INSTALLATION MANUAL
FOR THE
KC-SERIES
OF
SOLAR PHOTOVOLTAIC POWER MODULES
Please read this manual carefully before installing the modules.
KYOCERA CORPORATION
1. INTRODUCTION
As the world leader in development and application of high technology ceramic/silica materials, Kyocera Corporation
(KC) offers a wide range of highly efficient and reliable crystalline silicon solar photovoltaic (PV) power modules.
Kyocera began to extensively research PV technology in 1975 and commenced manufacturing operations in 1978.
Since then, Kyocera has supplied millions of cells and modules throughout the world. With years of experience and
state-of-the-art technology, Kyocera provides the highest quality PV power modules in a range of sizes designed to
meet the requirements of the most demanding energy and power users worldwide.
2. POWER MODULES
Kyocera power modules consist of a series of electrically interconnected crystalline silicon solar cells. Which are
permanently laminated within an ethylene-vinyl-acetate (EVA) pottant and encapsulated between a tempered glass
cover plate and a poly-vinyl-flouride (PVF) back sheet. The entire laminate is secured within an anodized aluminum
frame for structural strength, ease of installation, and to protect the cells from the most severe environmental
conditions.
3. APPLICATIONS
Kyocera modules are a reliable, virtually maintenance-free direct current (DC) power source, designed to operate most
efficiently in sunlight. Kyocera modules are ideal to power remote homes, recreational vehicles, water pumps,
telecommunication systems and many other applications either with or without the use of storage batteries.
4. WARNINGS
Solar modules generate electricity when exposed to light. Arrays of many modules can cause lethal shock and burn
hazards. Only authorized and trained personnel should have access to these modules. To reduce the risk of electrical
shock or burns, modules may be covered with an opaque material during installation to avoid shocks or burns. Do not
touch live terminals with bare hands. Use insulated tools for electrical connections.
PERMIT
・ Before installing your solar system, contact local authorities to determine the necessary permit, installation and
inspection requirements.
INSTALLATION AND OPERATION
・ Systems should be installed by qualified personnel only. The system involves electricity, and can be dangerous if
the personnel are not familiar with the appropriate safety procedures.
・ Do not step on the module.
・ Although KYOCERA modules are quite rugged, the glass can be broken (and the module will no longer work
properly) if it is dropped or hit by tools or other objects.
・ Sunlight shall not be concentrated on the module.
・ The module frame is made of anodized aluminum, and therefore corrosion can occur if the module is subject to a
salt water environment with contact to a rack of another type of metal.(Electrolysis Corrosion) If required, PVC or
stainless steel washers can be placed between the solar module frame and support structure to prevent this type of
Download from Www.Somanuals.com. All Manuals Search And Download.
7. INSTALLING KC MODULES
The frame of each module has 0.28”φ diameter (7 mm) mounting holes (Refer to Module Mounting Specifications).
These are used to secure the modules to the supporting structure. An example of a ground mounted structure is shown
in Figure 3. The four holes close to the corners of the module are most often used for attachment. Refer to the
Mounting Specification Specifications for the position of these holes. Clearance between the module frame and the
mounting surface may be required to prevent the junction box from touching the surface, and to circulate cooling air
around the back of the module. If the modules are to be installed on the roof or wall of a building, the standoff method
or the rack method is recommended.
STAND-OFF METHOD: The modules are supported
parallel to the surface of the building wall or roof.
Clearance between the module frames and surface of
the wall or roof is required to prevent wiring damage
MOUNTING HOLE
ARRAY FRAME
and to allow air to circulate behind the module.
The recommended stand-off height is 4.5 in. (about 115
mm) If other mounting means are employed, this may
affect the Listing For Fire Class Ratings.
SUPPORT
LEGS
MODULE
RACK:
The supporting frame is used to mount
modules at correct tilt angles. The modules are not
designed for integral mounting as part of a roof or wall.
The mounting design may have an impact on the fire
resistance.
FOOT ANGLE
Figure 2. Basic Rack or Standoff Mounting Structure
8. MODULE WIRING
As shown in Module Mounting Specifications, all of the KC modules utilize the Type G junction box except the KC-70,
KC-80 and KC-120-1 modules which utilize the Type M junction box (see J-box details). This junction box, located on
the back side of the module, is weatherproof and is designed to be used with standard wiring or conduit connections.
Kyocera recommends that all wiring and electrical connections comply with the 1999 National Electrical Code (NEC).
Bypass diodes and cable clamps are included with each module when shipped from the factory.
Figure 3. Standard Wiring Examples
To wire Kyocera modules:
A
Determine the nominal system array voltage of your system. Each panel is equivalent to a 12 VDC nominal block.
Standard array voltages 12, 24 and 48 volt are shown as examples in Figure 3.
B. Open the "G" or "M" box cover by loosening the screws in the cover.
Download from Www.Somanuals.com. All Manuals Search And Download.
C. The wire used to interconnect the solar modules
may be single or two conductor, from 14 AWG (2.08
mm2) up to 10 AWG (5.26 mm2) gauge stranded
copper wire, in a “SUNLIGHT RESISTANT” jacket
UF cable. This cable is suitable for applications
where wiring is exposed to the direct rays of the
sun. The maximum and minimum outer diameters
of the cable that may be used with the cable
connector are 8 mm and 6 mm respectively (Fig. 3).
D. Using a flat blade screwdriver, remove only the
appropriate "KNOCK-OUTS" from the sides of the
"G" or "M" box .
TERMINAL SCREW
SPRING WASHER
CABLE
CUP WASHER
Figure 4.
Ring or Spade Terminal Connectors
E. Route wires through the knock-outs and clamps in
the following steps (see Figure 5):
a. Insert the nipple (1) of the clamp in a hole in the
junction box using lock nut (2).
b. Push the interconnect cable (3) through (1), (2)
and the cap (4).
c. Clamp the cable by tightening the cap (4).
F. Gently hand tighten the terminal screws with cross
tip (Phillips head) screwdriver. Do not overtighten,
as the terminal can be damaged.
G. The output wiring from the final module is generally
run to a separate array junction box. In commercial
system, this wiring from the array box to the next
component (i.e. fuse box. or charge regulator, etc.)
is generally run in conduit. The maximum electrical
rating of an acceptable series fuse is 4～12
amperes.
Figure 5. Interconnect Cable Clamp
H. After checking that module wiring is correct, close and secure all the junction boxes. Use a Phillips head screw driver
to secure all screws on the junction box cover to ensure a waterproof seal.
9. GROUNDING
We recommend you attach all module frames to an earth ground. Attach a separate ground wire to one of the holes
marked ‘ground’ on the module frame with a screw and bonding or external tooth washer. This is to ensure positive
electrical contact with the frame. The racks must also be grounded unless they are mechanically connected by nuts
and bolts to the grounded modules.
Grounding is achieved by securing the array frame for both roof and field mounted applications. Additionally, the array
frame shall be grounded in accordance with NEC Art 250.
10. BLOCKING DIODES
Blocking diodes are typically placed between the battery and the PV module output to prevent battery discharge at
night. Kyocera modules are made of polycrystalline cells with high electrical “back flow” resistance to nighttime battery
discharging. As a result, KYOCERA modules do not contain a blocking diode when shipped from the factory. Most PV
charge regulators do have a nighttime disconnect feature, however.
11. BYPASS DIODES
Partial shading of an individual module in a 12 volt or higher source circuit string (i.e. two or more modules connected in
series) can cause a reverse voltage across the shaded module. Current is then forced through the shaded area by the
other modules.
Download from Www.Somanuals.com. All Manuals Search And Download.
When a bypass diode is wired in parallel with the series string, the forced current will flow through the diode and bypass
the shaded module, thereby minimizing module heating and array current losses.
For 12-volt systems and higher: Each module junction box has a diagram illustrating the proper orientation of the
bypass diode installed between two of the terminal screws (Figure 11, Figure 12). When the solar modules are
connected as individual series strings first, and then these strings are connected in parallel, bypass diodes should be
used in each junction box. This is the simplest wiring arrangement for most installations.
Diodes that are used as bypass diodes must:
・ Have a Rated Average Forward Current [IF(AV)] Above maximum system current at highest module operating
temperature.
・ Have a Rated Repetitive Peak Reverse Voltage [VRRM] Above maximum system voltage at lowest module
operating temperature.
12. MAINTENANCE
Kyocera modules are designed for long life and require very little maintenance. Under most weather conditions, normal
rainfall is sufficient to keep the module glass surface clean. If dirt build-up becomes excessive, clean the glass surface
only with a soft cloth using mild detergent and water. USE CAUTION WHEN CLEANING THE BACK SURFACE OF
THE MODULE TO AVOID PENETRATING THE PVF SHEET. Modules that are mounted flat (0°tilt angle) should be
cleaned more often, as they will not "self clean" as effectively as modules mounted at a 15°tilt or greater. Once a
year, check the tightness of terminal screws and the general condition of the wiring. Also, check to be sure that
mounting hardware is tight. Loose connections will result in a damaged module or array.
13. SPECIFICATIONS
The electrical and physical specifications can be found at the end of this document (Table 2).
NOTES
・ The electrical characteristics are within ±10 percent of indicated values of Isc, Voc, and Pmax under standard test
conditions (irradiance of 1KW/m2, AM 1.5 spectrum, and cell temperature of 25℃).
・ Under certain conditions, a photovoltaic module is likely to produce more current and / or voltage than reported at
standard test conditions. Accordingly, the values of Isc and Voc marked on this module should be multiplied by a
factor of 1.25 when determining component voltage ratings, conductor ampacities, fuse sizes, and sizes of
regulators which are connected to the PV output. Refer to Section 690-8 of the National Electrical Code for an
additional multiplying factor of 125 (80 per cent derating) which may also be applicable.
MANUFACTURED IN JAPAN BY KYOCERA CORPORATION
KFG GROUP
KSI GROUP
„ Kyocera Fineceramics GmBH
Fritz Müller Strasse 107, D-73730 Esslingen, Germany
Phone: (49) 711-9393-417
„ Kyocera Solar Inc. (Headquarters)
7812 East Acoma Drive, Scottsdale, AZ 85260, USA
Tel: (480) 948-8003 or (800) 223-9580
Fax: (480) 483-6431
Fax: (49) 711-9393-450
„ Kyocera Solar Pty, Ltd.
KAP GROUP
36 Windorah St., Unit 6 Stafford 4053 Queensland, Australia
Tel: (61) 7-3856-5388
Fax: (61) 7-3856-5443
„ Kyocera Asia Pacific Singapore
Fritz Müller Strasse 107, D-73730 Esslingen, Germany
298 Tiong Bahru Road, #13-03/05 Tiong Bahru Plaza Singapore
168730
„ Kyocera Solar Argentina S.A.
Tel: (65) 271-0500
Fax: (65) 271-0600
Mejico 2145, 16400 Martinez Prov. de Buenos Aires Argentina
Tel: (54) 114-836-1040
Fax: (54) 114-836-0808
„ Kyocera Solar Do Brazil
Rua Mauricio da Costa Faria, 85
22780-280 – Recreio – Rio de Janeiro
Tel: (55) 2-1554-5554
Fax: (55) 2-1553-4894
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 2. Kyocera KC-Family Module Specifications
Electrical Characteristics:
Model Number
KC-120-1
120
KC-80
80
KC-70
70
KC-60
60
KC-50
50
KC-45
45
KC-40
40
KC-35
35
Rated Power, Watts (Pmax)
Open circuit Voltage (Voc)
Short Circuit Current (Isc)
Voltage at Load (Vmp)
21.5
7.45
16.9
7.1
21.5
4.97
16.9
4.73
600
21.5
4.35
16.9
4.14
600
21.5
3.73
16.9
3.55
600
21.5
3.1
19.2
3.1
21.5
2.48
16.9
2.34
600
18.8
2.5
16.7
3
15
15
Current at Load (Imp)
3
2.33
N/A
yes (4)
6
Maximum System Voc
600
600
yes (4)
6
600
yes (4)
6
Factory Installed Bypass Diode (Qty)
Series Fuse Rating (Amps)
yes (6)
11
yes (6)
7
yes (6)
7
yes (4)
6
yes (4)
6
NOTE: The Electrical specifications are under test conditions of irradiance of 1kW/M2, Spectrum
of 1.5 air mass and cell temperature of 25oC
Physical Characteristics:
Model Number
KC-120-1
56.1
KC-80
38.4
KC-70
34.1
KC-60
29.6
KC-50
25.2
KC-45
22.6
KC-40
20.7
KC-35
18.5
Length, Inches (mm)
(1425)
(976)
25.7
(865)
25.7
(751)
25.7
(639)
25.7
(573)
25.7
(526)
25.7
(471)
25.7
Width, Inches (mm)
25.7 (652)
(652)
(652)
(652)
(652)
(652)
(652)
(652)
Depth (frame, Inches (mm)
Depth (including j-box), inches (mm)
Weight, Pounds (kg)
1.42 (36) 1.42 (36) 1.42 (36) 1.42 (36) 1.42 (36) 1.42 (36) 1.42 (36) 1.42 (36)
2.0 (52) 2.0 (52) 2.2 (56) 2.0 (52) 2.1 (54) 2.1 (54) 2.0 (52) 2.1 (54)
23.6 (11.9) 21.2 (9.6) 15.4 (7.0) 13.2 (6.0) 11.0 (5.0) 9.9 (4.5) 9.9 (4.5) 8.8 (4.0)
Mounting Hole Diameter, inches (mm) * 0.28" (7) 0.28" (7) 0.28" (7) 0.28" (7) 0.28" (7) 0.28" (7) 0.28" (7) 0.28" (7)
*Note: See Module Mounting Specifications for Hole Location on Frame
Download from Www.Somanuals.com. All Manuals Search And Download.
MODULE MOUNTING DIMENSIONS
DO NOT USE
DO NOT USE
KYOCERA KC−SERIES
MODULE MOUNTING SPECIFICATIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
|