Safety and Reference
Please read this manual carefully before operating your set and retain it for
future reference.
OLED65G6P
OLED77G6P
*MFL69383631*
P/NO : MFL69383631 (1601-REV00)
Download from Www.Somanuals.com. All Manuals Search And Download.
• Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
• CAUTION concerning the Power Cord
(Can differ by country):
Check the specification page of this owner’s
manual to be certain concerning current
requirements. Do not connect too many
devices to the same AC power outlet as this
could result in fire or electric shock. Do not
overload wall outlets. Overloaded wall outlets,
loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked
wire insulation are dangerous. Any of these
conditions could result in electric shock or fire.
Periodically examine the cord of your device,
and if its appearance indicates damage or
deterioration, unplug it, discontinue use of
the device, and have the cord replaced with
an exact replacement part by an authorized
servicer. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the device. Do not
move the TV with the power cord plugged in. Do
not use a damaged or loose power cord. Be sure
do grasp the plug when unplugging the power
cord. Do not pull on the power cord to unplug
the TV.
• Unplug this apparatus during lightning storms
or when unused for long periods of time.
• Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
• Do not press strongly upon the panel with a
hand or a sharp object such as a nail, pencil, or
pen, or make a scratch on it.
• Warning - To reduce the risk of fire or electrical
shock, do not expose this product to rain,
moisture or other liquids. Do not touch the TV
with wet hands. Do not install this product near
flammable objects such as gasoline or candles,
or expose the TV to direct air conditioning.
• Do not stick metal objects or any other
conductive material into the power cord. Do
not touch the end of the power cord while it is
plugged in.
• Keep the packing anti-moisture material or
vinyl packing out of the reach of children.
Anti-moisture material is harmful if swallowed.
If swallowed, induce vomiting and go to the
nearest hospital. Additionally, vinyl packing can
cause suffocation. Keep it out of the reach of
children.
• Do not expose to dripping or splashing and
do not place objects filled with liquids, such as
vases, cups, etc. on or over the apparatus (e.g.,
on shelves above the unit).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
• Grounding
• Cleaning
- (Except for devices which are not grounded.)
Ensure that you connect the earth ground wire
to prevent possible electric shock (i.e., a TV
with a three-prong grounded AC plug must
be connected to a three-prong grounded AC
outlet).
- When cleaning, unplug the power cord and
wipe gently with a soft cloth to prevent
scratching. Do not spray water or other liquids
directly on the TV as electric shock may occur.
Do not clean with chemicals such as alcohol,
thinners, or benzene.
If grounding methods are not possible, have
a qualified electrician install a separate circuit
breaker. Do not try to ground the unit by
connecting it to telephone wires, lightning
rods, or gas pipes.
• Moving
- Make sure the product is turned off, unplugged,
and all cables have been removed. It may take 2
or more people to carry larger TVs. Do not press
or put stress on the front panel of the TV.
• Ventilation
- Install your TV where there is proper ventilation.
Do not install in a confined space such as a
bookcase. Do not cover the product with cloth
or other materials while plugged in. Do not
install in excessively dusty places.
• If you smell smoke or other odors coming from
the TV, unplug the power cord and contact an
authorized service center.
• Keep the product away from direct sunlight.
• Never touch this apparatus or antenna during a
lightning storm.
• When mounting a TV on the wall, make sure not
to install the TV by hanging the power and signal
cables on the back of the TV.
• Do not allow an impact shock or any objects to
fall into the product, and do not drop anything
onto the screen.
• DISCONNECTING THE DEVICE FROM THE MAIN
POWER
The power plug is the disconnecting device.
In case of an emergency, the power plug must
remain readily accessible.
• Make sure the power cord is connected securely
to the power plug on the TV.
Power
Supply
Circuit
Breaker
• As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if the unit is turned off.
• Do not attempt to modify this product in any
way without written authorization from LG
Electronics. Unauthorized modification could
void the user’s authority to operate this product.
• Outdoor Antenna Grounding
- (Can differ by country):
If an outdoor antenna is installed, follow
the precautions below. An outdoor antenna
system should not be located in the vicinity of
overhead power lines or other electric light or
power circuits, or where it can come in contact
with such power lines or circuits as death or
serious injury can occur. Be sure the antenna
system is grounded to provide some protection
against voltage surges and built-up static
charges. Section 810 of the National Electrical
Code (NEC) in the U.S.A. provides information
with respect to proper grounding of the mast
and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size
of grounding conductors, location of antenna
discharge unit, connection to grounding
electrodes, and requirements for the grounding
electrode.
• Batteries
- Store the accessories (battery, etc.) in a safe
location out of the reach of children.
• This apparatus uses batteries. In your community
there might be regulations that require you
to dispose of these batteries properly due to
environmental considerations. Please contact
your local authorities for disposal or recycling
information.
Antenna grounding according to the National
Electrical Code, ANSI/NFPA 70
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Ground Clamp
Electric Service
Equipment
Grounding Conductor
(NEC Section 810-21)
Ground Clamp
Power Service Grounding
Electrode System
(NEC Art 250, Part H)
NEC: National Electrical Code
4
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not dispose of batteries in a fire.
• Do not short circuit, disassemble, or allow the
batteries to overheat.
• Do not use high voltage electrical equipment
near the TV, (e.g., a bug zapper).
Viewing 3D Imaging
(For 3D models)
This may result in product malfunction.
• Dot Defect
CAUTION
• Guardians should not leave children
unsupervised who are watching a 3D video.
Guardians should make children stop watching
the video and take a rest if they experience eye
fatigue, headache, or dizziness.
• When viewing a 3D video, some may experience
discomfort such as a headache, dizziness,
fatigue, or blurred vision. In this case, stop
watching the 3D video and take a rest.
• If you watch a 3D video for a long time, you
may experience eye fatigue. In this case, stop
watching the 3D video and take a rest.
• Only use LG 3D glasses. Otherwise, you may not
be able to view 3D videos properly.
- This panel is an advanced product that contains
millions of pixels. In a very few cases, you could
see fine dots on the screen while you’re viewing
the TV. Those dots are deactivated pixels and
do not affect the performance and reliability
of the TV.
• Generated Sound
- Cracking noise A cracking noise that occurs
when watching or turning off the TV is
generated by plastic thermal contraction
due to temperature and humidity. This noise
is common for products where thermal
deformation is required.
- Electrical circuit humming/panel buzzing
A low level noise is generated from a high-
speed switching circuit, which supplies a
large amount of current to operate a product.
It varies depending upon the product.
This generated sound does not affect the
performance and reliability of the product.
• Take care not to touch the ventilation openings.
When watching the TV for a long period, the
ventilation openings may become hot. This does
not affect the performance of the product or
cause defects in the product.
• Do not use 3D glasses instead of your normal
glasses, sunglasses, or protective goggles. Place
the 3D glasses over your normal eye ware.
• Do not keep your 3D glasses in extremely high or
low temperatures. It will cause deformation.
• Do not use the 3D glasses while walking or
moving around. It may cause an accident or
injury.
• Be careful not to poke your eye with the frames
of the 3D glasses.
• Do not watch 3D content if you have
photosensitive seizures, epilepsy, or heart
disease.
• Do not install this product on a wall if it could be
exposed to oil or oil mist. This may damage the
product and cause it to fall.
• If the TV feels cold to the touch, there may
be a small flicker when it is turned on. This is
normal; there is nothing wrong with TV. Some
minute dot defects may be visible on the screen,
appearing as tiny red, green, or blue spots.
However, they have no adverse effect on the
TV’s performance. Avoid touching the screen or
holding your finger(s) against it for long periods
of time. Doing so may produce some temporary
distortion effects on the screen.
• Displaying a still image for a prolonged time may
cause image sticking. Avoid displaying a fixed
image on the TV screen for a long period of time.
• Some horizontal lines may appear when the
Clear Panel Noise feature is performed. It is
normal and there is no need to be concerned.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing
CAUTION
• Do not use any unapproved items to ensure the
safety and product’s lifespan.
• Any damages or injuries by using unapproved
items are not covered by the warranty.
• Some models appear to have a thin film on the
screen. It is actually part of the screen; do not
remove it.
• When attaching the stand to the TV set, place
the screen facing down on a cushioned table or
flat surface to protect the screen from scratches.
• Make sure that the screws are fastened tightly.
(If they are not fastened securely enough, the TV
may tilt forward after being installed.)
• Do not fasten the screws with excessive force;
otherwise, they may be worn out and become
loose.
NOTE
• When the TV is turned on for the first time after
being shipped from the factory, initialization of
the TV may take approximately one minute.
• Image shown may differ from your TV.
• Your TV’s OSD (On Screen Display) may differ
slightly from that shown in this manual.
• The available menus and options may differ from
the input source or product model that you are
using.
• New features may be added to this TV in the
future.
• The items supplied with your product may vary
depending upon the model.
• Product specifications or contents of this manual
may be changed without prior notice due to
upgrade of product functions.
• For an optimal connection, HDMI cables and
USB devices should have bezels less than 10 mm
(0.39 inches) thick and 18 mm (0.7 inches) width.
• Use an extension cable that supports USB 2.0 if
the USB cable or USB flash drive does not fit into
your TV’s USB port.
• Make sure to wring any excess water or cleaner
from the cloth.
• Do not spray water or cleaner directly onto the
TV screen.
• Make sure to spray just enough of water or
cleaner onto a dry cloth to wipe the screen.
Optional Extras
• Use a certified cable with the HDMI logo
attached. If you do not use a certified HDMI
cable, the screen may not display or a
connection error may occur.
Optional extras can be changed or modified for
quality improvement without any notification.
Contact your dealer for buying these items.
These devices work only with certain models.
The model name or design may be changed due to
the manufacturer’s circumstances or policies.
• Recommended HDMI cable types (3 m or less)
- High-Speed HDMI®/TM cable
- High-Speed HDMI ®/TM cable with Ethernet
(Depending upon model)
B
B
AG-F***
AG-F***DP
Cinema 3D Glasses
Dual Play Glasses
A
A
AN-MR650
AN-VC550
*A 10 mm (0.39 inches)
*B 18 mm (0.7 inches)
Magic Remote
Smart Camera
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Lifting and Moving the TV
CAUTION
• Avoid touching the screen at all times, as this
may result in damage to the screen.
When moving or lifting the TV, read the following
to prevent the TV from being scratched or
damaged and for safe transportation regardless of
its type and size.
• It is recommended to move the TV in the box or
packing material that the TV originally came in.
• Before moving or lifting the TV, disconnect the
power cord and all cables.
• Do not place the product on the floor with its
front facing down without padding. Failure to do
so may result in damage to the screen.
• Do not move the TV by holding the cable
holders, as the cable holders may break, and
injuries and damage to the TV may occur.
(Depending upon model)
• Make sure to attach the AV box fixing supporter
to the AV box before you lift the product and
move. Moving the product without attaching the
AV box fixing supporter to the AV box first may
cause injury to your fingers.
• When holding the TV, the screen
should face away from you to
avoid damage.
• Hold the top and bottom of the TV frame firmly.
Make sure not to hold the transparent part,
speaker, or speaker grille area.
• Use at least two people to move
a large TV.
• When transporting the TV by
hand, hold the TV as shown in the
following illustration.
• When transporting the TV, do not expose the TV
to jolts or excessive vibration.
• When transporting the TV, keep the TV upright;
never turn the TV on its side or tilt towards the
left or right.
• When handling the TV, be careful not to damage
the protruding buttons.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Button
Mounting on a Table
You can simply operate the TV functions, pressing
or moving the button.
1 Lift and tilt the TV into its upright position on a
table.
- Leave a 10 cm (4 inches) (minimum) space from
the wall for proper ventilation.
10 cm
(4 inches)
Joystick Button
2 Connect the power cord to a wall outlet.
CAUTION
• Do not place the TV near or on sources of heat,
as this may result in fire or other damage.
Basic Functions
Power On (Press)
Power Off (Press and Hold)1
Securing the TV to a Wall (optional)
Volume Control
(Depending upon model)
Channels Control
1 All running apps will close.
Adjusting the Menu
When the TV is turned on, press button one time.
You can adjust the Menu items pressing or moving
the buttons.
1 Insert and tighten the eye-bolts, or TV brackets
and bolts on the back of the TV.
- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall. Match the location of the wall bracket and
the eye-bolts on the rear of the TV.
Turns the power off.
Accesses the setting menu.
Clears on-screen displays and returns to TV
viewing.
Changes the input source.
3 Connect the eye-bolts and wall brackets tightly
with a sturdy rope or cable. Make sure to keep
the rope parallel to the flat surface.
CAUTION
• Make sure that children do not climb on or hang
on the TV.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
NOTE
• Use a platform or cabinet that is strong and large
enough to support the TV securely.
• Brackets, bolts, and ropes are optional. You can
obtain additional accessories from your local
dealer.
• Fold the AV box before installing the TV on a wall
mount by performing the stand attachment in
reverse.
• To install the wall mount, switch the selector
to WALL TYPE as shown in the following
illustration. (For OLED77G6P)
Mounting on a Wall
An optional wall mount can be used with your
LG Television. Consult with your local dealer for
a wall mount that supports the VESA standard
used by your TV model. Carefully attach the wall
mount bracket at the rear of the TV. Install the wall
mount bracket on a solid wall perpendicular to the
floor. If you are attaching the TV to other building
materials, please contact qualified personnel to
install the wall mount. Detailed instructions will
be included with the wall mount. We recommend
that you use an LG brand wall mount. The LG wall
mount is easy to adjust or to connect the cables.
When you do not use LG’s wall mount bracket,
use a wall mount bracket where the device is
adequately secured to the wall with enough space
to allow connectivity to external devices. If you are
using a non-adjustable mount, attach the mount
to the wall. Attach the cables to the TV first, then
attach the TV to the mount.
CAUTION
• Fold the AV box and attach the AV box fixing
supporter to the AV box before installing the
product on a wall mount.
(For OLED65G6P)
Provided Item
2
1
AV Box Fixing
Supporter
X 2
(For OLED77G6P)
10 cm
(4 inches)
Provided Item
10 cm
10 cm
10 cm
X 2
Make sure to use screws and wall mounts that
meet the VESA standard. Standard dimensions for
the wall mount kits are described in the following
table.
AV Box Fixing
Supporter
Model
VESA (A x B)
Standard screw M6
OLED65G6P
400 x 200
OLED77G6P
600 x 300
M8 (4EA) /
M4 (2EA)
X 2
Number of
4
6
screws
Wall mount
bracket
OTW420B
OTW630B
(optional)
A
9
B
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to an Antenna or Cable
Connections (Notifications)
Connect an antenna, cable, or cable box to watch
TV. The illustrations may differ from the actual
items and an RF cable is optional.
You can connect various external devices to the TV.
Supported external devices are: HD receivers, DVD
players, VCRs, audio systems, USB storage devices,
PC, gaming devices, and other external devices.
For more information on an external device’s
connection, refer to the manual provided with
each device.
CAUTION
• Make sure not to bend the copper wire of the RF
cable.
NOTE
• If you record a TV program on a DVD recorder or
VCR, make sure to connect the TV signal input
cable to the TV through a DVD recorder or VCR.
For more information about recording, refer to
the manual provided with the connected device.
• The external device connections shown may
differ slightly from illustrations in a manual.
• Connect external devices to the TV regardless
about the order of the TV port.
• If you connect a gaming device to the TV, use the
cable supplied with the gaming device.
• Refer to the external equipment’s manual for
operating instructions.
• In PC mode, there may be noise associated
with the resolution, vertical pattern, contrast,
or brightness. If noise is present, change the PC
output to another resolution, change the refresh
rate to another rate, or adjust the brightness and
contrast on the PICTURE menu until the picture
is clear.
• Depending upon the graphics card, some
resolution settings may not allow the image to
be positioned on the screen properly.
Copper wire
• Complete all connections between devices, and
then connect the power cord to the power outlet
to prevent damage to your TV.
NOTE
• Use a signal splitter to use 2 TVs or more.
• DTV Audio Supported Codec: MPEG,
Dolby Digital.
• Direct ULTRA HD broadcast is unavailable in
areas without an ULTRA HD signal.
• This TV cannot receive ULTRA HD (3840 x 2160
pixels) broadcasts directly because the related
standards have not been confirmed.
(Depending upon model)
Other Connections
Connect your TV to external devices. For the best
picture and audio quality, connect the external
device and the TV with the HDMI cable. Depending
upon the model, a cable may not be provided.
• Some USB Hubs may not work. If a USB device
connected through a USB Hub is not detected,
connect it directly to the USB port on the TV.
• The TV may be capable of operating without a
set-top from a multichannel video programming
distributor (MVPD).
NOTE
>
•
>
> General >
HDMI ULTRA HD Deep Color:
- On : Support 4K @ 60 Hz (4:4:4, 4:2:2, 4:2:0)
- Off : Support 4K @ 60 Hz 8bit (4:2:0)
• If the device connected to Input Port also
supports ULTRA HD Deep Color, your picture
may be clearer. However, if the device doesn’t
support it, it may not work properly. In that case,
connect the device to a different HDMI port or
change the TV’s HDMI ULTRA HD Deep Color
setting to Off.
- This feature is available only on certain models
which support HDMI ULTRA HD Deep Color.
• HDMI Audio Supported Format:
DTS (44.1 kHz / 48 kHz),
AC3 (32 kHz / 44.1 kHz / 48 kHz),
PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz /
192 kHz) (Depending upon model)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Slim Remote Control
B
(Depending upon model)
Returns to the previous screen.
The descriptions in this manual are based on
the buttons on the remote control. Please read
this manual carefully and use the TV correctly.
To replace coin batteries, turn the battery cover
counterclockwise by using a coin. Then, take the
battery cover. Insert and fix the battery (CR2032)
with the facing forward. And, Put the battery
cover on the remote control and turn it clockwise
to close.
* Clears all on-screen displays and returns to
TV viewing.
(Home) Accesses the Home menu.
(InPUT) Changes the input source.
* Pressing and holding the (InPUT) button
displays all the lists of external inputs.
(navigation buttons) Scrolls through
menus or options. (up/down/left/right)
When in use, it should be pointed in the direction
of the TV’s remote sensor.
Selects menus or options and confirms your
input.
* : To use the button, press and hold for more than
3 seconds.
Battery Installation
A
WARNING
DO NOT INGEST BATTERY. CHEMICAL BURN
HAZARD.
CAUTION
B
• The battery used in this device may present a
fire or chemical burn hazard if mistreated. Do
not recharge, disassemble, incinerate, or heat
above 100 °C (212 °F). Replace the battery part
no. CR2032 only. Use of another battery may
present a risk of fire or explosion. Dispose of
used battery. Keep battery away from children.
Do not disassemble or dispose of in fire.
• [The remote control supplied with] This product
contains a coin/button cell battery. If the coin/
button cell battery is swallowed, it can cause
severe internal burns in just 2 hours and can lead
to death. Keep new and used batteries away
from children. If the battery compartment does
not close securely, stop using the product and
keep it away from children. If you think batteries
might have been swallowed or placed inside
any part of the body, seek immediate medical
attention.
A
(POWER) Turns the TV on or off.
You can turn your set-top box on or off
by adding the set-top box to the universal remote
control for your TV.
• If you have long nails, do not open the battery
cover by using your finger. Or else, your nail
could break.
Adjusts the volume level.
(MUTE) Mutes all sounds.
* Video descriptions function will be enabled.
• SAP (Secondary Audio Program) Feature can also
be enabled by pressing the
key.
Scrolls through the saved channels.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Magic Remote Functions
A
(Depending upon model)
(POWER) Turns the TV on or off.
When the message Magic remote battery is low.
Change the battery. is displayed, replace the
battery. To install batteries, open the battery cover,
replace batteries (1.5 V AA) matching and
ends to the label inside the compartment, and
close the battery cover. Failure to match the correct
polarities of the battery may cause the battery to
burst or leak, resulting in fire, personal injury, or
ambient pollution. Be sure to point the remote
control at the remote control sensor on the TV.
To remove the batteries, perform the installation
actions in reverse.
You can turn your set-top box on or off
by adding the set-top box to the universal remote
control for your TV.
Number button Enters numbers.
- (Dash) Inserts a dash between numbers such as
2-1 and 2-2.
Accesses the saved channel list.
(Screen Remote) Displays the Screen Remote.
• Accesses the Universal Control Menu in some
regions.
This remote uses infrared light. When in use, it
should be pointed in the direction of the TV’s
remote sensor.
B
Adjusts the volume level.
(MUTE) Mutes all sounds.
* Video descriptions function will be enabled.
• SAP (Secondary Audio Program) Feature can also
be enabled by pressing the
key.
Scrolls through the saved channels.
(Home) Accesses the Home menu.
* Shows the previous history.
A
B
(Search) Search for content such as channels,
movies and other videos, or perform a web search
by entering your search terms in the search box.
(Voice recognition) * Network connection is
required to use the voice recognition function.
1 Press the (Voice recognition) button.
2 Speak when the voice display window appears
on the TV screen.
Displays the set-top box Home menu.
(When you are not watching with a set-top box:
the set-top box screen is displayed.)
C
12
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Deregister the Magic Remote
C
Press the
/
and
(Home) buttons
at the same time, for five seconds, to unpair the
Magic Remote with your TV.
(Navigation buttons) Press the up, down,
left or right button to scroll the menu.
(up/down/left/right)
• Pressing and holding the
button will
let you cancel and re-register Magic Remote at
once.
If you press
buttons while the pointer is in
use, the pointer will disappear from the screen and
Magic Remote will operate like a general remote
control. To display the pointer on the screen again,
shake Magic Remote to the left and right.
Licenses
(Wheel) (OK) Press the center of the Wheel
button to select a menu. You can change channels
by using the Wheel button.
Supported licenses may differ by model.
For more information about licenses,
Returns to the previous screen.
* Clears all on-screen displays and returns to
TV viewing.
Used for viewing 3D video. (For 3D models)
(INPUT) Changes the input source.
* Pressing and holding the (INPUT) button
displays all the lists of external inputs.
Activates or deactivates the subtitles.
Displays the program event according to
time scheduler.
Open Source Software Notice
Information
(Q. Settings) Accesses the quick settings.
* Pressing and holding the (Q. Settings) button
displays the All Settings menu.
To obtain the source code under GPL, LGPL, MPL,
and other open source licenses, that is contained in
In addition to the source code, all referred license
terms, warranty disclaimers and copyright notices
are available for download. LG Electronics will also
provide open source code to you on CD-ROM for
a charge covering the cost of performing such
distribution (such as the cost of media, shipping,
and handling) upon email request to opensource@
lge.com. This offer is valid for three (3) years from
the date on which you purchased the product.
Color buttons These access special functions in
some menus.
(
Red,
Green,
Yellow,
Blue)
,
,
,
Control buttons for media contents
You can zoom in on the area where the
remote control is pointed.
* By zooming in on the selected area,
you can view it in full screen.
* : To use the button, press and hold for more than
3 seconds.
External Control Device Setup
Registering Magic Remote
To obtain the external control device setup
(Depending upon model)
How to Register the Magic Remote
To use the Magic Remote, first pair it with your TV.
1 Put batteries into the Magic Remote and turn the
TV on.
2 Point the Magic Remote at your TV and press the
(Wheel) (OK) on the remote control.
• If the TV fails to register the Magic Remote, try
again after turning the TV off and back on.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Environment Condition
Troubleshooting
• Operating Temperature
0 °C to 40 °C (32 °F to 104 °F)
• Operating Humidity
Less than 80 %
• Cannot control the TV with the remote control.
- Check if anything such as tape has been placed
over the receiver.
- Check if there is any obstacle between the
product and the remote control.
- Replace the batteries with new ones.
• No image display and no sound is produced.
- Check if the product is turned on.
- Check if the power cord is connected to a wall
outlet.
• Storage Temperature
- 20 °C to 60 °C (-4 °F to 140 °F)
• Storage Humidity
Less than 85 %
Wireless Module (LGSBWAC61)
Specifications
- Check if there is a problem in the wall outlet by
connecting other products.
• The TV turns off suddenly.
- Check the power control settings. The power
supply may be interrupted.
- Check if the Sleep Timer / Timer Power Off
feature is activated in the Timers settings.
- If there is no signal while the TV is on, the TV
will turn off automatically after 15 minutes of
inactivity.
Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency Range
2400 to 2483.5 MHz
5150 to 5725 MHz
5725 to 5850 MHz
Output Power (Max.)
15 dBm
16 dBm
12.5 dBm
Bluetooth
Frequency Range
Output Power (Max.)
2400 to 2483.5 MHz
10 dBm
• As band channels can vary per country, the
user cannot change or adjust the operating
frequency. This product is configured for the
regional frequency table.
• For consideration of the user, this device should
be installed and operated with a minimum
distance of 20 cm (7.8 inches) between the
device and the body.
Specifications
Product specifications may be changed without
prior notice due to upgrade of product functions.
Estimated yearly energy consumption indicated on
the FTC label is measured in accordance with the
Test Procedures for Television Sets (USA only).
The actual energy consumption depends on the
usage environment (The content watched, TV
settings, etc.).
• FCC ID: BEJLGSBWAC61
IC: 2703H-LGSBWAC61
Television System
ATSC, NTSC-M, 64 & 256 QAM
Program Coverage
VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135,
CADTV 1-135
External Antenna Impedance
75 Ω
14
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC RF Radiation Exposure Statement
Regulatory
[For having wireless function (WLAN, Bluetooth,...)]
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-
located or operating in conjunction with any other
antenna or transmitter.
FCC Notice
(For USA)
This equipment should be installed and operated
with minimum distance 20 cm (7.8 inches)
between the antenna and your body. Users must
follow the specific operating instructions for
satisfying RF exposure compliance.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more of
the following measures:
Industry Canada Statement
(For Canada)
[For having wireless function (WLAN, Bluetooth,...)]
This device complies with Industry Canada’s
licence-exempt RSSs. Operation is subject to the
following two conditions:
1 This device may not cause interference; and
2 This device must accept any interference,
including interference that may cause undesired
operation of the device.
- Reorient or relocate the receiving antenna.
- Increase the separation between the
equipment and the receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
IC Radiation Exposure Statement
(For Canada)
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference and (2) this device must accept any
interference received, including interference that
may cause undesired operation of the device.
Any changes or modifications in construction of
this device which are not expressly approved by
the party responsible for compliance could void
the user’s authority to operate the equipment.
[For having wireless function (WLAN, Bluetooth,...)]
This equipment complies with IC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed
and operated with minimum distance 20 cm (7.8
inches) between the antenna & your body.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE
FOR ANY RADIO OR TV INTERFERENCE CAUSED
BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD
VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
FCC Radio Frequency Interference
Requirements (for UNII devices)
High power radars are allocated as primary users
of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands.
These radar stations can cause interference with
and/or damage this device. This device cannot be
co-located with any other transmitter.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING!
WARNING
(For Canada)
[For product having the wireless function using 5
GHz frequency bands]
1 The device for operation in the band 5150–5250
MHz is only for indoor use to reduce the
potential for harmful interference to co-channel
mobile satellite systems;
Never place a television set in an unstable
location. A television set may fall, causing serious
personal injury or death. Many injuries, particularly
to children, can be avoided by taking simple
precautions such as:
• Using cabinets or stands recommended by the
manufacturer of the television set.
• Only using furniture that can safely support the
television set.
2 For devices with detachable antenna(s), the
maximum antenna gain permitted for devices in
the bands 5250-5350 MHz and 5470-5725 MHz
shall be such that the equipment still complies
with the e.i.r.p. limit;
• Ensuring the television set is not overhanging
the edge of the supporting furniture.
• Not placing the television set on tall furniture
(for example, cupboards or bookcases) without
anchoring both the furniture and the television
set to a suitable support.
• Not placing the television set on cloth or other
materials that may be located between the
television set and supporting furniture.
• Educating children about the dangers of
climbing on furniture to reach the television set
or its controls.
3 For devices with detachable antenna(s), the
maximum antenna gain permitted for devices in
the band 5725-5850 MHz shall be such that the
equipment still complies with the e.i.r.p. limits
specified for point-to-point and non-point-to-
point operation as appropriate; and
4 The worst-case tilt angle(s) necessary to remain
compliant with the e.i.r.p. elevation mask
requirement set forth in Section 6.2.2(3) shall be
clearly indicated.(devices operating in the band
5250-5350 MHz with a maximum e.i.r.p. greater
than 200 mW)
If your existing television set is being retained
and relocated, the same considerations as above
should be applied.
5 High-power radars are allocated as primary
users (i.e. priority users) of the bands 5250–5350
MHz and 5650–5850 MHz and that these radars
could cause interference and/or damage to LE-
LAN devices.
Symbols
Refers to alternating current(AC).
Refers to direct current(DC).
Refers to class II equipment.
Refers to stand-by.
Note to Cable/TV Installer
(For USA and Canada)
Refers to “ON” (power).
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the
Refers to dangerous voltage.
National Electric Code (U.S.A.). The code provides
guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected
to the grounding system of the building, as close
to the point of the cable entry as practical.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
CHILD SAFETY:
PROPER TELEVISION PLACEMENT MATTERS
THE CONSUMER ELECTRONICS INDUSTRY CARES
• Manufacturers, retailers and the rest of the consumer electronics industry are committed to
making home entertainment safe and enjoyable.
• As you enjoy your television, please note that all televisions – new and old- must be supported on
proper stands or installed according to the manufacturer’s recommendations. Televisions that
are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests, carts, etc.,
may fall over, resulting in injury.
TUNE IN TO SAFETY
• ALWAYS follow the manufacturer’s recommendations for the safe installation of your television.
• ALWAYS read and follow all instructions for proper use of your television.
• NEVER allow children to climb on or play on the television or the furniture on which the television
is placed.
• NEVER place the television on furniture that can easily be used as steps, such as a chest of
drawers.
• ALWAYS install the television where it cannot be pushed, pulled over or knocked down.
• ALWAYS route cords and cables connected to the television so that they cannot be tripped
over, pulled or grabbed.
WALL OR CEILING MOUNT YOUR TELEVISION
• ALWAYS contact your retailer about professional installation if you have any doubts about your
ability to safely mount your television.
• ALWAYS use a mount that has been recommended by the television manufacturer and has a
safety certification by an independent laboratory (such as UL, CSA, ETL).
• ALWAYS follow all instructions supplied by the television and mount manufacturers.
• ALWAYS make sure that the wall or ceiling where you are mounting the television is appropriate.
Some mounts are not designed to be mounted to walls and ceilings with steel studs or cinder
block construction. If you are unsure, contact a professional installer.
• Televisions can be heavy. A minimum of two people is required for a wall or ceiling mount
installation.
MOVING AN OLDER TELEVISION TO A NEW PLACE IN
YOUR HOME
• Many new television buyers move their older CRT televisions into a secondary room after the
purchase of a flat-panel television. Special care should be made in the placement of older CRT
televisions.
• ALWAYS place your older CRT television on furniture that is sturdy and appropriate for its size
and weight.
• NEVER place your older CRT television on a dresser where children may be tempted to use the
drawers to climb.
• ALWAYS make sure your older CRT television does not hang over the edge of your furniture.
CE.org/safety
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
Trade Name LG
Model OLED65G6P-U, OLED77G6P-U
Responsible LG Electronics Inc.
Party
Address
1000 Sylvan Ave.
Englewood Cliffs NJ 07632
U.S.A
TEL
201 - 266 - 2534
LG Customer Information Center
The model and serial numbers of the TV are located on the
back and one side of the TV.
Record them below should you ever need service.
1-800-243-0000
1-888-865-3026
1-888-542-2623
USA, Consumer User
USA, Commercial User
CANADA
Register your product online!
MODEL
SERIAL
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S MANUAL
EXTERNAL CONTROL
DEVICE SETUP
Please read this manual carefully before operating the set and retain it for
future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY CODES
2
KEY CODES
• This feature is not available for all models.
Code
(Hexa)
Code
(Hexa)
Function
CH +, PR +
Note
Function
Note
00
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
53
5B
60
61
63
71
72
79
91
7A
7C
7E
8E
8F
AA
AB
B0
B1
List
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
01
CH -, PR -
Volume +
Exit
02
PIP(AD)
Blue
03
Volume -
06
> (Arrow Key / Right Key)
< (Arrow Key / Left Key)
Power
Yellow
Green
Red
07
08
09
Mute
Ratio / Aspect Ratio
AD (Audio Description)
User Guide
0B
0E
0F
Input
SLEEP
TV, TV/RAD
Smart / Home
SIMPLINK
10 - 19 * Number Key 0 - 9
1A
1E
20
21
28
30
Q.View / Flashback
FAV (Favorite Channel)
Text (Teletext)
►► (Forward)
◄◄ (Rewind)
Info
T. Opt (Teletext Option)
Return (BACK)
Program Guide
► (Play)
AV (Audio / Video) Mode
ꕗ (Stop / File List)
ꕘ (Freeze / Slow Play /
39
40
41
Caption/Subtitle
R/C Button
R/C Button
R/C Button
BA
BB
BD
R/C Button
R/C Button
R/C Button
Pause)
Λ
(Arrow Key / Cursor Up)
Soccer
V (Arrow Key / Cursor
Down)
ꔄ (REC)
42
43
44
45
4C
My Apps
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
DC
99
3D
R/C Button
R/C Button
R/C Button
Menu / Settings
OK / Enter
AutoConfig
App / *
9F
Q.Menu
List, - (ATSC Only)
* Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel.
(For South Korea, Japan, North America, Latin America except Colombia models)
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL CONTROL DEVICE SETUP
3
EXTERNAL CONTROL DEVICE SETUP
• Image shown may differ from your TV.
Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer
or an A/V control system) to control the product’s functions externally.
Note: The type of control port on the TV can be different between model series.
* Please be advised that not all models support this type of connectivity.
* Cable is not provided.
USB to Serial converter with USB Cable
USB Type
(TV)
(PC)
• LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial converter
which is not made nor provided by LG.
• It can be purchased from computer stores that carry accessories for IT support professionals.
RS-232C With RS232C Cable
DE9 (D-Sub 9pin) Type
• You need to purchase the RS-232C (DE9, D-Sub 9pin female-to-female type) to RS-232C cable required
for the connection between the PC and the TV, which is specified in the manual.
RS-232C IN
(CONTROL & SERVICE)
(PC)
(TV)
The connection interface may differ from your TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL CONTROL DEVICE SETUP
4
Phone jack Type
• You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and
the TV, which is specified in the manual.
* For other models, connect to the USB port.
* The connection interface may differ from your TV.
1
3
(PC)
(TV)
(TV)
2
- or
1
3
(PC)
RS-232C IN
(CONTROL & SERVICE)
2
Customer Computer
RS-232C configurations
3-Wire Configurations(Not standard)
1
5
PC
TV
RXD
TXD
GND
2
3
5
2
1
3
TXD
RXD
GND
OR
6
9
RXD
TXD
GND
3
2
5
2
1
3
TXD
RXD
GND
RS-232C
(Serial port)
D-Sub 9
Phone
Set ID
For Set ID number, see "Real Data Mapping" on p.6
1. Press SETTINGS to access the main menus.
2. Press the Navigation buttons to scroll to (*General → About this TV or OPTION) and press OK.
3. Press the Navigation buttons to scroll to SET ID and press OK.
4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.
5. When you are finished, press EXIT.
* (Depending on model)
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL CONTROL DEVICE SETUP
5
Communication Parameters
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
• Stop bit : 1 bit
• Communication code : ASCII code
• Use a crossed (reverse) cable.
Command reference list
(Depending on model)
DATA
(Hexadecimal)
DATA
(Hexadecimal)
COMMAND1 COMMAND2
COMMAND1 COMMAND2
01. Power*
k
k
a
c
00 to 01
15. Balance
k
x
t
00 to 64
16. Color
(Colour)
Temperature
02. Aspect
Ratio
(p.7)
(p.7)
u
00 to 64
(p.8)
17. ISM
Method (Only j
Plasma TV)
03. Screen
Mute
k
d
p
04. Volume
Mute
k
k
k
e
f
00 to 01
00 to 64
00 to 64
18. Equalizer j
v
(p.8)
05. Volume
Control
19. Energy
Saving
j
q
00 to 05
20. Tune
Command
06. Contrast
g
m
a
b
(p.9)
21. Channel
(Programme)
Add/Del(Skip)
m
00 to 01
07.
Brightness
k
k
h
i
00 to 64
00 to 64
08. Color/
Colour
22. Key
m
m
c
Key Codes
00 to 64
23. Control
Backlight,
Control Panel
Light
g
09. Tint
k
j
00 to 64
10.
Sharpness
24. Input
select (Main)
x
x
b
t
(p.11)
(p.11)
(p.11)
k
k
k
l
00 to 32
00 to 01
11. OSD
Select
25. 3D (Only
3D models)
12. Remote
Control Lock
Mode
26. Extended x
3D (Only 3D
models)
v
k
k
k
m
r
00 to 01
00 to 64
00 to 64
27. Auto
Configure
j
u
(p.12)
13. Treble
14. Bass
s
* Note: During playing or recording media, all commands except Power (ka) and Key (mc) are not
executed and treated as NG.
With RS232C cable, TV can communicate "ka command" in power-on or power-off status. but with
USB-to-Serial converter cable, the command works only if TV is on.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL CONTROL DEVICE SETUP
6
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the TV. (j, k, m or x)
[Command 2] : Second command to control the TV.
[Set ID]
: You can adjust the [Set ID] to choose desired monitor ID number in option menu.
Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set
can be controlled.
* [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on
transmission/receiving protocol.
[DATA]
[Cr]
: To transmit command data (hexadecimal). Transmit ‘FF’ data to read status of command.
: Carriage Return - ASCII code ‘0x0D’
[ ]
: Space – ASCII code ‘0x20’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.
Data 00: Illegal Code
Real data mapping (Hexadecimal b Decimal)
* When you enter the [data] in hexadecimal, refer to following conversion table.
* Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.
00 : Step 0
01 : Step 1 (Set ID 1)
32 : Step 50 (Set ID 50)
33 : Step 51 (Set ID 51)
FE : Step 254
FF : Step 255
...
...
...
0A : Step 10 (Set ID 10)
63 : Step 99 (Set ID 99)
01 00 : Step 256
...
...
...
0F : Step 15 (Set ID 15)
10 : Step 16 (Set ID 16)
...
C7 : Step 199
C8 : Step 200
...
27 0E : Step 9998
27 0F : Step 9999
...
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL CONTROL DEVICE SETUP
7
* Commands may work differently depending on model and signal.
01. Power (Command: k a)
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
► To control Power *On or Off of the set.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
* In case of video mute on only, TV will display On
Screen Display(OSD). But, in case of Screen mute
on, TV will not display OSD.
Data 00 : Power Off
01 : *Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
04. Volume Mute (Command: k e)
► To Show TV is Power On or *Off
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK][Data][x]
► To control volume mute on/off.
You can also adjust mute using the MUTE button
on remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
* Similarly, if other functions transmit ‘FF’ data
based on this format, Acknowledgement feedback
presents status about each function.
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
02. Aspect Ratio (Command: k c)
(Main Picture Size)
05. Volume Control (Command: k f)
► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the
Aspect Ratio in the Q.MENU. or PICTURE menu.
► To adjust volume.
You can also adjust volume with the volume
buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen 07 : 14:9
Data Min : 00 to Max : 64
(4:3)
02 : Wide screen
(16:9)
(Europe, Colombia, Mid-East,
Asia except South Korea and
Japan)
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
04 : Zoom
09 : * Just Scan
0B : Full Wide
(Europe, Colombia, Mid-
East, Asia except South
Korea and Japan)
06. Contrast (Command: k g)
05 : Zoom 2
(Latin America
except Colombia
Only)
► To adjust screen contrast.
You can also adjust contrast in the PICTURE
menu.
06 : Set by Program/ 10 to 1F : Cinema Zoom 1 to 16
Original 0c : 21:9 (Depending on model)
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3
screen aspect ratio.
* In DTV/HDMI/Component mode (high-definition),
Just Scan is available.
07. Brightness (Command: k h)
► To adjust screen brightness.
You can also adjust brightness in the PICTURE
menu.
* Full wide mode may work differently based on
model and is supported for DTV fully, and ATV,
AV partially.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
03. Screen Mute (Command: k d)
► To select screen mute on/off.
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][d][ ][Set ID][ ][Data][Cr]
08. Color/Colour (Command: k i)
Data 00 : Screen mute off (Picture on)
Video mute off
► To adjust the screen Color(Colour).
01 : Screen mute on (Picture off)
10 : Video mute on
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL CONTROL DEVICE SETUP
8
Data Min : 00 to Max : 64
* (Depending on model)
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
14. Bass (Command: k s)
09. Tint (Command: k j)
► To adjust Bass.
► To adjust the screen tint.
You can also adjust in the AUDIO menu.
You can also adjust tint in the PICTURE menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
Ack [s][ ][Set ID][ ][OK/NG][Data][x]
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
* (Depending on model)
15. Balance (Command: k t)
10. Sharpness (Command: k k)
► To adjust balance.
► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE
menu.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
Data Min : 00 to Max : 32
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
16. Color(Colour) Temperature (Command: x u)
► To adjust colour temperature. You can also adjust
11. OSD Select (Command: k l)
Color(Colour) Temperature in the PICTURE menu.
► To select OSD (On Screen Display) on/off when
Transmission [x][u][ ][Set ID][ ][Data][Cr]
controlling remotely.
Data Min : 00 to Max : 64
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
Data 00 : OSD off
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
17. ISM Method (Command: j p) (Only Plasma TV)
► To control the ISM method. You can also adjust
12. Remote control lock mode (Command: k m)
ISM Method in OPTION menu.
► To lock the front panel controls on the monitor and
Transmission [j][p][ ][Set ID][ ][Data][Cr]
remote control.
Data Min : 02: Orbiter
08: Normal
Transmission [k][m][ ][Set ID][ ][Data][Cr]
20: Color(Colour) Wash
Data 00 : Lock off
01 : Lock on
Ack [p][ ][Set ID][ ][OK/NG][Data][x]
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this
mode.
18. Equalizer (Command : j v)
When main power is off & on (plug-off and plug-in,
after 20 - 30 seconds), external control lock is
released.
► Adjust EQ of the set.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
MSB
0
LSB
0
* In the standby mode (DC off by off timer or ‘ka’,
‘mc’ command), and if key lock is on, TV will not
turn on by power on key of IR & Local Key.
0
0
0
0
0
0
Frequency
Data
13. Treble (Command: k r)
► To adjust treble.
Frequency
1st Band
2nd Band
3rd Band
4th Band
7
0
0
0
0
6
0
0
1
1
5
0
1
0
1
4
3
2
0
0
...
1
0
0
1
...
Step
You can also adjust in the AUDIO menu.
0
0
...
0
0
...
0
0
...
0(decimal)
1(decimal)
...
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [r][ ][Set ID][ ][OK/NG][Data][x]
19(decimal)
0
0
0
1
1
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL CONTROL DEVICE SETUP
9
Set ID = All = 00
5th Band
20(decimal)
1
0
0
0
0
1
0
1
Data 00 & 01 = Channel Data is 10 = 00 0a
Data 02 = Analog Antenna TV = 00
Result = ma 00 00 0a 00
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
* It depends on model, and can adjust when sound
mode is EQ adjustable value.
2. Tune to the digital antenna (DVB-T) Channel 01.
Set ID = All = 00
Data 00 & 01 = Channel Data is 1 = 00 01
Data 02 = Digital Antenna TV = 10
Result = ma 00 00 01 10
19. Energy Saving (Command: j q)
► To reduce the power consumption of the TV. You
can also adjust Energy Saving in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
3. Tune to the satellite (DVB-S) Channel 1000.
Set ID = All = 00
Data
00 : Off
01 : Minimum
02 : Medium
Data 00 & 01 = Channel Data is 1000 = 03 E8
Data 02 = Digital Satellite TV = 40
Result = ma 00 03 E8 40
03 : Maximum
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][x][a][ ][Set ID][ ][NG][Data 00][x]
04 : Auto (For LCD TV / LED TV) /
Intelligent sensor (For PDP TV)
05 : Screen off
• For South Korea, North/Latin America except
Colombia Model
* (Depending on model)
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
► To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
20. Tune Command (Command: m a)
Digital channels have a Physical, Major, and Minor
channel number. The Physical number is the actual
digital channel number, the Major is the number that
the channel should be mapped to, and the Minor is
* This command may work differently depending on
model and signal.
• For Europe, Mid-East, Colombia, Asia except
South Korea and Japan Model
the sub-channel. Since the ATSC tuner automatically
maps the channel from the Major / Minor number,
the Physical number is not required when sending a
command in Digital.
► Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ]
[Data 01][ ][Data 02][Cr]
* Analog Antenna/Cable
* Analog Antenna/Cable
Data 00 : Physical Channel Number
[Data 00][Data 01] Channel Data
Data 00 : High byte channel data
Data 01 : Low byte channel data
- 00 00 ~ 00 C7 (Decimal : 0 ~ 199)
- Antenna (ATV) : 02~45 (Decimal: 2 ~ 69)
- Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
[Data 01 ~ 04]: Major/Minor Channel Number
Data 01 & 02: xx (Don't care)
Data 03 & 04: xx (Don't care)
Data 05: Input Source (Analog)
- 00 : Antenna TV (ATV)
Data 02 : Input Source (Analog)
- 00 : Antenna TV (ATV)
- 80 : Cable TV (CATV)
* Digital Antenna/Cable/Satellite
- 01 : Cable TV (CATV)
* Digital Antenna/Cable
[Data 00][Data 01]: Channel Data
Data 00 : High Channel data
Data 01 : Low Channel data
Data 00 : xx (Don't care)
- 00 00 ~ 27 0F (Decimal: 0 ~ 9999)
[Data 01][Data 02]: Major Channel Number
Data 01 : High byte Channel Data
Data 02 : Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor Channel Number
Data 03 : High byte Channel Data
Data 04 : Low byte Channel Data
Data 02 : Input Source (Digital)
- 10 : Antenna TV (DTV)
- 20 : Antenna Radio (Radio)
- 40 : Satellite TV (SDTV)
- 50 : Satellite Radio (S-Radio)
- 90 : Cable TV (CADTV)
- a0 : Cable Radio (CA-Radio)
Data 05 : Input Source (Digital)
- 02 : Antenna TV (DTV) – Use Physical Channel
Number
- 06 : Cable TV (CADTV) – Use Physical Channel
* Tune Command Examples:
1. Tune to the Analog antenna (PAL) Channel 10.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL CONTROL DEVICE SETUP
10
Number
Data 05 = Digital Antenna TV = 02
- 22 : Antenna TV (DTV) – Don’t Use Physical
Channel Number
Total = ma 00 00 00 11 00 01 02
- 26 : Cable TV (CADTV) - Don’t Use Physical
Channel Number
- 46 : Cable TV (CADTV) – Use Major Channel
Number Only (One Part Channel)
2. Tune to the BS (ISDB-BS) channel 30.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Don’t Care = 00 00
Data 05 = Digital BS TV = 07
Two bytes are available for each major and minor
channel data, but usually the low byte is used alone
(high byte is 0).
Total = ma 00 00 00 1E 00 00 07
* Tune Command Examples:
1. Tune to the Analog cable (NTSC) channel 35.
Set ID = All = 00
Data 00 = Channel Data is 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = Analog Cable TV = 01
Total = ma 00 23 00 00 00 00 01
* This feature is varied based on the model.
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
21. Channel(Programme) Add/Del(Skip)
(Command: m b)
2. Tune to the digital antenna (ATSC) channel 30-3.
Set ID = All = 00
► To skip current channel(programme) for next time.
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = Digital Antenna TV = 22
Total = ma 00 00 00 1E 00 03 22
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Del(ATSC,ISDB)/Skip(DVB) 01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
* Set the saved channel status to del(ATSC, ISDB)/
skip(DVB) or add.
• For Japan Model
► To tune channel to following physical/major/minor
22. Key (Command: m c)
number.
► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Data Key code - p.2.
* Digital Antenna/Satellite
Data 00: xx (Don't care)
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
[Data 01][Data 02]: Major Channel Number
Data 01: High byte Channel Data
Data 02: Low byte Channel Data
23. Control Backlight (Command: m g)
• For LCD TV / LED TV
► To control the backlight.
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
[Data 03][Data 04]: Minor/Branch Channel Number
(Don’t care in Satellite)
Data 03: High byte Channel Data
Data 04: Low byte Channel Data
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
Control Panel Light (Command: m g)
Data 05 : Input Source (Digital/Satellite for Japan)
- 02 : Antenna TV (DTV)
• For Plasma TV
► To control the panel light.
- 07 : BS (Broadcasting Satellite)
- 08 : CS1 (Communication Satellite 1)
- 09 : CS2 (Communication Satellite 2)
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Tune Command Examples:
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
1
Tune to the digital antenna (ISDB-T) channel 17-1
Set ID = All = 00
.
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 17 = 00 11
Data 03 & 04 = Minor/Branch is 1 = 00 01
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL CONTROL DEVICE SETUP
11
24. Input select (Command: x b)
(Main Picture Input)
00
01
02
03
O
X
X
X
O
X
X
O
O
X
X
O
► To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data
X : don’t care
00 : DTV
01 : CADTV
10 : ATV
02 : Satellite DTV
ISDB-BS (Japan)
03 : ISDB-CS1 (Japan)
04 : ISDB-CS2 (Japan)
11 : CATV
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02]
[Data03][x]
[t][ ][Set ID][ ][NG][Data00][x]
20 : AV or AV1
21 : AV2
26. Extended 3D(Command: x v) (only 3D models)
(Depending on model)
40 : Component1
60 : RGB
41 : Component2
► To change 3D option for TV.
Transmission [x][v][ ][Set ID][ ][Data 00][ ]
[Data 01][Cr]
90 : HDMI1
92 : HDMI3
91 : HDMI2
93 : HDMI4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
[Data 00] 3D option
* This function depends on model and signal.
00 : 3D Picture Correction
01 : 3D Depth (3D Mode is Manual Only)
02 : 3D Viewpoint
06 : 3D Color Correction
07 : 3D Sound Zooming
08 : Normal Image View
09 : 3D Mode (Genre)
25. 3D(Command: x t) (only 3D models)
(Depending on model)
► To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01]
[Data 01] It has own range for each 3D option
determined by [Data 00].
1) When [Data 00] is 00
00 : Right to Left
[ ][Data 02][ ][Data 03][Cr]
* (Depending on model)
Data Structure
[Data 00] 00 : 3D On
01 : 3D Off
01 : Left to Right
02 : 3D to 2D
03 : 2D to 3D
2) When [Data 00] is 01, 02
Data
Min: 0 - Max: 14 (*transmit by Hexadecimal
code)
[Data 01] 00 : Top and Bottom
01 : Side by Side
Data value range(0 - 20) converts Viewpoint range
(-10 - +10) automatically (Depending on model)
* This option works when 3D Mode (Genre) is manual
only.
02 : Check Board
03 : Frame Sequential
04 : Column interleaving
05 : Row interleaving
[Data 02] 00 : Right to Left
01 : Left to Right
3) When [Data 00] is 06, 07
00 : Off
01 : On
[Data 03] 3D Effect(3D Depth): Min : 00 - Max : 14
(*transmit by Hexadecimal code)
* [Data 02], [Data 03] functions depend on model
and signal.
4) When [Data 00] is 08
00 : Revert to 3D video from 3D-to-2D
converted 2D video
01 : Change 3D video to 2D video, except
2D-to-3D video
* If [Data 00] is 00 (3D On), [Data 03] has no
meaning.
* If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data
01], [Data 02] and [Data 03] have no meaning.
* If conversion condition doesn’t meet, command is
treated as NG.
* If [Data 00] is 03 (2D to 3D), [Data 01] and
[Data 02] have no meaning.
5) When [Data 00] is 09
* If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data
03] works when 3D Mode (Genre) is manual only.
00 : Standard
02 : Cinema
04 : Manual
01 : Sport
03 : Extreme
05 : Auto
* All 3D pattern options ([Data 01]) may not be
available according to broadcasting/video signal.
Ack [v][ ][Set ID][ ][OK][Data00][Data01][x]
[v][ ][Set ID][ ][NG][Data00][x]
[Data 00]
[Data 01]
[Data 02]
[Data 03]
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL CONTROL DEVICE SETUP
12
27. Auto Configure (Command: j u)
(Depending on model)
► To adjust picture position and minimize image
shaking automatically. It works only in RGB (PC)
mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01 : To set
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
Easy Setup Guide
OLED TV
OLED65G6P
OLED77G6P
Please read this manual carefully before operating your set and retain it for future reference.
ESPAÑOL
Guía Rápida de Configuración
Lea atentamente este manual antes de poner en marcha el equipo y consérvelo para futuras consultas.
FRANÇAIS
Guide de configuration rapide
Avant d’utiliser l’appareil, veuillez lire attentivement ce guide et conservez-le pour pouvoir vous y reporter ultérieurement.
AA
CR2032
OLED65G6P
OLED77G6P
X2
(M8 X L77)
X18
(M4 X L12)
X 4
(M10 x L70)
X 2
(M4 x L10)
X 2
X 2
P/No: MFL69383610 (1601-REV00)
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH Read Safety and Reference.
ESPAÑOL Leer Seguridad y Consultas.
FRANÇAIS Lisez Sécurité et références.
Download from Www.Somanuals.com. All Manuals Search And Download.
OLED65G6P
3
4
2
1
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OLED77G6P
2
3
4
5
1
10
6
7
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
4
2
4
1
3
1
3
1
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2
0
1
ENGLISH
OLED65G6P
(OLED65G6P-U)
1,461 x 883 x 243 (mm)
57.5 x 34.7 x 9.5 (inches)
1,461 x 892 x 68 (mm)
57.5 x 35.1 x 2.6 (inches)
31.7 kg (69.8 lbs)
OLED77G6P
(OLED77G6P-U)
1,734 x 1,055 x 317 (mm)
68.2 x 41.5 x 12.4 (inches)
1,734 x 1,067 x 83 (mm)
68.2 x 42.0 x 3.2 (inches)
52.0 kg (114.6 lbs)
-
MODELS
Stand type
Dimensions
(W x H x D)
Wall mount type
Weight
For USA and Canada
For Mexico
3.2 A / 320 W
Current value / Power consumption
Power requirement
4.4 A / 440 W
-
AC 120 V ~ 50 / 60 Hz
ESPAÑOL
FRANÇAIS
MODELOS
MODÈLES
OLED65G6P
(OLED65G6P-U)
1 461 x 883 x 243 (mm)
OLED77G6P
(OLED77G6P-U)
1 734 x 1 055 x 317 (mm)
Párese tipo
Dimensiones
(Ancho x altura x profundidad)
Sur support
57,5 x 34,7 x 9,5 (pulgadas / po) 68,2 x 41,5 x 12,4 (pulgadas / po)
Tipo de montaje en pared
Sur fixation murale
1 461 x 892 x 68 (mm)
1 734 x 1 067 x 83 (mm)
Dimensions
(L x H x P)
57,5 x 35,1 x 2,6 (pulgadas / po)
68,2 x 42,0 x 3,2 (pulgadas / po)
Peso
31,7 kg (69,8 libras / lb)
52,0 kg (114,6 libras / lb)
Poids
Para Estados Unidos y Canadá
Para México
3,2 A / 320 W
4,4 A / 440 W
3,2 A / 320 W
4,4 A / 440 W
-
-
-
-
Corriente de consumo / Consumo de potencia
Valeur courante / Consommation électrique
Pour les États-Unis et le Canada
Pour le Mexique
Alimentación requerida
Alimentation
AC 120 V ~ 50 / 60 Hz
Download from Www.Somanuals.com. All Manuals Search And Download.
|