INSTALLATION MANUAL
ELECTRIC DOUBLE OVEN RANGE
Please read these instructions thoroughly before
installing and operating the range.
LDE3019ST
LDE3017ST
LDE3017SB
LDE3017SW
LDE3015ST
LDE3015SB
LDE3015SW
P/No.: MFL63290401
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 1
SAFETY
WARNING
• The middle (neutral or ground) wire of a 3 wire power cord or a 3 wire conduit has to be
connected to the middle post of the main terminal block. The remaining two wires of the
power cord or conduit have to be connected to the outside posts of the main terminal
connection block.
- Failure to do so can result in electrical shock, severe personal injury or death.
•
Only a 4-conductor power-supply cord kit rated 120/240 volts, 50 amperes and marked for use
with ranges with closed-loop connectors or open-end spade lugs with upturned ends shall be
used. The middle (neutral) wire of the power cord or 4-wire conduit has to be connected to the
middle post of the main terminal block. The other two wires of the power cord or conduit have
to be connected to the outside posts of the main terminal connection block. The 4th ground
wire must be connected to the frame of the range with the ground screw.
- Failure to do so can result in electrical shock, severe personal injury or death.
CAUTION
• You should put on gloves during the installation procedure.
- Failure to do so can result in bodily injury.
• You should make sure that the wall covering, countertop and cabinets around the range
can withstand the heat (up to 194°F) generated by the range.
- Discoloration, delamination or melting may occur.
- This range has been designed to comply with the maximum allowable wood cabinet temperatures of 194°F.
• Cabinet storage space located above the surface units should be avoided.
• You should install a range hood that projects horizontally a minimum of 5 inches
beyond the bottom of the cabinets. If cabinet Storage is to be provided.
- The risk of burns or fire by reaching over the heated surface elements can be reduced.
• You should not install the range in the humid place. Splashing the range with water or
any electrolyte can result in electrical shock.
• You should not let cooking grease or flammable material accumulate in or near the
range.
- Failure to do so can result in serious burns.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 1
SAFETY
PREPARE TO INSTALL THE RANGE
WARNING
• The information in this manual
TOOLS NEEDED
should be followed exactly.
- A fire or electrical shock may result causing
property damage, personal injury or death.
WARNING
• Any person should not
step or sit on the oven
door. You should install the
Anti-Tip Bracket supplied
with the range.
- The range could be tipped and
injury might result from spilled hot
liquid, food, or the range itself.
Safety Glasses
Tape Measure
- If the range is pulled away from
the wall for cleaning, service, or
any other reason, ensure that the
Anti-Tip Device is properly
Gloves
Pencil
reengaged when the range is
pushed back against the wall.
PARTS PROVIDED
CAUTION
• You should put on gloves during
the installation procedure.
- Failure to do so can result in bodily injury.
NOTE
• Read all instructions contained in these installation
instructions before installing range.
• Remove all packing materials from the oven
compartments before connecting the electrical
supply to the range.
(For Anti-Tip Bracket Mounted
on Concrete Floors and Walls)
PARTS NOT PROVIDED
• Observe all governing codes and ordinances.
•
Be sure to leave these instructions with the consumer.
NOTE
Keep these instructions with your owner’s manual for
future reference.
• As when using any appliance generating heat, there
are certain safety precautions you should follow.
• Be sure your range is installed and grounded
properly by a qualified installer or service technician.
• Make sure the wall coverings around the range can
withstand the heat generated by the range.
• To eliminate the need to reach over the surface
elements, cabinet storage space above the elements
should be avoided.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 2
PREPARE TO INSTALL THE RANGE
INSTALLATION DRAWINGS (LDE Series only)
2
WARNING
You should use two or more people to move
(Excessive Weight Hazard)
and install range.
- Failure to do so can result in back or other injury.
NOTE
•
SAVE FOR THE USE OF THE LOCAL
ELECTRICAL INSPECTOR.
CLEARANCES AND DIMENSIONS (Figure 1)
To install range refer to the following Figure 1.
For installation in CANADA, a Free-standing range
is not to be installed closer than 15/32 (12mm) from
any adjacent surface.
•
You never pull or push any handles of upper
& lower door to move and install range.
- Failure to do so can result in serious damage to
the door of the range.
CAUTION
CAUTION
•
You should make sure that the wall
covering, countertop and cabinets
around the range can withstand the heat
(up to 194°F) generated by the range.
Discoloration, delamination or melting may occur.
• Cabinet storage space located above
the surface units should be avoided.
•
You should install a range hood that
projects horizontally a minimum of 5
inches beyond the bottom of the cabinets.
If cabinet Storage is to be provided.
-
- This range has been designed to comply with
the maximum allowable wood cabinet
temperatures of 194°F.
- The risk of burns or fire by reaching over the
heated surface elements can be reduced.
Cabinet
opening
Wall
Center
15”(38cm)
11”(28cm)
Cabinet
6”
2.5”(6.3cm)
(15.2cm)
5”
4”
9”
6”
(13cm)
(10cm)
(23cm)
(15.2cm)
2.5”
4”
9”
(23cm)
(6.3cm)
(10cm)
A = 30”(76.2 cm) For U.S.A
= 30”(76.2 cm) ~ 31”(78.7 cm) For CANADA
FIGURE 1
FIGURE 2
MINIMUM DIMENSIONS (Figure 2)
* 30”(76.2 cm) minimum clearance between the top of the cooking surface and the bottom of an
unprotected wood or metal cabinet; or 24”(60.9 cm) minimum when bottom of wood or metal cabinet is
protected by not less than 1/4”(6.4 cm) flame retardant millboard covered with not less than no. 28 MSG
sheet steel, 0.015”(0.381 mm) stainless steel, 0.024”(0.610 mm) aluminum or 0.020”(0.508 mm) copper.
** 15”(38.1 cm) minimum between countertop and adjacent cabinet bottom.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 3
ELECTRICAL CONNECTIONS
3 ELECTRICAL CONNECTION
REQUIREMENTS
4
CONNECT RANGE CORD
WARNING
You never remove the protection cover
This appliance must be installed and grounded on a branch
circuit by a qualified technician in accordance with the
National Electrical code ANSI/NFPA NO. 70 - latest edition.
•
covering the rear of lower oven.
Failure to do so can result in serious damage to power cord.
The damage causes serious burns and electric shock.
A
ll wiring should conform to Local and NEC. This range
-
requires a single-phase, 3 wire, A.C 120/208V or 120/240V 60Hz
electrical system. Use only a 3-conductor or a 4-conductor
UL-listed range cord with closed-loop terminals, open-end
spade lugs with upturned ends or similar termination. DO
NOT install the power cord without a strain relief.
The Rear Access cover must be removed. Loosen the
three screws with a screwdriver. The terminal block
will then be accessible.
A range cord rated at 40 amps with 120/240 minimum volt
range is required. If a 50 amp range cord is used, it should
be marked for use with 13⁄8” diameter connection openings.
This appliance may be connected by means of conduit or
power cord. If conduit is being used, go to page 7 for 3 wire
conduit connections or page 8 for 4 wire conduit connections.
Protection cover
WARNING
• New branch-circuit installations (1996 NEC)
for mobile homes, recreational vehicles, and
installations where local codes do not allow
grounding through the neutral wire require a
4-conductor UL listed range cord or 4 wire
conduit connection.
FIGURE 4
The Cord/Conduit connection plate is used for the
installation of power cord or conduit. For power cord,
install it with the connection plate as INSTALLED. For
conduit, remove the connection plate located below the
rear of the drawer body and use the conduit hole (11/8”)
instead of power cord hole (13/8”). (Refer to Figure 5 and 6.)
•
•
•
Power supply cord and plug should not be
modified. If it will not fit the outlet, have a proper
outlet Installed by a qualified electrician.
Using an extension cord to connect the power is
prohibited. The way to connect the power cord
and plug directly is strongly recommended.
Electrical ground is required on this appliance.
• You should make sure that the power cord is
not pinched by the range or heavy objects.
Remove the Conduit connection plate
FIGURE 5
-
Failure to do so can result in serious burns or electrical shock.
Specified power-supply-cord kit rating
Diameter (inches) of Range
Range rating, watts
Specified rating
of power-supply-
cord kit, amperes
connection Opening
120/240 volts 120/208 volts
Power cord
Conduit
3-wire 3-wire
8,750 - 16,500 7,801 - 12,500
16,501 - 22,500 12,501 - 18,500
40 or 50A
13/8”
11/8”
13/8”
50
13/4”
Assemble the
strain relief hole
3, 4 - Wire electrical wall Receptacle
4 Wire receptacle (14-50R)
3 Wire receptacle (10-50R)
Reinstall the Cord/Conduit connection plate
FIGURE 3
FIGURE 6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 3
ELECTRICAL CONNECTIONS
3-wire connection with a power supply cord
WARNING
• The middle (neutral or ground) wire of a 3
wire power cord or a 3 wire conduit has to
be connected to the middle post of the
main terminal block. The remaining two
wires of the power cord or conduit have to
be connected to the outside posts of the
main terminal connection block.
- Failure to do so can result in electrical shock, severe
personal injury or death.
Separate Strain Relief
before installation
Install the power cord as follows:
Assemble the strain relief
to the 13/8” opening in
Conduit connection plate
For power cord installations, Hook the strain relief
over the power cord hole (13/8”) located below the rear
of lower oven. Insert the power cord through the
strain relief and tighten it. (Refer to Figure 7.)
FIGURE 7
DO NOT install the power cord without a strain relief.
1. Remove the lower 3 screws from the terminal block
and retain them. (Refer to Figure 8.)
2. Insert the 3 screws through each power cord
terminal ring and into the lower terminals of the
terminal block.
3-wire connection
Make sure that the center wire (white/neutral) is
connected to the center lower position of the
terminal block.
3. Tighten 3 screws securely into the terminal block.
Do not remove the ground strap connections.
4. Go to page 10.
FIGURE 8
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 3
ELECTRICAL CONNECTIONS
4-wire connection with a power supply cord
3-wire connection: conduit
Install the conduit as follows:
Remove the Conduit connection plate from the rear of
lower oven and rotate it as shown in Figure 5. The
conduit hole (11/8”) must be used.
WARNING
• Only a 4-conductor power-supply cord kit
rated 120/240 volts, 50 amperes and
marked for use with ranges with closed-
loop connectors or open-end spade lugs
with upturned ends shall be used. The
middle (neutral) wire of the power cord or
4-wire conduit has to be connected to the
middle post of the main terminal block.
The other two wires of the power cord or
conduit have to be connected to the
outside posts of the main terminal
connection block. The 4th ground wire
must be connected to the frame of the
range with the ground screw.
First, prepare the conduit wires as shown in Figure 10.
3 wire
4 wire
or
FIGURE 10
Second, install conduit as shown in Figure 6.
- Failure to do so can result in electrical shock, severe
personal injury or death.
For conduit installations, after purchasing a strain
relief, insert it in the conduit hole (11/8”). Then install
the conduit through the body of strain relief and
fasten the strain relief with its ring. Reinstall the
bracket.
Follow the instructions under “ 4 CONNECT RANGE
CORD” on page 5 to correctly install the strain relief.
1. Remove the lower 3 screws from the terminal block
and retain them. (Refer to Figure 9.)
For conduit connections :
If the wire in the conduit is copper it must be 8 or 10
AWG wiring.
If the wire in the conduit is aluminum it must be 6 or 8
AWG wiring.
Remove the ground screw and retain it.
2. Remove ground strap and discard as shown
in Figure 9.
Do not discard any screws.
3. Insert the ground screw into the power cord ground
1. Loosen the lower 3 screws from the terminal block.
wire terminal ring and secure it to the range frame.
(Refer to Figure 11.)
4. Insert the 3 screws through each power cord
terminal ring and into the lower terminals of the
terminal block. Make sure that the center wire
(white/neutral) is connected to the center lower
position of the terminal block.
2. Insert the bare wire (white/neutral) end through the
center terminal block opening.
Do not remove ground strap connections.
3. Insert the two side bare wire ends into the lower left
and the lower right terminal block opening.
Tighten the 3 screws securely into the terminal block.
(approximately 35 - 50 IN-LB)
Tighten 3 screws securely into the terminal block.
5. Go to page 10.
4. Go to page 10.
4-wire connection
3-wire connection
FIGURE 11
FIGURE 9
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 3
ELECTRICAL CONNECTIONS
4-wire connection: conduit
1. Follow the instructions under “Install the conduit as
follows” on page 7 to correctly install the strain
relief.
4-wire connection
DO NOT install the conduit without a strain relief.
2. Loosen the 2 lower left and right screws from the
terminal block. (Refer to Figure 12.)
Remove the lower 2 center screws.
3. Remove ground strap and discard as shown
in Figure 12.
Do not discard any screws.
4. Attach the ground bare wire end to range frame
and secure it in place with the ground screw (Refer
to figure 12.)
5. Insert the bare wire (white/neutral) end through the
center terminal block opening.
6. Insert the two side bare wire ends into the left and
the right terminal block opening.
Tighten the 3 screws securely into the terminal
block. (approximately 35 - 50 IN-LB)
7. Go to page 10.
FIGURE 12
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 4
INSTALL THE RANGE
Replace the access cover on the back of the range. To
replace the wire cover, insert the two tabs into the
openings located below the opening and tighten the
three screws.
Use a level to check your adjustments. Place the level
diagonally on the oven rack, and check each direction
for level.
5 ANTI-TIP DEVICE INSTALLATION
First check direction 1 .
WARNING
After check direction 2 .
• Any person should not
step or sit on oven door.
You should install the Anti-
Tip Bracket supplied with
If the level doesn’t show
level on the rack, adjust the
leveling legs with a wrench.
the range.
6 FINAL INSTALLATION
- The range could be tipped and
injury might result from spilled hot
liquid, food, or the range itself.
• Move range close enough to the opening to plug
into the receptacle.
• Slide range into position insuring that the left back
leg slides under the anti-tip bracket. Range should sit
flush against the back wall when properly installed.
- If the range is pulled away from
the wall for cleaning, service, or
any other reason, ensure that the
Anti-Tip Device is properly
reengaged when the range is
pushed back against the wall.
• Carefully attempt to tip range forward to insure that
the anti-tip bracket is engaged properly. If properly
installed, the anti-bracket will prevent the range from
being tipped. If the range can be tipped, reinstall the
range until the bracket is properly installed and the
range will not tip forward.
• Turn on electrical power. Check the range for proper
operation as described in owner’s manual.
1. Locate the bracket using the template
An Anti-tip bracket is packaged with template. The
instructions include necessary information to
complete the installation.
Read and follow range installation instruction sheet
(template).
2. Level the range
Level the range by adjusting the leveling legs with a
wrench.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
LG Customer Information Center
1-800-243-0000 USA, Consumer User
1-888-865-3026 USA, Commercial User
1-888-542-2623 CANADA
Register your product Online!
Printed in Mexico
Download from Www.Somanuals.com. All Manuals Search And Download.
|