V9810MZ.NA1ULZ_RV0016P_ENG
Installation and Operating Guide | Warranty
Model Number | ZDX-313 | DVD Player + Video Cassette Recorder
Fo r se rvic e /
sup p o rt Ca ll:
To ll Fre e Num b e r
1-800-243-0000
© Copyright 2005, LG Electronics U.S.A., Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND
THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
CAUTION:
This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or
fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installa-
tion, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVIC-
ING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and operating
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience recepta-
cles, and the point where they exit from the product.
instructions should be read before the product is operated.
2. Keep these instructions. - The safety, operating and use
instructions should be retained for future reference.
11. Only use attachments/accessories specified by the
manufacturer.
3. Heed all warnings. - All warnings on the product and in
the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use instruc-
tions should be followed.
5. Do not use this product near water. – For example: near
a bath tub, wash bowl, kitchen sink, laundry tub, in a wet
basement; or near a swimming pool; and other areas
located near water.
6. Clean only with dry cloth. – Unplug this product from the
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with appara-
tus. When a cart is used, use caution when moving
the cart/product combination to avoid injury from
tip-over.
wall outlet before cleaning. Do not use liquid cleaners.
7. Do not block any ventilation openings. Install in accor-
dance with the manufacturer’s instructions. - Slots and
openings in the cabinet are provided for ventilation and to
ensure reliable operation of the product and to protect it
from over- heating. The openings should never be blocked
by placing the product on a bed, sofa, rug or other similar
surface. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ven-
tilation is provided or the manufacturer’s instructions have
been adhered to.
13. Unplug this product during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the product has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the product, the product has been
exposed to rain or moisture, does not operate nor-
mally, or has been dropped.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
VCR Tape Recording . . . . . . . . . . . . . . . .22-25
Basic Instructions . . . . . . . . . . . . . . . . . . . . .22
Timer Recording . . . . . . . . . . . . . . . . . . .22-23
Instant Timer Recording . . . . . . . . . . . . . . .24
Recording from External Components . . . . .24
Copying from DVD to VCR . . . . . . . . . . . . .25
On-Screen Display - VCR . . . . . . . . . . . . . . .25
Additional VCR Information . . . . . . . . . . . . .26
VHS Auto Play System . . . . . . . . . . . . . . . . .26
S-VHS Quasi Playback (SQPB) . . . . . . . . . .26
Easy Information . . . . . . . . . . . . . . . . . . . . .26
Playing a DVD . . . . . . . . . . . . . . . . . . . . . .27-29
Playback Setup . . . . . . . . . . . . . . . . . . . . . .27
General Features . . . . . . . . . . . . . . . . . .27-29
• Moving to another TITLE . . . . . . . . . . . . .27
• Moving to another CHAPTER . . . . . . . . .27
• Slow motion . . . . . . . . . . . . . . . . . . . . . . .27
• Still Picture and Frame-by-Frame
Playback . . . . . . . . . . . . . . . . . . . . . . . . .28
• Search . . . . . . . . . . . . . . . . . . . . . . . . . . .28
• Time Search . . . . . . . . . . . . . . . . . . . . . .28
• Marker Search . . . . . . . . . . . . . . . . . . . . .28
• Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . .28
• Repeat A-B . . . . . . . . . . . . . . . . . . . . . . .28
• Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
• Last Scene Memory . . . . . . . . . . . . . . . . .29
• Screen Saver . . . . . . . . . . . . . . . . . . . . . .29
Special DVD Features . . . . . . . . . . . . . . . .29
• Checking the contents of DVD discs:
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . .5
Moisture Condensation . . . . . . . . . . . . . . . . . .5
Symbols Used in this Manual . . . . . . . . . . . .5
About the
Symbol Display . . . . . . . . . . . . .5
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . .5
Types of Playable Discs . . . . . . . . . . . . . . . . .6
Disc-related terms . . . . . . . . . . . . . . . . . . . . .6
Regional Code . . . . . . . . . . . . . . . . . . . . . . . . .7
Notes on Regional Codes . . . . . . . . . . . . . . . .7
Notes on Copyrights . . . . . . . . . . . . . . . . . . . .7
Notice for Progressive Scan Use . . . . . . . . . .7
About the Remote Control . . . . . . . . . . . . . . .7
Selecting the Viewing Source . . . . . . . . . . . . .7
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Remote Control . . . . . . . . . . . . . . . . . . . . . . . .9
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Preparation . . . . . . . . . . . . . . . . . . . . . .10
Connecting an Antenna or Cable TV . . . . . . .11
Basic TV Connections . . . . . . . . . . . . . . .11-12
Optional TV Connections . . . . . . . . . . . . . . .12
Audio Connection for DVD . . . . . . . . . . . .12-13
Initial Settings - VCR . . . . . . . . . . . . . . . .14-15
General Operation . . . . . . . . . . . . . . . . . . . .14
CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
• Auto Clock Set . . . . . . . . . . . . . . . . . . . . .14
• Manual Clock Set . . . . . . . . . . . . . . . . . . .14
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . .14
TUNING . . . . . . . . . . . . . . . . . . . . . . . . . . .15
• Auto Channel Programming . . . . . . . . . .15
• To Add or Erase Channels . . . . . . . . . . . .15
SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
• FUNCTION OSD . . . . . . . . . . . . . . . . . .15
• AUDIO MODE . . . . . . . . . . . . . . . . . . . . .15
• BROADCAST TYPE
Menus . . . . . . . . . . . . . . . . . . . . . . . . . . .29
• Title Menu . . . . . . . . . . . . . . . . . . . . . . .29
• Disc Menu . . . . . . . . . . . . . . . . . . . . . . .29
• Camera Angle . . . . . . . . . . . . . . . . . . . .29
• Changing the Audio Language . . . . . . . . .29
• Subtitles . . . . . . . . . . . . . . . . . . . . . . . .29
On-Screen Display - DVD . . . . . . . . . . . . . . .30
Maintenance and Service . . . . . . . . . . . . . . .30
Playing an Audio CD or MP3/WMA Disc .31-32
Audio CD and MP3 / WMA Disc Features . .32
• Pause . . . . . . . . . . . . . . . . . . . . . . . . . .32
(STEREO / SAP / MONO) . . . . . . . . . . . .15
• AUDIO OUTPUT
• Moving to another Track
. . . . . . . . . . . .32
• Repeat Track / All / Off . . . . . . . . . . . . . . .32
• Search . . . . . . . . . . . . . . . . . . . . . . . . . . .32
• Random . . . . . . . . . . . . . . . . . . . . . . . . . .32
• Repeat A-B . . . . . . . . . . . . . . . . . . . . . . .32
Programmed Playback . . . . . . . . . . . . . . . .33
Viewing a JPEG Disc . . . . . . . . . . . . . . . . . .34
Slide Show . . . . . . . . . . . . . . . . . . . . . . . . .34
Still Picture . . . . . . . . . . . . . . . . . . . . . . . . . .34
Moving to another File . . . . . . . . . . . . . . . . .34
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
To rotate picture . . . . . . . . . . . . . . . . . . . . . .34
(STEREO / LEFT / RIGHT) . . . . . . . . . . .15
Initial Settings - DVD . . . . . . . . . . . . . . . .16-19
General Operation . . . . . . . . . . . . . . . . . . . .16
LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . .16
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . .17
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . .18
LOCK (Parental Control) . . . . . . . . . . . . . . .19
Operation . . . . . . . . . . . . . . . . . . . . . . .20
VCR Tape Playback . . . . . . . . . . . . . . . . .20-21
Basic Instructions . . . . . . . . . . . . . . . . . . . . .20
Auto Tracking . . . . . . . . . . . . . . . . . . . . . . . .20
Manual Tracking . . . . . . . . . . . . . . . . . . . . . .20
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Still Picture and Frame-by-Frame Playback .20
Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . .21
CM SKIP (Commercial Skip) . . . . . . . . . . . . .21
VHS Hi-Fi Stereo / MTS Broadcast . . . . . . . .21
Hi-Fi Stereo Audio Sound . . . . . . . . . . . . . . .21
MTS (Multi-Channel TV Sound) . . . . . . . . . .21
Reference . . . . . . . . . . . . . . . . . . . . . . .35
Controlling Your TV with the Supplied
Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Language Codes . . . . . . . . . . . . . . . . . . . . . .36
Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . .36
Troubleshooting . . . . . . . . . . . . . . . . . . .37-38
Specifications . . . . . . . . . . . . . . . . . . . . . . . .39
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
To ensure proper use of this product, please read this
owner’s manual carefully and retain for future refer-
ence.
About the
Symbol Display
“
” may appear on your TV display during opera-
tion and indicates that the function is not permitted by
this unit or the disc or not available at that time.
This manual provides information on the operation
and maintenance of your DVD+VCR. Should the unit
require service, contact an Authorized Service Center.
Notes on Discs
Handling Discs
Moisture Condensation
Do not touch the playback side of the disc. Hold the
disc by the edges so that fingerprints do not get on
the surface. Never stick paper or tape on the disc.
Never operate the DVD+VCR immediately after mov-
ing it from a cold location to a warm location. Leave it
unplugged for two or three hours without operating it.
If you use the DVD+VCR in such a situation, it may
damage discs/tapes and internal parts.
Symbols Used in this Manual
Indicates hazards likely to cause harm to
the unit itself or other material damage.
Storing Discs
After playing, store the disc in its case. Do not expose
the disc to direct sunlight or sources of heat and never
leave it in a parked car exposed to direct sunlight.
Not e:
Tip :
Indicates special notes and operating
features.
Cleaning Discs
Indicates tips and hints for making the task
easier.
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center out.
A section whose title has one of the following sym-
bols is applicable only to the disc represented by the
symbol.
DVD
CD
DVD
Audio CDs
MP3 Discs
WMA Discs
JPEG Discs
MP3
WMA
JPEG
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Types of Playable Discs
Disc-related terms
MP3
DVD
MP3 is a popular compression format used for digital
audio files that yields very high near-CD quality sound.
(8 cm / 12 cm disc)
Audio CD
WMA
(8 cm / 12 cm disc)
Windows Media Audio file. A type of coding / decod-
ing developed by Microsoft Corp.
In addition, this unit plays DVD-R, DVD+R, DVD-RW,
DVD+RW, and CD-R / CD-RW that contains audio
titles, MP3, WMA, and/or JPEG files.
JPEG
Joint Pictures Expert Group. JPEG is a compressed
file format that allows you to save images with no
limit on the number of colors.
Not es:
•
Depending on the conditions of the recording
equipment or the CD-R/RW (or DVD -R, DVD +R,
DVD -RW, DVD +RW) disc itself, some CD-R/RW
(or DVD -R, DVD +R, DVD -RW, DVD +RW) discs
cannot be played on the unit.
Title (DVD only)
A title is generally a distinct section of a DVD disc.
For example the main feature could be title 1, a docu-
mentary describing how the film was made could be
title 2, and cast interviews could be title 3. Each title
is assigned a reference number enabling you to
locate it easily.
•
•
•
Only plays if DVD-RW is recorded in Video mode
and has been finalized.
Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
Chapter (DVD only)
A chapter is a segment of a title such as a scene in
a film or one interview in a series. Each chapter is
assigned a chapter number, enabling you to locate
the chapter you want. Depending on the disc, chap-
ters may not be recorded.
Do not use irregularly shaped CDs (e.g., heart-
shaped or octagonal) since they may result in
malfunctions.
Not es on DVDs
Track
Some playback operations of DVDs may be intention-
ally programmed by software manufacturers. This
unit plays DVDs according to disc content designed
by the software manufacturer, therefore some play-
back features may not be available or other functions
may be added.
A distinct element of audio/visual information, such
as the picture or sound track for a specific language
(DVD), or a musical piece on a video or audio CD.
Each track is assigned a track number, enabling you
to locate the track you want. DVD discs allow one
track of video (with multiple angles) and several
tracks of audio.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Regional Code
About the Remote Control
This DVD+VCR is designed and
manufactured for playback of
region “1” encoded DVD soft-
ware. This unit can play only DVD
discs labeled “1” or “ALL”.
Operation Range
1
ALL
Point the Remote Control at the remote sensor and
press the buttons.
Distance: About 23 ft (7 m) from the front of the
remote sensor.
About 30° in each direction of the front of the
remote sensor.
Not es on Reg ion a l Cod es
Angle:
•
Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your DVD+VCR’s regional
code or the disc cannot play.
Battery installation
Detach the battery cover on the rear of
the Remote Control, and insert two
(R03/AAA) size batteries with 3 and #
aligned correctly.
•
If you try to play a DVD with a different region
code from your player, the message “Check
Regional Code” appears on the TV screen.
Do not mix old and new batteries and never
mix different types of batteries such as stan-
dard, alkaline, etc.
Not es on Cop yr ig h t s:
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent copyright-
ed material without permission.
Selecting the Viewing Source
This product features the copy protection function
developed by Macrovision. Copy protection signals
are recorded on some discs. When recording and
playing the pictures of these discs picture noise will
appear. This product incorporates copyright protec-
tion technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection tech-
nology must be authorized by Macrovision
You must select one of your output sources (DVD or
VCR) to view on the TV screen.
•
If you want to view DVD deck output source:
Press DVD until DVD indicator in the display
window lights and output source of DVD deck
is viewed on the TV screen.
•
If you want to view VCR deck output source:
Press VCR until VCR indicator in the display
window lights and output source of VCR deck
is viewed on the TV screen.
Corporation, and is intended for home and other limit-
ed viewing uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or dis-
assembly is prohibited.
Not es:
Not ice f or Pr og r essive Sca n Use
•
If you insert a disc while the DVD+VCR is in the VCR
mode, the DVD+VCR will switch to DVD mode automati-
cally.
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE. IN CASE OF 525 PROGRESSIVE SCAN
PICTURE PROBLEMS, IT IS RECOMMENDED
THAT THE USER SWITCH THE CONNECTION TO
THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE
ARE QUESTIONS REGARDING OUR TV SET COM-
PATIBILITY WITH THIS MODEL 525p DVD+VCR,
PLEASE CONTACT OUR CUSTOMER SERVICE
•
If you insert a cassette tape without prevention tab while
the DVD+VCR is in the DVD mode, the DVD+VCR will
switch to VCR mode automatically.
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic”, and the
double-D symbol are trademarks of Dolby
Laboratories.
CENTER.
DTS and DTS Digital Out are trademarks of
Digital Theater Systems, Inc.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
a
b
DVD
VCR
REC
PM
TV
c
d e f g
h
i
j k
l
m
n
a
b
c
d
Disc Tray (DVD deck)
DVD+VCR is in timer recording or a timer
recording is programmed (VCR part only).
Insert a disc here.
Cassette Compartment (VCR deck)
Insert a video cassette here.
A cassette is in the VCR deck.
The VCR deck is selected.
VCR
1 POWER
Switches the DVD+VCR ON and OFF.
DVD+VCR is Recording.(VCR part only)
Indicates PM time. (AM is not displayed.)
Lights when TV mode is active.
REC
PM
./m
- DVD: Skip to beginning of current chapter or track,
press twice in quick successions to go to previous
chapter or track. Press and hold button for about two
seconds to search backward.
TV
Indicates total playing time,
elapsed time, remaining time
or current deck status
- VCR: Rewinds the tape during the stop mode or for
fast reverse picture search.
(Playback, Pause, etc).
e
f
N
Starts playback of a disc or tape.
j
k
l
m
Remote Sensor
Point the DVD+VCR Remote Control here.
M/>
DVD: Skip to next chapter or track. Press and hold for
two seconds for a fast forward search.
VCR: Advances the tape during the STOP mode or
for fast forward picture search.
Z EJECT
Ejects the tape in the VCR deck.
CH (V/v)
To scan up or down through memorized channels.
g
h
i
x
DVD/VCR (output select)
Select one of your output sources to view on the TV
screen between DVD and VCR.
Stops playback of the disc or tape.
Z OPEN/CLOSE
Opens or closes the disc tray.
n
LINE2 (VIDEO/AUDIO (L/R) input)
Connect to the audio/video output of an external
source (Audio system, TV/Monitor, Another VCR).
Display Windows
The DVD deck is selected.
DVD
A disc is in the DVD deck.
(Lights when a disc is in the DVD deck
and Flashes when no disc.)
LOCK function
Indicates when the Progressive scan is
[P]
The Lock feature disables the front panel buttons to
prevent children from tampering with this unit.
Simply press LOCK on the remote control to toggle
this feature on and off.
active.
Indicates repeat mode.
Indicates when the DVD+VCR is Locked.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
BACKWARD / FORWARD (m / M)
- DVD: Search backward or forward.
Remote Control
- VCR: Rewinds/Advances the tape during the STOP
mode, for fast backward/forward picture search.
CLEAR Removes a mark on the Marker Search menu.
DISC MENU Accesses menu on a DVD disc.
DISPLAY
Accesses On-Screen Display.
CLK/CNT Switches between the clock, tape counter and
tape remaining modes on the display.
DVD Select the DVD+VCR function mode to DVD.
ENTER Confirms menu selections. Displays functions
on the TV screen.
INPUT Selects the VCR deck’s source
(Tuner, LINE 1, or LINE 2).
LOCK Locks/unlocks front panel buttons.
MARKER Marks any point during playback.
OPEN/CLOSE Opens and closes the disc tray.
EJECT Ejects the tape in the VCR deck.
PAUSE/STEP (X) Pause playback or recording.
Press repeatedly for frame-by-frame
playback.
POWER Switches DVD+VCR ON and OFF.
PROGRAM Shows or hides Program menu.
RANDOM Plays tracks in random order.
CM SKIP
Fast forwards picture search through
30 seconds of recording.
REC/ITR (z) Starts recording. Press repeatedly to set
the recording time.
REPEAT Repeat chapter, track, title or all.
RETURN (O) Removes the setup menu.
SEARCH Displays Marker Search menu.
SETUP/MENU
Accesses or removes DVD Setup menu
and VCR menu.
SKIP (. / >) Go to next chapter or track.
Returns to beginning of current
chapter or track or go to previous
chapter or track.
0-9 Selects numbered options in a menu.
STOP (x) Stops playback or recording.
SUBTITLE Selects a subtitle language.
TITLE Displays the disc’s Title menu, if available.
TV Control Buttons See page 35.
b B v V Selects menu options.
CH/TRK(v/V) Selects VCR channels. Adjusts manually
the tape’s picture onscreen.
N (PLAY) Starts playback.
TV/VCR To view channels selected by the VCR tuner
A-B Repeats sequence between two points (A and B).
SPEED Selects recording speed.
or by the TV tuner.
VCR Select the DVD+VCR function mode to VCR.
ANGLE Selects a DVD camera angle, if available.
ZOOM Enlarges DVD video image.
AUDIO Selects an audio language (DVD).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
Caution
Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause
permanent damage to the unit.
a
b c d e
f
g
h
a
b
ANT.IN
e
f
g
h
AUDIO OUT (Left/Right) (DVD OUT)
Connect the VHF/UHF/CATV antenna to this terminal.
Connect to a TV or other equipment with audio inputs.
VCR IN LINE 1 (VIDEO/AUDIO (Left/Right))
Connect the audio/video output of an external source
(Audio system, TV/Monitor, VCR, Camcorder).
AC Power Cord
Plug into the power source.
RF. OUT
c
d
DVD/VCR OUT (VIDEO/AUDIO (Left/Right))
Connect to a TV with video and audio inputs.
Connect to a TV with RF coaxial inputs.
COAXIAL (DIGITAL AUDIO OUT jack)
(DVD OUT)
Connect to digital (coaxial) audio equipment.
COMPONENT/PROGRESSIVE SCAN VIDEO
OUT (Y Pb Pr) (DVD OUT)
Connect to a TV with Y Pb Pr inputs.
Preparation
Depending on your TV and other equipment there are various ways you can connect the
player. Please refer to the manuals of your TV, VCR, stereo system or other devices as
necessary for additional connection information.
No t e s :
•
The picture and sound of a nearby TV, VCR, or radio may be distorted during playback. Position the units away from
each other or turn off the unit after removing the disc.
•
•
Make sure the DVD+VCR is connected directly to the TV and tune the TV to the correct video input channel.
Do not connect the DVD+VCR’s AUDIO OUT jack to the phono in jack (record deck) of your audio system.
Do not connect the DVD+VCR via another VCR. The DVD image could be distorted by the copy protection system.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
To view or record a CATV channel
Connecting an Antenna
or Cable TV
1. Tune the TV to the DVD+VCR output channel
(CH 3 or 4).
2. Set the DVD+VCR channel selector to the cable
output channel. (Example: CH3)
a
Antenna:
Disconnect the antenna from the rear of the TV and
identify the antenna cable. If it is a round 75 ohm
coaxial cable connect it directly to the jack marked
ANT.IN on your DVD+VCR. If your antenna cable is
flat connect it to a 300-ohm to 75-ohm antenna adap-
tor (not supplied) and slip the adaptor over the
ANT.IN jack. Don’t attempt to screw it into to the
DVD+VCR.
3. Select a channel using the cable converter.
Not es:
•
With this connection, you cannot record one program
while viewing another.
•
If you are using a cable box to tune channels, it is not
necessary to do Auto Channel Set.
b
Cable TV:
If your cable connection has no converter or
descrambler, unscrew the cable from your TV and
attach it to the ANT.IN jack on the DVD+VCR. If a
converter is required connect a coaxial cable from the
wall jack to the IN connector on the converter, and a
coaxial cable from the OUT connector on the convert-
er to the ANT IN on your DVD+VCR. This cable
hookup permits both TV and DVD+VCR operation.
Basic TV Connections
Make one of the following connections, depending on
the capabilities of your TV.
a
Antenna
Antenna
Rear of TV
ANTENNA
INPUT
VIDEO
INPUT
AUDIO INPUT
R
L
OR
OR
R
V
A1
Rear of DVD+VCR
Rear of DVD+VCR
b
C
A2
Y
Pr
Pb
R
L
COMPONENT/PROGRESSIVE SCAN
VIDEO INPUT
AUDIO INPUT
Rear of TV
11
Download from Www.Somanuals.com. All Manuals Search And Download.
RF coaxial connection
Optional TV Connections
These connections support only DVD playback. The
tuner and VCR still output through the RF.OUT (R) or
DVD/VCR OUT (A, V) jacks.
Connect the RF.OUT jack on the DVD+VCR to the
antenna in jack on the TV using the supplied 75-ohm
Coaxial Cable (R).
Component Video / Progressive Scan
connection
How to set the DVD+VCR’s RF output
channel
If your television is a high-definition or “digital ready”
television, you may take advantage of the
DVD+VCR’s progressive scan output for the highest
video resolution possible.
1. When the DVD+VCR is turned off, press and hold
CH (V/v) on the front panel for more than five
seconds. “RF03” or “RF04” appears in the display
window.
1. Connect the COMPONENT/PROGRESSIVE
SCAN VIDEO OUT jacks on the DVD+VCR to the
corresponding in jacks on the TV using an optional
Y Pb Pr cable (C).
2. Press CH (V/v) to change the RF output channel
(RF03 or RF04). Tune the TV to this channel.
3. Turn off the DVD+VCR.
2. Connect the Left and Right AUDIO OUT jacks of
the DVD+VCR to the audio left/right in jacks on
the TV (A2) using the supplied audio cables.
Audio/Video connection
1. Connect the DVD/VCR VIDEO OUT jack on the
DVD+VCR to the video in jack on the TV using
the video cable supplied (V).
No t e s :
•
•
•
When you use Component Video signal, set the
Progressive Scan to “Off” on the setup menu.
2. Connect the Left and Right DVD/VCR AUDIO
OUT jacks on the DVD+VCR to the audio left/right
in jacks on the TV (A1) using the supplied audio
cables.
Progressive scan does not work with the analog video
connections (yellow VIDEO OUT jack).
If your TV does not accept the Progressive Scan format,
the picture will appear scrambled.
Not e:
If you use this connection, set the TV’s source selector to
VIDEO.
Audio Connection for DVD
You can only listen to DVD playback using COAXIAL
(X) and AUDIO OUT (A2) connections. The tuner and
VCR will still be heard through the RF.OUT (R) or
DVD/VCR AUDIO OUT (A1) jack. (See page 11.)
Connecting to an amplifier equipped with two
channel analog stereo or Dolby Pro Logic II/Pro
Logic
Connect the Left and Right AUDIO OUT (or DVD/VCR
AUDIO OUT) jacks on the DVD+VCR to the audio left
and right in jacks on your amplifier, receiver, or stereo
system using the audio cables (A1, A2) supplied.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to an amplifier equipped with two
channel digital stereo (PCM) or to an Audio/Video
receiver equipped with a multi-channel decoder
(Dolby Digital™, MPEG 2, or DTS)
Accessory Audio/Video (A/V) Connections to
DVD+VCR
Connect the VCR IN LINE 1 or LINE 2 jacks on the
DVD+VCR to the audio/video out jacks on your
accessory component, using the optional audio/video
cables. (Refer to page 24 for “Recording from
External Components”.)
1. Connect one of the DVD+VCR’s DIGITAL AUDIO
OUT jacks (COAXIAL X) to the corresponding in
jack on your amplifier. Use an optional digital
(COAXIAL X) audio cable.
2. You will need to activate the DVD+VCR’s digital
output. (See “AUDIO” on page 18).
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video receiver that supports one or more of the
audio formats supported by your DVD+VCR (MPEG 2,
Dolby Digital and DTS). Check the receiver manual
and the logos on the front of the receiver.
Ca u t ion :
Due to the DTS Licensing agreement, the digital
output will be in DTS digital out when DTS audio
stream is selected.
No t e s :
•
•
•
If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will
produce a strong, distorted sound or no sound at all.
Six Channel Digital Surround Sound via digital connec-
tion can only be obtained if your receiver is equipped
with a Digital Multi-channel decoder.
To see the audio format of the current DVD in the
on-screen display, press AUDIO.
Rear of DVD+VCR
A1
A2
X
R
L
COAXIAL
DIGITAL INPUT
AUDIO INPUT
Amplifier (Receiver)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
•
AUTO CLOCK SET
Initial Settings - VCR
The Auto Clock Set feature is set to ON at the fac-
tory. In the ON setting, the DVD+VCR looks for a
channel carrying XDS (Extended Data Services)
information. XDS updates the clock using the
Coordinated Universal Time.
By using the VCR Setup menu, you can make
various adjustments to items such as clock setting,
and timer recordings.
- Use b / B to choose ON or OFF.
Your DVD+VCR allows Remote Control adjustment of
several features.
• DAYLIGHT SAVINGS
You can turn Daylight Savings On or Off manually.
If you choose “AUTO”, the DVD+VCR sets the
clock using the DST information broadcast in the
signal (channel).
General Operation
1. Press VCR on the Remote Control.
- Use b / B to choose AUTO, ON or OFF.
2. Press MENU and the MAIN menu will appear.
• TIME ZONE
You can set your local Time Zone manually. If you
choose “AUTO”, the DVD+VCR sets the clock using
the first Coordinated Universal Time information it
finds in a broadcast signal.
- Use b / B to choose the correct time zone
(AUTO, EASTERN, CENTRAL, MOUNTAIN,
PACIFIC, ALASKA or HAWAII).
No t e s :
3. Use v / V to select the desired menu, then press
•
The Auto Clock feature enables the DVD+VCR to set up
the clock while the DVD+VCR is turned off.
ENTER.
•
There are cases where the TV station does not send or
sends wrong date and/or time information and the
DVD+VCR sets the incorrect time. If this happens we
recommend that you set the clock manually.
4. Use v / V to choose a desired option on the seleted
Menu. Then use b / B to choose a desired setting.
5. Press MENU when finished.
No t e :
Manual Clock Set
Menus remain on-screen for 3 minutes.
Use v / V / b / B to enter the necessary information.
•
•
MONTH : Choose the month.
DAY : Choose the date.
The day of the week will display automatically.
CLOCK
• YEAR : Choose the year.
• TIME : Choose the time.
Press and hold b / B to advance clock continuously.
The DVD+VCR gives you two ways to set the time
and date: the Auto Clock Feature or Manually.
No t e s :
Auto Clock Set
•
If setting the clock manually, “AUTO CLOCK SET” must
set to “OFF”. If it is set to “ON”, an incorrect date and/or
time will be entered again when the DVD+VCR is turned
off.
•
The clock uses the 12-hour system. Be sure to set AM
and PM correctly.
PROGRAM
The Timer Recording function allows you to record up
to 8 programs within a period of one year. (See pages
23-24).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TUNING
SETUP
This DVD+VCR is equipped with a frequency
synthesized tuner capable of receiving up to 181
channels. These include VHF channels 2-13, UHF
channels 14-69 and CATV channels 1-125.
Auto Channel Programming
FUNCTION OSD
The on-screen display can be turned on or off.
AUDIO MODE
The DVD+VCR has two separate audio playback sys-
tems, the high quality VHS Hi-Fi system and standard
NORMAL mono system. The same audio is generally
recorded on both systems. The VHS Hi-Fi system
plays on separate (left and right) channels, and the
NORMAL system plays monaural sound. The normal
track is always played so the cassette can be played
on a DVD+VCR that does not have VHS Hi-Fi.
1. Choose the SOURCE SELECT option, then use
b / B to select TUNER.
Use b / B to switch among TUNER, LINE1, and LINE2.
2. Choose the AUTO CHANNEL SET option, then
use b / B to find channels.
• The tuner will automatically cycle through all available
channels (TV/CATV) in the area and place them in
the tuner’s memory.
BROADCAST TYPE (STEREO / SAP / MONO)
Multichannel Television Sound (MTS) carries stereo
and/or Second Audio Program (SAP) bilingual sig-
nals. Set this display to the desired position when
both MTS stereo and SAP signals are received.
When only one of the MTS signal is received, the
DVD+VCR automatically selects the corresponding
receiving mode (Stereo or SAP) regardless of the
selected position. For normal operation, the display
should be in the STEREO position. The DVD+VCR
will then record a STEREO program when available,
and record a mono program IF the program is NOT
IN STEREO. For weak STEREO and/or SAP broad-
casts, changing the display to mono may give clearer
sound.
• After the AUTO CHANNEL SET is complete, the
TUNING menu will hide and return to the TV screen
automatically.
3. Make sure the TUNING BAND is set appropriately
(TV or CATV).
• TV : If you are using a standard antenna to receive
channels.
• CATV : If you are using basic cable to receive
channels.
To Add or Erase Channels
This feature allows you to add or erase channels
from memory manually.
AUDIO OUTPUT (STEREO / LEFT / RIGHT)
1. Choose the CH. ADD/DEL option, then use b / B
Used during playback [when AUDIO MODE (HI-FI/
NORMAL) is in HI-FI position] for selecting the audio
output signals from the AUDIO OUT terminals (L ch
and R ch), and RF.OUT. This display setting should
normally be left in the stereo position, so that when a
stereo tape is played, the stereo sound will be heard
through the left and right channels. If a mono tape is
played and the audio output is set to stereo, the
same mono sound will be heard from both left and
right channels.
to select a channel to add or erase.
2. Use ENTER to add or erase the channel.
Repeat steps 1 and 2 to add or erase other
channels.
3. Press MENU to return to the TV screen.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
LANGUAGE
Initial Settings - DVD
By using the DVD Setup menu, you can make various
adjustments to items such as picture and sound. You
can also set a language for the subtitles and the
Setup menu, among other things. For details on each
Setup menu item, see pages 16 to 19.
To display and exit the Menu:
Press SETUP to display the menu. A second press of
SETUP will take you back to initial screen.
To go to the next level:
Press B on the Remote Control.
Menu Language
Select a language for the VCR and DVD’s setup
menu and information display.
To go back to the previous level:
Press b on the Remote Control.
Disc Audio / Subtitle / Menu DVD
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
General Operation
1. Press DVD on the Remote Control.
Original: Refers to the original language in which
the disc was recorded.
2. Press SETUP.
Other: To select another language, press number
buttons then ENTER to enter the corresponding
4-digit number according to the language code list
in the reference chapter (see p. 35). If you enter the
wrong language code, press CLEAR.
The Setup menu appears.
3. Use v / V to select the desired option then press
B to move to the second level. The screen shows
the current setting for the selected item, as well
as alternate setting(s).
Off (for Disc Subtitle): Turn off Subtitle.
4. Use v / V to select the second desired option
then press B to move to the third level.
5. Use v / V to select the desired setting then press
ENTER to confirm your selection. Some items
require additional steps.
6. Press SETUP or N (PLAY) to exit the Setup
menu.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4. When the confirm menu appears on your screen
“Cancel” is highlighted as default. Use the b button
to highlight “Enter”.
DISPLAY
5. Pressing ENTER will set this unit to progressive
scan mode.
TV Aspect DVD
No t e s :
•
4:3 :
Select when a standard 4:3 TV is connected.
If you set Progressive Scan to ON in error, you must
reset the DVD+VCR. Press STOP (x) and hold it for
more then five seconds before releasing it. The video
output will be restored to the standard setting, and a
picture will once again be visible on a conventional
analog TV or monitor.
16:9 : Select when a 16:9 wide TV is connected.
Display Mode DVD
Display Mode setting works only when the TV Aspect
mode is set to “4:3”.
•
Do not turn off this DVD+VCR while the “PROGRESSIVE
SCAN MODE” message is displayed in the TV screen.
Letterbox: Displays a wide picture with bands on the
upper and lower portions of the screen.
Panscan: Automatically displays the wide picture on
the entire screen and cuts off the portions that do not
fit.
Progressive Scan DVD
Progressive Scan Video provides the highest quality
pictures with less flickering.
If you are using the Component Video jacks for con-
nection to a TV or monitor that is compatible with a
progressive scan signal, set Progressive Scan to On.
To turn on progressive scan:
Connect component/progressive out of this unit to the
input of your monitor/television, set your television or
monitor to component/progressive Input.
1. Select “Progressive Scan” on the DISPLAY menu
then press B.
2. Select “On” using the v / V buttons.
3. Press ENTER to confirm your selection.
The confirm menu will appear.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO
OTHERS
Each DVD disc has a variety of audio output options.
Set this unit’s AUDIO options according to the type of
audio system you use.
The Auto Play, and B.L.E. settings can be changed.
Auto Play DVD
Dolby Digital / DTS / MPEG DVD
You can set up the DVD+VCR so a DVD disc auto-
matically starts playing whenever the DVD is insert-
ed.
If Auto Play mode is set to On, this DVD player will
search for title that has the longest playback time
and then play back the title automatically.
Bitstream: Select “Bitstream” if you connect the
DVD+VCR’s DIGITAL AUDIO OUT jack to an
amplifier or other equipment with a Dolby Digital,
DTS or MPEG decoder.
PCM (for Dolby Digital / MPEG): Select when
connected to a two-channel digital stereo amplifi-
er. DVDs encoded in Dolby Digital or MPEG will
be automatically downmixed to two-channel PCM
audio.
On: Auto Play function is active.
Off: Auto Play function is not active.
No t e :
Off (for DTS): If you select “Off”, the DTS signal
is not output through the DIGITAL AUDIO OUT
jack.
The Auto Play function may not work for some DVDs.
Sample Freq. (Frequency) DVD
B.L.E. (Black Level Expansion)
If your receiver or amplifier is NOT capable of han-
dling 96 kHz signals, select 48 kHz. When this choice
is made, this unit automatically converts any 96 kHz
signals to 48 kHz so your system can decode them.
To select the black level of playback pictures.
Set your preference and monitor’s ability.
On: Expanded grey scale. (0 IRE cut off)
Off: Standard grey scale. (7.5 IRE cut off)
If your receiver or amplifier is capable of handling 96
kHz signals, select 96 kHz. When this choice is
made, this unit passes each type of signal through
without any further processing.
Check the documentation for your amplifier to verify
its capabilities.
DRC (Dynamic Range Control) DVD
With the DVD format, you can hear a program’s
soundtrack in the most accurate and realistic presen-
tation possible, thanks to digital audio technology.
However, you may wish to compress the dynamic
range of the audio output (the difference between the
loudest sounds and the quietest ones). This allows
you to listen to a movie at a lower volume without
losing clarity of sound. Set DRC to On for this effect.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press ENTER to confirm your rating selection,
then press SETUP to exit the menu.
5. Press OPEN/CLOSE (Z) to activate parental
control.
LOCK (Parental Control)
Password (Security Code)
You can enter or change password.
1. Select “Password” on the LOCK menu then press B.
2. Follow step 2 as shown left column (Rating).
To change the password, select the “Change”,
press ENTER and input the new 4-digit code then
press ENTER. Input it again to verify.
Rating DVD
Some movies contain scenes that may not be suitable
for children to view. Many of these discs contain
parental control information that applies to the com-
plete disc or to certain scenes on the disc. Movies and
scenes are rated from 1 to 8, depending on the area.
DVD video discs may or may not respond to the
parental control setting if the Area code of the disc is
set wrongly. Some discs offer more suitable scenes as
an alternative. Ratings are area dependent.
3. Press SETUP to exit the menu.
If you f or g et you r Secu r it y Cod e
If you forget your security code you can clear it using
the following steps:
1. Press SETUP to display the Setup menu.
The parental control feature allows you to block
access to scenes below the rating you input, thereby
preventing your children from being able to view
material you believe is unsuitable.
2. Input the 6-digit number “210499” and the security
code is cleared.
3. Enter a new code as described above.
1. Select “Rating” on the LOCK menu then press B.
2. To access the Rating, Password and Area Code
features, you must input the 4-digit security code
you created.
Area Code DVD
Enter the Area Code whose standards were used to
rate the DVD video disc, based on the list in the
reference chapter (see p. 36).
If you have not yet entered a security code you are
prompted to do so. Input a 4-digit code and press
ENTER. Enter it again and press ENTER to verify.
If you make a mistake before pressing ENTER,
press CLEAR.
1. Select “Area Code” on the LOCK menu then
press B.
2. Follow step 2 as shown left (Rating).
3. Select a rating from 1 to 8 using the v / V buttons.
1-8: Rating one (1) has the most restrictions and
3. Select the first character using v / V buttons.
rating eight (8) is the least restrictive.
4. Press B and select the second character using
Unlock : If you select unlock, parental control is
not active and the disc plays in full.
v / V buttons.
5. Press ENTER to confirm your area code
selection.
No t e :
If you set a rating for the player, all disc scenes with the
same rating or lower are played. Higher rated scenes are
not played unless an alternate scene is available on the
disc. The alternative must have the same rating or a lower
one. If no suitable alternative is found, playback stops. You
must enter the 4-digit password or change the rating level in
order to play the disc.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
This chapter describes how to operate the VCR and
DVD.
Manual Tracking
To manually adjust the tracking use the CH/TRK (v/V)
buttons on the Remote Control or CH (v/V) on the
front panel during playback.
VCR Tape Playback
Press the VCR button to select the device to be oper-
ated.
No t e s :
•
Vertical jitter requires a very fine adjustment.
•
Tracking is automatically reset to normal when the tape
is ejected or the power cord is unplugged for more than
3 seconds.
Basic Instructions
1. Turn on the TV.
2. Tune the TV to the DVD+VCR output channel
(CH 3 or 4) or if a direct VIDEO/AUDIO
Search
connection is made between the DVD+VCR and
the TV, set the TV’s source selector to VIDEO.
This function lets you visually search for a tape sec-
tion in either direction: forward and reverse. During
the high-speed picture search modes, the audio is
muted and horizontal lines (noise bars) appear. Also,
a short time is needed to stabilize the tape speed
when re-entering the PLAY mode so slight interfer-
ence may be observed during this time.
3. Insert a pre-recorded video cassette.
The
indicator lights and the DVD+VCR
powers on automatically.
4. If the (TIMER) indicator in the display window
is lit press POWER (1) once.
5. If a tape without a safety tab is inserted the unit
starts playback automatically.
To search:
1. Press BACKWARD (m) or FORWARD (M)
If not, press N (PLAY).
during playback.
6. Press STOP (x) to stop playback. If the tape
reaches the end before you press STOP (x) the
DVD+VCR automatically stops, rewinds and
ejects the tape.
2. To return to playback, press N (PLAY).
No t e :
After 3 minutes in SEARCH mode the DVD+VCR returns to
PLAY mode to protect the tape and video heads.
No t e:
It is not necessary to select the tape speed for playback
because it is automatically selected by the DVD+VCR.
Also, during playback the TV/VCR selector switches to
VCR mode automatically.
Still Picture and Frame-by-Frame Playback
1. Press PAUSE/STEP (X) during playback.
A still picture appears on the TV screen and the
audio is muted.
Auto Tracking
2. If the still picture vibrates vertically, stabilize it by
using CH/TRK (v/V) on the Remote Control.
Automatic tracking adjusts the picture to remove
snow or streaks and beings when:
3. Press PAUSE/STEP (X) repeatedly to advance
the video picture one frame at a time.
•
•
•
A tape is played for the first time.
4. To return to playback, press N (PLAY).
The tape speed (SP, LP, SLP) changes.
No t e :
Streaks or snow appear due to scratches on the
tape.
After 5 minutes in STILL mode the DVD+VCR stops to
protect the tape and video heads.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Slow Motion
1. While in still mode, press FORWARD (M). The
tape is played at a speed 1/19 times slower than
the normal speed.
2. Use CH/TRK (v/V) on the Remote Control if
necessary to adjust the tracking.
2. Set the AUDIO OUTPUT option to STEREO so
that the left channel sound (L) is heard from the
left speaker and the right channel sound (R) is
heard from the right speaker.
3. To return to the normal speed, press N (PLAY).
No t e s :
•
During slow motion, audio is muted and horizontal lines
(noise bars) may appear on the TV screen. This is normal.
•
After 3 minutes in SLOW MOTION mode the DVD+VCR
goes back to PLAY mode to protect the tape and video
heads.
CM SKIP (Commercial Skip)
This feature is useful for skipping commercials or
short program segments.
The other options are (LEFT) POSITION, which
results in the left channel sound (L) being heard
from both speakers or (RIGHT) POSITION, which
results in the right channel sound (R) being heard
from both speakers.
1. Press CM SKIP in playback mode.
The DVD+VCR performs a fast forward picture
search through 30 seconds of recording.
3. Insert a cassette and press N (PLAY).
2. Press CM SKIP again to extend the search time
by an addition 30 seconds. The maximum search
time is 3 minutes.
MTS (Multi-Channel TV Sound)
3. When the search is complete, the DVD+VCR
goes into playback mode automatically.
This DVD+VCR can decode MTS stereo and bilingual
(SAP) off-the-air broadcast sound signals. It also
decodes stereo TV sound from local cable companies
as long as they operate on assigned cable frequen-
cies and use the EIA-recommended MTS stereo/bilin-
gual TV sound system.
VHS Hi-Fi Stereo / MTS
Broadcast
Multichannel TV Sound Indicator (MTS)
When you press ENTER one or both of the indicators
appears on the TV Screen.
This DVD+VCR is equipped with the VHS Hi-Fi audio
sound system for recording and playback. The infor-
mation below gives a brief description of Hi-Fi audio
and how to record and play a tape in the Hi-Fi audio
mode.
STEREO
The DVD+VCR can record in stereo onto the VHS
Hi-Fi audio tracks when the BROADCAST TYPE
option is in the STEREO position. The DVD+VCR
can also record mono audio onto the mono audio
track.
Hi-Fi Stereo Audio Sound
A stereo TV with AUDIO/VIDEO input jacks or a
stereo audio system is required for true stereo play-
back. To experience the full and rich stereo sound
available with Hi-Fi recorded tapes, we recommend
the connection of this unit to a home stereo audio
system.
SAP
Some stations transmit a Second Audio Program,
which is used for a second language or additional
information.
1. Set the AUDIO MODE option to HI-FI on the VCR
SETUP menu.
STEREO/SAP
Use the BROADCAST TYPE option to select the
desired recording mode (STEREO or SAP).
21
Download from Www.Somanuals.com. All Manuals Search And Download.
To record one TV program while watching
another
VCR Tape Recording
Basic Instructions
1. Press TV/VCR to select the TV mode during
recording. The TV indicator appears.
1. Turn on the DVD+VCR and TV.
2. Using the TV, select the channel to be viewed.
2. Tune the TV to the DVD+VCR output channel
(CH 3 or 4) or if a direct VIDEO/AUDIO connec-
tion is made between the DVD+VCR and the TV,
set the TV’s source selector to VIDEO.
3. Insert a video cassette with the safety tab intact.
Timer Recording
4. Select the desired channel using CH/TRK (v/V).
5. If you are recording from another source via
audio/video input jacks (at the rear or front panel),
select LINE1 or LINE2 using INPUT.
For unattended recording, you must input the
channels to be recorded and the starting and ending
times.
6. Set the desired recording speed (SP or SLP) by
pressing SPEED. This DVD+VCR is not designed
to record in LP mode.
Things to know before starting
If you try to set the program timer before setting
the clock, “PLEASE SET THE CLOCK” appears
for a moment and then CLOCK menu appears on
the TV screen. Set the time and date before pro-
ceeding.
7. Set the MTS mode (STEREO or SAP). Set the
BROADCAST TYPE option to SAP if applicable.
8. Press REC/ITR (z) and recording starts. The
REC indicator appears in the display window. If a
cassette with no safety tab is loaded, the cassette
is ejected.
1. Turn on the DVD+VCR and the TV.
2. Be sure the TV is set to the DVD+VCR output
channel (3 or 4).
9. Press STOP (x) to stop recording. If the tape
reaches the end before STOP (x) is pressed, the
DVD+VCR stops, rewinds and ejects the tape.
3. Make sure the TUNING BAND in the TUNING
menu is set appropriately (TV or CATV).
Ti p :
Use PAUSE/STEP (X) for best results when making
changes while recording. For example, if you want to
change channels while recording, first press PAUSE/STEP
(X) to put the unit in pause mode, select the desired chan-
nel on the DVD+VCR, and then press PAUSE/STEP (X)
again to resume recording.
4. Press MENU and the MAIN menu appears.
5. Use v / V to choose the PROGRAM menu and
press ENTER.
No t e :
During the VCR recording mode, you cannot change to the
DVD mode.
If eight programs are already entered, the FULLY
PROGRAMMED message appears for a moment
and then PROGRAM 1 appears on the TV screen.
To pause the recording
1. Press PAUSE/STEP (X) to pause the tape during
recording. The REC indicator flashes in the dis-
play window.
6. Use the v / V buttons to switch between the
program options, and the b / B buttons to input
the program information:
2. When you want to continue recording, press
PAUSE/STEP (X) or press REC/ITR (z).
After 5 minutes in PAUSE mode, the DVD+VCR
stops automatically to protect the tape and the
video heads.
Input the month, day, start and stop times of the
program you want to record.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel: Select a TV channel, LINE1 or LINE2. If
you have CABLE TV and use a cable box (con-
verter) you must set the channel to match the
cable box output channel (usually CH 3 or 4).
Change channels on the cable box instead of with
the DVD+VCR. If you use a cable converter, you
can program multiple recordings only on the con-
verter box output channel. This is because the
converter determines what channel you view
through your DVD+VCR.
Checking or Erasing the Timer Program
Programming can be checked whenever the
DVD+VCR is turned on.
1. Press MENU and the MAIN menu appears.
2. Use v / V to choose the PROGRAM menu and
press ENTER.
Speed: AUTO mode determines how much tape
is left and switches the speed from SP to SLP if it
is necessary to complete recording the program.
If this occurs there could be some picture and
sound distortion at the point where the speed
changes.
3. Use b / B to select a program you want to check
Repeat: To record up to 8 programs on a certain
day of every week select WEEKLY. To record up
to 8 programs at the same time Monday through
Friday select DAILY. Otherwise select ONCE.
or erase. To erase the program, press CLEAR.
4. Press MENU to return to the TV screen.
7. Press MENU and the program is memorized by
the DVD+VCR.
Program Priority
8. Additional programs may be entered by repeating
steps 1-7.
If the recording start and end times of preset pro-
grams overlap on the same day (see the example),
the second program is not recorded until the first is
finished.
9. Ensure you insert a tape with the record safety
tab intact before the first programmed time.
10. Press STOP (x) to end timer recording.
No t e s :
•
If you make a mistake or want to change a setting, use
v to select the option and correct it using b / B.
•
If the program preset time is past, the “PAST TIME
PROGRAMMED” message appears on the TV screen.
Return to the incorrect program and program it with the
correct time.
In this example, the first part of program numbers 2
and 3 are not recorded.
•
•
If you enter a past date, the timer recording will be
performed on that date of the next year.
If the power fails or the DVD+VCR is unplugged the
clock and timer settings are kept in memory for only 3
seconds. Otherwise you must reset the clock and timer.
•
•
If the tape indicator is blinking, no tape is loaded.
When you are playing DVD at programmed Recording
time, the DVD+VCR automatically change to VCR mode
and start recording.
•
The DVD+VCR will automatically power off when Timer
Recording ends.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Timer Recording
With this feature you can record for a preset length
without using the program timer.
Extending the Recording Time
The recording time can be extended anytime by
pressing REC/ITR (z). Subsequent presses result in
advancing the recording time by 30-minute
increments.
1. Turn on DVD+VCR and the TV.
2. Be sure the TV is tuned to the DVD+VCR output
channel (CH 3 or 4). If a direct VIDEO/AUDIO
connection is made between the DVD+VCR and
the TV, set the TV’s source selector to VIDEO.
No t e :
If you press PAUSE/STEP (X) during instant timer record-
ing, the instant timer recording is cancelled.
3. Insert a video cassette with the safety tab intact.
4. Select the desired channel using CH/TRK (v/V)
or the number buttons (0-9). The channel number
appears on the TV screen. If you are recording
from another source via audio/video input jacks
(at the rear or front panel), select LINE1 (rear
jacks) or LINE2 (front jacks) by using INPUT.
Recording from External Components
You can record from an external component, such as
a camcorder or VCR, connected to any of the
DVD+VCR’s external inputs.
5. Set the desired recording speed (SP or SLP)
using SPEED. The tape speed appears on the TV
screen.
1. Make sure that the component you want to record
from is connected properly to the DVD+VCR. See
page 13.
6. Press REC/ITR (z) twice. The menu appears on
the TV screen, recording starts, and the
(TIMER) indicator lights.
2. Press INPUT repeatedly to select the external
input to record from.
•
LINE1 (L1): Audio/Video Input mounted on
back panel.
INSTANT TIMER RECORD
CHANNEL
SPEED
2
SP
•
LINE2 (L2): Audio/Video Input mounted on
front panel.
START
LENGTH
NOW
0H30M
3. Load a recordable tape.
4. Set a recording mode (SP or SLP) as necessary
by pressing SPEED repeatedly.
7. Press REC/ITR (z) repeatedly to select the
recording time length. Each time you press this
button the recording time increases 30 minutes
(up to 9 hours). At the end of the recording, the
DVD+VCR will stop recording and shut off.
If you set the time to 0H00M, the DVD+VCR goes
into the normal recording mode. Press STOP (x)
to stop the recording.
5. Play the tape or disc in the external component.
If you have a TV attached to your DVD+VCR,
you can see the video palying.
6. Press REC/ITR (z) once to start recording.
The REC indicator lights in the display window.
7. Press STOP (x) to stop recording.
Not es:
•
Before recording, confirm the recording start position.
•
If your source is copy-protected using CopyGuard, you
will not be able to record it using this unit. See Copyright
on page 8 for more details.
Checking the Recording Time
Press REC/ITR (z) once to check the recording time.
The recalled setting automatically returns to the TV
screen after 6 seconds.
•
To record for a fixed length of time, see Instant Timer
Recording.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Each press of the ENTER changes the TV screen in
the following sequence.
Copying from DVD to VCR
You can copy the contents of a DVD to a VHS tape.
STOP
SP
CH
4
STEREO
1. Insert the disc you wish to copy into the DVD
deck and close the disc tray.
APR 30 , SAT
2:15 PM
2. Insert a blank VHS video tape into the VCR deck.
2:15 PM
0:35:40
3. Find the place on the DVD from which you want
to start dubbing using the PLAY, FF, REW and
PAUSE functions.
REM 1:58
For best results, pause playback at the point from
which you want to record.
Real-Time Counter
If a tape with contents recorded on it is inserted into
the VCR, the real-time counter shows length of the
tape running in hours, minutes, and seconds. Press
CLK/CNT to select the real-time counter display.
Every press of CLK/CNT changes the TV screen as
illustrated below.
4. Press the z REC/ITR. The DVD goes into PLAY
mode and the VCR goes into RECORD mode. If
the DVD disc menu appears, you may need to
press N (PLAY) manually to begin copying.
5. When the DVD is finished playing,
press STOP (x) to end copying.
2:15 AM
CLOCK
0:05:25
COUNTER
REM 1:07
No t e s :
REMAINING TIME
•
If the DVD you are attempting to copy is copy protected,
you will not be able to copy the disc. It is not permitted
to copy Macrovision encoded DVDs (or Discs). “Lock” is
displayed in the display window.
Counter Memory
This feature is useful if there is a section of tape you
want to view immediately after recording or if you
want to return to the same point several times.
•
•
You must stop the copy process manually when the
DVD movie ends, or the unit may replay and record over
and over again.
1. Begin recording or playing a tape.
2. Press CLK/CNT until the real-time counter is dis-
played on the TV screen.
When you stop the DVD playback during copying, the
recording on VCR is stopped automatically.
3. At the point that you want to locate later, reset the
real-time counter to “0:00:00” by pressing CLEAR.
4. Continue to play or record.
5. Press STOP (x) when recording or playback fin-
ishes.
On-Screen Display - VCR
Some of these functions will be displayed every time
the DVD+VCR is operated.
6
Press BACKWARD (m). The tape automatically
stops when the tape counter returns to about
“0:00:00”.
Tape Remaining
❶
❷
❸
❹
❺
This function displays the amount of time remaining
on the tape during recording or playback. Press
CLK/CNT repeatedly until the REM indicator displays
on the TV screen during recording or playback.
The remaining tape length may not be displayed cor-
rectly depending on the condition of the tape and the
kind of the tape (T-140, T-160, or T-210 etc.).
PLAY
SP
HI-FI
CH 4
STEREO
OCT 8 , SAT
2:15 PM
No t e s :
❻
❼
•
•
•
The function displays can be seen displayed on the TV
screen for 5 seconds.
❶ TAPE SPEED DISPLAY
❷ FUNCTION DISPLAY
❸ HI-FI DISPLAY
❺ STEREO / SAP DISPLAY
(MONO is not displayed)
The clock (or tape counter, tape remaining) mode will be
displayed until you press ENTER.
❻ DATE DISPLAY
The tape counter and the remaining tape length indica-
tor appear only when a cassette is inserted. Also, the
remaining tape length indicator appears after any tape
operation.
❼ CLOCK / COUNT/
REMAIN DISPLAY
❹ CHANNEL DISPLAY
25
Download from Www.Somanuals.com. All Manuals Search And Download.
S-VHS Quasi Playback (SQPB)
Additional VCR Information
•
During manual recording, timer recording, Instant
Timer Recording, playback, or fast forward modes,
the DVD+VCR automatically starts rewinding the
tape at the end of the tape. The cassette stops at
the beginning of the tape and is ejected.
•
•
This DVD+VCR can play back S-VHS recorded
tapes, however, it cannot make recordings using
S-VHS format tapes.
SQPB is an abbreviation for S-VHS Quasi
Playback.
•
After you have finished using the DVD+VCR,
rewind, eject, and remove the cassette. Place the
cassette in its protective sleeve to protect it from
dust. It is not necessary to rewind the cassette
before removing it, but if you do, it is ready to play
or record the next time you use it.
Easy Information
If the Extended Data Service (XDS) signals are
provided along with normal TV signal in your area or
during playback of a tape recorded with Extended
Data Service (XDS) signals, the station ID, program
title, and program details are shown on the TV
screen. When viewing a channel with Extended Data
Service (XDS) signals, press ENTER and the station
ID will appear on the TV screen. Press ENTER again
and the program details will appear on the TV screen.
When viewing a tape recorded with Extended Data
Service (XDS) signals, press ENTER twice and the
program title and program details will appear on the
TV screen.
•
•
Be sure the DVD+VCR channel selector is on the
correct channel you wish to record. The channel
that is being recorded can always be checked by
setting the television on the DVD+VCR channel
(CH 3 or 4) and pressing the TV/VCR to turn the
DVD+VCR’s TV indicator off.
Do not attempt to hook up more than one televi-
sion set to the DVD+VCR for either recording or
playback.
Program Details
LENGTH: Indicates the run length of a program.
TIME REMAINING: Indicates the remaining time of a
program.
VCR Auto Play System
RATING: Indicates the rating of the current program
(N/A, G, PG, PG-13, R, NC-17, X and Not Rated). The
rating N/A means that the motion picture ratings are not
applicable to this program.
This DVD+VCR features automatic playback.
When you load a tape with the safety tab removed
the following occurs:
CH
4
•
The Output Source is changed to VCR mode
automatically.
SP
WABC
STEREO
•
•
The power turns on automatically and playback begins.
At the end of the tape, the DVD+VCR stops, then
rewinds.
“Home video”
APR 30 , SAT
2:15 PM
•
The tape is ejected after rewinding and the turns itself
off automatically.
Easy Information Screen
(Station ID)
PROGRAM DETAILS
“Home video”
LENGTH 01:00
TIME REMAINING 00:26
RATING N/A
Not e:
Auto power off does not function during regular DVD play
mode. (DVD+VCR power stays on.)
Easy Information Screen
(Program details)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
General Features
Playing a DVD
Not es:
Unless stated otherwise, all operations described use
the Remote Control. Some features may also be
available on the Setup menu.
Playback Setup
1. Turn on the TV and select the video input source
connected to the DVD+VCR.
DVD
Moving to another TITLE
2. Turn on the audio system (if applicable) and
select the input source connected to the
DVD+VCR.
When a disc has more than one title, you can move
to another title. Press DISPLAY and select desired
title by using number (0-9) or b / B then press
ENTER to move to another title.
3. Press OPEN/CLOSE (Z) to open the disc tray
and load your chosen disc in the tray, with the
playback side down.
4. Press OPEN/CLOSE (Z) to close the tray.
Playback starts automatically. If playback does
not start, press N (PLAY).
DVD
Moving to another CHAPTER
When a title on a disc has more than one chapter,
you can move to another chapter as follows:
In some cases, the disc menu might appear
instead.
•
Press SKIP (> or .) briefly during playback
to select the next chapter or to return to the
beginning of the current chapter.
5. To stop the playback, press STOP (x).
The unit records the stopped point, depending on
the disc. “Xx” appears on the screen briefly.
•
•
Press SKIP (.) twice in quick successions to
step back to the previous chapter.
Press N (PLAY) to resume playback (from the
scene point). If you press STOP (x) again or
unload the disc (“x” appears on the screen.), the
unit will clear the stopped point.
Press OPEN/CLOSE (Z) to remove the disc.
Press OPEN/CLOSE (Z) to close disc tray or
press POWER (1), the disc tray closes automati-
cally and unit turns off.
To go directly to any chapter during DVD play-
back, press DISPLAY and press v / V to select
the chapter icon. Input the chapter number (0-9)
or use b / B.
Slow Motion DVD
If a m en u scr een is d isp la yed
The menu screen may be displayed first after loading
a DVD which offer a menu.
1. Press PAUSE/STEP (X) during playback.
The DVD+VCR will now go into PAUSE mode.
2. Use FORWARD (M) to select the required
DVD
speed: T 1/7, T 1/6, T 1/4, or T 1/2 (forward).
Use the b B v V buttons to select the title/chap-
ter you want to view, then press ENTER to start.
Press TITLE or DISC MENU to return to the menu
screen.
3. To exit Slow Motion mode, press N (PLAY).
Not e:
Slow motion playback in reverse is not possible.
No t e s :
•
If parental control is set and the disc is not within the
rating settings you must input the password.
(See “LOCK” on page 19).
•
DVDs may have a region code. Your player will not play
discs that have a region code different from your player.
The region code for this player is 1 (one).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Still Picture and Frame-by-Frame Playback
Repeat DVD
DVD
You can repeat a title/chapter on a disc.
Press REPEAT during playback to select a desired
repeat mode.
1. Press PAUSE/STEP (X) during playback.
Advance the picture frame-by-frame by pressing
PAUSE/STEP (X) repeatedly.
• Chapter: repeats the current chapter.
• Title: repeats the current title.
• Off : does not play repeatedly.
2. To exit still motion mode, press N (PLAY).
Search DVD
No t e :
1. Press BACKWARD (m) or FORWARD (M)
•
If you press SKIP (>) once during Repeat Chapter
during playback.
playback, the repeat playback cancels.
2. Press BACKWARD (m) or FORWARD (M)
repeatedly to select the required speed.
X2, X4, X16 or X100
A - B
DVD
Repeat A-B
3. To exit SEARCH mode, press N (PLAY).
To repeat a sequence.
1. Press A-B at your chosen starting point. “ A - ”
appears briefly on the TV screen.
Time Search DVD
To start playing at any chosen time on the disc:
2. Press A-B again at your chosen end point.
“A - B” appears briefly on the TV screen and the
repeat sequence begins.
1. Press DISPLAY during playback. The time search
box shows the elapsed playing time.
2. Press v / V to select the time clock icon and
3. Press A-B again to cancel.
“-:--:--” appears.
3. Input the required start time in hours, minutes,
and seconds from left to right. If you enter the
wrong numbers, press CLEAR to remove the
numbers you entered. Then input the correct
numbers.
Zoom DVD
Use zoom to enlarge the video image.
1. Press ZOOM during playback or still playback to
activate the Zoom function. The square frame
appears briefly in the right bottom of the picture.
4. Press ENTER to confirm. Playback starts from the
selected time.
2. Each press of the ZOOM button changes the TV
screen in the sequence: 100% size → 150% size
→ 200% size → 300% size → 400% size →
100% size
Marker Search DVD
To enter a Marker
3. Use the b B v V buttons to move through the
zoomed picture.
You can start playback from up to nine memorized
points. To enter a marker, press MARKER at the
desired point on the disc. The Marker icon appears
on the TV screen briefly. Repeat to enter up to nine
markers.
4. To resume normal playback, press ZOOM repeat-
edly or CLEAR button.
No t e :
Zoom may not work on some DVDs.
To Recall or Clear a Marked Scene
1. During disc playback, press SEARCH. The marker
search menu appears on the screen.
2. Within 10 seconds, press b / B to select a marker
number that you want to recall or clear.
3. Press ENTER and playback starts from the
marked scene. Or, Press CLEAR and the marker
number is erased from the list.
4. You can play any marker by inputting its number
on the marker search menu.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Last Scene Memory DVD
CD
Special DVD Features
This player memorizes last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the player or switch
off the player. If you load a disc that has the scene
memorized, the scene is automatically recalled.
Checking the contents of DVD discs: Menus
DVDs may offer menus that allow you to access
special features. To use the disc menu, press DISC
MENU. Input the corresponding number or use the
b B v V buttons to highlight your selection. Then
press ENTER.
No t e :
This player does not memorize the scene of a disc if you
switch off the player before commencing to play the disc.
Title Menu DVD
1. Press TITLE. If the current title has a menu, the
menu appears on the screen. Otherwise, the disc
menu may appear.
Screen Saver
The screen saver appears when you leave the
DVD+VCR in Stop mode for about five minutes.
2. The menu offers features such as camera angles,
spoken language and subtitle options, and chap-
ters for the title.
3. Press TITLE to exit.
Disc Menu DVD
Press DISC MENU and the disc menu is displayed.
Press DISC MENU again to exit.
Camera Angle DVD
If the disc contains scenes recorded at different cam-
era angles, you can change to a different camera
angle during playback. Press ANGLE repeatedly dur-
ing playback to select a desired angle. Note that the
number of the current angle appears on the display.
Ti p :
The Camera Angle icon is displayed on the TV screen when
alternate angles are available.
Changing the Audio Language DVD
Press AUDIO repeatedly during playback to hear a
different audio language or audio track.
Subtitles DVD
Press SUBTITLE repeatedly during playback to see
the different subtitle languages.
No t e :
If there is no information,
is displayed.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display - DVD
Maintenance and Service
You can display the general playback status on the
TV screen. Some items can be changed using the
menu. To use the on-screen display:
Refer to the information in this chapter before con-
tacting a service technician.
Handling the Unit
1. Press DISPLAY during playback.
2. Press v / V to select an item.
When shipping the unit
The selected item is highlighted.
Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally packed
at the factory.
3. Press b / B to change the setting. You can also
use the number buttons if appropriate (e.g.
inputting the title number). For some functions,
press ENTER to execute the setting.
Keeping the exterior surfaces clean
No t e s :
•
Some discs may not provide all of the features shown
below.
•
Do not use volatile liquids such as insecticide
spray near the unit.
•
If no button is pressed for 10 seconds, the on-screen
display disappears.
•
Do not leave rubber or plastic products in contact
with the unit for a long period of time. since they
leave marks on the surface.
•
If
is displayed, action prohibited or not available.
Cleaning the unit
Example: On-Screen Display during
playing DVD Video
To clean the player, use a soft, dry cloth. If the sur-
faces are extremely dirty, use a soft cloth lightly mois-
tened with a mild detergent solution.
Selection Method
Items
b / B, Numbers
Title Number
Do not use strong solvents such as alcohol, benzine,
or thinner, as these might damage the surface of the
unit.
ENTER
b / B, Numbers
Chapter Number
Time search
ENTER
Numbers, ENTER
Maintaining the Unit
The DVD+VCR is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty or
worn, the picture quality could be diminished.
Depending on the operating environment, regular
inspection and maintenance are recommended after
every 1,000 hours of use.
For details, please contact your nearest authorized
service center.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
MP3 / WMA disc compatibility with this player is
limited as follows:
• Sampling frequency: within 8 - 48 kHz (MP3),
within 32 - 48kHz (WMA)
• Bit rate: within 32 - 320kbps (MP3),
48 - 384kbps (WMA)
Playing an Audio CD or
MP3/WMA Disc
The DVD+VCR can play MP3/WMA formatted record-
ings on CD-ROM, CD-R, or CD-RW discs.
• The player cannot read an MP3/WMA file that
has a file extension other than “.mp3” / “.wma”.
• CD-R physical format should be ISO 9660
• If you record MP3 / WMA files using software
that cannot create a file system (eg. Direct-CD)
it is impossible to playback MP3 / WMA files.
We recommend that you use Easy-CD Creator,
which creates an ISO 9660 file system.
• File names should have a maximum of 8 letters
and must incorporate an .mp3 or .wma extension.
• They should not contain special letters such as
/ ? * : “ < > l etc.
Audio CD
Once you insert an audio CD a menu appears on the
TV screen. Press v / V to select a track then press
N (PLAY) or ENTER and playback starts.
• The total number of contens on the disc should
be less than 1500 files and 300 folders.
This DVD+VCR requires discs and recordings to
meet certain technical standards in order to achieve
optimal playback quality. Pre-recorded DVDs are
automatically set to these standards. There are
many different types of recordable disc formats
(including CD-R containing MP3 or WMA files) and
these require certain pre-existing conditions (see
above) to ensure compatible playback.
MP3 / WMA
1. Press v / V to select a folder, and press ENTER
to see the folder contents.
2. Press v / V to select a track then press
N (PLAY) or ENTER. Playback starts.
Customers should note that permission is
required in order to download MP3 / WMA files
and music from the Internet. Our company has
no right to grant such permission. Permission
should always be sought from the copyright
owner.
ID3 TAG
• When playing a file containing information such as
track titles, you can see the information by pressing
DISPLAY. [ Song, Artist, Album, Comment, Genre ]
• If there is no information, “No ID3 TAG” appear on
the menu screen.
Ti p s :
•
If you are in a file list on the “MUSIC” menu and want to
return to the Folder list, use the v / V to highlight
and press ENTER.
•
On a CD with MP3/WMA and JPEG you can switch
MP3/WMA and JPEG. Press TITLE and “MUSIC” or
“PHOTO” word on top of the menu is highlighted.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Random CD
MP3
WMA
Audio CD and MP3 / WMA
Disc Features
1. Press RANDOM during playback. Random
Playback begins immediately and “Random”
appears on the menu screen.
Pause CD
1. Press PAUSE/STEP (
2. To return to playback, press N (PLAY) or press
MP3
WMA
2. To return to normal playback, press RANDOM
repeatedly until “Random” disappears from the
menu screen.
X) during playback.
PAUSE/STEP ( ) again.
X
Ti p :
By pressing SKIP (> or .) during random playback, the
unit selects another track and resumes random playback.
Moving to another Track
CD
MP3
WMA
CD
Repeat A-B
1. Press SKIP (> or .) briefly during playback
to go to the next track or to return to the begin-
ning of the current track.
1. To repeat a sequence during disc playback press
A-B at your chosen starting point. The Repeat
icon and “A -” appear on the menu screen.
2. Press SKIP (.) twice in quick successions to
2. Press A-B again at your chosen end point. The
Repeat icon and “A-B” appear on the menu
screen, and the sequence begins to play repeat-
edly.
go back to the previous track.
3. You can play any track by inputting its number.
3. To exit the sequence and return to normal play,
press A-B again. The Repeat icon disappears
from the menu screen.
CD
MP3
WMA
Repeat Track / All / Off
You can play a track/all on a disc.
1. Press REPEAT when playing a disc. The repeat
icon appears.
2. Press REPEAT to select a desired repeat mode.
• Track: repeats the current track.
• All: repeats all the tracks on a disc.
• Off(No display): does not play repeatedly.
No t e :
If you press SKIP (>) once during Repeat Track
playback, the repeat playback will be cancelled.
Search CD
MP3
1. Press BACKWARD (m) or FORWARD (M)
during playback.
2. Press BACKWARD (m) or FORWARD (M)
repeatedly to select the required speed:
X2, X4 and X8 backward or forward.
3. To exit SEARCH mode, press N (PLAY).
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat Programmed Tracks
Programmed Playback
1. Press REPEAT when playing a disc. The repeat
icon appears.
The program function enables you to store your
favourite tracks from any disc in the player memory.
A program can contain 30 tracks.
2. Press REPEAT to select a desired repeat mode.
• Track: repeats the current track
1. Insert a disc.
• All: repeats all the tracks on programmed list.
• Off (No display): does not play repeatedly.
AUDIO CD or MUSIC menu appears.
2. Press PROGRAM.
No t e :
E
The
mark will appear to the right of the word
If you press > once during Repeat Track playback, the
repeat playback will be cancelled.
“Program” on the right side of the menu screen.
Erasing a Track from “Program” List
E
1. During STOP mode, press PROGRAM and
mark will appear.
2. Use B / v / V to select the track that you wish to
erase from the Program list.
3. Press CLEAR. Repeat to erase additional tracks
on the list.
Audio CD Program Menu
Erasing the Complete Program List
E
1. During STOP mode, press PROGRAM and
mark will appear.
2. Use B / v / V to select “Clear All” in the
“Program” list, then press ENTER.
MP3/WMA Program Menu
Not e:
No t e :
The programs are also cleared when the disc is removed.
E
Press PROGRAM again, the
exit the Program Edit mode.
mark will disappear to
3. Select a track on the “List”, then press ENTER to
place the selected track on the “Program” list.
Repeat to place additional tracks on the list.
4. Press B.
Select the track you want to start playing on the
“Program” list.
5. Press N (PLAY) or ENTER to start. Playback
begins in the order in which you programmed the
tracks. Playback stops after all of the tracks on
the “Program” list have played once.
6. To resume normal playback from programmed
playback, select a track of AUDIO CD (or MUSIC)
list and then press N (PLAY).
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Slide Show JPEG
Viewing a JPEG Disc
Use v V b B to highlight the
press ENTER.
(Slide Show) then
Using this DVD+VCR you can view discs with JPEG
files.
1. Insert a disc and close the tray. The PHOTO
menu appears on the TV screen.
Still Picture JPEG
1. Press PAUSE/STEP (X) during slide show.
The player will now go into PAUSE mode.
2. To return to the slide show, press N (PLAY) or
press PAUSE/STEP (X) a gain.
Moving to another File JPEG
Press SKIP (> or .) or cursor (b or B) once
while viewing a picture to advance to the next or
previous file.
Zoom JPEG
2. Press v / V to select a folder, and press ENTER.
A list of files in the folder appears.
Use zoom to enlarge the photo image. (see page 28)
If you are in a file list and want to return to the
previous Folder list, use the v / V buttons on the
To rotate picture JPEG
Press v / V during showing a picture to rotate the
picture clockwise or counter clockwise.
remote to highlight
and press ENTER.
3. If you want to view a particular file, press v / V to
highlight a file and press ENTER or N (PLAY).
The selected file will appear for viewing.
While viewing a file, you can press STOP to move
to the previous menu (PHOTO menu).
JPEG disc compatibility with this player is
limited as follows:
Ti p s :
• Depending upon the size and number of JPEG
files, it could take a long time for the DVD+VCR
to read the disc’s contents. If you don’t see an
on-screen display after several minutes, some of
the files may be too large — reduce the resolution
of the JPEG files to less than 5760 (Horizontal) x
3840 (Vertical) pixels and burn another disc.
•
Information and user guidance regarding the current
image is displayed in the lower part of the screen. You
can toggle this bar on and off using RETURN (O).
•
There are three Slide Speed options
>>> (Fast), >> (Normal) and > (Slow)
:
Use v V b B to highlight the Speed. Then, use b / B to
select the option you want to use then press ENTER.
• The total number of contents on the disc should
be less than 1500 files and 300 folders.
•
On a disc with MP3/WMA and JPEG you can switch
MP3/WMA and JPEG. Press TITLE and MUSIC or
PHOTO word on top of the menu is highlighted.
• Some discs may be incompatible due to a differ-
ent recording format or the condition of disc.
• Ensure that all the selected files have the “.jpg”
extensions when copying into the CD layout.
• If the files have “.jpe” or “.jpeg” extensions,
please rename them as “.jpg” file.
• File names without “.jpg” extension will not be
able to be read by this DVD+VCR. Even though
the files are shown as JPEG image files in
Windows Explorer.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
Controlling other TVs with the
remote
Controlling Your TV with the
Supplied Remote
You can control the sound level, input source, and
power switch of non-LG TVs as well. If your TV is list-
ed in the table below, set the appropriate manufactur-
er code.
You can control the sound level, input source, and
power switch of your LG TV with the supplied remote.
You can control your TV using the buttons below.
1. While holding down TV POWER button, press
the number buttons to select the manufacturer
code for your TV (see the table below).
2. Release TV POWER button.
Code numbers of controllable TVs
TV Control
Buttons
If more than one code number is listed, try entering
them one at a time until you find the one that works
with your TV.
Manufacturer
LG / GoldStar
Zenith
Code Number
1 (Default), 2
1, 3, 4
6, 7
8, 9
4
Samsung
Sony
Hitachi
Not es:
•
Depending on your TV, some or all buttons
may not function on the TV, even after enter-
ing the correct manufacturer code.
By pressing
POWER
You can
Turn the TV on or off.
•
•
If you enter a new code number, the code number
previously entered will be erased.
INPUT
Switch the TV’s input source
between the TV and other input
sources.
When you replace the batteries of the remote, the
code number you have set may be reset to the
default setting. Set the appropriate code number
again.
CH +/–
Scans up or down through
memorized channels.
VOL +/–
MUTE
Adjust the volume of the TV.
Turns on or off TV sound.
Not e:
Depending on the unit being connected, you may not
be able to control your TV using some of the buttons.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Codes
Use this list to input your desired language for the following initial settings:
Disc Audio, Disc Subtitle, Disc Menu.
Language
Abkhazian
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali; Bangla
Bhutani
Bihari
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Code
6566
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
Language
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Code
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
Language
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Code
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
Language
Singhalese
Slovak
Slovenian
Somali
Spanish
Sudanese
Swahili
Swedish
Tagalog
Tajik
Code
8373
8375
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance 8277
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Tamil
Tatar
Hebrew
Hindi
Telugu
Thai
Tibetan
Tigrinya
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kirghiz
8279
8285
8377
8365
7168
8382
8372
8378
8368
Uzbek
Vietnamese
Volapük
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Danish
Dutch
English
Esperanto
Estonian
Faroese
Korean
Kurdish
Laothian
Latin
Latvian, Lettish
Sindhi
Area Codes
Choose a area code from this list.
Area
Code
AF
AR
AU
AT
Area
Ethiopia
Fiji
Code
ET
FJ
Area
Code
MY
MV
MX
MC
MN
MA
NP
Area
Saudi Arabia
Senegal
Singapore
Slovak Republic
Slovenia
South Africa
South Korea
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Thailand
Turkey
Code
SA
SN
SG
SK
SI
Afghanistan
Argentina
Australia
Austria
Belgium
Bhutan
Bolivia
Brazil
Cambodia
Canada
Chile
China
Colombia
Congo
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
Malaysia
Maldives
Mexico
Monaco
Mongolia
Morocco
Nepal
Netherlands
Netherlands Antilles AN
New Zealand
Nigeria
Norway
Finland
France
Germany
Great Britain
Greece
Greenland
Islands
Hong Kong
Hungary
India
Indonesia
Israel
Italy
Jamaica
Japan
Kenya
FI
FR
DE
GB
GR
GL
HM
HK
HU
IN
ID
IL
IT
JM
JP
BE
BT
ZA
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CZ
DK
EC
EG
SV
KR
ES
LK
NL
NZ
NG
NO
OM
PK
PA
PY
PH
PL
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
Oman
Pakistan
Panama
Paraguay
Philippines
Poland
Portugal
Romania
Russian Federation RU
Uganda
Ukraine
United States
Uruguay
Uzbekistan
Vietnam
KE
KW
LY
Kuwait
Libya
Luxembourg
PT
RO
El Salvador
LU
Zimbabwe
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Cause
Correction
Symptom
No power.
ꢀ The power cord is disconnected.
ꢀ Plug the power cord into the wall out-
let securely.
ꢀ Refer to page 7.
The power is on, but
the DVD+VCR does
not work.
ꢀ DVD or VCR button is not switched
properly.
ꢀ Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
ꢀ No disc is inserted.
ꢀ No tape is inserted.
No picture.
ꢀ Select the appropriate video input
mode on the TV so the picture from
the DVD+VCR player appears on the
TV screen.
ꢀ The TV is not set to receive DVD+VCR
signal output.
ꢀ Connect the video cable into the jacks
securely.
ꢀ The video cable is not connected
securely.
ꢀ Check the connection.
ꢀ Wrong connection.
ꢀ Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD+VCR.
No sound.
ꢀ The equipment connected with the
audio cable is not set to receive
DVD+VCR signal output.
ꢀ Connect the audio cable into the jacks
securely.
ꢀ The audio cables are not connected
securely.
ꢀ Turn on the equipment connected with
the audio cable.
ꢀ The power of the equipment connected
with the audio cable is turned off.
ꢀ Set the AUDIO options to the correct
position.
ꢀ The AUDIO options are set to the wrong
position.
ꢀ Clean the disc.
ꢀ The disc is dirty.
The playback picture is
poor.
ꢀ Check tuning, carry out tuning again.
ꢀ Clean video heads.
ꢀ The TV channels are not tuned in properly.
ꢀ Tape heads are dirty.
ꢀ Use CH/TRK (v/V) for manual track-
ing adjustment while tape is playing.
ꢀ Tape is a rental or was recorded on
another VCR.
ꢀ Make sure that your TV can support
525p Progressive scan picture or set
Progressive scan to off.
ꢀ This unit can only output 525p
Progressive scan picture.
The “PROGRESSIVE
SCAN MODE”
message remains to be
displayed.
ꢀ Keep pressing the STOP button for
more than 5 seconds.
ꢀ DVD+VCR was turned off while setting
the Progressive scan mode.
ꢀ The Progressive Scan is set to On on
the setup menu but is connected to a
standard(analog) television with compo-
nent video input.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Cause
Correction
Symptom
ꢀ An unplayable disc is inserted.
ꢀ Insert a playable disc. (Check the disc
type and Regional code.)
The DVD+VCR does
not start playback.
ꢀ Place the disc with the playback side
ꢀ The disc is placed upside down.
down.
ꢀ Place the disc on the disc tray correctly
inside the guide.
ꢀ The disc is not placed within the
guide.
ꢀ Clean the disc.
ꢀ The disc is dirty.
ꢀ Cancel the Rating function or change
the rating level.
ꢀ The Rating level is set.
ꢀ Eject the tape in.
ꢀ Is the cassette compartment empty?
Video tape cannot be
inserted.
ꢀ Audio mode is not set properly.
No Hi-Fi sound
ꢀ Select STEREO by repeatedly pressing
AUDIO on the Remote Control.
ꢀ Remove the obstacle.
The Remote Control
ꢀ There is an obstacle in the path of the
does not work properly.
Remote Control and this unit.
ꢀ Replace the batteries with new ones.
ꢀ The batteries in the Remote Control
are exhausted.
ꢀ Point the Remote Control at the remote
ꢀ The Remote Control is not pointed at
sensor of the DVD+VCR.
the remote sensor of the DVD+VCR.
ꢀ Operate the Remote Control within 23ft
ꢀ The Remote Control is too far from
(7m).
the DVD+VCR.
ꢀ When using a VCR, first press the VCR
button. When using a DVD, first press
the DVD button.
ꢀ This Remote Control use the same
buttons for VCR and DVD functions
(ex.PLAY).
ꢀ Turn camcorder on and operate
properly.
Camcorder image is
not shown.
ꢀ Camcorder is off.
ꢀ Press INPUT to select LINE input
channel (LINE1 or LINE2).
Camcorder image via
AV input to DVD+VCR
is not shown on TV
screen.
ꢀ DVD+VCR SOURCE SELECT is not
set to LINE1 or LINE2.
Timer recording is not
possible.
ꢀ Set clock to correct time.
ꢀ Clock in DVD+VCR is not set to
correct time.
ꢀ Timer has been programmed
ꢀ Reprogram Timer.
incorrectly.
ꢀ Reprogram Timer and turn DVD+VCR
off to enable timer.
ꢀ
indicator light does not appear after
programming timer.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
General
Power requirements
120V, 60 Hz
Power consumption
Dimensions (approx.)
Weight (approx.)
Operating temperature
Operating humidity
Signal system
16 W
16.9" X 3.1" X 10.4" (430 X 78.5 X 265 mm) (w x h x d)
9.24 lbs (4.2 kg)
5˚C to 40˚C (41˚F to 104˚F)
5 % to 90 %
NTSC
Inputs
ANTENNA IN
VHS VIDEO IN(LINE1, 2)
VHS AUDIO IN(LINE1, 2)
75 ohms (VHF/UHF/CATV)
1 V (p-p) 75 ohms, sync negative, RCA jack x 2
-6.0 dBm more than 47 ohms, RCA jack (L, R) x 2
Outputs
VIDEO OUT
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Audio output (digital audio)
Audio output (analog audio)
RF OUT
1 V (p-p) 75 ohms, sync negative
(Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack x 2
0.5 V (p-p), 75 ohms, RCA jack x 1
2.0 Vrms (1 KHz, 0 dB), 600 ohms, RCA jack (L, R) x 1
Channel 3 or 4 (Adjustable)
VCR Specifications
Head system
Timer
Tape speed
Tape width
Four head helical scan azimuth system
12-hour display type with AM, PM
SP: 33.35 mm/sec, LP: 16.67 mm/sec, SLP: 11.12 mm/sec
12.7 mm
Maximum recording time
Rewind time
SP: 2 HOURS (T-120), SLP: 6 HOURS (T-120)/8 HOURS (T-160)
About 3 minutes (T-120)
Channel coverage
Frequency range
Signal-to-noise ratio
Dynamic range
VHF: 2-13, UHF: 14-69, CATV: 1-125 (4A, A-W, W+1 - W+84, A-5 - A-1)
20 Hz to 20 kHz
More than 43 dB
More than 88 dB
Channel separation
More than 60 dB
DVD Specifications
Laser system
Frequency response
Semiconductor laser, wavelength 650 nm
DVD (PCM 96 kHz): 8 Hz to 44 kHz,
DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
Signal-to-noise ratio
Harmonic distortion
Dynamic range
More than 100 dB (ANALOG OUT jacks only)
Less than 0.008%
More than 95 dB (DVD/CD)
Accessories:
Video cable x 1, Audio cable (L/R) x 1, RF 75-ohm Coaxial Cable x 1, Remote control x 1, Batteries (R03/AAA) x 2
• Design and specifications are subject to change without prior notice.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
ZENITH
LIMITED WARRANTY-USA
Zenith will repair or replace your product, at Zenith’s option, if it proves to be defective in material or workmanship
under normal use, during the warranty period (“Warranty Period”) listed below, effective from the date (“Date of
Installation”) of original consumer purchase of the product. This warranty is good only to the original purchaser of
the product and effective only when used in the United States, excluding U.S. Territories.
WARRANTY PERIOD:
HOW SERVICE IS HANDLED:
This is an Exchange Product. Call 1-800-243-0000 for
instructions on getting the defective unit replaced.
LABOR: 90 DAYS from the Date of Purchase.
PARTS: ONE YEAR from the Date of Purchase.
Please retain dated sales receipt and your box to
return the unit to LG for repair or replacement.
Replacement Units is warranted for the remaining
Shipping charges both ways will be paid by Zenith during
the first 90 days of the Warranty Period. During the
remainder of the Warranty Period (91-365 days), you pay
in-bound shipping charges and Zenith pays return ship-
ping charges.
period of the original warranty.
Visit our website at http://www.zenithservice.com
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE
EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS
WARRANTY PERIOD ABOVE. ZENITH WILL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, OR
INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR PROFITS, IN CONNECTION WITH
THE PRODUCT. SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY
LASTS OR THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITA-
TIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY DOES NOT APPLY TO:
• Damages or operating problems that result from shipping, installation, adjustment of user controls, calibration,
maintenance or failure to maintain, or separate system components; and
• Damages or operating problems that result from normal wear and tear, misuse, abuse, operation outside envi-
ronmental specifications or contrary to the requirements or precautions in the Operating Guide, accident, light-
ning strikes or other natural causes, unauthorized modification or alteration, incorrect electrical current or volt-
age, signal reception or input, software not licensed directly by LG, software errors that do not disable function-
ality, operating and software protocols adopted after the date of manufacture or for outside the US, institutional
or commercial use, or other causes not arising out of defect in material or workmanship.
The cost of repair or replacement under these excluded circumstances shall be borne by the consumer.
CUSTOMER INTER-ACTIVE CENTER NUMBERS:
Call 1-800-243-0000 (24 hours a day, 365 days per year) and select an
appropriate option from the menu.
For Warranty Service, Where to buy,
Product Assistance, or Customer
Assistance
To contact us by mail:
LG Customer Interactive Center, PO Box 240007
201 James Record Road, Huntsville, AL 35824
Attn: CIC
FOR WARRANTY SERVICE:
You must call 1-800-243-0000 (24 hours a day, 365 days per year) and select an appropriate option from the menu
to confirm the product is defective and to obtain a Return Authorization (RA). If the defect has occurred during the
first 90 days of the Warranty Period, Zenith will send you a return-shipping label. After you obtain an RA for return,
please box your unit with a legible copy of the sales receipt and enough packing material to ensure undamaged
delivery of your product. When you receive the label, place it on the box and call the 800# in the instructions for
pick-up. When your unit is received, Zenith will repair or replace your unit in accordance with this Limited Warranty.
ADVANCE SHIPMENT. If a replacement unit is available and you want second day delivery, our service representa-
tive will ask for your credit card number. Zenith requires a reserved deposit by credit card as surety for such
advance shipment. Your credit card will not be charged if you return the defective unit in 10 business days. For
advance shipment, the return label will come with the replacement unit sent to you. Please follow boxing and ship-
ping instructions above.
Marketed and distributed by:
LG ELECTRONICS U.S.A., INC.
1000 SYLVAN AVENUE
GS# 3835RV0016P
Printed in Indonesia
Issue O
ENGLEWOOD CLIFFS, NJ
Download from Www.Somanuals.com. All Manuals Search And Download.
|