Domino
user guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Although the SAR is determined at the highest certified power
level, the actual SAR level of the phone while operating can be
well below the maximum value. This is because the phone is
designed to operate at multiple power levels so as to use only
the power required to reach the network. In general, the closer
you are to a wireless base station antenna, the lower the power
output.
could void the warranty and user’s authority to operate the
equipment.
Optimize your Phone’s Performance
Use the instructions in this guide to learn how to optimize the
performance and life of your phone and battery.
Air Bags
Before a phone model is available for sale to the public, it must
be tested and certified to the FCC that it does not exceed the
limit established by the government-adopted requirement for
safe exposure. The tests are performed in positions and
locations (e.g., at the ear and worn on the body) as required by
the FCC for each model.
If you have an air bag, DO NOT place installed or portable
phone equipment or other objects over the air bag or in the air
bag deployment area. If equipment is not properly installed, you
and your passengers risk serious injury.
Medical devices
Pacemakers—Warning to pacemaker wearers: Wireless
phones, when in the ‘on’ position, have been shown to interfere
with pacemakers. The phone should be kept at least six (6)
inches away from the pacemaker to reduce risk.
Body-worn measurements differ among phone models,
depending upon availability of accessories and FCC
requirements. While there may be differences between the SAR
levels of various phones and at various positions, they all meet
the government requirement for safe exposure.
The Health Industry Manufacturers Association and the wireless
technology research community recommend that you follow
these guidelines to minimize the potential for interference.
The FCC has granted an Equipment Authorization for this model
phone with all reported SAR levels evaluated as in compliance
with the FCC RF emission guidelines. SAR information on this
model phone is on file with the FCC and can be found under the
the FCC ID: OVF-K33BIC05 (non-Bluetooth) or OVF-K33BIC06
(Bluetooth).
•
Always keep the phone at least six inches (15 centimeters)
away from your pacemaker when the phone is turned on.
•
•
•
Do not carry your phone near your heart.
Use the ear opposite the pacemaker.
If you have any reason to suspect that interference is taking
place, turn off your phone immediately.
Additional information on SAR can be found on the Cellular
Telecommunications and Internet Association (CTIA) web-site at
Hearing aids—Some digital wireless phones may interfere with
hearing aids. In the event of such interference, you may want to
consult your service provider or call the customer service line to
discuss alternatives.
www.ctia.org
.
* In the United States and Canada, the SAR limit for mobile
phones used by the public is 1.6 watts/kg (W/kg) averaged over
one gram of tissue. The standard incorporates a substantial
margin of safety to give additional protection for the public and to
account for any variations in measurements.
Other medical devices—If you use any other personal medical
device, consult the manufacturer of the device to determine if it
is adequately shielded from external RF energy. Your physician
may be able to help you obtain this information.
Caution
The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance
In health care facilities—Turn your phone off in health care
facilities when instructed. Hospitals and health care facilities
may be using equipment that is sensitive to external RF energy.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
3
Potentially unsafe areas
Keep your phone dry
Posted facilities—Turn your phone off in any facility when
posted notices require you to do so.
Keep the phone dry. Damage can result if the phone gets wet.
Water damage is not covered under warranty.
Aircraft—FCC regulations prohibit using your phone on a plane
that is in the air. Turn your phone off or switch it to Airplane
Mode before boarding aircraft.
Resetting the phone
If the screen seems frozen and the keypad does not respond to
keypresses, reset the phone by completing the following steps:
Vehicles—RF signals may affect improperly installed or
inadequately shielded electronic systems in motor vehicles.
Check with the manufacturer of the device to determine if it is
adequately shielded from external RF energy.
1. Remove the battery cover.
2. Remove and replace the battery.
If the problem persists, return the phone to the dealer for
service.
Blasting areas—Turn off your phone where blasting is in
progress. Observe restrictions, and follow any regulations or
rules.
Accessories
Use only Kyocera-approved accessories with Kyocera phones.
Use of any unauthorized accessories may be dangerous and will
void the phone warranty if said accessories cause damage or a
defect to the phone.
Potentially explosive atmospheres—Turn off your phone
when you are in any area with a potentially explosive
atmosphere. Obey all signs and instructions. Sparks in such
areas could cause an explosion or fire, resulting in bodily injury
or death. Areas with a potentially explosive atmosphere are
often, but not always, clearly marked.
Radio Frequency (RF) energy
Your telephone is a radio transmitter and receiver. When it is on,
it receives and sends out RF energy. Your service provider’s
network controls the power of the RF signal. This power level
can range from 0.006 to 0.6 watts.
They include:
•
•
•
•
fueling areas such as gas stations
below deck on boats
In August 1996, the U.S. Federal Communications Commission
(FCC) adopted RF exposure guidelines with safety levels for
hand-held wireless phones. These guidelines are consistent with
the safety standards previously set by both U.S. and
transfer or storage facilities for fuel or chemicals
vehicles using liquefied petroleum gas, such as propane or
butane
international standards bodies in the following reports:
•
•
areas where the air contains chemicals or particles such as
grain, dust, or metal powders
•
•
ANSI C95.1 (American National Standards Institute, 1992)
NCRP Report 86 (National Council on Radiation Protection
and Measurements, 1986)
any other area where you would normally be advised to turn
off your vehicle engine
•
ICNIRP (International Commission on Non-Ionizing
Radiation Protection, 1996)
Use with care
Use only in normal position (to ear). Avoid dropping, hitting,
bending, or sitting on the phone.
Your phone complies with the standards set by these reports
and the FCC guidelines.
Avoid magnetic environments
E911 mandates
Keep the phone away from magnets which can cause improper
functioning of the phone.
Where service is available, this handset complies with the Phase
I and Phase II E911 Mandates issued by the FCC.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Hearing Aid Compatibility (HAC) with Mobile
Phones
Kyocera Communications Inc.
Some mobile phones and hearing devices (hearing aids and
cochlear implants), when used together, result in buzzing,
humming, or whining noises detected by the user.
To purchase accessories, visit
Some hearing devices are more immune than others to this
interference noise, and phones also vary in the amount of
interference they generate.
The wireless telephone industry has developed ratings for some
of their mobile phones, to assist hearing device users in finding
phones that may be compatible with their hearing devices. Not
all phones have been rated.
Phones that are rated have the rating on their box or a label on
the box. The ratings are not guarantees and results will vary
depending on the user’s hearing device and hearing loss. If your
hearing device happens to be vulnerable to interference, you
may not be able to use a rated phone successfully. Trying out
the phone with your hearing device is the best way to evaluate it
for your personal needs.
M-Ratings—Phones rated M3 or M4 meet FCC requirements
and are likely to generate less interference to hearing devices
than phones that are not labeled. M4 is the better/higher of the
two ratings.
T-Ratings—Phones rated T3 or T4 meet FCC requirements and
are likely to be more usable with a hearing device’s telecoil (“T
Switch” or “Telephone Switch”) than unrated phones. T4 is the
better/higher of the two ratings. (Note that not all hearing
devices have telecoils in them.)
Hearing devices may also be measured for immunity to this type
of interference. Your hearing device manufacturer or hearing
health professional may help you choose the proper rating for
your mobile phone. The more immune your hearing aid is, the
less likely you are to experience interference noise from mobile
phones.
For more information about hearing aid compatibility, visit the
FCC’s Consumer & Governmental Affairs Bureau Web site at
.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Table of Contents
6
Messaging Menu . . . . . . . . . . . . . . . . . . . .31
Manage Web Alerts . . . . . . . . . . . . . . . . . .40
7
8
9
Access Help for @metro . . . . . . . . . . . . . .45
Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . .48
Convenience. . . . . . . . . . . . . . . . . . . . . . . .49
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Accessories. . . . . . . . . . . . . . . . . . . . . . . . .54
Network . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Security . . . . . . . . . . . . . . . . . . . . . . . . . . .56
4
Recent Calls . . . . . . . . . . . . . . . . . . . . . . 21
Contacts . . . . . . . . . . . . . . . . . . . . . . . . . 24
5
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
7
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Download from Www.Somanuals.com. All Manuals Search And Download.
8
1
Get Started
Charge the Battery
You must have at least a partial charge in the
battery to make or receive calls.
To charge the battery:
Phone Battery
Install the Battery
To install the battery:
1. Hold the phone face
down.
1. Connect the AC
adapter to the
2. Find the notch directly
below the back cover.
It is square. Using your
thumbnail, pry the
cover up from the
bottom to remove.
3. Place the battery in the
battery casing with the
metal contacts facing
toward the top of the
phone. The metal
microUSB jack on the
side of the phone.
2. Plug the adapter into a
wall outlet.
The battery icon in the
upper-right corner of the screen tells you
whether the phone is:
–
–
–
Charging (the icon is animated)
Partially charged
Fully charged
You can safely recharge the battery at any time,
even if it has a partial charge.
Note: Before removing the battery, make sure
the phone is powered off.
contacts of the battery
must make contact
with the metal contacts of the battery
casing.
4. Replace the battery
cover by sliding the
notches into the
openings on the top of
the battery casing.
5. Snap the cover into
place.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
9
•
•
Replace the battery only with another
qualified battery. Use of an unqualified
battery may present a risk of fire,
explosion, leakage, or other hazard. If you
are unsure about whether a replacement
battery is compatible, contact customer
support.
Promptly dispose of used batteries in
accordance with local regulations and
recycle if possible. Do not dispose as
household waste.
Battery Safety Guidelines
•
•
Do not disassemble or open the battery.
Do not crush, bend, deform, puncture, or
shred the battery.
•
•
Do not attempt to insert foreign objects into
the battery.
Do not immerse the battery or expose it to
water or other liquids. Even if a battery
appears to dry out and operate normally,
internal parts can slowly corrode and pose a
safety hazard.
•
•
Supervise all battery usage by children.
Avoid dropping the phone or battery. If the
phone or battery is dropped, especially on a
hard surface, an internal short-circuit can
occur and pose a safety hazard. If you
suspect battery damage, take it to a service
center for inspection.
•
Always keep the battery between 15 °C and
25 °C (59 °F and 77 °F). Do not expose the
battery to extremes of temperature (heat or
cold), fire, or other hazards such as a
cooking surface, iron, or radiator.
Never use any damaged battery.
Only use the battery for its intended phone.
Only use the battery with a qualified
charger. Use of an unqualified battery
charger may present a risk of fire,
explosion, leakage, or other hazard. If you
are unsure about whether a charger is
qualified, contact customer support.
Do not short-circuit the battery or allow
metallic conductive objects—such as keys,
coins, or jewelry—to contact the battery’s
terminals.
•
•
•
•
Improper battery use may result in a fire,
explosion, or other hazard.
Common Causes of Battery Drain
•
•
•
•
Playing games or using the Web.
Taking pictures with the flash on.
Keeping backlighting on.
Operating when far away from a base
station or cell site.
Using data cables or accessories.
Operating when no service is available, or
service is available intermittently.
High earpiece and ringer volume settings.
Repeating sound, vibration, or lighted
alerts.
•
•
•
•
•
Download from Www.Somanuals.com. All Manuals Search And Download.
Phone Battery
10
Phone Overview
Get to Know Your Phone
1. Home screen.
2. Volume key raises or lowers ringer volume.
3. Left softkey selects items that appear on the lower left of
the display. At the home screen, you can select Menu
.
4. Speakerphone key activates the speakerphone and answers
incoming calls.
5. Navigation key scrolls through lists and text entry fields
and accesses the following shortcuts from the home screen.
–
Scroll left or right to highlight an icon on the application
bar.
–
–
Scroll up to go to Contacts > View All
.
Scroll down to go to Messaging
.
6. Send key starts or answers a call. Press once to display the
All Calls list and twice to redial the last number dialed.
7. Keypad for entering numbers, letters, or symbols.
8. * Shift key changes the text mode in text entry. Press and
hold to lock the keypad.
9. Jack for a hands-free headset (sold separately).
10. Jack for AC adapter (included) and microUSB cable (sold
separately).
11. Right softkey selects items that appear on the lower right of the display. At the home screen,
you can select @metro
.
12. OK key selects a menu item or option. At the home screen, press the OK key to launch the
icon highlighted on the application bar. Use the Navigation key to choose an icon to highlight.
13. Back key erases characters in text entry and returns you to the previous screen when
navigating through menus.
14. End key turns the phone on and off, ends a call or browser session, and returns you to the
home screen.
15. # Space key enters a space during text entry. Press and hold to activate or deactivate vibrate
mode.
16. 0 Next key cycles through word choices during text entry.
Warning: Inserting an accessory into the incorrect jack will damage the phone.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
11
MetroPCS Applications
At the home screen, your phone diplays an application bar. Scroll left or right to with the
Navigation key to highlight an application. Press the OK key to launch an application. Your
phone has the following application shortcuts available.
MyMetro
Check your account status.
Launch the web browser.
Find a phone number.
Check the news.
MetroWEB
Metro411
Pocket Express
MetroBACKUP
Mobile IM
Back up your data.
Send instant messags.
Send email messages.
mail@metro
Note: Please check with your service provider regarding the pricing and availability of these
applications.
Download from Www.Somanuals.com. All Manuals Search And Download.
Phone Overview
12
Screen Icons
These icons may appear on your phone’s screen.
The phone has a high speed data connection.
A call is in progress.
The phone is operating in IS2000 (1X)
digital mode.
The phone is set to light up instead of ring.
New message.
The phone is in airplane mode.
The alarm clock is set.
New email message.
The phone is set to auto answer.
New email and instant message.
New instant message.
The battery is fully charged. The more black
bars, the greater the charge.
The phone is transferring data with
Bluetooth.
New photo and text message.
New photo and voice message.
New photo message.
A headset or other hands free device is in
operation.
New photo, voice and text message.
New text message.
A headset or other hands free device is
transferring data.
New voice and text message.
New voice message.
Bluetooth wireless technology is disabled
(Off).
Bluetooth wireless technology is enabled
(On).
The phone is not receiving a signal. You
cannot make or receive calls.
The battery will not charge.
The phone is roaming outside of its home
service area.
Data service is available and active on your
phone. Check with your service provider for
availability.
The phone is in privacy mode or is accessing
a secure Web site.
Data service is available, but the phone is
dormant.
The phone is receiving a signal. You can
make and receive calls. Fewer bars indicate a
weaker signal.
(blinking) The phone is receiving high-speed
data.
The speaker phone is turned on.
A T-coil hearing aid is in operation.
A traffic channel is active.
(blinking) The phone is sending high-speed
data.
The phone is operating in IS95 digital mode.
Content is DRM protected.
The phone is in TTY device mode.
The phone is set to vibrate or to vibrate and
then ring.
Position location is set to your service
provider and to emergency services.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
13
Main Menu
Press the OK key when the phone is in idle state to access the main menu.
Idle State >
Menu
Level 1 >
Level 2
Recent Calls
Access these options: All Incoming, Outgoing, Missed,
Erase Call List
,
,
Call Timers, and Kilobyte Counter
.
Contacts
Access these options: View All
,
Add New Metro411,
,
Groups Speed Dial List
,
,
Delete All, and Contacts Count
.
Messaging
Access these options: Inbox New Text Msg New Pic Msg,
,
,
Email IM Voicemail Web Alerts Sent Msgs Outbox
,
,
,
,
,
,
Saved Msgs Drafts Msg Settings Message Groups Erase
,
,
,
,
Msgs, and Message Count
Download an application.
Browse the web.
.
@metro
MetroWEB
Settings
Access these options: Bluetooth
,
Convenience, Display,
Sounds Accessories Network, and Security.
,
,
Media Gallery
Phone Info
Tools
Access these options: Images Tones, and Delete All
Access these options: Build Info and Icon Keys
Access these options: Voice Memo Scheduler Alarm
,
.
.
,
,
,
Clock Tip Calculator Calculator Timer, and Stopwatch.
,
,
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu
14
Guide Conventions
In this guide, the following conventions are
used when describing phone features.
Select means to press the Left softkey, Right
softkey or OK key to select an item seen on the
display. For example, “Select Menu” tells you
to physically press the left softkey to choose
Menu from the display.
Press means to press a phone key. For
example, “Press the Send key to make a phone
call” tells you to physically press the Send key
on your phone.
Scroll means to use the Navigation key to
move through a list on the display. For
example, “Scroll through your contacts list to
choose a contact” means to physically press the
Navigation key up or down to scroll through
the list on the display.
>
(greater than symbol) tells you to select an
option from a menu or list. For example,
Menu Settings” means to:
“
>
1. Press the left softkey to select Menu
.
2. Scroll to the Settings option.
3. Press the OK key to select Settings
.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
15
2
Call Features
This section describes the basic features related
to calls.
Redial a Number
1. Press the Send key to open your call
history.
Power Phone Up
2. Highlight a phone number or contact and
press the Send key.
Note: To redial the last number called,
received or missed, press the Send key twice.
•
To turn your phone on, press the End key
and wait until the phone display lights up.
To turn your phone off, press and hold the
End key until the phone plays a short
musical sound and turns off.
•
Answer Phone Calls
When a call comes in, the phone rings,
vibrates, or lights up. The phone number of the
caller also appears if it is not restricted. If the
number is stored in your contacts list, the
contact’s name appears. There are several ways
you can answer a phone call.
Make Phone Calls
Make sure you are in an area where a signal
can be received. Look for the signal strength
icon on the home screen. The more bars, the
stronger the signal. If there are no bars, move
to where the signal strength is better.
When the phone has been idle for a time, it
cycles into power save mode. Press any key to
return to normal operating mode.
Answer Using Earpiece
Press the Send key.
Answer Using Speakerphone
Press the Speakerphone key.
There are several ways you can make a phone
call.
End Phone Calls
Call Using a Number
1. Enter a phone number.
2. Press the Send key.
Press the End key.
Call Using a Contact
1. From View All, highlight a contact.
2. Press the Send key.
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Phone Up
16
To call a contact that has a speed dial location:
1. Enter the one- or two-digit speed dial
location.
Volume Control
Adjust Volume during a Call
Press the Volume key up or down to adjust the
earpiece volume during a call.
2. Press the Send key.
Emergency Services
Call Emergency Services
Use the Speakerphone
Your phone has a built-in speakerphone.
•
To turn on the speakerphone, press the
Speakerphone key. The speakerphone icon
appears on the home screen when the
speakerphone is on.
You can call an emergency code even if your
phone is locked or your account is restricted.
When you call, your phone enters emergency
mode. This enables the emergency service
exclusive access to your phone to call you
back, if necessary. To make or receive regular
calls after dialing the code, you must exit this
mode.
•
To turn off the speakerphone, press the
Speakerphone key again.
Note: If you press the Speakerphone key
during an incoming call, you will answer the
call.
To dial an emergency code:
1. Enter the 3-digit emergency code.
2. Press the Send key.
Note: Regardless of the 3-digit emergency
code (911, 111, 999, 000, etc.), your phone
operates as described above.
Silence an Incoming Call
•
•
To silence the phone without answering the
call, press the Back key or press the
Volume key up or down.
To silence the phone and answer the call,
press the Back key or press the Volume
key up or down and then press the Send
key.
Exit Emergency Services
When you have completed the emergency call:
1. Select Exit
.
Use Speed Dialing
2. Select Exit again to confirm your choice.
Note: To determine who has access to your
location, see “Set Location Information” on
Speed dialing allows you to assign a one- or
two-digit shortcut to a contact. Before you can
use speed dialing you must save a phone
number as a contact and assign a speed dial
location to it. See “Assign Speed Dials to
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
17
3
Text Entry
You can enter letters, numbers, and symbols in
contacts, text messages, and your banner.
Enter Numbers with Number Keypad
From the text entry field, select Options >
Numbers Only to enter a number when you
press a key once.
Text Entry Modes
The text entry screen has the following
features:
The
icon indicates you are in Numbers
Only input mode. Press and hold the * Shift
key to switch input modes.
1. Characters remaining
that you can type.
Allowed message
length can vary
depending on your
Enter Letters with Number Keypad
From the text entry field, select Options >
Normal Alpha to enter letters. You can enter
text in the following ways:
service.
•
To enter a letter, press a key once for the
first letter, twice of the second letter, and so
on. If your phone is set to Spanish,
accented letters are available. Wait for the
cursor to move right and enter the next
character. Press the # Space to enter a
space.
2. Text entry fields.
3. Current capitalization setting.
4. Current text entry mode.
Note: The entry mode will default depending
on the task you are doing. For example, when
entering a phone number, you are in Numbers
Only mode. When entering a name for a
contact, you are in Normal Alpha mode.
•
•
To change case mode for a single letter,
press that key until you see the letter case
you want. To change the case mode, press
the * Shift key.
To enter a number, press and hold a number
key until the number appears on the screen.
The
icon indicates you are in Normal
Alpha input mode. Press and hold the * Shift
key to switch input modes.
Download from Www.Somanuals.com. All Manuals Search And Download.
Text Entry Modes
18
Rapid Entry with Number Keypad
From the text entry field, select Options >
Rapid Entry to check words you are trying to
spell against a dictionary of common words.
You can enter text in the following ways:
•
To enter words, press a key once. For
example, to enter the word “Glow” press
the 4 > 5 > 6 keys. If the word doesn’t
match what you want, press 0 Next key to
look at other word matches. When you see
the word you want, scroll right.
•
•
To change case mode, press the * Shift key.
To enter a number, press and hold a number
key until the number appears on the screen.
The
icon indicates you are in Rapid Entry
input mode. Press and hold the * Shift input
key to switch input modes.
Enter Symbols with Number Keypad
While entering text in Normal Alpha mode,
you can enter symbols by pressing the key
1
until you see the symbol you want. Using this
method, you have access to the following
symbols:
. @ ? ! - , & : ‘
To access the full set of symbols:
1. From the text entry field, select Options
Add Symbols
>
.
2. Scroll up or down to view the list of
symbols.
3. Press the number key corresponding to the
symbols to enter it.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
19
Text Entry Quick Reference
This table gives instructions for entering letters, numbers, and symbols.
To...
Do this...
Enter a letter
Use Normal Alpha mode and press a key until you see the
letter your want.
Enter a number
Enter a symbol
Use Numbers Only mode and press a key.
Use Normal Alpha mode and press the key until you see
1
the symbol you want.
Enter a space
Press the # Space key.
Press the Back key.
Erase a character
Erase all characters
Move the cursor right or left
Move the cursor up or down
Change input mode
Change case mode
Press and hold the Back key.
Scroll left or right.
Scroll up or down.
Press and hold the * Shift key.
Press the * Shift key.
Capitalize any letter
In Normal Alpha mode, press the * Shift key. Choose
uppercase.
Lowercase any letter
In Normal Alpha mode, press the * Shift key. Choose
lowercase.
Initial caps
In Normal Alpha mode, press the * Shift key. Choose
sentence case.
Select options on the bottom of the screen
Press the appropriate left or right softkey.
Download from Www.Somanuals.com. All Manuals Search And Download.
Text Entry Quick Reference
20
4
Recent Calls
Recent Calls Menu
Select Recent Calls from the main menu to access the following functions:
Level 1 >
Level 2 >
Level 3
Recent Calls
All
See a list of all voice calls.
Incoming
Outgoing
Missed
See a list of all voice calls you have received.
See a list of all voice calls you have made.
See a list of all voice calls you have missed.
Erase Call List
Call Timers
Kilobyte Counter
Access these options: All
,
Incoming
,
Outgoing, and Missed
.
Access these options: All Voice Calls
,
All Data Calls, and Life
.
See how much data you have sent and received.
Return an Outgoing Call
Work with Call Lists
Return Any Call
1. From All, highlight a number.
2. Press the Send key to call the number or
select Options to access more features.
This list contains all calls made and received.
1. From Outgoing, highlight a number.
2. Press the Send key to call the number or
select Options to access more features.
This list contains all calls you have made.
Return a Missed Call
1. From Missed, highlight a number.
2. Press the Send key to call the number or
select Options to access more features.
This list contains all calls you received, but did
not answer.
Return a Received Call
1. From Incoming, highlight a number.
2. Press the Send key to call the number or
select Options to access more features.
This list contains all calls received.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
21
Send Multimedia Message from Call List
1. At a call list, highlight a contact.
Manage a Missed Call Alert
When you have missed a call, “Missed Call”
appears on your screen. You can do one of the
following:
2. Select Options > Send Pic Msg
3. Complete your multimedia message and
select Send
.
•
•
To clear the screen, select OK.
To view the call details, select Calls and
press the OK key.
.
Erase Call List Records
•
To return the call, select Calls and press the
Send key.
Erase a Single Record
1. At a call list, highlight a contact.
2. Select Options > Erase Record > Yes
Call List Options
.
Save Number from Call List
1. At a call list, highlight a number.
Erase a Call List
From Erase Call List, select a call list to erase
records from. For example to erase all records
from the incoming call list, select Incoming >
2. Select Options > Save
.
3. Select Save New Contact to create a new
contact or Add to Existing to add a number
to an existing contact.
Yes
.
Erase All Call Lists
View Contact from Call List
From Erase Call List, select All > Yes to erase
all records from all call lists.
1. At a call list, highlight a contact.
2. Select Options > View to see the contact
details screen.
Work with Call Timers
View Outgoing Calls Timer
From All Voice Calls, select Total Dialed to
view the number of calls and the total call time.
Select Done when finished.
This timer tracks all calls made since you last
reset the timer. To reset this timer to zero,
Send Text Message from Call List
1. At a call list, highlight a contact.
2. Select Options > Send Text Msg
3. Complete your text message and select
Send
.
.
select Reset > Yes
.
Download from Www.Somanuals.com. All Manuals Search And Download.
Erase Call List Records
22
View Incoming Calls Timer
View All Data Timer
From All Voice Calls, select Total Received to
view the number of calls and the total call time.
Select Done when finished.
From All Data Calls, select All Calls to view
the amount of data sent and received by the
phone since the last reset. Select Done when
finished.
This timer tracks all calls received since you
last reset the timer. To reset this timer to zero,
This timer tracks all calls received since you
last reset the timer. To reset this timer to zero,
select Reset > Yes
.
select Reset > Yes
.
View All Calls Timer
From All Voice Calls, select All Calls to view
the number of calls and the total call time.
Select Done when finished.
This timer tracks all calls received since you
last reset the timer. To reset this timer to zero,
View Calls Life Timer
From Life, select All Voice Calls to view the
number of calls and the total call time. Select
Done when finished.
This timer tracks all calls made and received
for life of the phone and cannot be reset.
select Reset > Yes
.
View Outgoing Data Timer
From All Data Calls, select Total Sent to view
the number of calls and the total call time.
Select Done when finished.
View Data Life Timer
From Life, select All Data Calls to view the
number of calls and the total call time. Select
Done when finished.
This timer tracks all calls made since you last
reset the timer. To reset this timer to zero,
This timer tracks data sent and received for life
of the phone and cannot be reset.
select Reset > Yes
.
View Data Counter
View Incoming Data Timer
Select Kilobyte Counter to view the amount
of kilobytes sent during data calls. Select Done
when finished.
From All Data Calls, select Total Received to
view the number of calls and the total call time.
Select Done when finished.
This timer tracks kilobytes sent during data
calls made, data calls received, and for the life
of the phone. To reset the data counter to zero,
This timer tracks all calls received since you
last reset the timer. To reset this timer to zero,
select Reset > Yes
.
select Options > Reset > Yes
.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
23
5
Contacts
Use Contacts to store information about a person or company.
Contacts Menu
Select Contacts from the main menu to access the following functions:
Level 1 >
Contacts
Level 2 >
Level 3
View All
Access your existing contacts list.
Add a new entry to your contacts list.
Access the Metro411 directory.
View your groups of contacts.
View your contacts assigned with speed dials.
Add New
Metro411
Groups
Speed Dial List
Delete All
Contacts Count
Access options: Contacts Only Groups Only, and Delete All.
,
Check how much contact space you have used.
Launch Metro411
Access Contacts
Access Contacts List
1. From View All, enter the first letter of your
desired contact and scroll to highlight it.
2. Do one of the following:
From Contacts, select Metro411 to access the
Metro411 directory. You may need download
and install Metro411. For more information on
the availability of Metro411, contact
metroPCS.
–
–
Press the Send key to call the contact.
Press the OK key to view the contact’s
details.
–
–
Select New to create a new contact.
Select Options to access more
functions.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contacts Menu
24
View Contact Details
Add Contacts from Contacts Menu
1. From Add New, enter a name for the
contact. Scroll down to the next field when
done.
1. From View All, select a contact.
2. At the contact details screen, highlight a
number, address or note.
2. Enter a primary number for the contact.
3. Enter additional phone numbers, email
addresses, and other contact details. (Scroll
up or down to move through the contact
fields.)
3. Select the detail you want to view. For
example, to view a phone number, select
Options > View Number
.
Use Frequent List
With Frequent List enabled, you can view 15
of your most frequently called contacts. See
4. When done, select Save
.
Add a Code or Extension
When saving the phone number of an
automated service, you may include a pause
for dialing an extension.
1. From the home screen, enter a phone
number.
Use Fast Find
With Fast Find enabled, you can press one or
two keys to view closer matches in your
contacts list. See “Call Contact using Fast
2. Select Options and a type of pause:
–
Time Pause causes the phone to stop
dialing for two seconds.
Hard Pause causes the phone to wait
until you select Release while making
the call.
Add Contacts
Add Contacts from Home Screen
1. From the home screen, enter a phone
number to save (include the area code).
2. Select Save > Save New Contact
3. Enter a name for the contact.
4. Enter additional phone numbers, email
addresses, and other contact details. (Scroll
up or down to move through the contact
fields.)
–
3. Enter the remaining numbers and select
Save > Save New Contact
4. Complete the contact information and
select Save
.
.
.
5. When done, select Save
.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
25
Send a Contact vCard
Use Contacts
Call Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight a
number.
1. From View All, select a contact.
2. At the contact details screen, highlight the
contact name.
3. Select Options > Send as vCard > Via
MMS (to attach to a multimedia message),
or Via Bluetooth (to send to a
Bluetooth-enabled device).
4. Complete the appropriate task to send the
contact information.
3. Select Options > Call
.
Send a Text Message to Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight a
number or email address.
Customize Contacts
Edit Contact Details
1. From View All, select a contact.
3. Select Options > Send Text Msg
4. Complete your text message and select
Send
.
.
2. At the contact details screen, select Edit
3. Enter additional phone numbers, email
.
Send a Multimedia Message to
Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight a
number or email address.
addresses, and other contact details. (Scroll
up or down to move through the contact
fields.)
4. When done, select Save
.
3. Select Options > Send Pic Msg
4. Complete your multimedia message and
select Send
.
Assign Number Types
1. From View All, select a contact.
.
2. At the contact details screen, select Edit
.
3. Press down twice to scroll to the number
type dropdown and press the OK key.
4. Select a number type. The appropriate icon
appears next to the number in your contacts
list.
5. Select Save
.
Download from Www.Somanuals.com. All Manuals Search And Download.
Use Contacts
26
Assign Ringers to Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight the
contact name.
Assign Speed Dials to Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight a
number.
3. Select Options > Ringer > Assign Ringer
and a ringer from the list. (Scroll to play the
ringers.)
3. Select Options > Add Speed Dial.
4. Select a location from the list to assign the
speed dial number.
Assign Message Tones to Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight the
contact name.
3. Select Options > Msg Tone > Assign Msg
Tone and a ringer from the list. (Scroll to
play the ringers.)
Change Primary Numbers
When a contact has more than one number, the
first number becomes the primary number by
default. To change the contact’s primary
number:
1. From View All, select a contact.
2. At the contact details screen, highlight a
number.
Assign Pictures to Contacts
1. From View All, select a contact.
2. At the contact details screen, highlight the
contact name.
3. Select Options > Picture > Assign Picture
to assign a picture.
3. Select Options > Primary Number > Yes
.
Add Contacts to Groups
1. From View All, select a contact.
2. At the contact details screen, highlight a
number or email address.
3. Select Options > Add To Group
.
Add a Prefix to Phone Numbers
Use Prepend to add a prefix, such as an area
code, to a phone number:
1. From View All, select a contact.
2. At the contact details screen, highlight a
number.
4. Select groups from the list provided. A
checkmark appears next to each selection.
You can also remove a checkmark.
5. When finished, select Done
.
3. Select Options > Prepend to enter the
prefix at the beginning of the number.
4. Select Save
.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
27
Visit Web Addresses
Erase All Contacts and Groups
1. From View All, select a contact.
2. At the contact details screen, highlight a
Web address.
From Delete All, select Delete All > Yes > Yes
to erase all your contacts and groups.
Note: You cannot recover deleted information.
3. Select Options > Launch Web
.
Contact Groups
Erase Contacts
Erase Contact Details
1. From View All, select a contact.
2. At the contact details screen, highlight a
number, address or note.
3. Select your desired erase option and then
select Yes. For example, to erase an email
address, select Options > Erase Address >
You can assign your contacts to groups. Your
phone comes with default groups. You can also
create your own groups.
View Groups
1. Select Groups to view your preloaded
groups, followed by the custom groups you
have created.
2. Highlight a group and do one of the
following:
Yes
.
–
Press the OK key to view the group
details.
Erase an Entire Contact
1. From View All, select a contact.
2. At the contact details screen, highlight the
contact name.
–
–
Select New to create a new group.
Select Options to access more
functions.
3. Select Options > Erase Contact > Yes to
erase the entire contact.
Create a New Group
1. From Groups, select New
.
Erase All Contacts
2. Enter a name for the group and select Next
3. Select contacts from the list provided. A
checkmark appears next to each selection.
You can also remove checkmarks.
.
From Delete All, select Contacts Only > Yes
> Yes to erase all your contacts.
Note: You cannot recover deleted information.
4. When finished, select Done
.
Your new group appears the next time you
view your groups list.
Download from Www.Somanuals.com. All Manuals Search And Download.
Erase Contacts
28
Send Text Messages to Groups
Assign Message Tones to Groups
1. From Groups, select a group.
2. At the group details screen, scroll to the
group name.
1. From Groups, highlight a group.
2. Select Options > Send Text Msg
.
3. Complete your text message and select
Send
.
3. Select Options > Msg Tone > Assign Msg
Tone and a ringer from the list. (Scroll to
play the ringers.)
Send Multimedia Messages to Groups
1. From Groups list, highlight a group.
Assign Pictures to Groups
1. From Groups, select a group you have
created.
2. Select Options > Send Pic Msg
3. Complete your multimedia message and
select Send
.
.
2. At the group details screen, scroll to the
group name.
3. Select Options > Picture > Assign Picture
to assign a picture.
Add or Remove Contacts from Groups
1. From Groups, highlight a group.
2. Select Options > Edit
.
3. If you are modifying a group you created,
select Next. Otherwise, go to the next step.
4. Select contacts from the list provided. A
checkmark appears next to each contact in
the group. Press the OK key to add or
remove checkmarks.
Send a Group vCard
1. At the Groups list, highlight a group.
2. Select Options > Send > Via Bluetooth
3. Complete the appropriate task to send the
group information.
.
5. When finished, select Done
.
Assign Ringers to Groups
1. From Groups, select a group.
2. At the group details screen, scroll to the
group name.
3. Select Options > Ringer > Assign Ringer
and a ringer from the list. (Scroll to play the
ringers.)
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
29
Create a Message Group
Speed Dial List
Assign Speed Dial Numbers
1. From Speed Dial List, highlight an
unassigned number (marked as empty).
You can create a group specifically for
messaging, based on a contact group.
1. From Groups, highlight a group.
2. Select Options > Create Msg Group
.
2. Select Assign
.
3. Modify the name for the group and select
Next
3. At the contacts list, select a contact.
4. At the contact details screen, select a phone
number.
.
4. Select contacts from the list provided. A
checkmark appears next to each contact in
the group. Press the OK key to add or
remove checkmarks.
5. When finished, select Done
Your new message group appears the next time
you view your message groups list.
Clear Speed Dial Numbers
1. From Speed Dial List, highlight an
assigned number.
.
2. Select Erase > Yes
.
Check Contacts
Erase a Group
1. From Groups, highlight a group.
Select Contacts Count to check how many
contacts you have stored.
2. Select Options > Erase > Yes
.
Erase All Groups
From Delete All, select Groups Only > Yes >
Yes to erase all your groups.
Note: You cannot recover deleted information
or erase preloaded groups.
Download from Www.Somanuals.com. All Manuals Search And Download.
Speed Dial List
30
6
Messaging
Use Messaging to send, receive, and erase messages from your phone.
Messaging Menu
Select Messaging from the main menu to access the following functions:
Level 1 >
Level 2 >
Inbox
Level 3
Messaging
Shows a list of received text and multimedia messages.
Compose a text message.
New Text Msg
New Pic Msg
Email
Compose a picture message.
Compose an email.
IM
Send an instant message.
Voicemail
Web Alerts
Sent Msgs
Outbox
Shows how many voicemails are waiting.
Shows how many alerts are waiting.
Shows a list of messages you have successfully sent.
Shows a list of messages you have sent, but are pending or failed.
Shows a list of messages you have saved.
Saved Msgs
Drafts
Shows a list of messages that have been started, but saved to be
completed at a later time.
Msg Settings
Access these options: Alerts
QuickText Auto Retrieve
Save to Sent Auto-Erase
Msg Receipt Voicemail Number
,
Msg List View
,
Signature
,
,
,
CC and BCC
,
Callback Number
,
,
,
,
Default Text
,
Text Msg Receipt
,
Pic
,
Erase Recent List
,
Text Msg
Read Receipt, and Pic Msg Reply by
.
Message Groups
Erase Msgs
See a list of your message groups.
Access these options: Inbox
,
Outbox, Sent Msgs, Saved Msgs,
Drafts, and All
.
Message Count
Check how many messages you have.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
31
Create a Multimedia Message
You can only send multimedia messages to
phone numbers capable of receiving them or to
email addresses. If the character and file size
limit for a single multimedia message is
exceeded, the message must be edited to meet
the size limitation.
Note: Multimedia messaging is not available
on all phones. Check with your service
provider.
Send Email
From Messaging, select Email to launch the
email application. For more information on
this application, contact metroPCS.
Send Instant Messages
From Messaging, select IM to launch the
instant message application. For more
information on this application, contact
metroPCS.
1. From New Pic Msg, enter a recipient’s
phone number or email address. (Select
Options to access contacts, groups or
recently used addresses. Scroll down to
move to the next field when done.)
You can message up to ten recipients at
once. Use comma or spaces to separate
addresses.
2. Repeat the first step for CC and BCC, if
needed.
3. Enter a subject.
4. Enter a message.
5. Attach an image file. (Select Options to
access more features.)
Send Messages
Create a Text Message
You can only send text messages to phone
numbers capable of receiving them or to email
addresses if supported.
1. From New Text Msg, enter a recipient’s
phone number or email address. (Select
Options to access contacts, groups or
recently used addresses. Scroll down to
move to the next field when done.)
You can message up to ten recipients at
once. Use comma or spaces to separate
addresses.
6. Attach a sound file. (Select Options to
access more features.)
2. Enter the message. (Select Options to
access more features.)
7. When done, select Send
.
3. When done, select Send
.
Download from Www.Somanuals.com. All Manuals Search And Download.
Send Email
32
Add Recipients from Recent Calls
Receive Calls while Creating Messages
If you receive a call while creating a message a
notification appears. Do one of the following:
1. At the compose message screen, select
Options > Recent Calls when entering a
phone number or email address.
2. Select a number.
•
Select Ignore to ignore the call and return
to the message screen.
•
Press the Send key to answer the call and
your phone automatically saves the
3. Complete your message.
Send to Groups
message to Drafts
.
1. At the compose message screen, select
Options > Message Groups when entering
a phone number or email address.
2. Select a group.
Enter Message Recipients
The following describes how to add recipients
to your messages, depending on the services
provided. Check with your service provider for
availability.
3. Complete your message.
Save Recipients as Contacts
Add Recipients from Contacts
1. At the compose message screen, select
Options > Save Address when entering a
phone number or email address.
1. At the compose message screen, select
Options > Contacts when entering a phone
number or email address.
2. Select a contact from the contacts list.
3. Select a number or address.
2. Select a number or address.
3. Select Options > Save New Contact (to
create a new contact) or Options > Add to
Contact (to add the number or address to
an existing contact).
4. Complete your message.
Add Recipients from Recent List
1. At the compose message screen, select
Options > Recent List when entering a
phone number or email address.
2. Select a number or address.
Add Recipients from Message Text
1. At the compose message screen, select
Options > Add Address when entering the
text to add more recipients.
2. Enter a number or address to add.
3. Complete your message.
3. Complete your message.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
33
Save Messages to Drafts
Attaching Files to Messages
At the compose message screen, select
Options > Save Message when entering the
text. Your phone saves the message to Drafts
for you to complete at a later time.
The following describes how to select Options
to add various files to your messages when
entering the text, depending on the services
provided. Check with your service provider for
availability.
Complete Messages in Drafts
Add Contacts to Messages
•
From Drafts, highlight your desired
message.
1. At the compose message screen, select
Options > Insert Contacts when entering
the text.
•
•
Select Edit or Options > Edit.
Complete your message.
2. Select a contact from your contacts list.
3. Complete your message.
Use Preset Text
Add Preset Text
Add Slides to Messages
1. At the compose message screen, select
Options > Insert QuickText when
entering the text.
2. Select a preset text entry.
3. Complete your message.
Use slides in a multimedia message to send
multiple files of the same type, such as pictures
or voice memos. A multimedia message may
have up to ten slides.
1. At the compose message screen, select
Options > Add New Slide when entering
the text.
Save Messages as Preset Text
1. At the compose message screen, select
Options > Save as QuickText when
entering the text to use it later as preset text.
2. Complete your message.
2. Select a slide and add more files or text if
needed.
To navigate through the slides, select
Options > Next Slide or Previous Slide
To erase the current slide, select Options >
Erase Slide
.
Save Received Messages as Preset Text
When viewing a received message, select
Options > Save as QuickText to use it later as
preset text.
.
3. Complete your message.
You can only attach a limited number of files.
Download from Www.Somanuals.com. All Manuals Search And Download.
Send Messages
34
Add Media Files to Messages
Set Individual Message Settings
The following describes how to set message
settings for individual messages.
Note: Your selection of each of the following
message settings overrides that selected for all
1. At the compose message screen, select
Options > Media Gallery when adding a
media file.
2. Select a file to add to your message.
To remove a media file, select the
applicable option. For example, to remove
a sound, select Options > Remove Sound
3. Complete your message.
messages from Msg Settings
.
Request a Message Receipt
.
1. When entering a message, select Options >
Msg Settings > Msg Receipt > Request to
request a message delivery notice.
Record Sounds for Messages
2. Complete your message.
1. At the compose message screen, select
Options > Record Sound when adding a
sound.
2. Record a sound.
3. Select it to add to your message.
4. Complete your message.
Set Message Priority
1. When entering a message, select Options >
Msg Settings > Set Priority to set the
priority level.
2. Complete your message.
Preview Messages
Change the Callback Number
1. When entering the message, select Options
> Msg Settings > Callback Number
2. Enter your callback number and select OK
3. Complete your message.
1. At the compose message screen, select
Options > Preview Message when
entering the message or media file.
2. Do one of the following:
.
.
–
–
–
If the message has more than one slide,
select Next to view the next slide.
If the message has only one slide, select
Send to send message.
Select Options to access more features.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
35
4. Select Next
.
Send Messages Later
5. Press the OK key to change the date.
1. When entering a message, select Options >
–
–
Scroll left or right to move between the
month, day, and year.
Scroll up or down to change the month,
day, and year.
Msg Settings > Send Later
2. Select Immediate or Set Time to set a
specific time to send the message.
.
3. Press the OK key to change the time.
6. Select Done
7. Complete your message.
.
–
Scroll left or right to move between the
hour, minute, and AM/PM.
–
Scroll up or down to change the hour,
minute, and AM/PM.
Set the Slide Interval
1. When entering the message, select Options
> Msg Settings > Slide Interval
2. Select a time interval for the slides.
3. Complete your message.
4. Select Next
5. Press the OK key to change the date.
.
.
–
–
Scroll left or right to move between the
month, day, and year.
Scroll up or down to change the month,
day, and year.
Set CC and BCC Fields
1. When entering the message, select Options
> Msg Settings > CC & BCC to enable or
disable the CC and BCC address fields.
2. Complete your message.
6. Select Done
7. Complete your message. Your phone will
save the message and send it later.
.
Set the Validity Period
1. When entering a message, select Options >
Request a Message Read Receipt
1. When entering the message, select Options
> Msg Settings > Msg Read Receipt >
Request to request a notice sent upon
reading the message.
Msg Settings > Validity Period
.
2. Select Set Time to set how long to keep
your message valid before removing it
from the phone if not sent.
2. Complete your message.
3. Press the OK key to change the time.
–
Scroll left or right to move between the
hour, minute, and AM/PM.
–
Scroll up or down to change the hour,
minute, and AM/PM.
Download from Www.Somanuals.com. All Manuals Search And Download.
Send Messages
36
Reply to Multimedia Messages (with
Prompt)
Manage Received Messages
Reply to Text Messages
When receiving a message, your phone
displays a notification and the message icon
appears at the top of your screen. The message
icon flashes with an urgent message alert if the
message is urgent.
1. When a message notification appears,
select Inbox (to view the message) or
Ignore (to clear the notification).
An icon appears at the top of your screen
when you have an unread message.
2. From Inbox, highlight a message and select
View > Reply (to compose your message)
or Options (to access more features).
When receiving a message in prompt mode,
your phone displays a notification showing a
new message is available for download.
1. At the download notification, select Yes (to
download the message) or Options (to
retrieve it later or erase it without
downloading).
2. At the message notification, select View (to
view the message) or Later (to check it
later).
3. Select Reply or Options > Reply if the
message has more than one slide.
Select Options to access more features.
4. Complete your message and select Send
Select Options to access more features.
.
3. Complete your message and select Send
.
Reply to Multimedia Messages (with
Auto Retrieve)
Forward Messages
1. When viewing a received message, select
When receiving a message in auto retrieve
Options > Forward
2. Enter a number or address.
3. Complete your message and select Send
.
mode, your phone automatically downloads it
with a notification.
.
Note: If receiving a message during a call, the
phone downloads the message after the call.
1. At a message notification, select View (to
view the message) or Later (to check it
later).
2. After viewing the message, select Reply or
Options > Reply if the message has more
than one slide.
Reply to all Recipients
1. When viewing a received message, select
Options > Reply All to send your reply to
all the message recipients.
2. Complete the message and select Send
.
Select Options to access more features.
3. Complete your message and select Send
.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
37
Reply with a Copy of the Message
Sort Messages in Inbox
1. From Inbox, select Options > Sort
2. Select a sort option.
1. When viewing a received message, select
.
Options > Reply with Copy
.
The original message appears in your reply
message.
Go to Web Addresses in Messages
When viewing a received message, select
Options > Launch Browser to go to a web
address included in the message.
2. Complete your message and select Send
.
Call Sender
When viewing a received message, select
Options > Call to call the sender.
Manage Attached Files
Play Attached Files
Save Received Messages
When viewing a received message with files
attached, select Options > Play (to play an
attached file), Stop (to stop playing), or Mute
(to turn off the sound).
When viewing a received message, select
Options > Save Message to save it to Saved
Msgs
.
View Recipients
When viewing a received message, select
Options > Recipients to check all recipients of
the message.
Save Attached Files
When viewing a received message with files
attached, select the applicable save option to
save the attached files, including graphics,
sounds, contacts (vCard), or events (vCal). For
example, to save a contact, select Options >
View Sender Information
When viewing a received message, select
Options > Sender to view an existing contact,
add to an existing contact, or create a new
contact depending on the sender.
Save Contact
.
Lock Messages
When viewing a received message, select
Options > Lock Msg to protect it from
accidental deletion. To unlock the message,
select Options > Unlock Msg
.
Download from Www.Somanuals.com. All Manuals Search And Download.
Manage Received Messages
38
View Messages with Multiple Slides
Manage Voicemail
Configure your Voicemail
Before your phone can receive voicemail
messages, you need to set up a password and
record a personal greeting with your service
provider.
When you have set up your voicemail, all
unanswered calls to your phone are
automatically transferred to voicemail, even if
your phone is in use or turned off.
1. Press and hold the 1 key.
When viewing a received message containing
multiple slides, use the following options to
navigate through the slides.
•
Next to view the next slide.
Options > Replay to restart the message
from the beginning slide.
•
•
•
•
Options > Pause to pause at the current
slide.
Options > Resume to resume playing the
slides.
Options > Done to exit the message.
View Message Information
2. Follow the system prompts to create a
password and record a greeting.
When viewing a received message, select
Options > Message Info to view the message
priority, sent time, size, etc.
Check your Voicemail
When you receive a voicemail message, a
notification with a voicemail message icon
appears at the top of your screen.
Replay Messages
When viewing a received message, select
Options > Replay to restart the message
(including a slide or sound if contained) from
the beginning.
•
At the voicemail notification, select Call to
call your voicemail number and follow the
system prompts to retrieve the message.
Select Ignore to clear the notification
without checking messages. The
notification icon remains on top of the
screen until you listen to the message.
When only the voicemail message icon
appears on top of the screen, select
Voicemail and follow the system prompts
to retrieve the message.
•
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
39
Unable to Send Messages
Manage Sent Messages
You may not be able to send or receive
messages if your phone’s memory is nearly
full, or if digital service is not available at the
time. To free up memory, erase old messages.
Check Message Status in Sent Folder
Use the following symbols to check the Sent
folder for the status of messages successfully
sent.
Appended Messages
The scheduled message will be sent at
the scheduled time. You cannot cancel
delivery of the message.
If you go over the character limit for a single
message, the phone may automatically append
an empty segment to your message to make
space.
The message was sent. You cannot
cancel delivery of the message.
Warning: Your service provider may charge
you for each message segment.
The message has been received.
The message has been sent to more than
one recipient.
When you start a message, the maximum
character limit appears once you are in the
message entry field. This number counts down
as you enter characters, until it reaches 0.
If you continue to enter text after this counter
reaches 0, a message segment may be
appended. When you reach the message size
limit, you are prompted to edit the message or
alerted that the message is being appended.
Note: Appended messages may not be
available on all phones. Check with your
service provider.
Check Message Status in Outbox
Use the following symbols to check your
Outbox for the status of messages sent but still
in process.
The message is pending and will be sent
when possible. You can cancel delivery
of the message.
The message cannot be sent because
service is not available. An alert appears
on your phone if the message cannot be
sent.
Manage Web Alerts
1. From Web Alerts, select an alert.
2. Select Connect to launch the browser.
Download from Www.Somanuals.com. All Manuals Search And Download.
Manage Sent Messages
40
Set Message List View
Message Settings
From Msg List View, select one of the
following to set your message list display:
The following message settings affect all
messages unless you change them for
individual messages.
•
•
•
•
Sender & Preview displays the sender and
first part of messages.
Sender & Date-Time displays the sender
and sent time of messages.
Msg Preview displays the first part of
messages.
Sender displays the message sender.
Set Message Alerts
1. From Alerts, select Msg Alert
2. Select an alert for messages.
If you select an & Remind alert, the phone
notifies you once when receiving a new
message and notifies you again every five
minutes. To stop a reminder alert, select
.
Set your Signature
You can create a signature to appear at the end
of all outgoing messages.
Ignore
.
1. From Signature, enter your signature.
2. Select OK to save the signature.
Note: The signature counts towards the
character limit of your message.
Set Page Alerts
1. From Alerts, select Page Alert
.
2. Select an alert for pages.
If you select an & Remind alert, the phone
notifies you once when receiving a new
message and notifies you again every five
minutes. To stop a reminder alert, select
Edit Preset Messages
Your phone comes with preset messages, such
as “Please call me,” which you can insert into
the body of a text message. You can edit or
create up to 40 preset messages.
Ignore
.
Set Voicemail Alerts
1. From Alerts, select Voicemail Alert
2. Select an alert for voicemails.
If you select an & Remind alert, the phone
notifies you once when receiving a new
message and notifies you again every five
minutes. To stop a reminder alert, select
1. From QuickText, do one of the following:
.
–
Scroll to a preset message and select
Edit
.
–
Select New Msg to create a new preset
message.
2. Enter or edit the text.
3. Select Save
.
Note: You can also save messages you have
written or received as preset messages.
Ignore
.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
41
Enable Auto Retrieve
From Auto Retrieve, select one of the
following:
Enable Auto-Erase
Use Auto-Erase to set your phone to erase
messages automatically when it needs memory
for incoming messages.
•
Disabled turns off auto retrieve and
prompts you before downloading any
multimedia messages.
From Auto-Erase, select one of the following:
•
•
Disabled erases no messages.
Old Inbox Msgs erases old messages in
Inbox when memory is needed.
•
Enabled turns on auto retrieve to
automatically download multimedia
messages.
•
•
Sent Msgs erases old messages in Sent
Msgs when memory is needed.
Both erases old messages in both Inbox
and Sent Msgs when memory is needed.
Enable CC/BCC Fields
From CC and BCC, select Disabled (to hide
the CC and BCC fields) or Enabled (to show
them).
Set Default Text
You can change the default text entry mode
when creating a text message. This setting
applies only to the Message field, not the Send
To field.
From Default Text, select Normal Alpha (to
enter text letter by letter) or Rapid Mode (to
enter text with word recognition).
Set Callback Number
1. From Callback Number, enter a new
number to change your default callback
number.
2. Select OK to save the number.
Enable Save to Sent
From Save to Sent, select Enabled to
automatically save outgoing messages to the
Sent Msgs folder.
Request Text Message Receipts
From Text Msg Receipt, select Request to
request a notification when a recipient has
received your text message.
Request Multimedia Message Receipts
From Pic Msg Receipt, select Request to
request a notification when a recipient has
received your multimedia message.
Download from Www.Somanuals.com. All Manuals Search And Download.
Message Settings
42
Set your Voicemail Number
Often your service provider automatically
programs your voicemail number (the number
your phone calls to retrieve voicemail). To
change it:
Message Groups
You can create groups for messaging.
View Message Groups List
1. From Message Groups, view your
preloaded groups, followed by the custom
groups you have created.
1. From Voicemail Number, select Edit
.
2. Enter your voicemail number. (Use
2. Highlight a group and do one of the
following:
Options > Time Pause or Hard Pause to
enter pauses.)
–
Press the OK key to view the groups
details.
3. Select Save
.
Erase Recent List
–
–
Select New to create a new group.
Select Options to access more
functions.
From Erase Recent List, select Yes to clear
the list of recipients you have recently sent
messages to.
Create a New Message Group
1. From Message Groups, select New
2. Enter a name for the group and select Next
3. Select contacts from the list provided. A
check mark appears next to each selection.
You can also remove checkmarks.
4. When finished, select Done
Your new group appears the next time you
view your groups list.
Request Text Message Read Receipts
From Text Msg Read Receipt, select Request
to request a notification when a recipient has
read your text message.
.
.
Set Multimedia Message Response
From Pic Msg Reply by, select Text Msg or
Pic Msg to set the default reply to a
multimedia message.
.
If you select Text Msg, you go to the text
message compose screen when you reply to a
multimedia message. When you select Pic
Msg, you go to the multimedia message
compose screen.
Send Text Messages to Message
Groups
1. From Message Groups, highlight a group.
2. Select Options > Send Text Msg
3. Complete your text message and select
Send
.
.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
43
Send Multimedia Messages to
Message Groups
1. From Message Groups, highlight a group.
Erase a Message Group
1. From Message Groups, highlight a group.
2. Select Options > Erase > Yes.
2. Select Options > Send Pic Msg
3. Complete your multimedia message and
select Send
.
Erase Messages
.
Erasing old messages frees up memory in your
phone. You can erase messages as you send or
read them, erase them one at a time, or erase
them all at once.
Add Contacts to Message Groups
1. From Message Groups, highlight a group.
2. Select Options > Edit
.
Erase a Single Message
When viewing a received message, select
3. If you are modifying a group you created,
select Next. Otherwise, go to the next step.
4. Select contacts from the list provided. A
checkmark appears next to each contact in
the group. Press the OK key to add or
remove checkmarks.
Options > Erase > Yes
.
Note: You can erase a scheduled message, but
cannot cancel its delivery.
Erase Messages from a Folder
From Erase Msgs, select a folder to erase
messages from. For example, to erase received
messages, select Inbox > Yes
Note: You cannot recover deleted information.
5. When finished, select Done
.
Assign Message Tone to Message
Group
1. From Message Groups, select a group.
2. At the groups details screen, scroll to the
group name.
3. Select Options > Msg Tone > Assign Msg
Tone and a ringer from the list. Scroll to
play the ringers.
.
Erase All Messages
From Erase Msgs, select All > Yes to erase all
messages from all folders, except for voicemail
messages.
Note: You cannot recover deleted information.
Send a Message Group vCard
Check Message Count
1. From Message Groups, highlight a group.
From Message Count screen, check how
2. Select Options > Send > Via Bluetooth
3. Complete the appropriate task to send the
contact information.
.
many messages you have stored.
Download from Www.Somanuals.com. All Manuals Search And Download.
Erase Messages
44
7
@metro
How does BREW Work?
Download an Application
Your Kyocera phone has the added ability to
download and manage applications through
BREW.
1. From @metro, select MobileShop >
Catalog. When a connection is made, a list
of application types appears.
BREW brings you the full range of
applications and services you have come to
expect from the Internet: Email and instant
messaging, real-time navigation services,
group chat, games, relevant news, and much
more.
You connect to the server, download
applications, and then manage them as you
like. When you choose an application, you
have the option of choosing a demo, various
limited use options, or the full version—all
varying in price. If you choose a demo, BREW
lets you know when it has expired. If you
choose a priced version, the amount is added to
your phone bill. BREW also lets you know if
you are running out of memory. At that point,
you can either disable an application or remove
it completely.
2. Select an application type. A list of
applications appears. Long titles scroll left
as you highlight them.
3. Select an application. A list of usages
appears. There may be one or more usages
available. Prices are specified for each
usage.
4. Select a usage for the application. You are
prompted to confirm your purchase.
5. Select Yes to confirm. The application
downloads to your phone. Download times
may vary.
To open the application now, select Yes. If you
select No, you return to @metro, where you
see a link to your new application.
Note: Your connection to the application
server automatically ends after 30 seconds,
unless you connect again to download more
apps. If you want to end the connection
manually, press the End key on your phone.
Once applications are loaded, you can update
to newer versions as they become available.
For more information about BREW
capabilities and application pricing, contact
your service provider.
Access Help for @metro
From @metro, select Help to get instructions
on how to run and manage your downloaded
applications.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
45
8
MetroWEB
You can use your phone to browse the Internet
if you have obtained phone Internet services
from your service provider and if over-the-air
Internet access is available in your area.
Browse the Web
A browser home page with a list of bookmarks
and some browser menu options appear when
you are connected to the Web. The lock icon
appears in a secure session. You can do the
following:
Launch Browser
Select MetroWEB to launch the browser. An
alert appears notifying of airtime fees, if you
have enabled web alerts. Select OK to
continue.
•
To choose a site, scroll to the link and press
the OK key.
•
An underline and an arrow indicate that
there is more text. Scroll down to view the
rest of the text.
If this is the first time you have connected to
the Internet, a message informs you that
security is not yet enabled for your browser.
Select Yes to enable security.
•
Press the Back key to return to the previous
screen.
•
•
Press the End key to exit.
Select Options to access more browser
features.
Add a Bookmark
1. Surf to the Web page you want to
bookmark and select Options > Add to
Bookmarks
.
2. Edit the bookmark’s details, if needed.
3. Select Options > Save to save the
bookmark.
To access your saved bookmarks, select
Options > Bookmarks from any web page.
Download from Www.Somanuals.com. All Manuals Search And Download.
Launch Browser
46
9
Settings
Settings Menu
Select Settings from the main menu to access the following functions:
Level 1 >
Settings
Level 2 >
Level 3
Bluetooth
Convenience
Access these options: On/Off
,
My Devices, and Settings
.
Access these options: Date/Time Display
,
Set Time/Date
(with Airplane Mode enabled), Airplane Mode Auto
Keyguard Auto-Hyphen 1-Touch Dialing Fast Find
Frequent List Minute Alert Missed Call Alert, and Any
Key Answer
,
,
,
,
,
,
,
.
Display
Access these options: Set Wallpaper
View Icon Display Mode My Banner
Brightness Contrast Language, and Time/Date Format.
,
Themes
,
Main Menu
,
,
,
Backlighting
,
,
,
Sounds
Access these options: Ringers
,
Roam Ringer Activation
,
Volume Pwr On/Off, and Key Sounds
,
.
Accessories
Network
Access these options: Headset Sounds
,
Auto-Answer TTY
,
Device, and T-coil Hearing Aid
.
Access these options: Privacy Alert
Roam/Svc Alert Roam Option Set Phone Line
and Roam Call Alert
,
Voice Privacy
,
,
,
,
Location,
.
Security
Access these options: Lock Phone
Lock Code
,
Limit Calls, and New
.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
47
2. From My Devices, select Find New. Your
phone then searches and detects any
available Bluetooth devices in the vicinity.
You must enable the Bluetooth feature on
your phone.
Bluetooth
The Bluetooth® wireless technology (not
available on all phones) enables wireless
connectivity with accessories such as portable
or installed hands-free car kits, headsets,
handsets, computers, and so on. For details,
check with your service provider.
3. At the device list, highlight a device and
select Add
.
Accept the pairing if prompted.
You must use a Bluetooth device (compatible
with Class 2 Bluetooth wireless technology,
version 1.2) in order to use this phone
wirelessly. Bluetooth accessories display a
symbol on your phone.
4. If necessary, enter the password provided
with the Bluetooth device and select OK
.
With the password accepted, the device
appears in your device list.
Enable Bluetooth
Use Bluetooth Devices
Before you can connect your phone with a
Bluetooth device, you need to enable the
Bluetooth feature on your phone.
From On/Off, select On Visible or On
Connect to a Device
Before you can use Bluetooth, you must get
your phone ready to communicate with a
device. This is called “connecting.”
To connect your phone to a Bluetooth device,
from My Devices, highlight a device and select
Invisible
.
Pair with a Device
Connect
.
To enable your phone to communicate with a
Bluetooth device, you need to "pair" the device
with your phone. The following instructions
describe the process. You may also need to
reference the user guide provided with your
Bluetooth device.
A notification appears confirming the
connection. You can now use the device with
your phone.
Disconnect from a Device
From My Devices, highlight a connected
device and select Disconnect
1. Prepare the Bluetooth device (accessory)
for pairing as described in the device’s user
guide.
.
Download from Www.Somanuals.com. All Manuals Search And Download.
Bluetooth
48
Rename a Device
Limit Visibility
1. From My Devices, highlight a device.
By default your phone is always visible, if set
to visible mode. You can limit the time your
phone is visible to other Bluetooth devices.
From Visible Duration, select an option to set
the phone visible for your selected time before
becoming invisible.
2. Select Options > Rename
.
3. Enter a new name and select Save
.
Delete a Device
You can delete a Bluetooth device that you
have paired your phone with.
View Supported Services
Select Services to view a list of the Bluetooth
service profiles your phone supports.
1. From My Devices, highlight a device.
2. Select Options > Delete > Yes
.
View Device Services
Enable OBEX Authentication
A Bluetooth device paired with your phone
may have more than one service profile (such
as Headset, Handsfree, and so on). Do the
following to check the services available:
1. From My Devices, highlight a device.
From OBEX Authentication, select Enabled
With object exchange (OBEX) authentication
enabled, you need a user name and password to
transfer files via Bluetooth.
.
2. Select Options > Services
3. At the service list, highlight a profile and
.
Convenience
Use these settings to make your phone more
convenient to use.
select Connect to change the active profile.
Change Bluetooth Settings
From Settings, you can modify the following
Bluetooth features.
Enable Date/Time Display
From Date/Time Display, select Enabled to
show the date and time when the phone is in
idle state.
Change Phone’s Name
You can change the name presented for other
Bluetooth devices’ search of your phone.
From My Name, enter a new name and select
Save
.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
49
make emergency calls to designated
emergency numbers. Please check with
uniformed personnel before operating your
phone in Airplane mode.
From Airplane Mode, select Enabled > OK
to activate airplane mode.
Set Date and Time
In Airplane mode, you can set the time and
date manually.
Note: You can only access Set Time/Date with
Airplane Mode enabled.
1. From Set Time/Date, do the following to
change the date:
With airplane mode enabled, you can also set
the time and date manually.
–
Scroll left or right to move between the
month, day, and year fields.
Scroll up or down to change the month,
day, and year.
Auto Keyguard
–
Enable Auto Keyguard
2. Press the OK key to save the date.
3. Do the following to change the time:
Use Auto Keyguard to automatically lock the
keypad after 30 seconds of inactivity to prevent
accidental key presses.
From Auto Keyguard, select Enabled or from
the home screen, press and hold the * Shift
key.
–
Scroll left or right to move between the
hour, minute, and AM/PM fields.
Scroll up or down to change the hour,
minute, and AM/PM.
–
4. Press the OK key to save the time.
5. Select Done
Unlock Keyguard
From the home screen, select Unlock and press
.
the * Shift key to unlock the keypad.
Enable Airplane Mode
While in an airplane, it is normally required
that you turn off your mobile phone because it
emits RF signals that interfere with air traffic
control. In airplane mode, however, your
phone does not emit RF signals. You cannot
make or receive calls, send text messages, use
the Browser or Bluetooth, but you can play
games, use the Scheduler, set the clock, and
Enable Auto-Hyphenation
Auto-hyphenation, when enabled,
automatically inserts hyphens into your phone
numbers to be consistent with the U.S. dialing
plan (or the North American Numbering Plan).
From Auto-Hyphen, select Enabled to turn on
auto-hyphenation.
Download from Www.Somanuals.com. All Manuals Search And Download.
Convenience
50
Use 1-Touch Dialing
Enable Minute Alert
The 1-Touch Dialing feature is the fastest way
to call a speed dial location. To call a contact
with speed dial, press and hold the speed
dialing location.
From Minute Alert, select Enabled. Your
phone alerts you with a short beep ten seconds
before each minute passes during a call.
Set Missed Call Alert
From Missed Call Alert, select an alert type
for missed calls.
If you select an & Remind alert, the phone
notifies you once when receiving a new
message and notifies you again every five
minutes. To stop a reminder alert, select
If it is a two-digit location, press the first digit
briefly, then press and hold the second digit.
Note: To use 1-Touch dialing, you must enable
1-Touch dialing on your phone and have a
speed dial location assigned to a contact.
From 1-Touch Dialing, select Enabled to turn
on 1-touch dialing.
Ignore
.
Call Contact using Fast Find
1. From Fast Find, select Enabled to turn on
fast find.
2. From the home screen, press the keys
corresponding to the letters of the name
you want to find. A matching contact or
speed dial entry appears.
Enable Any Key Answer
From Any Key Answer, select Enabled to
answer calls when you press any key on the
keypad.
Display
3. Scroll to your desired contact and press the
Send key to call the number.
Set Wallpaper
You can select a wallpaper for your phone’s
home screen.
Enable Frequent List
1. From Set Wallpaper, select Saved Images
or Wallpapers
2. Select a file.
From Frequent List, select Enabled. With
Frequent List enabled, the last 15 of your
most frequently called contacts appear at the
beginning of your contacts list. Scroll past the
double line to view the entire contacts list.
.
To turn off wallpaper, select None
.
Set Theme
From Themes, select a color theme for the
display background.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
51
Set Main Menu View
From Main Menu View, select one of the
following:
Set Greeting Banner
The banner is the personal label for your
phone, appearing on the home screen above the
time and date.
•
Grid displays icons of each menu item,
with its name at the top of the screen.
List displays a list of all menu items.
1. From My Banner, select Edit
2. Press the Back key to clear the current
banner.
3. Enter your new text (up to 14 characters) or
press the # Space key for a blank banner.
.
•
The next time you view the Menu, your
selected menu style appears.
Set Icon Display Mode
To change the application bar display, select
Icon Display Mode and one of the following:
4. Select Save
.
Set Backlight Duration
•
•
•
Always Visible displays the application bar
solid all the time.
Use Backlighting to minimize the bright time
and maximize the battery life.
From Backlighting, select one of the
following:
Translucent all the time displays the
application bar translucent all the time.
Invisible but appears on key press does
not display the application bar unless you
press the Navigation key.
•
Always Dim forces the backlight to remain
dim before turning off.
•
7 Seconds 10 Seconds, 15 Seconds, or 30
,
•
Translucent but appears solid on key
press displays the application bar
translucent until you press the Navigation
key.
Seconds turns backlighting on for the set
time after your last keypress.
•
Always Bright forces the backlight to
remain bright before turning off.
•
Off turns off the application bar.
When the application bar is turned off, the
home screen shortcuts will change. Scrolling
left launches MetroWEB and scrolling right
Set Brightness
1. From Brightness, scroll to change the
brightness level.
launches @metro
.
2. Select Save
.
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
52
Set Contrast
1. From Contrast, scroll to change the
contrast level.
Volume
From Volume, you can modify the following
settings.
2. Select Save
.
Set Ringer Volume
1. From Ringer Volume, scroll right or left to
set the ringer volume.
Set Language
From Language, select a language.
2. Press the OK key to save.
Set Time and Date Format
From Time/Date Format, select a time and
date format.
Set Speakerphone Volume
1. From Spkrphone Volume, scroll right or
left to set the speakerphone volume.
2. Press the OK key to save.
Sounds
Your phone has several settings that control the
sound. You can select from a variety of ringers
and adjust the volume.
Set Earpiece Volume
1. From Earpiece Volume, scroll right or left
to set the earpiece volume.
2. Press the OK key to save.
Ringers
From Ringers, you can modify the following
Set Keypad Volume
1. From Key Volume, scroll right or left to set
the keypad volume.
settings.
Set Ringers
From Ringer Type, select a ringer. (Scroll
2. Press the OK key to save.
down the list to play the ringers.)
Enable Smart Volume
Set Roam Ringer
From Roam Ringer, select a ringer. (Scroll
down the list to play the ringers.)
From Smart Volume, select Enabled to
automatically adjust the volume during a call,
based on surrounding noise levels.
Enable Roam Ringer
From Roam Ringer Activation, select
Enabled to activate the roam ringer.
Set Power On/Off Sounds
From Pwr On/Off, select Enabled to have
your phone play the sound when turned on.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
53
3. Select one of the following:
Set Key Press Sounds
–
–
–
TTY Off disables TTY.
From Key Sounds, select Tone Click, or Off
,
TTY On enables TTY devices.
TTY On + Talk enables TTY devices
and voice carry over.
to set the sounds you hear when pressing the
keypad.
–
TTY On + Hear enables TTY devices
and hearing carry over.
Accessories
Note: You can also enter ##889 with your
keypad and select TTY to enable TTY.
Set Headset Sounds
With a headset attached to your phone, you can
play the ringer through the headset or phone
speaker.
Connect to Hearing Aid Device
With a T-coil hearing aid device (sold
separately) connected, you can enable the
hearing aid feature.
1. Connect the T-coil hearing aid device to
your phone.
From Headset Sounds, select Out of phone
(ringing from the phone speaker) or Out of
headset (ringing from the headset).
Enable Auto-Answer
From Auto-Answer, select After 5 seconds
The phone automatically answers after five
seconds with a headset attached.
.
2. From T-coil Hearing Aid, select OK >
Enabled
.
Network
Enable Privacy Alert
From Privacy Alert, select Enabled to set
your phone to alert you when enhanced digital
CDMA privacy is lost or regained.
Connect to TTY Device
You can connect the phone to a teletype (TTY)
device for the hearing impaired. (TTY device
sold separately.)
Note: Enable TTY only when using the phone
with a TTY device.
1. Connect the TTY device to your phone.
2. From TTY Device, select OK to clear the
notification.
Enable Voice Privacy
From Voice Privacy, select Enhanced to use
enhanced digital CDMA privacy.
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
54
Note: You must first establish a second phone
line with your service provider. Once
established, a second phone number becomes
available in the menu for selection.
Enable Roaming Service Alert
Use this setting if you want the phone to alert
you when you roam outside of your home
service area.
From Set Phone Line, read the note and select
OK and one of the phone lines.
From Roam/Svc Alert, select one of the
following:
When using one line, you cannot receive calls
from the other. It would be as if the phone were
“off” for that number. Your voicemail,
however, still takes messages. All contacts and
settings are shared for both lines.
•
•
Disabled turns roaming service alert off.
When no svc alerts you with three tones
decreasing in pitch when service is lost and
three tones increasing in pitch when service
is acquired again.
•
•
On roam change alerts you with two
decreasing tones when roaming service is
acquired and three increasing tones when
home area service is acquired again.
On any change alerts you with three
increasing tones if there is a change in
roaming service or three decreasing tones if
the phone loses service.
Set Location Information
Use Location to share your location
information with network services other than
emergency services (for example, 911, 111,
999 and 000) in serviced areas. This feature
works only when your phone is in digital
mode. You do have the option of turning off
the locator to emergency services.
Set Roaming Restrictions
You can restrict your phone from making a call
when roaming.
From Roam Option, select Automatic (to
allow roaming) or MetroPCS Only (to
disallow roaming).
From Location, select one of the following:
•
911 Only (default) shares your position
information only with emergency services
when you call your 3-digit emergency
code.
•
Location On shares your position
information, in addition to emergency
services.
Set Phone Line
Your phone can have two service accounts, or
phone lines, associated with it. Each phone line
has its own phone number.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
55
–
–
On power up locks the phone every
time you turn it on.
Now locks the phone immediately.
Enable Roaming Call Alert
You can set the phone to warn you before you
answer or place a call while roaming.
Note: Call prompt is disabled when the phone
is in Emergency Mode.
Unlock the Phone
1. From the home screen, select Unlock
2. Enter your four-digit lock code.
.
From Roam Call Alert, select Enabled
.
The phone emits a distinctive ring to indicate
when you are roaming during a call. To accept
or place a call while roaming, you must
Set Limit Calls
You can limit the calls that can be made from
your phone to emergency numbers, your
contacts, and your service provider’s numbers.
1. From Security, enter your four-digit lock
code.
press
1.
Security
This section describes the security features on
your phone. You can adjust these features to
prevent access to your personal information.
All security features are shielded by a
2. Select Limit Calls and one of the
following:
–
–
No Limit does not limit calls.
Limit Outgoing limits outgoing calls
while incoming calls still work.
Limit All limits both incoming and
outgoing calls.
four-digit lock code (typically 0000 or the last
4 digits of your phone number).
–
Lock Phone
Set Lock Phone
Change Lock Code
With your phone locked, you can call only
emergency numbers or your service provider’s
customer service number. You can still receive
incoming calls.
1. From Security, enter your four-digit lock
code.
Change your lock code from the default.
1. From Security, enter your four-digit lock
code.
2. Select New Lock Code > Yes
3. Enter a new four-digit code.
4. Re-enter your new lock code.
.
2. Select Lock Phone > OK and one of the
following:
–
Never leaves the phone always
unlocked.
Download from Www.Somanuals.com. All Manuals Search And Download.
Security
56
10 Media Gallery
Use Media Gallery to retrieve and playback media files and other downloads.
Media Gallery Menu
Select Media Gallery from the main menu to access the following functions:
Level 1 >
Level 2 >
Images
Level 3
Media Gallery
Access these options: Saved Images
Caller IDs
,
Wallpapers, and
.
Tones
Access these options: Saved Sounds
,
Ringers, and Voice
Memos
.
Delete All
Access these options: Images Only
,
Sounds Only, and
Delete All
.
Assign a Caller ID
Images
Send an Image
1. From Caller IDs, select an image.
2. Select Assign
.
1. From Saved Images, select an image.
2. Select Send > Via MMS (to attach to a
multimedia message) or Via Bluetooth (to
send to a Bluetooth-enabled device).
3. Complete the appropriate task.
3. At the contacts list, select a contact.
Tones
Send a Sound
1. From Saved Sounds, highlight a sound.
2. Select Send > Via MMS (to attach to a
multimedia message) or Via Bluetooth (to
send to a Bluetooth-enabled device).
3. Complete the appropriate task.
Change the Default Wallpaper
1. From Wallpapers, select a wallpaper.
2. Select Set Default
.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
57
Assign a Ringer
Assign a File
1. From Ringers, highlight a ringer.
2. Select Assign and choose how you want to
assign the ringer.
1. From a media file list, highlight a file.
2. Select Options > Assign and choose how
to assign the file.
3. Complete the appropriate task.
3. Complete the appropriate task.
Play a Voice Memo
Lock a File
1. From Voice Memos, highlight a memo you
have recorded.
1. From a media file list, highlight a file.
2. Select Options > Lock to protect a file
from being accidently erased. To unlock the
2. Select Play
.
file, select Options > Unlock
.
Use the Navigation key to control the
playback tools displayed.
Play a File
1. From a media file list, highlight a file.
2. Select Options > Play
Media File Options
.
Use the Navigation key to control the
playback tools displayed.
Rename a File
1. From a media file list, highlight a file.
2. Select Options > Rename
3. Enter a new name and select Save
You can only rename unlocked files. Preloaded
files on your phone are always locked.
.
View File Details
.
1. From a media file list, highlight a file.
2. Select Options > Details to view the
details such as file size or save date.
3. Select OK to exit.
Send a File
1. From a media file list, highlight a file.
2. Select Options > Send > Via MMS (to
attach to a multimedia message) or Via
Bluetooth (to send to a Bluetooth-enabled
device).
Modify a File
1. From a media file list, select a file.
2. Select Options > Modify
3. Select Options and an option to rotate,
resize, and so on.
4. When done, select Save to save over an
existing file or as a new one.
.
3. Complete the appropriate task.
Download from Www.Somanuals.com. All Manuals Search And Download.
Media File Options
58
Erase All Media Files
Erase Media Files
Erase a Single File
1. From a media file list, highlight a file.
2. Select Options > Erase > Yes
You can only erase unlocked files. Preloaded
files on your phone are always locked.
From Delete All, select Delete All > Yes to
erase all files in the Media Gallery folder.
Note: You can only erase unlocked files.
Preloaded files on your phone are always
locked.
.
Erase All Files in a Folder
From a media file list, select Options > Erase
All > Yes
.
Note: You can only erase unlocked files.
Preloaded files on your phone are always
locked.
Erase All Image Files
From Delete All, select Images Only > Yes to
erase all files in the Images folder.
Note: You can only erase unlocked files.
Preloaded files on your phone are always
locked.
Erase All Sound Files
From Delete All, select Sounds Only > Yes to
erase all files in the Tones folder.
Note: You can only erase unlocked files.
Preloaded files on your phone are always
locked.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
59
12 Tools
Tools Menu
Select Tools from the main menu to access the following functions:
Level 1 >
Tools
Level 2 >
Level 3
Voice Memo
Scheduler
Access these options: Record New and Recorded Memos.
Access these options: Add New Event
,
View Month, View
Day Go to Date View All Events, and Settings.
,
,
Alarm Clock
Tip Calculator
Calculator
Timer
Set an alarm.
Calculate a tip.
Perform basic calculations.
Set a countdown timer.
Use a stopwatch timer.
Stopwatch
Play Voice Memos
Voice Memo
1. From Recorded Memos, highlight a
Use Voice Memo to record and play back
memo.
audio memos.
2. Select Play to play the memo or Options to
Record Voice Memos
access more features.
1. From Voice Memo, select Record New
2. Record your voice memo and select Stop
when done.
.
3. Select Save
.
If you receive an incoming call while recording
a memo, the memo is saved and the incoming
call screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
61
–
Scroll up or down to change hour and
minute.
Scheduler
Use Scheduler to schedule events and set
Press the OK key to save and move to the
next field.
reminder alerts.
Create an Event
1. From Add New Event, enter a name.
Scroll down to move to the next field when
done.
6. Press the OK key to select a priority from
the list.
7. Press the OK key to select a reminder from
the list.
2. Press the OK key to select an event type
from the list.
8. Press the OK key to select a reminder
sound from the list.
3. Press the OK key to change the date, if
needed.
9. Press the OK key to select During Event
to enable silent mode or Off to have normal
sounds.
10. Press the OK key to select a recurring
event from the list, if needed.
–
Scroll left or right to move between
month, day, and year fields.
Scroll up or down to change month,
day, and year.
–
11. Select Save
.
Press the OK key to save and move to the
View Events
next field.
4. Press the OK key to change the time, if
View Events by Month
needed.
1. From View Month, scroll through the
month view. (Days with events are
highlighted.)
2. Press the OK key to select a date.
3. Do one of the following:
–
–
Scroll left or right to move between
hour, minute, and AM/PM fields.
Scroll up or down to change hour,
minute, and AM/PM.
Press the OK key to save and move to the
next field.
–
Scroll left or right to move to another
date.
5. Press the OK key to change the duration, if
–
–
Select an event.
Scroll to a time and select Add New to
create a new event.
needed.
–
Scroll left or right to move between
hour and minute fields.
–
Select Options to access more features.
Download from Www.Somanuals.com. All Manuals Search And Download.
Scheduler
62
View Events by Date
Sort Events by Priority
From View Day, do one of the following:
From View All Events, select Options > Sort
by Priority to sort events by their assigned
priority.
•
•
•
Scroll left or right to move to another date.
Select an event.
Scroll to a time and select Add New to
create a new event.
Modify Events
•
Select Options to access more features.
Edit an Event
1. From View Day, select an event.
2. At the event details screen, select Options
Go to a Specific Date
1. From Go to Date, scroll left or right to
move between month, day, and year fields.
Scroll up or down to change month, day, or
year.
> Edit
.
3. Modify the event and select Save
.
Send an Event
1. From View Day, select an event.
2. Press the OK key to select the date.
View Events by List
From View All Events, select an event from
the list or Options to access more features.
2. At the event details screen, select Options
> Send > Via MMS (to attach the file to a
multimedia message) or Via Bluetooth (to
send the file to a Bluetooth-enabled
device).
Return to the Current Date
From View Day, select Options > Go to
Today to return to the current date.
3. Complete the appropriate task.
Copy an Event
1. From View Day, select an event.
2. At the event details screen, select Options
Sort Events by Time
From View All Events, select Options > Sort
by Time to sort events by time.
> Copy
.
3. Enter a new name for the event.
4. Complete the event and select Save
Sort Events by Type
From View All Events, select Options > Sort
.
by Type to sort events by their assigned type.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
63
Set Scheduler Hours
1. From Scheduler Hours, modify the start
Erase Events
Erase an Event
1. From View Day, select an event.
2. At the event details screen, select Options
and end times.
–
–
Scroll left or right to move between
hour, minute, and AM/PM fields.
Scroll up or down to change hour,
minute, and AM/PM.
> Erase > Yes
.
Erase the Current Day’s Events
2. Select Save when done.
From View Day, select Options > Erase
Today’s Events > Yes to erase all events on
that day.
Erase Events Automatically
From Auto Erase, select an option from the
list to set when to automatically erase your past
events.
Erase All Events
From View All Events, select Options >
Erase All Events > Yes to erase all events
from the phone.
Set Event Priority
From Priority, select an option to set every
event you create with this priority type.
Note: You cannot recover deleted information.
Erase All Past Events
Set Event Reminder
From Reminder, select an option to set every
event you create with this reminder setting.
From View All Events, select Options >
Erase All Past Events > Yes to erase all past
events from the phone.
Set Event Reminder Alert
Note: You cannot recover deleted information.
From Reminder Sound, select an option to set
every event you create with this reminder alert.
(Scroll to listen to sounds.)
Change Scheduler Settings
From Settings, you can modify the following
features.
Set Event Silent Mode
From Silent Mode, select an option to set
every event you create with this silent mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
Scheduler
64
Set the Quick Alarm
Alarm Clock
1. From Alarm Clock, scroll to the quick
You can set up to four alerts with your phone’s
three alarm clocks and one quick alarm.
alarm and select Set
.
2. Choose a time. (A notification shows the
quick alarm is on.)
When the quick alarm rings, select Off to turn
off the alarm, or Reset to set the quick alarm
again.
Note: The alert occurs only if the phone is on.
Set an Alarm
1. From Alarm Clock, scroll to one of the
alarms and select Set
.
2. Press the OK key to change the time, if
needed.
Use Tip Calculator
–
–
Scroll left or right to move between
hour, minute and AM/PM fields.
Scroll up or down to change hour,
minute and AM/PM.
1. From Tip Calculator, enter the amount of
your bill.
2. Scroll down to select the percentage you
want to tip.
Press the OK key to save time and move to
the next field.
The total bill with tip is displayed. If you
are finished, select Done. Otherwise, go on
to the next step.
3. Press the OK key to select a sound from the
list.
4. Press the OK key to select a recurring
alarm from the list, if needed.
5. Press the OK key to enter a note.
3. Scroll down to enter the number of people
sharing the bill (or enter 1 if paying the
entire bill).
4. Select Next to view the final bill.
5. Select Done when finished.
6. Select Save
.
When the alarm rings, select Stop to turn off
the alarm or Snooze to set the alarm to ring in
another ten minutes.
Use Calculator
1. From Calculator, enter the first number.
2. Select a mathematical operation:
–
–
–
–
Scroll left to multiply.
Scroll right to divide.
Scroll up to add.
Scroll down to subtract.
Your selection will appear highlighted.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
65
3. Enter the second number, and press the OK
key to view the result.
4. Select Exit to return to the menu, or
Options and one of the following:
Use Stopwatch
From Stopwatch, select from the following
options:
•
•
•
Start begins counting.
Stop pauses counting.
Reset clears the stopwatch.
–
MS replaces the value currently stored
in memory with the displayed result on
the screen.
Press the Back key to exit.
–
–
–
M+ adds displayed result on the screen
to the value currently stored in memory.
MR displays value currently stored in
memory on the screen.
MC clears value currently stored in
memory.
Use Timer
The timer counts down for the specified time.
It beeps when that amount of time has elapsed.
1. From Timer, select Set
.
2. Enter the time length.
–
Scroll left or right to move between
hours, minutes, or seconds fields.
Scroll up or down to change hours,
minutes, or seconds.
–
3. Select Sound, and choose from the list to
modify the sound.
4. To work the timer, select from the
following options:
–
–
–
Start begins the countdown.
Stop pauses the countdown.
Reset clears the timer.
When the countdown is complete, select Off to
silence the alarm.
Download from Www.Somanuals.com. All Manuals Search And Download.
Use Timer
66
13 Get Help
Note: From Phone Info, select Build Info
.
Customer Support
Scroll down to MEID. The 18-digit number is
the MEID number. If your phone uses an
electronic service number (ESN), ESN
Your service provider’s customer support
department may be accessible directly from
your phone when you dial a number, such as
*611 (check with your service provider). They
can answer questions about your phone, phone
bill, call coverage area, and specific features
available to you, such as call forwarding or
voicemail. For questions about the phone
features, refer to the materials provided with
your phone, or visit
replaces MEID
.
Qualified Service
If the problem with your phone persists, return
the phone with all accessories and packaging to
the dealer for qualified service.
.
Phone Accessories
For additional questions, you may contact the
Kyocera Communications Inc. Customer Care
Center in any of the following ways:
To shop for phone accessories, visit
also call us at 800-349-4188 (U.S.A. only)
or 858-882-1410.
•
•
•
Email: [email protected].
Phone:
Become a Product Evaluator
–
U.S. and Canada: 1-800-349-4478 or
1-858-882-1401
To participate in the testing and evaluation
of Kyocera Communications Inc. products,
including cellular or PCS phones, visit
–
Puerto Rico: 1-866-664-6443
Before requesting support, please try to
reproduce and isolate the problem. When you
contact the Customer Care Center, be ready to
provide the following information:
beta.kyocera-wireless.com
.
•
•
The name of your service provider.
The actual error message or problem you
are experiencing.
•
•
The steps you took to reproduce the
problem.
The phone’s mobile equipment identifier
(MEID).
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Become a Product Evaluator
68
Index
Numerics
A
alerts
browser
C
call lists
B
battery
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
69
call timers
calls
D
E
F
G
groups
Download from Www.Somanuals.com. All Manuals Search And Download.
70
M
media files
menus
H
headsets
I
images
messages
K
keyguard
keypad
L
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
71
N
notifications
O
P
pages
phone
Download from Www.Somanuals.com. All Manuals Search And Download.
72
Q
sounds
R
ringers
roaming
speed dial list
S
T
settings
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
73
V
voicemail
volume
W
Download from Www.Somanuals.com. All Manuals Search And Download.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
75
Kyocera Communications Inc.
82-L2706-2EN, Rev. 001
Download from Www.Somanuals.com. All Manuals Search And Download.
|