Kustom Stereo Amplifier KGA30 User Manual

OWNER’S MANUAL  
KGA30  
Thank you for purchasing the Kustom KGA30 model guitar amplifier. Kustom has  
listened to musicians throughout the world and stands proudly behind each and every  
one we make. It was designed with your needs in mind. Feature laden, great sounding,  
able to adapt to all kinds of music, this amplifier really delivers what you have been  
looking and waiting for. Whatever style you choose, it’s ready !  
Kustom, with a 30 year tradition of excellence in design, proudly delivers to you this  
amp and rewards you with a rugged and dependable amp designed and engineered  
in the USA. Again, thank you for your purchase. Please take a few minutes to learn  
about all the professional features that are built in.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KGA30  
15  
1
3
5
2
4
6
7
8
9
10  
12  
14  
11  
13  
1.) CD/Tape Input - this 1/4” 3 conductor jack will allow you to plug in a CD player, tape or any other source to  
practice along with. It sums the left and right signals into a mono signal. To control the volume of the source,  
adjust the output volume of the device. We suggest you turn the volume all the way down then plug in and adjust  
the volume according to your taste.  
2.) Guitar Input Jack - this is a 1/4” 2 conductor input jack for plugging in your instrument. It is intended for  
guitars but will accept other instruments as well.  
3.) Lead Gain - adjust this clockwise to increase the amount of distortion you add to the overdrive signal. Used  
in the lower ranges of the control, you get a less distorted sound, a “bluesy” tone. As you increase the gain, you  
add tremendous amounts of distortion to the signal for a harder edged “crunch” tone.  
4.) Channel Switch - this switch selects which preamp you are using. It will switch between the Rhythm and  
Lead channels.  
5.) Lead Volume - this control is the output volume control for the Lead Channel. It follows the same tone circuit  
as the other channel. It’s gain structure is determined by the lead gain control but this serves as the overall  
master volume for this channel.  
6.) Rhythm Level - this is the volume control for the clean channel. It’s gain structure is preset for maximum  
signal before distortion and determines the output level of the amp.  
7.) Bass - this control is the bass control. It is passive and set to shelve frequencies at 65 Hz. This will effect  
the low frequency signals. Turning it fully clockwise, the signal is left alone. Turning it counterclockwise, the lows  
will be rolled off.  
8.) Mid - this control is the midrange control. It is passive and set to shelve frequencies at 1KHz. This will effect  
the middle frequency signals. Turning it counterclockwise, your signal will “hollow out” the mids which is popular  
in today’s music.  
9.) High - this control is the high control. It is passive and set to shelve frequencies at 5KHz. This will effect the  
high frequency signals. Turning it fully clockwise, the signal is left alone. Turning it counterclockwise, the highs  
will be rolled off.  
10.) Reverb Level - this control adds the spring reverb and mixes it into the main signal buss. Reverberation  
creates a trail like effect with the sound. It lets the notes “hang in the air” longer, extending the sound.  
11.) Chorus On/Off Switch - this is the switch to turn on and off the chorus circuit.  
12.) Chorus Level - this is the Speed Control for the chorus circuit.  
13) Headphone Jack - this is a 1/4” 3 conductor jack for plugging headphones. It will sum the signal and put  
the sound in both ears, thereby creating a pseudo-stereo sound. Volume will be determined by the volume control  
on the channel you are on. It will disconnect the internal speaker when plugged in. This will allow quiet practicing.  
14.) Jewel Light - this jewel light lets you know that the amplifier is on.  
15.) Power - this switch turns on and off the AC power to the amp.  
Back Panel - (not pictured)  
Speaker Out - this is a 2 conductor 1/4” speaker output jack. This will disconnect the internal speaker and allow  
an external speaker cabinet to be employed. Rating is 8 ohms.  
Line Output - this is a 2 conductor 1/4” line output jack. This will allow an external amplifier or mixing board to  
be supplied with the signal from this amp. This signal is attenuated and comes from the power amp.  
Effects Loop I/O - these are 2-2 conductor 1/4” jacks. This will allow an external effects device or equalizer to be  
patched back in before the power amp section in this amp. One is send and the other is return.  
Footswitch Jack - this is a 3 conductor 1/4” jack. This is for hooking up a footswitch to switch channels and to  
turn on/off the chorus.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Suggested Settings  
(These settings are general starting points. They  
are designed to get you close to the sound you are  
looking for. If the control is not shown, then it doesn’t  
apply to this particular sound. )  
Clean Rhythm or Country Guitar - these settings are the basic clean sounds and for  
general rhythm guitar, country lead guitar, funky/chunky rhythm sounds. Usually, country guitar  
is a brighter, more trebly edged sound. The bottom end depends on what type of guitar you are  
using. Reverb and Chorus depends on taste.  
Rhythm guitar is mostly a clean full type of sound. A little less treble than the country sound and  
a bit more midrange. Reverb and Chorus, again depends on taste.  
Blues Lead or Mellow Crunch - this setting is particularly useful in blues or softer rock  
songs and It is good for leads as well as rhythm parts. It is good for power chords in back of  
leads.You need to switch to the lead channel to make these settings work. Blues, depending on  
the guitar you use, usually adds treble but with more midrange and a “fat” bottom end. This  
setting does not have as much gain as full out crunch, adjust the gain control to the amount of  
distortion you desire. Blues usually has a reverb trail on the notes. Chorus is sometimes used  
to create a vibrato style sound. Adjust to taste.  
Alternative/Harder Edged Rock - this setting will deliver more of a cutting tone.  
Whether used for rhythm or lead sounds, it will “cut” through the drums and get you  
heard. If you need more “grundge”, increase the gain control for more distortion. This  
style of music requires a slightly thinner, harder edged tone full of midrange. Less  
reverb is required as it tends to muddy up faster songs but Chorus give the tone a fatter  
fuller sound. Adjust to taste.  
Heavy Metal/Maximum Crunch - this setting is a good starting point for the  
“notched out middle” sounds associated with metal and heavy alternative sounds.  
Adjust the Treble, Lows, Reverb and Chorus to taste. Usually, for a rhythm tone, you  
want to have more lower end and less for leads. Distortion is an integral part of this  
style of music and this amp delivers it quite well.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Land Pride Lawn Mower Z48 User Manual
LG Electronics Door NL 7000 AC User Manual
LG Electronics Microwave Oven LMV1683ST User Manual
Lincoln Electric Welding System IM692 User Manual
Linear Switch D 8C User Manual
Lowrance electronic Marine Instruments 000 0106 72 User Manual
Lucent Technologies Cordless Telephone 4406D+ User Manual
Magnavox CD Player AZ2605 17 User Manual
Melissa Toaster AT 280 User Manual
Mellerware Hair Dryer 2 0 1 0 0 User Manual