LG Electronics Flat Panel Television OLED55B6P User Manual
Safety and Reference  
Please read this manual carefully before operating your set and retain it for  
future reference.  
OLED55B6P OLED55C6P OLED55E6P  
OLED65B6P OLED65C6P OLED65E6P  
www.lg.com  
*MFL69383602*  
P/NO : MFL69383602 (1601-REV00)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Use only with the cart, stand, tripod, bracket, or  
table specified by the manufacturer, or sold with  
the apparatus. When a cart is used, use caution  
when moving the cart/apparatus combination to  
avoid injury from tip-over.  
• CAUTION concerning the Power Cord  
(Can differ by country):  
Check the specification page of this owner’s  
manual to be certain concerning current  
requirements. Do not connect too many  
devices to the same AC power outlet as this  
could result in fire or electric shock. Do not  
overload wall outlets. Overloaded wall outlets,  
loose or damaged wall outlets, extension cords,  
frayed power cords, or damaged or cracked  
wire insulation are dangerous. Any of these  
conditions could result in electric shock or fire.  
Periodically examine the cord of your device,  
and if its appearance indicates damage or  
deterioration, unplug it, discontinue use of  
the device, and have the cord replaced with  
an exact replacement part by an authorized  
servicer. Protect the power cord from physical or  
mechanical abuse, such as being twisted, kinked,  
pinched, closed in a door, or walked upon. Pay  
particular attention to plugs, wall outlets, and  
the point where the cord exits the device. Do not  
move the TV with the power cord plugged in. Do  
not use a damaged or loose power cord. Be sure  
do grasp the plug when unplugging the power  
cord. Do not pull on the power cord to unplug  
the TV.  
• Unplug this apparatus during lightning storms  
or when unused for long periods of time.  
• Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has  
been damaged in any way, such as power-supply  
cord or plug is damaged, liquid has been spilled  
or objects have fallen into the apparatus, the  
apparatus has been exposed to rain or moisture,  
does not operate normally, or has been dropped.  
• Do not press strongly upon the panel with a  
hand or a sharp object such as a nail, pencil, or  
pen, or make a scratch on it.  
• Warning - To reduce the risk of fire or electrical  
shock, do not expose this product to rain,  
moisture or other liquids. Do not touch the TV  
with wet hands. Do not install this product near  
flammable objects such as gasoline or candles,  
or expose the TV to direct air conditioning.  
• Do not stick metal objects or any other  
conductive material into the power cord. Do  
not touch the end of the power cord while it is  
plugged in.  
• Keep the packing anti-moisture material or  
vinyl packing out of the reach of children.  
Anti-moisture material is harmful if swallowed.  
If swallowed, induce vomiting and go to the  
nearest hospital. Additionally, vinyl packing can  
cause suffocation. Keep it out of the reach of  
children.  
• Do not expose to dripping or splashing and  
do not place objects filled with liquids, such as  
vases, cups, etc. on or over the apparatus (e.g.,  
on shelves above the unit).  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Grounding  
• Cleaning  
- (Except for devices which are not grounded.)  
Ensure that you connect the earth ground wire  
to prevent possible electric shock (i.e., a TV  
with a three-prong grounded AC plug must  
be connected to a three-prong grounded AC  
outlet).  
- When cleaning, unplug the power cord and  
wipe gently with a soft cloth to prevent  
scratching. Do not spray water or other liquids  
directly on the TV as electric shock may occur.  
Do not clean with chemicals such as alcohol,  
thinners, or benzene.  
If grounding methods are not possible, have  
a qualified electrician install a separate circuit  
breaker. Do not try to ground the unit by  
connecting it to telephone wires, lightning  
rods, or gas pipes.  
• Moving  
- Make sure the product is turned off, unplugged,  
and all cables have been removed. It may take 2  
or more people to carry larger TVs. Do not press  
or put stress on the front panel of the TV.  
• Ventilation  
- Install your TV where there is proper ventilation.  
Do not install in a confined space such as a  
bookcase. Do not cover the product with cloth  
or other materials while plugged in. Do not  
install in excessively dusty places.  
• If you smell smoke or other odors coming from  
the TV, unplug the power cord and contact an  
authorized service center.  
• Keep the product away from direct sunlight.  
• Never touch this apparatus or antenna during a  
lightning storm.  
• When mounting a TV on the wall, make sure not  
to install the TV by hanging the power and signal  
cables on the back of the TV.  
• Do not allow an impact shock or any objects to  
fall into the product, and do not drop anything  
onto the screen.  
• DISCONNECTING THE DEVICE FROM THE MAIN  
POWER  
The power plug is the disconnecting device.  
In case of an emergency, the power plug must  
remain readily accessible.  
• Make sure the power cord is connected securely  
to the power plug on the TV.  
Power  
Supply  
Circuit  
Breaker  
• As long as this unit is connected to the AC wall  
outlet, it is not disconnected from the AC power  
source even if the unit is turned off.  
• Do not attempt to modify this product in any  
way without written authorization from LG  
Electronics. Unauthorized modification could  
void the user’s authority to operate this product.  
• Outdoor Antenna Grounding  
- (Can differ by country):  
If an outdoor antenna is installed, follow  
the precautions below. An outdoor antenna  
system should not be located in the vicinity of  
overhead power lines or other electric light or  
power circuits, or where it can come in contact  
with such power lines or circuits as death or  
serious injury can occur. Be sure the antenna  
system is grounded to provide some protection  
against voltage surges and built-up static  
charges. Section 810 of the National Electrical  
Code (NEC) in the U.S.A. provides information  
with respect to proper grounding of the mast  
and supporting structure, grounding of the  
lead-in wire to an antenna discharge unit, size  
of grounding conductors, location of antenna  
discharge unit, connection to grounding  
electrodes, and requirements for the grounding  
electrode.  
• Batteries  
- Store the accessories (battery, etc.) in a safe  
location out of the reach of children.  
• This apparatus uses batteries. In your community  
there might be regulations that require you  
to dispose of these batteries properly due to  
environmental considerations. Please contact  
your local authorities for disposal or recycling  
information.  
Antenna grounding according to the National  
Electrical Code, ANSI/NFPA 70  
Antenna Lead in Wire  
Antenna Discharge Unit  
(NEC Section 810-20)  
Ground Clamp  
Electric Service  
Equipment  
Grounding Conductor  
(NEC Section 810-21)  
Ground Clamp  
Power Service Grounding  
Electrode System  
(NEC Art 250, Part H)  
NEC: National Electrical Code  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Do not dispose of batteries in a fire.  
• Do not short circuit, disassemble, or allow the  
batteries to overheat.  
• Do not use high voltage electrical equipment  
near the TV, (e.g., a bug zapper).  
Viewing 3D Imaging  
(For 3D models)  
This may result in product malfunction.  
• Dot Defect  
CAUTION  
• Guardians should not leave children  
unsupervised who are watching a 3D video.  
Guardians should make children stop watching  
the video and take a rest if they experience eye  
fatigue, headache, or dizziness.  
• When viewing a 3D video, some may experience  
discomfort such as a headache, dizziness,  
fatigue, or blurred vision. In this case, stop  
watching the 3D video and take a rest.  
• If you watch a 3D video for a long time, you  
may experience eye fatigue. In this case, stop  
watching the 3D video and take a rest.  
• Only use LG 3D glasses. Otherwise, you may not  
be able to view 3D videos properly.  
- This panel is an advanced product that contains  
millions of pixels. In a very few cases, you could  
see fine dots on the screen while you’re viewing  
the TV. Those dots are deactivated pixels and  
do not affect the performance and reliability  
of the TV.  
• Generated Sound  
- Cracking noise A cracking noise that occurs  
when watching or turning off the TV is  
generated by plastic thermal contraction  
due to temperature and humidity. This noise  
is common for products where thermal  
deformation is required.  
- Electrical circuit humming/panel buzzing  
A low level noise is generated from a high-  
speed switching circuit, which supplies a  
large amount of current to operate a product.  
It varies depending upon the product.  
This generated sound does not affect the  
performance and reliability of the product.  
• Take care not to touch the ventilation openings.  
When watching the TV for a long period, the  
ventilation openings may become hot. This does  
not affect the performance of the product or  
cause defects in the product.  
• Do not use 3D glasses instead of your normal  
glasses, sunglasses, or protective goggles. Place  
the 3D glasses over your normal eye ware.  
• Do not keep your 3D glasses in extremely high or  
low temperatures. It will cause deformation.  
• Do not use the 3D glasses while walking or  
moving around. It may cause an accident or  
injury.  
• Be careful not to poke your eye with the frames  
of the 3D glasses.  
• Do not watch 3D content if you have  
photosensitive seizures, epilepsy, or heart  
disease.  
• Do not install this product on a wall if it could be  
exposed to oil or oil mist. This may damage the  
product and cause it to fall.  
• If the TV feels cold to the touch, there may  
be a small flicker when it is turned on. This is  
normal; there is nothing wrong with TV. Some  
minute dot defects may be visible on the screen,  
appearing as tiny red, green, or blue spots.  
However, they have no adverse effect on the  
TV’s performance. Avoid touching the screen or  
holding your finger(s) against it for long periods  
of time. Doing so may produce some temporary  
distortion effects on the screen.  
• Displaying a still image for a prolonged time may  
cause image sticking. Avoid displaying a fixed  
image on the TV screen for a long period of time.  
• Some horizontal lines may appear when the  
Clear Panel Noise feature is performed. It is  
normal and there is no need to be concerned.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparing  
CAUTION  
• Do not use any unapproved items to ensure the  
safety and product’s lifespan.  
• Any damages or injuries by using unapproved  
items are not covered by the warranty.  
• Some models appear to have a thin film on the  
screen. It is actually part of the screen; do not  
remove it.  
• When attaching the stand to the TV set, place  
the screen facing down on a cushioned table or  
flat surface to protect the screen from scratches.  
• Make sure that the screws are fastened tightly.  
(If they are not fastened securely enough, the TV  
may tilt forward after being installed.)  
• Do not fasten the screws with excessive force;  
otherwise, they may be worn out and become  
loose.  
NOTE  
• When the TV is turned on for the first time after  
being shipped from the factory, initialization of  
the TV may take approximately one minute.  
• Image shown may differ from your TV.  
• Your TV’s OSD (On Screen Display) may differ  
slightly from that shown in this manual.  
• The available menus and options may differ from  
the input source or product model that you are  
using.  
• New features may be added to this TV in the  
future.  
• The items supplied with your product may vary  
depending upon the model.  
• Product specifications or contents of this manual  
may be changed without prior notice due to  
upgrade of product functions.  
• For an optimal connection, HDMI cables and  
USB devices should have bezels less than 10 mm  
(0.39 inches) thick and 18 mm (0.7 inches) width.  
• Use an extension cable that supports USB 2.0 if  
the USB cable or USB flash drive does not fit into  
your TV’s USB port.  
• Make sure to wring any excess water or cleaner  
from the cloth.  
• Do not spray water or cleaner directly onto the  
TV screen.  
• Make sure to spray just enough of water or  
cleaner onto a dry cloth to wipe the screen.  
Optional Extras  
• Use a certified cable with the HDMI logo  
attached. If you do not use a certified HDMI  
cable, the screen may not display or a  
connection error may occur.  
Optional extras can be changed or modified for  
quality improvement without any notification.  
Contact your dealer for buying these items.  
These devices work only with certain models.  
The model name or design may be changed due to  
the manufacturer’s circumstances or policies.  
• Recommended HDMI cable types (3 m or less)  
- High-Speed HDMI®/TM cable  
- High-Speed HDMI ®/TM cable with Ethernet  
(Depending upon model)  
B
B
AG-F***  
AG-F***DP  
Cinema 3D Glasses  
Dual Play Glasses  
A
A
AN-MR650  
AN-VC550  
*A 10 mm (0.39 inches)  
*B 18 mm (0.7 inches)  
Magic Remote  
Smart Camera  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Lifting and Moving the TV  
Using the Button  
When moving or lifting the TV, read the following  
to prevent the TV from being scratched or  
damaged and for safe transportation regardless of  
its type and size.  
• It is recommended to move the TV in the box or  
packing material that the TV originally came in.  
• Before moving or lifting the TV, disconnect the  
power cord and all cables.  
(Depending upon model)  
You can simply operate the TV functions, pressing  
or moving the button.  
[A type]  
• When holding the TV, the screen  
should face away from you to  
avoid damage.  
Joystick Button  
• Hold the top and bottom of the TV frame firmly.  
Make sure not to hold the transparent part,  
speaker, or speaker grille area.  
[B type]  
Joystick Button  
• Use at least two people to move  
a large TV.  
• When transporting the TV by  
hand, hold the TV as shown in the  
following illustration.  
Basic Functions  
• When transporting the TV, do not expose the TV  
to jolts or excessive vibration.  
• When transporting the TV, keep the TV upright;  
never turn the TV on its side or tilt towards the  
left or right.  
• When handling the TV, be careful not to damage  
the protruding buttons.  
Power On (Press)  
Power Off (Press and Hold)1  
Volume Control  
Channels Control  
CAUTION  
1 All running apps will close.  
• Avoid touching the screen at all times, as this  
may result in damage to the screen.  
• Do not place the product on the floor with its  
front facing down without padding. Failure to do  
so may result in damage to the screen.  
• Do not move the TV by holding the cable  
holders, as the cable holders may break, and  
injuries and damage to the TV may occur.  
(Depending upon model)  
Adjusting the Menu  
When the TV is turned on, press button one time.  
You can adjust the Menu items pressing or moving  
the buttons.  
Turns the power off.  
Accesses the setting menu.  
Clears on-screen displays and returns to TV  
viewing.  
Changes the input source.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE  
Mounting on a Table  
• Use a platform or cabinet that is strong and large  
enough to support the TV securely.  
• Brackets, bolts, and ropes are optional. You can  
obtain additional accessories from your local  
dealer.  
1 Lift and tilt the TV into its upright position on a  
table.  
- Leave a 10 cm (4 inches) (minimum) space from  
the wall for proper ventilation.  
Mounting on a Wall  
10 cm  
(4 inches)  
An optional wall mount can be used with your  
LG Television. Consult with your local dealer for  
a wall mount that supports the VESA standard  
used by your TV model. Carefully attach the wall  
mount bracket at the rear of the TV. Install the wall  
mount bracket on a solid wall perpendicular to the  
floor. If you are attaching the TV to other building  
materials, please contact qualified personnel to  
install the wall mount. Detailed instructions will  
be included with the wall mount. We recommend  
that you use an LG brand wall mount. The LG wall  
mount is easy to adjust or to connect the cables.  
When you do not use LG’s wall mount bracket,  
use a wall mount bracket where the device is  
adequately secured to the wall with enough space  
to allow connectivity to external devices. If you are  
using a non-adjustable mount, attach the mount  
to the wall. Attach the cables to the TV first, then  
attach the TV to the mount.  
2 Connect the power cord to a wall outlet.  
CAUTION  
• Do not place the TV near or on sources of heat,  
as this may result in fire or other damage.  
Securing the TV to a Wall (optional)  
(Depending upon model)  
10 cm  
(4 inches)  
10 cm  
10 cm  
10 cm  
1 Insert and tighten the eye-bolts, or TV brackets  
and bolts on the back of the TV.  
- If there are bolts inserted at the eye-bolts  
position, remove the bolts first.  
2 Mount the wall brackets with the bolts to the  
wall. Match the location of the wall bracket and  
the eye-bolts on the rear of the TV.  
Make sure to use screws and wall mounts that  
meet the VESA standard. Standard dimensions for  
the wall mount kits are described in the following  
table.  
Model  
OLED55/65B6P OLED55/65C6P,  
OLED55/65E6P  
3 Connect the eye-bolts and wall brackets tightly  
with a sturdy rope or cable. Make sure to keep  
the rope parallel to the flat surface.  
VESA (A x B)  
Standard screw  
Number of  
screws  
300 x 200  
400 x 200  
M6  
4
CAUTION  
Wall mount  
bracket  
(optional)  
• Make sure that children do not climb on or hang  
on the TV.  
OTW420B  
A
B
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
• Depending upon the graphics card, some  
resolution settings may not allow the image to  
be positioned on the screen properly.  
• Some USB Hubs may not work. If a USB device  
connected through a USB Hub is not detected,  
connect it directly to the USB port on the TV.  
• The TV may be capable of operating without a  
set-top from a multichannel video programming  
distributor (MVPD).  
NOTE  
• Remove the stand before installing the TV on a  
wall mount by performing the stand attachment  
in reverse.  
CAUTION  
• To install the wall mount, use the stand assembly  
screws to attach the wall mount cover to the  
bottom of the product as shown in the following  
illustration. (For OLED55/65E6P)  
Connecting to an Antenna or Cable  
Provided Item  
Connect an antenna, cable, or cable box to watch  
TV. The illustrations may differ from the actual  
items and an RF cable is optional.  
Wall mount  
cover  
CAUTION  
X 2  
• Make sure not to bend the copper wire of the RF  
cable.  
Copper wire  
Connections (Notifications)  
• Complete all connections between devices, and  
then connect the power cord to the power outlet  
to prevent damage to your TV.  
You can connect various external devices to the TV.  
Supported external devices are: HD receivers, DVD  
players, VCRs, audio systems, USB storage devices,  
PC, gaming devices, and other external devices.  
For more information on an external device’s  
connection, refer to the manual provided with  
each device.  
NOTE  
• Use a signal splitter to use 2 TVs or more.  
• DTV Audio Supported Codec: MPEG,  
Dolby Digital.  
• Direct ULTRA HD broadcast is unavailable in  
areas without an ULTRA HD signal.  
• This TV cannot receive ULTRA HD (3840 x 2160  
pixels) broadcasts directly because the related  
standards have not been confirmed.  
(Depending upon model)  
NOTE  
• If you record a TV program on a DVD recorder or  
VCR, make sure to connect the TV signal input  
cable to the TV through a DVD recorder or VCR.  
For more information about recording, refer to  
the manual provided with the connected device.  
• The external device connections shown may  
differ slightly from illustrations in a manual.  
• Connect external devices to the TV regardless  
about the order of the TV port.  
• If you connect a gaming device to the TV, use the  
cable supplied with the gaming device.  
• Refer to the external equipment’s manual for  
operating instructions.  
• In PC mode, there may be noise associated  
with the resolution, vertical pattern, contrast,  
or brightness. If noise is present, change the PC  
output to another resolution, change the refresh  
rate to another rate, or adjust the brightness and  
contrast on the PICTURE menu until the picture  
is clear.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Connections  
Connect your TV to external devices. For the best  
picture and audio quality, connect the external  
device and the TV with the HDMI cable. Depending  
upon the model, a cable may not be provided.  
A
NOTE  
•
>
>
> General >  
HDMI ULTRA HD Deep Color:  
- On : Support 4K @ 60 Hz (4:4:4, 4:2:2, 4:2:0)  
- Off : Support 4K @ 60 Hz 8bit (4:2:0)  
B
• If the device connected to Input Port also  
supports ULTRA HD Deep Color, your picture  
may be clearer. However, if the device doesn’t  
support it, it may not work properly. In that case,  
connect the device to a different HDMI port or  
change the TV’s HDMI ULTRA HD Deep Color  
setting to Off.  
- This feature is available only on certain models  
which support HDMI ULTRA HD Deep Color.  
• HDMI Audio Supported Format:  
DTS (44.1 kHz / 48 kHz),  
AC3 (32 kHz / 44.1 kHz / 48 kHz),  
A
PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz /  
192 kHz) (Depending upon model)  
(POWER) Turns the TV on or off.  
You can turn your set-top box on or off  
by adding the set-top box to the universal remote  
control for your TV.  
Slim Remote Control  
Adjusts the volume level.  
(MUTE) Mutes all sounds.  
(Depending upon model)  
* Video descriptions function will be enabled.  
• SAP (Secondary Audio Program) Feature can also  
be enabled by pressing the  
The descriptions in this manual are based on  
the buttons on the remote control. Please read  
this manual carefully and use the TV correctly.  
To replace coin batteries, turn the battery cover  
counterclockwise by using a coin. Then, take the  
battery cover. Insert and fix the battery (CR2032)  
with the facing forward. And, Put the battery  
cover on the remote control and turn it clockwise  
to close.  
key.  
Scrolls through the saved channels.  
B
When in use, it should be pointed in the direction  
of the TV’s remote sensor.  
Returns to the previous screen.  
* Clears all on-screen displays and returns to  
TV viewing.  
(Home) Accesses the Home menu.  
(INPUT) Changes the input source.  
* Pressing and holding the (INPUT) button  
displays all the lists of external inputs.  
(Navigation buttons) Scrolls through  
menus or options. (up/down/left/right)  
Selects menus or options and confirms your  
input.  
* : To use the button, press and hold for more than  
3 seconds.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Battery Installation  
A
WARNING  
DO NOT INGEST BATTERY. CHEMICAL BURN  
HAZARD.  
CAUTION  
• The battery used in this device may present a  
fire or chemical burn hazard if mistreated. Do  
not recharge, disassemble, incinerate, or heat  
above 100 °C (212 °F). Replace the battery part  
no. CR2032 only. Use of another battery may  
present a risk of fire or explosion. Dispose of  
used battery. Keep battery away from children.  
Do not disassemble or dispose of in fire.  
• [The remote control supplied with] This product  
contains a coin/button cell battery. If the coin/  
button cell battery is swallowed, it can cause  
severe internal burns in just 2 hours and can lead  
to death. Keep new and used batteries away  
from children. If the battery compartment does  
not close securely, stop using the product and  
keep it away from children. If you think batteries  
might have been swallowed or placed inside  
any part of the body, seek immediate medical  
attention.  
B
C
• If you have long nails, do not open the battery  
cover by using your finger. Or else, your nail  
could break.  
A
(POWER) Turns the TV on or off.  
/
You can turn your set-top box on  
or off by adding the set-top box to the universal  
remote control for your TV.  
Magic Remote Functions  
Number button Enters numbers.  
(Depending upon model)  
- (Dash) Inserts a dash between numbers such as  
2-1 and 2-2.  
When the message Magic remote battery is low.  
Change the battery. is displayed, replace the  
battery. To install batteries, open the battery cover,  
replace batteries (1.5 V AA) matching and  
ends to the label inside the compartment, and  
close the battery cover. Failure to match the correct  
polarities of the battery may cause the battery to  
burst or leak, resulting in fire, personal injury, or  
ambient pollution. Be sure to point the remote  
control at the remote control sensor on the TV.  
To remove the batteries, perform the installation  
actions in reverse.  
Accesses the saved channel list.  
(Screen Remote) Displays the Screen Remote.  
• Accesses the Universal Control Menu in some  
regions.  
This remote uses infrared light. When in use, it  
should be pointed in the direction of the TV’s  
remote sensor.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Color buttons These access special functions in  
B
some menus.  
(
Red,  
Green,  
Yellow,  
Blue)  
Adjusts the volume level.  
(MUTE) Mutes all sounds.  
* Video descriptions function will be enabled.  
• SAP (Secondary Audio Program) Feature can also  
be enabled by pressing the key.  
,
/
,
,
,
Control buttons for media  
contents (Depending upon model)  
You can zoom in on the area where the  
remote control is pointed.  
* By zooming in on the selected area,  
you can view it in full screen.  
Scrolls through the saved channels.  
(Home) Accesses the Home menu.  
* Shows the previous history.  
* : To use the button, press and hold for more than  
3 seconds.  
(Search) Search for content such as channels,  
movies and other videos, or perform a web search  
by entering your search terms in the search box.  
Registering Magic Remote  
(Voice recognition) * Network connection is  
required to use the voice recognition function.  
How to Register the Magic Remote  
1 Press the (Voice recognition) button.  
To use the Magic Remote, first pair it with your TV.  
2 Speak when the voice display window appears  
on the TV screen.  
1 Put batteries into the Magic Remote and turn the  
TV on.  
Displays the set-top box Home menu.  
(When you are not watching with a set-top box:  
the set-top box screen is displayed.)  
2 Point the Magic Remote at your TV and press the  
(Wheel) (OK) on the remote control.  
• If the TV fails to register the Magic Remote, try  
again after turning the TV off and back on.  
How to Deregister the Magic Remote  
C
Press the  
/
and  
(Home) buttons  
at the same time, for five seconds, to unpair the  
Magic Remote with your TV.  
/
(Navigation buttons) Press the  
up, down, left or right button to scroll the menu.  
(up/down/left/right)  
• Pressing and holding the  
button will  
let you cancel and re-register Magic Remote at  
once.  
If you press  
/
buttons while the  
pointer is in use, the pointer will disappear from  
the screen and Magic Remote will operate like a  
general remote control. To display the pointer on  
the screen again, shake Magic Remote to the left  
and right.  
Licenses  
(Wheel) (OK) Press the center of the Wheel  
button to select a menu. You can change channels  
by using the Wheel button.  
Supported licenses may differ by model.  
For more information about licenses,  
visit www.lg.com. (Depending upon model)  
Returns to the previous screen.  
* Clears all on-screen displays and returns to  
TV viewing.  
Used for viewing 3D video. (For 3D models)  
(INpUT) Changes the input source.  
* Pressing and holding the (INpUT) button  
displays all the lists of external inputs.  
Activates or deactivates the subtitles.  
Displays the program event according to  
time scheduler. (Depending upon model)  
(Q. Settings) Accesses the quick settings.  
* Pressing and holding the (Q. Settings) button  
displays the All Settings menu.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Open Source Software Notice  
Information  
Specifications  
Product specifications may be changed without  
prior notice due to upgrade of product functions.  
Estimated yearly energy consumption indicated on  
the FTC label is measured in accordance with the  
Test Procedures for Television Sets (USA only).  
The actual energy consumption depends on the  
usage environment (The content watched, TV  
settings, etc.).  
To obtain the source code under GPL, LGPL, MPL,  
and other open source licenses, that is contained in  
this product, please visit http://opensource.lge.com.  
In addition to the source code, all referred license  
terms, warranty disclaimers and copyright notices  
are available for download. LG Electronics will also  
provide open source code to you on CD-ROM for  
a charge covering the cost of performing such  
distribution (such as the cost of media, shipping,  
and handling) upon email request to opensource@  
lge.com. This offer is valid for three (3) years from  
the date on which you purchased the product.  
Television System  
ATSC, NTSC-M, 64 & 256 QAM  
Program Coverage  
External Control Device Setup  
VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135,  
CADTV 1-135  
To obtain the external control device setup  
information, please visit www.lg.com.  
(Depending upon model)  
External Antenna Impedance  
75 Ω  
Troubleshooting  
• Cannot control the TV with the remote control.  
- Check if anything such as tape has been placed  
over the receiver.  
- Check if there is any obstacle between the  
product and the remote control.  
- Replace the batteries with new ones.  
• No image display and no sound is produced.  
- Check if the product is turned on.  
- Check if the power cord is connected to a wall  
outlet.  
Environment Condition  
• Operating Temperature  
0 °C to 40 °C (32 °F to 104 °F)  
• Operating Humidity  
Less than 80 %  
• Storage Temperature  
- 20 °C to 60 °C (-4 °F to 140 °F)  
• Storage Humidity  
Less than 85 %  
- Check if there is a problem in the wall outlet by  
connecting other products.  
• The TV turns off suddenly.  
- Check the power control settings. The power  
supply may be interrupted.  
- Check if the Sleep Timer / Timer Power Off  
feature is activated in the Timers settings.  
- If there is no signal while the TV is on, the TV  
will turn off automatically after 15 minutes of  
inactivity.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wireless Module (LGSBWAC61)  
Specifications  
Wireless LAN (IEEE 802.11a/b/g/n/ac)  
Frequency Range  
2400 to 2483.5 MHz  
5150 to 5725 MHz  
5725 to 5850 MHz  
Output Power (Max.)  
15 dBm  
16 dBm  
12.5 dBm  
Bluetooth  
Frequency Range  
Output Power (Max.)  
2400 to 2483.5 MHz  
10 dBm  
• As band channels can vary per country, the  
user cannot change or adjust the operating  
frequency. This product is configured for the  
regional frequency table.  
• For consideration of the user, this device should  
be installed and operated with a minimum  
distance of 20 cm (7.8 inches) between the  
device and the body.  
• FCC ID: BEJLGSBWAC61  
IC: 2703H-LGSBWAC61  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC RF Radiation Exposure Statement  
Regulatory  
[For having wireless function (WLAN, Bluetooth,...)]  
This equipment complies with FCC radiation  
exposure limits set forth for an uncontrolled  
environment. This transmitter must not be co-  
located or operating in conjunction with any other  
antenna or transmitter.  
FCC Notice  
(For USA)  
This equipment should be installed and operated  
with minimum distance 20 cm (7.8 inches)  
between the antenna and your body. Users must  
follow the specific operating instructions for  
satisfying RF exposure compliance.  
This equipment has been tested and found to  
comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection  
against harmful interference in a residential  
installation. This equipment generates, uses,  
and can radiate radio frequency energy and, if  
not installed and used in accordance with the  
instructions, may cause harmful interference  
to radio communications. However, there is no  
guarantee that interference will not occur in a  
particular installation. If this equipment does  
cause harmful interference to radio or television  
reception, which can be determined by turning  
the equipment off and on, the user is encouraged  
to try to correct the interference by one or more of  
the following measures:  
Industry Canada Statement  
(For Canada)  
[For having wireless function (WLAN, Bluetooth,...)]  
This device complies with Industry Canada’s  
licence-exempt RSSs. Operation is subject to the  
following two conditions:  
1 This device may not cause interference; and  
2 This device must accept any interference,  
including interference that may cause undesired  
operation of the device.  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the  
equipment and the receiver.  
- Connect the equipment to an outlet on a circuit  
different from that to which the receiver is  
connected.  
- Consult the dealer or an experienced radio/TV  
technician for help.  
IC Radiation Exposure Statement  
(For Canada)  
This device complies with part 15 of the FCC  
Rules. Operation is subject to the following two  
conditions: (1) this device may not cause harmful  
interference and (2) this device must accept any  
interference received, including interference that  
may cause undesired operation of the device.  
Any changes or modifications in construction of  
this device which are not expressly approved by  
the party responsible for compliance could void  
the user’s authority to operate the equipment.  
[For having wireless function (WLAN, Bluetooth,...)]  
This equipment complies with IC radiation  
exposure limits set forth for an uncontrolled  
environment. This equipment should be installed  
and operated with minimum distance 20 cm (7.8  
inches) between the antenna & your body.  
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE  
FOR ANY RADIO OR TV INTERFERENCE CAUSED  
BY UNAUTHORIZED MODIFICATIONS TO THIS  
EQUIPMENT. SUCH MODIFICATIONS COULD  
VOID THE USER’S AUTHORITY TO OPERATE THE  
EQUIPMENT.  
FCC Radio Frequency Interference  
Requirements (for UNII devices)  
High power radars are allocated as primary users  
of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands.  
These radar stations can cause interference with  
and/or damage this device. This device cannot be  
co-located with any other transmitter.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING!  
WARNING  
(For Canada)  
[For product having the wireless function using 5  
GHz frequency bands]  
1 The device for operation in the band 5150–5250  
MHz is only for indoor use to reduce the  
potential for harmful interference to co-channel  
mobile satellite systems;  
Never place a television set in an unstable  
location. A television set may fall, causing serious  
personal injury or death. Many injuries, particularly  
to children, can be avoided by taking simple  
precautions such as:  
• Using cabinets or stands recommended by the  
manufacturer of the television set.  
• Only using furniture that can safely support the  
television set.  
2 For devices with detachable antenna(s), the  
maximum antenna gain permitted for devices in  
the bands 5250-5350 MHz and 5470-5725 MHz  
shall be such that the equipment still complies  
with the e.i.r.p. limit;  
• Ensuring the television set is not overhanging  
the edge of the supporting furniture.  
• Not placing the television set on tall furniture  
(for example, cupboards or bookcases) without  
anchoring both the furniture and the television  
set to a suitable support.  
• Not placing the television set on cloth or other  
materials that may be located between the  
television set and supporting furniture.  
• Educating children about the dangers of  
climbing on furniture to reach the television set  
or its controls.  
3 For devices with detachable antenna(s), the  
maximum antenna gain permitted for devices in  
the band 5725-5850 MHz shall be such that the  
equipment still complies with the e.i.r.p. limits  
specified for point-to-point and non-point-to-  
point operation as appropriate; and  
4 The worst-case tilt angle(s) necessary to remain  
compliant with the e.i.r.p. elevation mask  
requirement set forth in Section 6.2.2(3) shall be  
clearly indicated.(devices operating in the band  
5250-5350 MHz with a maximum e.i.r.p. greater  
than 200 mW)  
If your existing television set is being retained  
and relocated, the same considerations as above  
should be applied.  
5 High-power radars are allocated as primary  
users (i.e. priority users) of the bands 5250–5350  
MHz and 5650–5850 MHz and that these radars  
could cause interference and/or damage to LE-  
LAN devices.  
Symbols  
Refers to alternating current(AC).  
Refers to direct current(DC).  
Refers to class II equipment.  
Refers to stand-by.  
Note to Cable/TV Installer  
(For USA and Canada)  
Refers to “ON” (power).  
This reminder is provided to call the CATV system  
installer’s attention to Article 820-40 of the  
Refers to dangerous voltage.  
National Electric Code (U.S.A.). The code provides  
guidelines for proper grounding and, in particular,  
specifies that the cable ground shall be connected  
to the grounding system of the building, as close  
to the point of the cable entry as practical.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHILD SAFETY:  
PROPER TELEVISION PLACEMENT MATTERS  
THE CONSUMER ELECTRONICS INDUSTRY CARES  
• Manufacturers, retailers and the rest of the consumer electronics industry are committed to  
making home entertainment safe and enjoyable.  
• As you enjoy your television, please note that all televisions – new and old- must be supported on  
proper stands or installed according to the manufacturer’s recommendations. Televisions that  
are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests, carts, etc.,  
may fall over, resulting in injury.  
TUNE IN TO SAFETY  
• ALWAYS follow the manufacturer’s recommendations for the safe installation of your television.  
• ALWAYS read and follow all instructions for proper use of your television.  
• NEVER allow children to climb on or play on the television or the furniture on which the television  
is placed.  
• NEVER place the television on furniture that can easily be used as steps, such as a chest of  
drawers.  
• ALWAYS install the television where it cannot be pushed, pulled over or knocked down.  
• ALWAYS route cords and cables connected to the television so that they cannot be tripped  
over, pulled or grabbed.  
WALL OR CEILING MOUNT YOUR TELEVISION  
• ALWAYS contact your retailer about professional installation if you have any doubts about your  
ability to safely mount your television.  
• ALWAYS use a mount that has been recommended by the television manufacturer and has a  
safety certification by an independent laboratory (such as UL, CSA, ETL).  
• ALWAYS follow all instructions supplied by the television and mount manufacturers.  
• ALWAYS make sure that the wall or ceiling where you are mounting the television is appropriate.  
Some mounts are not designed to be mounted to walls and ceilings with steel studs or cinder  
block construction. If you are unsure, contact a professional installer.  
• Televisions can be heavy. A minimum of two people is required for a wall or ceiling mount  
installation.  
MOVING AN OLDER TELEVISION TO A NEW PLACE IN  
YOUR HOME  
• Many new television buyers move their older CRT televisions into a secondary room after the  
purchase of a flat-panel television. Special care should be made in the placement of older CRT  
televisions.  
• ALWAYS place your older CRT television on furniture that is sturdy and appropriate for its size  
and weight.  
• NEVER place your older CRT television on a dresser where children may be tempted to use the  
drawers to climb.  
• ALWAYS make sure your older CRT television does not hang over the edge of your furniture.  
CE.org/safety  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Declaration of Conformity  
Trade Name LG  
Model  
OLED55B6P-U, OLED65B6P-U  
OLED55C6P-U, OLED65C6P-U  
OLED55E6P-U, OLED65E6P-U  
Responsible LG Electronics Inc.  
Party  
Address  
1000 Sylvan Ave.  
Englewood Cliffs NJ 07632  
U.S.A  
TEL  
201 - 266 - 2534  
LG Customer Information Center  
For inquires or comments, visit www.lg.com or call;  
The model and serial numbers of the TV are located on the  
back and one side of the TV.  
Record them below should you ever need service.  
1-800-243-0000  
1-888-865-3026  
1-888-542-2623  
USA, Consumer User  
USA, Commercial User  
CANADA  
Register your product online!  
www.lg.com  
MODEL  
SERIAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S MANUAL  
EXTERNAL CONTROL  
DEVICE SETUP  
Please read this manual carefully before operating the set and retain it for  
future reference.  
www.lg.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KEY CODES  
2
KEY CODES  
• This feature is not available for all models.  
Code  
(Hexa)  
Code  
(Hexa)  
Function  
CH +, PR +  
Note  
Function  
Note  
00  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
53  
5B  
60  
61  
63  
71  
72  
79  
91  
7A  
7C  
7E  
8E  
8F  
AA  
AB  
B0  
B1  
List  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
01  
CH -, PR -  
Volume +  
Exit  
02  
PIP(AD)  
Blue  
03  
Volume -  
06  
> (Arrow Key / Right Key)  
< (Arrow Key / Left Key)  
Power  
Yellow  
Green  
Red  
07  
08  
09  
Mute  
Ratio / Aspect Ratio  
AD (Audio Description)  
User Guide  
0B  
0E  
0F  
Input  
SLEEP  
TV, TV/RAD  
Smart / Home  
SIMPLINK  
10 - 19 * Number Key 0 - 9  
1A  
1E  
20  
21  
28  
30  
Q.View / Flashback  
FAV (Favorite Channel)  
Text (Teletext)  
►► (Forward)  
◄◄ (Rewind)  
Info  
T. Opt (Teletext Option)  
Return (BACK)  
Program Guide  
► (Play)  
AV (Audio / Video) Mode  
ꕗ (Stop / File List)  
ꕘ (Freeze / Slow Play /  
39  
40  
41  
Caption/Subtitle  
R/C Button  
R/C Button  
R/C Button  
BA  
BB  
BD  
R/C Button  
R/C Button  
R/C Button  
Pause)  
Λ
(Arrow Key / Cursor Up)  
Soccer  
V (Arrow Key / Cursor  
Down)  
ꔄ (REC)  
42  
43  
44  
45  
4C  
My Apps  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
R/C Button  
DC  
99  
3D  
R/C Button  
R/C Button  
R/C Button  
Menu / Settings  
OK / Enter  
AutoConfig  
App / *  
9F  
Q.Menu  
List, - (ATSC Only)  
* Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel.  
(For South Korea, Japan, North America, Latin America except Colombia models)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXTERNAL CONTROL DEVICE SETUP  
3
EXTERNAL CONTROL DEVICE SETUP  
• Image shown may differ from your TV.  
Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer  
or an A/V control system) to control the product’s functions externally.  
Note: The type of control port on the TV can be different between model series.  
* Please be advised that not all models support this type of connectivity.  
* Cable is not provided.  
USB to Serial converter with USB Cable  
USB Type  
(TV)  
(PC)  
• LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial converter  
which is not made nor provided by LG.  
• It can be purchased from computer stores that carry accessories for IT support professionals.  
RS-232C With RS232C Cable  
DE9 (D-Sub 9pin) Type  
• You need to purchase the RS-232C (DE9, D-Sub 9pin female-to-female type) to RS-232C cable required  
for the connection between the PC and the TV, which is specified in the manual.  
RS-232C IN  
(CONTROL & SERVICE)  
(PC)  
(TV)  
The connection interface may differ from your TV.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXTERNAL CONTROL DEVICE SETUP  
4
Phone jack Type  
• You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and  
the TV, which is specified in the manual.  
* For other models, connect to the USB port.  
* The connection interface may differ from your TV.  
1
3
(PC)  
(TV)  
(TV)  
2
- or  
1
3
(PC)  
RS-232C IN  
(CONTROL & SERVICE)  
2
Customer Computer  
RS-232C configurations  
3-Wire Configurations(Not standard)  
1
5
PC  
TV  
RXD  
TXD  
GND  
2
3
5
2
1
3
TXD  
RXD  
GND  
OR  
6
9
RXD  
TXD  
GND  
3
2
5
2
1
3
TXD  
RXD  
GND  
RS-232C  
(Serial port)  
D-Sub 9  
Phone  
Set ID  
For Set ID number, see "Real Data Mapping" on p.6  
1. Press SETTINGS to access the main menus.  
2. Press the Navigation buttons to scroll to (*General → About this TV or OPTION) and press OK.  
3. Press the Navigation buttons to scroll to SET ID and press OK.  
4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.  
5. When you are finished, press EXIT.  
* (Depending on model)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXTERNAL CONTROL DEVICE SETUP  
5
Communication Parameters  
• Baud rate : 9600 bps (UART)  
• Data length : 8 bits  
• Parity : None  
• Stop bit : 1 bit  
• Communication code : ASCII code  
• Use a crossed (reverse) cable.  
Command reference list  
(Depending on model)  
DATA  
(Hexadecimal)  
DATA  
(Hexadecimal)  
COMMAND1 COMMAND2  
COMMAND1 COMMAND2  
01. Power*  
k
k
a
c
00 to 01  
15. Balance  
k
x
t
00 to 64  
16. Color  
(Colour)  
Temperature  
02. Aspect  
Ratio  
(p.7)  
(p.7)  
u
00 to 64  
(p.8)  
17. ISM  
Method (Only j  
Plasma TV)  
03. Screen  
Mute  
k
d
p
04. Volume  
Mute  
k
k
k
e
f
00 to 01  
00 to 64  
00 to 64  
18. Equalizer j  
v
(p.8)  
05. Volume  
Control  
19. Energy  
Saving  
j
q
00 to 05  
20. Tune  
Command  
06. Contrast  
g
m
a
b
(p.9)  
21. Channel  
(Programme)  
Add/Del(Skip)  
m
00 to 01  
07.  
Brightness  
k
k
h
i
00 to 64  
00 to 64  
08. Color/  
Colour  
22. Key  
m
m
c
Key Codes  
00 to 64  
23. Control  
Backlight,  
Control Panel  
Light  
g
09. Tint  
k
j
00 to 64  
10.  
Sharpness  
24. Input  
select (Main)  
x
x
b
t
(p.11)  
(p.11)  
(p.11)  
k
k
k
l
00 to 32  
00 to 01  
11. OSD  
Select  
25. 3D (Only  
3D models)  
12. Remote  
Control Lock  
Mode  
26. Extended x  
3D (Only 3D  
models)  
v
k
k
k
m
r
00 to 01  
00 to 64  
00 to 64  
27. Auto  
Configure  
j
u
(p.12)  
13. Treble  
14. Bass  
s
* Note: During playing or recording media, all commands except Power (ka) and Key (mc) are not  
executed and treated as NG.  
With RS232C cable, TV can communicate "ka command" in power-on or power-off status. but with  
USB-to-Serial converter cable, the command works only if TV is on.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXTERNAL CONTROL DEVICE SETUP  
6
Transmission / Receiving Protocol  
Transmission  
[Command1][Command2][ ][Set ID][ ][Data][Cr]  
[Command 1] : First command to control the TV. (j, k, m or x)  
[Command 2] : Second command to control the TV.  
[Set ID]  
: You can adjust the [Set ID] to choose desired monitor ID number in option menu.  
Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set  
can be controlled.  
* [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on  
transmission/receiving protocol.  
[DATA]  
[Cr]  
: To transmit command data (hexadecimal). Transmit ‘FF’ data to read status of command.  
: Carriage Return - ASCII code ‘0x0D’  
[ ]  
: Space – ASCII code ‘0x20’  
OK Acknowledgement  
[Command2][ ][Set ID][ ][OK][Data][x]  
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,  
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the  
data of the PC computer.  
Error Acknowledgement  
[Command2][ ][Set ID][ ][NG][Data][x]  
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from  
non-viable functions or communication errors.  
Data 00: Illegal Code  
Real data mapping (Hexadecimal b Decimal)  
* When you enter the [data] in hexadecimal, refer to following conversion table.  
* Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.  
00 : Step 0  
01 : Step 1 (Set ID 1)  
32 : Step 50 (Set ID 50)  
33 : Step 51 (Set ID 51)  
FE : Step 254  
FF : Step 255  
...  
...  
...  
0A : Step 10 (Set ID 10)  
63 : Step 99 (Set ID 99)  
01 00 : Step 256  
...  
...  
...  
0F : Step 15 (Set ID 15)  
10 : Step 16 (Set ID 16)  
...  
C7 : Step 199  
C8 : Step 200  
...  
27 0E : Step 9998  
27 0F : Step 9999  
...  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXTERNAL CONTROL DEVICE SETUP  
7
* Commands may work differently depending on model and signal.  
01. Power (Command: k a)  
Ack [d][ ][Set ID][ ][OK/NG][Data][x]  
► To control Power *On or Off of the set.  
Transmission[k][a][ ][Set ID][ ][Data][Cr]  
* In case of video mute on only, TV will display On  
Screen Display(OSD). But, in case of Screen mute  
on, TV will not display OSD.  
Data 00 : Power Off  
01 : *Power On  
Ack [a][ ][Set ID][ ][OK/NG][Data][x]  
04. Volume Mute (Command: k e)  
► To Show TV is Power On or *Off  
Transmission [k][a][ ][Set ID][ ][FF][Cr]  
Ack [a][ ][Set ID][ ][OK][Data][x]  
► To control volume mute on/off.  
You can also adjust mute using the MUTE button  
on remote control.  
Transmission [k][e][ ][Set ID][ ][Data][Cr]  
* Similarly, if other functions transmit ‘FF’ data  
based on this format, Acknowledgement feedback  
presents status about each function.  
Data 00 : Volume mute on (Volume off)  
01 : Volume mute off (Volume on)  
Ack [e][ ][Set ID][ ][OK/NG][Data][x]  
02. Aspect Ratio (Command: k c)  
(Main Picture Size)  
05. Volume Control (Command: k f)  
► To adjust the screen format. (Main picture format)  
You can also adjust the screen format using the  
Aspect Ratio in the Q.MENU. or PICTURE menu.  
► To adjust volume.  
You can also adjust volume with the volume  
buttons on remote control.  
Transmission [k][f][ ][Set ID][ ][Data][Cr]  
Transmission [k][c][ ][Set ID][ ][Data][Cr]  
Data 01 : Normal screen 07 : 14:9  
Data Min : 00 to Max : 64  
(4:3)  
02 : Wide screen  
(16:9)  
(Europe, Colombia, Mid-East,  
Asia except South Korea and  
Japan)  
Ack [f][ ][Set ID][ ][OK/NG][Data][x]  
04 : Zoom  
09 : * Just Scan  
0B : Full Wide  
(Europe, Colombia, Mid-  
East, Asia except South  
Korea and Japan)  
06. Contrast (Command: k g)  
05 : Zoom 2  
(Latin America  
except Colombia  
Only)  
► To adjust screen contrast.  
You can also adjust contrast in the PICTURE  
menu.  
06 : Set by Program/ 10 to 1F : Cinema Zoom 1 to 16  
Original 0c : 21:9 (Depending on model)  
Transmission [k][g][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
Ack [c][ ][Set ID][ ][OK/NG][Data][x]  
Ack [g][ ][Set ID][ ][OK/NG][Data][x]  
* Using the PC input, you select either 16:9 or 4:3  
screen aspect ratio.  
* In DTV/HDMI/Component mode (high-definition),  
Just Scan is available.  
07. Brightness (Command: k h)  
► To adjust screen brightness.  
You can also adjust brightness in the PICTURE  
menu.  
* Full wide mode may work differently based on  
model and is supported for DTV fully, and ATV,  
AV partially.  
Transmission [k][h][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
03. Screen Mute (Command: k d)  
► To select screen mute on/off.  
Ack [h][ ][Set ID][ ][OK/NG][Data][x]  
Transmission [k][d][ ][Set ID][ ][Data][Cr]  
08. Color/Colour (Command: k i)  
Data 00 : Screen mute off (Picture on)  
Video mute off  
► To adjust the screen Color(Colour).  
01 : Screen mute on (Picture off)  
10 : Video mute on  
You can also adjust colour in the PICTURE menu.  
Transmission [k][i][ ][Set ID][ ][Data][Cr]  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXTERNAL CONTROL DEVICE SETUP  
8
Data Min : 00 to Max : 64  
* (Depending on model)  
Ack [i][ ][Set ID][ ][OK/NG][Data][x]  
14. Bass (Command: k s)  
09. Tint (Command: k j)  
► To adjust Bass.  
► To adjust the screen tint.  
You can also adjust in the AUDIO menu.  
You can also adjust tint in the PICTURE menu.  
Transmission [k][s][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
Transmission [k][j][ ][Set ID][ ][Data][Cr]  
Data Red : 00 to Green : 64  
Ack [s][ ][Set ID][ ][OK/NG][Data][x]  
Ack [j][ ][Set ID][ ][OK/NG][Data][x]  
* (Depending on model)  
15. Balance (Command: k t)  
10. Sharpness (Command: k k)  
► To adjust balance.  
► To adjust the screen sharpness.  
You can also adjust sharpness in the PICTURE  
menu.  
You can also adjust balance in the AUDIO menu.  
Transmission [k][t][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
Transmission [k][k][ ][Set ID][ ][Data][Cr]  
Ack [t][ ][Set ID][ ][OK/NG][Data][x]  
Data Min : 00 to Max : 32  
Ack [k][ ][Set ID][ ][OK/NG][Data][x]  
16. Color(Colour) Temperature (Command: x u)  
► To adjust colour temperature. You can also adjust  
11. OSD Select (Command: k l)  
Color(Colour) Temperature in the PICTURE menu.  
► To select OSD (On Screen Display) on/off when  
Transmission [x][u][ ][Set ID][ ][Data][Cr]  
controlling remotely.  
Data Min : 00 to Max : 64  
Transmission [k][l][ ][Set ID][ ][Data][Cr]  
Ack [u][ ][Set ID][ ][OK/NG][Data][x]  
Data 00 : OSD off  
01 : OSD on  
Ack [l][ ][Set ID][ ][OK/NG][Data][x]  
17. ISM Method (Command: j p) (Only Plasma TV)  
► To control the ISM method. You can also adjust  
12. Remote control lock mode (Command: k m)  
ISM Method in OPTION menu.  
► To lock the front panel controls on the monitor and  
Transmission [j][p][ ][Set ID][ ][Data][Cr]  
remote control.  
Data Min : 02: Orbiter  
08: Normal  
Transmission [k][m][ ][Set ID][ ][Data][Cr]  
20: Color(Colour) Wash  
Data 00 : Lock off  
01 : Lock on  
Ack [p][ ][Set ID][ ][OK/NG][Data][x]  
Ack [m][ ][Set ID][ ][OK/NG][Data][x]  
* If you are not using the remote control, use this  
mode.  
18. Equalizer (Command : j v)  
When main power is off & on (plug-off and plug-in,  
after 20 - 30 seconds), external control lock is  
released.  
► Adjust EQ of the set.  
Transmission [j][v][ ][Set ID][ ][Data][Cr]  
MSB  
0
LSB  
0
* In the standby mode (DC off by off timer or ‘ka’,  
‘mc’ command), and if key lock is on, TV will not  
turn on by power on key of IR & Local Key.  
0
0
0
0
0
0
Frequency  
Data  
13. Treble (Command: k r)  
► To adjust treble.  
Frequency  
1st Band  
2nd Band  
3rd Band  
4th Band  
7
0
0
0
0
6
0
0
1
1
5
0
1
0
1
4
3
2
0
0
...  
1
0
0
1
...  
Step  
You can also adjust in the AUDIO menu.  
0
0
...  
0
0
...  
0
0
...  
0(decimal)  
1(decimal)  
...  
Transmission [k][r][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
Ack [r][ ][Set ID][ ][OK/NG][Data][x]  
19(decimal)  
0
0
0
1
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXTERNAL CONTROL DEVICE SETUP  
9
Set ID = All = 00  
5th Band  
20(decimal)  
1
0
0
0
0
1
0
1
Data 00 & 01 = Channel Data is 10 = 00 0a  
Data 02 = Analog Antenna TV = 00  
Result = ma 00 00 0a 00  
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]  
* It depends on model, and can adjust when sound  
mode is EQ adjustable value.  
2. Tune to the digital antenna (DVB-T) Channel 01.  
Set ID = All = 00  
Data 00 & 01 = Channel Data is 1 = 00 01  
Data 02 = Digital Antenna TV = 10  
Result = ma 00 00 01 10  
19. Energy Saving (Command: j q)  
► To reduce the power consumption of the TV. You  
can also adjust Energy Saving in PICTURE menu.  
Transmission [j][q][ ][Set ID][ ][Data][Cr]  
3. Tune to the satellite (DVB-S) Channel 1000.  
Set ID = All = 00  
Data  
00 : Off  
01 : Minimum  
02 : Medium  
Data 00 & 01 = Channel Data is 1000 = 03 E8  
Data 02 = Digital Satellite TV = 40  
Result = ma 00 03 E8 40  
03 : Maximum  
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]  
[Data 02][x][a][ ][Set ID][ ][NG][Data 00][x]  
04 : Auto (For LCD TV / LED TV) /  
Intelligent sensor (For PDP TV)  
05 : Screen off  
• For South Korea, North/Latin America except  
Colombia Model  
* (Depending on model)  
Ack [q][ ][Set ID][ ][OK/NG][Data][x]  
► To tune channel to following physical/major/minor  
number.  
Transmission [m][a][ ][0][ ][Data00][ ][Data01]  
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]  
20. Tune Command (Command: m a)  
Digital channels have a Physical, Major, and Minor  
channel number. The Physical number is the actual  
digital channel number, the Major is the number that  
the channel should be mapped to, and the Minor is  
* This command may work differently depending on  
model and signal.  
• For Europe, Mid-East, Colombia, Asia except  
South Korea and Japan Model  
the sub-channel. Since the ATSC tuner automatically  
maps the channel from the Major / Minor number,  
the Physical number is not required when sending a  
command in Digital.  
► Select channel to following physical number.  
Transmission [m][a][ ][Set ID][ ][Data 00][ ]  
[Data 01][ ][Data 02][Cr]  
* Analog Antenna/Cable  
* Analog Antenna/Cable  
Data 00 : Physical Channel Number  
[Data 00][Data 01] Channel Data  
Data 00 : High byte channel data  
Data 01 : Low byte channel data  
- 00 00 ~ 00 C7 (Decimal : 0 ~ 199)  
- Antenna (ATV) : 02~45 (Decimal: 2 ~ 69)  
- Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)  
[Data 01 ~ 04]: Major/Minor Channel Number  
Data 01 & 02: xx (Don't care)  
Data 03 & 04: xx (Don't care)  
Data 05: Input Source (Analog)  
- 00 : Antenna TV (ATV)  
Data 02 : Input Source (Analog)  
- 00 : Antenna TV (ATV)  
- 80 : Cable TV (CATV)  
* Digital Antenna/Cable/Satellite  
- 01 : Cable TV (CATV)  
* Digital Antenna/Cable  
[Data 00][Data 01]: Channel Data  
Data 00 : High Channel data  
Data 01 : Low Channel data  
Data 00 : xx (Don't care)  
- 00 00 ~ 27 0F (Decimal: 0 ~ 9999)  
[Data 01][Data 02]: Major Channel Number  
Data 01 : High byte Channel Data  
Data 02 : Low byte Channel Data  
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)  
[Data 03][Data 04]: Minor Channel Number  
Data 03 : High byte Channel Data  
Data 04 : Low byte Channel Data  
Data 02 : Input Source (Digital)  
- 10 : Antenna TV (DTV)  
- 20 : Antenna Radio (Radio)  
- 40 : Satellite TV (SDTV)  
- 50 : Satellite Radio (S-Radio)  
- 90 : Cable TV (CADTV)  
- a0 : Cable Radio (CA-Radio)  
Data 05 : Input Source (Digital)  
- 02 : Antenna TV (DTV) – Use Physical Channel  
Number  
- 06 : Cable TV (CADTV) – Use Physical Channel  
* Tune Command Examples:  
1. Tune to the Analog antenna (PAL) Channel 10.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXTERNAL CONTROL DEVICE SETUP  
10  
Number  
Data 05 = Digital Antenna TV = 02  
- 22 : Antenna TV (DTV) – Don’t Use Physical  
Channel Number  
Total = ma 00 00 00 11 00 01 02  
- 26 : Cable TV (CADTV) - Don’t Use Physical  
Channel Number  
- 46 : Cable TV (CADTV) – Use Major Channel  
Number Only (One Part Channel)  
2. Tune to the BS (ISDB-BS) channel 30.  
Set ID = All = 00  
Data 00 = Don’t know Physical = 00  
Data 01 & 02 = Major is 30 = 00 1E  
Data 03 & 04 = Don’t Care = 00 00  
Data 05 = Digital BS TV = 07  
Two bytes are available for each major and minor  
channel data, but usually the low byte is used alone  
(high byte is 0).  
Total = ma 00 00 00 1E 00 00 07  
* Tune Command Examples:  
1. Tune to the Analog cable (NTSC) channel 35.  
Set ID = All = 00  
Data 00 = Channel Data is 35 = 23  
Data 01 & 02 = No Major = 00 00  
Data 03 & 04 = No Minor = 00 00  
Data 05 = Analog Cable TV = 01  
Total = ma 00 23 00 00 00 00 01  
* This feature is varied based on the model.  
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]  
[Data 02][Data 03][Data 04][Data 05]  
[x][a][ ][Set ID][ ][NG][Data 00][x]  
21. Channel(Programme) Add/Del(Skip)  
(Command: m b)  
2. Tune to the digital antenna (ATSC) channel 30-3.  
Set ID = All = 00  
► To skip current channel(programme) for next time.  
Data 00 = Don’t know Physical = 00  
Data 01 & 02 = Major is 30 = 00 1E  
Data 03 & 04 = Minor is 3 = 00 03  
Data 05 = Digital Antenna TV = 22  
Total = ma 00 00 00 1E 00 03 22  
Transmission [m][b][ ][Set ID][ ][Data][Cr]  
Data 00 : Del(ATSC,ISDB)/Skip(DVB) 01 : Add  
Ack [b][ ][Set ID][ ][OK/NG][Data][x]  
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]  
[Data 02][Data 03][Data 04][Data 05]  
[x][a][ ][Set ID][ ][NG][Data 00][x]  
* Set the saved channel status to del(ATSC, ISDB)/  
skip(DVB) or add.  
• For Japan Model  
► To tune channel to following physical/major/minor  
22. Key (Command: m c)  
number.  
► To send IR remote key code.  
Transmission [m][c][ ][Set ID][ ][Data][Cr]  
Transmission [m][a][ ][0][ ][Data00][ ][Data01]  
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]  
Data Key code - p.2.  
* Digital Antenna/Satellite  
Data 00: xx (Don't care)  
Ack [c][ ][Set ID][ ][OK/NG][Data][x]  
[Data 01][Data 02]: Major Channel Number  
Data 01: High byte Channel Data  
Data 02: Low byte Channel Data  
23. Control Backlight (Command: m g)  
• For LCD TV / LED TV  
► To control the backlight.  
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)  
Transmission [m][g][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
[Data 03][Data 04]: Minor/Branch Channel Number  
(Don’t care in Satellite)  
Data 03: High byte Channel Data  
Data 04: Low byte Channel Data  
Ack [g][ ][Set ID][ ][OK/NG][Data][x]  
Control Panel Light (Command: m g)  
Data 05 : Input Source (Digital/Satellite for Japan)  
- 02 : Antenna TV (DTV)  
• For Plasma TV  
► To control the panel light.  
- 07 : BS (Broadcasting Satellite)  
- 08 : CS1 (Communication Satellite 1)  
- 09 : CS2 (Communication Satellite 2)  
Transmission [m][g][ ][Set ID][ ][Data][Cr]  
Data Min : 00 to Max : 64  
* Tune Command Examples:  
Ack [g][ ][Set ID][ ][OK/NG][Data][x]  
1
Tune to the digital antenna (ISDB-T) channel 17-1  
Set ID = All = 00  
.
Data 00 = Don’t know Physical = 00  
Data 01 & 02 = Major is 17 = 00 11  
Data 03 & 04 = Minor/Branch is 1 = 00 01  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXTERNAL CONTROL DEVICE SETUP  
11  
24. Input select (Command: x b)  
(Main Picture Input)  
00  
01  
02  
03  
O
X
X
X
O
X
X
O
O
X
X
O
► To select input source for main picture.  
Transmission [x][b][ ][Set ID][ ][Data][Cr]  
Data  
X : don’t care  
00 : DTV  
01 : CADTV  
10 : ATV  
02 : Satellite DTV  
ISDB-BS (Japan)  
03 : ISDB-CS1 (Japan)  
04 : ISDB-CS2 (Japan)  
11 : CATV  
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02]  
[Data03][x]  
[t][ ][Set ID][ ][NG][Data00][x]  
20 : AV or AV1  
21 : AV2  
26. Extended 3D(Command: x v) (only 3D models)  
(Depending on model)  
40 : Component1  
60 : RGB  
41 : Component2  
► To change 3D option for TV.  
Transmission [x][v][ ][Set ID][ ][Data 00][ ]  
[Data 01][Cr]  
90 : HDMI1  
92 : HDMI3  
91 : HDMI2  
93 : HDMI4  
Ack [b][ ][Set ID][ ][OK/NG][Data][x]  
[Data 00] 3D option  
* This function depends on model and signal.  
00 : 3D Picture Correction  
01 : 3D Depth (3D Mode is Manual Only)  
02 : 3D Viewpoint  
06 : 3D Color Correction  
07 : 3D Sound Zooming  
08 : Normal Image View  
09 : 3D Mode (Genre)  
25. 3D(Command: x t) (only 3D models)  
(Depending on model)  
► To change 3D mode for TV.  
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01]  
[Data 01] It has own range for each 3D option  
determined by [Data 00].  
1) When [Data 00] is 00  
00 : Right to Left  
[ ][Data 02][ ][Data 03][Cr]  
* (Depending on model)  
Data Structure  
[Data 00] 00 : 3D On  
01 : 3D Off  
01 : Left to Right  
02 : 3D to 2D  
03 : 2D to 3D  
2) When [Data 00] is 01, 02  
Data  
Min: 0 - Max: 14 (*transmit by Hexadecimal  
code)  
[Data 01] 00 : Top and Bottom  
01 : Side by Side  
Data value range(0 - 20) converts Viewpoint range  
(-10 - +10) automatically (Depending on model)  
* This option works when 3D Mode (Genre) is manual  
only.  
02 : Check Board  
03 : Frame Sequential  
04 : Column interleaving  
05 : Row interleaving  
[Data 02] 00 : Right to Left  
01 : Left to Right  
3) When [Data 00] is 06, 07  
00 : Off  
01 : On  
[Data 03] 3D Effect(3D Depth): Min : 00 - Max : 14  
(*transmit by Hexadecimal code)  
* [Data 02], [Data 03] functions depend on model  
and signal.  
4) When [Data 00] is 08  
00 : Revert to 3D video from 3D-to-2D  
converted 2D video  
01 : Change 3D video to 2D video, except  
2D-to-3D video  
* If [Data 00] is 00 (3D On), [Data 03] has no  
meaning.  
* If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data  
01], [Data 02] and [Data 03] have no meaning.  
* If conversion condition doesn’t meet, command is  
treated as NG.  
* If [Data 00] is 03 (2D to 3D), [Data 01] and  
[Data 02] have no meaning.  
5) When [Data 00] is 09  
* If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data  
03] works when 3D Mode (Genre) is manual only.  
00 : Standard  
02 : Cinema  
04 : Manual  
01 : Sport  
03 : Extreme  
05 : Auto  
* All 3D pattern options ([Data 01]) may not be  
available according to broadcasting/video signal.  
Ack [v][ ][Set ID][ ][OK][Data00][Data01][x]  
[v][ ][Set ID][ ][NG][Data00][x]  
[Data 00]  
[Data 01]  
[Data 02]  
[Data 03]  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXTERNAL CONTROL DEVICE SETUP  
12  
27. Auto Configure (Command: j u)  
(Depending on model)  
► To adjust picture position and minimize image  
shaking automatically. It works only in RGB (PC)  
mode.  
Transmission [j][u][ ][Set ID][ ][Data][Cr]  
Data 01 : To set  
Ack [u][ ][Set ID][ ][OK/NG][Data][x]  
Download from Www.Somanuals.com. All Manuals Search And Download.  
webOS TV Quick Setup Guide  
* Image shown may differ from your TV.  
* Image shown on a PC or mobile phone may vary depending upon the Operating System (OS).  
* Depending upon the version of the software, icon position can be changed.  
Network Settings  
Press the  
(Home) button to access the  
1
WI-FI NETWORK  
Picture  
Network /  
Smarthome menu. Select  
Wheel (OK).  
(Settings) and press  
Sound  
iptime_xu.ji  
iptime_shinsung.kang  
iptime_ungkee.choi  
Channels  
Network  
iptime_sungho.jo  
iptime_seungjun.lee  
Add a Hidden Wireless Network  
Connect via WPS PBC  
General  
Connect via WPS PIN  
Advanced Wi-Fi Settings  
Safety  
Accessibility  
For wireless AP (Router) that has the symbol, you need  
to enter the security key.  
(All Settings) and press Wheel (OK).  
Select  
2
3
If the connection is completed, Connected to  
Internet is displayed.  
5
NETWORK  
Picture  
Sound  
TV Name  
[LG] webOS TV  
Channels  
Wired Connection (Ethernet)  
Not Connected  
Network  
Wi-Fi Connection  
Connected to Internet  
Select the Network  
(Ethernet) or Wi-Fi Connection  
Wired Connection  
Wi-Fi Direct  
General  
LG Connect Apps  
.
Safety  
NETWORK  
Picture  
Accessibility  
Sound  
You can check the status of connection  
in Advanced Wi-Fi Settings.  
TV Name  
[LG] webOS TV  
Channels  
Wired Connection (Ethernet)  
Not Connected  
Network  
Wi-Fi Connection  
WI-FI NETWORK  
Picture  
Not Connected  
Network /  
Wi-Fi Direct  
General  
LG Connect Apps  
Sound  
iptime_xu.ji  
Safety  
iptime_shinsung.kang  
Channels  
iptime_ungkee.choi  
Accessibility  
iptime_sungho.jo  
Network  
iptime_seungjun.lee  
The device automatically tries to connect to the  
available network (wired network first).  
When you select the Wi-Fi Connection, the  
network list available is displayed. Choose the  
network you wish to use.  
4
Add  
a
Hidden Wireless Network  
General  
Connect via WPS PBC  
Connect via WPS PIN  
Advanced Wi-Fi Settings  
Safety  
Accessibility  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting Network Problems  
Depending upon the version of the software, icon position can be changed.  
Press the  
(Home) button to access the  
1
Check the AP (Router) or consult your Internet  
service provider.  
Smarthome menu. Select  
Wheel (OK).  
(Settings) and press  
When X appears next to Gateway:  
Unplug the power cord of the AP (Router) or cable  
modem, wait 10 seconds. Reapply power.  
1
(All Settings)  
Select  
and press Wheel (OK)  
2
3
.
Initialize (Reset) the AP (Router) or cable modem.  
2
3
Contact Internet service provider or AP  
(Router) manufacturer.  
When X appears next to DNS:  
Unplug the power cord of the cable modem or the  
AP (Router), wait 10 seconds. Reapply power.  
1
2
3
Select the Network  
Wired Connection  
(Ethernet) Wi-Fi Connection  
Advanced Wi-  
or  
After the cable modem or AP (Router) has  
initialized (Reset), try to reconnect.  
Fi Settings.  
NETWORK  
Picture  
Sound  
WI-FI NETWORK  
Picture  
Sound  
Check that the MAC address of the TV/AP (Router)  
is registered with your Internet service provider.  
(The MAC address displayed on the right pane of  
the network status window should be registered  
with your Internet service provider.)  
Network /  
iptime_xu.ji  
TV Name  
iptime_shinsung.kang  
iptime_ungkee.choi  
[LG] webOS TV  
Channels  
Network  
Channels  
Network  
Wired Connection (Ethernet)  
Not Connected  
iptime_sungho.jo  
Wi-Fi Connection  
Not Connected  
iptime_seungjun.lee  
Wi-Fi Direct  
General  
General  
Add  
a
Hidden Wireless Network  
LG Connect Apps  
Check the AP (Router) manufacturer’s website  
to make sure your router has the latest firmware  
version installed.  
4
Connect via WPS PBC  
Connect via WPS PIN  
Advanced Wi-Fi Settings  
Safety  
Safety  
Accessibility  
Accessibility  
Follow the instructions below that match to your  
network status.  
Check the TV or the AP (Router).  
When X appears next to TV:  
Check the connection status of the TV,  
AP (Router) and cable modem.  
1
2
Power off and power on in the following order; (1st)  
the cable modem, wait for the cable modem to reset,  
(2nd) the AP (Router), wait for the AP (Router) to  
reset and (3rd) the TV.  
If you are using a static IP, enter the IP directly.  
3
4
Contact Internet service provider or AP (Router)  
manufacturer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SmartShare PC SW Installation & Setting  
Install the SmartShare PC SW program on your PC.  
Go towww.lg.com. Then, select your region.  
1
2
3
4
Select SUPPORT.  
Select Software & Firmware. Then, search for your model. Then, select SmartShare PC SW.  
Download the SmartShare PC SW and install it on your PC. You can run the program when installation is  
complete.  
NOTE  
SmartShare service is only available if TV and other devices are connected to the same AP (Router).  
y
SmartShare Connection to Smartphone  
Check that Wi-Fi is enabled on your smartphone. To use SmartShare, both devices must on the  
same local network.  
1
Install/run the app for sharing content on your smartphone (It's called LG TV Plus on LG phones).  
2
3
Enable your smartphone to share content files with other devices.  
Open Device Connector application on TV.  
SHARE.  
(Home)  
Device Connector  
Smartphone  
CONTENT  
4
Select the file type you want to play (movie, audio, or photo).  
Select a movie, music, or photo file to play on the TV.  
Play the media file to view and enjoy it on your TV.  
5
6
7
Updating the TV Firmware  
(Home)  
(Settings)  
(All Settings)  
General  
About This TV  
CHECK FOR UPDATES  
You can check the Software Version and update it.  
If you check the Allow Automatic Updates, the TV will check for updated software automatically each time the set  
is turned on (Internet Connection is required).  
* When the TV is turned on for the first time after a software update, initialization of the TV may take approximately  
one minute.  
GENERAL  
ABOUT THIS TV  
Picture  
Sound  
Picture  
Sound  
General /  
Language  
Software Version  
xx.xx.xx  
Location  
Channels  
Network  
Channels  
Network  
Time & Date  
Timers  
CHECK FOR UPDATES  
Allow Automatic Updates  
Standby Light  
Home/Store Mode  
Power saving mode  
SIMPLINK  
TV Information  
LG webOS TV  
General  
General  
LG Remote Service  
Customer Service  
x-xxx-xxx-xxxx  
Settings Help  
Reset to Initial Settings  
About This TV  
Safety  
Safety  
User Agreements  
Legal Notice  
Accessibility  
Accessibility  
Open Source Software Notice  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wi-Fi Direct Setting  
(Home)  
(Settings)  
(All Settings)  
Network  
Wi-Fi DIRECT  
If a local network is not available, you can connect a portable device directly to the TV using Wi-Fi Direct.  
With SmartShare, you can share files or screens of devices connected to Wi-Fi Direct.  
WI-FI DIRECT  
Picture  
Network  
/
When you open Wi-Fi Direct menu, a list of available devices appears. Select your  
device.  
REFRESH LIST  
1
2
Sound  
Channels  
Network  
LG Smart+ TV  
When you are prompted to the connection request, select Yes. Wi-Fi Direct is  
now connected to your TV.  
General  
* You can only use devices that support WiFi Direct.  
Safety  
Accessibility  
Miracast Setting  
Miracast allows a portable device to send video and sound securely to the TV wirelessly.  
(Home) / (Input) (Screen Share)  
Miracast should be set to ON on your portable device.  
1
2
When your TV is detected, select the device on your portable device.  
When connection is completed, the device screen appears on the TV screen.  
* If you turn Listen Mode to ON after launching the Screen Share app, you can connect the device without starting  
the Screen Share app.  
WiDi (Wireless Display) Setting  
Intel® WiDi (Wireless Display) technology enables easy and fast connection without wires or internet network for  
mirrored and dual monitor display on your TV. You can sit back and experience your favorite movies, videos, photos,  
online shows and more in full HD on your TV with great image clarity and sound.  
(Home) /  
(Input)  
(Screen Share)  
On the TV Intel® WiDi is set to On. Your laptop runs the Intel® WiDi program.  
* LG TVs do not need to register.  
* For more information on Intel® WiDi, visithttp://intel.com/go/widi .  
* You can control your PC using the Magic Remote. (above WiDi version 4.2)  
1
2
It detects LG webOS TVs available, which supports WiDi. In the list, select the TV you want and click Connect.  
Enter the number shown on the screen into the input field ( ) on your laptop and then click Continue.  
Notebook Screen  
The laptop screen appears on the TV screen. The wireless environment may affect the screen display. If the  
connection is poor, the Intel® WiDi connection may be lost.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting Wi-Fi Network Problems  
Checkpoints  
Make sure that you have the latest version of the software.  
y
If you are using a Wi-Fi router, check whether you have the latest firmware installed.  
If there are any available updates, update the firmware according to the manufacturer's instructions.  
Check the current software version and if there is an available update, install it.  
-
-
-
(Home)  
(Settings)  
(All Settings)  
General  
About This TV  
Software Version  
Check if the same symptom occurs with two or more Wi-Fi devices.  
y
y
Wi-Fi problems may be related to network condition and a device that is connected to the network.  
If other Wi-Fi devices can connect to the Internet at the same location as the TV, then your Wi-Fi router is  
probably normal.  
-
-
Check the power and Ethernet cables of the Wi-Fi router.  
When the Ethernet cable connected to the Wi-Fi router is loose or disconnected, network problems can  
-
occur.  
Check all power and Ethernet cables of the Wi-Fi router to see if they are correctly connected.  
-
Check the Wi-Fi router to see if the router is set to the recommended wireless settings. If network problems  
continue, reset your network devices.  
Check the signal strength of the Wi-Fi router to connect to from the TV UI.  
y
y
The  
that is next to the Wi-Fi router name (SSID) in the menu indicates the sensitivity of the receiver.  
-
-
-
It is recommended that you connect to a Wi-Fi network with 3 or more bars of signal strength.  
If the number of bars indicating signal strength are less than 3, the network connection status may be weak  
or unstable, so shorten the distance between the Wi-Fi router and the TV.  
If the signal strength of the Wi-Fi router is weak, wireless speed slowdowns and network disconnection may  
occur.  
To supplement wireless coverage of network equipment, your Wi-Fi router should be placed in the middle of  
the network equipment.  
y
y
Wi-Fi Router  
Interference Factors  
y
y
If there is any interference from surrounding equipment, the network connection may be weak or unstable.  
Wireless telephones that operate in the 2.4 GHz or 5 GHz bandwidth  
Wireless speakers that operate in the 2.4 GHz or 5 GHz bandwidth  
Video transmitters that operate in the 2.4 GHz or 5 GHz bandwidth  
Other wireless devices (Microwaves, cameras, baby monitors, neighboring wireless devices, etc.) that operate  
in the 2.4 GHz or 5 GHz bandwidth.  
-
-
-
-
How to reduce the effects of interference between Wi-Fi and Bluetooth devices  
Set the channel on your wireless network equipment to avoid the 2.4 GHz or 5 GHz bandwidth which has lots  
of interference.  
-
If possible, use the 5 GHz wireless network.  
If the Wi-Fi router is located too far away or in environments with high interference, the network connection  
may be weak or unstable.  
-
-
In this case, move the Wi-Fi router closer to the TV or check if there are any obstructions (e.g., concrete walls,  
cabinets) between the two devices.  
-
Download from Www.Somanuals.com. All Manuals Search And Download.  
Radio Frequency (RF) Interference and Absorbing Obstructions  
y
Interference  
Potential  
Interference  
Interference  
Potential  
Type of Barrier  
Wood  
Synthetic material  
Glass  
Type of Barrier  
Type of Barrier  
Potential  
Medium  
Medium  
Medium  
Plaster  
Concrete  
High  
High  
High  
Low  
Low  
Low  
Water  
Bricks  
Marble  
Bulletproof glass  
Metal  
Very High  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ENGLISH  
Easy Setup Guide  
OLED TV  
OLED55E6P  
OLED65E6P  
Please read this manual carefully before operating your set and retain it for future reference.  
ESPAÑOL  
Guía Rápida de Configuración  
Lea atentamente este manual antes de poner en marcha el equipo y consérvelo para futuras consultas.  
FRANÇAIS  
Guide de configuration rapide  
Avant d’utiliser l’appareil, veuillez lire attentivement ce guide et conservez-le pour pouvoir vous y reporter ultérieurement.  
AA  
X 4  
(M4 x L20)  
www.lg.com  
P/No: MFL69383608 (1602-REV00)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ENGLISH Read Safety and Reference.  
ESPAÑOL Leer Seguridad y Consultas.  
FRANÇAIS Lisez Sécurité et références.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
2
4
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
1
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
ENGLISH  
OLED55E6P  
(OLED55E6P-U)  
OLED65E6P  
(OLED65E6P-U)  
2
0
1
MODELS  
1,237 x 767 x 175 (mm)  
48.7 x 30.1 x 6.8 (inches)  
1,237 x 767 x 56.7 (mm)  
48.7 x 30.1 x 2.2 (inches)  
18.5 kg (40.7 lbs)  
1,461 x 893 x 200 (mm)  
57.5 x 35.1 x 7.8 (inches)  
1,461 x 893 x 56.7 (mm)  
57.5 x 35.1 x 2.2 (inches)  
24.8 kg (54.6 lbs)  
With stand  
Dimensions  
(W x H x D)  
Without stand  
With stand  
Weight  
Without stand  
For USA and Canada  
For Mexico  
17.1 kg (37.6 lbs)  
22.8 kg (50.2 lbs)  
2.3 A / 230 W  
3.3 A / 330 W  
3.1 A / 310 W  
4.3 A / 430 W  
Current value / Power consumption  
Power requirement  
AC 120 V ~ 50 / 60 Hz  
ESPAÑOL  
FRANÇAIS  
MODELOS  
MODÈLES  
OLED55E6P  
(OLED55E6P-U)  
OLED65E6P  
(OLED65E6P-U)  
Con base  
1 237 x 767 x 175 (mm)  
1 461 x 893 x 200 (mm)  
Dimensiones  
(Ancho x altura x profundidad)  
Avec support  
48,7 x 30,1 x 6,8 (pulgadas / po) 57,5 x 35,1 x 7,8 (pulgadas / po)  
1 237 x 767 x 56,7 (mm) 1 461 x 893 x 56,7 (mm)  
48,7 x 30,1 x 2,2 (pulgadas / po) 57,5 x 35,1 x 2,2 (pulgadas / po)  
Sin base  
Dimensions  
(L x H x P)  
Sans support  
Con base  
Peso  
18,5 kg (40,7 libras / lb)  
17,1 kg (37,6 libras / lb)  
24,8 kg (54,6 libras / lb)  
22,8 kg (50,2 libras / lb)  
Avec support  
Sin base  
Poids  
Sans support  
Para Estados Unidos y Canadá  
Para México  
Pour les États-Unis et le Canada  
Pour le Mexique  
2,3 A / 230 W  
3,3 A / 330 W  
2,3 A / 230 W  
3,3 A / 330 W  
3,1 A / 310 W  
4,3 A / 430 W  
3,1 A / 310 W  
4,3 A / 430 W  
Corriente de consumo / Consumo de potencia  
Valeur courante / Consommation électrique  
Alimentación requerida  
Alimentation  
AC 120 V ~ 50 / 60 Hz  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

KTI Networks Network Card KG 502T User Manual
Land Pride Brush Cutter RCR1860 User Manual
Lincoln Electric Welder 455 M User Manual
Lincoln Welder ML 2 User Manual
LST Smoke Alarm FC600 TDIFF 57 User Manual
Magic Chef Coffeemaker EWCM11TS12 User Manual
Makita Impact Driver BTW074 User Manual
McCulloch Lawn Mower M65B53SD User Manual
McIntosh Stereo Amplifier MA6600 User Manual
Melissa Coffeemaker 745 183 User Manual