32LP645H 47LP645H
39LP645H 55LP645H
42LP645H 60LP645H
®
Lodging Guest Interactive Pro:Centric TVs
Commercial Mode Setup Guide
Note: Selected features shown in this guide may not be available on all models.
EXPERIENCED INSTALLER
EZ-Manager Wizard
pages 11 – 17
Custom Master TV Setup
pages 29 – 32
FTG Mode of Operation
pages 43 – 44
© Copyright 2013 LG Electronics U.S.A., Inc.
P/N: 206-4232 (Rev B)
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
17. Power Cord
Caution: It is recommended that appliances be placed
2. Keep these instructions.
3. Heed all warnings.
upon a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional
outlets or branch circuits. Check the TV specifications to
be certain.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced
with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse,
such as twisting, kinking, or pinching or being closed in a
door or walked upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the appliance.
7. Do not block any ventilation openings. Install in accor-
dance with the manufacturer’s instructions.
8. Do not install near any heat sources, such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
Do not use a damaged or loose power cord. Be sure to grasp
the plug when unplugging the power cord. Do not pull on the
power cord to unplug the TV.
18. Overloading
Do not connect too many appliances to the same AC power
outlet as this could result in fire or electric shock. Do not
overload wall outlets. Overloaded wall outlets, loose or
damaged wall outlets, extension cords, frayed power cords,
or damaged or cracked wire insulation are dangerous. Any of
these conditions could result in fire or electric shock.
10. Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the
point where it exits from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
19. Outdoor Use/Wet Location
Warning: To reduce the risk of fire or electrical
shock, do not expose this product to rain,
moisture or other liquids.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination in order to avoid injury from
tip-over.
Do not touch the TV with wet hands. Do not install this product
near flammable objects such as gasoline or candles or expose
the TV to direct air conditioning.
Do not expose to dripping or splashing and do not place
objects filled with liquids, such as vases, cups, etc., on or over
the apparatus (e.g., on shelves above the unit).
PORTABLE CART WARNING
20. Grounding
Ensure that you connect the earth ground wire to prevent
possible electric shock (i.e., a TV with a three-prong grounded
AC plug must be connected to a three-prong grounded AC
outlet). If grounding methods are not possible, have a quali-
fied electrician install a separate circuit breaker. Do not try to
ground the unit by connecting it to telephone wires, lightning
rods, or gas pipes.
13. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
21. Disconnect Device
14. Never touch this apparatus or antenna during a thunder or
The mains plug is the disconnecting device. The plug must
remain readily operable.
lightning storm.
15. When mounting a TV on the wall, make sure not to install
the TV by the hanging power and signal cables on the back
of the TV.
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn off
this unit by SWITCH.
16. Do not allow an impact shock or any objects to fall into the
(Continued on next page)
product, and do not drop objects onto the screen.
206-4232
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page)
26. Do not touch the ventilation openings, as they may become
hot while the TV is operating.
22. Outdoor Antenna Grounding
27. If you smell smoke or other odors coming from the TV or
hear strange sounds, unplug the power cord, and contact an
authorized service center.
If an outside antenna or cable system is connected to the
product, follow the precautions below.
An outdoor antenna system should not be located in the
vicinity of overhead power lines or other electric light or power
circuits or where it can come into contact with such power
lines or circuits as death or serious injury can occur.
28. Do not press against the front panel of the TV with your
hand or a sharp object (e.g., a nail, pencil, or pen) or make a
scratch on it.
29. Keep the product away from direct sunlight.
Be sure the antenna system is grounded so as to provide
some protection against voltage surges and built-up static
charges.
30. Dot Defect
The LCD panel is a high technology product with resolution
of two million to six million pixels. In a very few cases, you
could see fine dots on the screen while you are viewing the
TV. Those dots are deactivated pixels and do not affect the
performance and reliability of the TV.
Article 810 of the National Electrical Code (NEC) in the U.S.A.
provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna-discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
31. Generated Sound
“Cracking”: A cracking noise that occurs while the TV is
On or when it is turned Off is generated by plastic thermal
contraction due to temperature and humidity. This noise is
common for products where thermal deformation is required.
Antenna Grounding According to NEC, ANSI/NFPA 70
Electrical circuit humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit, which supplies
a large amount of current to operate a product. It varies
depending on the product. This generated sound does not
affect the performance and reliability of the product.
Ground Clamp
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
32. For LCD TV
Grounding Conductor
If the TV feels cold to the touch, there may be a small “flicker”
when it is turned On. This is normal; there is nothing wrong
with the TV. Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue spots. However,
they have no adverse effect on the TV’s performance. Avoid
touching the LCD screen or holding your finger(s) against it for
long periods of time. Doing so may produce some temporary
distortion effects on the screen.
(NEC Section 810-21)
Electric Service
Equipment
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
23. Cleaning
When cleaning, unplug the power cord and wipe gently with
a soft cloth to prevent scratching. Do not spray water or other
liquids directly on the TV as electric shock may occur. Do not
clean with chemicals such as alcohol, thinners or benzene.
24. Transporting Product
Make sure the TV is turned Off and unplugged and that all
cables have been removed. It may take two or more people
to carry larger TVs. Do not press against or put stress on the
front panel of the TV during transport.
25. Ventilation
Install the TV where there is proper ventilation. Do not install
in a confined space such as a bookcase. Do not cover the TV
with cloth or other materials (e.g., plastic) while it is plugged
in. Do not install in excessively dusty places.
4
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 3
–
–
–
–
Setup Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Creating an FTG Configuration File using the
–
–
–
Initiate Configuration or Exit the EZ-Manager Wizard . . 12
TV Configuration Options. . . . . . . . . . . . . . . . . . . . . . . . . . 13
References
Upgrading TV/PTC Software using a USB Memory
Downloading a Splash Screen using a USB Memory
–
–
–
–
–
Channel Icons / Custom Text Labels (2-5-4 +
–
–
Learning / Teaching a Master TV Setup using
Commercial Mode Check / FTG Operation
Learning / Teaching a Master TV Setup using
–
Learning / Teaching a Master TV Setup using
Learning / Teaching a Master TV Setup using
Notes
• Installer Menu content is intended for use primarily by qualified TV electronics technicians.
• Refer to the applicable Quick Reference Guide for additional information on TV installation, specifications, maintenance, and safety instructions.
• Design and specifications subject to change without prior notice. This document provides examples of typical TV displays. Your displays may vary
from those shown in this document.
206-4232
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Commercial Mode Overview
®
This document describes how to set up LP645H Pro:Centric TVs for Commercial Mode operation. LG
commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides
in the TV’s CPU, Protocol Translator Card (PTC), or embedded b-LAN™ (EBL) module, or it resides
externally from the TV (i.e., in a device from the solution provider).
These TV models are capable of Free-To-Guest (FTG) Mode operation via the TV CPU. Alternatively, the
EBL module can be configured either for Pass-through Mode (default) or FTG Mode. When neither the CPU
nor EBL is in FTG Mode, these TV models also allow external control via the TV’s MPI port.
Setup Checklist
Note: This document provides information specific to Commercial Mode operation. Refer to the Quick
Reference Guide for information on TV installation and hardware and cable connections.
Installation
Cable Connections
__ Unpack TV and all accessories.
__ Install batteries in the Installer Remote.
__ Install TV on VESA mount or stand.
Note: It may be advisable to make all cable
connections before installing on VESA mount
or stand, as appropriate.
__ Make all rear jack panel and MPI card slot
connections, as appropriate.
Commercial Mode Setup
__ Complete appropriate procedures as described
in this document for Commercial Mode operation.
Hardware Connections
__ Install any additional hardware as
appropriate to your institution, LAN, etc.
Pass-through Mode
This mode allows you to configure individual TVs for Pro:Centric or FTG Mode via CPU operation and/
or create a Master TV Setup for cloning purposes for TVs that are to remain in Pass-through Mode. This
mode also allows external control via the GAME CONTROL/MPI port on the TV rear jack panel.
There are two methods for configuring individual TVs that are currently in Pass-through Mode: either
using the EZ-Manager Wizard or the Custom Master TV Setup procedure as described in this document.
EZ-Manager Wizard
The EZ-Manager Wizard provides automated or manual options for configuring essential items for
Pro:Centric operation and also provides an option for using a USB memory device to configure the TV.
Use the Installer Remote to make selections and complete each step. See “EZ-Manager Wizard” on pages
11 to 17 for detailed information.
Custom Master TV Setup
The Custom Master TV Setup procedure enables you to create a customized Master TV Setup for cloning
purposes. Use the Installer Remote to configure Installer Menu items as required for TV operation and
set up TV features (Channel, Picture, Audio, etc.). See “Custom Master TV Setup” on pages 29 to 32 for
detailed information.
6
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Commercial Mode Overview (Cont.)
Installer Menu
To create a Master TV Setup, you will need to know how
to access the commercial controller (PTC) Installer Menu
and make changes to the default values as required. If
necessary, familiarize yourself with the Installer Menu and
how to make and save changes. Refer to pages 20 to 28
for information on accessing the Installer Menu and for
detailed descriptions of the Installer Menu items.
xxLP645H PTC INSTALLER MENU
CPU-CTV
000 INSTALLER SEQ
000
UPN 000-000-000-000
PTC V1.00.022
ASIC D279
CPU V3.35.00
TV Setup Menus
On-screen setup menus control the features of the TV.
Use the Installer Remote to access the TV setup menus,
and set the TV features to the desired configuration for
the end user.
Typical Installer Menu
Cloning
Cloning refers to the process of capturing a Master TV
Setup and transferring it to a Target TV. Both TVs must
be in Pass-through Mode and both TVs must be identical
models. The Master TV’s clonable setup menu features
should be configured as part of the Master TV Setup. If
there are features in the Master TV’s setup—channel
icons or labels, digital font options, etc.—that are not set
or that are set incorrectly, those features also will not be
set or will be set incorrectly in the Target TVs. Refer to
pages 34 to 42 for detailed information on cloning
requirements and procedures.
PICTURE
LOCK
TIME
AUDIO
CHANNEL
INPUT
OPTION
MY MEDIA
TV Setup Menus
External MPI Control
To control the TV using an external MPI control device, you must use the TV’s GAME
CONTROL/MPI port for communication purposes. In these TVs, Installer Menu item 118
POWER SAVINGS controls the power circuitry for both the embedded b-LAN module and
the GAME CONTROL/MPI port; therefore, to ensure that the GAME CONTROL/MPI port
circuitry is powered, thus enabling MPI communication, Installer Menu item 118 POWER
SAVINGS must be set appropriately. See Installer Menu item descriptions as well as
Reference section, “b-LAN Setup & Overview,” for further information.
Note: These TV models are not equipped with MPI card slots.
206-4232
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Commercial Mode Overview (Cont.)
FTG Mode
®
This mode enables Pro:Idiom decryption and also allows logical channel mapping of physical channels
to remove the need for dash tuning. TV operation in FTG Mode is based on which element of the TV owns
the FTG Logical Channel Map—the CPU or the EBL. Understanding the application in which the TV will be
used is vital in determining the owner.
As indicated above, FTG mode operation in the LP645H models can be provided either by the TV CPU
or the EBL. These are two separate and distinct FTG Modes of operation, each with its own unique
advantages and requirements as described later in this document. When the TV CPU is configured with
an FTG Channel Map, the CPU controls the operation of the TV, and when the EBL is configured with an
FTG Channel Map, the EBL controls the operation of the TV.
Once it is determined whether the TV CPU or the EBL will own the FTG Channel Map, configuration can
begin. Configuration of either requires a PC application—the LG FTG File Manager for the TV CPU or the
LG FTG Device Configuration Application for the EBL. Each application provides utilities that enable you
to create/edit an FTG Channel Map and configure Installer Menu settings. See “FTG Mode of Operation
Overview” on pages 43 to 44 for further information on FTG Mode operation and configuration.
Remote Management in FTG Mode
When the TV is configured for FTG Mode via CPU, remote management of the FTG Channel Map and
FTG Installer Menu settings is provided by a Pro:Centric server. Refer to the Pro:Centric Server Admin
Client User Guide for further information.
When the TV is configured for FTG Mode via EBL, the b-LAN module, which is internal to the TV, allows
hotel/institution head end equipment (for example, an FMA-LG101) with b-LAN technology to communicate
with the TV to provide remote management of the FTG Channel Map and FTG Installer Menu settings. See
Reference section, “b-LAN Setup & Overview,” for further information.
8
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Pro:Centric Operation
Pro:Centric TV Interactive Menu Features
When running the Pro:Centric application, the interactive Pro:Centric TV enables guests to locate and
select television entertainment using an interactive channel guide, check the daily weather, and view hotel
and surrounding amenities via custom billboards and points-of-interest maps.
Pro:Centric application features include:
• Portal and information screens/pages (including a “Welcome” page) that include branding logos.
• An optional customized user interface (custom “skins”).
• Billboards and points-of-interest maps that can be customized to focus on hotel amenities, local attractions
and businesses, restaurants, news, events, etc.
• An optional Weather billboard that includes a local radar map, current conditions, and a four day forecast.
• An interactive channel guide that provides a channel list with channel icons. An electronic program
guide (EPG) is an optional feature that displays up to three days of programming information viewable
by channel and time.
• Video spooling that enables the hotel to deliver a video file to guest TVs for promotion and information
purposes.
The Pro:Centric server Admin Client web editor/content wizard is provided for customer configuration of
portal messages and billboards/maps.
Note: Customized content is typically defined by the service integrator and/or hotel administrators. LG
does not provide hotel-specific content.
Pro:Centric Interactive Menu Navigation
Use the Pro:Centric TV remote control to operate both interactive menus and regular TV features. Press
PORTAL on the remote to access the interactive menus.
Note: Interactive menu options may vary, depending on Pro:Centric features enabled for the site. The
following are default interactive menus.
Channel Guide
Shows available TV networks and logical channels. When available, EPG
data provides additional channel and program information.
Information
Typically displays information on hotel amenities, for example, restaurants,
in-room dining, business centers, facilities, etc., as well as information on
local weather and attractions.
Help
Provides help for navigating the interactive menus.
Watch TV
Removes the interactive menu from the screen and returns to the previously
tuned TV channel.
206-4232
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Pro:Centric Operation (Cont.)
Pro:Centric Setup
Administration and management options for the Pro:Centric server are described in detail in the
Pro:Centric Server Admin Client User Guide. This document describes only those settings that must be
specified on the TVs.
On the TVs, the Data Channel must be set appropriately to enable Pro:Centric remote management/
administration facilities, while the Pro:Centric Application Mode must be set appropriately to enable the
Pro:Centric application.
• Remote management/administration (TV E-Z Installation): The Pro:Centric server Admin Client provides
remote management/administration facilities for downloading splash screens and software/firmware
updates as well as facilities for downloading the FTG Channel Map and FTG Installer Menu settings for
TVs that are in FTG Mode via CPU.
• Pro:Centric application: The application, which operates in conjunction with FTG and PPV Modes,
comprises the Pro:Centric interactive menus/features described on the previous page. Pro:Centric
application settings are managed via the Pro:Centric Admin Client.
The Data Channel and Pro:Centric Application Mode can be set using one of the following methods:
• When the TV is in a factory default state, the EZ-Manager Wizard provides automated or manual
options for configuring both the Data Channel and the Pro:Centric Application Mode.
The EZ-Manager Wizard also provides a USB Configuration option that enables you to configure a TV
for FTG Mode via CPU using an FTG Configuration (.tlx) file stored on a USB memory device. The FTG
Configuration file incorporates FTG Installer Menu settings, which includes Installer Menu items 098
PRO:CENTRIC and 119 DATA CHANNEL.
Refer to “EZ-Manager Wizard” on pages 11 to 17 for further information on the EZ-Manager Wizard
options.
• If the TV is in Pass-through Mode, set Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL
to the appropriate values. Refer to “Installer Menu” information on pages 20 to 28 for further details. Also,
as necessary, refer to “Custom Master TV Setup” information on pages 29 to 32 and/or cloning
information on pages 34 to 42.
Note: When the TV is in either Pass-through Mode or FTG Mode via CPU, you can also leave Installer
Menu item 119 DATA CHANNEL set to its default value (255) to enable the TV’s Data Channel Auto
Search feature to set the DATA CHANNEL value. See item 119 description on page 28 for additional
information.
• If the TV is in FTG Mode (via CPU or EBL), use the appropriate software to update the Pro:Centric
and Data Channel Installer Menu items and then transfer the FTG Installer Menu settings to the TV in
accordance with the FTG Mode of configuration. Refer to “FTG Mode of Operation Overview” on pages
43 to 44 for further information on FTG Mode operation and configuration. Also—for FTG Mode via CPU
only—see note above regarding the option to use the TV’s Data Channel Auto Search feature to set the
DATA CHANNEL value.
10
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
EZ-Manager Wizard
The primary purpose of the EZ-Manager Wizard is to guide you through the process (automated or manual)
of configuring the essential Installer Menu items for Pro:Centric TV operation. The wizard will appear on the
screen each time the TV is turned ON, until one of its configuration methods has been completed or the
wizard is exited. Use the Installer Remote to make selections and complete each wizard step.
While the EZ-Manager Wizard is intended primarily for Pro:Centric-related configuration, the wizard also
offers Zoning as well as USB configuration options.
• LP645H TVs support the TV Zoning feature, which enables location-specific settings (see Reference
section, “Using the TV Zoning Feature,” for further information). The EZ-Manager Wizard enables you to
set the TV Zone # in the TV as part of the configuration process.
• The EZ-Manager Wizard also enables you to redirect to the TV’s standard USB Download Menu as part
of the configuration process, if desired, to perform USB configuration functions, including FTG Mode via
CPU configuration, cloning, and software upgrades.
• You can connect a USB memory device to the TV at any time while the wizard is in progress (either at the
Welcome level or beyond) to use the LG Smart Install utility to perform USB configuration functions. Any
file(s) you wish to use for configuration purposes must be stored in a folder named “LGSMARTINSTALL”
in the root directory of the USB memory device. See “LG Smart Install Utility” on pages 18 to 19 for
further information.
Caution: Do NOT unplug the TV power cord or remove the antenna cable during the
configuration process, as doing so will interrupt the current step and may corrupt the
configuration data.
Before You Begin
• If you plan to create a Master TV Setup using the procedure described on pages 29 to 32, be sure to
exit the EZ-Manager Wizard in order to avoid setting modes that may restrict the custom setup proce-
dure. See also “Initiate Configuration or Exit the EZ-Manager Wizard” on the following page.
• If it has been completed or exited and therefore does not display, the EZ-Manager Wizard can be
reactivated; however, this requires that you perform an “IN-STOP” to restore factory defaults on the
TV(s). Refer to Reference section, “Restoring Factory Defaults on the TV(s),” for further information.
• Each wizard step is allotted a time frame after which the wizard proceeds without user interaction. If the
Pro:Centric server is configured on the system and if no location-specific settings are required in the TV,
for example, for TV Zone, Label, and/or Room Number settings, you can simply turn ON the TV, and once
initiated, the wizard will proceed through each of the configuration steps with no further user interaction.
• If any of the configuration steps fails, you will see a “Diagnostics” screen with an indication of the failure.
You will then have the opportunity to reinitiate the configuration process from the previous screen or exit
the EZ-Manager Wizard.
206-4232
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EZ-Manager Wizard (Cont.)
Initiate Configuration or Exit the EZ-Manager Wizard
The Welcome screen provides a brief introduction to the EZ-Manager wizard.
EZ-Manager Wizard
Welcome to LG’s EZ-Manager Wizard
• Use this setup wizard to configure the TV for Pro:Centric and/or Free-
To-Guest (FTG) operation.
Select ‘Next’ to continue.
• If a Pro:Centric Server will not be installed and/or you do not wish to use
the wizard to configure this TV for FTG Mode, you may exit the wizard.
Select ‘No Pro:Centric’ to disable the Pro:Centric feature of this TV, or
select ‘Exit’ to quit.
This setup wizard will start automatically in 10 seconds.
No Pro:Centric
Exit
Next
Note: If there is no user action in this screen within 10 seconds, the wizard will proceed to the
first configuration step. Once the wizard has proceeded, it is not possible to return to the Welcome
screen; however, if you simply wish to exit the wizard, you can do so by selecting the “Exit” option
from the subsequent screen(s).
Note: As indicated on the previous page, you may use the LG Smart Install feature to configure
the TV using a USB memory device at any time while the EZ-Manager Wizard is in progress.
However, if you want to use the TV Zoning feature for location-specific configuration purposes,
proceed to the EZ-Manager’s Zone, Label, and Room Number screen and assign a TV Zone # for
this TV before inserting your USB device. See “TV Configuration Options” on the following page
for further information.
From the Welcome screen, you have the following options:
• To proceed with the EZ-Manager Wizard, use the arrow keys on the Installer Remote to select/
highlight Next and press OK. Then, continue to the “TV Configuration Options” section on the
following page.
• To exit the wizard, but retain the use of the Pro:Centric feature of this TV (i.e., Installer Menu
item 119 DATA CHANNEL set to 255) in the future, use the arrow keys on the Installer Remote
to select/highlight Exit and press OK. In the confirmation pop-up window, select OK, and then
press OK once more on the Installer Remote.
• If you do not intend to install a Pro:Centric server on this system and you do not wish to use
the wizard’s Zoning or USB configuration options, exit the wizard as follows: Use the arrow
keys on the Installer Remote to select/highlight the No Pro:Centric option. This will disable the
Pro:Centric feature of this TV (i.e., Installer Menu item 119 DATA CHANNEL will be set to 0) and
exit the wizard. In the confirmation pop-up window, select OK, and then press OK once more on
the Installer Remote.
12
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
EZ-Manager Wizard (Cont.)
TV Configuration Options
From the TV Configuration Options screen, you can choose how to proceed with the configuration of
this TV (assuming you do not opt to exit the wizard—which you may also do at any time).
Note: If you intend to use the Zoning feature on the TV for location-specific
configuration purposes, assign the TV Zone # in the TV BEFORE you continue with
additional configuration.
Z
EZ-Manager Wizard
4
2
3
1
TV Configuration Options
• To configure the TV for Pro:Centric operation, select ‘Next’.
• To set the optional Zoning feature, select ‘Zone & Room Number’.
• To access the TV’s USB Download Menu, select ‘USB Configuration’.
This setup wizard will continue automatically in 60 seconds.
Exit
USB Configuration
Zone & Room Number
Next
Note: If there is no user action in this screen within one minute, the wizard will automatically
continue to the next configuration step.
Use the Left/Right arrow keys on the Installer Remote to navigate between options on this screen.
Each time you select/highlight one of the following options, the screen text and fields will change
in accordance with your selection.
• To continue with Pro:Centric configuration, select Next (default) and press OK on the Installer
Remote. Refer to “Configure Pro:Centric Settings” on pages 15 to 16 for additional information.
• Select Zone & Room Number to set the Zoning feature on this TV. See “Zone and Room
Number Assignments” on the following page for further information.
• The “USB Configuration” option from this screen allows you to access the TV’s USB Download
Menu. See “USB Configuration” on page 17 for further information.
Note: If you have already inserted a USB memory device with the intent to use the LG Smart
Install utility and the Integrated USB Downloading screen is on display, you may still set the Zoning
feature on this TV by selecting Previous to return to the EZ-Manager/TV Configuration Options
screen. Set the Zoning feature as required, and then select USB Configuration and press OK on
the Installer Remote to return to the Integrated USB Downloading screen.
Note: If you choose to exit the EZ-Manager Wizard from this point on, you will have the option to
save any settings made by selecting Save and Exit in the exit confirmation pop-up window. Or,
you can exit the wizard without saving any settings by simply selecting OK in the confirmation
pop-up window.
206-4232
13
Download from Www.Somanuals.com. All Manuals Search And Download.
EZ-Manager Wizard (Cont.)
Zone and Room Number Assignments
You may complete one or more of the fields in the Zone, Label, and Room Number screen or
leave them blank, as desired; however, in order to use the Zoning feature on this TV, you MUST
set the TV Zone # as described below. See Reference section, “Using the TV Zoning Feature,” for
further information on Zone designations. Note that the Zoning feature is only applicable for TVs
that will be configured for FTG Mode via CPU (using an FTG Configuration [.tlx] file) or for TVs
that will be configured via “Teaching” (cloning) using a USB memory device / .tlx file.
Z
EZ-Manager Wizard
4
2
3
1
Zone, Label, and Room Number
If creating Zones for Installer Menu settings and/or Channel Mapping, select the appropriate Zone # (0-8)
based on the Zone in which this TV is installed. (See Commercial Mode Setup Guide for more information.)
•
•
•
Select a Label and/or use the alphanumeric keypad on the remote to input the Room Number.
When done, select ‘Next’ to continue.
Q.MENU
MARK
INPUT
1
4
7
2
5
8
0
3
6
TV
DVD
Zone
0
Label
Room Number
1
.;
i
jl
r
-----
9
/
CC
P
A
G
E
TIMER
DELETE
MUTE
VOL
CH
CHAR/
NUM
DEL
P
O
R
T
A
L
I
N
F
O
GUIDE
Exit
USB Configuration
Zone & Room Number
Next
1. Complete the appropriate field(s) as described below. Use the Left/Right arrow keys on the
Installer Remote to navigate between each of the fields.
• Zone: Enables you to set a TV Zone # so that the TV can be configured with Installer Menu
and/or TV Setup Menu settings intended only for the assigned Zone. The Installer Menu
and/or TV Setup Menu settings may be provided in a .tlx file to be used either for Teaching
(cloning) or FTG Mode via CPU configuration. If the TV is being configured for FTG Mode via
CPU, the TV Zone # setting also allows the TV to omit channels that have been restricted in
the FTG Channel Map. To set a TV Zone, navigate to the Zone field at the left of the screen,
and use the Up/Down arrow keys to specify a TV Zone # (1–8).
• Label: Allows you to select a North, South, East, or West text label for this TV. In the Label
field, use the Up/Down arrow keys to select the applicable label.
• Room Number: Allows you to specify the number of the room in which the TV is located. In
the Room Number field, you can use the number keys on the Installer Remote to direct enter
a room number. Use the Dash key on the Installer Remote as necessary to toggle between
number and letter characters in the Room Number field. Also, you can use the Flashback key
on the Installer Remote to delete characters in this field.
2. When you are ready to continue, select the appropriate option, as follows:
• To proceed to the next EZ-Manager screen, use the arrow keys to select Next, and then
press OK on the Installer Remote. Continue to the “Configure Pro:Centric Settings” section
on the following page.
• If you wish to use a USB memory device in conjunction with the TV’s standard USB Down-
load Menu to complete the configuration, continue to “USB Configuration” on page 17.
• If you wish to use a USB memory device in conjunction with the LG Smart Install utility to
complete the configuration, see “LG Smart Install Utility” on pages 18 to 19.
14
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
EZ-Manager Wizard (Cont.)
Configure Pro:Centric Settings
Once you select “Next” from the TV Configuration Options screen,
the Searching for Pro:Centric Server screen is displayed (see
example at right), and you have the following options:
Z
EZ-Manager Wizard
4
1
3
2
Searching for Pro:Centric Server...
It may take 1 min 32 second(s).
• You can allow the EZ-Manager Wizard to proceed with a series
of automated steps to configure the TV for Pro:Centric operation
and then to look for the Pro:Centric application and maintenance
(E-Z Installation) files to download. In this case, the wizard
uses a search algorithm to determine the Data Channel and the
Pro:Centric Application Mode to set in the TV.
This step automatically searches for the Pro:Centric server.
If there is no Pro:Centric Server installed, you do not need to continue
with this procedure. Please select either ‘Exit’ or ‘Manual Pro:Centric’.
Status : Tuning channel 49
TV is now searching all of the channels for the data channel...
Back
Exit
Manual Pro:Centric
Continue with the “Automated Pro:Centric Configuration” sub-
section below.
Note: You can select the “Back” button, where
available, to check previous settings, as necessary.
• If you already know the settings (i.e., Data Channel and
Pro:Centric Application Mode) that need to be configured in
order for the TV to connect to the Pro:Centric server and/or if
the Pro:Centric server is not yet installed, you may expedite
the setup process by entering this data manually.
Continue with the “Manual Pro:Centric Configuration” subsection
on the following page.
Automated Pro:Centric Configuration
Z
EZ-Manager Wizard
4
1
3
2
Note: If the server is not yet configured on the system, use the
Pro:Centric Server was found...
It may take 2 second(s).
manual configuration option to configure the Pro:Centric operation.
The Pro:Centric data channel was found!! (Data Channel: 75, Mode: GEM)
The Download window will open in 2 second(s). You may wait or select ‘Next’.
Otherwise, if you select ‘Exit’, the Pro:Centric server settings can be retained
and used during the next download by selecting ‘Save & Exit’ in the Exit window.
Once the RF channel used by the Pro:Centric server as its data
channel is found (the Pro:Centric Server Was Found screen will be
displayed—see example at right) and the Pro:Centric Application
Mode is determined, the wizard will advance to the Processing the
Pro:Centric Configuration screen, which shows the progress of the
data downloads. Note that some steps may require a few minutes.
Status : Tuning channel 75
The Pro:Centric data channel is found!!
(Data Channel: 75, Mode: GEM)
Back
Exit
Next
EZ-Manager Wizard
If the process is successful, no further user interaction is required,
though, in some instances, where the option (for example “Next”)
is available, you may manually move forward to subsequent steps
within the wizard to speed up the process.
4
1
2
3
Processing the Pro:Centric Configuration...
Downloading the maintenance files takes several minutes.
Please wait...
20%
Retrieving files from data channel 75
Note: If, after completing the search, the TV is unable to find
a Pro:Centric server’s RF channel (while the Searching for
Pro:Centric Server screen is on display), the wizard will stop and
show a Diagnostics screen that enables you to manually return
to the previous screen (to reinitiate the configuration) or exit the
wizard.
Application files
Maintenance files
GEM app downloaded
In progress...
– Updating Configuration File
Warning - Do not remove AC power or the signal cables during these steps
EZ-Manager Wizard
1
2
3
4
EZ-Manager Configuration Complete
When the Pro:Centric Configuration is complete, an EZ-Manager
Configuration Complete screen is displayed, and after 10 seconds,
the wizard exits, and the TV turns OFF.
The TV will turn off in 3 second(s).
Installed Components
Pro:Centric Application
Maintenance Files
GEM application downloaded
LP645H_Config.tlx
Note: With the EZ-Manager Configuration Complete screen on
display, you can also manually turn off or reboot the TV. If
desired, select Turn Off or Reboot, respectively, and then press
OK on the Installer Remote.
Reboot
Turn Off
206-4232
15
Download from Www.Somanuals.com. All Manuals Search And Download.
EZ-Manager Wizard (Cont.)
Manual Pro:Centric Configuration
EZ-Manager Wizard
1. With the Searching for Pro:Centric Server screen on display,
use the arrow keys on the Installer Remote to select/highlight
the Manual Pro:Centric option at the bottom right of the
screen, and press OK.
4
1
3
2
Pro:Centric Manual Configuration
Pro:Centric Mode
GEM
1
<
>
Data Channel
0%
0%
Signal Strength
Signal Quality
In the Pro:Centric Manual Configuration screen (see example
at right), you will be able to configure the appropriate
Pro:Centric settings in the TV. Use the Up/Down arrow keys
on the Installer Remote to navigate between fields.
No signal
Back
Exit
Next
2. In the Pro:Centric Mode field, use the Left/Right arrow keys
to select the appropriate Pro:Centric Application Mode—
GEM, FLASH, or Configuration Only.
EZ-Manager Wizard
4
1
3
2
Are you sure you want to exit the wizard?
!
If you select ‘OK’ now, your settings will be lost
Note: For remote management only, select “Configuration
Only.” The TV will search for TV E-Z Installation data down-
loads; however, Pro:Centric application data will not be
downloaded, i.e., Installer Menu item 098 PRO:CENTRIC will
be set to 0.
and you will exit the setup wizard.
This window will close and you will be returned to
%
%
previous
the
page automatically in
2
seconds.
Save and Exit
OK
Cancel
Back
Exit
Next
3. In the Data Channel field, either key in or use the Left/Right
arrow keys to select the RF channel number that will be
used by the Pro:Centric server as its data channel. The Data
Channel value can be set from 1 to 135.*
EZ-Manager Wizard
4
1
2
3
Processing the Pro:Centric Configuration...
Downloading the Pro:Centric application files takes a few minutes.
Please wait...
1%
4. Once all fields are completed as required, you have two
options (see also note below):
Retrieving files from data channel 75
Application files
Maintenance files
In progress...
Pending...
• To save the data entered and exit the wizard, use the arrow
keys to select Exit and then press OK. In the subsequent
pop-up confirmation window, select Save and Exit, and then
press OK once more. The Pro:Centric application and/or E-Z
Installation data will be downloaded to the TV at a later time.
This option is useful, in particular, if the Pro:Centric server
has not yet been configured.
Warning - Do not remove AC power or the signal cables during these steps
EZ-Manager Wizard
1
2
3
4
EZ-Manager Configuration Complete
The TV will turn off in 3 second(s).
• To initiate a real-time download of Pro:Centric application
and/or E-Z Installation data, use the arrow keys to select
Next, and then press OK.
Installed Components
Pro:Centric Application
Maintenance Files
GEM application downloaded
LP645H_Config.tlx
The EZ-Manager Wizard will proceed with the remaining
Pro:Centric application and/or E-Z Installation data down-
load steps, as shown on the Processing the Pro:Centric
Configuration screen.
Reboot
Turn Off
Note: Pro:Centric server data must be present on the RF channel selected as the
TV’s Data Channel in order for you to select “Next” (you will see a “Data Channel
found” message below the signal strength indicator).
When the Pro:Centric configuration is complete, an EZ-Manager Configuration Complete
screen is displayed, and after 10 seconds, the wizard exits, and the TV turns OFF.
Note: With the EZ-Manager Configuration Complete screen on display, you also have
the option to manually turn off or reboot the TV. If desired, select Turn Off or Reboot,
respectively, and then press OK on the Installer Remote.
* PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.
16
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
EZ-Manager Wizard (Cont.)
USB Configuration
Before you begin, note the following:
• Each of these functions requires that you have the appropriate file(s) loaded on a USB memory
device. If you wish to perform a software upgrade from the USB Download Menu, the software
upgrade files must be stored in a folder named “LG_DTV” in the root directory of the USB memory
device. Cloning (.tll/.tlx) or FTG Configuration (.tlx) files should simply be stored in the root directory
of the USB device.
• If you intend to use the TV Zoning feature on this TV, make sure to assign the TV Zone # in the
EZ-Manager’s Zone, Label, and Room Number screen BEFORE continuing with USB Configuration.
See “TV Configuration Options” on page 13 for further information.
• Refer to “Creating an FTG Configuration File using the FTG File Manager” on pages 45 to 46 for
information on creating an FTG Configuration (.tlx) file that can be used for FTG Mode via CPU
configuration. Also note that to configure the TV for FTG Mode via CPU, the FTG Configuration file
must contain an FTG Channel Map. If it does not, any Installer Menu and/or TV setup menu settings
contained in the file will be transferred to the TV (as with typical cloning); however, the TV will remain
in Pass-through Mode and will not be configured for FTG Mode via CPU.
• Refer to “Custom Master TV Setup” on pages 29 to 32, for information on creating a .tll file that can
be used for cloning.
• Ensure the USB device to be used has been formatted with FAT format.
With either the TV Configuration Options or the Zone, Label, and Room Number screen on
display, proceed as follows to configure the TV using the USB memory device.
1. Insert the USB memory device that contains the appropriate file(s) into the TV’s USB IN port.
2. Use the arrow keys to select USB Configuration, and then press OK on the Installer Remote.
You will be redirected to the TV’s USB Download Menu. For further information on USB
Download Menu functions, refer to the appropriate section(s) in this document.
USB Download Menu
Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
Teach To TV (TLX)
Previous
OK
Note: With the USB Download Menu on display, you can press on the Installer Remote at any
time to return to the EZ-Manager Wizard.
Note: If you perform a software upgrade from the USB Download Menu, the TV will complete
the upgrade and then reboot. Upon restart, the TV will display the EZ-Manager TV Configuration
Options screen. If desired, you can re-access the USB Download Menu (to perform additional
functions), proceed with configuration via the wizard, or exit the wizard.
Note: (FTG configuration only) When configuration is complete, the TV tunes according to the
Start Channel setting in the Installer Menu. If a Start Channel is specified, the TV will tune to that
channel; otherwise, the TV will tune to the lowest logical channel in the FTG Channel Map.
3. Remove the USB memory device, and verify that the appropriate configuration is resident on the
TV.
206-4232
17
Download from Www.Somanuals.com. All Manuals Search And Download.
LG Smart Install Utility
LG Smart Install is a new utility that enables you to configure the TV or update multiple TV
configuration elements at one time using files loaded on a USB memory device. You may use LG
Smart Install to download any one or all of the following to a TV: an FTG Configuration (.tlx) file, a .tlx
file for cloning purposes (no Channel Map), a TV or PTC software update, a splash screen image.
Before you begin, note the following:
• All files must be stored in a folder named “LGSMARTINSTALL” in the root directory of the USB
memory device. Also, ensure the USB device has been formatted with FAT format.
• Cloning using a .tll file is only available from the TV’s USB Download Menu.
• Refer to “Creating an FTG Configuration File using the FTG File Manager” on pages 45 to 46 for
information on creating an FTG Configuration (.tlx) file that can be used for FTG Mode via CPU
configuration. Also note that to configure a TV that is currently in Pass-through Mode for FTG
Mode via CPU, the FTG Configuration file must contain an FTG Channel Map. If it does not, any
Installer Menu and/or TV setup menu settings contained in the file will be transferred to the TV
(as with typical cloning); however, the TV will remain in Pass-through Mode and will not be con-
figured for FTG Mode via CPU.
• Refer to Reference section, “Downloading a Splash Screen using a USB Memory Device,” for
splash screen image guidelines.
Caution: Do not unplug the TV power cord or remove the USB memory device
during a data download, as doing so may cause the TV to malfunction or harm the
USB device, respectively.
The following procedure describes how to use the LG Smart Install utility.
1. If it is not ON already, turn ON the TV.
The next step to access the LG Smart Install utility depends on whether the EZ-Manager Wizard
appears on the screen when you turn ON the TV:
• If the wizard is displayed, you can insert the USB memory device that contains the appropriate
file(s) into the TV’s USB IN port at any time to initiate the LG Smart Install utility.
The LG Smart Install utility Integrated USB Downloading screen will be displayed (see example
on following page). Go to step 3.
• If the wizard is not displayed, insert the USB memory device that contains the appropriate
file(s) into the TV’s USB IN port, and continue with step 2.
Note: If you intend to use the TV Zoning feature for location-specific configuration
purposes, make sure to assign the TV Zone # in the TV BEFORE continuing with LG
Smart Install. If the EZ-Manager is currently active, see “TV Configuration Options”
on page 13 for further information. If the TV is currently in Pass-through Mode, see
Reference section, “Using the TV Zoning Feature,” for further information.
(Continued on next page)
18
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
LG Smart Install Utility (Cont.)
(Continued from previous page)
2. To access the LG Smart Install utility Integrated USB Down-
loading screen from the TV menus:
USB LG Smart Install Utility
Integrated USB Downloading
Select the configuration file(s) to download, and then select ‘Next’.
• Press MENU SETTINGS on the Installer Remote to display
the TV setup menus (TV is in Pass-through Mode) or the
Function Menu (TV is not in Pass-through Mode).
xxLP645H-UA00001.TLX
Splash-Image-1360-x-768.jpg
xxLP645H_v3.35.00_usb.epk
• Use the arrow navigation keys to select/highlight either the
Option menu icon from the TV setup menus or the Lock
menu icon from the Function Menu. Then, press the number
“7” key a total of seven times.
Previous
Next
USB LG Smart Install Utility
3. The Integrated USB Downloading screen contains a listing of
the files stored in the LGSMARTINSTALL folder on the USB
device.
Downloading Data...
Warning - Do not remove the USB device during this process
The utility will only ever allow you to select one of each file
type for downloading. For example, if there are two .tlx files
in the LGSMARTINSTALL folder, you will only be able to
select one of those two files. By default, the first instance of
each file type listed on the screen is selected. To select or
de-select a file, respectively, use the Up/Down arrows on the
Installer Remote to highlight the filename, and press OK to
add or remove the checkmark at the left of the filename.
Maintenance File
File Name :
Complete
Ready
xxLP645H-UA00001.TLX
Boot Logo File
File Name :
Splash-Image-1360-x-768.jpg
xxLP645H_v3.35.00_usb.epk
Software File (CPU)
File Name :
Ready
USB LG Smart Install Utility
Complete
The TV will reboot in 2 second(s).
Note: Use the arrow keys on the Installer Remote to select
Previous and press OK, as necessary, to exit the LG Smart
Install utility. If you accessed the utility via the EZ-Manager
Wizard, you will be returned to the last screen on display
before you inserted the USB device. If you accessed the
utility via the TV menus, you will be returned to TV viewing.
Installed Components
Maintenance File :
Boot Logo File :
xxLP645H-UA00001.TLX
Splash-Image-1360-x-768.jpg
xxLP645H_v3.35.00_usb.epk
Software File (CPU) :
4. When you are ready to continue, use the arrow keys on the
Installer Remote to select Next, and then press OK.
The TV will show download progress in a new window. Do
NOT remove the USB device until downloading is complete.
When the download is complete, the TV will briefly display an
overview of the results in a “Complete” window and then
return to TV viewing or reboot (the latter if software has just
been downloaded).
5. Remove the USB memory device, and verify that the
appropriate configuration is resident on the TV.
Note: (FTG configuration only) When configuration is complete,
the TV tunes according to the Start Channel setting in the
Installer Menu. If a Start Channel is specified, the TV will tune
to that channel; otherwise, the TV will tune to the lowest logical
channel in the FTG Channel Map.
206-4232
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu
Use the Installer Menu to set up, change, or view operational settings. This section describes
how to access, use, and exit the Installer Menu from the TV itself; however, you should also refer
to the Installer Menu descriptions in this document if you are configuring the TV using LG’s FTG
configuration software.
Refer to the table on pages 22 and 23 for brief descriptions of Installer Menu items. More detailed
descriptions follow the table listing.
Accessing the Installer Menu
1. Turn ON the TV.
If the EZ-Manager Wizard appears on the screen when you turn ON the TV, use the arrow
keys on the Installer Remote to select Exit from the Welcome screen and press OK. In the
confirmation pop-up window, select OK, and then press OK once more on the Installer Remote
to exit the wizard.
2. Using an Installer Remote, press MENU SETTINGS repeatedly until the on-screen display of
the TV setup menus (if the TV is in Pass-through Mode) or the Function Menu (if the TV is not
in Pass-through Mode) no longer toggles, and then press the Installer Menu entry sequence
(e.g., 9-8-7-6) + OK to access the Installer Menu.
Note: The default Installer Menu entry sequence is “9876”; however, if Installer Menu item 000
INSTALLER SEQUENCE has been modified, the entry sequence may be one of three additional
options. See Installer Menu detailed descriptions for further information.
The Installer Menu opens with item 000 INSTALLER SEQ 000.
xxLP645H PTC INSTALLER MENU
CPU-CTV
000 INSTALLER SEQ
000
UPN 000-000-000-000
PTC V1.00.022
ASIC D279
CPU V3.35.00
Typical Installer Menu
Note: The Installer Menu header will vary depending on the TV you are setting up.
Note: If the password (entry sequence) is not entered or registered correctly, you will see the
message “ENTER PASSWORD 0000” at the top of the screen instead of the Installer Menu
header. Once you re-enter the correct password (e.g., press 9-8-7-6 + OK), the Installer Menu will
display.
Note: If the TV is not in Pass-through Mode, the Installer Menu is accessible as read-only. Also,
the TV Zone # will be indicated in the Installer Menu header under the configuration mode indicator
described on the following page.
20
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
As part of the Installer Menu header (in all modes), two 3-character acronyms are displayed to indicate
the TV’s current configuration mode. The table below lists all possible mode identifiers for these TV
models.
Acronym
Description
CPU-CTV
CPU-FTG
CPU-P:C
EBL-FTG
EBL-LNT
MPI-EXT
PTC-CTV
Pass-through Mode with Channel Map in CPU
FTG Mode via CPU
Application Tuning Mode via CPU
FTG Mode via EBL
LodgeNet PPV Mode
External MPI Control
Pass-through Mode with Channel Map in PTC
Using the Installer Menu
Refer to the table starting on the next page for an overview of the available Installer Menu items,
including their item numbers, functions, value ranges, and default values.
Installer Menu items not relevant to these TV models are not present in the Installer Menu; therefore,
some numbers are missing. For example, item 006 will not appear. In addition, items that are
dependent on other Installer Menu item settings will not be initially accessible. For example, item 046
STRT AUX SRCE will not display in the Installer Menu unless item 004 STRT CHANNEL is set to 0.
Navigation within the Installer Menu
Use the Up/Down arrow keys on the Installer Remote to sequence through the available menu items,
or access an item directly by keying in the item number and then pressing MENU SETTINGS. For
example, to access the SLEEP TIMER option, which is item 015, press 0-1-5 + MENU SETTINGS.
Changing Installer Menu Settings
To change an Installer Menu item value, use the Left/Right arrow keys on the Installer Remote, or
enter a valid value directly. To save the new setting, press OK, or use the Up/Down arrow keys to
navigate to a new Installer Menu item if you have additional items to edit. Note that invalid values will
not be saved.
Exiting the Installer Menu and Activating Settings
After you have adjusted all required Installer Menu item settings, press OK once on the Installer
Remote to save your changes; then, press OK again to exit the Installer Menu. Any changes you
make will be stored in non-volatile memory.
Note: Each time you exit the Installer Menu in Pass-through Mode, all V-Chip (Parental Control)
settings in the TV are reset to their default values; that is, the Lock System, if previously enabled
from the Lock setup menu, will now be disabled, and the individual Parental Control settings will be
restored to default values.
206-4232
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
Installer Menu Items 000 through 075
Menu
Function
Value Range
Default Value
Brief Description of Function
Item
000
001
002
003
INSTALLER SEQ
POWER MANAGE
AC ON
0 ~ 3
0 ~ 7
0 / 1
0
0
0
1
Leave default set to 0.
Sets number of hours of no activity before automatic shutoff.
Set to 1 to enable TV to turn ON when AC power is applied.
Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC
BAND/AFC
0 ~ 3
Channel tuned when TV is turned ON. (Set to 255 to tune to channel
tuned before TV turned OFF.)
004
005
007
STRT CHANNEL
CHAN LOCK
0 ~ 127, 255
0 / 1
255
0
If set to 1, cannot tune from current channel.
Volume level when TV is turned ON. (Set to 255 to use volume level
before TV turned OFF.)
STRT VOLUME
0 ~ 63, 255
255
008
009
010
011
015
016
017
020
021
022
023
028
029
030
031
032
MIN VOLUME
MAX VOLUME
MUTE DISABLE
KEY DEFEAT
SLEEP TIMER
EN TIMER
0 ~ 63
0 ~ 63
0 / 1
0
63
0
Sets minimum allowable volume setting.
Sets maximum allowable volume setting.
Set to 1 to disable Mute Function.
0 / 1
0
If set to 1, menu navigation buttons on display panel are not functional.
Set to 1 to enable Sleep Timer.
0 / 1
1
0 / 1
0
Set to 1 to enable On/Off Timers.
ALARM
0 / 1
1
Set to 1 to enable Alarm.
FEATURE LEVEL
V-CHIP
0, 16 ~ 24
0 / 1
0
Determines an additional IR code scheme to which the TV will respond.
Set to 1 to enable V-Chip (Parental Control) functions.
Sets number of V-Chip blocking hours.
1
MAX BLK HRS
CAPTION LOCK
CH. OVERIDE
OLD OCV
0 ~ 99
0 / 1
12
0
Set to 1 to retain caption setting set before TV turned OFF.
If set to 0, limits direct access to favorite channels.
Set to 1 to change MPI operation to OCV.
If set to 1, enables ACK feature of MPI.
0 / 1
1
0 / 1
0
ACK MASK
0 / 1
0
POLL RATE
20 ~ 169
186 ~ 227
94
207
Selects poll rate for MPI.
TIMING PULSE
Sets baud rate for MPI.
Set to 0 to disable HDMI 1. Set to 1 (DTV Mode) or 2 (PC Mode), as
applicable, to enable HDMI 1.
035
HDMI1 ENABLE
0 ~ 2
1
039
041
REAR AUX EN.
SIMPLINK EN
0 / 1
1
0
Set to 1 to enable display panel Video 1 input jack.
0 ~ 3
Determines the status of the SIMPLINK feature. (See detailed descriptions.)
Determines the Aux inputs for which auto-sensing is enabled. (See detailed
descriptions.)
042
046
047
AUTO INPUTS
STRT AUX SRCE
AUX STATUS
0 ~ 255
1, 3 ~ 5, 7, 255
0 / 1
0
7
0
Sets the starting Aux source (if item 004 STRT CHANNEL is set to 0).
Set to 1 for MPI Aux source to be reported as a channel number instead of
Channel 0.
053
069
070
071
DIS. CH-TIME
EN. CH-T COL.
FOR. CH-TIME
BCK. CH-TIME
0 / 1
0 / 1
0 ~ 7
0 ~ 7
0
1
2
2
Set to 1 to disable Channel-Time display.
Set to 1 to enable custom color for the Channel-Time display.
Chooses custom foreground color for the Channel-Time display.
Chooses custom background color for the Channel-Time display.
If set to 1 and item 028 CH. OVERIDE is set to 0, “NOT AVAILABLE” message
is displayed if user direct tunes a channel that is not in the favorite channel list.
073
075
CH NOT AVBLE
REVERT CH
0 / 1
0 / 1
0
0
If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel.
22
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
Installer Menu Items 078 through 122
Menu
Function
Value Range
Default Value
Brief Description of Function
Item
078
079
080
081
082
UPN MSB
0 ~ 255
0 ~ 255
0 ~ 255
0 ~ 255
0 / 1
0
0
0
0
1
User programmable number, most significant byte.
User programmable number, most significant byte - 1.
User programmable number, most significant byte - 2.
User programmable number, least significant byte.
Enforces rigid MPI checksum.
UPN MSB-1
UPN MSB-2
UPN LSB
CHKSM ERROR
Relaxes MPI timing to be compatible with PC-based Windows-
controlled systems.
083
084
087
HANDSHK TIME
PERMANENT BLK
REAR RGB EN.
0 ~ 5
0 / 1
5
0
1
Removes block hours setting for Parental Control and makes block permanent.
Dependent on item 093 RJP AVAILABLE setting. Set to 0 to disable RGB input.
Set to 1 to enable RGB input. Set to 17 for Auto Configure.
0
,
1, 17
088
090
EN NOISE MUTE
KEY LOCK
0 / 1
0 / 1
1
0
If set to 1, audio is muted if no signal is present.
If set to 1, display panel buttons are locked. IR is still functional.
Set to 0 to disable HDMI 2. Set to 1 (DTV Mode) or 2 (PC Mode), as
applicable, to enable HDMI 2.
091
092
093
HDMI2 ENABLE
HDMI3 ENABLE
RJP AVAILABLE
0 ~ 2
0 ~ 2
1
1
0
Set to 0 to disable HDMI 3. Set to 1 (DTV Mode) or 2 (PC Mode), as
applicable, to enable HDMI 3.
Set to 0 to disable. Set to 1, 2, 5, or 6 for HDMI or DVI Mode. (See
detailed descriptions.)
0, 1, 2, 5, 6
Set to 0 to disable feature on Function Menu. Set to 1 to enable feature on
Function Menu.
094
096
097
SAP MENU EN
DEF. ASP. RATIO
AUDIO OUTPUT
0 / 1
0 ~ 4
0 ~ 9
1
2
7
Sets default aspect ratio at power up. See detailed descriptions and item 106.
Set as required in accordance with external audio equipment connected to the
TV. See detailed descriptions.
Set to 0 to disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2 for
GEM (Java Application) Mode.
098
PRO:CENTRIC
0 ~ 2
0
099
102
103
104
BACK LIGHTING
ATSC BAND
1 ~ 200, 255
0 ~ 4
255
4
Sets the level of the TV picture back lighting. (See detailed descriptions.)
Selects ATSC band.
ATSC TUNE MODE
START MINOR CH
0 / 1
1
Set to 1 (default) for Physical Channel scan. Set to 0 for Virtual Channel scan.
Selects Minor Start Channel. Set to 0 for NTSC.
0 ~ 255
0
To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on
power cycle.
106
ASP RATIO LOCK
0 / 1
0
116
117
VIDEO MUTE EN
FACT DEFAULT
0 / 1
0 / 1
0
0
Set to 0 for Normal. Set to 1 for Blank.
Set to 0 for Normal. Set to 1 to load presets for all Installer Menu settings.
Determines the powered status of the embedded b-LAN module and the
118
119
POWER SAVINGS
DATA CHANNEL
1, 3, 7
3
GAME CONTROL/MPI port. (See detailed descriptions.)
Set to 0 to disable. Set from 1 to 135 to match the RF channel number used by
the Pro:Centric server as its data channel. Set to 255 to use Auto Search to
find the Pro:Centric RF channel. (See detailed descriptions.)
0 ~ 135, 255
255
Sets the hour for Wake On RF. The value “128” is displayed as “OFF.” Directly
entering 128 turns the Wake On RF feature OFF.
121
122
P:C RF WAKE HR
P:C RF WAKE MN
0 ~ 23, 128
0 ~ 59
128
0
Sets the minute for Wake On RF.
Caution: Installer Menu settings may affect options available
from the TV setup menus or the Function Menu.
206-4232
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
Detailed Descriptions of Installer Menu Items
NOTE: For items 007, 008, and 009
000 - INSTALLER SEQUENCE
For legacy reasons, the scale used is 0 – 63. The PTC software
will translate this to the 0 – 100 scale used by the TV.
Specifies entry sequence to the Installer Menu.
0 = 9876
2 = 1478
1 = 4321
3 = 3698
To translate a TV volume level to the Installer Menu value, use
the following formula:
001 - POWER MANAGE (Power Management)
Installer Value = TV Value x 63
100
Determines hours of no activity before automatic shutoff. The
Power Management function is for saving energy. If set to 0,
Power Management is Off. Settings range from 0 ~ 7, with 1 ~ 7
representing the hours that the unit will remain ON, unless there
has been activity from either the control panel or remote control.
Enter only the whole number (disregard fractions).
007 - STRT VOLUME (Start Volume)
This function allows the Installer to determine the initial volume
level setting when the TV is turned ON. This feature is useful for
an in-house information channel, since the TV will always select
that volume level when it is turned ON. The range of values is 0
to 63, 255. If set to 255, the last volume level before the TV was
turned OFF will be the current volume level when the TV is turned
ON again.
002 - AC ON (AC Power Switchable)
If set to 1, this allows the TV to turn ON when AC power is applied.
Pressing the POWER button is not necessary. This is desirable if
the TV is plugged into a switched AC outlet (i.e., a set-top box). Set
to 0 (default) for standard TV turn ON/OFF operation.
Note: If set to 1, the TV does not respond to ON/OFF commands
from either the remote or the display panel, and the SLEEP TIMER
is also nonfunctional.
008 - MIN VOLUME (Minimum Volume)
This function determines the minimum volume level allowable
with the Volume (VOL) Up/Down control. In this way, for example,
someone cannot set the volume too low to hear. The value range
is from 0 to 63. The factory default is 0, which provides the full
range of volume control, if item 009 MAX VOLUME is set to 63. It
is recommended to set the same value on every TV.
003 - BAND/AFC (Band/Automatic Frequency Control)
There are four possible settings for this option:
0 = Broadcast
2 = HRC
1 = CATV (default)
3 = IRC
If some channels were not found by Auto Tuning (Channel
Search), select the appropriate Band setting here, and add the
channels using the Channel Edit option in the Channel Menu.
Note: The minimum volume level cannot have a value setting
higher than the maximum volume level (described below).
004 - STRT CHANNEL (Start Channel)
009 - MAX VOLUME (Maximum Volume)
If active, this function allows you to determine the initial Major
Start Channel number when the TV is turned ON. This feature is
useful for an in-house information channel, since the TV would
always select that channel when it is turned ON. If set to 255,
the last channel tuned before the TV was turned OFF will be the
channel tuned when the TV is turned ON again.
This function determines the maximum volume level allowable
with the Volume (VOL) Up/Down control. In this way, for example,
someone cannot set the volume level high enough to disturb
others. The value range is 0 to 63, with 63 as the default, which
gives the user the full range of volume control, if item 008 MIN
VOLUME is set at 0. It is recommended to set the same value on
every TV.
0 = Aux
127 = Map to Major CH 4
255 = Last Channel
1 ~ 125 = Major CH #
126 = Map to Major CH 3
Note: The maximum volume level cannot have a value setting
lower than the minimum volume level (described above).
Note: For a digital Start Channel, always remember to set item
104 to the Minor Start Channel number.
010 - MUTE DISABLE
Enables or disables sound mute function. If set to 1, sound cannot
be muted. If set to 0, sound can be muted.
Note: 126 and 127 are mapped only in LodgeNet PPV Mode.
005 - CHAN LOCK (Channel Lock)
011 - KEY DEFEAT
Channel Lock is ideal if the system must always be on the same
channel. Changing channels with the Channel Up/Down or keypad
numbers is impossible. Channel Lock is inactive if set to 0 (default).
If set to 1, Key Defeat is enabled, which means that end users
cannot access or navigate within the on-screen menu(s) from the
display panel, i.e., SETTINGS, OK, and menu navigation buttons
on the display panel will not function. Set to 0 to disable Key
Defeat. Note that all IR features remain functional regardless of
this setting.
Generally, this feature is used in connection with item 004 STRT
CHANNEL where the Start Channel may, for example, be set to
3 or 4. If the Start Channel is 3, then the TV will remain locked on
channel 3.
24
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
015 - SLEEP TIMER
030 - ACK MASK
If set to 1, the Sleep Timer feature may be used. If set to 0, the
Sleep Timer is not available.
MPI Communication Parameter. When set to 1, enables ACK
feature of MPI.
016 - EN TIMER (Enable On/Off Timers)
031 - POLL RATE
If set to 1, the Timer function is available to the end user and
enabled continuously. Set to 0 to disable On/Off timers.
MPI Communication Parameter. Selects poll rate for MPI. Step size
of 16 ms. Changing from default may affect communication via MPI.
Note: The TV clock must be set in order for timers to be used.
032 - TIMING PULSE
MPI Communication Parameter. Sets baud rate for MPI. Step size
of 4.3 uS. Changing from default may affect communication via
MPI.
017 - ALARM
Gives the installer the option of making the Alarm function available
to the end user. If set to 1, the Alarm function is available to the end
user. Set to 0 to disable the Alarm function.
035 - HDMI1 ENABLE
Note: The TV clock must be set before the Alarm function will work.
Set to 1 to enable HDMI 1 input in DTV Mode. Set to 2 to enable
HDMI 1 input in PC Mode. Set to 0 to disable display panel HDMI
1 input.
020 - FEATURE LEVEL
Determines an additional IR code scheme to which the TV will
respond, allowing for the use of unique IR codes based on “bed
number” in a multi-TV single room installation. First determine the
IR mode; then select the bed number.
Note: This setting is ignored if item 093 RJP AVAILABLE is set to 1.
039 - REAR AUX EN. (Rear Aux Enable)
Set to 1 to enable display panel rear Aux (Video 1) input. Set to 0
to disable display panel rear Aux (Video 1) input.
Values
0
IR Mode
Bed #
N/A
Disabled
041 - SIMPLINK EN
16 – 24
Multi-code Remote
1 – 9
Set to 0 to disable the SIMPLINK feature. Set to 1 to enable
SIMPLINK functionality without enabling remote control access to
the SIMPLINK Menu. Set to 2 to enable both SIMPLINK function-
ality and SIMPLINK Menu access, though note that the Speaker
menu option will be inaccessible/grayed out. Set to 3 to enable
all aspects of SIMPLINK feature and SIMPLINK Menu. If a home
theater device is connected to the TV, users can select either the
TV or HT (home theater) speaker.
Note: For further information, see documentation for the accessory
package that includes the multi-code remote.
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental Control) and have it available
to the end user to filter and control or otherwise restrict program-
ming content that can appear. Set to 0 to turn the V-Chip feature
Off (not available to user); no programming restrictions can be set.
Note: When both this item and item 042 AUTO INPUTS are
enabled in the Installer Menu, HDMI inputs will be detected by
SIMPLINK, but the Auto Input(s) Sensing Feature will not function.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum V-Chip (Parental Control)
block hours. Default setting is for 12 blocking hours.
042 - AUTO INPUTS
Note: This item is not available in the Installer Menu when item
084 PERMANENT BLK is set to 1.
Determines the Aux inputs for which auto-sensing is enabled. Set
to 0 to disable auto-sensing for all available inputs. Set to 255 to
enable auto-sensing for all available inputs. For information on
options for individual input settings, refer to Reference section,
“Auto Input(s) Sensing Feature.”
023 - CAPTION LOCK
If set to 0, captions are OFF when the TV is turned ON. Set to 1 to
use the caption setting configured before the TV was turned OFF
when the TV is turned ON.
Note: In order for auto-sensing to be enabled for an input, that
input must also be enabled in the Installer Menu. For example, to
enable auto-sensing for HDMI 1, item 035 HDMI1 ENABLE must
also be set to 1 or 2. Also, see note above regarding TV operation
when both this item and item 041 SIMPLINK EN are enabled.
028 - CH. OVERIDE (Channel Override)
If set to 1, the user can select channels with either Channel Up/
Down or by direct keypad entry. If set to 0, only those channels
that are active in the TV’s memory can be selected.
Note: When this item is enabled in the Installer Menu, item 093
RJP AVAILABLE is automatically set to 0.
029 - OLD OCV (On Command Video™)
Set to 1 to remap the PTC’s direct tune channels for Aux inputs
from 13x to 9x. This allows 2-digit only tuning systems (i.e., legacy
OCV) to direct tune Aux inputs. See also Reference section, “TV
Aux Input Configuration.”
206-4232
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
046 - STRT AUX SRCE (Start Aux Source)
078 - UPN MSB (UPN Most Significant Byte)
Sets the starting Aux source. When turned ON, the TV will tune to
starting Aux source if item 004 STRT CHANNEL is set to 0.
User programmable number, most significant byte readable by
MPI command. Note: Not linked to serial number.
1 = Video 1
3 = HDMI 1
4 = RGB
5 = HDMI 2
7 = HDMI 3
255 = Last Aux
079 - UPN MSB-1 (UPN Most Significant Byte-1)
User programmable number, most significant byte-1 readable by
MPI command. Note: Not linked to serial number.
Note: Above is applicable only if all Aux sources are enabled.
Note: This item is not available in the Installer Menu unless item
004 STRT CHANNEL is set to 0.
080 - UPN MSB-2 (UPN Most Significant Byte-2)
User programmable number, most significant byte-2 readable by
MPI command. Note: Not linked to serial number.
047 - AUX STATUS
Set to 1 for MPI Aux source to be reported as a channel number
instead of channel 0. Set to 0 to disable Aux identification change.
Controls MPI status channel response for Aux inputs.
081 - UPN LSB (UPN Least Significant Byte)
User programmable number, least significant byte readable by
MPI command. Note: Not linked to serial number.
053 - DIS. CH-TIME (Disable Channel-Time)
Set to 1 to disable the Channel-Time display; Channel-Time display
will not appear. Set to 0 to enable the Channel-Time display.
082 - CHKSM ERROR (Checksum Error)
Enforces rigid MPI checksum validation. Set to 1 for validation.
Set to 0 to disable (does not check checksum on MPI async port).
SPI is always checked.
069 - EN. CH-T COL. (Enable Channel-Time Custom Color)
Set to 1 to enable custom color for the Channel-Time display. Set
to 0 to disable custom color for the Channel-Time display.
083 - HANDSHK TIME (Handshake Time)
Adds an additional delay to the handshake time which is 64 msec,
thus relaxing MPI timing requirements to be compatible with PC-
based Windows controlled systems. Range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time].)
070 - FOR. CH-TIME (Channel-Time Display Foreground Color)
Set according to Color Chart:
0 = Black
1 = Blue
3 = Cyan
4 = Red
6 = Yellow
7 = White
084 - PERMANENT BLK (Permanent Block)
2 = Green
5 = Violet
Allows Lock (Parental Control) blocking schemes to be permanent
by disabling the blocking hours function. Set to 1 to install Parental
Control restrictions permanently. Set to 0 for user-specified hours
control of blocking schemes.
Note: If foreground color and background color are the same, the
menu background will be transparent.
Note: Applies only to “Channel Not Available” message if item
073 CH NOT AVBLE is set to 1 (enabled). Also, items 070 FOR.
CH-TIME and 071 BCK. CH-TIME are not available in the Installer
Menu when item 069 EN. CH-T COL. is set to 0.
087 - REAR RGB EN. (Rear RGB Enable)
Controls access to rear RGB input on TV. Set to 0 to disable RGB
input. Set to 1 to enable RGB input. Set to 17 to initiate a one-
time automatic configuration after an AC power cycle; otherwise,
automatic adjustment will be performed each time the RGB input
is accessed.
071 - BCK. CH-TIME (Channel-Time Display Background Color)
See description for item 070 FOR. CH-TIME above. The color
chart is the same for both items.
088 - EN NOISE MUTE (Enable Noise Mute)
If set to 1, audio mutes if no signal is present.
073 - CH NOT AVBLE (Channel Not Available)
If set to 1 and item 028 CH. OVERIDE is set to 0, a “NOT AVAIL-
ABLE” message is displayed when a user direct tunes a channel
that is not in the channel scan list available in memory.
090 - KEY LOCK
If set to 1, Key Lock is enabled, which means that all display panel
buttons will be locked, i.e., non-functional. Set to 0 to disable Key
Lock. Note that all IR features remain functional regardless of this
setting.
Note: This item is not available in the Installer Menu when item
028 CH. OVERIDE is set to 1.
075 - REVERT CH (Revert to Start Channel)
If set to 1 and loss of MPI communication occurs, TV automatically
tunes to the specified Start Channel.
091 - HDMI2 ENABLE
Set to 1 to enable HDMI 2 input in DTV Mode. Set to 2 to enable
HDMI 2 input in PC Mode. Set to 0 to disable display panel HDMI
2 input.
Note: This item is not available in the Installer Menu when item
004 STRT CHANNEL is set to 255.
26
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
092 - HDMI3 ENABLE
097 - AUDIO OUTPUT
Set to 1 to enable HDMI 3 input in DTV Mode. Set to 2 to enable
HDMI 3 input in PC Mode. Set to 0 to disable display panel HDMI
3 input.
Determines availability and signal type/level (fixed speaker,
variable speaker, or fixed line level [amplifier]) of the audio output
to be used by external audio equipment connected to the Speaker
Out jack on the TV. Set to 0 to disable audio output. Otherwise,
see the table below and set as required in accordance with audio
equipment.
093 - RJP AVAILABLE (Remote Jack Pack Available)
• 0 = Remote jack pack is not available or disabled.
• 1 = Legacy Model RJPs: HDMI Mode
Value
Status
Enables RJP feature for use with full cable bundle models. In
this mode, when an HDMI source is connected to the RJP, both
digital video and audio are expected via the HDMI cable. If no
digital audio is present, no audio will be heard.
Speaker Output
1
2
3
4
5
6
7
8
9
Fixed 0.01 Watts
Fixed 0.03 Watts
Fixed 0.05 Watts
Fixed 0.10 Watts
Fixed 0.20 Watts
Fixed 0.50 Watts
Fixed 1.00 Watt (default)
Control with volume
• 2 = Legacy Model RJPs: DVI Mode
Enables RJP feature for use with full cable bundle models. In
this mode, when an HDMI/DVI source is connected to the RJP,
only digital video is expected via the HDMI cable. Analog audio
is provided via a separate cable, from the source, connected to
an RJP AUDIO IN. If no analog audio cable is connected, tuner
audio will be heard.
Line Output
Fixed line level (typically 400 mVrms ±
100 mVrms @10KΩ) output
• 5 = Scaler Model RJPs: HDMI Mode
Enables RJP feature for use with reduced cable bundle models.
In this mode, when an HDMI source is connected to the RJP,
both digital video and audio are expected via the HDMI cable. If
no digital audio is present, no audio will be heard.
See also Reference section, “External Stereo Speaker Setup.”
098 - PRO:CENTRIC
Selects the Pro:Centric Application Mode. Set to 0 (default) to
disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2
for GEM (Java Application) Mode.
• 6 = Scaler Model RJPs: DVI Mode
Enables RJP feature for use with reduced cable bundle models.
In this mode, when an HDMI/DVI source is connected to the RJP,
only digital video is expected via the HDMI cable. Analog audio
is provided via separate cable, from the source, connected to
an RJP AUDIO IN. If no analog audio cable is connected, tuner
audio will be heard.
The TV must be turned OFF for a few seconds to initiate the
Pro:Centric application download. When it is turned OFF for a
second time, the TV will load the Pro:Centric application.
Note: This item is not available in the Installer Menu when item
119 DATA CHANNEL is set to 0.
Note: See also Reference section, “RJP Model List & Input Auto-
sensing Hierarchy.” Settings 1, 2, 5, and 6 allow the lodge staff to
customize each TV’s RJP setup based on customer requirements.
099 - BACK LIGHTING
Sets the TV screen brightness at power up. Default setting is 255.
Note: When this item is enabled in the Installer Menu, item 042
AUTO INPUTS is automatically set to 0.
• 1 - 100 Static Back Lighting
(1 = Dimmest picture, 100 = Brightest picture)
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable SAP feature on Function Menu, if Function
Menu is available (i.e., TV is not in Pass-through Mode). Set to
0 to disable SAP feature on Function Menu, if Function Menu is
available.
• 101 - 200 Dynamic Back Lighting
(101 = Dimmest picture, 200 = Brightest picture)
If set between 101 and 200, the TV automatically controls back
lighting depending upon the picture level of the current program. If
set to 255, back lighting is controlled via the Picture settings in the
TV’s setup menus.
096 - DEF. ASP. RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up.
102 - ATSC BAND
Sets up TV to receive different types of incoming signals:
0 = Broadcast, 1 = CATV, 2 = HRC, 3 = IRC, 4 = Same as NTSC.
• Set to 0 for Set By System.
• Set to 1 for 4:3.
• Set to 2 for 16:9 (Factory Default).
• Set to 3 for Just Scan.
• Set to 4 for Zoom.
103 - ATSC TUNE MODE
Sets ATSC tuning mode. Default set to 1 for Physical Channel
scan. Set to 0 for Virtual Channel scan.
Note: This item is not available in the Installer Menu unless item
106 ASP RATIO LOCK is set to 0.
206-4232
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer Menu (Cont.)
104 - START MINOR CHANNEL
For TVs in Pass-through Mode or FTG Mode via CPU, if this item
is left at its default value (255), the TV’s Data Channel Auto Search
feature will be enabled (see additional information below).
Sets Minor Start Channel number at power up. 0 = NTSC. If not
0, number selected is the digital channel’s Minor Start Channel
number.
Note: The Data Channel Auto Search feature is not available
when the TV’s EBL is in FTG Mode. If the DATA CHANNEL value
is 255 when the TV is configured for FTG Mode via EBL, DATA
CHANNEL is defaulted to 0.
Note: This item is not available in the Installer Menu when item
004 STRT CHANNEL is set to 0 or 255.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power off. Set to 0 to
retain default aspect ratio with power off. See item 096 DEF. ASP.
RATIO above.
Data Channel Auto Search feature: When this item is set to 255
(default), once every 24 hours, the TV will initiate a search of 10
predefined channels (10, 20, 30, ... 100) and then, if necessary,
perform a complete search of the RF channels (1 to 135) in an
attempt to find the RF channel used by the Pro:Centric server as
its data channel. If the Pro:Centric RF channel is found, the DATA
CHANNEL value will be changed from 255 to match the server’s
RF channel number. The time at which the Auto Search occurs
depends on the setting of item 121 P:C RF WAKE HR. See item
121 description for further information.
116 - VIDEO MUTE EN (Video Mute Enable)
Set to 0 for Normal. Set to 1 for Blank.
117 - FACT DEFAULT (Factory Default)
Set to 0 for normal. Set to 1 to restore the factory default settings
of all Installer Menu items.
Note: Pro:Centric updates are downloaded from the Pro:Centric
server to the TV when the TV is turned OFF. While Pro:Centric
updates are in progress, it is not possible to turn ON the TV.
Caution: If set to 1, this will restore the factory defaults
and clear the channel lineup, including any assigned
channel icons and custom text labels.
121 - P:C RF WAKE HR
Note: See also Reference section, “Restoring Factory Defaults on
Set the Wake On RF hour from 0 to 23. This item uses the
24-hour clock format. The value “128” is displayed as “OFF.”
Directly entering 128 turns the Wake On RF feature OFF.
the TV(s),” for further information.
118 - POWER SAVINGS
The Wake On RF feature uses a timer, based on the settings
of this item and item 122 P:C RF WAKE MN, to wake the TV to
check for and, if applicable, download updates.
Default set to 3—the power circuitry for both the embedded b-LAN
module and the GAME CONTROL/MPI port is only powered when
the TV is turned ON. When the TV is turned OFF, the embedded
b-LAN and the GAME CONTROL/MPI port are not powered.
If Wake On RF is OFF, the time at which a Data Channel Auto
Search (item 119 set to 255) occurs is determined as follows: The
TV will initiate the search at 2:00 PM (if the TV clock is set) or at 14
hours of elapsed time from when AC power was applied (if the TV
clock is not set). If the TV display is ON when the Auto Search is
due to occur, the Auto Search will take place the next time the TV is
turned OFF.
Note that the TV must be turned ON in order to communicate with
the embedded b-LAN module for configuration and control when
POWER SAVINGS is set to 3. If POWER SAVINGS is set to 1,
the b-LAN module is always powered.
Similarly, if MPI communication is required for external MPI
control, POWER SAVINGS should be set to 1 so that the GAME
CONTROL/MPI port circuitry is always powered.
Note: This item is not available in the Installer Menu when item
119 DATA CHANNEL is set to 0.
Note: See Reference section, “b-LAN Setup & Overview,” for
Note: The TV clock must be set in order for a Wake On RF event
to occur at the precise time of day in accordance with item 121
and 122 settings.
further information.
Caution: POWER SAVINGS should NEVER be set to 7.
This setting is intended for factory use only.
122 - P:C RF WAKE MN
Set the Wake On RF minute from 0 to 59. See also description for
item 121 P:C RF WAKE HR above.
119 - DATA CHANNEL
Set to 0 to disable. Set from 1 to 135 to match the RF channel
number that will be used by the Pro:Centric server as its data
channel.*
Note: This item is not available in the Installer Menu unless item
121 P:C RF WAKE HR is set from 0 to 23.
Note: The TV clock must be set in order for a Wake On RF event
to occur at the precise time of day in accordance with item 121
and item 122 settings.
* PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.
28
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom Master TV Setup
This section describes how to create a customized Master TV Setup for cloning purposes when the TV is in
Pass-through Mode.
Note: Cloning requirements and procedures are described in detail on pages 34 to 42. Refer to “FTG Mode of
Operation Overview” on pages 43 to 44 for information on FTG Mode operation and configuration.
Cloning Methods
Before You Begin
See also “Clonable TV Setup Menu Features” list below.
• It is recommended that you disconnect all Aux
inputs if you intend to run Auto Tuning (Channel
Search). Under certain conditions, Auto Tuning
is disabled if there is an Aux input active.
Using a USB Memory Device / .tlx File
• The .tlx file format clones Installer Menu settings and all TV
sources’ (analog, digital, AV1, HDMI, etc.) clonable setup menu
settings.
• Determine which cloning tool—USB memory
device or clone programmer—is appropriate for
your application; several of the Master TV Setup
procedure steps are dependent on the cloning
tool to be used. See “Cloning Methods” at right
for further information.
• Not intended for cloning an auto-tuned/edited Channel Map, as
the channel lineup is converted to a logical FTG Channel Map
when saved (Learned) from a TV to a .tlx file. If the .tlx file with
the FTG Channel Map is then used for Teaching purposes, all
Target TVs will be configured for FTG Mode via CPU.
• If you intend to use a USB memory device,
determine the type of file—either the new “.tlx”
file format or the legacy “.tll” file format—to use
for cloning purposes; several of the Master TV
Setup procedure steps are dependent on the
desired file type. See “Cloning Methods” at right
for further information.
Using a USB Memory Device / .tll File
The .tll file format clones the contents of the commercial controller
(PTC) memory, including an auto-tuned/edited Channel Map,
Installer Menu settings, and one TV source’s (analog, digital, or
Aux) clonable setup menu settings.
Using a Clone Programmer (TLL-1100A or LT2002)
• If the EZ-Manager Wizard appears on the screen,
exit the wizard before beginning/continuing the
Custom Master TV Setup procedure.
Both the TLL-1100A and LT2002 clone the contents of the
commercial controller (PTC) memory, including an auto-tuned/
edited Channel Map, Installer Menu settings, and one TV source’s
(analog or Aux) clonable setup menu settings.
Clonable TV Setup Menu Features
Channel
Audio
Auto Volume
Clear Voice
Sound Mode
Balance
Time
Auto Tuning (Channel Lineup)
Manual Tuning
Channel Edit
Clock Mode (Auto/Manual) *
Time Zone
Auto Off
Channel Label
Option
Language
Caption
TV Speaker
Picture
Picture Mode *
Standby Light
* Advanced Control (Picture Mode) and DST (Clock Mode) settings are cloned via .tlx file only.
Note: Some menu options vary between analog and digital channels and Aux inputs.
206-4232
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom Master TV Setup (Cont.)
Custom Master TV Setup Procedure
1. Turn ON the TV.
If the EZ-Manager Wizard appears on the screen when you turn ON the TV, use the arrow
keys on the Installer Remote to select Exit from the Welcome screen and press OK. In the
confirmation pop-up window, select OK, and then press OK once more on the Installer
Remote to exit the wizard.
2. Set Installer Menu items.
This step provides specific instruction only on the Installer Menu items
that should be set on a Master TV. Refer to pages 20 to 28 for detailed
xxLP645H PTC INSTALLER MENU
information on all Installer Menu items.
CPU-CTV
a) Use the Installer Remote to access the PTC Installer Menu (see
“Accessing the Installer Menu” on page 20 for further information).
000 INSTALLER SEQ
000
The next step depends on whether the EZ-Manager Wizard
appeared when you turned ON the TV:
UPN 000-000-000-000
PTC V1.00.022
ASIC D27D
CPU V3.35.00
• If the wizard did appear, the TV is in a factory default state, and
you can proceed to set Installer Menu items. Go to step (c).
• If the wizard did not appear, go to step (b).
Typical Installer Menu
b) Set Installer Menu item 117 FACT DEFAULT to 1 and press OK on
Note: The Installer Menu header will vary
depending on the TV you are setting up.
the Installer Remote.
This clears all Installer Menu custom settings, channel lineup, etc.
and restores the factory default settings. The value will change
back to 0 after the PTC has been restored to factory default
condition. This step ensures that the TV Channel Memory will be
the active channel lineup.
117 FACT DEFAULT
003 BAND/AFC
000
001
Adjust the values for these
Installer Menu items, as required.
c) Set Installer Menu item 003 BAND/AFC, as appropriate.
• Broadcast: Set to 0.
• HRC: Set to 2.
• IRC: Set to 3.
• CATV: Set to 1 (default).
d) Set any other Installer Menu items that affect your TV programming
network to the required configuration. For example, enable/disable
Aux inputs, set a Start Channel, etc.
PICTURE
LOCK
TIME
AUDIO
CHANNEL
INPUT
e) After you have adjusted all Installer Menu item settings as required,
press OK once on the Installer Remote to save your changes; then,
press OK again to exit the menu.
OPTION
MY MEDIA
3. Set up TV features.
On-screen setup menus control the features of the TV. Press MENU
SETTINGS on the Installer Remote to access the TV setup menus,
and then set Channel, Picture, Audio, Time, etc. options to the
desired configurations. See “Clonable TV Setup Menu Features” list
on previous page and also notes on the following page.
Use the TV setup menus to set the TV
features to the desired configuration
for the end user.
(Continued on next page)
30
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom Master TV Setup (Cont.)
(Continued from previous page)
Note: If you intend to use a USB memory device / .tlx file for cloning purposes, and you wish
to use the TV Zoning feature, make sure to assign a TV Zone # at this time as described in
Reference section, “Using the TV Zoning Feature.”
Note: If you intend to clone the PTC, remember that only one TV source’s clonable setup
menu settings will be cloned. Thus, for a clone programmer, the TV setup menu settings
should be applicable to either an analog channel or Aux input, while for a USB device / .tll file,
the TV setup menu settings should be applicable to the analog or digital channel or Aux input
to which the Target TV will be set during the Teaching process.
Note: If desired and if appropriate depending on the cloning method to be used (see “Cloning
Methods” on page 29), you can run Auto Tuning (see step 4) prior to completing this step.
Note: The next three steps (4 to 6) are applicable for PTC cloning only (i.e., cloning using
a USB memory device / .tll file or clone programmer). If you intend to use a USB memory
device / .tlx file for cloning purposes, proceed directly to step 7 to verify the TV setup.
4. (PTC cloning only / Optional) Run Auto Tuning.
Note: If you run Auto Tuning with the intention to clone the resulting Channel
Map, you MUST use a USB memory device / .tll file or a clone programmer
for this cloning purpose. If you Teach a .tlx file with an auto-tuned/edited
Channel Map to a Target TV, this will put the Target TV in FTG Mode via CPU.
CHANNEL
Move
OK
• Auto Tuning
• Manual Tuning
• Channel Edit
• Channel Label
a) To search for all available analog and digital channels, go to the Channel
Menu, select the Auto Tuning option, and follow the on-screen instructions.
b) Use the Channel Edit option in the Channel Menu to edit the channel
lineup, as necessary, to include only free to guest (non-encrypted) channels.
• Add/delete channels per your system requirements.
• Use the Channel Label option in the Channel Menu to select the
appropriate trademark/icon for each channel’s Channel-Time on-screen
display. Icons are available for familiar channels, such as ABC, CBS,
NBC, etc. Identifiable labels (icons) should enable the end user to readily
know what common networks are available.
(Optional) Use Channel Menu options
to run Auto Tuning, edit channels, and
select channel icons.
Note: If Installer Menu item 103 ATSC TUNE MODE is set for Physical
Channel tuning (default and recommended setting), channels with minor
channel numbers higher than 255 will not transfer correctly in step 5. If item
103 is set for Virtual Channel tuning and either the major or minor channel
numbers are higher than 255, the channel(s) will not transfer correctly in
step 5.
Note: You can add the channel icons in this step or as described in step 6.
Also in step 6, you can add custom text labels for channels without icons.
(Continued on next page)
206-4232
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom Master TV Setup (Cont.)
(Continued from previous page)
5. (PTC cloning only) Transfer the TV setup menu settings to the commercial controller (PTC):
2-5-5 + MENU Mode
Note: This step is essential for successful cloning using a USB memory device / .tll
file or a clone programmer. Without this step, the PTC will not contain any of the TV
setup menu settings.
Note: The maximum number of channels (analog, digital, and Aux inputs) that can
be transferred to the PTC is 141. An attempt to transfer more than 141 channels of
any combination will result in a PTC Channel Map of exactly 141 channels; any extra
channels will not be available in the PTC Channel Map. For example, if you enabled
three Aux inputs in the Installer Menu and Auto Tuning found 141 channels, you must
edit the TV channel lineup to decrease the number of analog/digital channels to (at
most) 138 in order to accommodate the Aux inputs in the PTC Channel Map.
a) After the TV channel lineup has been edited and channel label icons added, tune to the
channel (source) for which you wish to transfer TV setup menu settings.
Note: If you intend to use a clone programmer for cloning purposes, this must be either
an analog channel or Aux input.
b) Access the Installer Menu, and press 2-5-5 + MENU SETTINGS on the Installer Remote to
initiate the transfer of the Master TV Setup to the PTC. The TV exits the Installer Menu and
then tunes through the channels in the channel lineup during the transfer. When the transfer
is complete, the TV tunes back to the channel that was tuned before the transfer began.
6. (PTC cloning only / Optional) Add Custom Channel and Aux
Input Labels: 2-5-4 + MENU Mode
DIGITAL 19-3
Note: 2-5-4 + MENU Mode enables you to add/edit channel icons and
custom text labels in the PTC once the Master TV Setup has been
transferred as described in the previous step.
MONO STEREO SAP
Access the Installer Menu, and press 2-5-4 + MENU SETTINGS on the
Installer Remote. Add/edit custom text labels and/or change icons for
the Channel-Time on-screen displays (see 2-5-4 + MENU procedural
information on page 33). Note that broadcast digital channels often
already have a broadcaster generated label. When you are finished,
press MENU SETTINGS to exit 2-5-4 + MENU Mode.
WXYZ
Custom text label “WXYZ” created
in 2-5-4 + MENU Mode.
7. Verify the TV setup.
Make sure the TV features are set per your requirements. Also, if
cloning the PTC, verify that the channel lineup, channel icons, and
custom text labels are correct.
028 CH. OVERIDE
000
After verifying the TV Setup, set Installer
Menu item 028 CH. OVERIDE to 0.*
8. (Recommended) Lock the channel lineup.
* This step prevents end users from
accessing channel settings (i.e., the
Channel Menu will be inaccessible/
grayed out).
Access the Installer Menu. Set item 028 CH. OVERIDE to 0 and press
OK to lock the channel lineup and restrict access to the TV setup
menus. Press OK again to save your changes and exit the Installer
Menu.*
The Master TV Setup is now ready to be copied to the predetermined
cloning tool—a USB memory device (.tlx or .tll file) or a clone programmer.
See cloning procedures in this document.
32
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel Icons / Custom Text Labels (2-5-4 + MENU Mode)
Changing Channel Icons and/or Adding or Editing
Custom Text Labels in the Channel-Time Display
Changing icons and/or adding or editing custom text labels
can only be done if there are channels that have been
transferred to the TV’s PTC either during Master TV Setup
(see pages 29 to 32) or by cloning.
If there is no pre-assigned icon for a channel, you can add
a custom text label of up to seven (7) characters to help
identify the channel or network. Also, if desired, a custom
text label can be added to the Channel-Time display in
addition to a pre-assigned icon. You may also add text
labels for the Aux input sources to clearly identify the
devices that are connected to the Aux inputs.
Note: A blank letter space is available between “Z” and “!”.
To perform channel editing/labeling:
1. Use the Installer Remote to access the Installer Menu
(see “Accessing the Installer Menu” on page 20 for
further information).
(Icon)
2. Press 2-5-4 + MENU SETTINGS on the Installer
Remote to access the Channel Label Editing Menu.
XYZ
XYZ
XYZ
3. Change channel icons and/or add or edit custom text
labels as described in the procedures below. (You can
do this more than once.)
NETWORK
(Custom Text Label)
1 2 3 4 5
7
6
4. To exit the menu when done, press MENU SETTINGS.
Changing a Channel’s Icon on
the Master TV
Adding/Editing Channel Labels
on the Master TV
Adding/Editing Source Labels
on the Master TV
1. Use Channel Up/Down to select
the desired channel.
1. Use Channel Up/Down to select
the desired channel.
1. Press INPUT to select the desired
Aux input source: AV, RGB, HDMI,
HDMI2, or HDMI3.
2. Use the Left/Right arrow keys
to select the thin letter “I” on the
Channel-Time display.
2. Press the Left or Right arrow
repeatedly until the numbers 1 to 7
appear on the display. The number
shows the position of the character
that can be changed. Number 1 is
the first character, number 2 the
second character, etc.
2. Press the Left or Right arrow
repeatedly until the numbers 0 to 9
appear on the display. The number
shows the position of the character
that can be changed.
3. Use the Up/Down arrow keys to
select the icon with which you want
to identify the channel. (If you know
the icon number, enter the number,
and press OK.)
3. Use the Up/Down arrow keys to
select the desired character.
3. Use the Up/Down arrow keys to
select the desired character.
4. Proceed to add/edit custom text
labels, or go to the next channel.
4. Press INPUT for the next Aux input,
or use Channel Up/Down to return
to channels.
4. Proceed to the next number posi-
tion, or go to the next channel.
Installer Remote Control Key Functions for Master TV Channel Label Editing Menu
• Channel Up/Down: Tunes to the next channel in scan.
• Left/Right Arrows: Select the item to change. If “I” is
shown, the icon can be changed. If a number is shown, it
indicates the position of the character that can be changed.
• Up/Down Arrows: Select the icon or the character to be
displayed. Tip: Arrows can be held down for fast scrolling.
• 0 – 9: Use to enter the index number of the icon, if
known.
• OK: Changes the icon after the icon number has been
entered.
• INPUT: Changes the Aux input label.
• MENU SETTINGS: Exits the editing process.
206-4232
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Cloning Overview
IMPORTANT CLONING INFORMATION
There are four different procedures for cloning a Master TV Setup, each with its own advantages and
limitations (see also “Cloning Methods” on page 29):
• Using a USB memory device / .tlx file
• Using a USB memory device / .tll file
• Using a TLL-1100A clone programmer
• Using a LT2002 clone programmer
Each cloning method is described in further detail on the pages that follow. As you perform cloning
procedures, be sure to complete each task as indicated. If a procedure or step is omitted or not
performed completely, cloning may not work. At each step, pay attention to ensure the TV screen shows
the proper message when cloning. If the message indicated does not appear, there is a problem with that
step, and cloning may not be successful.
Caution: Copying a blank or incorrect memory into a TV from a clone programmer will
cause the TV to operate erratically or become inoperable.
Caution: If the TV is in LodgeNet PPV Mode or FTG Mode via EBL (check with the site
administrator if you are not certain), do not connect a clone programmer to the GAME
CONTROL/MPI port, as this will damage the clone programmer.
Before you begin cloning:
• Complete the Custom Master TV Setup procedure (see pages 29 to 32).
• All equipment should be connected to power and turned ON.
• Both the Master and Target TVs must be in Pass-through Mode (i.e., the TV setup menus should be
displayed when you press MENU SETTINGS on the Installer Remote).
• Learning and Teaching is only possible between identical model TVs. In the case of the LP645H models,
the chassis size is also important. In particular, a 60LP645H TV should only be cloned using a Master TV
Setup created from another 60LP645H TV.
• If using a USB memory device, ensure the USB device has been formatted with FAT format.
• If using a USB memory device / .tlx file, ensure that the Master TV Setup does not contain a Channel
Map; otherwise, Teaching will result in the Target TV(s) being configured for FTG Mode via CPU.
• For both Master and Target TVs—If using a clone programmer, ensure the TV is tuned to either an Aux
input or an analog (not a digital) channel.
• LT2002 only—Make sure the batteries in the clone programmer are fresh. If batteries are removed, the
clone programmer clock time (if set) will be lost (see page 41 for information on the clone programmer
clock).
Caution: Do not unplug the TV power cord or remove/disconnect the USB memory device/
clone programmer while Learning or Teaching, as doing so may cause the TV to malfunction
or harm the USB device/clone programmer, respectively.
34
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
USB Cloning Procedures
Learning / Teaching a Master TV Setup using a USB Memory Device / .tlx File
USB Cloning Notes
• Read the IMPORTANT CLONING INFORMATION on page 34 before beginning
any cloning procedures. In particular, ensure that the Master TV Setup does not
contain a Channel Map; otherwise, Teaching will result in the Target TV(s) being
configured for FTG Mode via CPU.
• If a TV Zone # (for location-specific configuration) has been set in the Master
TV before the Learning process is initiated, the Zone designation will be used
during the subsequent Teaching process(es). This means that in order for the
“Learned” clone data with the TV Zone assignment to be applied, any Target
TVs will need to be assigned the same Zone designation BEFORE Teaching
is performed. Refer to Reference section, “Using the TV Zoning Feature,” for
further information. See also bullet below.
• If you intend to use the TV Zoning feature, make sure to assign a TV Zone #
as described in Reference section, “Using the TV Zoning Feature,” BEFORE
continuing with the Learning procedure below. See also bullet above.
• You may edit the filename as part of the Learning procedure; however, a file
with edited contents will not be recognized.
• It is not possible to clone a Master TV’s clock using a USB memory device.
Either set a Target TV’s clock manually, or use the Auto Clock setting in the TV
setup menus.
USB Download Menu
Learn Setup from Master TV
Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
1. Ensure the Master TV is set up completely and in Pass-through Mode.
2. Insert the USB memory device into the USB IN port on the Master TV.
Teach To TV (TLX)
3. Press MENU SETTINGS on the Installer Remote to display the TV setup
menus. Use the arrow navigation keys to select/highlight the Option menu
icon, and then press the number “7” key a total of seven times to display the
USB Download Menu.
Learn From TV (TLL)
Learn From TV (TLX)
Previous
OK
4. To gain access to the “Learn From TV” option in the USB Download Menu, key
Learn From TV (TLX)
in the password used to access the Installer Menu (Example: Press 9-8-7-6).
Select the file name and press OK to start
5. Use the Up/Down arrow keys to select Learn From TV (TLX), and then
press OK.
xxLP645H-UA00003.TLX
6. To differentiate this .tlx file from others, you can use the Up/Down arrow keys
to change the last five digits of the filename. Press OK when you are ready
to initiate Learning.
Previous
OK
Learn From TV
Learning status will be shown on a progress bar in a new window. When the
Learning process is complete, the USB Download menu will reappear on the
screen.
UPDATING...
Do not unplug!
25%
7. When Learning is done, press on the Installer Remote to exit the USB
Download Menu, and remove the USB memory device from the Master TV.
206-4232
35
Download from Www.Somanuals.com. All Manuals Search And Download.
USB Cloning Procedures (Cont.)
Teach Master TV Setup to Target TV
1. Turn ON the Target TV.
The next step depends on whether the EZ-Manager Wizard appears on the screen:
• If the wizard is displayed, the TV is in the required factory default state. If desired, you can
complete the Teaching process via the EZ-Manager Wizard (see “USB Configuration” on
page 17) or using the LG Smart Install utility (see “LG Smart Install Utility” on pages 18 to
19). To continue with this procedure, exit the wizard: Use the arrow keys on the Installer
Remote to select Exit from the Welcome screen and press OK. In the confirmation pop-up
window, select OK, and then press OK once more on the Installer Remote.
Then, go to step 3.
• Otherwise, ensure the Target TV is in Pass-through Mode, and then continue with step 2.
Note: If the Master TV Setup contains a TV Zone # assignment, in order for
the proper location-specific TV Zone profile data to be applied, you will need
to assign the same Zone designation in the Target TV(s) BEFORE Teaching is
performed. Refer to Reference section, “Using the TV Zoning Feature,” for
further information.
2. Use the Installer Remote to access the Target TV Installer Menu (see
“Accessing the Installer Menu” on page 20 for further information). Set
Installer Menu item 117 FACT DEFAULT to 1, and press OK. When the value
changes back to 0, press OK again to exit the Installer Menu.
USB Download Menu
Note: This step restores factory default settings on the TV. If applicable, set
the TV Zone # (see note above); and then continue with step 3.
Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
3. Insert the USB memory device with the .tlx file into the Target TV USB IN
port.
Teach To TV (TLX)
4. Press MENU SETTINGS on the Installer Remote to display the TV setup
menus. Use the arrow navigation keys to select/highlight the Option menu
icon, and then press the number “7” key a total of seven times to display the
USB Download Menu.
Previous
OK
Teach To TV (TLX)
xxLP645H-UA00003.TLX
5. Use the Up/Down arrow keys to select Teach To TV (TLX), and then press
OK.
6. Use the Up/Down arrow keys to select the Master TV Setup you want to
install, and then press OK. Note: Filenames identify the TV, the TLX
version, and, in the case of the 60LP645H model, the chassis size.
Previous
OK
Teach To TV
Teaching status will be shown on a progress bar in a new window. When the
Teaching process is complete, the TV will briefly display a “Teaching
Completed” window and then exit the USB Download Menu.
UPDATING...
Do not unplug!
50%
7. Remove the USB memory device from the Target TV, and verify that the
Master TV Setup is now resident on the Target TV.
Note: After the Teaching process is complete, the TV tunes according to the
setting of Installer Menu item 004 STRT CHANNEL (Start Channel). If a Start
Channel is specified, the TV will tune to that channel; otherwise, the TV will
return to the last channel tuned.
36
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
USB Cloning Procedures (Cont.)
Learning / Teaching a Master TV Setup using a USB Memory Device / .tll File
USB Cloning Notes
• Read the IMPORTANT CLONING INFORMATION on page 34 before beginning
any cloning procedures.
• You may edit the filename as part of the Learning procedure; however, a file
with edited contents will not be recognized.
• It is not possible to clone a Master TV’s clock using a USB memory device.
Either set a Target TV’s clock manually, or use the Auto Clock setting in the TV
setup menus.
USB Download Menu
Learn Setup from Master TV
Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
1. Ensure the Master TV is set up completely and in Pass-through Mode.
2. Insert the USB memory device into the USB IN port on the Master TV.
Teach To TV (TLX)
3. Press MENU SETTINGS on the Installer Remote to display the TV setup
menus. Use the arrow navigation keys to select/highlight the Option menu
icon, and then press the number “7” key a total of seven times to display the
USB Download Menu.
Learn From TV (TLL)
Learn From TV (TLX)
Previous
OK
4. To gain access to the “Learn From TV” option in the USB Download Menu, key
Learn From TV (TLL)
in the password used to access the Installer Menu (Example: Press 9-8-7-6).
Select the file name and press OK to start
5. Use the Up/Down arrow keys to select Learn From TV (TLL), and then
press OK.
xxLP645H-UA00001.TLL
6. To differentiate this .tll file from others, you can use the Up/Down arrow keys
to change the last five digits of the filename. Press OK when you are ready
to initiate Learning.
Previous
OK
Learn From TV
Learning status will be shown on a progress bar in a new window. When the
Learning process is complete, the USB Download Menu will reappear on the
screen.
UPDATING...
25%
Do not remove the USB from the port!
Do not unplug!
7. When Learning is done, press on the Installer Remote to exit the USB
Download Menu, and remove the USB memory device from the Master TV.
206-4232
37
Download from Www.Somanuals.com. All Manuals Search And Download.
USB Cloning Procedures (Cont.)
Teach Master TV Setup to Target TV
1. Turn ON the Target TV.
The next step depends on whether the EZ-Manager Wizard appears on the
screen:
• If the wizard is displayed, the TV is in the required factory default state. If
desired, you can complete the Teaching process via the EZ-Manager Wizard
(see “USB Configuration” on page 17). To continue with this procedure, exit
the wizard: Use the arrow keys on the Installer Remote to select Exit from
the Welcome screen and press OK. In the confirmation pop-up window,
select OK, and then press OK once more on the Installer Remote.
Then, go to step 3.
• Otherwise, ensure the Target TV is in Pass-through Mode, and then
continue with step 2.
2. Use the Installer Remote to access the Target TV Installer Menu (see
“Accessing the Installer Menu” on page 20 for further information). Set
Installer Menu item 117 FACT DEFAULT to 1, and press OK. When the
value changes back to 0, press OK again to exit the Installer Menu.
Note: This step restores factory default settings on the TV.
3. Tune/set the TV to an analog or digital channel or Aux input (ideally the same
source tuned for 2-5-5 + MENU Mode during the Master TV Setup procedure).
4. Insert the USB memory device with the .tll file into the Target TV USB IN
port.
USB Download Menu
Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
5. Press MENU SETTINGS on the Installer Remote to display the TV setup
menus. Use the arrow navigation keys to select/highlight the Option menu
icon, and then press the number “7” key a total of seven times to display the
USB Download Menu.
Teach To TV (TLX)
Previous
OK
6. Use the Up/Down arrow keys to select Teach To TV (TLL), and then press
OK.
Teach To TV (TLL)
7. Use the Up/Down arrow keys to select the Master TV Setup you want to
install, and then press OK. Note: Filenames identify the TV, the TLX
version, and, in the case of the 60LP645H model, the chassis size.
xxLP645H-UA00001.TLL
Teaching status will be shown on a progress bar in a new window. When the
Teaching process is complete, the USB Download menu will reappear on
the screen.
Previous
OK
Teach To TV
8. When Teaching is done, press on the Installer Remote to exit the USB
Download Menu, remove the USB memory device from the Target TV, and
turn OFF the TV.
UPDATING...
50%
Do not remove the USB from the port!
Do not unplug!
9. After a few seconds, turn ON the TV, and verify that the Master TV Setup is
now resident on the Target TV.
Note: When you turn it back ON, the TV will tune according to the setting of
Installer Menu item 004 STRT CHANNEL (Start Channel). If a Start Channel is
specified, the TV will tune to that channel; otherwise, the TV will return to the
last channel tuned.
38
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Clone Programmer Cloning Procedures
Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer
Caution: If the TV is in LodgeNet PPV Mode or FTG Mode via EBL (check with the site
administrator if you are not certain), do not connect a clone programmer to the GAME
CONTROL/MPI port, as this will damage the clone programmer.
Cloning is accomplished using the
TV/clone programmer MPI ports for
communication (see figure).
TLL-1100A Clone
Programmer
TV Link
Loader
TLL1100A
Ready
Antenna
or CATV
TLL-1100A Cloning Notes
• Read the IMPORTANT CLONING
INFORMATION on page 34 before
beginning any cloning procedures.
MODE
MENU
CLONE SELECTION MENU
Selected Bank: CBankX Saved
(1) LEARN FROM TV
MPI
Cable
ENTER
• Ensure the TLL-1100A is either fully
charged or connected to AC power.
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
RECEIVE
SEND
(6) DISPLAY CLONE SETUP
• Learning and Teaching is only
possible between identical model
TVs; however, the TLL-1100A can
store up to eight different Master
TV Setups.
TLL-1100A
Learn Setup from Master TV
1. Ensure the Master TV is set up completely and in Pass-through Mode.
2. Tune/set the TV to an analog channel or Aux input, and then, plug one end
of the MPI cable into the TV MPI port.
3. Turn ON the TLL-1100A.
4. Use the MODE button on the TLL-1100A to select Clone Mode.
5. Use the Left/Right arrows on the TLL-1100A to select the Memory CBank
(1 to 8) in which to store the Master TV Setup.
CLONE SELECTION MENU
Selected Bank: CBankX Saved
(1) LEARN FROM TV
6. Plug the other end of the MPI cable into the MPI port on the bottom of the
TLL-1100A. The Clone Selection Menu will display on the TV screen.
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
7. Press 1 on the Installer Remote to select LEARN FROM TV from the
Clone Selection Menu. Then, press OK to transfer the Master TV Setup
into CBankX on the TLL-1100A.
(6) DISPLAY CLONE SETUP
CLONE CLOCK = XX:XX
Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will
be displayed on the screen while the TLL-1100A copies the Master Setup.
When the Learning process is complete, a “LEARNING COMPLETE”
message will be displayed.
TV
CLOCK = XX:XX
THE CLONE IS VERSION VX.X.X
-
-
To change menu items, press
channel keys or digits.
To execute item, press Enter.
8. When Learning is complete, disconnect the MPI cable from the Master TV.
206-4232
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Clone Programmer Cloning Procedures (Cont.)
(Optional) Set the Clock
CLONE SELECTION MENU
Selected Bank: CBankX Saved
(1) LEARN FROM TV
Set the time on a Master TV’s clock. (If the time has already been copied
from a TV into the TLL-1100A clone programmer, you can set the Master
TV’s clock by copying the time from the clone programmer.) The TLL-1100A
can copy the current time to both a Master TV and to the clone’s internal
clock—accurate to within one minute.
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
Since the TLL-1100A’s time cannot be set directly, the current time needs
to be copied from an LG TV equipped with an enabled MPI port.
CLONE CLOCK = XX:XX
TV
CLOCK = XX:XX
After the time is copied to the TLL-1100A clone programmer, the current
time will be maintained and can then be transferred to another TV. (This can
be a Master TV or another TV which has already had the features set up.)
THE CLONE IS VERSION VX.X.X
-
-
To change menu items, press
channel keys or digits.
To execute item, press Enter.
Teach Master TV Setup to Target TV
1. Turn ON the Target TV.
The next step depends on whether the EZ-Manager Wizard appears on
the screen when you turn ON the TV:
• If the wizard is displayed, the TV is in the required factory default state.
Use the arrow keys on the Installer Remote to select Exit from the
Welcome screen and press OK. In the confirmation pop-up window,
select OK, and then press OK once more on the Installer Remote to
exit the wizard. Then, go to step 3.
• Otherwise, ensure the Target TV is in Pass-through Mode. Then,
continue with step 2.
2. Use the Installer Remote to access the Target TV Installer Menu (see
“Accessing the Installer Menu” on page 20 for further information). Set
Installer Menu item 117 FACT DEFAULT to 1, and press OK. When the
value changes back to 0, press OK again to exit the Installer Menu.
Note: This step restores factory default settings on the TV.
3. Tune/set the TV to an analog channel or Aux input (ideally the same
source tuned for 2-5-5 + MENU Mode during the Master TV Setup
procedure), and then connect the MPI cable to the MPI port on the Target
TV. The Clone Selection Menu will display on the TV screen.
CLONE SELECTION MENU
Selected Bank: CBankX Saved
(1) LEARN FROM TV
4. Ensure the correct Memory CBank(X) is selected on the TLL-1100A.
5. Press 2 on the Installer Remote to select TEACH TO TV from the Clone
Selection Menu. Then, press OK to transfer the Master TV Setup to the
Target TV.
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
Teaching usually takes 3 to 4 minutes. “TEACHING IN PROGRESS” will
be displayed on the screen during Teaching. When the Teaching process
is complete, a “TEACHING COMPLETE” message will be displayed.
(6) DISPLAY CLONE SETUP
CLONE CLOCK = XX:XX
TV
CLOCK = XX:XX
THE CLONE IS VERSION VX.X.X
6. When Teaching is done, disconnect the MPI cable from the Target TV,
and turn OFF the TV.
-
-
To change menu items, press
channel keys or digits.
To execute item, press Enter.
7. After a few seconds, turn ON the TV, and verify that the Master TV
Setup is now resident on the Target TV.
40
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Clone Programmer Cloning Procedures (Cont.)
Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer
Caution: If the TV is in LodgeNet PPV Mode or FTG Mode via EBL (check with the site
administrator if you are not certain), do not connect a clone programmer to the GAME
CONTROL/MPI port, as this will damage the clone programmer.
Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure).
LT2002 Cloning Notes
• Read the IMPORTANT CLONING
MPI
INFORMATION on page 34 before
beginning any cloning procedures.
Cable
Antenna
or CATV
• A slow flashing green light indicates
that there are communication
problems between the TV and the
LT2002. If this is the case, check for
a damaged cable, poor contacts, or
other connection troubles.
Ferrite Core
(TDK, ZCAT
2035-0930)
Connect cable to
TV MPI Jack and
follow on screen
instructions
Status
Indicator
MPI
Reset
Color
•
•
green
red
battery ok
battery low
Blink pattern
power on
no communications
• If the status indicator is red, the
LT2002 batteries are low and should
be replaced. Install four (4) high-
quality alkaline AA batteries.
•
•
slow
heartbeat power on
communications ok
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION
THE SW IS REVISION
XX
XX
CLONE CLOCK
TV CLOCK
=
=
XX:XX
XX:XX
®
• Learning and Teaching is only
possible between identical model TVs;
however, the LT2002 can store up to
three different Master TV Setups.
- PRESS ANY KEY TO CONTINUE.
QuickSet II Programmer
- DISCONNECT CLONE WHEN DONE.
LT2002
LT2002 Clone
Programmer
ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA
Learn Setup from Master TV
1. Ensure the Master TV is set up completely and in Pass-through Mode.
CLONE SELECTION MENU
2. Tune/set the TV to an analog channel or Aux input, and then plug one end of
the MPI cable into the TV MPI port.
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
3. If there is a good connection after the LT2002 is connected to the TV MPI
port, “THE CLONE HAS CONTROL OF THE TV” message will appear on
the TV screen. Press any key on the Installer Remote to access the LT2002
Clone Selection Menu.
(6) DISPLAY CLONE SETUP
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
4. Press 1 on the Installer Remote to select LEARN FROM TV from the Clone
Selection Menu; then press OK to proceed to the Memory Bank Selection
Menu.
- TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
5. Press 1, 2, or 3 on the Installer Remote to select the clone Memory Bank in
SAVE TV SETUP IN SELECTED
CLONE MEMORY
which to store the Master Setup. Then, press OK.
Note: If you choose a Memory Bank that already has a Master device’s setup
programmed into it, that setup will be overwritten by the new Master TV Setup.
(1) MEMORY 1 VER XX REV XX
(2) MEMORY 2 VER XX REV XX
(3) MEMORY 3 VER XX REV XX
(4) RETURN TO CLONE MENU
6. Verify the Learning setup information on the next screen, and then press
POWER to transfer the Master TV Setup into the selected Memory Bank on
the LT2002.
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will
be displayed on the screen while the LT2002 copies the Master Setup. When
the Learning process is complete, a “LEARNING COMPLETE” message will
be displayed.
- TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
7. When Learning is complete, disconnect the MPI cable from the Master TV.
206-4232
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Clone Programmer Cloning Procedures (Cont.)
(Optional) Set the Clock
Set the time on a Master TV’s clock. (If the time has already been copied from a
TV into the LT2002 clone programmer, you can set the Master TV’s clock by
copying the time from the clone programmer.) The LT2002 can copy the current
time to both a Master TV and to the clone’s internal clock—accurate to within one
minute. (Another reason that the LT2002 should be equipped with fresh, high-
quality alkaline batteries, is for it to keep the time as accurately as possible.)
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
Since the LT2002’s time cannot be set directly, the current time needs to be
copied from an LG TV equipped with an enabled MPI port.
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
- TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
After the time is copied to the LT2002 clone programmer, the current time will be
maintained and can then be transferred to another TV. (This can be a Master TV
or another TV which has already had the features set up.)
Teach Master TV Setup to Target TV
1. Turn ON the Target TV.
The next step depends on whether the EZ-Manager Wizard appears on the
screen when you turn ON the TV:
• If the wizard is displayed, the TV is in the required factory default state. Use
the arrow keys on the Installer Remote to select Exit from the Welcome
screen and press OK. In the confirmation pop-up window, select OK, and
then press OK once more on the Installer Remote to exit the wizard. Then,
go to step 3.
• Otherwise, ensure the Target TV is in Pass-through Mode. Then, continue with
step 2.
2. Use the Installer Remote to access the Target TV Installer Menu (see “Access-
ing the Installer Menu” on page 20 for further information). Set Installer Menu
item 117 FACT DEFAULT to 1, and press OK. When the value changes back to
0, press OK again to exit the Installer Menu.
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
Note: This step restores factory default settings on the TV.
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
3. Tune/set the TV to an analog channel or Aux input (ideally the same source
tuned for 2-5-5 + MENU Mode during the Master TV Setup procedure), and
then connect the MPI cable to the MPI port on the Target TV.
(6) DISPLAY CLONE SETUP
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
4. With “THE CLONE HAS CONTROL OF TV” message on display, press 2 on
the Installer Remote to select TEACH TO TV from the LT2002 Clone Selection
Menu. Then, press OK.
- TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
5. Select the LT2002 Memory Bank in which the new Master TV Setup is located,
and press OK.
COPY SELECTED CLONE MEMORY
TO TV
6. Verify the Teaching setup information on the next screen, and then press
POWER to transfer the Master TV Setup to the Target TV.
(1) MEMORY 1 VER XX REV XX
(2) MEMORY 2 VER XX REV XX
(3) MEMORY 3 VER XX REV XX
(4) RETURN TO CLONE MENU
Teaching usually takes 3 to 4 minutes. “TEACHING IN PROGRESS” will be
displayed on-screen during Teaching. When the Teaching process is complete,
a “TEACHING COMPLETE” message will be displayed.
-
TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
7. When Teaching is done, disconnect the MPI cable from the Target TV, and turn
OFF the TV.
- TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER.
8. After a few seconds, turn ON the TV, and verify that the Master TV Setup is
now resident on the Target TV.
42
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode of Operation Overview
FTG Mode via CPU or EBL
FTG Mode enables Pro:Idiom decryption and also allows logical channel mapping of physical channels.
As indicated in the introduction to this document, there are two separate and distinct methods for configuring
LP645H TVs for FTG Mode of operation: one (new) method is to configure the TV CPU for FTG Mode
operation, while the other is to configure the TV EBL for FTG Mode operation. FROM A LOCAL
CONFIGURATION STANDPOINT, EACH OF THESE METHODS IS MUTUALLY EXCLUSIVE. IF THE
CPU IS IN FTG MODE, THE EBL CANNOT BE SWITCHED TO FTG MODE. LIKEWISE, IF THE EBL IS
IN FTG MODE, THE CPU CANNOT BE SWITCHED TO FTG MODE.
FTG Mode via CPU
FTG Mode via EBL
This mode provides the following features:
This mode provides the following features:
• Logical channels mapped to RF delivered content.
• Digital RF channel minor (program) numbers up to 999.
• FTG Channel Map of up to 600 logical channels.
• Start Channel set for RF or Aux input delivered content.
• Pro:Centric data delivery over RF.
• Logical channels mapped to RF delivered content.
• Digital RF channel minor (program) numbers up to 255.
• FTG Channel Map of up to 141 logical channels.
• Start Channel set for RF or Aux input delivered content.
• Pro:Centric data delivery over RF.
• TV Zoning option for location-specific configuration.
FTG Mode via EBL requires that you use LG FTG Device
Configuration Application PC software to configure the EBL.
In this mode, the EBL is the owner of the FTG Channel Map
and must be configured with an FTG Channel Map and FTG
Installer Menu settings using one of the following processes:
FTG Mode via CPU requires that you use LG FTG File
Manager PC software to create an FTG Configuration (.tlx)
file, which will in turn be used to configure the CPU. In this
mode, the CPU is the owner of the FTG Channel Map and
must be configured with an FTG Channel Map and FTG
Installer Menu settings using one of the following processes:
• Local: Configure an individual LP645H TV’s EBL via its
TV-LINK CFG jack using a direct PC-to-TV connection and
the FTG Device Configuration Application. See Reference
section, “FTG Mode via EBL (Local Configuration),” for
information on the “Write” process for an FTG Channel
Map and FTG Installer Menu settings.
• Local: Configure an individual LP645H TV via its USB port
using an FTG Configuration (.tlx) file on a USB memory
device. The “Teach to TV (TLX)” process, along with
associated procedures, is described on pages 45 to 49.
• Remote: Configure all LP645H TV EBLs at the site using
a Free-To-Guest Management Appliance (FMA) head
end device (Example: FMA-LG101). Refer to the Free-
To-Guest (FTG) Device Configuration Application
User Guide and/or the Installation & Configuration Guide
for the FMA device for further information.
• Remote: Configure all LP645H TVs at the site using a
Pro:Centric server (Example: PCS150R). Load an FTG
Configuration (.tlx) file on the Pro:Centric server using
the TV E-Z Installation “Configuration” option in the
Pro:Centric server Admin Client. Refer to the Pro:Centric
Server Admin Client User Guide for further information.
206-4232
43
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode of Operation Overview (Cont.)
While the TV is in FTG Mode:
• Users can still access the Installer Menu using an LG Installer Remote; however, all Installer Menu
items will be read-only.
• Any FTG configuration changes must be made using either the FTG File Manager (FTG Mode via CPU) or
the FTG Device Configuration Application (FTG Mode via EBL). FTG Channel Map Configuration and FTG
Installer Menu Configuration Utilities enable you to make changes, respectively, to the FTG Channel Map
and FTG Installer Menu settings as necessary. Based on the initial method used to configure the TV for
FTG Mode operation (via CPU or EBL), all subsequent changes must be transferred to either the TV CPU
or the EBL via a process that is in accordance or compatible with that method (see information on local
configuration in this document or refer to documentation for the head end device/server for information on
remote management).
• If it becomes necessary to restore the TV to Pass-through Mode, there are several options that will enable
you to do so. Refer to Reference section, “Restoring Factory Defaults on the TV(s),” for further information.
Pages 50 to 53 provide overviews of the utilities that comprise the FTG File Manager. Refer to the Free-
To-Guest (FTG) File Manager User Guide for further information on the FTG File Manager. Refer to the
Free-To-Guest (FTG) Device Configuration Application User Guide for information on the FTG
Device Configuration Application.
Determining the TV Operating Mode
To determine the operating mode of the TV, press MENU SETTINGS on the Installer Remote. The menu
displayed depends on the operating mode. See examples below.
If the Function Menu appears, the TV is in a mode (FTG, PPV, etc.) that does not allow the end user to
change the fundamental TV setup. If the TV setup menus appear, the TV is in Pass-through Mode.
ASPECT RATIO
Move
OK
Function Menu
16:9
ABC
Indicates the TV is not in Pass-through
Mode. While the TV is in this mode,
Installer Menu settings can be
accessed as read-only.
Just Scan
Set By Program
4:3
Zoom
TV Setup Menus
TIME
PICTURE
Shows that the TV is in
AUDIO
CHANNEL
INPUT
Pass-through Mode.
LOCK
OPTION
MY MEDIA
44
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode via CPU
Creating an FTG Configuration File using the FTG File Manager
This section describes how to create an FTG Configuration (.tlx) file that can be saved to a USB memory
device. In order to enable Pro:Idiom decryption, it is recommended that you create an FTG Configuration
file using the FTG File Manager.
Before you begin, note the following:
• There is also an option to save (Learn) an FTG Configuration file from a TV, which may be desirable or
required in either of the following situations:
− If you want to save customized TV setup menu settings to the FTG Configuration file (in addition to
the FTG Channel Map and FTG Installer Menu settings).
− If you do not know the RF channels at the site.
See “Learning FTG Configuration from a TV” on page 48 for further information. However, if you use this
option to save an FTG Configuration file, it is still highly recommended that you open the saved FTG
Configuration file in the FTG File Manager to verify the file contents/settings and to enable Pro:Idiom
decryption by marking Encrypted channels using the FTG Channel Map Editor.
The procedure below provides an overview of the steps required to create an FTG Configuration (.tlx)
file. Refer to the Free-To-Guest (FTG) File Manager User Guide for further information. See also FTG
File Manager sample screens on pages 50 to 53.
1. Install (if necessary) and launch the FTG File Manager (v1.1.0 or higher) on the PC that will be used
to create the FTG Configuration (.tlx) file.
2. You have a number of options:
• To view and/or base a new FTG Configuration file on an existing FTG Configuration (.tlx) file, click
the Open button in the TLX File command section of the FTG File Manager main screen, and select
the desired (.tlx) file.
A list of the file’s contents will be displayed in the TLX File Contents window. Either double-click on an
individual item to copy it or click the Copy All button directly above the TLX File Contents window to
automatically copy all the contents of the opened .tlx file to the FTG Configuration List and, if
applicable, TV Setup Menu List. Note, though, that while TV setup menu settings can be included in
the new FTG Configuration file, the TV setup menu settings are not available for editing.
Edit the configuration of the items in the FTG Configuration List as well as the FTG Configuration
List itself and/or the TV Setup Menu List, as necessary, to create a new file. Then, proceed to step 3
when you are ready to continue.
• To open an existing FTG Configuration (.rml) file created in the FTG Device Configuration Application
to use its FTG Channel Map and/or FTG Installer Menu settings, click File and then Open from the
FTG File Manager menu bar, and select/double-click on the desired “.rml” file.
Edit the channels and/or settings as necessary, and then proceed to step 3 when you are ready to
continue.
• Create a new FTG Channel Map using the FTG Channel Map Editor in the FTG Channel Map
Configuration Utility. Up to 600 logical channels can be defined in the FTG Channel Map.
When you are ready to continue, click Configure and then FTG File Manager from the FTG File
Manager menu bar to return to the FTG File Manager main screen, and then proceed to step 3.
(Continued on next page)
206-4232
45
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode via CPU (Cont.)
(Continued from previous page)
Note: To remove an individual item from the FTG Configuration List or the TV Setup Menu List, click on/
highlight the item to be removed, and then click the Remove Item button directly above the applicable
“List” window. To clear both the current FTG Configuration List and TV Setup Menu List contents, click
the Clear button in the List command section of the FTG File Manager main screen.
Note: To clear the current TLX File Contents, click the New button in the TLX File command section of
the FTG File Manager main screen (above the TLX File Contents window).
3. To add an FTG Channel Map to the FTG Configuration List, click
will copy the current mapped channels to the FTG Configuration List.
under FTG Channel Map. This
Note: If you make any change(s) in the FTG Channel Map Configuration Utility to the current data to
be included in the FTG Configuration List, you will need to recopy the FTG Channel Map to the FTG
Configuration List.
4. (Optional) Load default FTG Installer Menu settings for the TV:
• Click the down arrow at the right of the Chassis field in the Installer Menu Templates section of the
FTG File Manager main screen, and select the appropriate chassis (depending on the TV type) from
the drop-down list of available models.
• Click the Load button.
• Use the FTG Installer Menu Configuration Utility to modify settings, if necessary. Then, return to the
FTG File Manager main screen.
5. If you wish to assign a Zone designation for the current FTG Installer Menu settings, click on the down
arrow at the right of the Zone field (below the FTG Installer Menu Settings field), and select the
appropriate Zone (1–8).
Note: See Reference section, “Using the TV Zoning Feature,” for further information on the TV Zoning
feature and setting the TV Zone # in the TV(s).
6. To add FTG Installer Menu settings to the FTG Configuration List, click
under FTG Installer Menu
Settings. This will copy the selected model settings to the FTG Configuration List.
Note: If you make any change(s) in the FTG Installer Menu Configuration Utility to the current data to
be included in the FTG Configuration List, you will need to recopy the FTG Installer Menu settings to
the FTG Configuration List.
Note: At the top of both the FTG Configuration List and TV Setup Menu List windows, an Edit Zone
field enables you to change the Zone assignment for each LP645H Installer Menu and/or TV Setup
Menu profile, if desired. Select/highlight the desired profile, and then click on the down arrow at the
right of the applicable Edit Zone field to select the appropriate Zone.
7. Click the Save button in the List command section of the FTG File Manager main screen to save the
FTG Configuration List and, if present, TV Setup Menu List contents to an FTG Configuration (.tlx) file
on the PC’s hard drive for later use.
In the Save As pop-up window, name the file, and click Save. The default folder path is C:\Program
Files\Zenith\FTG\TLX. Note that the FTG Configuration file will have a “.tlx” file extension.
Note: To remove an individual item from the FTG Configuration List or the TV Setup Menu List before
saving the new file, click on/highlight the item to be removed, and then click the Remove Item button
directly above the applicable window. To clear both the current FTG Configuration List and TV Setup Menu
List contents, click the Clear button in the List command section of the FTG File Manager main screen.
8. Transfer the FTG Configuration (.tlx) file to a USB memory device, and proceed to “Teaching FTG
Configuration to a TV” on the following page to transfer the FTG Configuration file to an LP645H TV.
46
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode via CPU (Cont.)
Teaching FTG Configuration to a TV
This section describes how to “Teach” an FTG Configuration file from a USB memory device to a TV,
using the USB Download Menu. Ensure you have completed the procedure on the previous page to
create the FTG Configuration file before proceeding with the steps below.
Before You Begin
• If the TV EBL is already in FTG Mode, you cannot use this procedure to make changes to the
FTG Channel Map and FTG Installer Menu settings. You must use a direct PC-to-TV connection
as described in Reference section, “FTG Mode via EBL (Local Configuration),” or an FMA head
end device to reconfigure the EBL.
• If the preceding condition applies, but you wish to switch the TV to FTG mode via CPU, refer
to Reference section, “Restoring Factory Defaults on the TV(s),” for further information before
proceeding.
• If the EZ-Manager Wizard appears on the screen when you turn ON the TV, you can complete the
Teaching process via the wizard (see “USB Configuration” on page 17).
• You may also use the LG Smart Install utility to complete this process. See “LG Smart Install Utility”
on pages 18 to 19 for further information.
• If the TV is currently in Pass-through Mode and you intend to use the TV Zoning feature, make
sure to assign a TV Zone # as described in Reference section, “Using the TV Zoning Feature,”
BEFORE continuing with the procedure below.
Teach FTG Configuration
1. Turn ON the Target LP645H TV, and then insert the USB memory device that
USB Download Menu
contains the FTG Configuration file into the TV’s USB IN port.
Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
2. Press MENU SETTINGS on the Installer Remote to display the TV setup
menus (TV is in Pass-through Mode) or the Function Menu (TV is already in
FTG Mode).
Teach To TV (TLX)
3. Use the arrow navigation keys to select/highlight either the Option menu icon
from the TV setup menus or the Lock menu icon from the Function Menu.
Then, press the number “7” key a total of seven times to display the USB
Download Menu.
Previous
OK
Teach To TV (TLX)
xxLP645H-UA00005.TLX
4. Use the Up/Down arrow keys to select Teach To TV (TLX), and then press OK.
5. Use the Up/Down arrow keys to select the FTG Configuration file you want to
install, and then press OK.
Previous
OK
Teaching status will be shown on a progress bar in a new window.
Do NOT remove the USB device until Teaching is complete. When the Teaching
process is complete, the TV will briefly display a “Teaching Completed” window
and then exit the USB Download Menu.
Teach To TV
UPDATING...
Do not unplug!
50%
6. Remove the USB memory device from the Target TV, and verify that the FTG
Configuration is resident on the Target TV.
The Target TV CPU is now in FTG Mode (if it was previously in Pass-through Mode).
Note: After the Teaching process is complete, the TV tunes according to the Start
Channel setting in the Installer Menu. If a Start Channel is specified, the TV will
tune to that channel; otherwise, the TV will tune to the lowest logical channel in the
FTG Channel Map.
206-4232
47
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode via CPU (Cont.)
Learning FTG Configuration from a TV
To ensure that Pro:Idiom decryption is enabled, it is recommended that you create an FTG
Configuration file using the FTG File Manager as described on pages 45 to 46. However, if
necessary, this option enables you to save (Learn) an FTG Configuration file from an LP645H TV
to a USB memory device.
The option to save (Learn) an FTG Configuration file from a TV may be desirable or required in
either of the following situations:
• If you want to save customized TV setup menu settings to the FTG Configuration file (in addition
to the FTG Channel Map and FTG Installer Menu settings).
• If you do not know the RF channels at the site.
Before You Begin
• If the TV is NOT already in FTG Mode, you may need to perform some manual configuration on the
TV before you start this procedure (see “Optional Manual Configuration / TV Setup” on next page).
• If you intend to use the TV Zoning feature, make sure to assign a TV Zone # as described in
Reference section, “Using the TV Zoning Feature,” BEFORE continuing with the procedure below.
Learn FTG Configuration
1. Turn ON the TV, and then insert a USB memory device into the USB IN port on
USB Download Menu
the TV.
2. Press MENU SETTINGS on the Installer Remote to display the TV setup menus
Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
(TV is in Pass-through Mode) or the Function Menu (TV is already in FTG Mode).
3. Use the arrow navigation keys to select/highlight either the Option menu icon
from the TV setup menus or the Lock menu icon from the Function Menu.
Then, press the number “7” key a total of seven times to display the USB
Download Menu.
Teach To TV (TLX)
Learn From TV (TLL)
Learn From TV (TLX)
Previous
OK
4. To gain access to the Learn From TV options in the USB Download Menu, key
in the password used to access the Installer Menu (Example: Press 9-8-7-6).
Learn From TV (TLX)
5. Use the Up/Down arrow keys to select Learn From TV (TLX), and then press
OK.
Select the file name and press OK to start
6. To differentiate this .tlx file from others, you can use the Up/Down arrow keys
to change the last five digits of the filename. Press OK when you are ready to
initiate Learning.
xxLP645H-UA00005.TLX
-
Previous
OK
Learning status will be shown on a progress bar in a new window. Do NOT
remove the USB device until Learning is complete. When the Learning process
is complete, the USB Download Menu will reappear on the screen.
Learn From TV
UPDATING...
7. When Learning is done, press on the Installer Remote to exit the USB
Download Menu, and remove the USB memory device.
25%
Do not unplug!
Note: It is highly recommended that you open this FTG Configuration
file in the FTG File Manager—BEFORE transferring (Teaching) the file to
any TVs—to verify FTG Channel Map and FTG Installer Menu settings
and enable Pro:Idiom decryption by marking Encrypted channels. This
will also enable you to confirm channels and add channel attributes,
labels, etc.
48
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG Mode via CPU (Cont.)
Optional Manual Configuration / TV Setup
The manual configuration procedures below should only be performed if you do not know the RF channels
at the site and need to “Learn” FTG Configuration from an LP645H TV as described on the previous page.
Ensure the TV is in Pass-through Mode before you begin.
Note: These configuration procedures parallel the initial steps required for creating a Master TV Setup.
See also screen examples on pages 30 to 31.
Set Installer Menu Items
These steps provide specific instruction only on the Installer Menu items that should be set on an LP645H
TV. Refer to pages 20 to 28 for detailed information on all Installer Menu items.
1. Turn ON the TV.* Then, use the Installer Remote to access the Installer Menu (see “Accessing the
Installer Menu” on page 20 for further information).
2. Set Installer Menu item 117 FACT DEFAULT to 1 and press OK on the Installer Remote.
This clears all Installer Menu custom settings, the channel lineup, etc. and restores the factory default
settings. The value will change back to 0 after the commercial controller (PTC) has been restored to
factory default condition. This step ensures that the TV Channel Memory will be the active channel lineup.
3. Set Installer Menu item 003 BAND/AFC, as appropriate.
• Broadcast: Set to 0.
• HRC: Set to 2.
• IRC: Set to 3.
• CATV: Set to 1 (default).
4. Set any other Installer Menu items that affect your TV programming network to the required configuration.
For example, enable/disable Aux inputs, set a Start Channel, etc.
5. After you have adjusted all Installer Menu item settings as required, press OK once on the Installer
Remote to save your changes; then, press OK again to exit the menu.
Set Up TV Features
On-screen setup menus control the features of the TV. Press MENU SETTINGS on the Installer Remote
to access the TV setup menus, and then set Channel, Picture, Audio, Time, etc. options to the desired
configurations. In particular, if you intend to use the TV Zoning feature, make sure to assign a TV Zone #
in this TV as described in Reference section, “Using the TV Zoning Feature.”
Run Auto Tuning (Channel Search)
Note: In the FTG Configuration file, Logical Channel numbers will automatically be assigned in ascending
order, starting with 0 (zero), to the Physical Channels from the TV Channel Map.
Note: Pro:Idiom decryption for encrypted channels will not be enabled unless you use the FTG File
Manager to set the channel attributes.
1. Search for all available analog and digital channels: Use the Installer Remote to go to the Channel
Menu, select the Auto Tuning option, and follow the on-screen instructions.
2. Use the Channel Edit option in the Channel Menu to edit the channel lineup, as necessary, to include
free to guest channels only. Add/delete channels per your system requirements.
Once you have completed these procedures, return to “Learning FTG Configuration from a TV” on the
previous page to complete the Learn sequence.
* If the EZ-Manager Wizard appears on the screen when you turn ON the TV, use the arrow keys on the Installer Remote to select Exit
from the Welcome screen and press OK. In the confirmation pop-up window, select OK, and then press OK once more on the Installer
Remote to exit the wizard. Note that in this case, you will not need to perform step 2 because the TV is already in a factory default state.
206-4232
49
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG File Manager Utilities Overview
FTG File Manager Main Screen
The FTG File Manager main screen enables you to compile, modify, and save FTG Configuration (.tlx)
files. It also allows you to assign a Zone designation to each Installer Menu profile, if desired (see
Reference section, “Using the TV Zoning Feature,” for further information).
FTG CONFIGURATION LIST
Data to be saved in FTG
Configuration (.tlx) file.
CLEAR/SAVE
NEW/OPEN
TLX File options.
FTG Configuration
and TV Setup Menu
List options.
Filename of opened FTG
Configuration (.rml) file
created using FTG Device
Configuration Application.
Copy FTG Channel Map
to and from FTG
Configuration List.
Copy FTG Installer Menu
settings to and from FTG
Configuration List. Assign
Zone as applicable.
Load default FTG
Installer Menu for
32/39/42/47/55LP645H
or 60LP645H chassis.
TLX FILE CONTENTS
TV SETUP MENU LIST
Data contained in opened
FTG Configuration (.tlx) file.
Data to be saved in FTG
Configuration file.
Note: The data referenced in the FTG Configuration List is only a snap-
shot of the current FTG Channel Map and FTG Installer Menu settings
when copied to the list. If you make any change(s) to the current data
to be included in the FTG Configuration List, you will need to recopy
Channel Map and Installer Menu settings to the FTG Configuration List.
50
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG File Manager Utilities Overview (Cont.)
FTG Channel Map Configuration Utility
The FTG Channel Map Configuration Utility enables you to create, view, edit, and print a Logical
Channel Map.
PRINT MAP
EDIT/ADD MAP
Click to display a printable
FTG Channel Map Report. The
report can also be exported as
an HTML or Text file.
Click to open the FTG
Channel Map Editor to create
or edit an FTG Channel Map
(see next page).
Filename of opened FTG
Configuration (.rml) file created
using FTG Device Configuration
Application.
206-4232
51
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG File Manager Utilities Overview (Cont.)
FTG Channel Map Editor
The FTG Channel Map Editor shows a single Logical Channel’s data and the FTG Channel Map.
LOGICAL CHANNEL MAPPING
CUSTOM CHANNEL LABELS/ICONS
Enter custom labels and select icons
by name on menu or by number.
SET CHANNEL ATTRIBUTES
Check/select Encrypted, OSD,
or Blank Video.
Select a Logical Channel number. Then,
assign the RF, Major, and Minor channel
numbers to complete the mapping.
ZONE RESTRICTION
Select Zone restriction
for channel. See
Reference section,
“Using the TV Zoning
Feature,” for further
information.
ADD
EXIT
After defining a new
Logical Channel, click to
add channel to the FTG
Channel Map.
Click to exit editor and
return to FTG Channel
Map Configuration Utility.
UPDATE
DELETE
After editing an existing
Click to remove highlighted
Logical Channel’s data,
click to commit the changes
in the FTG Channel Map.
channel from FTG Channel
Map.
52
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
FTG File Manager Utilities Overview (Cont.)
FTG Installer Menu Configuration Utility
CONFIGURATION SETTINGS
Select tabs for categories of Installer
Menu items to set up TV.
Filename of opened FTG Configuration
(.rml) file created using FTG Device
Configuration Application.
Notes:
• The Pro:Centric tab enables you to set up Pro:Centric-specific parameters. Refer to the Free-To-
Guest (FTG) File Manager User Guide for further information.
• LAN and Hospital parameters are not applicable for these TV models.
206-4232
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Remote Jack Pack / TV Connections & Setup
Remote Jack Pack Setup
RJP Available? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item 093
RJP AVAILABLE appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP AVAILABLE
to 1). See Installer Menu detailed descriptions for further information.
093 RJP AVAILABLE
001
TV Connections
Make these connections ONLY after Master TV Setup and TV cloning procedures are
complete.
Refer to the figure below, and connect the RJ-45 Control cable from the RJP cable bundle to the RJP
INTERFACE port on the TV’s rear jack panel. Then, connect HDMI, RGB, and Composite Video/Audio
connectors, as applicable, for the cable bundle.
AUDIO/VIDEO IN
Connect Composite Video/
Audio connectors from RJP
cable bundle. (Composite
Video on legacy RJP only.)
/
DVI IN
..........
ANTENNA/
CABLE IN
..........
1
2
HDMI/DVI IN 1
Connect HDMI connector
from RJP cable bundle.
RESET UPDATE
SPEAKER OUT OPTICAL
LINE OUT AUDIO OUT
AV IN
PTC SERVICE
(SERVICE ONLY)
GAME CONTROL
/MPI
RGB IN (PC)
RJP
RJP
Connect RJ-45
RS-232C IN
TV-LINK
CFG
AUDIO IN (RGB/DVI)
Control cable from
RJP cable bundle.
(SERVICE ONLY)
RGB IN (PC)
Connect RGB connector from RJP
cable bundle (legacy RJP only).
54
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Upgrading TV/PTC Software using a USB Memory Device
Typical Installer Menu Footer
Checking the Software Versions
You can check the software versions of the TV by accessing the Installer
Menu with the Installer Remote (see “Accessing the Installer Menu” on
page 20 for further information).
UPN 000-000-000-000
PTC V1.00.022
ASIC D279
CPU V3.35.00
When you are finished, press OK again to exit the Installer Menu.
PTC Version
CPU Version
Upgrading TV/PTC Software
The following procedure describes how to update TV/PTC software using the
USB Download Menu, though you may also use the new LG Smart Install utility to
upgrade software, if desired. See “LG Smart Install Utility” on pages 18 to 19 for
further information.
Before you begin this procedure, note that the software upgrade files must be
stored in a folder named “LG_DTV” in the root directory of the USB memory
device. Also, ensure the USB device has been formatted with FAT format.
USB Download Menu
Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
Note for TV Software Upgrade only: If the TV detects a later version of software
on the USB device, it will automatically display a dialog from which you can start the
software upgrade immediately. Otherwise, you can close the dialog, and access the
USB Download Menu as described below.
Teach To TV (TLX)
Previous
OK
1. Turn ON the TV, and then insert the USB memory device into the USB IN port
on the TV.
TV Software Update (Expert)
2. Press MENU SETTINGS on the Installer Remote to display the TV setup
menus (TV is in Pass-through Mode) or the Function Menu (TV is not in Pass-
through Mode).
3. Use the arrow navigation keys to select/highlight either the Option menu icon from
the TV setup menus or the Lock menu icon from the Function Menu. Then, press
the number “7” key a total of seven times to display the USB Download Menu.
TV Software Update
4. Use the Up/Down arrow keys to select Upgrade TV Software or Upgrade
LOGO Image Download
PTC Software, as applicable, and press OK.
5. Select the appropriate option(s), depending on the type of upgrade:
• TV Software Upgrade: (See screen samples at right.) Select TV Software
Update from the first TV Software Update window. In the second TV Software
Update window, select/highlight the update file to install and press OK.
TV Software Update (Expert)
[ Current TV Software Version Information ]
EPK : 03.34.00
Note: Do not select Forced Update options unless you have been specifically
instructed to do so or have previous experience with Expert Software Updates.
The following software files are found in the memory card.
Select the file you want to download to this TV
or press EXIT to cancel the update.
• PTC Software Upgrade: In the PTC Software Update window, select/highlight
EPK : 03.35.00
the update file to install and press OK.
[ Forced Update Option ]
SPI Boot
Note: The PTC Software Update window is similar to the second TV Soft-
ware Update window, though there are no Forced Update options. Current
software version information is shown at the top and update files on the USB
device are listed at the bottom of the window.
LOGO Image
xxLP645H_v3_35_USB
The TV will show update completion progress in a new window. Do NOT remove
the USB device until the software upgrade is complete. When a TV or PTC software
upgrade is complete, the TV will reset itself with an automatic restart.
206-4232
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Downloading a Splash Screen using a USB Memory Device
Splash Screen Image File Guidelines
• The splash screen image must be a baseline (not progressive) JPEG.
• The image should be no larger than 1 MB.
• The maximum resolution allowed for a 32LP645H splash screen image is 1360
x 768 pixels (HD).
• The maximum resolution allowed for a 39/42/47/55/60LP645H splash screen
image is 1920 x 1080 pixels (FHD).
• Avoid using special characters, such as ?, -, etc., in the splash screen image
file name.
USB Download Menu
Upgrade TV Software
Upgrade PTC Software
Downloading a Splash Screen Image
Teach To TV (TLL)
The following procedure describes how to download a splash screen image using
Teach To TV (TLX)
the USB Download Menu, though you may also use the new LG Smart Install
utility to download the splash image, if desired. See “LG Smart Install Utility” on
pages 18 to 19 for further information.
Previous
OK
TV Software Update (Expert)
Before you begin this procedure, note that the splash screen image file must be
stored in a folder named “LG_DTV” in the root directory of the USB memory
device. Also, ensure the USB device has been formatted with FAT format.
1. Turn ON the TV, and then insert the USB memory device into the USB IN port
on the TV.
2. Press MENU SETTINGS on the Installer Remote to display the TV setup
menus (TV is in Pass-through Mode) or the Function Menu (TV is not in Pass-
through Mode).
TV Software Update
LOGO Image Download
3. Use the arrow navigation keys to select/highlight either the Option menu icon
from the TV setup menus or the Lock menu icon from the Function Menu.
Then, press the number “7” key a total of seven times to display the USB
Download Menu.
TV Software Update (Expert)
The following software files are found in the memory card.
Select the file you want to download to this TV
or press EXIT to cancel the update.
4. Use the Up/Down arrow keys to select Upgrade TV Software, and then press
OK.
5. Select LOGO Image Download from the first TV Software Update window.
6. In the second TV Software Update window, use the Up/Down arrow keys to
select the image file to download, and then press OK.
The TV will show download completion progress in a new window. Do NOT
remove the USB device until the image download is complete. When the image
download is complete, the TV will reset itself with an automatic restart. Upon the
restart, you should see the new splash screen.
Splash Image 1360 X 768 ProCentric
56
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Power Consumption Settings
The following tables assume that Installer Menu item 118 POWER SAVINGS is set to 3 (default) and
Installer Menu item 099 BACK LIGHTING is set as shown below (default value is 255).
32LP645H
Power
Consumption
(Watts)
39LP645H
Power
Consumption
(Watts)
42LP645H
Power
Consumption
(Watts)
47LP645H
Power
Consumption
(Watts)
Item 099
Back
Lighting
(Static)
Percent
Savings
Percent
Savings
Percent
Savings
Percent
Savings
100
90
80
70
60
50
40
30
20
10
1
64.2
59.8
56.8
54.9
53.0
51.0
48.1
41.9
35.9
29.6
24.5
42.3
39.8
38.0
36.6
35.5
34.0
32.3
28.3
24.6
20.5
17.1
0%
56.1
52.3
49.7
47.4
46.0
43.8
41.4
35.5
30.1
24.2
19.4
0%
0.0%
6.9%
85.9
80.2
76.2
72.8
70.5
67.1
63.1
54.1
45.5
36.1
28.0
0%
6%
7%
7%
10%
14%
16%
20%
24%
33%
42%
52%
60%
11%
15%
18%
22%
26%
37%
46%
57%
65%
11.5%
14.5%
17.4%
20.6%
25.1%
34.7%
44.1%
53.9%
61.8%
11%
15%
18%
22%
27%
37%
47%
58%
67%
32LP645H
39LP645H
42LP645H
47LP645H
Item 099
Back
Lighting
(Dynamic)
Power
Consumption
(Watts)
Power
Consumption
(Watts)
Power
Consumption
(Watts)
Power
Consumption
(Watts)
Percent
Savings
Percent
Savings
Percent
Savings
Percent
Savings
200
190
180
170
160
150
140
130
120
110
101
64.3
59.7
56.8
55.0
53.2
50.9
48.0
41.9
36.0
29.5
24.5
42.6
39.9
38.1
36.5
35.5
34.0
32.3
28.3
24.6
20.5
17.1
0%
56.6
52.7
49.9
47.7
46.3
44.0
41.6
35.6
30.2
24.3
19.4
0%
0.0%
7.2%
86.4
80.5
76.4
73.0
70.6
67.3
63.2
54.2
45.5
36.2
28.1
0%
6%
7%
7%
11%
14%
17%
20%
24%
33%
42%
52%
60%
12%
16%
18%
22%
26%
37%
47%
57%
66%
11.7%
14.5%
17.3%
20.8%
25.3%
34.8%
44.0%
54.1%
61.9%
12%
15%
18%
22%
27%
37%
47%
58%
68%
Note: Values are results of controlled experiments under laboratory conditions.
206-4232
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Power Consumption Settings (Cont.)
55LP645H
Power
Consumption
(Watts)
60LP645H
Power
Consumption
(Watts)
Item 099
Back
Lighting
(Static)
Percent
Savings
Percent
Savings
100
90
80
70
60
50
40
30
20
10
1
95.3
88.9
84.5
81.1
78.7
74.6
70.4
60.3
50.6
40.3
31.2
0%
101.3
98.9
96.9
95.5
94.5
91.9
87.8
74.1
60.5
46.3
34.0
0%
2%
7%
11%
15%
17%
22%
26%
37%
47%
58%
67%
4%
6%
7%
9%
13%
27%
40%
54%
66%
55LP645H
60LP645H
Item 099
Back
Lighting
(Dynamic)
Power
Consumption
(Watts)
Power
Consumption
(Watts)
Percent
Savings
Percent
Savings
200
190
180
170
160
150
140
130
120
110
101
93.7
89.5
84.5
81.2
78.8
74.6
70.4
60.3
50.5
40.3
31.1
0%
101.3
99.1
96.9
95.5
94.5
92.1
88.0
74.2
60.5
46.5
34.1
0%
2%
5%
10%
13%
16%
20%
25%
36%
46%
57%
67%
4%
6%
7%
9%
13%
27%
40%
54%
66%
Note: Values are results of controlled experiments under laboratory conditions.
58
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: TV Aux Input Configuration
ENABLE
MPI DATA
MPI DATA
DATA STATUS
DATA STATUS
TYPE 0x0D
AUX
DIRECT ACCESS
Tuning *
Installer
Menu Item
046 START
AUX SRCE
(Start Aux
Source)
TV
STATUS TYPE
0x41 SOURCES
ENABLED (R/W)
TYPE 0xD2
CURRENT AV
SOURCE (R)
Installer Menu
Function
SOURCE (R)
Installer
Menu
Installer
Menu
Value
Aux
Input
Input
Mode
Enable
Bit
Item 029
Item 029
Item
Value
1
Label
Value
Value
Description
OLD OCV OLD OCV
= 0
= 1
Video1
(Rear)
REAR AUX
EN
131
91
CV
39
91
1
2
Rear Video (Aux)
1
2
0
VIDEO
1
5
DTV
PC
1
2
1
2
0
2
0
2
VIDEO
COMPUTER
VIDEO
HDMI2
ENABLE
132
92
HDMI2
S-Video Rear
DTV
PC
HDMI1/
DVI
HDMI1
ENABLE
Front
133
134
135
93
94
95
35
87
92
3
4
5
3
4
7
3
5
Computer
COMPUTER
REAR RGB
EN
SVGA Rear
Computer
RGB
PC
1
2
COMPUTER
DTV
PC
1
2
0
2
VIDEO
HDMI3
ENABLE
NTSC Rear
Computer
HDMI3
6
COMPUTER
* Use Installer Remote to enter channel number indicated based on OLD OCV Installer Menu setting.
206-4232
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: b-LAN Setup & Overview
The b-LAN module is internal to the TV. It allows hotel/institution head end equipment with b-LAN technology
to communicate, via the institution’s RF distribution system, with the TV for configuration and control.
Installer Menu item 118 POWER SAVINGS controls the power circuitry for both the embedded b-LAN module
and the GAME CONTROL/MPI port. The default value is 3—the b-LAN module is only powered when the TV
is turned ON. See chart below.
TV ON
TV OFF
POWER
SAVINGS
b-LAN & GAME
CONTROL/MPI Port
Power
b-LAN & GAME
CONTROL/MPI Port
Power
1
On
Off
On
On
3 (default)
A b-LAN enabled head end device, such as an LG FMA-LG101, broadcasts over the RF distribution system
to communicate to multiple TVs. When the TV is first installed, it must be turned ON in order for its embedded
b-LAN module to receive communication from the head end device. At this point, if it is desired for the b-LAN
module to always be powered, including while the TV is turned OFF, set Installer Menu item 118 POWER
SAVINGS to 1.
Also, if MPI communication is required for external MPI control, set Installer Menu item 118 POWER SAVINGS
to 1 so that the GAME CONTROL/MPI port circuitry is always powered.
Caution: POWER SAVINGS should NEVER be set to 7. This setting is intended for factory use
only.
60
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: FTG Mode via EBL (Local Configuration)
The following steps outline local FTG configuration of individual TV EBLs using a direct PC-to-TV
connection. Refer to the Free-To-Guest (FTG) Device Configuration Application User Guide for further
information.
Note: If the TV CPU is already in FTG Mode, you cannot use this procedure to make changes to the FTG
Channel Map and FTG Installer Menu settings. Instead, refer to and use the processes described on
pages 45 to 49 to reconfigure the TV CPU.
Note: If the preceding condition applies, but you wish to switch the TV to FTG Mode via EBL, refer to
Reference section, “Restoring Factory Defaults on the TV(s),” for further information before proceeding.
1. Install (if necessary) and launch the FTG Device Configuration Application (v5.4.0 or higher) on the
PC that will be used to configure the EBL.
2. Build an FTG Channel Map using the FTG Channel Map Editor in the FTG Channel Map Configuration
Utility (or, if applicable, open an existing FTG Configuration [.rml] file).
Note: Up to 141 logical channels can be defined in the FTG Channel Map.
3. Connect the PC to the TV-LINK CFG jack on the TV’s rear jack panel using a USB-to-TTL serial cable
(TTL-232R-5V-AJ). If necessary, install the device driver on the PC.
4. Turn ON the TV.
Note: If Installer Menu item 118 POWER SAVINGS is set to 3 (default), the TV must be ON in order
for steps 5 and 6 below to be successful.
5. “Write” the FTG Channel Map to the EBL (switches the EBL from Pass-through Mode to FTG Mode).
Note: After a “Write” of new data, the TV will briefly display a green text banner that shows the EBL
firmware version and release date.
6. “Read” the current FTG Installer Menu settings from the EBL using the FTG Installer Menu Configuration
Utility. If necessary to make changes to Installer Menu items, “Write” them back to the EBL in FTG Mode.
7. Save the FTG Channel Map and FTG Installer Menu settings to an FTG Configuration (.rml) file for
future use.
8. Tune the TV to a logical channel in the FTG Channel Map.
USB-to-TTL Serial Cable
Required for direct PC-to-
TV FTG configuration.
/DVI IN
..........
2
..........
1
RESET UPDATE
SPEAKER OUT OPTICAL
LINE OUT AUDIO OUT
Laptop
PC
PTC SERVICE
(SERVICE ONLY)
GAME CONTROL
/MPI
RJP
TV-LINK
CFG
TV-LINK CFG
Use for direct PC-to-
TV FTG configuration.
206-4232
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Auto Input(s) Sensing Feature
This section provides detailed settings information for Installer Menu item 042 AUTO INPUTS. To disable
auto-sensing for all available Aux inputs, set item 042 to 0. To enable auto-sensing for all available Aux
inputs, set item 042 to 255. For specifications on all other available settings (i.e., settings for individual
inputs), refer to the table on the following page.
Note: When both item 042 AUTO INPUTS and item 041 SIMPLINK EN are enabled in the Installer Menu,
HDMI inputs will be detected by SIMPLINK, but the Auto Input(s) Sensing Feature will not function.
In the Installer Menu, an informational code is displayed at the right of each Auto Inputs value, for example:
xxLP645H PTC INSTALLER MENU
CPU-CTV
AUTO INPUTS Display Code
This example illustrates Installer Menu item 042
042 AUTO INPUTS
241 7654XXX0
value 241, which enables auto-sensing for all avail-
able Aux inputs. The input #s in the display code (7,
6, 5, 4, 0 in this example) identify the enabled Aux
inputs. See table below for a listing of the LP645H
Aux inputs and their corresponding display code
input #s. The table on the following page shows the
display codes for all item 042 values.
UPN 000-000-000-000
PTC V1.00.022
ASIC D279
CPU V3.35.00
Each code consists of eight characters that identify the Aux input(s) for which auto-sensing is enabled.
The following table identifies the Installer Menu display code Input # for each Aux input that is available on
the LP645H TV models. The table also identifies the Installer Menu item associated with each Aux input.
Remember that in order for auto-sensing to be enabled for an input, that input must also be enabled in the
Installer Menu.
Installer Menu
Display Code
Input #
Aux
Input
Installer Menu
Function
Item
0
4
6
7
5
AV1
039
087
035
091
092
REAR AUX EN
REAR RGB EN
HDMI1 ENABLE
HDMI2 ENABLE
HDMI3 ENABLE
RGB
HDMI 1
HDMI 2
HDMI 3
62
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Auto Input(s) Sensing Feature (Cont.)
Inputs
HDMI 1
Item 042
Value
Installer Menu
Display
AV1
RGB
HDMI 2
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
HDMI 3
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
001
016
017
032
033
048
049
064
065
080
081
096
097
112
113
128
129
144
145
160
161
176
177
192
193
208
209
224
225
240
241
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
Enabled
Disabled
Disabled
Enabled
Enabled
Disabled
Disabled
Enabled
Enabled
Disabled
Disabled
Enabled
Enabled
Disabled
Disabled
Enabled
Enabled
Disabled
Disabled
Enabled
Enabled
Disabled
Disabled
Enabled
Enabled
Disabled
Disabled
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
DDDDXXX0
DDD4XXXD
DDD4XXX0
DD5DXXXD
DD5DXXX0
DD54XXXD
DD54XXX0
D6DDXXXD
D6DDXXX0
D6D4XXXD
D6D4XXX0
D65DXXXD
D65DXXX0
D654XXXD
D654XXX0
7DDDXXXD
7DDDXXX0
7DD4XXXD
7DD4XXX0
7D5DXXXD
7D5DXXX0
7D54XXXD
7D54XXX0
76DDXXXD
76DDXXX0
76D4XXXD
76D4XXX0
765DXXXD
765DXXX0
7654XXXD
7654XXX0
X = Aux input source is Disabled or Not Available (i.e., on this TV model)
D = Auto-sensing for input is Disabled
Input # = Auto-sensing for input is Enabled
206-4232
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: RJP Model List & Input Auto-sensing Hierarchy
RJP Legacy Models
• RJP-101M
• RJP-101ML
• RJP-110F
• RJP-110FW
• RJP-110W
• RJP-110WBR
• RJP-110S
• RJP-120G
• RJP-120T
• RJP-201B/202B
RJP Scaler Models
• RJP-201M
• RJP-301B
• RJP-401B
RJP Input Auto-sensing Hierarchy
Priority
1st (Highest)
2nd
Video
Audio
Digital Video In
PC Video In
Video In
Audio In (3.5mm)
Audio In (L/R)
Digital Video In
3rd
64
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Restoring Factory Defaults on the TV(s)
This section describes how to restore factory defaults either on a single TV that is currently in Pass-through
or FTG Mode or on multiple TVs that are currently in FTG Mode.
Note: If the TV(s) is/are currently in FTG Mode, restoring the factory defaults also resets the TV to Pass-
through Mode.
Installer Menu Item 117 FACT DEFAULT
If the TV is currently in Pass-through Mode, you can set Installer Menu item 117 FACT DEFAULT to 1 to
restore the factory defaults and clear the channel lineup, including any assigned channel icons and
custom text labels.
Factory “IN-STOP”
If the TV is currently in FTG Mode, a predefined value for Installer Menu item 117 FACT DEFAULT
enables access to initiate a factory “IN-STOP” process that will restore the TV to Pass-through Mode in
addition to restoring all factory defaults. The “IN-STOP” will also reactivate the EZ-Manager Wizard.
Contact technical support for the required value for Installer Menu item 117 and for additional information
on performing the IN-STOP from the Installer Menu.
Additional FTG Mode via CPU Options
There are two additional options for restoring Pass-through Mode/factory defaults on TVs that are in FTG
Mode via the CPU. The first enables you to restore a single TV to Pass-through Mode, while the second
enables you to restore multiple TVs to Pass-through Mode at one time. However, both options require that
you create a “Zero Mapped Channels” FTG Configuration (.tlx) file, i.e., an FTG Configuration file with no
data. Refer to the Free-To-Guest (FTG) File Manager User Guide for further information.
• Using a USB memory device, “Teach” a “Zero Mapped Channels” FTG Configuration (.tlx) file to the TV.
Refer to “Teaching FTG Configuration to a TV” on page 47 of this document for further information on the
Teaching process.
• If your system uses a Pro:Centric server for remote management/administration, use the Pro:Centric
server Admin Client to load a “Zero Mapped Channels” FTG Configuration (.tlx) file on the Pro:Centric
server. Refer to the Pro:Centric Server Admin Client User Guide for further information.
Additional FTG Mode via EBL Options
There are two additional options for restoring Pass-through Mode/factory defaults on TVs that are in FTG
Mode via the EBL. The first enables you to restore a single TV to Pass-through Mode, while the second
enables you to restore multiple TVs to Pass-through Mode at one time.
Note: While the IN-STOP process described above will clear both the PTC and the CPU, both
options below only clear the PTC. Thus, the current Channel Map and TV setup menu settings
will remain in the CPU after the reset is completed.
• Using a direct PC-to-TV connection, “Write” an unpopulated Channel Map—that is, a Channel Map with 0
(zero) channels—to the TV. Refer to Reference section, “FTG Mode via EBL (Local Configuration),” and/or
the Free-To-Guest (FTG) Device Configuration Application User Guide for further information.
• If your system uses an FMA for remote management/broadcast configuration, configure the FMA
device with an FMA Configuration (.fma) file that only contains a “0 Mapped Channels” FTG Channel Map
to broadcast to the TV EBL(s). Refer to the Free-To-Guest (FTG) Device Configuration Application
User Guide and/or the Installation & Configuration Guide for the FMA device for further information.
206-4232
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Using the TV Zoning Feature
This section describes the TV Zoning feature available with the LP645H model TVs. The TV Zoning
feature enables you to create localized configurations for TVs in selected locations, or “Zones,” within the
installation environment. This feature is primarily intended for use when the TV is configured for FTG Mode
via CPU operation. However, selected elements of TV Zoning (Installer Menu and TV Setup Menu profile
Zone assignments) may also be used with TV cloning processes using a USB memory device / .tlx file.
Refer to the appropriate section(s) below for further information on the TV Zoning feature and how to set the
TV Zone # in a TV that is currently in Pass-through Mode.
Using the TV Zoning Feature with FTG Mode via CPU Configuration
The FTG File Manager may be used to create an FTG Configuration (.tlx) file that contains multiple Zone
assignments. Zones can be designated for multiple Installer Menu and/or TV Setup Menu profiles. Zone
restrictions can also be assigned to individual channels in the FTG Channel Map. Thus, for example, you
may create an FTG Installer Menu and/or TV Setup Menu profile to be downloaded to a TV in a hotel lobby
and also restrict the channels that are available on that TV.
On location, you must set the TV Zone # in all the TVs in a select area, so that the TVs are configured
with corresponding FTG Installer Menu and/or TV Setup Menu settings and/or can omit channels that
have been restricted in the FTG Channel Map (see “Set the TV Zone # in the TV” on the following page
for further information). TV Zone 0 is the default TV Zone #.
The following subsections briefly describe how to assign Zone designations in the FTG File Manager.
Refer to the Free-To-Guest (FTG) File Manager User Guide for further information.
FTG Installer Menu Profile Zone Assignments
The FTG File Manager main screen enables you to assign a Zone designation to each Installer Menu
profile to be included in an FTG Configuration (.tlx) file. For example, you may wish to create one LP645H
Installer Menu profile for a hotel lobby and another LP645H Installer Menu profile for a fitness center,
both of which are different from the FTG Installer Menu profile for standard guest rooms. The TV Zoning
feature enables you to save multiple FTG Installer Menu profiles, each with its own Zone assignment, in
one FTG Configuration (.tlx) file. If each TV in the aforementioned locations has been assigned a TV Zone
# as described in the procedure on the following page or via the EZ-Manager Wizard, the TV(s) will only
download the Installer Menu profile in accordance with its(their) Zone assignment.
In the FTG File Manager main screen, you can also edit the Zone designation for each Installer Menu
profile and/or TV Setup Menu profile already present in the FTG Configuration List and TV Setup Menu
List windows.
Note: See also the FTG File Manager main screen overview on page 50. In addition, note that TV Setup
Menu profiles cannot be created in the FTG File Manager; they must be “Learned” from a TV.
FTG Channel Map Zone Assignments
The FTG Channel Map Editor in the FTG File Manager’s FTG Channel Map Configuration Utility enables
you to assign Zone restrictions to individual channels that may be prohibited or deemed unsuitable for
selected locations. In the FTG Channel Map Editor, one or more Zone restrictions (1–8) may be placed on
each channel that is to be restricted. For example, if you wish to restrict a channel from Zones 2 and 4,
select both “Zone 2” and “Zone 4” in the Zone Restriction section of the FTG Channel Map Editor screen
when defining or editing that channel.
Note: While a channel can be restricted from up to eight Zones, a TV can only ever be in (set for) one
Zone. See also the FTG Channel Map Editor overview on page 52.
66
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Using the TV Zoning Feature (Cont.)
At the same time, keep in mind that the TV Zone designations are not mutually exclusive. That is, you may
opt to configure Zone restrictions for selected channels in the FTG Channel Map, but at the same time, you
can choose to configure all TVs at the site with the same Installer Menu and/or TV Setup Menu settings. For
example, an FTG Configuration (.tlx) file being used to configure the TVs at a site may contain multiple
Installer Menu and TV Setup Menu profiles with different Zone designations, as well as several channels
with Zone restrictions. Each TV configured with the default TV Zone 0 will download only the Installer Menu
and/or TV Setup Menu profile(s) with a Zone 0 designation. If, on the other hand, the TV Zone # is set to 1,
during configuration the TV will first attempt to retrieve Installer Menu and/or TV Setup Menu profiles with a
Zone 1 designation. If none of the Installer Menu and/or TV Setup Menu profiles has a Zone 1 designation,
the TV will download the profile(s) with a Zone 0 designation. For the FTG Channel Map configuration, when
the TV Zone # is set to 0, the TV will ignore any Zone restrictions (1–8) that may be placed on channels in
the FTG Channel Map. However, when the TV Zone # is set to 1, during configuration, the TV will omit any
channels that have been restricted from Zone 1 in the FTG Channel Map.
Using the TV Zoning Feature with Cloning Configuration
A location-specific configuration / .tlx file may be saved (Learned) from an individual TV as part of a Master
TV Setup and then be used during Teaching. For example, if the TV Zone # in the Master TV is set to 3
before Learning is initiated, the Master TV’s Installer Menu and TV Setup Menu profiles will be saved with
the TV Zone 3 assignment when Learning is completed. In order to configure the Target TVs with the Zone 3
Installer Menu and TV Setup Menu profiles Learned from the Master TV, you must set the TV Zone #
accordingly in the Target TVs before transferring (Teaching) the Master TV Setup. See “Set the TV Zone # in
the TV” below. Also, see “Learning / Teaching a Master TV Setup using a USB Memory Device / .tlx File”
on pages 35 to 36 for additional information on the cloning processes. TV Zone 0 is the default TV Zone #.
Set the TV Zone # in the TV
You can set the TV Zone # in the EZ-Manager Wizard (see “EZ-Manager Wizard” on pages 11 to 17) or,
if the TV is in Pass-through Mode, via the TV’s setup menus as described below. Note that the following
procedure can only be performed while the TV is in Pass-through Mode. You will also be able to specify a
Label (North, South, East, West) and Room Number for this TV, if desired.
1. Turn ON the TV.
2. Press MENU SETTINGS on the Installer Remote, and use the arrow navigation keys to select/highlight
the OPTION menu option. Then, press OK.
3. Use the Up/Down arrows to select Zones & Room Number, and then press OK.
4. In the Zone, Label, and Room Number pop-up window, complete the appropriate fields as described
below. Use the Left/Right arrow keys on the Installer Remote to navigate between each of the fields
• TV Zone: Enables you to set a TV Zone # so that the TV can be configured with Installer Menu and/
or TV Setup Menu settings intended only for the assigned Zone. The Installer Menu and/or TV Setup
Menu settings may be provided in a .tlx file to be used either for Teaching (cloning) or FTG Mode via
CPU configuration. If the TV is being configured for FTG Mode via CPU, the TV Zone # setting also
allows the TV to omit channels that have been restricted in the FTG Channel Map. To set a TV Zone,
navigate to the TV Zone field, and use the Up/Down arrow keys to specify a TV Zone # (1–8).
(Continued on next page)
206-4232
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Using the TV Zoning Feature (Cont.)
(Continued from previous page)
• Label: Allows you to select a North, South, East, or West text label for this TV. Use the Up/Down
arrow keys to select the applicable label.
• Room Number: Allows you to specify the number of the room in which the TV is located. You can use
the number keys on the Installer Remote to direct enter a room number. Use the Dash key on the
Installer Remote as necessary to toggle between number and letter characters in the Room Number
field. Also, you can use the Flashback key on the Installer Remote to delete characters in this field.
Note: Use the Left/Right arrow keys on the Installer Remote to navigate between each of the fields.
5. When you have completed the fields as necessary, select OK, and then press OK on the Installer
Remote to close the window and return to the Option Menu.
6. Press MENU SETTINGS to return to TV viewing.
OPTION
Move
OK
• Language
• Caption
: Off
: Off
• Standby Light
• My Media Setting
• Set ID
: 1
• Demo Mode
: Off
• Zone & Room Number
• Eject
Z
Change a room number
Zone, Label, and Room Number
•
•
If creating Zones for Installer Menu settings and/or Channel Mapping, select the appropriate Zone # (0-8)
based on the Zone in which this TV is installed. (See Commercial Mode Setup Guide for more information.)
Select a Label and/or use the alphanumeric keypad on the remote to input the Room Number.
Q.MENU
MARK
INPUT
1
4
7
2
5
8
0
3
6
TV
DVD
Zone
0
Label
Room Number
1
,
f
jl
t
-----
9
H/UM
CC
P
A
G
E
TIMER
DELETE
MUTE
VOL
CH
CHAR/
NUM
DEL
P
O
R
T
A
L
I
N
F
O
GUIDE
OK
68
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: LP645H Rear and Side Jack Panels
HDMI/DVI IN
Connection for HDMI/DVI
output from external device.
OPTICAL AUDIO OUT
Use for amps and home theater systems.
Note: When the TV is OFF, this port is not enabled.
AUDIO/VIDEO IN
Connection for composite audio/
video output from external device.
UPDATE
Restricted to software updates.
RESET
Initiates a hardware reset and
turns the TV OFF.
ANTENNA/CABLE IN
Connect to Antenna/CATV.
/
DVI IN
..........
ANTENNA/
CABLE IN
..........
1
2
RESET UPDATE
SPEAKER OUT OPTICAL
LINE OUT AUDIO OUT
SPEAKER OUT
LINE OUT
3.5 mm jack) Connect
AV IN
PTC SERVICE
(SERVICE ONLY)
(
GAME CONTROL
/MPI
external audio (fixed speaker,
variable speaker, or fixed line
level [amplifier]) equipment.
See Reference section,
“External Stereo Speaker
Setup,” for further information.
RGB IN (PC)
RJP
RS-232C IN
TV-LINK
CFG
AUDIO IN (RGB/DVI)
(SERVICE ONLY)
RGB IN (PC)
Connection for RGB output from PC.
GAME CONTROL/MPI
When the TV/EBL is in Pass-through Mode,
the MPI function enables an external MPI
control device (i.e., clone programmer, VOD/
PPV STB, etc.) to control the TV. Game
Control—EBL in LodgeNet PPV Mode only.
RS-232C (SERVICE ONLY)
Typically used for downloading
software updates, etc.
PTC SERVICE (SERVICE ONLY)
Restricted to PTC service updates.
RJP
Connection for Remote Jack
Pack (RJP) Control cable.
TV-LINK CFG
3.5 mm jack) Use for direct
Side Jack Panel
(
PC-to-TV FTG configuration.
USB IN
Insert USB memory device
for software updates, cloning
purposes, FTG Mode via CPU
configuration, picture/music
entertainment, etc., as applicable.
HDMI
Connection for HDMI output
from external device.
206-4232
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: External Stereo Speaker Setup
The three-contact (left, right, ground) SPEAKER OUT 3.5 mm jack on the LP645H rear panel provides
stereo speaker signal outputs (fixed speaker, variable speaker, or fixed line level [amplifier]) for external
audio equipment. Set Installer Menu item 097 AUDIO OUTPUT as required in accordance with external
audio equipment connected to the TV. Also, refer to the following diagram for pinout details.
Caution: Do NOT plug in a mono connector, as this may damage the TV.
SPEAKER OUT
LINE OUT
3
1
2
1
2
3
LEFT(Tip)
RIGHT(Ring)
GROUND (Sleeve)
70
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference: Installer Remote Control Typical Key Functions
The LG Installer Remote is supplied with and dedicated to operate the TV. The LG Installer Remote illustrated
below shows typical remote control functions and is provided for reference only. This Installer Remote may vary
from the Installer Remote supplied with the TV.
Q.MENU
(POWER)
Turns the TV ON or OFF
TV/DVD
Select the remote’s operating mode:
TV or DVD.
INPUT
TV
DVD
MARK
INPUT
NUMBER Buttons (0 - 9) & DASH
Use to enter a channel or program number.
Dash is used for sub-channel numbers such
as 2-1, 2-2, etc.
Displays available Aux inputs.
(Q. MENU/MARK options N/A for these TV
models)
@
.,;
abc
def
1
4
7
2
3
FLASHBK (FLASHBACK)
Returns to the previously tuned channel or
input.
ghi
jkl
mno
5
8
0
6
9
Arrows (Up/Down/Left/Right) & OK/ENTER
Use to navigate on-screen menus, direct tune
channels, and adjust TV settings.
pqrs
tuv
wxyz
FLASHBK
MENU SETTINGS
Displays and removes the TV setup menus (or, if
applicable, the Function Menu).
VOLUME UP/DOWN
Increases/decreases sound level.
CHAR/NUM
CC
CC
PORTAL
Activates subtitles.
P
A
G
E
Displays and removes the Pro:Centric interactive
menu.
TIMER
DELETE
MUTE
VOL
CH
TIMER
Sets the amount of time before the TV
automatically turns itself OFF.
INFO
Displays channel information.
MUTE
GUIDE
PORTAL INFO
GUIDE
Switches sound ON or OFF.
Displays and removes the Pro:Centric channel
guide/EPG.
CHANNEL/PAGE UP/DOWN
Changes channels based on channels in
the channel lineup. Moves to previous or
next screen in Pro:Centric channel guide.
(RETURN)
Returns one level to the previous menu/
display.
OK
ENTER
EXIT
Clears all on-screen displays and returns to TV
viewing.
DVD/USB buttons
Use to control DVD player or view USB
memory device content.
MENU
SETTINGS
EXIT
Color buttons access special functions
in some menus.
Accesses the AV devices connected to the
HDMI ports of the TV. Opens the SIMPLINK
Menu (when Installer Menu item 041
SIMPLINK EN is set to 2 or 3).
(PIP/SWAP options N/A for these TV models)
PIP
PIPCH+ PIPCH
PIP INPUT
SAP
-
SAP
Analog Mode: Selects MTS sound (Mono,
Stereo, or SAP). DTV Mode: Changes audio
language, if additional languages are
available.*
SWAP
* SAP notes:
• If SAP is selected and no SAP is provided, sound
may not be heard on channel.
• Each analog channel may have its own SAP setting.
• Digital channels will reset to default audio language
when TV is turned Off/On.
206-4232
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
General Troubleshooting
Some Quick and Easy Tips for Resolving Problems
Installation
Symptom
Possible Cause(s)
Possible Solution(s)
Cannot direct enter
channel number.
(TV in Pass-through Mode) Installer
Menu item 028 CH. OVERIDE is set to
If Installer Menu item 028 CH. OVERIDE is set to 0, only
channels that are active in the TV’s channel lineup can be
0, i.e., disabled (recommended setting). selected. Set CH. OVERIDE to 1 to allow access for direct
keypad entry to all channels.
(TV in FTG Mode) The channel entered Channel access is restricted to channels included in the FTG
is not part of the FTG Channel Map.
Channel Map. If necessary, make changes to the FTG
Channel Map using the FTG File Manager or the FTG Device
Configuration Application, as appropriate.
Picture Reception and Sound
Symptom
Possible Cause(s)
Possible Solution(s)
No picture.
TV is turned OFF.
• Turn TV ON.
• Power failure?
Antenna/cable not connected.
Connections incorrect.
MPI not connected.
Encrypted program.
Wrong tuning band.
Audio muted.
Connect antenna/cable signal to TV.
Check connections on TV.
If applicable, connect MPI cable to MPI device.
Try another channel.
Adjust Installer Menu settings.
Normal picture,
poor or no sound.
Press MUTE or use Volume Up key to increase sound level.
Try a different channel.
Broadcast problem.
Erratic Operation
Symptom
Possible Cause(s)
Possible Solution(s)
Installer Menu setup.
Wrong Installer Menu settings.
Adjust Installer Menu settings as required.
Installer Remote
Symptom
Possible Cause(s)
Possible Solution(s)
Remote doesn’t work.
Remote not in TV Mode.
Not aimed at IR remote sensor.
Remote too far from IR sensor.
MPI not connected.
Use MODE key to select “TV”; puts remote into TV Mode.
Point remote at IR receiver on TV.
Move remote closer to IR receiver on TV or darken room.
If applicable, connect MPI cable to MPI device.
Remove obstructions.
IR path to TV’s receiver obstructed.
Weak batteries.
Replace batteries.
Wrong battery polarity.
Too much light in room.
Wrong Installer Remote.
Check that “+” and “-” match in battery compartment.
Dim room light.
Requires compatible Installer Remote. Contact your LG dealer.
72
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Cont.)
Commercial Mode Check / FTG Operation Troubleshooting
Commercial Mode Check
Use this flowchart to determine whether the TV is currently in Commercial Mode.
Press POWER on
Installer Remote.
TV
connected
to AC
Power?
No
No
Plug into AC
Power outlet.
TV turned
ON?
Yes
Yes
Bad
TV
Leave the TV set ON,
and press MENU on the
Installer Remote.
On-screen
menu display
no longer
Function
Menu
on display?
TV is not in Commercial
Mode. Call Technical
Support for assistance.
Press MENU repeatedly
as if to access the
Installer Menu.
No
No
toggles?
Yes
Yes
TV is in
TV is in
Commercial Mode.
Commercial Mode.
FTG Operation Troubleshooting
The following table provides troubleshooting information for when the EBL is configured for FTG Mode operation.
Symptom
Possible Cause(s)
Cable(s) not connected.
TV not powered.
Solution(s)
Communication Error
(“Communications
Timeout”)
Check and connect communication cables.
Check/connect the TV power cord.
TV not turned ON.
TV needs to be turned ON (default setting of Installer Menu
item 118 POWER SAVINGS).
Wrong COM
(communication) port.
In the FTG Device Configuration Application, select the
correct COM port for the cable being used.
206-4232
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Cont.)
Clone Programmer Troubleshooting
Caution: If the TV is in
Reset Clone Programmer After Static Shock
LodgeNet PPV Mode or FTG
Mode via EBL (check with the
site administrator if you are
not certain), do not connect
a clone programmer to the
GAME CONTROL/MPI port,
as this will damage the clone
programmer.
After replacing exhausted batteries (LT2002 only), or if the clone programmer
behaves strangely after a static shock:
• TLL-1100A: Turn the TLL-1100A OFF and then ON.
• LT2002: Use a paper clip or similar instrument inserted through the small hole
marked RESET to activate the internal reset switch and restore normal operation.
After a reset, check the real-time clock setting. It may be necessary to set the
clone programmer clock from a TV containing the correct time.
Note: Both the Master and Target TVs must be in Pass-through Mode for cloning
purposes. See also IMPORTANT CLONING INFORMATION on page 34.
Clone Programmer
Symptom
Possible Cause(s)
Possible Solution(s)
Clone copies setup in less
than 30 seconds.
Not enough time to copy entire
TV setup.
TLL-1100A: Turn the TLL-1100A OFF and then ON.
LT2002: Press RESET on clone programmer.
Then redo Learn/Teach. (Learning usually takes about 90 seconds;
Teaching usually takes 3 to 4 minutes.)
Remote does not operate
clone programmer.
Wrong Installer Remote.
Only use an LG Installer Remote to operate clone programmer
with TV.
Clone menu does not dis-
play on TV screen, TLL-
1100A shows error mes-
sage, or LT2002 LED does
not blink.
MPI cable not connected.
TV not turned ON.
Connect MPI cable properly, and ensure good connection.
TV must be turned ON for clone programmer to work.
Install four (4) fresh AA high-quality alkaline batteries.
Ensure the TLL-1100A is fully charged or connected to AC power.
(LT2002 only) Weak batteries.
(TLL-1100A only) No charge.
Clone menu hard to read.
No time set.
Weak signal.
Connect TV to a reliable analog channel signal source.
Set time on a TV, and copy time to clone programmer.
Time not available.
Clone programmer problem.
Clone not working.
• Try a different clone programmer.
• Reset the clone programmer.
Clone scans channels
more than once.
Clone should only scan channels Ensure TV is set up correctly, and try cloning again.
once.
Master and Target TVs
Symptom
Possible Cause(s)
Possible Solution(s)
Cloning did not work.
Procedure interrupted.
Wait until procedure complete message is displayed.
Different TV models.
Cloning is only possible with identical model TVs.
Step(s) omitted or not performed. Refer to the applicable cloning procedure(s), and make sure all
tasks were performed.
(LT2002 only) Clone time
disappeared.
Batteries were removed.
Batteries must remain installed to retain time settings.
New setup not present.
Target TV not reset.
Disconnect Target TV from AC power for 15 seconds.
• After cloning operations are complete, unplug the TLL-1100A/LT2002 from the TV.
• If the TV does not display a picture (blank screen) after a few seconds, just change channels.
74
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary of Terms
b-LAN
LodgeNet Interactive Corporation propri-
FTG Mode
Physical Channel Number
LG commercial TV mode that enables
Pro:Idiom decryption and logical channel
mapping. Implementation and TV operation
is based on the “owner” of the FTG Logical
Channel Map—the CPU or the EBL. LG’s
proprietary PC software is required for
configuration.
The major channel number assigned to
represent a specific 6 MHz RF band as
specified by either the broadcast or CATV
channel plan. See CEA (formerly EIA) or
NCTA specifications for further information.
etary RF communication system used to
configure/control TV via RF distribution
system.
Channel Map
Typically refers to a logical channel mapping
of physical channels. This allows digital
channels, like analog channels, to be tuned
without requiring the dash key. Also, chan-
nels (analog or digital) can be arranged in
any order that seems logical for customer
tuning/viewing.
Pro:Centric Application
LG content delivery and communication
interface that provides interactive entertain-
ment, weather, amenities, etc. information
for end users. (Powered by Pro:Centric
server.)
Function Menu
Available via Installer Remote “MENU” key.
Indicates the TV is not in Pass-through
Mode. Restricts menu options to a subset
of the TV setup menus, allowing users to
retain functional control, while disabling
setup options.
Pro:Centric Admin Client
Channel Lineup
Channels set in the TV memory, via Auto
Tuning/manual editing or FTG configuration. Installer Menu
Defines commercial TV functionality based
Web editor/content wizard provided for
service provider and customer configuration
of Pro:Centric application elements.
Cloning
The process of capturing a Master TV
Setup and transferring it to a Target TV.
May be accomplished using either a USB
memory device (available on select mod-
els) or clone programmer.
Pro:Idiom
on the parameters set.
Zenith proprietary security software that
unlocks access to premium content to help
assure rapid, broad deployment of HDTV
and other high-value digital content.
LG Free-To-Guest (FTG)
Refers to a particular commercial mode of
operation within an LG TV. See also FTG
Mode.
PTC
Clone Programmer
Protocol Translator Card. The commercial
controller (microprocessor) of the com-
mercial TV.
Logical Channel Number
A number assigned to either a physical or
virtual channel number in a Logical Chan-
nel Map.
An accessory device (sold separately),
such as the TLL-1100A or LT2002, used
to transfer the Master TV Setup from the
Master TV to the Target TV.
Target TV
A TV to which a Master TV Setup will be
Major Channel Number
Commercial Mode
transferred.
Typically, the RF channel number assigned
A mode of operation that provides a broad
range of commercial TV features based on
control (settings) provided by the PTC and/
or an MPI control device.
to a digital video stream.
TV Setup Menus
Available via Installer Remote “MENU” key
in Pass-through Mode only. Menus provide
access to setup and functional features of
the TV.
Master TV
A TV whose Channel Map and Installer
Menu and TV setup menu settings have
been configured as a Master TV Setup for
cloning purposes.
CPU
The TV’s Central Processing Unit.
Responsible for the presentation of video
and audio from content received via the
TV’s tuner or Aux inputs.
USB Memory Device
A USB flash drive or USB storage device,
etc. that can be used for TV configuration
purposes (typically cloning or FTG Mode
via CPU configuration) or for updating TV
software.
Minor Channel Number
A sub-channel or program number as-
signed to the content embedded in the
digital video stream.
EBL
Embedded b-LAN module. See also b-LAN.
MPI
E-Z Installation
Virtual Channel Number
Multiple Protocol Interface. An MPI port
or, for some TV models, an MPI card slot
provides external control options for solu-
tion providers.
Enables splash screen image and TV
configuration and firmware file downloads
to selected TV models from a Pro:Centric
server. Managed and administered via the
Pro:Centric Admin Client.
An alias (virtual) channel number provided
in the data stream, by the broadcaster, of a
digital broadcast channel to be displayed
by consumer TVs in place of the physical
channel number. The major number is the
same as the original analog channel
number and the minor number is the nth
program available in that digital video
stream.
Pass-through Mode
The TV’s factory default mode of operation.
TVs can be configured for stand-alone use
or as Master TVs for cloning purposes,
and/or TVs may be controlled externally in
this mode.
EZ-Manager Wizard
Lodging model TV configuration wizard
that provides configuration options for
Pro:Centric operation as well as an option
for using a USB memory device to
configure a TV.
206-4232
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Document Revision History / Open Source Software Notice
Document Revision History
Date
Description
May 2013
August 2013
Revision A: New document
Revision B: 55/60LP645H, EZ-Manager, TV Zoning updates
Open Source Software Notice
To obtain the source code under GPL, LGPL, MPL and other open source licenses that are contained in this product, please
notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering
the cost of performing such distribution (such as the cost of media, shipping and handling) upon e-mail request to opensource@
lge.com. This offer is valid for three (3) years from the date on which you purchased the product.
76
206-4232
Download from Www.Somanuals.com. All Manuals Search And Download.
For Customer Support/Service, please call:
1-888-865-3026
Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric is a registered
trademark of LG Electronics Inc. b-LAN is a trademark of LodgeNet Interactive Corporation.
All other trademarks or registered trademarks are the property of their respective owners.
206-4232
© Copyright 2013 LG Electronics U.S.A., Inc.
Revision B
Download from Www.Somanuals.com. All Manuals Search And Download.
|