LG Electronics Clothes Dryer DLE2512W User Manual

D L E 2 5 1 4 W / D L G 2 5 2 4 W

D L E 2 5 1 2 W / D L G 2 5 2 2 W

Download from Www.Somanuals.com. All Manuals Search And Download.

PRODUCT FEATURES

OUTSTANDING PERFORMANCE

Not to mention unmatched big capacity, you can benefit from good

time efficiency, quiet operation and energy saving system.

DOUBLE-COATED STEEL DRUM

It is coated with one metal coating and the other polymer coating in order to guarantee high

durability and the long life.

ARTISTIC DESIGN

Modern front panel look and big crystal-clear glass door make your house look stylish.

DIGITAL FABRIC CARE

Multi-level temperature control heater takes a better care on your valued clothes.

EASY OF USE

A whole selection of user-friendly functions always make you comfortable with dryer operation.

TABLE OF CONTENTS

PART1. SPECIFICATIONS .....................................................................................................................................3

PART2. IMPORTANT WARRANTY AND SAFETY INSTRUCTIONS .................................................................4-6

PART3. INITIAL STEPS FOR INSTALLING YOUR DRYER .............................................................................7-12

PART4. ACCESSORIES INSTALLATION .......................................................................................................13-14

PART5. ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYER ...............................................................15-18

PART6. ELECTRICAL REQUIREMENTS FOR GAS DRYERS ............................................................................19

PART7. GAS REQUIREMENTS AND INSTRUCTIONS........................................................................................20

PART8. EXHAUST REQUIREMENTS AND MAINTENANCE..........................................................................21-22

PART9. OPERATING YOUR DRYER...............................................................................................................23-28

PART10. TROUBLESHOOTING GUIDE ..........................................................................................................29-31

LG DRYER LIMITED WARRANTY ........................................................................................................................32

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 1

SPECIFICATIONS

I Name

: Electric and Gas Dryer

I Power supply

: Please refer to the rating label regarding detailed

information.

I Size

: 68.6 X 96.5 X 73.0 (cm)

I Dryer capacity : IEC 7.0 cu.ft.

I Weight : 126(Ibs)

Specifications are subject to change by manufacturer.

I ACCESSORIES

Dryer rack (1 each)

Stacking kit (1 each)

Purchased Separately

Pedestal (1 each)

Purchased Separately

See page 26 for how to use.

See page 13 for how to use.

See page 14 for how to use.

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 2

IMPORTANT WARRANTY AND SAFETY INSTRUCTIONS

SEEKING WARRANTY ASSISTANCE

Warranty Service. The warranty for your dryer is printed the end of this manual.

Warranty service is available by contacting your nearest LG Service Center and, for warranty period

from the date of purchase, if this dryer is installed and operated according to the instructions in this

manual, LG will repair or replace any of its mechanical or electrical parts if they are defective in

material or workmanship.

WARNING!

For your safety, the recommendations in this manual must be followed. To reduce the risk

of fire or explosion, electric shock, or to prevent property damage, personal injury, or

death when using your appliance, follow basic precautions, including the following.

Warranty Restriction: If the dryer is subjected to other than private family use, all warranty

coverage is effective for only 90 days.

You will need the complete model and serial numbers when requesting information. We recommend

that you staple your sales slip or cancelled check here, because proof of original purchase date is

needed to obtain warranty service. Your dryer’s model and serial numbers are located on the Model

and Serial Number Plate located on the front of the dryer behind the door.

Use the space below to record the model number and serial number of your new LG dryer.

Model No.

Serial No.

Date of Purchase

❈ Staple your receipt hear.

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 2

IMPORTANT WARRANTY AND SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WARNING!

to help reduce any risk of electric shock, fire, or other personal or property injury

when using your dryer, please exercise care and follow basic safety precautions,

including the following:

1) Read all instructions before using the appliance.

8) Do not repair or replace any part of the appliance or

attempt any servicing unless specifically

2) Do not dry articles that have come into contact with

gasoline, dry-cleaning solvents, or other flammable

or explosive substances, as they give off vapors that

could ignite or explode.

recommended in the user-maintenance instructions.

9) Do not use heat to dry articles containing foam

rubber or similarly textured rubber-like materials.

3) Do not allow children to play on or in the appliance.

Close supervision of children is necessary when

using the appliance.

10) Clean lint screen before or after each load.

11) Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of

lint, dust, and dirt.

4) Before the appliance is removed from service or

discarded, remove the door to the drying

compartment.

12) The interior of the appliance and exhaust duct

should be cleaned periodically by qualified service

personnel.

5) Do not reach into the appliance if the drum is

moving.

13) Do not place items exposed to cooking oils in your

dryer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause a

load to catch fire.

6) Do not install or store this appliance where it will be

exposed to the weather.

7) Do not tamper with controls.

14) Do not use fabric softners or products to eliminate

static unless recommended by the manufacturer of

the fabric softner or product.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

Do not modify the plug provided with the appliance: if

it will not fit the outlet, have a proper outlet installed by

a qualified electrician.

This appliance must be grounded. In the event of

malfunction or breakdown, grounding will reduce the

risk of electric shock by providing a path of least

resistance for electric current. This appliance is

equipped with a cord having an equipment-grounding

conductor and a grounding plug. The plug must be

plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local

codes and ordinances.

This appliance must be connected to a grounded metal,

permanent wiring system or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead

on the appliance.

WARNING - Improper connection of the equipment-

grounding conductor can result in a risk of electric

shock. Check with a qualified electrician or service

person if you are in doubt as to whether the appliance is

properly grounded.

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 2

IMPORTANT WARRANTY AND SAFETY INSTRUCTIONS

WHAT TO DO IF YOU SMELL

GAS:

• Do not try to light a match or cigarette, or turn

on any gas or electrical appliance.

WARNING!

• Do not touch any electrical switches. Do not

use any phone in your building.

• Keep flammable materials and vapors, such

as gasoline, away from dryer.

• Place dryer at least 18 inches above the floor

for a garage installation.

• Clear the room, building or area of all

occupants.

• Failure to do so can result in death,

explosion or fire.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions carefully.

• If you cannot reach your gas supplier, call the

fire department.

California safe drinking water and

toxic enforcement act

WARNING

To reduce the risk of fire or explosion, electric

shock, property damage, personal injury or death

when using this appliance, please follow all

instructions and information, including those in

this manual and instructions and information

provided by your gas supplier, including the

following:

This act requires the governor of California to

publish a list of substances known to the state to

cause cancer, birth defects or other reproductive

harm and requires businesses to warn customers

of potential exposure to such substances.

Gas appliances can cause minor exposure to four

of these substances, namely benzene, carbon

monoxide, formaldehyde and soot, caused

primarily by the incomplete combustion of

natural gas or LP fuels.

• Do not store or use any gasoline, dry-cleaning

solvents any other flammable vapors or

liquids in the area surrounding this appliance.

• Do not dry anything that has ever had anything

flammable on it, even after washing.

Properly adjusted dryers will minimize

combustion. Exposure to these substances can be

minimized further by properly venting the dryer

to the outdoors.

• No washer can completely remove oil. Do not

dry any articles that have ever had any kind of

oil on them, including cooking oil.

• Articles containing foam, rubber, rubber-like

materials, plastic or similar materials should be

dried on a clothesline or by using an air cycle.

• Failure to follow these instructions can result in

fire, death or serious injury.

• A qualified service person or company must

perform installation and service of this

appliance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 3

INITIAL STEPS FOR INSTALLING YOUR DRYER

The following instructions will help guide you through the initial steps of setting up your dryer for use.

Please note that every section of this manual provides important information regarding the preparation and

use of your dryer, and it is important that you review this entire manual before proceeding with any

installation or use. More detailed instructions concerning electrical connections, gas connections, and

exhaust requirements are provided at other parts of this manual.

Certain minimum clearance are required

STEP 1 Positioning the Dryer.

above,behind, and to the sides of the dryer in

the ever you install it any closer of other

recessed area. Those required minimum clearances

are set forth in the picture below. Please also keep the

following instructions in mind when installing in a

closet or recessed area:

• Consider allowing additional clearance for

installation and servicing.

Choose a location with a solid floor for your dryer.

Place the dryer at least eighteen inches above the

floor for a garage installation. After placing the

dryer in the desired location, please confirm that the

dryer has the required clearances through reference

to the following information and manual sections on

Exhaust Requirements and Maintenance.

If you are installing your dryer in a manufactured or

mobile home, please refer to STEP 9 below for

additional instructions.

• Wall,door and flow molding may require additional

clearance.

• Additional space of 1inch (2.5cm) is recommended an

all sides in order to reduce noise transfer.

• Consider space needed for companion appliances.

• For closer installation, the picture below shows the

minimum required ventilation openings for the door.

A louvered door with comparable ventilation openings

are also acceptable.

48.4”

(123 cm)

38.7”

(98.3 cm)

ventilation

hole

27”

(68.6 cm)

29.6”

(75.3 cm)

ventilation

hole

<Closet-Side view>

* Most installations require a minimum 5 1/2 in.

(14 cm) clearance behind the dryer for the exhaust

vent with elbow.

(0 cm)

27"

(68.6 cm)

(0 cm)

<Closet-Front view>

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 3

INITIAL STEPS FOR INSTALLING YOUR DRYER

Once in position, adjust the leveling legs of the dryer

until it is level from left to right and from front to

back. The leveling legs must remain firmly on the

floor and the dryer should not rock. The maximum

slope of the dryer from left to right or from front to

back should not exceed 2.5 cm (1 inch). If the dryer

is not level, and if the slope exceeds 2.5 cm (1 inch),

a load may not tumble properly and internal sensors

may malfunction. Note: Other sections of this

manual also provide important information

concerning the placement of and clearances for your

dryer. Please review this entire manual before

proceeding with any installation.

STEP 2:

STEP 2 Procedure for Reversing

the Door

The door on your dryer can be installed to open

either to the left or the right. Follow these

procedures to reverse the direction in which your

door opens:

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 3

INITIAL STEPS FOR INSTALLING YOUR DRYER

I ALTERNATE EXHAUST DIRECTIONS

STEP 3 Connecting the Exhaust

Remove a screw and exhaust duct.

and Venting System.

In addition to the following warnings, please refer

to manual section on Exhaust Requirements and

Maintenance. IMPORTANT: To reduce the risk of

fire, combustion, and gas accumulation, the dryer

must be vented to the outdoors. Please follow the

instructions (and all others in this manual) very

carefully.

2-1.

Detach and remove a knockout at the

button, left or right side as desired. (Right

Side Vent not available on Gas dryer)

the order of work.

• Do not use thin plastic or foil ducting.

• Use 4" (10.2 cm) diameter rigid or flexible metal

duct (note: venting materials are not supplied with

the dryer, and you should obtain the venting

materials necessary for proper installation)

2-2.

3-1.

Reconnect the another duct[11 in(28cm)]

to the blower housing, and attach the

duct to the base. (Duct is a SVC part)

• Position the dryer where the exhaust duct is

shorter as possible

• Clean old ducts before installing this dryer

• The male end of each section of exhaust duct must

point away from the dryer

Pre-assemble 4" elbow with 4" duct.

Wrap duct tape around joint.

• Use fewer elbow joints as possible

• Use duct tape on all duct joints

• Insulate ductwork that runs through unheated

areas in order to reduce condensation and lint

build-up on pipe walls; and

• PLEASE BE AWARE THAT FAILURE TO

EXHAUST THE DRYER CORRECTLY WILL

VOID THE DRYER’S WARRANTY.

3-2.

Insert elbow duct assembly first through the

side opening and connect the elbow to the

internal duct.

WARNING!

• Use a heavy metal vent.

• Do not use a plastic vent.

• Do not use a metal foil vent.

• Failure to follow these instructions can

result in death or fire.

• Clean old ducts before installing this dryer

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 3

INITIAL STEPS FOR INSTALLING YOUR DRYER

STEP 4 Connection of Gas Supply

STEP 5 Electrical Plug Connections

for Electric Dryer Only.

(Gas dryer only). In addition to the following,

please refer to manual section on Gas Requirements

and Instructions.

Following are several warnings and instructions

concerning making the electrical connection for

electric dryers. More detailed information

concerning the electrical connection is provided at

the manual section entitled Electrical Requirements

For Electric Dryer and it is important that you

thoroughly review that section, and the remainder of

this manual, before taking any steps to install or use

this dryer.

1. Use only a new U.L. listed No. 10 (copper wire

only) three conductor power supply cord kit rated

240 Volts (minimum) 30 Amperes and labeled as

suitable for use in a clothes dryer.

1. New stainless steel flexible connector. Use this type of

connector only if allowed by local codes. Use Design AGA

Certified Connector.

2. Four-wire cord is required for manufactured

(mobile) home installations and use and where

local codes do not allow grounding of this

appliance through neutral.

2. 1/8" NPT Pipe Plug (for checking inlet gas pressure)

3. Equipment Shut-Off Valve-

Installed within 6’ (1.8 m) of dryer

3. The wiring diagram is provided inside the dryer

control hood. Label all wires prior to

disconnection when servicing the dryer, because

wiring errors can cause serious injury to you and

your dryer.

4. Iron Pipe. Shorter than 20’ (6.1 m)

Use 3/8" pipe. Longer than 20’ (6.1 m) - Use 1/2" pipe.

5. 3/8" N.P.T. Gas Connection

1. Confirm that the type of gas available in your

laundry room is appropriate for the dryer. The

dryer is prepared for Natural Gas with a 3/8"

NPT gas connection.

4. For additional instruction on connecting the dryer

to an electrical power source, please refer to this

manual’s section on Electrical Requirements and

Electric Dryer.

2. Remove the shipping cap from the gas

connection at the back of the dryer. Make sure

that you don’t damage the threads of the gas

connection pipe when you remove the shipping

cap.

WARNING!

• Use a new UL approved 30 amp power

supply cord or 10 gauge solid copper wire.

• Use a UL approved strain relief.

• Disconnect power before making electrical

connections.

3. Connect the dryer to your laundry room’s gas

supply using a new flexible stainless steel

connector (as noted below, only use a new

stainless steel flexible connector if allowed by

your local codes).

• Connect neutral wire(white or center wire)

to center terminal.

4. Securely tighten all connections between the

dryer and your laundry room’s gas supply. Turn

on your laundry room’s gas supply and check all

pipe connections (both internal and external) for

gas leaks with a non-corrosive leak detection

fluid.

• Ground wire(green or bare wire) must be

connected to green ground connector.

• Securely tighten all electrical connections

• See installation instructions for complete

instructions.

5. For LP (Liquefied Petroleum) gas connection,

refer to this manual’s section entitled Gas

Requirements and Instructions.

• Failure to do so can result in fire or

electrical shock.

1 0

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 3

INITIAL STEPS FOR INSTALLING YOUR DRYER

STEP 6 Preparation of the Dryer.

STEP 8 Dryer Airflow.

Prior to the first use of this appliance, use all-

purpose cleaning products or a solution of detergent

and water, with damp clothes to remove from the

inside of the dryer drum/drying compartment any

dust or dirt that may have accumulated the inside of

the dryer. Plug-in your dryer after reviewing the

following parts on your dryer’s Electrical

Requirements.

Effective dryer operation requires appropriate dryer

airflow. The adequacy of the airflow can be

measured by evaluating the static pressure. Static

pressure in the exhaust duct can be measured with a

manometer, placed on the exhaust duct

approximately 2 ft. (60.9 cm) from the dryer. Static

pressure in the exhaust duct should not exceed 0.6

inches (1.5 cm). The dryer should be checked with

the dryer running with no load.

Measuring Static pressure

STEP 7 Confirming Heat Source

Operation.

Confirming Heat Source in Gas Dryers

Manometer

Close the door to the dryer drum/drying

compartment and, after completing all steps in this

manual for proper installation of this dryer, start the

dryer on a heat setting, as described more fully in

the operating instructions that accompany the dryer.

After the dryer starts, the igniter will glow red and

the main burner will ignite.

Warning: If all air is not purged from the gas line,

the gas igniter may go off before the gas and the

main burner have ignited. If this happens, the

igniter will re-attempt gas ignition after

approximately two minutes.

Exhaust Duct

MAXIMUM STATIC

PRESSURE IN

WATER COLUMN

Confirming Heat Source in Electric Dryers

Close the door to the dryer drum/drying

0.6 inche (1.5 cm)

compartment and, after completing all steps in this

manual for proper installation of this dryer, start the

dryer on a heat setting, as described more fully in

the operating instructions that accompany the dryer.

The exhaust air or the exhaust pipe should be warm

after the dryer has been operating for three minutes.

1 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 3

INITIAL STEPS FOR INSTALLING YOUR DRYER

4) Electric dryers may be vented to the outside

STEP 9 Additional Instructions

for Installation of Your

Dryer in a Manufactured

or Mobile Home.

using the back, left, right, or bottom panel.

5) Gas dryers may be vented to the outside using the

back, left, or bottom panel. Gas dryer may not be

vented to the outside using the right side panel

because of the burner housing.

6) The dryer exhaust duct must be affixed securely

to the manufactured or mobile home structure,

and the exhaust duct must be made of a material

that will resist fire and combustion, and it is

recommended that you use a rigid or flexible

metal pipe.

The following instructions are applicable to

installations of the dryer in a manufactured or

mobile home. Any installation in a manufactured or

mobile home must comply with the Manufactured

Home Construction and Safety Standards Title 24

CFR, Part 32-80 or Standard CAN/CSA0Z240 MH

and local codes and ordinances. If you are

uncertain whether your proposed installation will

comply with these standards, please contact a

service and installation professional for assistance.

7) DO NOT connect the exhaust duct with any other

duct, vent, chimney, or other exhaust duct.

8) Make sure the dryer has adequate access to

outside fresh air to ensure proper operation. The

opening for outside fresh air must be at least 25

in²(163 cm²).

The following instructions apply to any installation

of the dryer in a manufactured or mobile home:

9) It is important that the clearance of the duct from

any combustible construction be at least 2 inches

(5 cm), and, when venting the dryer to the

outdoors, the dryer can be installed with a

clearances of 1 inch at the sides and back of the

dryer.

1) The gas dryer must be permanently attached to

the floor.

2) The electrical connection for an electric dryer

must be a 4-wire connection. More detailed

information concerning the electrical connection

is provided at the manual section entitled

Electrical Requirements for Electric Dryer

10) Please be aware that venting materials are not

supplied with the dryer. You should obtain the

venting materials necessary for proper

installation.

3) To reduce the risk of combustion and fire, the

dryer must be vented to the outside.

WARNING!

DO NOT vent the exhaust duct under the

manufactured or mobile home.

DO NOT connect exhaust ducts with

metal screws or fasteners that extend

into the duct.

1 2

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 4

ACESSORIES INSTALLATION

Stacking Kit Installation Instructions

To ensure safe and secure installation, please

observe the instructions below.

Secure stacking kit side bracket to the

washer with a screw on the back of bracket.

Repeat Steps 2, 3, 4 for the other side.

WARNING

Do not attempt installation with one person.

Incorrect installation procedure can cause

serious accidents and physical Injuries.

The weight of the dryer and the height of

installation makes the stacking procedure

too risky for one person. This procedure

should be performed by 2 or more

Place the dryer on top of the washer by fitting

legs as shown in the picture. Avoid finger

injuries - be careful not to pinch fingers

between the washer and dryer. Slide washer

slowly backwards to the stopper of kit.

experienced service personnel.

Stacking kit

Place washer firmly on a stable, even and

solid floor as product installation instructions

describes in owner’s manual.

Peel protective paper off the tape from the

stacking kit side bracket.

Insert the front stacking kit. Push the front

stacking kit back to the stoppers of side

stacking kit.

Fit the stacking kit side bracket firmly to the

side of top plate by attaching the double-

faced tape to top plate as picture shows.

Screw both sides of the front kit.

• Do not use stacking kit with a gas dryer in

potentially unstable conditions like a mobile

home.

1 3

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 4

ACESSORIES INSTALLATION

Pedestal Installation Instructions

1 4

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 5

ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS

Following are additional instructions regarding electrical connections and requirements for electric dryers.

Important Warning: To help prevent fire, electric shock, serious injury or death, the wiring and grounding

must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all applicable local

regulations. Please contact a qualified electrician to check your home’s wiring and fuses to ensure that your home

has adequate electrical power to operate the dryer.

120V/ 240V, 60 Hertz, 3-Wire Installation

e) The power cord (pigtail) connection between wall

receptacle and dryer terminal block IS NOT

supplied with dryer. Type of pigtail and gauge of

wire must conform to local codes and with

Instructions for Grounding of your Electric

Electric Dryer:

a) Please note that the wiring diagram is provided

inside the dryer control hood.

instructions mentioned on the following pages.

b) This dryer must be connected to a grounded

metal, permanent wiring system; or an

equipment-grounding conductor must be run

with the circuit conductors and connected to the

equipment-grounding terminal or lead on the

dryer.

f) The method of wiring the dryer is optional and

subject to local code requirements. Refer to

examples on next page.

g) You must select the method by which to wire

your dryer according to local code and ordinance

requirements. Sample methods are included in

the following pages.

c) The dryer has its own terminal block that must

be connected to a separate branch, 60 Hertz,

single phase circuit, AC (alternating current)

circuit, fused at 30 Amperes (the circuit must be

fused on both sides of the line). ELECTRICAL

SERVICE FOR THE DRYER SHOULD BE

OF MAXIMUM RATE VOLTAGE LISTED

ON THE NAMEPLATE. DO NOT CONNECT

DRYER TO 110, 115, OR 120 VOLT

WARNING!

Label all wires prior to disconnection

when servicing the dryer, because

wiring errors can cause serious injury

to you and your dryer.

CIRCUIT. Heating elements are available for

field installation in dryers which are to be

connected to electrical service of different

voltage than that listed on nameplate.

d) If branch circuit to dryer is fifteen feet (4.50 m)

or less in length, use U.L. (Underwriters

Laboratories) listed No. 10 A.W.G. wire

(copper wire only), or as required by local

codes. If over fifteen feet (4.50 m), use U.L.

(Underwriters Laboratories) listed No. 8

A.W.G. wire (copper wire only), or as required

by local codes. Allow sufficient slack in wiring

so dryer can be moved from its normal location

when necessary.

1 5

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 5

ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS

Review the following options to determine the appropriate electrical connection

for your home:

4-wire connection : Direct wire

4-wire receptacle

(NEMA type14-30R)

Important : use 4-wire connection in the places such

as mobile homes and areas where 3-wire connections

is not available.

Use the instructions at this section if your home has

a 4-wire receptacle (NEMA type 14-30R) and you

will be using a UL listed, 120/240 volt minimum,

30 amp, dryer power supply cord.

Prepare minimum 5ft(1.52m) of length in order for

dryer to be replaced.

First, peel 5 inch (12.7cm) of covering material from

end. Make a 5 inch of ground wire bared. After cutting

1¹/2 inch (3.8cm) from 3 other wires. peel insulation

back 1inch (2.5cm). Make ends of 3 wires a hook

shape.

3-wire receptacle

(NEMA type10-30R)

Use the instructions at this section if your home has

a 3-wire receptacle (NEMA type 10-30R) and you

will be using a UL listed, 120/240 volt minimum,

30 amp, dryer power supply cord.

Then, put the hooked shape end of the wire under the

screw of the terminal block(hooked end facing rightward)

and pinch the hook together and screw tightly.

4-wire direct

If this type is available at your home. you will be

connecting to a fused disconnect or circuit breaker

box

1. Connect neutral wire(white) of power cord to center

terminal block screw.

2. Connect red and black wire to the left and right

terminal block screws.

3. Connect ground wire(green) of power cord to external

ground screw and move neutral ground wire of

appliance and connect it to center screw.

3-wire direct

4. Make sure that the strain relief screw is tightened.

and be sure that all terminal block nuts are on tight and

power cord is in right position.

If this type is available at your home. you will be

connecting to a fused disconnect or circuit breaker

box

1 6

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 5

ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS

3-wire connection : Direct wire

Option 1: 4-wire connection with

a Power supply cord.

Important : use 3-wire connection in the places

such as mobile homes and areas where 3-wire

connections is not available.

• lf your local codes or ordinances do not allow the

use of a 3 wire connection, or you are installing

your dryer in a mobile home, you must use a 4-

wire connection.

Prepare minimum 5ft(1.52m) of length in order for

dryer to be replaced.

First, peel 3 ¹/²inch (8.9cm) of covering material

from end and bare 1 inch from the ends.

Then, put the hooked shape end of the wire under

the screw of the terminal block(hooked end facing

rightward) and pinch the hook together and screw

tightly.

1. Connect neutral wire(white) of power cord to

center terminal block screw.

2. Connect red and black wire to the left and right

terminal block screws.

3. Make sure that the strain relief screw is tightened

and be sure that all terminal block nuts are on

tight and power cord is in right position.

1. Connect neutral wire(white) of power cord to

center terminal block screw.

2. Connect red and black wire to the left and right

terminal block screws.

3. Connect ground wire(green) of power cord to

external ground screw and move neutral ground

wire of appliance and connect it to center screw.

4. Make sure that the strain relief screw is tightened.

and be sure that all terminal block nuts are on

tight and power cord is in right position.

1 7

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 5

ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS

Option 3: Optional 3-wire

Option 2: 3-Wire Connection with

connection.

a Power Supply Cord

• If your local codes or ordinances do not allow the

connection of a frame-grounding conductor to the

neutral wire, use the instructions under this

section.

lf your local codes or ordinances permit the

connection of a frame-grounding conductor to the

neutral wire, use these instructions. If your local

codes or ordinances do not allow the connection of

a frame-grounding conductor to the neutral wire,

use the instructions under Section 3: Optional

3-wire connection.

1. Connect neutral wire(white) of power cord to

center terminal block screw.

2. Connect ground wire of appliance and neutral

wire of power cord to center terminal block

screw.

3. Connect red and black wire to the left and right

terminal block screws.

4. Make sure that the strain relief screw is tightened.

and be sure that all terminal block nuts are on

tight and power cord is in right position.

5. Connect a independent ground wire from external

ground connector to proper ground.

1 8

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 6

ELECTRICAL REQUIREMENTS FOR GAS DRYERS

120 Volt, 60 Hertz, with 3-Prong Grounding Plug

Following are additional instructions regarding electrical connections and requirements for gas dryers.

Important Warning: To help prevent fire, electric shock, serious injury or death, the wiring and grounding

must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical

Code, CSA C22.1, and all applicable local regulations. Please contact a qualified electrician to check your home’s

wiring and fuses to ensure that your home has adequate electrical power to operate the dryer.

Electrical Requirements for Your Dryer:

a) Please note that the wiring diagram is provided

inside the dryer control hood. Label all wires

prior to disconnection when servicing the dryer,

because wiring errors can cause serious injury to

you and your dryer.

b) Your dryer is designed to be used on a separate

branch, polarized, three-wire, effectively

grounded, 120 Volt, 60 Hertz, AC (alternating

current) circuit protected by a 15 Ampere fuse,

equivalent fusetron or circuit breaker.

c) Use separately fused circuits for washers and

dryers, and DO NOT operate a washer and a

dryer on the same circuit.

STANDARD 120 VOLT, 60 HERTZ, 3-WIRE

EFFECTIVELY GROUNDED CIRCUIT

Ground

Neutral Side

Round Grounding Prong

Neutral

WARNING!

Do not overload the circuit by operating

other appliances on the same circuit when

this appliance is operating, by using an

extension cord to connect the dryer to the

power source, or by using any adapter to

allow additional cords to connect to the

same outlet.

a) The dryer has a three-prong plug to help guard

against shock. The plug should be plugged

directed into a properly grounded three-prong

receptacle that is rated 120 Volts AC (alternating

current) 15 Amps. This plug, in order to be

properly and fully effective, must be plugged into

a properly installed outlet that is grounded in

accordance with all local codes and ordinances.

WARNING!

b) The dryer must be grounded in order to reduce

the risk of electric shock, including a

malfunction or breakdown.

DO NOT modify the plug provided with

the dryer. If it does not fit the outlet in your

laundry room, a proper outlet will need to be

installed in your laundry room by a qualified

service person or company.

c) If your laundry room does not meet the

specifications required by this manual, or if you

are uncertain whether or not your laundry room

meets these specifications, please have a

qualified service person or company, for example

a qualified electrician or your local electric

company, review your laundry room’s electrical

supply for any problems.

1 9

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 7

GAS REQUIREMENTS AND INSTRUCTIONS

Following are important instructions and information concerning the requirements for the gas supply and service for

gas dryers. Important Warning: The gas supply and service for a gas dryer must comply with all local codes

and ordinances. In the absence of any local codes or ordinances in your area, the gas supply and service for your gas

dryer must comply with the latest edition of the National Fuel Gas Code, ANSI Z223.1/NFPA 54.

1. Gas supply requirements: Liquefied Petroleum

(L.P.) Gas (2,500 Btu/ft3 (93.1 MJ/m3)) service

must be provided at 10 + 1.5 in. water column

pressure.

6. If using a rigid pipe, the rigid pipe should be 1/2

inch IPS. If acceptable under local codes and

ordinances and when acceptable to your gas

supplier, 3/8 inch approved tubing may be used

where lengths are less than 20 feet (6.1m).

Larger tubing should be used for lengths in

excess of 20 feet (6.1m). It is also important that

you use pipe joint compound that is insoluble in

LP gas.

2. Important: DO NOT connect the dryer to the

Liquefied Petroleum (LP) Gas service without

converting the gas value.

3. A qualified technician must perform the LP Gas

conversion. Contact your local gas service branch

if you require additional assistance or

information.

7. To reduce the danger of gas leaks, explosion, and

fire, please follow and observe the following

instructions and WARNINGS:

4. Isolate the dryer from the gas supply piping

system by closing its individual manual shut-off

valve, during any pressure testing of the gas

supply system at test pressure equal to or less

than 2/1 psi (3.45 kPa).

• Connect the dryer to the type of gas shown on the

nameplate;

• Use new flexible stainless steel connectors;

• Use Teflon tape and pipe joint compound

insoluble in LP gas on all pipe threads;

5. Supply Line Requirements. Your laundry room

must have a rigid gas supply line to your dryer.

In the United States, an individual manual shutoff

valve MUST be installed within at least 6 feet

(1.8m) of the dryer, in accordance with the

National Fuel Gas Code ANSI Z223.1. A 1/8 in.

N.P.T. pipe plug must be installed as shown.

• Purge gas supply of air and sediment before

connecting the gas supply to the dryer; in order to

prevent gas valve contamination, before tightening

connection between gas supply and dryer, purge

remaining air until odor of gas is identified; and

• DO NOT use an open flame to inspect for gas

leaks; instead, use a non-corrosive leak detection

fluid.

WARNING!

• Use a new AGA or CSA approved gas

supply line.

WARNING!

DO NOT attempt any disassembly of the

dryer, any disassembly requires the

attention and tools of an authorized and

qualified service person or company.

• Install a shut-off valve.

• Securely tighten all gas connections.

• If connected to LP, have a qualified person

make sure gas pressure does not exceed

13 in. water column.

• Examples of a qualified person include

licensed heating personnel, authorized gas

company personnel, and authorized service

personnel.

• Failure to do so can result in death,

explosion, or fire.

2 0

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 8

EXHAUST REQUIREMENTS AND MAINTENANCE

Following are important instructions and information concerning the exhaust requirements for your dryer.

Important Warning: To reduce the risk of fire, combustion, or accumulation of combustible gases, DO NOT

exhaust dryer air into an enclosed and unventilated area, such as an attic, wall, ceiling, crawl space, chimney, gas

vent, or concealed space of a building. To reduce the risk of fire, DO NOT exhaust the dryer with plastic or thin foil

ducting.

Weather Hood

Type

Number of 90°

Elbows

Maximum length of 4”

(10.2 cm) diameter rigid

metal duct

Maximum length of 4”

(10.2 cm) diameter

flexible metal duct

Recommended

65 feet (19.8 m)

55 feet (16.8 m)

47 feet (14.3 m)

36 feet (11.0 m)

28 feet (8.5 m)

45 feet (13.7 m)

35 feet (10.7 m)

30 feet (9.1 m)

25 feet (7.6 m)

20 feet (6.1 m)

4”

(10.2 cm)

Use Only for Short Run

Installations

55 feet (16.8 m)

47 feet (14.3 m)

41 feet (12.5 m)

30 feet (9.1 m)

22 feet (6.7 m)

35 feet (10.7 m)

27 feet (8.2 m)

21 feet (6.4 m)

17 feet (5.2 m)

15 feet (4.5m)

2-1/2”

(6.35 cm)

NOTE : Deduct 6 feet (1.8 m) for each additional elbow.

It is not recommended to use more than 4 90° elbows.

Exhaust Requirements and Instructions:

3. Rigid metal duct is recommended. Do not install

flexible duct in concealed spaces.

1. Venting materials are not provided with the dryer

and you should obtain the necessary venting

materials locally. For example, the outer end of

exhaust pipe must have a weather hood with

hinged dampers to prevent back-draft when the

dryer is not in use.

Non-combustible flexible metal duct is

acceptable. Do not use plastic or thin foil ducting.

4. DO NOT use sheet metal screws on exhaust pipe

joints or other fastening means which extend into

the duct that could catch lint and reduce the

efficiency of the exhaust system. Secure all joints

with duct tape.

2. The exhaust duct must be four inches (10.2 cm)

in diameter with no obstructions. The exhaust

duct should be kept as short as possible. Make

sure to clean any old ducts before installing your

new dryer.

5. To maximize operating results, please observe the

duct length limitations noted in the chart above.

2 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 8

EXHAUST REQUIREMENTS AND MAINTENANCE

Exhaust and Dryer Maintenance

Cleaning the Lint Screen

1. Clean the lint filter either before drying each load

or after drying each load. Always make sure the

lint filter is clean before starting a new load,

because a clogged lint filter may increase drying

times.

WARNING!

Disconnect the dryer’s electric power

prior to any cleaning or maintenance.

2. To clean, pull the lint screen straight up and roll

any lint off the screen with your fingers. Do not

rinse or wash screen to remove lint, because wet

lint is hard to remove. Push the lint screen firmly

back into place.

1. After one year of use, the interior and complete

exhaust system of the dryer should be examined

and cleaned if necessary.

2. You should inspect and clean the exhaust duct at

least yearly.

3. Always ensure the lint screen is firmly secured

before running the dryer. Running the dryer with

a loose lint screen may cause overheating and

damage to the dryer and articles being dried.

3. Check the weather hoods frequently to ensure

the dampers are moving freely, that the dampers

are not pushed in and that nothing has been set

against the dampers.

4. A qualified service person or company should be

used to perform this maintenance.

4. Some articles may shed more lint than other

towels (for example, towels made of synthetic

fibers and natural fibers), causing the lint screen

to become congested more quickly. Remove lint

from the lint screen before and after drying these

articles, such as new towels.

5. A Flexible Metal Vent Kit, available at extra cost,

can be used to exhaust the dryer when it is placed

in hard to reach places. This Kit comes in two

pieces, one of which is attached to the dryer and

the other is attached to the wall exhaust outlet.

Following attachment of the two separate pieces

to the dryer and the wall, the dryer may be

returned to its final position, after which the two

pieces themselves can be connected.

5. In the event lint falls off of the lint screen and

into the dryer during removal, inspect the exhaust

hood and remove any lint.

6. Laundry detergent and fabric softener residue can

build up on the lint screen, causing longer drying

times. The screen is likely blocked if lint falls off

the screen. In order to prevent this type of build

up, and help ensure proper operation of your

dryer, clean the lint screen with a nylon brush

every six months or, if necessary, more

frequently. The lint filter can also be washed as

follows:

7. Ordinarily, the dryer drum will need no care.

Wipe the exterior of the dryer as required, and

always immediately wipe the exterior of the

dryer in the event any detergent, bleach, or other

washing products is spilled on the dryer, because

these products may cause permanent damage to

the exterior finish of the dryer.

8. Clean the control panel with a damp cloth as

necessary. Warning: spray pre-wash products

may damage the finish of the control panel.

a) After rolling the lint off of the screen with your

fingers, wet both sides of the screen with hot or

warm water.

9. Please clean the lint filter either before drying

each load or after drying each load.

b) Wet a nylon brush with hot water and liquid

detergent and scrub the lint screen with the brush

to remove the buildup of detergent and fabric

softener.

10. Always make sure the lint filter is clean before

starting a new load, because a clogged lint filter

may increase drying times.

11. Annually remove the lint filter and attach it to

the vacuum duct. See item #2 above.

c) Repeat as necessary.

d) After the residue has been removed, rinse screen

with hot water.

12. Please note that the wiring diagram is provided

inside the dryer control hood. Label all wires

prior to disconnection when servicing the dryer,

because wiring errors can cause serious injury

to you and your dryer.

e) After drying the lint screen with a clean towel,

firmly replace the lint screen in your dryer.

2 2

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 9

OPERATING YOUR DRYER

Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for

more detailed information. Important Warning: To reduce the risk of fire, electric shock, or injury to person, read

this entire manual, including the Important Safety Instructions, before operating this dryer.

WARNING!

STARTING YOUR DRYER

Explosion Hazard

Keep flammable materials and vapors, such

as gasoline, away from dryer.

1. Using Your Dryer

Do not dry anything that has ever had

anything flammable on it (even after

washing). Failure to follow these instructions

can result in death, explosion, or fire.

1. Clean lint screen before or after each cycle.

2. Place laundry into dryer and close door.

See Loading.

3. Turn the knob to select the drying cycle you want.

The preset settings for Sensor Dry Cycles or

Manual Cycles will glow. The estimated or actual

cycle time (in minutes) will show in the display.

WARNING!

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any

type of oil on it (including cooking oils).

Items containing foam, rubber, or plastic

must be dried on a clothesline or by using

an Air Cycle. Failure to follow these

instructions can result in death or fire.

2 3

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 9

OPERATING YOUR DRYER

4. Stopping Your Dryer

2. To use a Sensor Dry Cycle

To stop your dryer at any time

• Select an Sensor Dry Cycle.

Press START/PAUSE or open the door.

• Select DRY LEVEL to adjust

how dry you want the load. As

the cycle runs, the control

senses the dryness of the load

and adjusts the time

Pausing or Restarting

To pause the dryer at any time

automatically for the selected

dryness level.

Open the door or press START/PAUSE once.

To restart the dryer

• Select the desired Options.

Close the door. Press START/PAUSE.

• Press START/PAUSE

NOTE: Drying will continue from where the cycle

was interrupted if you close the door and press

START within 10 minutes. If the cycle is

interrupted for more than 10 minutes, the dryer will

shut off. Select new cycle settings before restarting

the dryer.

NOTE: DRY LEVEL selections can only be

available while using Sensor Dry Cycles. Selecting

MORE or LESS automatically adjusts the sensed

time needed.

5. Loading

3. To use a Manual Dry Cycle

When loading your dryer my to:

• Select a Manual Dry Cycle.

• Determine load size by the amount of space the

load requires rather than the weight of the load.

• Press MORE TIME or LESS TIME until the

desired drying time is displayed. Tap MORE

TIME or LESS TIME and the time will change by

1 minute intervals.

NOTE: The MORE TIME or LESS TIME

feature can be used with Manual Dry, Time Dry,

and Rack Dry Cycles.

• Avoid overloading the dryer.

Following these instruction can help reduce your

utility bill, prolong the life of your clothes, and

decrease the likelihood of uneven drying and

wrinkle.

• Press TEMP. CONTROL until

the desired temperature

indicator glows.

Following are sample loads for Super Capacity

Dryers:

Heavy Work Clothes

4 jeans

4 workpants

4 work shirts

• (OPTIONAL STEP) If

desired, select OPTIONS. For

more details, see Options.

2 sweatpants

2 sweatshirts

• Press START/PAUSE. Be sure

the door is closed.

Cotton/Towels

10 bath towels

10 hand towels

14 wash cloths

• If you do not press START/PAUSE within 10

minutes of selecting the cycle, the dryer

automatically shuts off.

Mixed Load

3 sheets (1 king, 2 twin)

4 pillowcases

3 shirts

9 T-shirts

9 shorts

10 handkerchiefs

• If you wish to end your drying cycle after pressing

START/PAUSE, press START/PAUSE again.

3 blouses

2 4

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 9

OPERATING YOUR DRYER

Sensor Dry Preset Cycle Settings

Time*

(Minutes)

Sensor Dry

Temp.

Cycles Load Type

COTTON/TOWELS

Towel, denim pants

Medium

High

Child Lock

This feature allows you to lock your settings to

prevent children from changing them. You can also

use the child lock feature

to prevent unintended cycle or option changes

during dryer operation.

NORMAL

Work clothes,corduroys

Medium

Low

DELICATES

Lingerie, sheets, blouses

* Estimated Time with SENSOR DRY LEVEL

(Normal) setting.

To enable the Child Lock feature:

Press and hold DRY LEVEL for 3 seconds. A single

BEEP Tone is heard, and CL is displayed. To

unlock, press and hold DRY LEVEL for 3 seconds.

The indicator light turns off.

Manual Cycles

Use Manual Cycles to select a specific amount of

drying time and a drying temperature. When a

Manual Cycle is selected, the ESTIMATED TIME

REMAINING display shows the actual time

remaining in your cycle. You can change the actual

time in the cycle by pressing MORE TIME or LESS

TIME.

6. Cycle Descriptions

Select the drying cycle that matches the type of load

you are drying.

(See Sensor Dry or Manual Preset Cycle Settings

charts.)

• Speed Dry

Use for small loads or loads that need a short

drying time.

Sensor Dry Cycles allow you to match the cycle to

the load you are drying. Each cycle dries certain

fabrics at the recommended temperature. A sensor

detects the moisture in the load and automatically

adjusts the drying time for optimal drying

• Air Dry

Use the Air Dry Modifier for items that require

drying without heat such as rubber, plastic and

heat-sensitive fabrics.

• Time Dry

Sensor Dry Cycle

Use this cycle to complete drying if items are still

damp after an Sensor Dry Cycle. Time dry is also

useful for drying heavyweight and bulky items,

such as bedspreads and work clothes.

• Cotton/Towels

Use for drying denims, towels, heavy cottons

(medium-high heat)

• Normal

Use for drying sturdy fabrics such as work casual

clothes (medium heat)

• Delicates

Use for drying synthetic fabrics, washable knit

fabrics, and no-iron finishes (low heat)

2 5

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 9

OPERATING YOUR DRYER

8. Modifiers

Manual Preset Cycle Settings

Default Time*

(Minutes)

Manual Dry

Temp.

Use Modifiers to select temperatures for the Manual

Cycles. Press TEMP. CONTROL until the desired

temperature setting glows. Temperature modifiers

cannot be used with the Sensor Dry Cycles.

Cycles Load Type

SPEED DRY

High

SMALL LOADS

Air Dry

AIR DRY

7. Options

You can customize your cycles by selecting options.

WRINKLE CARE

When using Air Dry

This chart shows examples of items that can be

dried using AIR DRY.

When you select the wrinkle free option, the dryer

will periodically tumble for up to three hours after

to the cycle has completed.

Type of Load

Default Time*

(Minutes)

This option helps to prevent the wrinkle that form

when a load remains in the dryer after the cycle is

completed. The wrinkle care option ends after the

three hours when you push the wrinkle care option

button on, when you open the dryer door

Foam rubber-pillows,

padded bras, stuffed toys

20 - 30

Plastic-Shower curtains,

tableclothes

20 - 30

Rubber-backed rugs

40 - 50

10 - 20

Olefin, polypropylene,

shear nylon

* Reset cycle to complete drying, if needed.

• Check to see that coverings are securely stitched.

• Shake and fluff pillows by hand periodically

during the cycle.

• Dry item completely. Foam rubber pillows are

slow to dry.

NOTE: Air Dry is not available with Sensor Dry

Cycles.

2 6

Download from Www.Somanuals.com. All Manuals Search And Download.

Part 9

OPERATING YOUR DRYER

9. Rack Dry

NOTE: Check the lint screen and remove any lint

accumulated from items dried on the rack.

The dryer rack is shipped in place in your dryer.

Remove and discard any packing material before

use.