FRU No.

Specification

Qty

1SZZBA4080F

1SZZBZ3002W

M2.5 X L4.5

M2.5 X L3.5

_{Download from Www.Somanuals.c}6_om1_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

4. Remove WLAN Antenna Cable. Press the hook on the both side of LCD with a (-) type screwdriver

and remove from the LCD rear panel.

_{Download from Www.Somanuals.c}6_om2_{. All Manuals Search And Download.}

Ch5. Removing and replacing a part

5. Remove 6 screws. Remove LCD from the LCD rear panel.

No.

FRU No.

Specification

M2.5 X L4.5

M2.0 X L3.0

Qty

1SZZBA4080F

1SZZBA4017A

_{Download from Www.Somanuals.c}6_om3_{. All Manuals Search And Download.}

Ch6. Part lists

Chapter 6. Part lists

2005-01-31

HTF05

Location

HFL01

Part Number

Specification

Remarks

6304FLP080A

LP150E06-A2 LG PHILPS TFT COLOR 15.0 INCH SXGA+(1400X1050) ISP STYLE B

WVA

LCD 단품

HFL01

6304FLP081B

6304FHS008A

LP150E06-A3 LG PHILPS TFT COLOR 15.0 INCH SXGA+(1400X1050) ISP STYLE B

WVA P3 PLANT

LCD 단품

HSD150PK17-A00 HANNSTAR TFT COLOR 15.0 INCH SXGA+(1400X1050) WVA ISP

STYLE B

HFL02

HFL03

3111B0TS53A

3300BP1079A

HUNTER-FULL 15 INCH COVER REAR ASSY

PLATE, DISPLAY REAR HUNTER 150 FULL .

REAR CASE

PLATE

DISPLAY

HFL04

HFL05

HFL06

4940BM4166A

4970BW4556A

3111B0TS24A

Knob, latch

KNOB

Spring, Latch

SPRING

Case Assy, Front 15.0"

FRONT

CASE

HFL07

HFL08

4774BD2005A

4774BD2006A

Hinge Ass'y-L

Hinge Ass'y,-R

HINGE LEFT

HINGE

RIGHT

HFL09

HFL10

HFL11

3300BP4455A

3301B00540A

3301B00541A

Plate, Inverter

Inverter Plate

Antenna Left

Plate, antenna-L (620mm)

Plate, antenna-R (800mm)

Antenna

Right

HFL12

HFL13

6708BI0088A

6708BI0089A

4850BM4029A

KUBNKM095A ALPS INVERTER

Inverter

DAC-08B073 DELTA HUNTER-TL 15 INCH OZ1060S

Cushion, rubber-upper

Cushipn

upper

HFL14

HFL15

4826BZ4003B

4850BM4030A

Cushion, rubber-middle

Cushion, rubber-lower

Cushion

Middle

Cushion

Bottom

HFL16

HFL17

HFL18

HFB01

6851B34028A

6851B34032A

6851B34029A

6851B34033A

3850BB3042A

3858BP4273A

3858BZ4462A

6871BH700A1

LCD Cable Assy(XGA),Tae-yang

LCD Cable Assy(XGA), Washin

LCD Cable Assy(SXGA),Tae-yang

LCD Cable Assy(SXGA), Washin

Label, front brand name label

Logo Badge (X-Note)

LCD Cable

Logo Lable

BADGE

Logo Badge (LG)

BADGE

HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A) PP MAIN B/D

ASSY(PM128+GB)

M/B Assy

_{Download from Www.Somanuals.c}6_om4_{. All Manuals Search And Download.}

Ch6. Part lists

Location

HFB01

NMEM1

Part Number

6871BH710A1

6871BH720A1

6871BH730A1

6871BH740A1

0IMMRIH046A

Specification

Remarks

M/B Assy

Memory

HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A) PP MAIN B/D ASSY(PM64+GB)

HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A) PP MAIN B/D ASSY(PM64+FE)

HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A) PP MAIN B/D ASSY(GM+GB)

HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A) PP MAIN B/D ASSY(GM+FE)

HYS64T32000HDL-5-A INFINEON 200P SODIMM BK 256MB 32MX64 400MHZ DDR2

SDRAM WITH 32MX16

NMEM1

0IMMRHY061A

0IMMRSS113A

0IMMRIH047A

0IMMRHY062A

0IMMRSS114A

0IMMR00007A

GIMMR00007A

0IMMR00005A

0IMMR00008A

GIMMR00008A

0IMMR00006A

HYMP532S646-E3 HYNIX 200P SODIMM BK 256MB 32MX64 400MHZ DDR2 SDRAM

WITH 32MX16

Memory

M470T3354BG0-CCC SAMSUNG ELECTRONICS 200P SODIMM BK 256MB 32MX64

400MHZ DDR2 SDRAM WITH 32MX16

HYS64T64020HDL-5-A INFINEON 200P SODIMM BK 512MB 64MX64 400MHZ DDR2

SDRAM WITH 32MX16

HYMP564S646-E3 HYNIX 200P SODIMM BK 512MB 64MX64 400MHZ DDR2 SDRAM

WITH 32MX16

M470T6554BG0-CCC SAMSUNG ELECTRONICS 200P SODIMM BK 512MB 64MX64

400MHZ DDR2 SDRAM WITH 32MX16

HYS64T32000HDL-3.7-A INFINEON 200P SODIMM BK 256MB 32MX64 533MHZ

DDR2 SDRAM WITH 32MX16

HYS64T32000HDL-3.7-A INFINEON 200P SODIMM BK 256MB 32MX64 533MHZ

DDR2 SDRAM WITH 32MX16

M470T3354BZ0-LD5 SAMSUNG ELECTRONICS 200P SODIMM BK 256MB 32MX64

533MHZ DDR2 SDRAM WITH 32MX16

HYS64T64020HDL-3.7-A INFINEON 200P SODIMM BK 512MB 64MX64 533MHZ

DDR2 SDRAM WITH 32MX16

HYS64T64020HDL-3.7-A INFINEON 200P SODIMM BK 512MB 64MX64 533MHZ

DDR2 SDRAM WITH 32MX16

M470T6554BZ0-LD5 SAMSUNG ELECTRONICS 200P SODIMM BK 512MB 64MX64

533MHZ DDR2 SDRAM WITH 32MX16

HTA04

2020B00030A

2026B00007A

GCC-4243N HLDS 8X 24X 24X 24X 12.7MM W/COMMON BEZEL FOR BRAND

ODD 단품

GSA-4080N HLDS 8X 24X 2X 2X 4X 4X 4X 16X 10X 24X NOTE BOOK 12.7MM

COMMON TYPE FOR BRAND

ODD 단품

HTA04

2020B00033A

DW-224E-B88 TEAC 8X 24X 24X 24X 12.7MM W-COMMON BEZEL FOR BRAND NB-

ODD 단품

_{Download from Www.Somanuals.c}6_om5_{. All Manuals Search And Download.}

Ch6. Part lists

Location

HTA04

Part Number

Specification

Remarks

2026B00009A

DV-W28E-588 TEAC 8X 24X 2X 2X 4X 4X 4X 16X 10X 24X NOTE BOOK 12.7MM

W/COMMON BEZEL FOR BRAN NB-PC

ODD 단품

HTA05

HTA06

3300BP4459A

1SZZBA4041A

PLATE, ODD SUPPORT HUNTER 15.4 WIDE .

ODD

SUPPORT

PLATE

+ D3.5 L3.0MM SWRH4 DUMMY COVER FIX SILVER MAGELLAN DISPLAY

PLATE

SCREW

HTA03

HTA01

6744C00085A

6744C00122A

6744C00086A

6744C00106A

6744C00087A

6744C00107A

6744C00123A

6744C00116A

6744C00117A

4811B00605A

MHT2040AT PL FUJITSU 40GB EIDE INNER ZEBRA/MACKINLEY/K2

HTS424040M9AT00 HGST 40GB EIDE INNER MCKINLY 4200RPM

MHT2060AT PL FUJITSU 60GB EIDE INNER ZEBRA/MCKINLEY/K2

IC25N060ATMR04-0 HGST 60GB EIDE INNER MCKINLEY/K2 4200RPM

MHT2080AT PL FUJITSU 80GB EIDE INNER ZEBRA/MCKINLEY/K2

IC25N080ATMR04-0 HGST 80GB EIDE INNER MCKINLEY/K2 4200RPM

MHV2100AT FUJITSU 100GB EIDE INNER HUNTER-S 4200RPM

MHT2060BH FUJITSU 60GB SATA INNER HUNTER

HDD 단품

MHT2080BH FUJITSU 80GB SATA INNER HUNTER

HUNTER-WIDE 15.4 INCH HDD SUS 17.1W, 15F

HDD PLATE

ASSY

HTA02

HFC04

1SZZBA4011A

6871BZT14AC

+ D3.0 L 3.0 SWRH4 HDD WH [S-PJT] #1 TIP

HDD SCREW

Wireless LAN

WM3B2200BGMW2 INTEL 4 LAYERS REV 1.2 PRO/WIRELESS 2200BG LAN MINI-

PCI TYPE CH 1-11 NETWORK CONNECTIO

HFC04

HTC05

6871BZT14AD

6871BZT14AE

6871BZT14AF

6871BZT14AG

6871BG867ZB

WM3B2200BGRW3 INTEL 4 LAYERS REV 1.2 PRO/WIRELESS 2200BG LAN MINI-

PCI TYPE CH 1-14 NETWORK CONNECTIO

Wireless LAN

MDC Assy

WM3B2915ABGNA INTEL 4 LAYERS REV 2.0 CH 1-11 NETWORK CONNECTION

MINIPCI TYPE IIIB STANDARD

WM3B2915ABGEU INTEL 4 LAYERS REV 2.0 CH 1-13 NETWORK CONNECTION

MINIPCI TYPE IIIB STANDARD

WM3B2915ABGRW INTEL 4 LAYERS REV 2.0 CH 1-13 NETWORK CONNECTION

MINIPCI TYPE IIIB STANDARD

T60M893T00 FOXCONN 2 LAYERS REV 0.0 MDC1.5 FORM FACTOR INTERNAL

56K MDC MODEM

HTC05

HTA07

6871BG869ZB

6911B00096A

6911B00119A

6911B00121A

MA560-3 QCOM 2 LAYERS 1A MDC1.5 FORM FACTOR V.92 MODEM CARD

4800MAH 3S-2P SIMPLO LI-ION CYLINDERICAL HUNTER-ALL CELL SDI

4800 mAh 3S-2P Simplo Li-Ion Cylindrical Hunter All SDI cell

MDC Assy

Battery

4800 mAh 3S-2P Simplo Li-Ion Cylindrical Hunter All LGC cell

Battery

_{Download from Www.Somanuals.c}6_om6_{. All Manuals Search And Download.}

Ch6. Part lists

Location

HFC07

HFC08

Part Number

5901B09271A

0IMCR00011A

Specification

Remarks

FAN Assy

CPU

FAN ASSEMBLY

RH80536GE0252M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M 730

1.60GHZ/600MHZ C0-STEPPING(SL86G)

HFC08

0IMCR00009A

0IMCR00007A

0IMCR00005A

0IMCR00003A

RH80536GE0302M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M 740

1.73GHZ/600MHZ C0-STEPPING(SL7SA)

CPU

RH80536GE0362M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M 750

1.86GHZ/600MHZ C0-STEPPING(SL7S9)

RH80536GE0412M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M 760

2.00GHZ/600MHZ C0-STEPPING(SL7SM)

RH80536GE0462M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M 770

2.13GHZ/600MHZ C0-STEPPING(SL7SL)

HFC09

HFC11

3823B01060A

3823B01061A

3823B01077A

3823B01063A

3823B01064A

3823B01076A

3823B01062A

3823B01065A

3823B01066A

3823B01075A

3823B01068A

3823B01071A

3823B01070A

3823B01067A

3823B01074A

3823B01069A

3823B01072A

3823B01073A

3823B01078A

6708BA0056A

HUNTER-F LG-IBM OKI KOREA . 86KEY

HUNTER-F LG-IBM OKI ENGLISH . 86KEY

TAIWAN HUNTER F OKI 87KEY

RUSSIAN HUNTER F OKI 86KEY

ARABIC HUNTER F OKI 86KEY

THAI HUNTER F OKI 87KEY

KBD

Adapter

US INTER . 87KEY

FARSI HUNTER F OKI 86KEY

SPANISH HUNTER F OKI 87 KEY

ITALIAN HUNTER F OKI 87KEY

FRENCH HUNTER F OKI 87KEY

SWEDEN HUNTER F OKI 87KEY

CZECH HUNTERF OKI 87KEY

HEBREW HUNTER F OKI 87 KEY

HUNGARY HUNTER F OKI 87KEY

PORTUGUESE HUNTER F 87KEY

TURKY HUNTER F OKI 87 KEY

CANADIAN FRENCH HUNTERF OKI 87 KEY

BRAZIL HUNTER F OKI 87KEY

PA-1900-08LK LITEON 90W 19V/4.74A 3PIN WITH PFC HUNTER-ALL FOR KOR

DOMESTIC.

HFC11

6708BA0057A

HP-AP091F13P1 HIPRO 90W 19V/4.74A 3PIN WITH PFC HUNTER-ALL ,FOR KOR

DOMESTIC, SLIM TYPE.

Adapter

_{Download from Www.Somanuals.c}6_om7_{. All Manuals Search And Download.}

Ch6. Part lists

Location

HFC11

Part Number

Specification

Remarks

Adapter

6708BA0056B

PA-1900-08LG LITEON 90W 19V/4.74A 3PIN WITH PFC HUNTER-ALL ,FOR

OVERSEA EXPORT, SLIM TYPE

HFC11

HFC12

6708BA0057B

6911BZ0029C

HP-AP091F13P HIPRO 90W 19V/4.74A 3PIN WITH PFC HUNTER-ALL ,FOR

OVERSEA EXPORT, SLIM TYPE.

Adapter

RTC

N N 200MAH CR2032 WIM TECH NI-MH COIN MCKINLEY L60MM BLUE WIRE

COLOR FOR NT-PC

HFC13

HFS01

6410BM21002

6410BM21601

6410BX21602

6410BX21601

6410BK21005

6410BK21007

6410BK21006

6410BD21003

6410BV21002

6410BV21003

6410BV21602

6410BQ21003

6410BQ21002

6410BO20603

6410BO20602

6410BO21008

6410BU21602

6410BU21603

6410BW21001

6871BH820A1

PT8XXK9KB0A-033 LONGWELL KS 1000MM 3P CONN W/VELCRO TIE BLACK

SP-022+IS-034 H05VV-F I-SHENG KS 1000MM 3P CONN W/VELCRO TIE BLACK

PF8B1CIJ10A-060 LONGWELL GOST 1830MM 3PIN CONN. BLACK

SP-022+IS-034+H05VV-F3G I-SHENG GOST 1800MM 3P CONN. BLACK

PL8B1S3J10A-060 LONGWELL SAA 1830MM 3PIN CONN BLACK

SP-502B+H05VV-F+IS-034 I-SHENG SAA 1830MM 3PIN CONN. BLACK

AU10S3+H03VV-F+VAC5S VOLEX SAA 1830MM 3PIN CONN BLACK

PF8B1CIJ10A-060 LONGWELL CEU 1830MM 3P CONN. BLACK

PF8B1L1J10A-060 LONGWELL SII 1830MM 3PIN CONN. BLACK

SP-86+IS-034 I-SHENG SII 1830MM 3PIN CONN. BLACK

Powercode

SI16S3+H03VV-F+VAC5S VOLEX SII 1830MM 3PIN CONN BLACK

SP-305+H05VV-F+IS-034 I-SHENG INMETRO 1830MM 3PIN CONN BLACK

BR10S3+H03VV-F+VAC5S VOLEX INMETRO 1830MM 3PIN CONN BLACK

P48F1SAJ30A-060 LONGWELL CCC 1830MM 3P CONN BLACK

SP-506+RVV 3CX0.75MM2+IS-034 I-SHENG CCC 1830MM 3P CONN BLACK

GB10S3+RW300_300+VAC5S VOLEX CCC 1830MM 3PIN CONN BLACK

SP-80A+H05VV-F+IS-034 I-SHENG SABS 1830MM 3PIN CONN BLACK

SA16A+H03VV-F+VAC5S VOLEX SABS 1830MM 3PIN CONN BLACK

X-LGPC0415-001 VOLEX ISI 1830MM 3PIN CONN. BLACK

HUNTER-FULL 15 INCH WIMTEC 4 LAYERS 1.0 PP AUDIO SUB B/D ASSY

Sub BD

ASSY

HFS02

HFS03

HFD01

HFD02

3211B00073A

3301B00549A

3111B0TS19A

5022BZ9023A

HUNTER-FULL 15 INCH HINGE FRAME ASSY RIGHT (S-video, hinge right, cushion,

screw)

Sub BD

ASSY

10036875-AB00RRS HUNTER-F/W FCI COMBO EXPRESS CARD SLOT

HUNTER-FULL 15 INCH KBD DECK TOTAL ASSY

PCMCIA

SOCKET

KBD DECK

ASSY

TOUCH PWB 79.7*47.7 HUNTER WIDE WITH SCROLL FUNCTION SYNAPTICS

TM41PUZ307-1

TOUCH PAD

_{Download from Www.Somanuals.c}6_om8_{. All Manuals Search And Download.}

Ch6. Part lists

Location

HFD03

HFD04

HFD05

HFD06

HFM01

Part Number

3551B09756A

6871BH830A1

6850B12005A

4940BM3221A

3111B0TS18A

Specification

Remarks

SPEAKER

BUTTON BD

CABLE

HUNTER-FULL 15 INCH SPEAKER TOTAL ASSY

HUNTER-FULL 15 INCH WIMTEC 2 LAYERS 1.0 PP TOUCH PAD SUB B/D ASSY

UL20696 12P AWM 80C VW-1 L75MM 0.5MM PITCH KFC H154W(TOUCH PAD)

HUNTER-WIDE 15.4 INCH PCABS KBD DECK BUTTON, TOUCHPAD

N N N HUNTER-FULL 15 INCH BOTTOM CASE ASSY 150F

KNOB

BOTTOM

CASE

HFM02

HFM03

3551B09738A

3551B09738B

3551B09733A

HUNTER-FULL 15 INCH COVER RETAINER ASSY 150F FOR DOMESTIC

HUNTER-FULL 15 INCH COVER RETAINER ASSY 150F FOR EXPORT

HUNTER-TL 14.1 INCH COVER ASSY MEMORY/MINI-PCI

RETAINER

ASSY

RETAINER

ASSY

MEMORY

COVER

HFM04

HFM06

3551B09740A

3210BD2020A

HUNTER-FULL 15 INCH COVER ,HDD H150F

HDD COVER

HUNTER-FULL 15 INCH MG HINGE ,FRAME LEFT

HINGE

FRAME

LEFT

HFM07

HFM08

3550BM4047D

3550BM3207A

ME 14 PCABS DUMMY SD MEMORYCARD

SD DUMMY

HUNTER-WIDE 15.4 INCH PCABS CARDBUS DUMMY EXPRESS

EXPRESS

DUMMY

HFM09

HFM10

HFM11

HFM12

3550BM3208A

3550BM3210A

3550BM3204A

3550BM3205A

HUNTER-WIDE 15.4 INCH PCABS CARDBUS DUMMY CARDBUS

HUNTER-WIDE 15.4 INCH RUBBER DUMMY DOCKING

HUNTER-FULL 15 INCH PCABS COVER , HINGE CAP LEFT

HUNTER-FULL 15 INCH PCABS COVER , HINGE CAP RIGHT

CARDBUS

DUMMY

DOCKING

DUMMY

HINGE CAP

LEFT

HINGE CAP

RIGHT

HFM13

HFM14

HTM05

HFM16

3550BM3202A

3301B00553A

6851B76020C

3850BB9110A

HUNTER-WIDE 15.4 INCH PCABS HDD BLOCK

HDD BLOCK

KBD PLATE

MDC CABLE

HUNTER-FULL PLATE KBD ASSY

HUNTER-T N MDC INTERFACE WIM TEK 210MM 2P HUNTER-TL

INTEL GRYPHON BANIAS LOGO 252352-001 INTEL CENTRINO LABEL N N

INTEL

LABEL

HFM16

3850BB9110C

CENTRINO LABEL NT 252352-002 INTEL

INTEL

LABEL

HFM17

HFM19

3850BZ9A15A

3850BB4125A

3850BZ9A87A

MS WIN XP U2 BEZEL 15.4 / 17.1

ATI Label, X600

MS LABEL

ATI LABEL

_{Download from Www.Somanuals.c}6_om9_{. All Manuals Search And Download.}

Ch6. Part lists

Location

HFM19

HFM20

HFM21

HFM22

HFM23

HFM24

HFM25

HFM26

HFM27

Part Number

3850BZ9A87B

3850BF4304A

3850BF4305A

3850BF4306A

3850BF4307A

3850BF4308A

3850BF4304B

3850BF4305B

3850BF4306B

3850BF4307B

3850BF4308B

3850BB4482A

3850BB4483A

3850BB4484A

1SZZBA4017A

1SZZBA4023A

1SZZBZ4014A

1SZZBZ4020A

1SZZBA4097A

1SZZBA4039B

Specification

Remarks

ATI LABEL

POP LABEL

ID LABEL

ATI Label, X600 128M

POP LABEL LS70 PM IPS FOR DOMESTIC

POP LABEL LS70 PM SXGA+ FOR DOMESTIC

POP LABEL LS70 PM GLARE FOR DOMESTIC

POP LABEL LS70 PM XGA FOR DOMESTIC

POP LABEL LS70 GM FOR DOMESTIC

POP LABEL LS70 PM IPS FOR EXPORT

POP LABEL LS70 PM SXGA+ FOR EXPORT

POP LABEL LS70 PM GLARE FOR EXPORT

POP LABEL LS70 PM XGA FOR EXPORT

POP LABEL LS70 GM FOR EXPORT

ID LABEL for Domestic Made in Korea

ID LABEL for Export Made in Korea

ID LABEL for Export Made in China

screw M2.0 * L3.0

ID LABEL

SCREW A

SCREW B

SCREW C

SCREW D

SCREW E

SCREW F

screw M2.0 * L3.5

screw M2.0 * L5.0

screw M2.0 * L10 (Thermal block fix)

screw M2.5 * L6.5

screw M2.5 * L8.0 (hinge)

_{Download from Www.Somanuals.c}7_om0_{. All Manuals Search And Download.}

15.0 EXPLODED VIEW

Location

HFL02

LG P/N

SPECIFICATION

REMARKS

3111B0TS53A HUNTER-FULL 15 INCH COVER REAR ASSY

3858BP4273A Logo Badge (X-Note)

HFL18

3858BZ4462A Logo Badge (LG)

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

HFL04

HFL05

HFL09

HFL10

HFL11

HFL12

LG P/N

SPECIFICATION

REMARKS

4940BM4166A Knob, latch

4970BW4556A Spring, Latch

3300BP4455A Plate, Inverter

3301B00540A Plate, antenna-L (620mm)

3301B00541A Plate, antenna-R (800mm)

6708BI0088A KUBNKM095A ALPS INVERTER

6708BI0089A DAC-08B073 DELTA HUNTER-TL 15 INCH OZ1060S

6708BI0087A KUBNKM094A ALPS INVERTER

6708BI0092A DAC-08B072 DELTA INVERTER

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

LG P/N

SPECIFICATION

REMARKS

HFL01

6304FLP080A

LP150E06-A2 LG PHILPS TFT COLOR 15.0 INCH SXGA+(1400X1050)

ISP STYLE B WVA

HFL01

6304FLP081B LP150E06-A3 LG PHILPS TFT COLOR 15.0 INCH SXGA+(1400X1050)

ISP STYLE B WVA P3 PLANT

6304FHS008A HSD150PK17-A00 HANNSTAR TFT COLOR 15.0 INCH SXGA+(1400X1050)

WVA ISP STYLE B

HFL03

HFL07

HFL08

HFL16

3300BP1079A PLATE, DISPLAY REAR HUNTER 150 FULL

4774BD2005A Hinge Ass’y-L

4774BD2006A Hinge Ass’y,-R

6851B34028A LCD Cable Assy(XGA),Tae-yang

6851B34032A LCD Cable Assy(XGA), Washin

6851B34029A LCD Cable Assy(SXGA),Tae-yang

6851B34033A LCD Cable Assy(SXGA), Washin

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

HFL06

HFL13

HFL14

HFL15

HFL17

LG P/N

SPECIFICATION

REMARKS

3111B0TS24A Case Assy, Front 15.0"

4850BM4029A Cushion, rubber-upper

4826BZ4003B Cushion, rubber-middle

4850BM4030A Cushion, rubber-lower

3850BB3042A Label, front brand name label

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

LG P/N

SPECIFICATION

REMARKS

HFB01

6871BH700A1 HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A)

PP MAIN B/D ASSY(PM128+GB)

HFB01

HFC01

6871BH710A1 HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A)

PP MAIN B/D ASSY(PM64+GB)

6871BH720A1 HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A)

PP MAIN B/D ASSY(PM64+FE)

6871BH730A1 HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A)

PP MAIN B/D ASSY(GM+GB)

6871BH740A1 HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A)

PP MAIN B/D ASSY(GM+FE)

0IMMRIH046A HYS64T32000HDL-5-A INFINEON 200P SODIMM BK

256MB 32MX64 400MHZ DDR2 SDRAM WITH 32MX16

0IMMRHY061A HYMP532S646-E3 HYNIX 200P SODIMM BK 256MB

32MX64 400MHZ DDR2 SDRAM WITH 32MX16

0IMMRSS113A M470T3354BG0-CCC SAMSUNG ELECTRONICS 200P

SODIMM BK 256MB 32MX64 400MHZ DDR2 SDRAM WITH 32MX16

0IMMRIH047A HYS64T64020HDL-5-A INFINEON 200P SODIMM BK 512MB 64MX64 400MHZ

DDR2 SDRAM WITH 32MX16

0IMMRHY062A HYMP564S646-E3 HYNIX 200P SODIMM BK 512MB 64MX64 400MHZ

DDR2 SDRAM WITH 32MX16

0IMMRSS114A M470T6554BG0-CCC SAMSUNG ELECTRONICS 200P SODIMM BK 512MB

64MX64 400MHZ DDR2 SDRAM WITH 32MX16

0IMMR00007A HYS64T32000HDL-3.7-A INFINEON 200P SODIMM BK 256MB 32MX64 533MHZ

DDR2 SDRAM WITH 32MX16

GIMMR00007A HYS64T32000HDL-3.7-A INFINEON 200P SODIMM BK 256MB 32MX64 533MHZ

DDR2 SDRAM WITH 32MX16

0IMMR00005A M470T3354BZ0-LD5 SAMSUNG ELECTRONICS 200P SODIMM BK 256MB

32MX64 533MHZ DDR2 SDRAM WITH 32MX16

0IMMR00008A HYS64T64020HDL-3.7-A INFINEON 200P SODIMM BK 512MB 64MX64 533MHZ

DDR2 SDRAM WITH 32MX16

GIMMR00008A HYS64T64020HDL-3.7-A INFINEON 200P SODIMM BK 512MB 64MX64 533MHZ

DDR2 SDRAM WITH 32MX16

0IMMR00006A M470T6554BZ0-LD5 SAMSUNG ELECTRONICS 200P SODIMM BK 512MB

64MX64 533MHZ DDR2 SDRAM WITH 32MX16

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

LG P/N

SPECIFICATION

REMARKS

HFC08

0IMCR00011A RH80536GE0252M LG INTEL 478P UFCPGA TRAY NT CPU

PENTIUM-M 730 1.60GHZ/600MHZ C0-STEPPING(SL86G)

HFC08

HTC05

0IMCR00009A RH80536GE0302M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M

740 1.73GHZ/600MHZ C0-STEPPING(SL7SA)

0IMCR00007A RH80536GE0362M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M

750 1.86GHZ/600MHZ C0-STEPPING(SL7S9)

0IMCR00005A RH80536GE0412M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M

760 2.00GHZ/600MHZ C0-STEPPING(SL7SM)

0IMCR00003A RH80536GE0462M LG INTEL 478P UFCPGA TRAY NT CPU PENTIUM-M

770 2.13GHZ/600MHZ C0-STEPPING(SL7SL)

6871BG867ZB T60M893T00 FOXCONN 2 LAYERS REV 0.0 MDC1.5 FORM FACTOR

INTERNAL 56K MDC MODEM

HTC05

HFM01

HFM06

HFS01

6871BG869ZB MA560-3 QCOM 2 LAYERS 1A MDC1.5 FORM FACTOR V.92 MODEM CARD

3111B0TS18A N N N HUNTER-FULL 15 INCH BOTTOM CASE ASSY 150F

3210BD2020A HUNTER-FULL 15 INCH MG HINGE ,FRAME LEFT

6871BH820A1 HUNTER-FULL 15 INCH WIMTEC 4 LAYERS 1.0 PP AUDIO SUB B/D ASSY

HFS02

3211B00073A HUNTER-FULL 15 INCH HINGE FRAME ASSY RIGHT

(S-video, hinge right, cushion, screw)

HFM23

HFM24

1SZZBA4023A screw M2.0 * L3.5

1SZZBZ4014A screw M2.0 * L5.0

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

HTA01

HTA02

HTA03

HTA04

LG P/N

SPECIFICATION

REMARKS

4811B00605A HUNTER-WIDE 15.4 INCH HDD SUS 17.1W, 15F

1SZZBA4011A + D3.0 L 3.0 SWRH4 HDD WH [S-PJT] #1 TIP

6744C00085A MHT2040AT PL FUJITSU 40GB EIDE INNER ZEBRA/MACKINLEY/K2

6744C00122A HTS424040M9AT00 HGST 40GB EIDE INNER MCKINLY 4200RPM

6744C00086A MHT2060AT PL FUJITSU 60GB EIDE INNER ZEBRA/MCKINLEY/K2

6744C00106A IC25N060ATMR04-0 HGST 60GB EIDE INNER MCKINLEY/K2 4200RPM

6744C00087A MHT2080AT PL FUJITSU 80GB EIDE INNER ZEBRA/MCKINLEY/K2

6744C00107A IC25N080ATMR04-0 HGST 80GB EIDE INNER MCKINLEY/K2 4200RPM

6744C00123A MHV2100AT FUJITSU 100GB EIDE INNER HUNTER-S 4200RPM

6744C00116A MHT2060BH FUJITSU 60GB SATA INNER HUNTER

6744C00117A MHT2080BH FUJITSU 80GB SATA INNER HUNTER

2020B00030A GCC-4243N HLDS 8X 24X 24X 24X 12.7MM W/COMMON BEZEL FOR BRAND

HTA04

2026B00007A GSA-4080N HLDS 8X 24X 2X 2X 4X 4X 4X 16X 10X 24X NOTE BOOK

12.7MM COMMON TYPE FOR BRAND

2090B20001A DV-28E-C88 TEAC 8X 24X NOTE BOOK 12.7MM W-COMMON BEZEL FOR

BRAND NB-PC

2020B00033A DW-224E-B88 TEAC 8X 24X 24X 24X 12.7MM W-COMMON BEZEL FOR

BRAND NB-PC

2026B00009A DV-W28E-588 TEAC 8X 24X 2X 2X 4X 4X 4X 16X 10X 24X NOTE BOOK

12.7MM W/COMMON BEZEL FOR BRAN NB-PC

HTA05

HTA06

3300BP4459A PLATE, ODD SUPPORT HUNTER 15.4 WIDE .

1SZZBA4041A + D3.5 L3.0MM SWRH4 DUMMY COVER FIX SILVER MAGELLAN DISPLAY

HFC04

6871BZT14AC WM3B2200BGMW2 INTEL 4 LAYERS REV 1.2 PRO/WIRELESS 2200BG

LAN MINI-PCI TYPE CH 1-11 NETWORK CONNECTIO

6871BZT14AD WM3B2200BGRW3 INTEL 4 LAYERS REV 1.2 PRO/WIRELESS 2200BG

LAN MINI-PCI TYPE CH 1-14 NETWORK CONNECTIO

6871BZT14AE? WM3B2915ABGNA INTEL 4 LAYERS REV 2.0 CH 1-11 NETWORK

CONNECTION MINIPCI TYPE IIIB STANDARD

6871BZT14AF? WM3B2915ABGEU INTEL 4 LAYERS REV 2.0 CH 1-13 NETWORK

CONNECTION MINIPCI TYPE IIIB STANDARD

6871BZT14AG? WM3B2915ABGRW INTEL 4 LAYERS REV 2.0 CH 1-13 NETWORK

CONNECTION MINIPCI TYPE IIIB STANDARD

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

HFC07

LG P/N

SPECIFICATION

REMARKS

5901B09271A FAN ASSEMBLY

HFM13

HFM23

HFM24

HFM25

3550BM3202A HUNTER-WIDE 15.4 INCH PCABS HDD BLOCK

1SZZBA4023A screw M2.0 * L3.5

1SZZBZ4014A screw M2.0 * L5.0

1SZZBZ4020A screw M2.0 * L10 (Thermal block fix)

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

HFD01

HFM14

HFM16

HFM17

HFM19

HFM20

HFM23

LG P/N

SPECIFICATION

REMARKS

3111B0TS19A HUNTER-FULL 15 INCH KBD DECK TOTAL ASSY

3301B00553A HUNTER-FULL PLATE KBD ASSY

3850BB9110A INTEL GRYPHON BANIAS LOGO 252352-001 INTEL CENTRINO LABEL N N

3850BB9110C CENTRINO LABEL NT 252352-002 INTEL

3850BZ9A15A MS WIN XP U2 BEZEL 15.4” / 17.1”

3850BB4125A MS WIN XP U2 BEZEL 15.4” / 17.1”

3850BZ9A87A ATI Label, X600

3850BZ9A87B ATI Label, X600 128M

3850BF4304A POP LABEL LS70 PM IPS FOR DOMESTIC

3850BF4305A POP LABEL LS70 PM SXGA+ FOR DOMESTIC

3850BF4306A POP LABEL LS70 PM GLARE FOR DOMESTIC

3850BF4307A POP LABEL LS70 PM XGA FOR DOMESTIC

3850BF4308A POP LABEL LS70 GM FOR DOMESTIC

3850BF4304B POP LABEL LS70 PM IPS FOR EXPORT

3850BF4305B POP LABEL LS70 PM SXGA+ FOR EXPORT

3850BF4306B POP LABEL LS70 PM GLARE FOR EXPORT

3850BF4307B POP LABEL LS70 PM XGA FOR EXPORT

3850BF4308B POP LABEL LS70 GM FOR EXPORT

1SZZBA4023A screw M2.0 * L3.5

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

LG P/N

SPECIFICATION

REMARKS

HFD02

5022BZ9023A TOUCH PWB 79.7*47.7 HUNTER WIDE WITH SCROLL FUNCTION

SYNAPTICS TM41PUZ307-1

HFD03

HFD04

HFD05

HFD06

HFM22

3551B09756A HUNTER-FULL 15 INCH SPEAKER TOTAL ASSY

6871BH830A1 HUNTER-FULL 15 INCH WIMTEC 2 LAYERS 1.0 PP TOUCH PAD SUB B/D ASSY

6850B12005A UL20696 12P AWM 80C VW-1 L75MM 0.5MM PITCH KFC H154W(TOUCH PAD)

4940BM3221A HUNTER-WIDE 15.4 INCH PCABS KBD DECK BUTTON, TOUCHPAD

1SZZBA4017A screw M2.0 * L3.0

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

HFC09

HFM02

HFM07

HFM08

HFM09

HFM10

HFM11

HFM12

HFM26

LG P/N

SPECIFICATION

REMARKS

3823B01060A HUNTER-F LG-IBM OKI KOREA . 86KEY

3823B01061A HUNTER-F LG-IBM OKI ENGLISH . 86KEY

3823B01077A TAIWAN HUNTER F OKI 87KEY

3823B01063A RUSSIAN HUNTER F OKI 86KEY

3823B01064A ARABIC HUNTER F OKI 86KEY

3823B01076A THAI HUNTER F OKI 87KEY

3823B01062A US INTER . 87KEY

3823B01065A FARSI HUNTER F OKI 86KEY

3823B01066A SPANISH HUNTER F OKI 87 KEY

3823B01075A ITALIAN HUNTER F OKI 87KEY

3823B01068A FRENCH HUNTER F OKI 87KEY

3823B01071A SWEDEN HUNTER F OKI 87KEY

3823B01070A CZECH HUNTERF OKI 87KEY

3823B01067A HEBREW HUNTER F OKI 87 KEY

3823B01074A HUNGARY HUNTER F OKI 87KEY

3823B01069A PORTUGUESE HUNTER F 87KEY

3823B01072A TURKY HUNTER F OKI 87 KEY

3823B01073A CANADIAN FRENCH HUNTERF OKI 87 KEY

3823B01078A BRAZIL HUNTER F OKI 87KEY

3551B09738A HUNTER-FULL 15 INCH COVER RETAINER ASSY 150F FOR DOMESTIC

3551B09738B HUNTER-FULL 15 INCH COVER RETAINER ASSY 150F FOR EXPORT

3550BM4047D ME 14 PCABS DUMMY SD MEMORYCARD

3550BM3207A HUNTER-WIDE 15.4 INCH PCABS CARDBUS DUMMY EXPRESS

3550BM3208A HUNTER-WIDE 15.4 INCH PCABS CARDBUS DUMMY CARDBUS

3550BM3210A HUNTER-WIDE 15.4 INCH RUBBER DUMMY DOCKING

3550BM3204A HUNTER-FULL 15 INCH PCABS COVER , HINGE CAP LEFT

3550BM3205A HUNTER-FULL 15 INCH PCABS COVER , HINGE CAP RIGHT

1SZZBA4097A screw M2.5 * L6.5

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

HTA07

LG P/N

SPECIFICATION

REMARKS

6911B00088A 4800MAH 3S-2P SIMPLO LI-ION CYLINDERICAL HUNTER-ALL CELL LGC

6911B00096A 4800MAH 3S-2P SIMPLO LI-ION CYLINDERICAL HUNTER-ALL CELL SDI

6911B00092A 4800MAH 3S-2P LGC LI-ION CYLINDERICAL HUNTER-ALL CELL LGC

6911B00089A 7200MAH 3S-3P SIMPLO LI-ION CYLINDERICAL HUNTER-ALL LGC CELL

6911B00097A 7200MAH 3S-3P SIMPLO LI-ION CYLINDERICAL HUNTER-ALL SDI CELL

HFB01

HFC01

6871BH700A1 HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A)

PP MAIN B/D ASSY(PM128+GB)

6871BH710A1 HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A)

PP MAIN B/D ASSY(PM64+GB)

6871BH720A1 HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A)

PP MAIN B/D ASSY(PM64+FE)

6871BH730A1 HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A)

PP MAIN B/D ASSY(GM+GB)

6871BH740A1 HUNTER-FULL 15 INCH LGE 10 LAYERS (REV 0.7A)

PP MAIN B/D ASSY(GM+FE)

0IMMRIH046A HYS64T32000HDL-5-A INFINEON 200P SODIMM BK

256MB 32MX64 400MHZ DDR2 SDRAM WITH 32MX16

0IMMRHY061A HYMP532S646-E3 HYNIX 200P SODIMM BK 256MB

32MX64 400MHZ DDR2 SDRAM WITH 32MX16

0IMMRSS113A M470T3354BG0-CCC SAMSUNG ELECTRONICS 200P

SODIMM BK 256MB 32MX64 400MHZ DDR2 SDRAM WITH 32MX16

0IMMRIH047A HYS64T64020HDL-5-A INFINEON 200P SODIMM BK 512MB 64MX64 400MHZ

DDR2 SDRAM WITH 32MX16

0IMMRHY062A HYMP564S646-E3 HYNIX 200P SODIMM BK 512MB 64MX64 400MHZ

DDR2 SDRAM WITH 32MX16

0IMMRSS114A M470T6554BG0-CCC SAMSUNG ELECTRONICS 200P SODIMM BK 512MB

64MX64 400MHZ DDR2 SDRAM WITH 32MX16

0IMMR00007A HYS64T32000HDL-3.7-A INFINEON 200P SODIMM BK 256MB 32MX64 533MHZ

DDR2 SDRAM WITH 32MX16

GIMMR00007A HYS64T32000HDL-3.7-A INFINEON 200P SODIMM BK 256MB 32MX64 533MHZ

DDR2 SDRAM WITH 32MX16

0IMMR00005A M470T3354BZ0-LD5 SAMSUNG ELECTRONICS 200P SODIMM BK 256MB

32MX64 533MHZ DDR2 SDRAM WITH 32MX16

0IMMR00008A HYS64T64020HDL-3.7-A INFINEON 200P SODIMM BK 512MB 64MX64 533MHZ

DDR2 SDRAM WITH 32MX16

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

LG P/N

SPECIFICATION

REMARKS

HFC01

GIMMR00008A HYS64T64020HDL-3.7-A INFINEON 200P SODIMM BK 512MB 64MX64 533MHZ

DDR2 SDRAM WITH 32MX16

HFC01

0IMMR00006A M470T6554BZ0-LD5 SAMSUNG ELECTRONICS 200P SODIMM BK 512MB

64MX64 533MHZ DDR2 SDRAM WITH 32MX16

HTC13

HFM03

HFM04

HTM08

HTM09

HTM10

HTM17

6410BM21002 PT8XXK9KB0A-033 LONGWELL KS 1000MM 3P CONN W/VELCRO TIE BLAC

6410BM21601 SP-022+IS-034 H05VV-F I-SHENG KS 1000MM 3P CONN W/VELCRO TIE BLACK

6410BX21602 PF8B1CIJ10A-060 LONGWELL GOST 1830MM 3PIN CONN. BLACK

6410BX21601 SP-022+IS-034+H05VV-F3G I-SHENG GOST 1800MM 3P CONN. BLACK

6410BK21005 PL8B1S3J10A-060 LONGWELL SAA 1830MM 3PIN CONN BLACK

6410BK21007 SP-502B+H05VV-F+IS-034 I-SHENG SAA 1830MM 3PIN CONN. BLACK

6410BK21006 AU10S3+H03VV-F+VAC5S VOLEX SAA 1830MM 3PIN CONN BLACK

6410BD21003 PF8B1CIJ10A-060 LONGWELL CEU 1830MM 3P CONN. BLACK

6410BV21002 PF8B1L1J10A-060 LONGWELL SII 1830MM 3PIN CONN. BLACK

6410BV21003 SP-86+IS-034 I-SHENG SII 1830MM 3PIN CONN. BLACK

6410BV21602 SI16S3+H03VV-F+VAC5S VOLEX SII 1830MM 3PIN CONN BLACK

6410BQ21003 SP-305+H05VV-F+IS-034 I-SHENG INMETRO 1830MM 3PIN CONN BLACK

6410BQ21002 BR10S3+H03VV-F+VAC5S VOLEX INMETRO 1830MM 3PIN CONN BLACK

6410BO20603 P48F1SAJ30A-060 LONGWELL CCC 1830MM 3P CONN BLACK

6410BO20602 SP-506+RVV 3CX0.75MM2+IS-034 I-SHENG CCC 1830MM 3P CONN BLACK

6410BO21008 GB10S3+RW300_300+VAC5S VOLEX CCC 1830MM 3PIN CONN BLACK

6410BU21602 SP-80A+H05VV-F+IS-034 I-SHENG SABS 1830MM 3PIN CONN BLACK

6410BU21603 SA16A+H03VV-F+VAC5S VOLEX SABS 1830MM 3PIN CONN BLACK

6410BW21001 X-LGPC0415-001 VOLEX ISI 1830MM 3PIN CONN. BLACK

3551B09733A HUNTER-TL 14.1 INCH COVER ASSY MEMORY/MINI-PCI

3551B09740A “HUNTER-FULL 15 INCH COVER ,HDD H150F

3551B09732A HUNTER-TL 14.1" / 15" INCH HDD COVER ASSY W/ FOOT RUBBER

3551B09733A HUNTER-TL 14.1" /15" INCH COVER ASSY MEMORY/MINI-PCI¡–

3610BM4024A GIRAFFE CR RUBBER FOOT 14.1" / 15"

3850BB4475A ID LABEL HUNTER T 14 DOMESTIC

3850BB4476A ID LABEL HUNTER T 15 DOMESTIC

3850BB4479A ID LABEL HUNTER T 14 EXPORT

3850BB4480A ID LABEL HUNTER T 15 EXPORT

3850BB4485A ID LABEL HUNTER 14T EXPORT LGEKS MADE IN CHINA

3850BB4489A ID LABEL HUNTER 14T CHINA FROM LGEPT

3850BB4489B ID LABEL HUNTER 14T CHINA FROM LGEKS

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

HTM17

HFM21

LG P/N

SPECIFICATION

REMARKS

3850BB4486A ID LABEL HUNTER 15T LGEKS MADE IN CHINA

3850BB4490A ID LABEL HUNTER 15T CHINA FROM LGEPT

3850BB4490B ID LABEL HUNTER 15T CHINA FROM LGEKS

3850BB4482A ID LABEL for Domestic Made in Korea

3850BB4483A ID LABEL for Export Made in Korea

3850BB4484A ID LABEL for Export Made in China

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Download from Www.Somanuals.com. All Manuals Search And Download.

15.0 EXPLODED VIEW

Location

LG P/N

6708

SPECIFICATION

REMARKS

HFC11

BA0056A PA-1900-08LK LITEON 90W 19V/4.74A 3PIN WITH PFC HUNTER-ALL

FOR KOR DOMESTIC.

HFC11

6708BA0057A HP-AP091F13P1 HIPRO 90W 19V/4.74A 3PIN WITH PFC HUNTER-ALL,

FOR KOR DOMESTIC, SLIM TYPE.

6708BA0056B PA-1900-08LG LITEON 90W 19V/4.74A 3PIN WITH PFC HUNTER-ALL,

FOR OVERSEA EXPORT, SLIM TYPE”

6708BA0057B HP-AP091F13P HIPRO 90W 19V/4.74A 3PIN WITH PFC HUNTER-ALL,

FOR OVERSEA EXPORT, SLIM TYPE.

HFC13

HFM22

HFM26

HFM27

6410BM21002 PT8XXK9KB0A-033 LONGWELL KS 1000MM 3P CONN W/VELCRO TIE BLACK