Thank you purchasing the Korg
ELECTRIBE·M EM-1. In order to
enjoy long and trouble-free use,
please read this manual carefully
and use the instrument correctly.
E 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1. Introduction ............................................................................. 6
Main features ................................................................................................................ 6
The data you create on the EM-1 ........................................................................................................ 6
Make connections and play! ........................................................................................7
Example connections................................................................................................................................ 7
Preparing to play ....................................................................................................................................... 7
2. Front and rear panel ............................................................... 8
Common section ...........................................................................................................8
Effect/Delay section ......................................................................................................9
Part common section....................................................................................................9
Synth filter section ..................................................................................................... 10
Part Select section ..................................................................................................... 10
Sequence Control section ......................................................................................... 10
Step Key section ........................................................................................................ 11
Connector section...................................................................................................... 12
3. Basic operation (Quick Start)................................................13
Conceptual diagram of the EM-1 .............................................................................. 13
Listening to a Song .................................................................................................... 13
Listening to Patterns.................................................................................................. 14
Trying out the functions ............................................................................................ 14
Changing the tempo of a song or pattern ............................................................................................ 14
• Using the dial to change the tempo ................................................................................................ 14
• Using the Tap Tempo key to change the tempo .............................................................................. 14
Pressing keys to play the sound of a Part............................................................................................ 15
Playing the sound of a drum part ...................................................................................................... 15
Playing the sound of a synth part (the Keyboard function) ............................................................... 15
Modifying (editing) the sound of a part ................................................................................................ 16
Editing the sound of a drum part ....................................................................................................... 16
Editing the sound of a synth part ....................................................................................................... 16
Editing the effect or delay ...................................................................................................................... 17
Playing the sound of a part along with a song or pattern .................................................................. 17
Editing the sound of a part, effect, or delay while hearing a song or pattern ................................. 18
Modifying (editing) a rhythm or phrase pattern ................................................................................... 18
Realtime recording ............................................................................................................................. 19
Step Recording .................................................................................................................................. 20
Saving a pattern that you create ............................................................................................................ 21
Using a Motion Sequence....................................................................................................................... 22
Playing with Pattern Set.......................................................................................................................... 23
Using the EM-1 as a tone generator module ........................................................................................ 23
Synchronizing the playback with other ELECTRIBE models ............................................................. 24
4. Pattern mode ..........................................................................25
Selecting a pattern ..................................................................................................... 25
Setting the playback tempo ...................................................................................... 25
• Using the dial to change the tempo .................................................................................................... 25
• Using the Tap Tempo key to change the tempo ................................................................................. 25
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing a pattern (Pattern Play) ................................................................................ 25
The timing at which patterns will change ............................................................................................. 25
Playing from the beginning of a pattern (Reset & Play) ..................................................................... 25
About the tempo when you switch patterns (Tempo Lock) ................................................................ 26
Selecting a part ........................................................................................................................................ 26
Drum parts ......................................................................................................................................... 26
Synth parts ......................................................................................................................................... 26
Accent parts ....................................................................................................................................... 26
The Part Mute function............................................................................................................................ 26
The Part Solo function ............................................................................................................................ 26
Creating a pattern ...................................................................................................... 27
Assigning a wave..................................................................................................................................... 27
Editing the sound of a part..................................................................................................................... 27
Drum part ........................................................................................................................................... 27
Synth part ........................................................................................................................................... 28
Accent parts ....................................................................................................................................... 28
Editing the effect or delay ...................................................................................................................... 29
EFFECT ............................................................................................................................................. 29
DELAY ................................................................................................................................................ 30
Length, Scale/Beat settings ................................................................................................................... 31
Setting the Length .............................................................................................................................. 31
Setting the Scale/Beat ....................................................................................................................... 31
Swing settings ......................................................................................................................................... 32
Setting the Roll Type ............................................................................................................................... 32
Creating a Pattern .................................................................................................................................... 32
Realtime recording ............................................................................................................................. 32
Step recording .................................................................................................................................... 32
Note editing ........................................................................................................................................ 32
Adding accents to the pattern (Accent) ................................................................................................ 34
Motion sequence ........................................................................................................ 34
Playing a motion sequence .................................................................................................................... 34
Recording a motion sequence ............................................................................................................... 35
Checking motion sequence data ........................................................................................................... 35
Convenient functions for editing patterns............................................................... 35
Transposing a phrase (Transpose) ........................................................................................................ 35
Moving data within a part (Move Data) ................................................................................................. 36
Copying a part (Copy Part) ..................................................................................................................... 37
Data Copy within a pattern ..................................................................................................................... 37
Copying the sound of a part (Copy Sound) ........................................................................................ 37
Erasing motion sequence data from the part, effect, or delay (Clear Motion) ................................. 38
Erasing pattern data from a part............................................................................................................ 38
Erasing data during playback or recording (Erase) ........................................................................... 38
Erasing all data from a part (Clear Part) ........................................................................................... 38
Exchanging data between parts (Swap Part) ....................................................................................... 39
Editing motion sequence data .................................................................................. 39
Selecting a motion sequence ................................................................................................................. 39
Editing the parameter values of a motion sequence .......................................................................... 40
Pattern Set................................................................................................................... 40
Using Pattern Set to perform (Pattern Set Play) .................................................................................. 40
Chain Play of pattern sets.................................................................................................................. 40
Assigning a pattern to a Pattern Set ..................................................................................................... 41
Saving a pattern (WRITE) .......................................................................................... 41
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Song mode .............................................................................42
Selecting a song......................................................................................................... 42
Setting the playback tempo ...................................................................................... 42
• Using the dial to set the tempo ........................................................................................................... 42
• Using the tap tempo key to set the tempo ......................................................................................... 42
• Using the Tempo Lock key to fix the song tempo ............................................................................. 42
Playing a song (Song Play) ....................................................................................... 42
Fast-forward or rewind a song ............................................................................................................... 42
Switching songs ...................................................................................................................................... 42
Playing from the beginning of a position or song (Reset & Play) ..................................................... 42
Creating a song .......................................................................................................... 43
Creating a song from scratch ................................................................................................................ 43
Erasing song data (Clear Song) ........................................................................................................ 43
Specifying a pattern for each position ............................................................................................... 43
Specifying the Note of each pattern ...................................................................................................... 43
Editing a song .......................................................................................................................................... 44
Inserting a pattern at a specified position (Insert Pattern)................................................................ 44
Deleting a pattern from a specified position (Delete Pattern) ........................................................... 44
Changing the pattern for a specific position ...................................................................................... 44
Recording knob movements or your performance in a song (Event Recording).............................. 45
Deleting event data from a song ........................................................................................................ 45
Checking for song event data ............................................................................................................ 45
Saving a song (WRITE) .............................................................................................. 45
6. Global mode ...........................................................................46
Metronome settings ................................................................................................... 46
Synchronizing the EM-1 with external MIDI devices (MIDI Clock) ........................ 46
Synchronizing the EM-1 to a master external MIDI device (Ext) ........................................................ 46
Synchronizing an external MIDI device to the EM-1 as master (int).................................................. 46
Setting the MIDI channel of each part (MIDI ch) ..................................................... 47
Setting the MIDI note number of a drum part.......................................................... 47
MIDI filter settings ...................................................................................................... 47
Adjusting the pitch bend range ................................................................................ 47
Transmit/receive dump data...................................................................................... 48
Memory Protect (Protect) .......................................................................................... 48
Saving your changes in Global mode (WRITE) ....................................................... 48
7. Appendices.............................................................................49
About MIDI .................................................................................................................. 49
Troubleshooting ......................................................................................................... 50
Error messages .......................................................................................................... 51
Restoring the factory set data .................................................................................. 51
Specifications ............................................................................................................. 51
Index ............................................................................................................................ 52
Pattern Name List ....................................................................................................... 54
Song Name List .......................................................................................................... 54
MIDI Implementation Chart ....................................................................................... 55
Wave Name List .......................................................................................................... 56
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
1. Introduction
Thank you for purchasing the ELECTRIBE• M(subsequently referred to as the EM-1).
The EM-1 is a production station designed for dance music that makes it easy for anyone from
beginner to enthusiast to create original music.
You can edit sounds intuitively by using the front panel knobs and keys, and easily create
complete rhythms and phrase patterns without requiring any additional equipment.
The EM-1 is the ideal tool for any musician, DJ, sound creator, or DTM user who wants an
easy way to add originality to their music.
Main features
• The EM-1 has eight drum parts and two synth parts, and you can assign sounds to each
part and edit them.
• By combining rhythm patterns created for each drum part together with phrase patterns
created for each synth part, you can easily create a song using no additional equipment.
• Internal memory contains numerous drum waves (144 types) and synth waves (50 types),
giving you access to a wide range of sonic expression.
• Up to 256 patterns (maximum of 64 steps each) can be created using the Sample data
and stored in internal memory.
• The EM-1 provides a Motion Sequence function that can record and loop knob move-
ments, and can be recorded for each part of each pattern.
• By combining multiple patterns and adding event data such as knob movements, you
can create and save up to sixteen songs.
• You can choose from realtime recording, step recording, and note editing.
• Since sounds and rhythm or phrase patterns can be modified instantly, you can use
these changes as part of your live performance expression.
• Eleven types of effect plus tempo delay are provided, and an Effect/ Delay Motion Sequence
function allows knob movements to be recorded.
• A Keyboard function lets you use the sixteen step keys as a keyboard on which to perform.
• The Pattern Set play function lets you assign 64 different patterns to the 16 step keys,
and successively select and play them.
• Tap Tempo and MIDI Clock can be used to synchronize the performance with an exter-
nal sequencer, turntable, etc.
• The EM-1 can be controlled from an external sequencer or keyboard as a MIDI sound
module.
• The MIDI Dump function lets you save data on a computer or external sequencer etc.
The data you create on the EM-1
Patterns and songs that you create on the EM-1 by editing will return to their un-edited state
if you select a different pattern or song, or turn off the power before performing the Write
operation. If you wish to save an edited pattern, song, or global data, be sure to perform the
Write operation. Even after Writing the edited data, it is still possible to restore all songs and
patterns etc. to the factory settings. (Refer to p.51 “Restoring the factory set data.”)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Make connections and play!
Example connections
Preparing to play
Be sure to turn off the power before making connections. Careless operation may damage
your speaker system or cause malfunctions.
As shown in the above diagram, hook the AC adapter cable around the adapter cable holder.
When removing the cable from the holder, do not use excessive force.
1. Connect the included AC adapter to the DC 9V jack, and plug the adapter into an AC
outlet.
2. Connect one end of your audio cables to the line out jacks of the EM-1 (L/MONO, R), and
connect the other end to your mixer or powered monitor speakers (amplified speakers) etc.
If you will be listening in mono, use the L/MONO jack. To take full advantage of the EM-1's
sound quality, we recommend that you listen in stereo.
3. If you will be using headphones, connect them to the headphone jack.
The output from the line out jacks will not be switched off even if headphones are plugged in.
4. When you have finished making connections, turn on the power. Slightly raise the master
volume of the EM-1, and strike the Drum part keys (1...6B) to check whether connections
have been made correctly. Use the master volume of the EM-1 and the gain and fader con-
trols of your mixer or powered monitor system to adjust the volume to an appropriate
level.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.Front and rear panel
2. Front and rear panel
The controls and other parts of the
EM-1 can be broadly grouped as
shown in the diagram.
Common section
1. MASTER VOLUME
1
2
This knob adjusts the volume that is output from
the line out jacks and the headphone jacks.
4
3
5
2. Tempo Lock
6
When this key is on, the tempo will not change
when you select different patterns.
7
3. Display
This shows the value of the currently selected pa-
rameter, and various messages.
10
8
9
4. D ial
Use this to modify the value shown in the display.
5. MIDI (LED)
This will light when valid MIDI messages are received.
6. Beat (LED)
This will blink at quarter-note intervals to indicate the tempo.
7. [L][L] (cursor keys)
In each mode, use these keys to select parameters from the matrix shown in the display.
8. Matrix
The parameters that will appear in the display are listed here for each mode. Use the
cursor keys to make the desired parameter select LED light.
9. Mode keys
These keys are used to select PATTERN, STEP EDIT , SONG, or GLOBALmodes.
10. WRITE key
Use this key when you wish to save settings that you modified in Pattern, Song, or
Global mode, or to save Pattern Set data.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2.Front and rear panel
Effect/Delay section
1. Type
Selects the effect type.
5
1
2
2. Original Value (LED)
This will light when the knob etc. that you are currently moving
arrives at the same position as originally programmed in the
pattern.
6
4
3
3. Delay Edit key
Each time you press this key, Delay Edit will be turned on (lit) or off (dark). When this
is on, you can use the Edit 1 and 2 knobs to control the delay. When you use the Type
knob to switch effects, this will be forced off.
4. Motion Seq (motion sequence) key
Each time you press this key, it will be turned on (lit) or off (dark). When this is on,
movements of the Edit 1 and 2 knobs will be recorded and played back. When Delay
Edit is on, Delay motion sequence will be selected. When Delay Edit is off, the motion
sequence of the effect selected by Type will be selected.
5. Edit 1/T ime
This knob adjusts the character of the effect. The result will differ according to the effect
type. When the Delay Edit key is on, this knob adjusts the length of the delay time.
6. Edit2/Depth
This knob adjusts the character of the effect. The result will differ according to the effect
type. When the Delay Edit key is on, this knob adjusts the depth of the delay.
Part common section
1. Motion Seq (motion sequence)
This key lets you record and play back knob movements
for each part. Each time you press this key, the setting
2
6
8
5
7
will alternate between on (Smooth lit), on (Trig Hold lit),
3
4
and off (dark)
1
2. Amp EG
Select the amp envelope for each part. Each time you press
this key, the envelope will switch between a decaying envelope “ ” (key lit) and a
sustaining envelope “ ” (key dark).
3. Roll
For each part, this key switches the roll effect (successive strikes) on (lit) or off (dark).
4. Effect
For each part, this key switches the effect send on (lit) or off (dark).
5. EG Time
This knob adjusts the envelope time (the time until the sound disappears) for each part.
6. Pitch/Glide
This knob sets the pitch of the drum part. For a synth part, it sets the time over which
the pitch will change smoothly between two notes.
7. Level
This knob adjusts the level. For the Accent part, it adjusts the accent level.
8. Pan (panpot)
This knob sets the stereo location of the sound.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2.Front and rear panel
Synth filter section
These controls let you adjust the brightness of the sound or add a distinctive
tonal character.
2
4
1
3
1. Cutoff
Adjust the cutoff frequency of the filter.
3. Resonance
Adjust the resonance of the filter.
2. EG Int (EG intensity)
Adjust the depth of the filter envelope.
4. Drive
Adjust the degree of distortion for the sound of the filter. Driver makes between warmly
Analog Overdrive and Hard Distortion.
Part Select section
1. (Synth Part) 1, 2 keys
1
These keys select a synth part
2
2. (Synth Part) Accent key
3
This key selects the synth accent part.
4
3. (Drum Part) 1—4, 5A-5B, 6A-6B keys
These keys select a drum part. By pressing a key, you can
hear the sound that is assigned to the corresponding part.
4. (Drum Part) Accent key
This key selects the drum accent part.
Sequence Control section
1
2
3
4
5
1. Rec key
Use this key to record rhythms, phrases and movements
of the knobs etc. If you press this key during recording,
recording will end, and playback will continue.
2. Stop/Cancel key
This key stops playback of a pattern or song, or cancels an operation.
3. Play/Pause key
This key begins/ pauses playback of a pattern or song.
4. TAP, Rest/T ie, Part Mute key
Tap on this key to enter a new tempo. During step recording, use this key to input a rest
or a tie. During playback, you can hold down this key and press a Part key to mute the
specified part.
5. Transpose, Solo key
Use this key to transpose a phrase. During playback, you can hold down this key and
press one or more Part keys to playback the specified part(s).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2.Front and rear panel
Step Key section
1
2
3
4
5
1. Select keys
By pressing these keys to turn the Select LEDs on or off, you can use the sixteen step
keys below as up to 64 step keys.
When the Keyboard function is on, these keys are used to switch the octave.
In Song mode, these keys function as rewind and fast-forward keys. When the Pattern
Set function is on, they are used to switch Pattern Set groups.
2. Select LEDs
The upper row of LEDs (green) indicates the location (length 1...4) within the pattern of
the currently-playing pattern.
The lower row of LEDs (red) indicates the location (length 1...4) of the pattern indicated
by the step keys. When the Pattern Set function is on, these LEDs indicate the pattern
set group. When the Keyboard function is on, these LEDs indicate the octave position.
3. Step keys 1...16
Use these keys to modify and audition the rhythm or phrase pattern of each part.
When the Keyboard function key is on, these keys function as a keyboard, allowing
you to play sounds. When the Pattern Set function is on, use these keys to select pat-
terns that you have assigned.
4. Keyboard, Pattern Set key
This makes the sixteen step keys function as a keyboard. Each time you press this key,
the setting will alternate on/ off. By holding down this key and pressing one of the step
keys, you can switch to the pattern that you assigned to that key (Pattern Set function).
5. Shift key
This key is used in conjunction with other keys. When held down, it gives an additional
function to another key.
Shift + Play/Pause key:Playback from the beginning of the pattern.
Shift + Rec key:During playback, erase triggers from the pattern.
Shift + Step keys:Execute the function shown below each step key.
For other Shift key combinations, refer to the explanation of each parameter.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2.Parts
Connector section
1
2
3
5
4
6
1. Power switch
This switch turns the power on/ off. Each time you press it, the power will alternate on
or off.
2. DC 9V
Connect the included AC adapter here.
3. Adapter cable holder
Hook the adapter cable around this so that it will not be disconnected accidentally.
4. MIDI connectors
IN
MIDI data is received at this connector to control the EM-1 from an external
MIDI device or to receive a data dump.
O UT MIDI data is transmitted from this connector to control an external MIDI de
vice or to transmit a data dump.
TH RU MIDI data received at the MIDI INconnector is re-transmitted without change
from this connector. This is used to "daisy-chain" multiple MIDI devices.
5. L/MONO, R (line output) jacks
Connect your audio cables from these jacks to your mixer or powered monitor system
(powered speakers) etc. If you wish to make monaural connections, connect the L/
MONO jack.
6.
(headphone jack)
A set of stereo headphones fitted with a stereo jack plug can be connected here.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operation (Quick Start)
3. Basic operation (Quick Start)
Conceptual diagram of the EM-1
On the EM-1 , a song contains both Patterns (which consist of Parts, and effect and
delay settings) and event data (refer to p.45 "Recording knob movements or your per-
formance in a song (Event Recording)").
Listening to a Song
1.Press the Song Mode key to enter Song mode (the key will light).
2.Use the cursor [L][L] keys to select Song (the top LED will light).
3. Rotatethedialtoselectthedesiredsong(S.01...S.16
).
4.Press the Play/ Pause key to playback the song (the key will light). When
the song ends, playback will stop automatically (the key will go dark).
To pause during playback, press the Play/ Pause key (the key will blink).
To resume playback, press the Play/ Pause key once again (the key will
light). To stop playback, press the Stop/ Cancel key.
It is not possible to change songs during playback.
What is a Song?
On the EM-1, a song is musical data consisting of Pat-
terns arranged in the desired playback order. The EM-1
lets you create and store up to sixteen songs. In each song
you can arrange up to 256 patterns, and rhythm , phrase
and knob movements can also be recorded in addition
to the playback. (Refer to p.42 "Song mode.")
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operation (Quick Start)
Listening to Patterns
1.Press the Pattern mode key to enter Pattern mode (the key will light).
2.Use the cursor [L][L] keys to select Pattern (the corresponding LED
will light).
3. Rotatethedialtoselectthedesiredpattern(A.01...A.64,b.01...b.64,
d64Cd.0160.41,.
.)
4.Press the Play/ Pause key to playback the pattern (the key will light).
When pattern playback ends, the pattern will return to the beginning,
and continue playing repeatedly.
To pause during playback, press the Play/ Pause key (the key will blink). To resume
playback, press the Play/ Pause key once again (the key will light). To stop playback,
press the Stop/ Cancel key.
You can rotate the dial to select patterns when playback is stopped or even during
playback.
When you change patterns during playback, the change will actually occur at the
end of each pattern. (Refer to p.25 "The timing at which patterns will change.")
Depending on the effect and delay settings, slight
Pattern
noise or unwanted sound may occur at the transition
between patterns if they are changed during playback.
What is a Pattern?
A pattern is a performance of a specific length that consists of drum
sounds played as a rhythm, together with synth sounds played as
a phrase. The EM-1 lets you create and store 256 patterns. Each
pattern consists of 12 parts (see p.15). In addition to the sounds of
each part, you can also record phrases and knob movements (see
p.25 “Pattern mode”).
Trying out the functions
Changing the tempo of a song or pattern
There are two ways to change the tempo. When the Tempo Lock key is off
(key dark), switching patterns or songs will cause the tempo you set here to
return to the tempo of the selected pattern or song.
• Using the dial to change the tempo
1. Press the Mode key to enter Song mode or Pattern mode.
2. Use the cursor [L][L] keys to select Tempo (the corresponding LED will
light).
3. Rotate the dial to change the tempo.
If you wish to adjust the tempo in more detail, you can hold down the Shift
key and rotate the dial to modify the decimal portion of the value.
• Using the Tap Tempo key to change the tempo
While a song or pattern is playing, press the Tap key three times or more at
the desired tempo. The EM-1 will detect the interval at which you pressed
the Tap key, and will set the tempo accordingly. The tempo can also be changed
in this way even if the EM-1 is not currently playing a song or pattern.
Use the cursor [L][L] keys to select Tempo (the corresponding LED will
light),and the tempo you modified will appear in the display.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operation (Quick Start)
Pressing keys to play the sound of a Part
When you strike the drum part keys, or select a synth part, turn on the keyboard func-
tion and press the step keys, the sound of the corresponding part will be heard.
The sound of a part will differ depending on the pattern. Turn the dial to select various
parts, and listen to the wide variety of sounds.
When you press a drum part key, the keyboard function of the step keys will be
cancelled, but when you select a synth part once again, the keyboard function will
automatically return to the previous setting.
Parts for which Wave (see p.16 “What is a wave?”) is turned “oFF” cannot produce
sound.
What is a Part?
A part is the smallest unit of which a pattern is made, and consists of a
sound and rhythm or phrase, effect on/ off settings, and motion se-
quences etc. Parts can be one of the following types, and there are a total
of 12 parts. (See p.25 “Pattern mode”)
• Drum parts (1—4, 5A-B, 6A-B)
A drum sound and rhythm pattern (timing of sounds), effect on/ off,
motion sequence etc.
• Synth parts (1, 2)
A synth sound and phrase pattern (trigger, note number, gate time),
effect on/ off, motion sequence etc.
• Accent part (drum, synth)
Points at which to emphasize the volume of the pattern (i.e., accent), motion sequence.
The sound can also be edited for each part, and you can also store the rhythm, phrase
pattern, effect on/ off, and motion sequence etc. for each part. (See p.27 “Editing the
sound of a part”)
Playing the sound of a drum part
When you press drum part keys 1 through 6B, the sound assigned to each key will be
heard. (For each pattern, a different drum sound is assigned to each key.)
Pressing the drum accent part key will not produce sound. It is not possible to simul-
taneous play drum parts 5A and 5B or 6A and 6B - these parts are intended for
sounds which you want to cut each other off, like open and closed hi-hat etc..
Playing the sound of a synth part (the Keyboard function)
1.Turn on either synth part key 1 or 2 (the key will light).
2.Press the Keyboard key to turn on the Keyboard func-
tion (the key will light).
3.The step keys will function as a keyboard, and can be
played.
To change the octave, use the Select keys. The select LEDs
(lower row, red) will light to indicate the octave as fol-
lows.
LED(s) lit
Pitch range
Pressing the synth accent part key will not produce sound.
The Keyboard function cannot be turned on/off unless either synth part key 1 or 2 is
selected.
Each synth part is a monophonic synthesizer, and cannot play multiple notes simul-
taneously; i.e., it is not polyphonic.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operation (Quick Start)
Modifying (editing) the sound of a part
For a drum part you can select the wave of the drum sound, and for a synth part you
can select the wave of the synth sound.
Use the Level and Pan knobs and the Effect and Amp EG keys to edit the sound of each
part.
The sound of each part in the pattern that you edit in this way can be saved by the Write
operation. (See p.21 “Saving a pattern that you create.”)
When you press a drum part key, the keyboard function of the step keys will be
defeated, but will return to the previous setting when you once again select a synth
part.
The knobs that are valid will differ depending on the part. (See p.27 “Editing the
sound of a part.”)
If a motion sequence is operating for a knob and you have difficulty editing the sound
as you wish, turn off the motion sequence before editing the sound. (See p.34 “Mo-
tion sequence.”)
What is a Wave?
“Waves” are the pieces of waveform data inside the EM-1 that are the basis for the sound of each part.
There are 144 waves for use by drum parts, and 50 waves for use by synth parts, making a total of 194
waves. You can freely assign these waves to each part. (See p.27 “Assigning a wave”)
Editing the sound of a drum part
1.Press the PATTERN mode key to enter Pattern Mode.
2.Use the cursor keys [L][L] to select Wave (the corre-
sponding LED wil light).
3.Press a Drum Part key to select the part that you wish
to edit.
4.Turn the dial to select a wave while you press the key
you selected in step 3 to hear the sound.
5.Operate the knobs and keys of the Part Common sec-
tion to modify the sound. When a knob position or key
setting is the same as the original sound, the Original
Value LED
will light to indicate this.
Editing the sound of a synth part
1.Press the PATTERN mode key to enter Pattern mode.
2.Use the cursor keys [L][L] to select Wave (the corresponding LED wil light).
3.Use the Synth Part keys to select the part (1 or 2) whose sound you wish to edit.
4.Turn on the Keyboard function (the key will be lit),
and then press a step key to play the sound.
5.While pressing the step keys to hear the sound, turn
the dial to select a wave.
6.Operate the knobs and keys of the Synth Filter sec-
tion or the Part Common section to modify the sound.
When a knob position or key setting is the same as
theoriginalsound,theOriginalValueLED
willlight
to indicate this.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operation (Quick Start)
Editing the effect or delay
1.Press a drum part key to select a part for which it will be easy to hear the changes you
make to the effect.
2.To use a synth part while editing the effect, turn on the
Keyboard key, and press the step keys to play the sound.
3.To edit the effect, turn on the Effect key in the Part Com-
mon section (the key will light).
4.To edit the global delay, turn on the Delay Edit key in the
Effect/ Delay section.
5.Operate the knobs and keys of the Effect/ Delay section to
modify the effect or delay. When a knob position or key
setting is the same as the original effect or delay setting,
theOriginalValueLED
willlighttoindicatethis.
The pattern that you edit in this way can be saved by the Write operation (see p.21
“Saving a pattern that you create”).
When you press a drum part key, the keyboard function of the step keys will be
defeated, but will return to the previous setting when you once again select a synth
part.
The delay is a global effect, so it will always be on, regardless of the on/off status of
the Effect key.
The function of the knobs will differ depending on the type of effect. (See p.29 “EF-
FECT.”)
If a motion sequence is operating for a knob and you have difficulty editing the sound
as you wish, turn off the motion sequence before editing the sound. (See p.34 “Mo-
tion sequence.”)
Playing the sound of a part along with a song or pattern
1.Select the synth part (1 or 2) that you wish to play, and turn on the keyboard function.
2.In Song mode or Pattern mode, press the Play/ Pause key to begin playback.
3.Press the drum part keys or the step keys to play along
with the song or pattern.
When you press a drum part key, the keyboard func-
tion of the step keys will be defeated, but will return
to the previous setting when you once again select
a synth part.
The synth parts are monophonic synthesizers. One
part cannot sound multiple notes simultaneously.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operation (Quick Start)
Editing the sound of a part, effect, or delay while hearing a
song or pattern
1.In either Song mode or Pattern mode, press the Play/ Pause key to begin playback.
2.Press a part key (the key will light) to select the part that
you wish to edit.
3.Operate the knobs and keys of the Synth Filter section
or Part Common section to modify the sound. Operate
the knobs and keys of the Effect/ Delay section to modify
the effect or delay.
Operating the knobs or keys will modify the sound that is
used by the performance.
If you wish to save the pattern sound settings that you
edit here, use the Write procedure (see p.21 “Saving a pat-
tern that you create”)
If you re-select the pattern or turn off the power without performing the Write proce-
dure, the sound will return to its un-edited state.
When you press a drum part key, the keyboard function of the step keys will be
defeated, but will return to the previous setting when you once again select a synth
part.
While a Song is playing, it is not possible to write edits made to the part sound,
effect, or delay. It is only possible to write edits made to the part sound while a
Pattern is playing.
Modifying (editing) a rhythm or phrase pattern
Rhythm pattern
Rhythm patterns and phrase patterns
Each pattern of the EM-1 contains a rhythm pattern created using
the drum parts, and phrase patterns created using the synth parts.
The rhythm pattern consists of sequence patterns (note timing
data) for each step of each part.
Phrase patterns consist of trigger (note location), note number
(pitch), and gate time (note length) data at each step for each part.
Phrase pattern
You can use the sixteen step keys to modify the rhythm and phrase
patterns for the various parts. Rhythm and phrase patterns can
also be recorded (by realtime recording) as you play. (See p.25
“Pattern mode”)
As described below, there are two ways to edit a rhythm
pattern, and three ways to edit a phrase.
• Realtime recording
While playing back a pattern, you can use the part keys or the keyboard function (for
synth parts only) to record a new phrase along with the playback.
• Step recording
You can use the step keys to create a sequence pattern, or individually input the pitch
and length of each note to record a new phrase.
• Note editing (only for phrase patterns)
You can edit the data (trigger, note number, gate time) of the selected step to create a
phrase.
In the following pages we will explain how to perform Realtime Recording and Step
Recording. For details on Note Editing, refer to Note Editing (p.32) in "Pattern mode."
18
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operation (Quick Start)
Realtime recording
This method allows you to record while listening to the performance.
To record a rhythm pattern, press the rhythm part keys at the desired timing. To record
a phrase pattern, use the keyboard function and press the step keys at the desired tim-
ing.
When you press a drum part key, the keyboard function of the step keys will be
defeated, but will return to the previous setting when you once again select a synth
part.
If you wish to listen to the metronome as you record, refer to p.46 "Metronome set-
tings."
1.Press the Pattern mode key (the key will light). Use the
cursor [L][L] keys to select Pattern (the corresponding
LED will light).
2.Turn the dial to select the pattern that you wish to record.
3.To record a synth part, select either synth part 1 or 2,
and turn the Keyboard key on (the key will light).
4.Press the Rec key to enter record-ready mode. (The Rec
key will light, and the Play/ Pause key will blink.)
5.Press the Play/ Pause key to start the pattern. (The Play/
Pause key will light.)
6.To record a drum part, press the drum part key at the timing at which you want it to
sound.
7.To record a synth part, press the step key for the desired pitch at the timing at which
you want it to sound.
8.The pattern will playback repeatedly, and you can continue recording additional notes
as long as the Rec key is lit.
Press the Stop/ Cancel key to stop recorded. (The Rec key and the Play/ Pause key will
go dark.) Alternatively, you can press the Rec key (instead of pressing the Stop/ Cancel
key) to stop recording but continue playback. (The Rec key will go dark, and the Play/
Pause key will light.)
If you wish to save the completed pattern, press the Write key. (Refer to p.21 "Saving a
pattern that you create.")
Erase
If you input a note by mistake, hold down the Shift key while the pattern continues to
play, and then hold down the Rec key. Note triggers will be erased from the selected
part (whose key is lit) while you hold down these keys.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operation (Quick Start)
Step Recording
The method will differ, depending on whether you are creating a synth part phrase or a
drum part rhythm.
When you press a drum part key, the keyboard function of the step keys will be
defeated, but will return to the previous setting when you once again select a synth
part.
Using the step keys to create a drum part rhythm
1.Press the Pattern mode key (the key will light).
Use the cursor [L][L] keys to select Pattern (the corre-
sponding LED will light).
2.Rotate the dial to select the pattern that you wish to
record into.
3.Press a part key (the key will light) to select the part that
you wish to use.
4.The step keys will light to indicate the rhythm of the
selected part. You can press the step keys to modify the
rhythm pattern. Each time you press a key, it will alter-
nate between on (lit) and off (dark).
Using the step keys to create a synth part phrase
If the EM-1 is playing, press the Stop/ Cancel key to stop playback.
1.Press the Pattern mode key (the key will light). Use the cursor [L][L]
keys to select Pattern (the corresponding LED will light).
2.Rotate the dial to select the pattern that you wish to record into.
3.Turn on the Keyboard function (the key will light).
4.Use the Part Select key to select the part that you wish to use.
5.Press the Pattern mode STEP EDIT key, and then use the cursor keys
[L][L] to make the parameter select Step Rec (the corresponding
LED will light). The display will indicate the target step (see p.33).
6.Press the Rec key to enter recording mode. At this time, pressing the
Play/ Pause key will not start playback.
7.Use the step keys to input the pitch for each note of the phrase. (The
target step will automatically advance by one step each time you do
so.)
8.Recording will end when you input the last step or press the
Stop/ Cancel key (the Rec key will go dark).
To input a rest, press the Rest/ Tie key. To enter a tie, continue holding
down the step key (the sound will continue) and press the Rest/ Tie key.
During recording, you can rotate the dial to move the target step forward or backward.
You can jump to a specific step by holding down the Shift key and pressing the desired
step key.
In step recording, the trigger and note number are recorded simultaneously, but it is
not possible to make detailed settings for the gate time. Use Note Edit (refer to p.32
"Note editing") to re-adjust the trigger and note number, or to adjust the gate time.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operation (Quick Start)
In the case of a pattern with a length of 2 measures or greater, you can use the Select
keys to move the select LED in the lower line (red) in order to change the step location
that is shown by the step keys.
If you wish to save the completed pattern, press the WRITE key. (Refer to p.21 “Saving
a pattern that you create.”)
What is Length?
In this context, “Length” refers to the length of the rhythm
pattern. The “Length” of the pattern will be either 16 steps
or 12 steps, depending on the Scale and Beat settings of the
pattern. A rhythm pattern in triple meter will be shown in
triplets. Depending on the Length and Beat settings, a single
pattern can have up to 64 steps. (Refer to p.31 “Length,
Scale/ Beat settings.”)
Saving a pattern that you create
With the factory settings, memory protect will be on, and it will not be possible to
save data. Before you save data, you must turn off the Memory Protect settings in
Global mode. (Refer to p.48 "Memory Protect (Protect).")
Please be aware that when you save data, the pattern in the save destination will be
overwritten.
1.Edit a pattern as described in "Modifying (editing) the sound of a part" or "Modifying
(editing) a rhythm or phrase pattern."
2.Press the Write key once (the key will blink). The display will blink to indicate the
pattern number.
3.Rotate the dial to select the pattern number in which the data will be saved
(i.e., the "save destination").
4.Press the Write key once again to begin saving the data. While the data is
being saved, the key will blink. When saving is complete, the key will go
dark.
If you decide to cancel, press the Stop/ Cancel key. If you do not wish to save
the pattern you created, simply select a different pattern without performing
the Write operation.
Never turn off the power while data is being saved to memory (i.e., while the Write
key is lit). Doing so may damage the data.
It is not possible to Write data during playback or recording.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operation (Quick Start)
Using a Motion Sequence
What is a Motion Sequence?
The EM-1 has three types of motion sequence that let you record and loop tonal changes created by the
knobs and keys. (See p.35 “Recording a motion sequence”)
The knobs and keys that are valid for each of the three types of motion sequence (effect, delay, part) will
differ depending on the type of part.
Effect
Delay
Edit 1, Edit 2 (valid only for parts for which the effect is on)
Time, Depth (Applies to the entire pattern. Cannot be applied to an individual part.)
Drum part A total of two: either EG Time, Pitch, Level, or Pan; plus either Effect, Roll, or Amp EG
Synth part A total of three: either EG Time, Glide, Level, or Pan; plus either Cutoff, Resonance, EG
Int, or Drive; plus either Effect, Roll, or Amp EG
Accent part Level
As an example, here's how to record the Pitch parameter in a motion sequence.
1.In Pattern mode, select the pattern that you wish to edit.
2.Press the Drum Part key to select the part that you wish to edit.
3.Press the Motion Sequence key to select either Smooth
or Trig Hold
.
4.Press the Rec key to enter record-ready mode (the Rec
key will light, and the Play/ Pause key will blink).
5.Press the Play/ Pause key to start the pattern (the Rec
key and Play/ Pause key will light).
6.Move the Pitch knob to create various changes while
the pattern makes one cycle (16 steps x length, or 12
steps x length).
7.When the pattern has completed one cycle after you
began moving the knob, the Rec key will automati-
cally go dark and you will return to Play mode so that
you can listen to the motion sequence that you just
recorded.
After pressing the Stop/ Cancel key to stop playback, perform step numbers 2 and fol-
lowing for "Saving a pattern that you create" to save the pattern that contains the mo-
tion sequence you just recorded.
There are two types of motion sequence (Smooth
and Trig Hold
). During playback,
switch between these to hear the difference. (Refer to p.34 "Playing a motion sequence.")
After recording a motion sequence, you can edit it using the Pattern mode STEP
EDIT functions Motion Dest. and Motion Value. (See p.39 “Editing motion sequence
data”)
The number of valid knobs and keys for motion sequences are limited, depending on
the part. If you record more than the valid number of motion sequences for the same
part, the effect for the previous knob or key will be erased.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operation (Quick Start)
Playing with Pattern Set
What is Pattern Set?
Pattern Set is a function that lets you assign favorite patterns to the 16 step keys,
and switch between them as desired. While playing, you can successively select
favorite patterns, or play combinations of patterns as a loop (see p.40 "Chain
playing pattern sets").
When you hold down the Keyboard key (the key will blink) and
press one of the sixteen step keys, the pattern assigned to that key
will be selected. At this time you can use the Select keys to change
the pattern set group indicated by the red select LEDs (lower line) 1-
-4, to use 16 x 4 (total of 64) pattern sets.
If during playback you hold down the Keyboard key and press an-
other step key, the pattern assigned to that key will begin playing
when the currently-playing pattern finishes playing. (Refer to p.40
"Pattern Set.")
While the Keyboard key is blinking, it will control the Pattern Set
function.
If you hold down the Shift key and press the Keyboard key, the Pattern Set function will
be held. (The Keyboard key will blink.)
To defeat this "hold" condition, press the Keyboard key once again.
You can assign new pattern sets. (Refer to p.41, "Assigning a pattern to a Pattern Set.")
Pattern sets cannot be used in Song mode.
If you switch patterns during playback, the change will occur when each pattern
finishes playing. (Refer to p.25 "The timing at which patterns will change.")
Using the EM-1 as a tone generator module
Read this section when you wish to use the EM-1 with other connected MIDI equip-
ment. Use a MIDI cable to connect the MIDI OUT connector of your MIDI keyboard etc.
to theMIDIIN connector ofthe EM-1
.
1.Press the Global mode key to enter Global mode.
2.Use the cursor [L][L] keys to select MIDI ch (the corresponding
LED will light).
3.Press the part key for synth part 1 of the EM-1, and then turn the
dial to select the same channel as the connected MIDI keyboard
(or other device) (see p.47 “Setting the MIDI channel of each part
(MIDI ch)”).
4.When you play the connected MIDI keyboard (or other device),
you will hear the sound of synth part 1.
If you have connected a multi-track MIDI sequencer, set the MIDI
channel of synth parts 1 and 2, and the drum part (see p.47 “Setting
the MIDI channel of each part (MIDI ch)”). Set each part to the MIDI
channel of the track that you want it to play, and start your external
sequencer to play the parts.
For details on the EM-1's MIDI functionality, refer to p.49 "About MIDI."
If you wish to save Global mode settings, you must perform the Write operation (Re-
fer to p.48 “Saving your changes in Global mode (WRITE)”).
23
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Basic operation (Quick Start)
Synchronizing the playback with other ELECTRIBE models
For an even broader range of possibilities, the playback of the EM-1 can be synchro-
nized with other modelsoftheseries:theELECTRIBE• S
(ES-1 ), R (ER-1 ), and A(EA-
1 ). Here's how you can make the ES-1 playback in synchronization with the tempo of
theEM-1 .
Use a MIDI cable to connect the MIDI OUT connector of the EM-1 to the MIDI IN
connector of the ES-1 . Connect the part output jacks of the EM-1 and the line output
jacks of the ES-1 to your mixer or powered monitor
system (amplified speakers).
1.Press the Global mode key to move to Global
mode.
2.Use the cursor [L][L] keys to select Clock (the
corresponding LED will light).
E M -1
3.Set the EM-1 to "int," and the ES-1 to "E t." (Re-
fer to p.46 "Synchronizing the EM-1 with exter-
nal MIDI devices (MIDI Clock).")
4.Press the Play/ Pause key of the EM-1 to start a
pattern or song. (The Play/ Pause key will light.)
The ES-1 will play the pattern in synchronization
with the tempo of the EM-1
E S -1
.
If you want the EM-1 and ES-1 to play the identi-
cally-numbered pattern in synchronization, make
the following settings.
• SynchronizingtheES-1 tothe EM-1 asmaster.(Set
the EM-1 to "int," and the ES-1 to "E t.")
• Set the EM-1 and ES-1 to the same MIDI channel
(for example, set both to "01").
E S -1
E M -1
• On theEM-1 and ES-1 , set the MIDI filter setting
"P" to "O" (refer to p.47 "MIDI filter settings").
• On the ES-1 , set the MIDI note number set t in g
toC-1 .A-1
orA#8 .G9
.(ThiswillpreventtheES-
1 from being sounded unintentionally when note-
on messages are received.
It is also easy to make the EM-1 playback in syn-
chronization by connecting it to a sequencer or syn-
thesizer that can transmit and receive MIDI Clock
messages.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
If you switch to a different pattern without writing the
pattern whose tempo you modified, the pattern tempo
will return to the previous value. If you wish to keep the
modified tempo, you must perform the Write operation
(refer to p.41 "Saving a pattern (WRITE)").
4. Pattern mode
In this mode you can play patterns, edit patterns, or create
new patterns. To edit individual steps of a pattern, use the
Pattern mode Step Edit function. Press the PATTERN mode
key to enter Pattern mode. Although you can also enter Pat-
tern mode by pressing the STEP EDIT key, you should press
the PATTERN mode key if you wish to edit the Pattern, Tempo,
and Wave parameters.
Playing a pattern
(Pattern Play)
Press the Play/ Pause key to start pattern playback. When the
pattern finishes playing, it will return to the beginning and
continue playing.
To check the pattern that is playing, make sure that the PAT-
TERN mode key is lit, and use the cursor keys to select Pat-
tern (the corresponding LED will light).
You can use the keyboard function to play on the step keys
along with the pattern, press the drum part keys, or operate
the knobs and keys to modify the sound.
By taking advantage of the various functions of Pattern mode
as part of your performance technique, you can enjoy even
wider possibilities.
The timing at which patterns will
change
When you switch patterns during playback, the change will
occur when the currently playing pattern finishes its last step.
Until the pattern actually changes, the pattern number selected
in the display will blink.
Selecting a pattern
Pattern
A.01...d.64
Make sure that the Pattern mode key is lit.
Use the cursor keys to select Pattern (the corresponding LED
will light).
Rotate the dial to select one of the 256 patterns: A.01...A.64,
b.01...b.64, C.01...C.64, and d.01...d.64.
If you change patterns during playback, some slight
noise may be heard due to the change in delay time etc.
If the same effect is used with different settings in the
previous pattern and the newly-selected pattern, the
sound you hear will be the same as if those knobs were
turned.
Setting the playback tempo
Tempo
20.0...300.0
• Using the dial to change the tempo
Make sure that the Pattern mode key is lit.
Use the cursor keys to select Tempo (the corresponding LED
will light).
Playing from the beginning of a pat-
tern (Reset & Play)
If you hold down the Shift key when pressing the Play/ Pause
key, the playback will be forced to playback from the begin-
ning. By using this function in conjunction with setting the
tempo by the Tap key, you can synchronize the playback with-
out using MIDI.
If you wish to change the tempo units to the right of the deci-
mal place, hold down the Shift key and rotate the dial.
• Using the Tap Tempo key to
In order to ensure that the phrase always matches, you
will need to perform this adjustment each time.
change the tempo
While the pattern is playing, press the Tap key three times or
more at the desired tempo. The EM-1 will calculate the inter-
val at which you pressed the Tap key, and will change the
tempo accordingly. You can change the tempo in the same way
even when playback is stopped.
When you use the cursor keys to LEDs indicate select Tempo,
and the tempo you modified will appear in the display.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
About the tempo when you switch
patterns (Tempo Lock)
When the Tempo Lock key is off (key unlit), switching pat-
terns even during playback will cause the tempo to change to
the tempo of the newly selected pattern. If you want to keep
the same tempo, turn the Tempo Lock key on (key lit).
If the Tempo Lock key is on, the tempo will be held even
if you stop playback.To return to the tempo that is stored
for each pattern, turn the Tempo Lock key off (key dark),
and then re-select the pattern.
The state of the Tempo Lock key cannot be saved as
pattern data.
Selecting a part
Use the Part keys to select the part that you will edit or play
using the keyboard function.
The EM-1 has the following 12 parts.
When you hold down the Part Mute key (Tap key) to
select the Mute function, pressing a part key will not
sound that part.
• Eight drum parts to which you can assign a drum wave
• Two synth parts to which you can assign a synth wave
• Two accent parts that contain dynamics data for each step
The Part Solo function
By pressing the Solo key (the key will light) and pressing a
part key, you can hear only that part.
To solo two or more parts, hold down the Solo key and select
the desired parts. While the Solo key is lit, you can hold down
the Solo key (or Mute key) and press other part keys to add
more solo parts. If you press and then release the Solo key, the
Solo function will be canceled (the key will go dark).
Drum parts
When you press a drum part key, the accented sound will be
heard, and that part will be selected (the part key will light).
At this time, the step keys will light for the trigger locations in
the rhythm pattern of that part. During playback, the step that
is playing will also light simultaneously.
If you want to select a part during playback without caus-
ing the sound to be heard, hold down the Shift key and
press a drum part key.
When you press a drum part key to sound it, the sound
will be heard at the volume of when accent is on.
Solo more than one part
Synth parts
When you press a synth part key the key will light, and that
part will be selected. At this time, the step key indications will
depend on whether the Keyboard function is on or off.
Solo one part
On (lit):
During playback, keys of the corresponding pitch
will light consecutively at the timing at which the
selected part plays.
Off (dark): The phrase pattern trigger locations for the part
will light. During playback, the currently-playing
step will also light simultaneously.
Accent parts
When you press an accent part key, the key will light, and that
part will be selected. At this time, the step keys will light to
indicates the accent-on locations for that accent pattern. Dur-
ing playback, the currently-playing step will also light simul-
taneously.
The Part Mute function
By holding down the Part Mute key (Tap key) while you press
a part key, you can mute (temporarily silence) that part. While
you hold down the Part Mute key (Tap key), the mute status
of each part will be displayed. The part key of unmuted parts
will light, and muted part keys will be dark.
You can also mute two or more parts.
To cancel the mute setting, press the Solo key. To cancel mut-
ing for an individual part, press the key of that part.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
The parameters that are valid will depend on the type of part,
as listed below.
Creating a pattern
There are two ways to create a pattern. You can start with a
pattern that is similar to the desired result and then edit it, or
you can create a sound and rhythm-, phrase pattern for each
part from scratch. Either way, the EM-1 makes it easy for you
to create your own original patterns.
Drum part
EG Time, Pitch, Level Pan, Effect, Roll, Amp EG
Synth part
EG Time, Glide, Level, Pan, Effect, Roll, Amp EG,
Cutoff, Resonance, EG Int, Drive
If you wish to save a pattern you create, you must per-
form the Write operation before you select a different
pattern or turn off the power.
Accent part
Level
If the sound does not change when you rotate a knob or
switch the setting of a key, either another knob or key
has been set so that the parameter you are attempting
to adjust has no effect, or the Motion Sequence func-
tion (p.34 "Motion sequence") is operating.
Assigning a wave
Wave
(Drum parts)
(Synth parts)
off, 1...144
off, 1...50
Although drum parts 5A and 5B, and 6A and 6B can be
edited independently, they cannot be played simulta-
neously. If triggers for both exist at the same step, the
5B or 6B part will sound.
The EM-1 has 194 waves (144 for drum, 50 for synth) that you
can assign to each part.
A wave cannot be specified for an accent part. (The dis-
play will indicate “- - -.”)
Drum part
Make sure that the PATTERN mode key is lit.
Part common section
1. Use the cursor keys to select Wave (the corresponding LED
EG Time
0...127
will light).
This sets the time over which the EG will decay. The way
in which the volume decays will depend on the Amp EG
setting.
2. Press the key of the drum or synth part to which you wish
to assign a wave (the key will light). The number of the wave
assigned to that key will appear in the display.
Pitch
–64...63
3. For a drum part, turn the dial and press the part key to hear
the wave as you make your selection.
This specifies the playback pitch of the wave. Raising the
pitch will speed up the playback, and lowering it will slow
down the playback. The pitch can be adjusted over a range
of +/ –2 octaves, and will change in the following way.
4. For a synth part, turn on the keyboard function, turn the
dial, and press the step keys to hear the wave as you make
your selection.
Pitch Offset Values
If you do not wish to specify a wave, select “oFF.”
Value
Step
Value
Step
Value
Step
63 +12 (2 oct. up) 24 +3 1/2
-34 -5
61 +11 1/2
59 +11
57 +10 1/2
55 +10
53 +9 1/2
51 +9
49 +8 1/2
47 +8
45 +7 1/2
43 +7
41 +6 1/2
39 +6 (1 oct. up) -19 -2 1/2
36 +5 1/2
33 +5
21 +3
18 +2 1/2
15 +2
12 +1 1/2
09 +1
06 +1/2
00 actual pitch
-07 -1/2
-10 -1
-37 -5 1/2
-40 -6 (1 oct. down)
-42 -6 1/2
-44 -7
-46 -7 1/2
-48 -8
-50 -8 1/2
-52 -9
-54 -9 1/2
-56 -10
Chord splits
Several of the synth part waves sound as a chord. In some of
these, different chords are arranged across the keyboard within
the single wave. These are referred to as “chord splits.” Synth
part waves 43, 45, 46, and 47 are chord splits.
In some cases, the pitch may be discontinuous at the point
where chords change within a chord split. Be aware that if
you change the Transpose (p.35) or Song mode Note Ofs. (p.43)
settings, the chord or octave may be different from when you
created the pattern.
-13 -1 1/2
-16 -2
-58 -10 1/2
-60 -11
-62 -11 1/2
-64 -12 (2 oct. down)
-22 -3
-25 -3 1/2
-28 -4
30 +4 1/2
27 +4
-31 -4 1/2
Editing the sound of a part
Noise may occur when you raise the pitch.
Select the pattern whose sound you wish to edit. While strik-
ing the part keys or pressing the step keys (with the Keyboard
function turned on) to hear the sound, turn the knobs or switch
the keys to edit the sound. At this time, the Original Value
LED will light when the knob etc. that you are currently mov-
ing reaches the same value as the original sound of the pat-
tern.
Level
0...127
Adjusts the output level. Rotating the knob toward the
right will increase the level.
Pan
L64...r63
Adjusts the stereo position (panpot) of the sound. When
the knob is located at the center, the sound is panned to
the center. Rotating the knob toward the left will move
the sound toward the left, and rotating it toward the right
will move the sound toward the right.
You can also edit while playing back a pattern. It is also pos-
sible to use an external MIDI device to control the value of
each knob (refer to p.49 "About MIDI").
Amp EG
This switches the operation of the Amp EG. Pressing the
key will switch between an envelope that decays (
: key
lit) and an envelope that does not decay ( : key dark).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
Roll
Drive
0 ... 127
This turns the Roll (successive strike) effect on (lit) or off
This adjusts the degree of distortion for the sound of the
filter. By using this parameter in conjunction with the synth
filter Cutoff and Resonance to make the sound distort, you
can generate overtones that were not present in the origi-
nal waveform.
(dark) for each part. The roll interval is determined by the
tempo of the pattern and by the roll type (see p.32 “Set-
ting the roll type”). If you press and hold a part key when
Roll is on, roll playback will continue as long as you con-
tinue holding the part key.
Part Common section
Effect
This turns the effect on (lit) or off (dark) for each part.
EG Time
0...127
This has the same function as for a drum part (see p.27).
By setting EG Int in the negative direction, this can be used
as the attack time.
Motion Seq (motion sequence)
This records and plays back knob movements. Each time
you press this key, it will alternate between on (Smooth
lit), on (Trig Hold lit), and off (dark). (see p.34 “Playing
motion sequences”)
Glide
0...127
“Glide” (also called portamento) is a function that, when
the gate time length extends beyond the timing of the next
note, smoothly changes the pitch from the previous note
to the next note without re-triggering.
Synth part
Synth Filter section
The time from when the next note is played until that pitch
is reached can be specified as a multiple of steps (0, 1/ 4,
1/ 2, 1, 2, 4, 8, 16, 32, 64, 128 times) relative to the pattern
tempo. As this value increases, a longer time will be re-
quired before the target pitch is reached. Conversely if this
value is set to 0, the target pitch will be reached immedi-
ately, and since the note is not retriggered, this is suitable
when you wish to simulate a legato performance on a bass,
etc.
The filter processes the sound produced by the oscillator to
make it less bright, etc.
For some settings, slight noise may occur.
The Glide effect will be defeated when the Roll key
is on (lit).
Level
0...127
This has the same function as for a drum part (see p.27).
Pan
L64...r63
Cutoff
0...127
This has the same function as for a drum part (see p.27).
Set the cutoff frequency of the low-pass filter. Overtones
higher than the cutoff frequency will be cut, making the
sound more mellow.
Amp EG
This has the same function as for a drum part (see p.27).
Depending on the settings of this parameter, the
sound may be distorted or you may hear virtually no
sound.
Roll
This has the same function as for a drum part (see p.28).
When Roll is on, the sound will be played as a roll as long
as you hold down the step key (if the keyboard function is
on).
Resonance
0...127
This parameter adds character to the sound by boosting
the region around the cutoff frequency. If you raise the
resonance and turn the Cutoff knob (or adjust EG Int and
EG Time), you will hear the typical "meow-ing" sound
typical of analog synthesizers.
Effect
This has the same function as for a drum part (see p.28).
Motion Seq (motion sequence)
If the resonance is raised, the sound may be dis-
torted depending on the cutoff frequency or on the
pitch that you play.
This lets you record and play back knob movements of
the Part Common section and Synthesizer section. Each
time you press this, it will alternate between on (Smooth
lit), off (Trig Hold lit), and off (dark). (See p.34 “Playing a
motion sequence”)
EG Int (EG intensity)
–64...63
Specify the depth and direction of the effect that the EG
(envelope generator) will have on the cutoff frequency. The
EG will start when trigger-on occurs (the instant you play
the keyboard). If this knob is in the center position, the EG
will have no effect.
Accent parts
Part Common section
If the gate time length of a step extends beyond the
point at which the next step is sounded, the EG will
not be re-triggered for the next step.
Level
0...127
This adjusts the accent level (the amount of volume em-
phasis when accent is on). (See p.34 “Adding accents to
the pattern(Accent)”) Effect or delay edit.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
Ring Mod. (ring modulation)
This effect applies modulation to the sound in order to
Editing the effect or delay
create metallic resonances or unusual sound effects.
EFFECT
Edit 1 _ Frequency
0...127
On the EM-1, you can select and use one of eleven types of
effect for each pattern. The effect can be turned on/ off for each
part by using the Effect key in the Part Edit section. Use the
two knobs (Edit 1, Edit 2) to adjust the parameters, which will
differ depending on the selected effect.
Specifies the frequency of the modulation that will be ap-
plied. The frequency will rise as the knob is rotated to-
ward the right.
Edit 2 _ Balance
0...127
Specifies the balance of the effect sound and direct sound.
As the knob is rotated toward the right, the effect sound
will increase and the direct sound will decrease.
Although the effect can be turned on/off independently
for each part, the type and parameter values cannot be
changed independently.
Pitch Shifter
This effect shifts the pitch.
Some time may be required for the effect to begin ap-
plying when you switch patterns.
Edit 1 _ Pitch
0...127
Specifies the amount of pitch shift. When the knob is in
the center position, the output pitch will be the same as
the input pitch. As the knob is rotated toward the left the
pitch will become lower, and as the knob is rotated toward
the right the pitch will become higher. The available range
of pitch shift is +/ -2 octaves, and will change as shown
below.
Effect types and parameters
Motion Seq (motion sequence)
This is the motion sequence for the effect (see p.34 “Mo-
tion sequence”). Each time you press the key, this will al-
ternate between on (lit) and off (dark).
When Delay Editing is on, this will be the delay mo-
tion sequence key.
Pitch Offset Values
Value
Step
Value
Step
Value
Step
127 +12 (2 oct. up) 88 +3 1/2
30 -5
Reverb
125 +11 1/2
123 +11
121 +10 1/2
119 +10
117 +9 1/2
115 +9
113 +8 1/2
111 +8
109 +7 1/2
107 +7
105 +6 1/2
103 +6 (1 oct. up)
100 +5 1/2
97 +5
85 +3
82 +2 1/2
79 +2
76 +1 1/2
73 +1
70 +1/2
64 actual pitch
57 -1/2
54 -1
51 -1 1/2
48 -2
45 -2 1/2
42 -3
39 -3 1/2
36 -4
27 -5 1/2
24 -6 (1 oct. down)
22 -6 1/2
20 -7
18 -7 1/2
16 -8
14 -8 1/2
12 -9
10 -9 1/2
This simulates the reverberation and acoustics of a plate
reverb unit.
Edit 1 _ Time
0...127
The reverb time will lengthen as the knob is rotated to-
ward the right.
Edit 2 _ Level
0...127
8
6
4
2
0
-10
-10 1/2
-11
-11 1/2
-12 (2 oct. down)
The level of the reverberation will increase as the knob is
rotated toward the right.
94 +4 1/2
91 +4
Flg./Cho. (flanger/chorus)
33 -4 1/2
Flanger and chorus are effects that modulate the pitch of
a slightly time-delayed copy of the sound and add it to
the original sound to create a sense of spaciousness, modu-
lation, and vibrato.
Edit 2 _ Dry level
0...127
This adds the original sound to the pitch-shifted sound.
As the knob is rotated toward the right, increasing amounts
of the original sound will be added to the effect sound.
Edit 1 _ LFO Rate
0...127
Adjusts the LFO speed of the flanger/ chorus.
The LFO speed will become faster as the knob is rotated
toward the right.
Compressor
A compressor boosts low level sounds and reduces high
level sounds in order to minimize differences in volume
and make the sound more consistent.
Edit 2 _ Depth
0...127
Adjusts the depth of the flanger/ chorus effect. The effect
will change from chorus to flanger as the knob is rotated
toward the right.
Edit 1 _ Sensitivity
0...127
Specifies the sensitivity of the compressor. When the knob
is in the far left position, there will be no effect. As the
knob is rotated toward the right, the effect will apply more
strongly.
Raising the depth excessively may cause the sound
to distort.
Phaser
Edit 2 _ Attack
0...127
This effect adds modulation to the sound by mixing a cy-
Specifies the attack speed until the compressor begins to
take effect. The attack will become slower as the knob is
rotated toward the right.
clically phase-shifted sound with the original sound.
Edit 1 _ LFO Rate
0...127
Adjusts the LFO speed of the phaser. The LFO speed will
become faster as the knob is rotated toward the right.
Distortion
Edit 2 _ Depth
0...127
By boosting the volume appropriately, this effect causes the
Adjusts the depth of the phaser. The modulation will be-
come greater as the knob is rotated toward the right.
sound to distort and produces a rich overtone structure.
Edit 1 _ Gain
0...127
Specifies the degree of distortion. The sound will be dis-
torted more greatly as the knob is rotated toward the right.
Edit 2 _ Level
0...127
Adjusts the output level. The output level will increase as
the knob is rotated toward the right.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
Decimator
DELAY
This effect lowers the sampling frequency and the num-
ber of sampling bits, producing a grainy sound character-
istic of cheap samplers.
Delay is an effect that adds one or more delayed “echoes” to
the sound. The delay effect of the EM-1 is a “cross-feedback
delay.” This feeds the delayed L and R signal back into the
opposite side to produce a greater feeling of spaciousness from
left to right.
Edit 1 _ Sampling frequency
0...127
Rotating the knob toward the right produces a more lo-fi
sound, and rotating it toward the left produces a more hi-
fi sound.
This delay is a tempo delay in which the delay time is auto-
matically synchronized to the tempo of the pattern, and move-
ments of the delay knob can also be recorded as a motion se-
quence.
Edit 2 _ Number of sampling bits
0...127
Rotating the knob toward the right will produce a sound
typical of fewer bits (lo-fi), and rotating it toward the left
will produce a sound typical of more bits (hi-fi).
If the input volume is extremely low, there may be
no output. If there is a high noise level during silent
times, noise may be generated.
Resonator
This adds a specific frequency region to the original wave-
Press the delay edit key (the key will light) to enter Delay Edit.
Use the two knobs (Time, Depth) to edit.
form that has been boosted by a band pass filter.
Edit 1 _ Cutoff frequency
0...127
The delay effect will apply to the entire pattern, and it is
not possible to change the effect independently for each
part.
This adjusts the cutoff frequency of the band pass filter.
The cutoff frequency will rise as you turn the knob toward
the right.
Edit 2 _ Resonance
0...127
To edit the delay, you must make sure that the Delay
Edit key is lit. If you move the effect type knob, you will
return to effect edit.
This boosts the sound in the region of the cutoff frequency,
adding a distinctive character to the sound. The resonance
will increase as you turn the knob toward the right.
Slight noise may be heard when you change patterns,
due to the change in delay time.
Depending on the cutoff frequency or input sound,
high resonance settings may cause the sound to
distort.
Motion Seq (motion sequence)
This is the delay motion sequence (see p.34 “Motion se-
quence”). Each time you press the key, the setting will al-
ternate between on (lit) and off (dark).
Filter
This is a low pass filter with resonance. It cuts the over-
tones that are above the cutoff frequency, producing a
milder tone.
Edit 1 _ Cutoff Frequency
0...127
Time (delay time)
0...127
Adjusts the cutoff frequency of the low pass filter. The cut-
off frequency will rise as the knob is rotated toward the
right.
Set the delay time in synchronization with the tempo. Rela-
tive to the step, you can set this in the range of 1/ 1500...1/
4, 1/ 3, 1/ 2, 2/ 3, 3/ 4, 1, 1.5, 2, 2.5, 3, 4, 5, 6, 7, or 8 times.
Turning the knob toward the left will shorten the delay
time, producing a doubling effect (a sound similar to mul-
tiple instruments playing together).
Edit 2 _ Resonance
0...127
This emphasizes the sound in the region of the cutoff fre-
quency, adding a distinctive character to the sound.
If the MIDI Clock setting is Ext (external), you can syn-
chronize the delay time to the clock of an external device.
(Refer to p.46 “Synchronizing the EM-1 and an external
MIDI devices (MIDI Clock)”)
Depending on the cutoff frequency or input sound,
high resonance settings may cause the sound to
distort.
Mod. Delay (modulation delay)
If the Time value is lowered excessively, the sound
may distort (clip).
This is a delay with an added chorus effect produced by
using an LFO to sweep the delay time. It produces an ef-
fect in which the sound is spread to left and right. This
delay is a tempo delay in which the delay time is auto-
matically synchronized to the tempo of the pattern.
If you change the delay time during playback, the
pitch of the delayed sound will change.
If the tempo settings cause the delay time to ex-
ceed 1.5 seconds, the delay time will automatically
be halved to stay within 1.5 seconds.
Edit 1 _ Time
0...127
This sets the delay time. The available settings are mul-
tiples of tempo-synchronized steps: 1/ 4, 1/ 3, 1/ 2, 2/ 3, 3/
4, 1, 4/ 3, 1.5, 2, 2.5, 3, 4, 5, 6, 7, and 8 times.
Depth
0...127
Adjusts the level of the delay sound and the amount of
If the MIDI Clock setting is Ext (external), you can syn-
chronize the delay time to the clock of an external device.
(Refer to p.46 “Synchronizing the EM-1 and an external
MIDI devices ( MIDI Clock)”)
feedback (the number of delay repeats).
Rotating the knob toward the right will increase the level
of the delay sound, and will also increase the amount of
feedback.
Edit 2 _ Depth
0...127
The further left or right the Pan of each part is set, the
more the sound will be spread to left and right.
This adjusts the LFO depth and the feedback amount of
the delay. Turning the knob toward the right will deepen
the LFO and increase the amount of feedback.
Raising the Depth excessively may cause the sound
to distort (clip).
30
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
Setting the Length
Length, Scale/Beat settings
1, 2, 3, 4
You can set the length (the length of the entire pattern) and
the basic beat (time signature).
1. If a pattern is playing, press the Stop/ Cancel key to stop
playback.
The Length and Scale/ Beat you specify here will affect the cor-
respondence between step keys and note values, and the maxi-
mum number of steps as shown in the following diagram.
If Scale/ Beat is set to “tri” (ꢀ3 x 12) or “tr2” (ꢁ3 x 12), step keys
13—16 will have no effect.
While the Shift key is held down, the upper line of select LEDs
(green) will indicate the length of the current pattern, and the
lower line of select LEDs (red) will indicate the beat.
2. Use the dial to select the pattern whose length you wish to
set.
3. Hold down the Shift key and press step key 1 (Length). (Key
1 will blink.)
4. The value will blink in the display. Use the dial to specify
the length.
Maximum number of steps
5. Press step key 1 once again to finalize the value. (Key 1 will
go dark.)
16
32
or
16
16
or
tri
12
12
Length
tr2
If you wish to cancel without changing the setting, press the
Stop/ Cancel key.
Select LED
1 (green) lit
Select LEDs
1, 2 (green) lit
Setting the Scale/Beat
16, 32, tri, tr2
Select LEDs
1 to 3 (green) lit
1. If a pattern is playing, press the Stop/ Cancel key to stop
playback.
Select LEDs
1 to 4 (green) lit
2. Use the dial to select the pattern whose scale/ beat you wish
to set.
3. Hold down the Shift key and press step key 2 (Scale/Beat).
(Key 2 will blink.)
4. The value will blink in the display. Use the dial to specify
the scale/ beat.
5. Press step key 2 once again to finalize the value. (Key 2 will
go dark.)
If you wish to cancel without changing the setting, press the
Stop/ Cancel key.
It is not possible to view or change the Length or Beat/
Scale during playback or recording, or during Pattern
Set Play.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
Swing settings
Creating a Pattern
The patterns of the EM-1 consist of a rhythm pattern created
by the drum parts, and a phrase pattern created by the synth
parts.
50...75
By adjusting the Swing settings you can offset the note timing
of the steps. For example, you can change a straight 16-beat
by adding a slight "bounce" or shuffle. The Swing value can
be adjusted from 50 to 75 (%), and will affect the note timing
of even-numbered steps. A setting of 50 will produce a perfect
16-beat, and a setting of 66 will produce a shuffle.
The rhythm pattern consists of a sequence pattern (note tim-
ing data) for each step of each part.
The phrase pattern consists of trigger (note timing data), note
number (pitch), and gate time (note length) data for each step
of each part.
As listed below, there are two ways to create a rhythm pattern
and three ways to create a phrase pattern.
1. If a pattern is playing back, press the Stop/ Cancel key to
stop playback.
• Realtime recording
2. Rotate the dial to select the pattern for which you wish to
make Swing settings.
Use the rhythm part keys and step keys (keyboard func-
tion: on) to record the rhythm or phrase by playing it just as
you want it to sound.
3. Hold down the Shift key, and press step key 3 (Swing). Key
3 will light.
• Step recording
4. A value will blink in the display. Rotate the dial to set the
Swing value.
With pattern playback stopped, use the step keys to create a
sequence pattern, or input pitch and note length for indi-
vidual notes at each step to create the pattern.
5. Once again press step key 3 to execute the Swing setting
(key 3 will go dark).
• Note edit (only for a phrase pattern)
Create a phrase by editing the data (trigger, note number,
gate time) of the selected step.
If you decide to cancel without making the setting, press the
Stop/ Cancel key.
If you wish to erase the rhythm and phrase data of each part
before you create a pattern, refer to p.38 “Erasing pattern data
from a part.”
The Swing setting has no effect if Length or Scale/Beat
is set to “tri” (ꢀ3 x 12) or “tr2” (ꢁ3 x 12).
It is not possible to view or adjust the Swing parameter
during playback or recording, or during Pattern Set Play.
Realtime recording
Please refer to "Realtime recording " (p.19) in chapter 3. Basic
operation (Quick Start).
Setting the Roll Type
2, 3, 4
Step recording
If you specify the Roll Type, the part steps for which Roll is
“on” will be subdivided. You can select a subdivision of ei-
ther 2, 3, or 4.
Please refer to "Step recording " (p.20) in chapter 3. Basic op-
eration (Quick Start).
1. If a pattern is playing, press the Stop/ Cancel key to stop
playback.
Note editing
A phrase pattern consists of the following three data items for
each step. For each step, you can set these three items.
2. Use the dial to select the pattern whose roll type you wish
to set.
• Trigger: Whether or not a note will sound
• Note number: The pitch that will be sounded
• Gate time: The duration of the sound
3. Hold down the Shift key and press step key 4 (Roll Type).
(Key 4 will blink.)
4. The value will blink in the display. Use the dial to specify
the number of subdivisions for the roll type.
5. Press step key 4 once again to finalize the value. (Key 4 will
go dark.)
If you wish to cancel without changing the setting, press the
Stop/ Cancel key.
It is not possible to change the Roll Type during play-
back, recording, or sampling, nor during Pattern Set Play.
It is not possible to apply a roll to note-on messages
from an external MIDI device.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
Selecting the step (Target Step)
Changing the note number (pitch)
Step Rec
1.01...4.16
Note.No
C1...G9
When the Pattern mode STEP EDIT key is on (key lit) and the
parameter select LEDs indicate Step Rec, the value shown in
the display is called the “target step.” The value in the display
indicates the location of the step within the phrase pattern. If
the keyboard function is off, the step key for the target step
will blink.
1. Press the STEP EDIT key.
2. Use the cursor keys to select Note No. (the corresponding
LED will light).
3. Press the key of the synth part that you wish to edit (the key
will light).
When the Keyboard key is on, the step keys will not
indicate the target step.
4. Turn off the keyboard function (the keyboard key will go
dark).
5. The step keys will light to indicate the trigger locations of
the pattern for that part. Press the step key for the step whose
note number you wish to edit (the key will blink). By press-
ing a step key where a trigger exists, you can audition its
pitch.
6. Rotate the dial to modify the note number of that step.
When the display is showing the Note. No, pressing a step
key will not switch its trigger on/ off. Changing the note num-
ber of a step whose trigger is off will have no effect.
If you turn that trigger on, the specified pitch will be used. To
transpose an individual part, refer to Shift Note in p.36 “Mov-
ing data within a part (Move Data).” To transpose the entire
pattern, refer to p.35 “Transposing a pattern (Transpose).”
To change the target step, you can use the dial or press one of
the sixteen step keys. Alternatively, you can hold down the
Shift key and use the Select keys to move forward or back-
ward in single steps.
The pitch will be shown in the display as follows.
In the case of a pattern with a length of 2 measures or greater,
you can use the Select keys to move the select LED in the lower
line (red) in order to change the length that is shown by the
step keys, and verify or modify the trigger locations.
Changing the gate time
Gate Time
0.25...64.0
1. Press the STEP EDIT key.
2. Use the cursor keys to select Gate Time (the corresponding
LED will light).
The maximum number of steps will depend on the length
and scale/beat settings.
3. Press the key of the synth part that you wish to edit (the key
will light).
4. Turn off the keyboard function (the keyboard key will go
dark).
Changing the trigger settings
Make sure that the PATTERN mode key is lit.
5. The step keys will light to indicate the trigger locations of
the pattern for that part. Press the step key for the step whose
gate time you wish to edit (the key will blink). By pressing a
step key where a trigger exists, you can audition its pitch.
1. Turn off the Keyboard key (the key will be dark).
2. Use the Synth part key to select the part that you wish to
edit.
6. Rotate the dial to modify the gate time of that step.
3. For a pattern with a pattern length of 2 measures or more,
you can use the Select keys to move the red select LEDs to
left or right to change the length location that you will edit.
The value shown in the display is the gate time length in units
of a step. For example if the gate time is set to 1.0, the gate
time will be exactly as long as one step.
4. The step keys will light to indicate the trigger locations of
the pattern for that part. You can press each key to switch
the trigger on/ off for that step. Each time you press a step
key, the trigger will alternate on (lit) and off (dark).
If the gate time length extends into the timing of the next
note, the filter EG of the next note will not be retriggered.
When the display is showing the Gate Time, pressing a step
key will not switch its trigger on/ off.
Changing the gate time of a step whose trigger is off will have
no effect. If you turn that trigger on, the specified gate time
will be used.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
Adding accents to the pattern
(Accent)
Accents (volume emphasis) can be added individually to the
drum part and synth part. When the accent is on, notes at the
same location (step) of each part will be emphasized.
Motion sequence
There are three types of motion sequence: part, effect, and de-
lay. The knobs and keys that are valid for each part, for effect,
and for delay are listed below.
Drum part
one from EG Time, Pitch, Level, and Pan
one from Effect, Roll, and Amp EG
total 2: one knob and one key
1. When you press the part key for the desired accent, the step
keys will indicate the accent pattern.
Synth part total 3: two knobs and one key
2. Each time you press a step key it will alternate on/ off, al-
lowing you to specify the desired accent pattern. You can
playback the pattern to hear the results as you create the
accent part.
one from EG Time, Glide, Level, and Pan
one from Cutoff, Resonance, EG Int, and Drive
one from Effect, Roll, and Amp EG
Accent part
Level
3. The amount of the accent is adjusted by the Level knob in
the part common section. Rotating the knob toward the right
will increase the difference between on and off. If the knob
is rotated all the way toward the left, there will be no effect.
Play back the pattern to hear the results as you make this
setting.
Effect
Edit1, Edit2
Valid only for the part whose Effect key is on.
Delay
Time, Depth
Applies to the entire pattern. The delay cannot be ap-
plied to an individual part.
Pressing the Accent part key by itself will not produce
sound. Also, if a part key is struck to play the sound, it
will be sounded with Accent on (i.e., the emphasized
sound). If you wish to hear the results of Accent, you
need to play back the pattern.
Playing a motion sequence
A motion sequence can be played back in one of the following
two ways, and you can select the playback method indepen-
dently for each part.
For effect and delay motion sequences, the motion sequence
of the part will be only Smooth. The motion sequence of the
accent part will be only Trig Hold.
Amp EG, Roll, and Effect will be played as Trig Hold
even if Smooth is selected as the type.
Smooth:
Knob values will be connected smoothly, and the sound will
change smoothly.
Trig Hold (trigger hold):
The value of the motion sequence knob will be held at the
note timing of that part.
There will be no effect when the Motion Sequence LED
is dark (off).
34
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
Recording a motion sequence
Knob and key movements (motion sequences) for each part,
effect, and delay can be recorded.
To record a motion sequence for a part, select the part, and
then turn on the Motion Sequence key of the Part Common
section.
Convenient functions for
editing patterns
If you wish to save the pattern you edit using these func-
tions, you must perform the Write operation before se-
lecting a different pattern or turning off the power.
When you newly record a motion sequence for a part,
the motion sequence for the previous knob or key will
be erased.
Transposing a phrase (Transpose)
Transpose
This transposes the phrase of synth parts 1 and 2.
1. While you continue pressing the Transpose key, the display
will indicate the current transposition status.
–24...24
To record an effect motion sequence, turn on the Motion Se-
quence key of the Effect/ Delay section (turn the Delay Edit
key off).
To enable the effect motion sequence, turn the effect on
(lit) for each part to which you want the effect to apply.
2. While holding down the Transpose key, rotate the dial to
transpose the phrase in semitone steps. +/–1 transposes the
pitch by a semitone, +/–2 by a whole tone, +/–7 by a fifth,
and +/–12 by one octave.
To record a delay motion sequence, turn on both the Delay
Edit key and the Motion Sequence key of the Effect/ Delay sec-
tion.
While holding down the Transpose key you can also use the
step keys or Select keys to transpose.
The delay motion sequence will apply to the entire pat-
tern. It cannot be set for individual parts.
When you hold down the Transpose key and use the step keys
to specify the transposition, step key 4 will correspond to the
C pitch.
For the recording procedure, refer to p.22 "Using a motion se-
quence" in section 3. Basic operation (Quick Start).
Checking motion sequence data
If motion sequence data has been recorded, you can hold down
the Shift key and press the Motion Sequence key to view the
status in the step keys.
•
•
•
If motion sequence data for the knobs of the Part Common
section is included
Step keys 1 and 2 will light
If motion sequence data for the knobs of the Synth Filter
section is included
To transpose an individual part, use the Shift note op-
eration described below.
Step key 3 will light
If motion sequence data for the knobs of the Part Common
section is included
If solo has been specified, the key will remain lit when
you specify a transposition, and will not change to blink-
ing. When you defeat the solo setting, the key will begin
blinking.
Step key 4 will light
•
•
•
•
If effect motion sequence (Edit 1 data) is included
Step keys 5 and 6 will light
The Transpose value is not saved. The next time that
the power is turned on, the value will be 0.
If effect motion sequence (Edit 2 data) is included
Step keys 7 and 8 will light
If a chord split (see p.27) is selected as the wave for the
synth part, the chord or octave may change when you
specify a transposition.
If delay motion sequence (delay time data) is included
Step keys 9 and 10 will light
If delay motion sequence (delay depth data) is included
Step keys 11 and 12 will light
It is not possible to check motion sequence data during
playback, or recording, nor during Pattern Set Play.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
Moving data within a part
(Move Data)
By executing the Move Data operation you can move the loca-
tion of the pattern and motion sequence data for the selected
part (Shift Data), or transpose the notes of the entire part (Shift
Note).
Shift Data
–16...16
Use this when you want to change the starting location of a
pattern.
1. If the pattern is playing, press the Stop/ Cancel key to stop
playback.
2. Hold down the Shift key and press step key 5 (Move Data).
(Key 5 will blink.)
3. All part keys and the effect/ delay motion sequence key will
blink. If you do not want to shift the data of a specific part
or of the motion sequence, press that key to make it go dark.
You will be able to audition the sound each time you press a
part key.
Shift Note
–24...24
This function simultaneously shifts the note data of all steps
in the selected synth part.
1. If the pattern is playing, press the Stop/ Cancel key to stop
playback.
4. A number will blink in the display. Rotate the dial to select
the number of steps and the direction (positive or negative)
in which the data will be moved.
2. Hold down the Shift key and press step key 5 (Move Data).
(Key 5 will blink.)
5. Press the blinking step key 5 to execute the Move Data op-
eration.
3. Turn on the Transpose key (the LED will blink).
4. Synth part keys 1 and 2 will blink. If you do not want to
shift the data of a specific part, press that key to make it go
dark. (The part will sound at C4.)
To cancel without executing, press the Stop/ Cancel key.
The Shift Data operation applied to all steps of the selected
part. Data that is moved beyond the last step of the pattern
will "wrap around" to the first step. For example if 64-step
data is moved for "5" steps, the data that was in steps 60
through 64 will be moved to steps 1 through 5. Likewise, data
that is moved earlier than the first step of the pattern will "wrap
around"to the last step. For example if 48-step data is moved
for "–3 " steps, the data that was in steps 1 through 3 will be
moved to steps 46 through 48.
5. A number will blink in the display. Rotate the dial to select
the amount of pitch shift. +/–1 transposes the pitch by a
semitone, +/–2 by a whole tone, +/–7 by a fifth, and +/–12 by
one octave.
6. Press the blinking step key 5 to execute the Move Data op-
eration.
To cancel without executing, press the Stop/ Cancel key.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
Data Copy within a pattern
Copying a part (Copy Part)
Phrase pattern data (including motion sequence data) that you
create for a pattern of length 1 can be copied to the steps of
lengths 2...4. This function is a convenient way to create a pat-
tern that uses similar phrases repeatedly.
You can copy the sound settings and pattern data (including
motion sequence) from a selected part to another part.
1. If the pattern is playing, press the Stop/ Cancel key to stop
playback.
1. Create a pattern with a length of 1, and Write it into memory.
(Refer to p.41 "Saving a pattern.")
2. Press the Part key to select the copy destination part (the
LED will light).
2. At this point, the same data as in length 1 will automatically
be copied to the steps of lengths 2...4.
3. Hold down the Shift key and press step key 6 (Copy Part).
(Key 6 will blink.) The display will begin blinking.
3. Change the pattern length to the desired length. (Refer to
p.31, "Length, Scale/ Beat settings.")
4. Rotate the dial to select the copy source pattern number.
5. Press a part key to select the copy source part. (The copy
source key will blink, and the copy destination key will be
dark.) At this time, you will be able to audition the sound
each time you press the copy source part key. (Synth parts
will sound at C4.)
4. The steps of lengths 2...4 will contain the same data as length
1. Now you can edit the data of lengths 2...4 to complete the
pattern.
The data will be copied in a similar way when the pattern
length is 2 or 3 (refer to the table below). If you shorten a pat-
tern you create, the data will be copied according to the short-
ened length.
6. Press step key 6 once again to execute the Copy Part opera-
tion.
To cancel, press the Stop/ Cancel key.
When copying between a synth part and a drum part,
only the trigger data will be copied.
For details on data copy within the same part, refer to
the following section "Data Copy within a part."
A.01
C.20
The data that is copied automatically when you Write a
pattern does not force the pattern length (1...4) to change.
If the length is 4, data will not be copied within the pat-
tern.
Copying the sound of a part
(Copy Sound)
d.01
You can copy the sound of another part to the selected part.
(Step data and motion sequence data will not be included.)
1. If the pattern is playing, press the Stop/ Cancel key to stop
playback.
2. Press a part key to select the copy destination part. (The key
will light.)
3. Hold down the Shift key and press step key 7 (Copy Sound)
(key 7 will light). The display will begin blinking.
4. Use the dial to select the copy source pattern number.
5. Press a part key to select the copy source part. (The copy
source key will blink, and the copy destination key will be
dark.) At this time, you can audition the sound by pressing
the copy source key. (Synth parts will sound at C4.)
6. Press step key 7 once again to execute the Copy Sound op-
eration.
To cancel, press the Stop/ Cancel key.
It is not possible to copy sounds between a synth part
and a drum part.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
Erasing pattern data from a part
To erase the pattern data for the selected part, you can use
one of the following two methods in addition to turning each
of the sixteen step keys off.
Erasing motion sequence data
from the part, effect, or delay
(Clear Motion)
This operation simultaneously erases the part, effect, or delay
motion sequence data.
Erasing data during playback or recording
(Erase)
1. If the pattern is playing, press the Stop/ Cancel key to stop
playback.
1. Press the Part key to select the part from which you wish to
erase data.
2. Hold down the Shift key and press step key 8 (Clear Mo-
2. During playback or recording, hold down the Shift key and
press the Rec key. As long as you continue holding these
keys, trigger data will be automatically be erased from the
selected part.
tion). (Key 8 will blink.)
3. Press the key of the part (drum, synth, accent) whose mo-
tion sequence you wish to erase, or the motion sequence
key of the effect/ delay section (you may select more than
one). The selected key(s) will blink.
If you execute Erase on a synth part, only the trigger
data will be erased, and the note number and gate time
data of each step will remain.
4. Press step key 8 once again to clear the motion sequence
data.
To cancel, press the Stop/ Cancel key.
The entire motion sequence of the selected part, effect,
or delay will be erased at once. (If you select delay, both
time and depth data will be erased.)
Erasing all data from a part (Clear Part)
This operation simultaneous erases a rhythm or phrase pat-
tern (trigger, note number, gate time) and motion sequence
data.
1. If the pattern is playing, press the Stop/ Cancel key to stop
playback.
2. Press the Part key to select the part whose data you wish to
erase.
3. Hold down the Shift key and press step key 9 (Clear Part).
(Key 9 will blink.)
4. Once again press step key 9 to clear the data.
To cancel without clearing the data, press the Stop/ Cancel key.
When you execute Clear Part for a synth part, all steps
of the phrase pattern will be set to a pitch of “C4” and a
gate time of “1.00”.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
Exchanging data between parts
(Swap Part)
All data of the selected part can be exchanged with a part of
same pattern.
Editing motion sequence
data
You can edit the motion sequence of each part or the effect
and delay motion sequence. The data can be edited in units of
individual steps.
1. If the pattern is playing, press the Stop/ Cancel key to stop
playback.
Selecting a motion sequence
2. Press a part key to select the parts that you wish to swap
(the key will light).
Motion Dest. EGt(EG Time)...tin(Time)
1. Select the pattern that contains the motion sequence data
3. Hold down the Shift key and press step key 10 (Swap Part)
(key 10 will blink).
4. If you selected a synth part in step 2, both keys will blink
automatically. If you selected a drum part in step 2, select
the other drum part that you wish to swap (both of the two
keys being swapped will blink). At this time, you can audi-
tion the sound by pressing the respective part key. (Synth
parts will sound at C4.)
you wish to edit.
2. Press the STEP EDIT key (the key will light).
3. Use the cursor keys [L][L] to select Motion Dest (the cor-
responding LED will light).
4. By turning the dial you can select parameters from the mo-
tion sequence which is currently recorded for that part.
5. Press step key 10 once again to execute the Swap Part op-
eration.
To cancel the operation, press the Stop/ Cancel key.
It is not possible to swap between a synth part and a
drum part.
Example
A.01
If you wish to select a parameter for which no motion sequence
is recorded for the part, hold down the Shift key while you
turn the dial.
For motion sequences which have been recorded using
the EGTime, Pitch/Glide, Level, Pan, Cutoff, Resonance,
EG Int, and Drive parameters, their values will be initial-
ized to “diS” when you hold down the Shift key and se-
lect a parameter for which no motion sequence is re-
corded.
A.01
The parameters and valid number of parameters for each part
are given below.
Only one of the following parameters is valid for each part:
EGt (EG Time), PCh/GLd (Pitch/ Glide), LEU (Level), PAn
(Pan).
Only one of the following parameters is valid for each synth
part: Cut (Cutoff), rES (Resonance), EGi (EG Int), drU (Drive).
Only one of the following parameters is valid for each part:
AnP (Amp EG), roL (Roll), EFF (Effect).
Ed1 (Edit 1) and Ed2 (Edit 2) are valid for parts for which the
effect is turned on.
tin (Time) and dPt (Depth) are valid for the pattern (all parts).
39
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
While editing a motion sequence, it is not possible to
use the step keys to switch steps on/off.
Editing the parameter values of a
motion sequence
Depending on the part, some parameters cannot be
selected.
Motion Value
*Only synth part
While editing a motion sequence, the Rec key has no
effect.
EGt (EG time)
dis, –64...63
dis, –64...63
dis, 0...127
dis, L.64...r.63
dis, 0...127
dis, 0...127
dis, 0...127
dis, 0...127
dis, oFF...on
dis, oFF...on
dis, oFF...on
dis, 0...127
dis, 0...127
dis, 0...127
dis, 0...127
PCh/GLd (Pitch/Glide*)
LEU (Level)
If you modify the motion sequence values for Edit1, Edit2,
Time, and Depth in a single part, the change will apply
to all parts.
Pan (Pan)
Cut (Cutoff)
rES (Resonance*)
EGi (EG Int*)
AnP (EG Int*)
EFF (Effect)
roL (Roll)
Pattern Set
Pattern Set is a function that lets you assign favorite patterns
to the 16 step keys, and switch between them as desired. While
playing, you can successively select favorite patterns, or play
combinations of patterns as a loop.
rEU (Reverse)
Ed1 (Edit 1)
By using the Select key in conjunction with this to switch pat-
tern set groups, you can register and select 16 x 4 (total of 64)
patterns.
Ed2 (Edit 2)
Tin (Time)
dPt (Depth)
Using Pattern Set to perform
(Pattern Set Play)
1. Press the STEP EDIT key (the key will light).
2. Use the cursor keys [L][L] to select Motion Value (the cor-
responding LED will light).
Press the Play/ Pause key to begin playback.
3. The display will alternately show the parameter name you
selected in the preceding “Selecting a motion sequence,” and
the value of the parameter.
Hold down the Pattern Set key and press a step key to switch
to the pattern that was assigned to that step key.
By holding down the Pattern Set key and pressing a Select
key, you can switch to a different group of assigned pattern
sets. The pattern set group will be indicated by the lower line
of the Select LEDs (red).
4. Press a part key to select the part that you wish to edit.
5. Press a step key to select the step that you wish to edit. The
steps of a pattern whose length is two measures or greater
can be selected successively by pressing the Select key.
By holding down the Shift key and pressing the Pattern Set
key, you can hold the Pattern Set function (the key will light).
To defeat the Hold condition, press the Pattern Set key once
again (the key will go dark).
6. Rotate the dial to edit the parameter value at that step. If
the display indicates “diS,” the motion sequence does not
apply to that step.
Tempo adjustment, and functions such as Reset & Play etc.
are the same as for Pattern Play.
Pattern Set cannot be used during recording.When you
enter recording (ready) mode, Pattern Set will be can-
celled.
When the Pattern Set key is blinking, it will operate as
the Pattern Set function.
Chain Play of pattern sets
This function lets you select the starting and ending pattern
sets, and play them as a loop. While the Pattern Set function is
held, press the two step keys to which the patterns you wish
to play are assigned.
For example if patterns are assigned to the step keys as shown
in the table below, the operation described below will cause
playback to loop in the order of A.01, A.20, b.03, b.04, and A.51.
(A.01 is step key 1 of group 1, and A.51 is step key 5.)
When you select a parameter in Motion Dest for which
no motion sequence is recorded, and then change a
Motion Value, all Motion Values in same section will be
initialized to “diS.”
If you move to another pattern without writing the edited
motion sequence, it will revert to the state of the original
motion sequence. If you wish to keep the edited motion
sequence, you must perform the Write operation (see
p.41 “Saving a pattern (WRITE)”).
40
Download from Www.Somanuals.com. All Manuals Search And Download.
4.Pattern mode
1. Press the group 1 (select LED1 is lit) step key 1.
Assigning a pattern to a Pattern Set
1. With playback stopped, press and hold the Pattern Set key
and press the step key for the location that you wish to as-
sign a pattern.
2. Continue holding down step key 1, and press step key 5.
The indicators from step key 1 through step key 5 (chosen for
chain play) will light.
2. While continuing to press the Pattern Set key (or while Hold
is still in effect), rotate the dial to select the pattern number
that you wish to assign. Release the Pattern Set key (or de-
feat Hold) to complete the assignment process.
3. To save the pattern set assignments, press the Stop/ Cancel
key to stop playback. Continue pressing the Pattern Set key,
and press the Write key (the Write key will blink).
4. The display will blink "PSt." Press the Write key once again
to save the data.
You can also use the Select key to create chain play that ex-
tends across groups.
To cancel, press the Stop/ Cancel key.
If you want chain playback to occur in the order of A.20, b.43,
b.61, C.21, C.23, C.56, C.64, and C.28, perform the following
operation. (A.20 is step key 14 of group 1, and A.28 is step key
5 of group 2.)
If the Global mode Memory Protect setting is on, it will
not be possible to write the data. In this case, turn off
the Global mode Memory Protect setting before you ex-
ecute the Write operation.
1. Press group 1 (select LED 1 lit) step key 14.
Never turn the power off during the Write operation.This
may damage the data.
2. Continue holding down step key 14, and press the Select
key to select group 2 (select LED 2 lit). At this time, the se-
lection extends to group 2 step key 14.
If you release step key 14 at this point, the selection will
extend to group 2 step key 14.
3. Continue holding down step key 14, and press group 2 step
key 5.
The step keys selected for chain play will light from 1 through
5 when select LED 2 is lit, and from 14 through 16 when select
LED 1 is lit.
Saving a pattern (WRITE)
If you wish to keep the pattern data that you create, you must
perform this Write operation. When you perform the Write
operation, "Data Copy within a pattern" (p.37) will occur au-
tomatically, depending on the pattern length.
While chain play is playing, you can hold down the Shift key
and press the Play/ Stop key to play back from the beginning
of the currently-playing pattern.
If you intentionally want to discard your edits and revert to
the original pattern data, simply select a different pattern with-
out Writing.
To stop chain play, you can either select a different pattern set,
or defeat the pattern select Hold function.
1. If the pattern is playing, press the Stop/ Cancel key to stop
playback.
2. Press the Write key once (the key will blink). The pattern
number will blink in the display.
3. Rotate the dial to select the writing destination pattern num-
ber.
4. Press the Write key once again to write the data.
To cancel, press the Stop/ Cancel key.
If the Global mode Memory Protect setting is on, it will
not be possible to Write. In this case, you must turn off
the Global mode Memory Protect setting before you ex-
ecute the Write operation.
Never turn off the power during the Write operation.This
can damage the data.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
5.Song mode
You can use the dial or theTAP key to change the tempo
regardless of the on/off state of the Tempo Lock key.
5. Song mode
The on/off state of the Tempo Lock key can be saved as
part of each song. To save the modified tempo, perform
the Write operation (see p.45 “Saving a song (WRITE)”).
A song consists of patterns arranged in the desired order of
playback.
You can create and save up to sixteen songs in the internal
memory of the EM-1. In addition to pattern playback, songs
can also record overdubbed phrases and knob movements.
Press the Song mode key to enter Song mode.
Playing a song (Song Play)
Press the Play/ Pause key to begin playing the song. The song
will begin playing from the pattern of the currently selected
position. When the song ends, playback will automatically
stop.
It is not possible to save edited sounds in a song. Please
use Pattern mode to edit sounds.
What is Position?
"Position" refers to the playback or recording order of the pat-
terns within the song, and is the unit by which you edit a song.
Selecting a song
Song
S.01...S.16
Use the cursor keys to select Song (the corresponding LED
will light)
Rotate the dial to select one of the sixteen songs S.01 to S.16.
Fast-forward or rewind a song
During song playback, you can use the select keys to fast-for-
ward or rewind. To fast-forward, press the [ ] select key. To
rewind, press the [ ] select key.
Setting the playback tempo
Tempo
20.0...300.0
• Using the dial to set the tempo
Use the cursor keys to select Tempo (the corresponding LED
will light). Rotate the dial to set the tempo.
If you wish to change the tempo units to the right of the deci-
mal place, hold down the Shift key and rotate the dial.
• Using the tap tempo key to set the
tempo
Switching songs
While the song is playing, strike the Tap key three times or
more in succession at the desired tempo. The EM-1 will calcu-
late the interval at which the Tap key was pressed, and will
set the tempo accordingly. The tempo can be set in the same
way even when playback is stopped.
It is not possible to switch songs during playback, but it is
possible to select the song number beforehand. If you select a
song number during playback, the display will blink to indi-
cate the selected number. When the currently playing song
ends, playback will stop, and the newly selected number will
now be steadily lit. Press the Play/ Pause key to playback the
selected song.
When you use the cursor keys to make the parameter select
LEDs indicate Tempo, the current tempo will appear in the
display.
If you modify the tempo of a song but then switch to
another song without Writing, the first song will return to
its original tempo. If you wish to keep the tempo setting
you modified, you must perform the Write operation (re-
fer to p.45 "Saving a song (WRITE)").
Playing from the beginning of a
position or song (Reset & Play)
While a song is playing, you can hold down the Shift key and
press the Play/ Pause key to start playback from the begin-
ning of the pattern specified for the currently-playing posi-
tion. In addition, you can press the Play/ Pause key while a
song is playing to pause the playback, and then hold down
the Shift key and press the Play/ Pause key to playback from
the beginning of the song.
• Using the Tempo Lock key to fix
the song tempo
If the Tempo Lock key is turned on (lit), the playback will main-
tain the current tempo even when the song moves to the pat-
tern at the next position.
If the Tempo Lock key is turned off (dark), the tempo will
change to the tempo of the pattern at that position when the
song moves to the next position.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
5.Song mode
To play back the completed song from the beginning, press
the Play/ Pause key once, and then press the Stop/ Cancel key.
Alternatively, use the cursor keys to select Position, and ro-
tate the dial or use the select keys to set the position to "001."
Then press the Play/ Pause key. If you wish to view the order
of patterns in the song, or to re-select the pattern for a specific
position, use the cursor keys to select Pattern. Each time you
press a select key, you will move to the next or previous posi-
tion. You can use the dial to change the pattern number that is
displayed.
Creating a song
Creating a song from scratch
Here's how to create a song by placing patterns in the desired
order.
If you switch to a different song while editing a song,
your edited data will be lost. If you wish to keep the ed-
ited song, you must perform the Write operation to save
the song data.
Erasing song data (Clear Song)
1. If a song is playing, press the Stop/ Cancel key to stop play-
back. Then select the song that you wish to erase.
Alternatively, you can use the cursor keys to select Position,
and use the dial or select key to select the position you wish to
check. Then use the cursor keys to select Pattern, and view or
change the pattern.
2. Hold down the Shift key and press step key 13 (Clear Song).
(Key 13 will blink.)
3. Press step key 13 once again to erase the song data.
To cancel, press the Stop/ Cancel key.
If you erase the song data by mistake, rotate the dial to re-
select the song before you save it. This will restore the data to
its original condition.
Specifying the Note of each pattern
Note Ofs.
–24...24
This function offsets the Note of the pattern at the specified
position within the song.
Note Ofs. simply offsets the pitch within the song. It does
not affect the pitch data of the pattern itself.
1. If the song is playing, press the Stop/ Cancel key to stop
playback.
2. Use the cursor keys to select Position (the corresponding
LED will light).
Specifying a pattern for each position
3. Use the dial or Select keys to select the position whose pitch
you wish to offset.
Position
Pattern
001...256
4. Use the cursor keys to make the parameter select LEDs in-
A.01...d.64
dicate Note Ofs..
Specify a pattern for each position. When doing this, please
turn the Keyboard function key off (the key will go dark).
5. Use the dial to specify the desired pitch offset. +/–1 offsets
the pitch by a semitone, +/–2 by a whole tone, +/–7 by a
fifth, and +/–12 by one octave.
1. Use the cursor keys to make the parameter select LEDs in-
dicate Position. Notice that the display indicates "001."
Even when the parameter select LEDs indicate Note Ofs., you
can use the Select keys to move the position forward or back-
ward in single steps.
2. Use the cursor keys to make the parameter select LEDs in-
dicate Pattern.
If a chord split wave (see p.27) is selected for the part,
changing the Note Offset may change the chord or oc-
tave.
3. Rotate the dial to select the pattern that you wish to assign
to position "001."
4. Press the select [ ] key to advance to the next position. The
display will indicate "End."
5. Rotate the dial to select the pattern. The pattern you select
here will be the pattern for position "002."
6. When you select a pattern for the "End" position, the "End"
will move to the next position. Repeat steps 4 and 5 to as-
sign as many patterns as you wish.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
5.Song mode
Deleting a pattern from a specified po-
sition (Delete Pattern)
Editing a song
You can insert a new pattern into a song, or delete an existing
pattern. You can also add knob movements or your own per-
formance to a song.
You can delete a pattern from a specified position, and subse-
quent patterns will be moved forward (toward the beginning
of the song).
If you wish to keep the edited song, you must perform
the Write operation. If you select a different song or turn
off the power without performing the Write operation,
the song will return to the state in which it was before
you edited it.
Inserting a pattern at a specified posi-
tion (Insert Pattern)
You can insert a pattern at a specified position, and subsequent
patterns will be moved backward (toward the end of the song).
1. If the song is playing, press the Stop/ Cancel key to stop
playback.
2. Hold down the Shift key and press step key 12 (Delete Pat-
tern). (The 12 key will blink.)
3. The position indication in the display will blink. Rotate the
dial to select the position from which you wish to delete the
pattern. (For example if you wish to delete the pattern from
position 5. make the display blink "005.")
4. Press step key 12 once again, and the pattern will be deleted.
To cancel, press the Stop/ Cancel key.
1. If the song is playing, press the Stop/ Cancel key to stop
playback.
When you delete a pattern, the event data (refer to the follow-
ing page) at that position will also be deleted.
2. Hold down the Shift key and press step key 11 (Insert Pat-
Data following the inserted pattern will be moved forward.
tern). (The 11 key will blink.)
3. The position indication in the display will blink. Rotate the
dial to select the position at which you wish to insert a pat-
tern. (For example if you wish to insert a pattern into posi-
tion 3. make the display blink "003.")
4. Press step key 11 once again, and a pattern will be inserted
in front of that position. (The key will go dark.)
To cancel, press the Stop/ Cancel key.
The pattern that is inserted will be the pattern which had pre-
viously been at that position. Now you can specify the de-
sired pattern for the position that was inserted.
Data following the inserted pattern will be moved backward.
Changing the pattern for a specific position
1. If you are playing back, press the Stop/ Cancel key to stop
playback.
2. Use the cursor keys to select Position (the corresponding
LED will light).
3. Use the dial to select the position that you wish to modify.
4. Use the cursor keys to make the parameter select LEDs in-
dicate Pattern.
5. Use the dial to select the pattern that you wish to assign to
the selected position.
If you wish to audition the patterns as you select one,
press the Pattern mode key to enter Pattern mode, and
listen to the playback. To return to Song mode, press
the Stop/Cancel key to stop playback, and then press
the Song mode key.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
5.Song mode
After rewinding a song, it may not be possible to play-
back exactly according to the event data.
Recording knob movements or your
performance in a song
If during playback you operate a knob that had been
event-recorded, playback of the events of that knob will
be cancelled until it reaches the next position.
(Event Recording)
In Song mode you can create a performance not only by com-
bining patterns, but also recording a realtime performance that
you play on the drum part keys and step keys (using the key-
board function), and by turning the knobs.
Deleting event data from a song
To delete event data from a song, you can perform event re-
cording over the area that you wish to delete (without operat-
ing any knobs or keys).
Recording such a performance in Song mode is referred to as
“event recording.”
The following four types of performance data (event data) can
be recorded by event recording.
Checking for song event data
• Performances using the drum part keys
• Performances using the keyboard function
• Knob and key operations (only for the selected part)
• Tempo
If event data is recorded in a song, step keys 13 through 16
will light if you hold down the Shift key and press the Motion
Sequence key of the Part Common section.
It is not possible to check for event data during playback
or recording.
Event recording allows you to record two or more types of
events in the same area, as long as the events are played at the
same time.
Event recording always rewrites the previous data ("replace
recording"), and when you record your performance, any event
recording data previously in that area will be erased. (It is not
possible to layer event recording over the same area.)
Saving a song (WRITE)
If you wish to save a song that you create, you must perform
this Write operation.
If you decide not to save the song data you create, simply
switch songs without performing the Write operation.
1. Select the song on which you wish to record events.
2. Use the cursor keys to select Position (the corresponding
1. If the song is playing, press the Stop/ Cancel key to stop
playback. Use the cursor keys to select Song (the correspond-
ing LED will light).
LED will light).
3. Use the dial or the Select keys to move to the position at
which you wish to begin recording.
2. Press the Write key once (the key will blink). The song num-
ber will blink in the display.
4. Press the Rec key, and then press the Play/ Pause key to be-
gin event recording.
3. Rotate the dial to select the desired destination song num-
ber.
5. Use the part keys and/ or the knobs to perform.
6. Press the Stop/ Cancel key to stop event recording.
4. Press the Write key once again to save the data. (The key
will light, and then go dark.)
If the musical data of the song coincides with the event-re-
corded data, the event data will be given priority during play-
back.
To cancel, press the Stop/ Cancel key.
If the Global mode Memory Protect setting is on, it will
not be possible to write the data. In this case, turn off
the Global mode Memory Protect setting before you ex-
ecute the Write operation.
Never turn the power off during the Write operation.This
may damage the data.
Knob movements that are event-recorded in Song mode will
always playback in a way that corresponds to the Smooth type
motion sequence setting (and not the Trig Hold type).
If you wish to save the event recording, you must per-
form the Write operation. If you switch songs or turn off
the power without performing the Write operation, the
data that was recorded will be lost.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
6.Global mode
Synchronizing the EM-1 to a mas-
ter external MIDI device (Ext)
1. Use a MIDI cable to connect the MIDI IN connector of the
EM-1 to the MIDI OUT connector of the external MIDI de-
vice (sequencer or synthesizer etc.).
6. Global mode
In Global mode you can set parameters such as Metronome or
Protect. Press the Global mode key to enter Global mode.
To exit Global mode, press a different mode key.
The settings you make in Global mode will be cancelled
if you turn off the power without Writing. If you wish to
save the settings you make, you must perform the Write
operation (refer to p.48 "Saving your changes in Global
mode").
2. Use the cursor keys to select Clock (the corresponding LED
will light).
3. Rotate the dial to select "E t" (external clock).
4. Make settings on the external MIDI device (master) so that
it will transmit MIDI Clock messages.
5. Return to Pattern mode or Song mode.
Metronome settings
6. When you start the sequencer of the external MIDI device,
Metronome
oFF, r-0, r-1, r-2, on
the EM-1 will simultaneously begin playback.
Specify how the metronome will function. If you will be using
realtime recording to create a pattern from scratch, it is conve-
nient to use the metronome. The metronome will sound at
quarter-note timing.
7. If MIDI Clock data is being received at the MIDI IN con-
nector, you can make the EM-1 playback in synchroniza-
tion with the external MIDI device by pressing the EM-1's
Play/ Pause key.
oFF: The metronome will not sound.
r-0: The metronome will sound only during recording
(when the Rec and Play/ Cancel keys are lit).
r-1: When recording, a one-measure count will be sounded
before recording begins. The metronome will sound only
during recording.
r-2: When recording, a two-measure count will be sounded
before recording begins. The metronome will sound only
during recording.
on: The metronome will sound during playback and record-
ing. There will be no count before recording begins.
1. Use the cursor keys to select Metronome (the correspond-
ing LED will light).
If the MIDI Clock parameter is set to "Ext" and the EM-1
is synchronized to the external MIDI clock, it will syn-
chronize to the tempo of the external sequencer, and it
will not be possible to change the tempo on the EM-1.
2. Rotate the dial to make the metronome setting.
3. Press the PATTERN, STEP EDIT, or SONG key to return to
the previous mode.
If a MIDI Start message is received while the EM-1 is
already playing in synchronization with MIDI Clock, the
EM-1 will begin playback from the beginning of the cur-
rently playing pattern (or in the case of a song, from the
beginning of the pattern that was playing when the Start
message was received).
The metronome setting cannot be written.When you turn
on the power, it will always be "oFF."
Synchronizing the EM-1
with external MIDI devices
(MIDI Clock)
Synchronizing an external MIDI de-
vice to the EM-1 as master (int)
1. Use a MIDI cable to connect the MIDI OUT connector of
the EM-1 to the MIDI IN connector of the external MIDI
device (sequencer or synthesizer etc.).
Clock
int, Ext
The Global mode Clock setting allows the tempo of the EM-1
to be synchronized with the tempo of an external MIDI device
that is able to send or receive MIDI Clock messages.
2. Use the cursor keys to select Clock (the corresponding LED
will light).
For details on synchronization settings of your external MIDI
device, refer to the owner's manual for your device.
3. Rotate the dial to select "Int" (internal clock).
Even if you set Clock to Ext, the EM-1 will operate with
its own internal clock if no MIDI Clock messages are
being received at its MIDI IN connector.
4. Make settings on the external MIDI device (slave) so that it
will receive MIDI Clock messages.
5. When you start playback on the EM-1, the external MIDI
device will begin playback in synchronization.
When you perform the Reset & Play operation to begin
playback from the beginning of the pattern, the EM-1
will transmit only a MIDI Start message.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
6.Global mode
The factory settings are as follows.
The correspondence between note names and note
numbers will differ by manufacturer. Please refer to the
owner’s manual for the device you have connected.
Setting the MIDI channel of
each part (MIDI ch)
MIDI filter settings
Here you can select the types of MIDI message that will be
transmitted and received.
For each character "PCE" in the display, select "O" if you want
that type of message to be transmitted and received, or select
"-" if you do not want that type of message to be transmitted
or received.
MIDI ch
1...16
You can set the MIDI channel of synth part 1, synth part 2, and
the drum part. The same MIDI channel will be used for trans-
mission and reception. The factory settings are listed below.
1. Use the cursor keys to select MIDI Filter (the correspond-
ing LED will light).
Part
Channel
2. Rotate the dial to select the combination of message types
that will be transmitted and received; "O" allows transmis-
sion and reception, and "-" disables it.
Synth part 1 (global)
Synth part 2
1
2
Drum part (1—6B)
10
P: Transmission/ reception of Program Change, Bank Se-
1. Use the cursor keys to select MIDI ch (the corresponding
lect, and Song Select messages.
LED will light).
C: Transmission/ reception of Control Change messages.
2. Press the part key for which you wish to change the MIDI
channel (the key will light). For the drum part, press any
one of the eight part keys (all of the drum part keys will
light).
E: Transmit/ receive exclusive data. However while you are
operating the Dump settings, this data will be transmit-
ted and received regardless of the setting here.
3. Turn the dial to select the channel.
Program changes and exclusive data will be transmit-
ted and received on the MIDI channel you specify here
for synth part 1 (i.e., this will be the global MIDI chan-
nel).
Setting the MIDI note number
of a drum part
Adjusting the pitch bend
range
Drums Note No.
C-1...G9
For each drum part, you can specify the MIDI note number as
a note name.
Bend Range
–12...12
If you specify the same note number for two or more parts,
the sounds of those parts will be played simultaneously when
that note is received from an external MIDI device.
You can adjust the range of the pitch bend that will occur when
MIDI Pitch Bend messages are received.
1. Hold down the Shift key and press step key 14 (Bend Range)
1. Use the cursor keys to select Drums Note No (the corre-
(key 14 will blink).
sponding LED will light).
2. Turn the dial to select the pitch range. +/-1 is a semitone, +/
2. Press the part key whose note number you wish to change
(the key will light).
-2 is a whole step, +/-7 is a fifth, and +/-12 is an octave.
3. Press step key 14 once again to finalize the pitch range (key
14 will go dark).
3. Rotate the dial to select the note number.
To cancel without making the setting, press the Stop/ Cancel
key.
For some sounds, the pitch may not rise all the way to
the specified range.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
6.Global mode
When the parameter select LEDs indicate Dump, sys-
tem exclusive data can be transmitted or received even
if the MIDI Filter parameter "E" is set to "-."
Transmit/receive dump data
Dump
Pt.A, Pt.b, Pt.C, Pt.d, SnG, ALL
When the EM-1 receives a data dump, it will take up to
ten seconds to write the data into memory (the Write
key will light). Never turn off the power of the EM-1 dur-
ing this time. Doing so may damage the data. Also, new
MIDI data cannot be received during this time. If you
want the EM-1 to receive multiple data dumps in suc-
cession, you must leave an interval between each of
the transmitted data dumps.
Transmission
Here's how system exclusive data (pattern data, song data, or
Global mode settings) can be transmitted from the EM-1 to an
external MIDI data filer or computer connected to the MIDI
OUT connector.
1. Connect the MIDI OUT connector of the EM-1 to the MIDI
IN connector of an external MIDI device that is able to re-
ceive MIDI data dumps (another EM-1, or a computer that
is running a MIDI data filer program or editing program,
etc.).
Memory Protect (Protect)
This is the protect setting for Pattern mode and Song mode.
When protect is “on,” the Write key will not function, and it
will not be possible to rewrite data or receive a MIDI data dump.
When you wish to save edited data or receive a data dump,
turn protect “oFF.”
2. Set the MIDI channel of the external MIDI device and the
EM-1 to match. However when transmitting to a data filer,
it is not normally necessary to match the MIDI channel.
3. Hold down the Shift key and press step key 15 (key 15 will
light).
1. Press the Stop/ Cancel key to stop playback.
2. Hold down the Shift key and press step key 16 (Protect).
4. Turn the dial to select the data that you wish to transmit.
(Key 16 will blink.)
Pt.A: pattern bank A data (A.01—A.64)
Pt.b: pattern bank b data (b.01—b.64)
Pt.C: pattern bank C data (C.01—C.64)
Pt.d: pattern bank d data (d.01—d.64)
SnG: all song data
3. Rotate the dial to change the blinking display to either “on”
or “oFF.”
4. Press step key 16 once again to finalize the protect on/ off
setting (key 16 will go dark).
GLb: global data
If you decide to cancel without changing the setting, press the
Stop/ Cancel key.
5. Press step key 15 once again to finalize the data that will be
transmitted. (The Play/ Pause key will blink.)
If you wish to save the protect setting, perform the Global mode
Write operation (described below).
6. Press the Play/ Pause key to transmit the data.
With the factory settings, this is turned on.
If you wish to cancel before transmitting the data dump, press
the Stop/ Cancel key.
This setting is valid in Pattern mode and Song mode. In
Global mode, it is always possible to execute Write re-
gardless of the Memory Protect setting.
Reception
Here's how EM-1 system exclusive data can be received from
an external MIDI data filer or computer connected to the MIDI
IN connector.
Saving your changes in Glo-
bal mode (WRITE)
When the Global mode Protect setting is "on," it is not
possible to receive MIDI dump data outside of Global
mode.
Here’s how you can save the changes you made in Global
mode.
1. Connect the MIDI IN connector of the EM-1 to the MIDI
OUT connector of the external MIDI device that will trans-
mit the MIDI data dump (another EM-1, or a computer that
is running a MIDI data filer program or editing program,
etc.).
If you wish to save the changes you made, you must perform
this Write operation. The settings will take effect whenever
the power is turned on. Conversely, if you do not want to save
the changes you made, simply turn off the power without
Writing.
1. Press the Stop/ Cancel key to stop playback.
2. Set the MIDI channel (Synth part 1) of the external MIDI
device and the EM-1 to match. However when transmitting
from a data filer, it is not normally necessary to match the
MIDI channel.
2. Press the Global mode key.
3. Press the Write key once (the key will blink). The display
will indicate “– – –.”
3. Hold down the Shift key and press step key 15 (key 15 will
light).
4. Press the Write key once again to complete the operation.
If you decide to cancel, press the Stop/ Cancel key.
4. Transmit the data dump from the external MIDI device.
In Global mode it is always possible to write, regardless of the
Memory Protect setting (preceding section).
Details on data dumps are provided in the MIDI implementa-
tion chart of the EM-1.
Consult your local Korg distributor for more information on
MIDI implementation
Never turn off the power while data is being written into
memory. Doing so may destroy the data.
Do not touch the keys of the EM-1 while a data dump is
in progress.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
7.Data
5. Using NRPN messages to edit
7. Appendices
NRPN (Non-Registered Parameter Number) is a category of
messages for which each manufacturer is free to assign a func-
tion to a parameter number and use it as desired. NRPN mes-
sages are assigned to each knob and key of the EM-1's
Effect/ Delay section (except for Delay Edit). To edit, first use
NRPN (LSB) [Bn, 62, rr] and NRPN (MSB) [Bn, 63, mm] (con-
trol change #98 and 99) (rr, mm: lower and upper bytes of the
parameter no.) to select the parameter. Then transmit Data
Entry (MSB) [Bn, 06, mm] and Data Entry (LSB) [Bn, 26, vv]
(control change #06 and 38) (mm, vv: upper and lower bytes
of the value, together expressing 16,384 steps) to set the value.
The EM-1 uses only the MSB value (128 steps) of the Data Entry
message.
About MIDI
1. MIDI channels
Similarly to a television, data can be received when the chan-
nel of the receiving device matches the channel on which the
data is being transmitted.
On the EM-1, the transmit/ receive channels for synth part 1,
synth part 2, and all drum parts are set by the MIDI ch pa-
rameter of Global mode.
2. Note-on/off
6. If "stuck notes" occur
When you strike a drum part key, the note number assigned
to that drum part key will be transmitted on the specified MIDI
channel. When you play the step keys using the keyboard func-
tion, a note-on message [9n, kk, vv] (n: channel, kk: note num-
ber, vv: velocity) will be transmitted on the MIDI channel speci-
fied for the part, with the note number assigned to each step
key, and a velocity corresponding to the force with which you
pressed the step key.
If for some reason a note fails to stop sounding, you can usu-
ally switch modes to stop the sound. If a note played via MIDI
fails to stop, you can simultaneously press the Shift key and
the Stop/ Cancel key to perform a MIDI Reset.
7. About synchronization
Two or more sequencers can be connected via MIDI and made to
playback in synchronization. Messages used for synchronization
(realtime messages) include Timing Clock [F8], Start [FA], Con-
tinue [FB], and Stop [FC]. In a synchronized system, one synthe-
sizer (the master) will transmit these messages, and the other
sequencer(s) (the slave(s)) will receive these messages. The slave
devices will playback according to the tempo specified by the
Timing Clock messages transmitted by the master. Twenty-four
Timing Clock messages are transmitted for each quarter note.
When the EM-1’s Global mode parameter Clock is set to INT, it
will be the master device, and will transmit these realtime mes-
sages. When Clock is set to EXT, it will be the slave device, and
will receive these realtime messages. However even when Clock
is set to EXT, the EM-1 will operate according to its own internal
clock if no Timing Clock messages are being received. The Start
message specifies when playback will begin. When the Start/
Pause key is pressed on the master device, it will transmit a Start
message. Slave devices that receive this Start message will syn-
chronize to the Timing Clock messages subsequently received,
and will begin playback from the beginning. If the Start/ Pause
key is pressed on the master devices when it is paused, the mas-
ter will transmit a Continue message. When a slave device re-
ceives the Continue message, it will resume playback from the
point where it is currently stopped. If the Stop key is pressed
during playback, the master will transmit a Stop message. Slave
devices will stop playback when they receive a Stop message.
On the EM-1, the vv: velocity value is determined by the Ac-
cent level. When you release a pad, a note-off message [8n, kk,
vv] is transmitted. However, most devices do not transmit
note-off velocity, and neither does the EM-1. When note-on/
off messages for a note number assigned to a part are received,
that part will sound.
3. Switching patterns
When you switch patterns, Program Change and Bank Select
messages [Bn, 00, mm] (control change #00), [Bn, 20, bb] (con-
trol change #32) (mm: bank number upper byte, bb: bank num-
ber lower byte, together allowing 16,384 banks to be selected)
will be transmitted.
If a Program Change is received on the MIDI channel of the
EM-1, patterns will be switched within the same group (e.g.,
from A.01 to b.64). After a Bank Select has been received, the
next-received Program Change will be able to switch to a pat-
tern of a different group (e.g., from A.01 to C.01).
Transmission and reception of Program Change messages can
be controlled by the Global mode MIDI Filter setting.
Bank Select
Program Change Pattern number
MSB LSB
00
00
00
01
0...127
0...127
A.01...b.64
C.01...d.64
4 Applying pitch bend
8. Synchronization in Song mode
The EM-1 does not transmit pitch bend messages [En, vv, vv]
(vv, vv: lower and upper places of the value, together express-
ing a range of 16384 steps where 8192 [vv, vv=00H, 40H] is the
center value). However when the EM-1 receives pitch bend
messages, a pitch bend effect will be applied to the synth parts.
The range of the pitch bend can be specified by editing the
Global mode Pitch Bend Range parameter.
In Song mode, the EM-1 can transmit and receive Song Select
and Song Position Pointer messages. When you switch songs,
a Song Select [F3 ss] message will be transmitted (ss: song num-
ber, where one of 128 songs can be selected. On the EM-1 you
can select 16 songs.) If the EM-1 receives a Song Select mes-
sage in Song mode, it will switch songs. Transmission and re-
ception of Song Select messages can be restricted by the MIDI
Filter settings of Global mode. If you change the current posi-
tion on the master device (i.e., the device whose Clock is set to
INT) when the song is stopped, a Song Position Pointer mes-
sage [F2 pp pp] will be transmitted. (pp: the number of MIDI
beats from the beginning of the song; i.e., the number of Tim-
ing Clocks divided by six.)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
7.Data
Song Position Pointer indicates the location at which the se-
Troubleshooting
quencer is currently stopped. When Song Position Pointer is
received in Song mode by a slave device (i.e., a device whose
Clock is set to EXT), it will change the location at which its
song is currently stopped to match the location of the master.
However on the EM-1, the length of each pattern may be dif-
ferent, so the master and slave will not necessarily be in the
same location. When the Start/ Pause key is pressed on the
master device, a Continue message is transmitted, and the song
will begin playback from the currently selected position. When
the slave device receives the Continue message, it will syn-
chronize to the Timing Clock messages and begin playback
from the current point in the song. In the same way as syn-
chronizing the playback from the beginning of the song, you
can specify the location at which playback will start, and then
playback in synchronization. If you use the dial or Select keys
to fast-forward or rewind while the song is playing, Song Po-
sition Pointer messages will not be transmitted. Be aware that
if you perform these operations during synchronized playback,
the synchronization will be lost. Also, even if Song Position
Pointer messages are received during playback, the playback
location will not change.
The display does not light up when I press the
Power switch!
• Is the AC adapter connected?
• Is the AC adapter plugged into an AC outlet?
No sound!
• Is your amp, mixer, or headphones connected to the correct
jack? (Can you playback a pattern? If so, the connections
are correct.)
• Are your amp or mixer powered-on and set correctly?
• Is the master volume knob of the EM-1 raised?
Sound does not stop!
• When a pattern is played back, it will continue playing re-
peatedly. When you are finished listening to a pattern, press
the Stop/ Cancel key (p.14).
Sounds or operations are different than when I
edited!
9. About system exclusive messages
Manufacturers are free to use system exclusive messages in
any way they choose, and these messages are used mainly to
transmit and receive parameters that are specific to particular
devices, such as sound data and editing data.
•
Did you perform the Write operation after editing? (p.41, 45)
After you have edited, you must perform the Write opera-
tion before switching songs or patterns, or turning off the
power.
The system exclusive message format of the EM-1 is [F0, 42,
3n, 61, ... F7] (n: exclusive channel).
• Did you edit the selected pattern or song after writing it?
However, some system exclusive messages have been defined
for use in a specific way, and these are called "universal sys-
tem exclusive messages."
Can't control via MIDI!
•
Is the MIDI cable connected correctly?
Of the various types of universal system exclusive message,
the EM-1 supports the following two.
When playing the EM-1 from an external device
•
When an Inquiry Message Request [F0, 7E, nn, 06, 01, F7] is
received, the EM-1 will transmit an Inquiry Message [F0,
7E, nn, 06, 02, (9 bytes), F7] that means “I am a Korg EM-1,
my system version is ...”
•
Has the EM-1 been set to receive MIDI data on the channel
on which the data is being transmitted? (p.47)
•
Is the Global mode MIDI Channel parameter set to the de-
sired channel? (p.47)
•
When a Master Volume [F0, 7F, nn, 04, 01, vv, vv, F7] mes-
sage is received, the volume of the entire system will change.
• Are the Global mode MIDI Filter settings set appropriately?
(p.47)
The exclusive channel is the same as the MIDI channel of synth
part 1
When playing an external device from the EM-1
• Does the MIDI channel of the EM-1 match the MIDI channel
10. Transmitting sound setting
data (Data Dump)
of the receiving device? (p.47)
Cannot write a pattern or song!
• Is the Global mode Protect setting turned "on"? (p.48)
Song, Pattern, or Global data can be transmitted as MIDI ex-
clusive data, and stored on an external device. This data is
transmitted by the Global mode Dump command. The chan-
nel used for transmission and reception of this data is set by
the Global mode MIDI ch setting. Data dumps are also trans-
mitted when a Data Dump Request message is received.
Playing the step keys does not sound the speci-
fied sound!
• After editing the sound of a part, did you perform the Write
operation? (p.41)
• Is the Keyboard function turned on?
11. Editing sounds etc.
• Is a motion sequence being used? (p.34)
By sending MIDI exclusive data dumps, you can rewrite all
patterns or individual programs. By using NRPN messages in
Pattern mode, you can edit the knobs that are active for each
part.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
7.Data
Error messages
Specifications
Number of parts:
Data could not be written.
Er.1
Er.2
12 parts
When writing a song to a song of a different
number, the maximum number of recordable
events was exceeded. Please erase event data
to free up memory (p.45).
Synth parts x 2
Drum parts x 8
Synth Accent part
Drum Accent part
Protect was turned "on" for the memory into
which you attempted to write data. In Global
mode, turn the Protect setting "oFF" (p.48).
Memory capacity:
256 patterns, 16 songs
Er.9
Full
Master effects: Tempo Delay,
Normal, Motion Sequence
When event-recording on a song, event data
memory has filled up. If you attempt to record
additional events, the "memory full" message
will appear immediately. Please erase event
data to free up memory (p.45).
Insert effects: 11 Type
Reverb, Flanger/ Choru s,Phaser, Ring
Modulator, Pitch Shifter, Compressor, Dis-
tortion, Decim ator, Resonator, Filter,
Modulation Delay
Restoring the factory set
data
Sequencer:
Pattern
Maximum 64 steps for each part,
Motion sequence,
Synth part: 3 parameters,
Drum part: 2 parameters,
Accent part: 1 parameter,
64 events
The pattern and song data with which the EM-1 is shipped
from the factory is referred to as the "preloaded data," and
you can restore this preloaded data back into the memory of
the EM-1.
Song
When you do this, the patterns you created and the songs
which use these patterns will be erased, and replaced by the
preloaded data. If you wish to keep the patterns and songs
you created, you must save the data on a data filer etc. before
you load the preloaded data.
Maximum 256 patterns per song
Maximum approximately 35,700 events
for event recording
Connectors:
PHONES
Stereo phone plug
1. While simultaneously pressing the Transpose key and the
Nominal level: 35 mW
Write key, turn on the power.
Load impedance: 33 ohms
OUTPUT (L/ MONO, R)
Phone jacks: mono x 2
2. The display will indicate "PLd," and the Play/ Pause key
will blink.
Nominal output level: -10 dBu
Output impedance: 1 k-ohms
MIDI (IN, OUT, THRU)
3. To load the factory preloaded data, press the blinking Play/
Pause key.
This will require apporoximately 30 seconds.
To cancel, press the Stop/ Cancel key.
Power supply: DC 9 V (AC adapter included)
Power consumption:
When loading is complete, the EM-1 will return to its initial
state. After several seconds the display will indicate pattern
number "A.01," and the EM-1 will be in Pattern mode.
5 W
Dimensions: 300 (W) x 222.5 (D) x 55.4 (H) mm
(with rubber feet)
Never turn off the power during the Load process. The
data may be damaged.
Weight:
1.25 kg
* Specifications and appearance are subject to change with out
notice for improvement.
C ancel
51
Download from Www.Somanuals.com. All Manuals Search And Download.
7.Data
Index
Distortion ------------------------- 29
Drive --------------------------10, 28
Drum part--------------------15, 26
Dump data------------------------ 48
L
A
Length ------------------------21, 31
Level ----------------------9, 27, 28
Accent ----------------------------- 34
Accent key------------------------ 10
Accent part ------------------15, 26
AMP EG--------------------------- 27
Amp EG ----------------------- 9, 28
Listen
Pattern ----------------------------- 14
Song ------------------------------- 13
E
Edit
Assign
M
Delay ------------------------- 17, 30
drum part ------------------------- 16
Effect ------------------------- 17, 29
Motion sequence data --------- 39
Note -------------------------------- 32
Part --------------------------------- 16
Phrase pattern ------------------- 18
Rhythm pattern ------------------ 18
Song ------------------------------- 44
Sound of a part ------------ 18, 27
Synth part ------------------------- 16
Pattern Set------------------------ 41
Wave ------------------------------- 27
MASTER VOLUME -------------- 8
Metronome ----------------------- 46
MIDI
B
Channel --------------------- 47, 49
Clock ------------------------------- 46
Connector ------------------------- 12
Filter -------------------------------- 47
Implementation Chart ---------- 55
LED ----------------------------------- 8
Note number --------------------- 47
Bank Select message --------- 49
Beat -------------------------------- 31
Beat LED --------------------------- 8
Bend Range---------------------- 47
C
Check
Effect--------------------------28, 29
Effect Edit------------------------- 17
Effect Key --------------------------- 9
Effect/Delay section -------------- 9
EG Intensity -----------------10, 28
EG Time------------------9, 27, 28
Erase -------------------------19, 38
Error message------------------- 51
Event Recording ---------------- 45
MIDI Implementation Chart -- 55
Mode
Motion sequence data --------- 35
Song event data ----------------- 45
Global ------------------------------ 46
Pattern ----------------------------- 25
Song ------------------------------- 42
Chord split ------------------------ 27
Clear
Mode key --------------------------- 8
Modulation Delay --------------- 30
Motion Dest. --------------------- 39
Motion Sequence --------------- 22
Motion sequence ---- 28, 30, 34
Motion sequence Key ----------- 9
Motion Value --------------------- 40
Move Data ------------------------ 36
Mute-------------------------------- 26
Motion ----------------------------- 38
Part --------------------------------- 38
Song ------------------------------- 43
Common section------------------ 8
Compressor ---------------------- 29
Connection ------------------------- 7
Connector section -------------- 12
F
Factory set data ----------------- 51
Fast-forward---------------------- 42
Filter-------------------------------- 30
Flanger/Chorus ----------------- 29
Copy
Data -------------------------------- 37
Part --------------------------------- 37
Sound ------------------------------ 37
N
Name
Cursor key -------------------------- 8
Cutoff -------------------------10, 28
G
Gate time ------------------------- 33
Glide --------------------------- 9, 28
Global mode --------------------- 46
Pattern ----------------------------- 54
Song ------------------------------- 54
Wave ------------------------------- 56
D
Data
Note editing ---------------------- 18
Note number ----------------33, 47
Note-on/off ----------------------- 49
NRPN------------------------------ 49
Copy-------------------------------- 37
Dump ------------------------------ 50
H
Headphone ----------------------- 12
Decimator------------------------- 30
Delay
I
Edit --------------------------------- 17
Edit Key ----------------------------- 9
Time -------------------------------- 30
O
Insert Pattern -------------------- 44
Offset Note ----------------------- 43
Original Value LED --------------- 9
K
Delete
Keyboard function -------------- 15
Keyboard Key-------------------- 11
Event data ------------------------ 45
Pattern ----------------------------- 44
Depth ------------------------------ 30
Diagram --------------------------- 13
52
Download from Www.Somanuals.com. All Manuals Search And Download.
7.Data
Song mode ----------------------- 42
Song Name List ----------------- 54
Song Play------------------------- 42
Specification --------------------- 51
Step key--------------------------- 11
Step Key section ---------------- 11
Step Recording ----------------- 20
Step recording--------------18, 32
Swap Part ------------------------ 39
Swing ------------------------------ 32
Synchronization ------ 24, 46, 49
Synth filter section-------------- 10
Synth part -------------------15, 26
System exclusive --------------- 50
Recording
P
Event ------------------------------- 45
Pan ------------------------9, 27, 28
Motion sequence ---------------- 35
Realtime ---------------- 18, 19, 32
Step --------------------- 18, 20, 32
Part--------------------------------- 15
Accent ----------------------- 15, 26
Clear ------------------------------- 38
Copy-------------------------------- 37
Drum ------------------------- 15, 26
Edit --------------------------------- 16
Swap ------------------------------- 39
Synth ------------------------- 15, 26
Reset & Play ----------------25, 42
Resonance ------------------10, 28
Resonator ------------------------ 30
Rest/Tie Key --------------------- 10
Reverb----------------------------- 29
Rewind ---------------------------- 42
Ring Modulation----------------- 29
Roll ------------------------9, 28, 32
Part common section ------------ 9
Part Mute ------------------------- 26
Part Mute Key ------------------- 10
Part Select section ------------- 10
Pattern
S
Change ---------------------------- 25
Creating --------------------- 27, 32
Delete ------------------------------ 44
Insert ------------------------------- 44
Listening -------------------------- 14
Name List ------------------------- 54
Play --------------------------------- 25
Reset & Play --------------------- 25
Selecting -------------------------- 25
Save
T
Global ------------------------------ 48
Pattern ----------------------- 21, 41
Song ------------------------------- 45
TAP--------------------------------- 10
Tap Tempo -------------------14, 25
Tap tempo ------------------------ 42
Target Step ----------------------- 33
Tempo ------------------ 14, 25, 42
Tempo Lock -----------------26, 42
Tempo Lock key ------------------- 8
Transmission --------------------- 48
Transpose ------------------------ 35
Transpose key ------------------- 10
Trigger hold ---------------------- 34
Trigger setting ------------------- 33
Troubleshooting ----------------- 50
Type ---------------------------------- 9
Scale------------------------------- 31
Section
Common ---------------------------- 8
Connector ------------------------- 12
Effect/Delay ------------------------ 9
Part common ----------------------- 9
Part Select ------------------------ 10
Sequence Control -------------- 10
Step Key -------------------------- 11
Synth filter ------------------------ 10
Pattern mode -------------------- 25
Pattern Name List -------------- 54
Pattern Set ----------------------- 23
Chain Play ------------------------ 40
Play --------------------------------- 40
Register --------------------------- 41
Select
Pattern Set key ------------------ 11
Phaser----------------------------- 29
Pitch-----------------------9, 27, 33
Pitch bend ------------------------ 47
pitch bend ------------------------ 49
Pitch Shifter ---------------------- 29
Part --------------------------------- 26
Select LED ----------------------- 11
Sequence Control section ---- 10
Shift Data ------------------------- 36
Shift key --------------------------- 11
Shift Note ------------------------- 36
Smooth ---------------------------- 34
Solo -------------------------------- 26
Solo key --------------------------- 10
W
Wave ------------------------------- 27
Wave Name List ---------------- 56
Play
Motion sequence---------------- 34
Pattern ----------------------------- 25
Pattern Set------------------ 23, 40
Song ------------------------------- 42
WRITE
Global ------------------------------ 48
Pattern ----------------------- 21, 41
Song ------------------------------- 45
Song ------------------------------- 13
Creating --------------------------- 43
Deleting event data ------------- 45
Editing ----------------------------- 44
Erasing ---------------------------- 43
Fast-forward ---------------------- 42
Listening -------------------------- 13
Name List ------------------------- 54
Reset & Play --------------------- 42
Rewind----------------------------- 42
Select ------------------------------ 42
Switching -------------------------- 42
Write ------------------------------- 45
Position---------------------------- 43
Power switch --------------------- 12
Program Change --------------- 49
Protect----------------------------- 48
WRITE key ------------------------- 8
R
Realtime recording -- 18, 19, 32
Reception------------------------- 48
53
Download from Www.Somanuals.com. All Manuals Search And Download.
7.Data
* Patterns and initial data for the demo song are assigned to bank d.
Pattern Name List
* The first pattern of each style is assigned to step keys 1...16 of the Pattern Set function.
b.51~C.09 : Drum’n’Bass
C.39~C.56 : Nu Skool Breaks/Big Beat
Style - A.01~A.32 : Best Selection
C.10~C.38 : R&B/Hip Hop/Trip Hop
C.57~C.64 : Other
A.33~b.50 : House/Techno
A Bank
No. Pattern Name
b Bank
No. Pattern Name
C Bank
No. Pattern Name
Tempo
Tempo
Tempo
A.01 Dream Trance 1
A.02 Epic Trance 1
A.03 Epic Trance 2
A.04 Epic Trance 3
A.05 Progressive Trance 1
140
133
141
144
139
b.01 2 Step/UK Garage 11
b.02 2 Step/UK Garage 12
b.03 2 Step/UK Garage 13
b.04 2 Step/UK Garage 14
b.05 House 3
135
138
133
135
124
C.01 Cyber/Tech Step 11
C.02 Cyber/Tech Step 12
C.03 Digital D’n’B 3
C.04 Artcore 1
170
165
190
175
164
C.05 Artcore 2
A.06 Psychedelic Trance 1
A.07 Psychedelic Trance 2
A.08 Breakstep
A.09 2 Step/UK Garage 1
A.10 2 Step/UK Garage 2
143
144
130
131
139
b.06 House 4
b.07 House 5
b.08 House 6
b.09 House 7
b.10 House 8
122
132
125
129
130
C.06 Artcore 3
C.07 Jump Up 1
C.08 Jump Up 2
C.09 Breaks
177
178
174
147
76
C.10 R&B 3
A.11 2 Step/UK Garage 3
A.12 House 1
A.13 House 2
A.14 NY Hard House 1
A.15 Minimal 1
132
114
128
134
138
b.11 House 9
124
124
132
136
139
C.11 R&B 4
C.12 R&B 5
C.13 R&B 6
C.14 R&B 7
C.15 R&B 8
109
90
96
77
96
b.12 Chicago House
b.13 NY Hard House 2
b.14 NY Hard House 3
b.15 Minimal 3
A.16 Minimal 2
A.17 Happy Hardcore 1
A.18 Gabba 1
A.19 Cyber/Tech Step 1
A.20 Cyber/Tech Step 2
138
168
185
177
176
b.16 Minimal 4
b.17 Minimal 5
b.18 Minimal 6
b.19 Minimal 7
b.20 Minimal 8
139
135
137
136
130
C.16 R&B 9
89
92
103
92
C.17 R&B 10
C.18 R&B 11
C.19 Hip Hop 4
C.20 Hip Hop 5
88
A.21 Cyber/Tech Step 3
A.22 Cyber/Tech Step 4
A.23 Digital D’n’B 1
A.24 Digital D’n’B 2
A.25 R&B 1
177
175
190
190
116
b.21 Minimal 9
b.22 Techno 1
b.23 Techno 2
b.24 Techno 3
b.25 Techno 4
132
134
130
128
140
C.21 Hip Hop 6
C.22 Hip Hop 7
C.23 Hip Hop 8
C.24 Hip Hop 9
C.25 Hip Hop 10
93
83
82
89
80
A.26 R&B 2
100
70
91
96
129
b.26 Techno 5
b.27 Techno 6
b.28 Techno 7
b.29 Electro 1
b.30 Electro 2
137
132
119
128
131
C.26 Hip Hop 11
C.27 Hip Hop 12
C.28 Hip Hop 13
C.29 Hip Hop 14
C.30 Hip Hop 15
91
113
86
91
96
A.27 Hip Hop 1
A.28 Hip Hop 2
A.29 Hip Hop 3
A.30 Nu Skool Breaks 1
A.31 Nu Skool Breaks 2
A.32 Big Beat 1
A.33 Epic Trance 4
A.34 Epic Trance 5
A.35 Epic Trance 6
127
128
140
141
143
b.31 Tek House 1
b.32 Tek House 2
b.33 Tek House 3
b.34 Tek House 4
b.35 Tek House 5
125
135
130
130
140
C.31 Trip Hop 1
C.32 Trip Hop 2
C.33 Trip Hop 3
C.34 Trip Hop 4
C.35 Trip Hop 5
75
87
90
81
82
A.36 Epic Trance 7
A.37 Epic Trance 8
A.38 Dream Trance 2
A.39 Dream Trance 3
A.40 Dream Trance 4
140
148
144
143
141
b.36 Tek House 6
b.37 Tek House 7
b.38 Progressive House 1
b.39 Progressive House 2
b.40 Progressive House 3
126
130
127
129
124
C.36 Trip Hop 6
C.37 Trip Hop 7
C.38 Trip Hop 8
C.39 Nu Skool Breaks 3
C.40 Nu Skool Breaks 4
88
95
90
133
132
A.41 Dream Trance 5
A.42 Dream Trance 6
A.43 Dream Trance 7
A.44 Dream Trance 8
A.45 Trance 1
145
140
140
140
134
b.41 Progressive House 4
b.42 Euro Hard House 1
b.43 Euro Hard House 2
b.44 Euro Hard House 3
b.45 Euro Hard House 4
129
140
136
135
142
C.41 Nu Skool Breaks 5
C.42 Nu Skool Breaks 6
C.43 Nu Skool Breaks 7
C.44 Nu Skool Breaks 8
C.45 Nu Skool Breaks 9
130
134
122
138
133
A.46 Trance 2
A.47 Trance 3
A.48 Progressive Trance 2
A.49 Progressive Trance 3
A.50 Progressive Trance 4
140
132
139
140
139
b.46 Euro Hard House 5
b.47 Hardcore 1
b.48 Hardcore 2
b.49 Happy Hardcore 2
b.50 Gabba 2
137
135
151
164
170
C.46 Nu Electro 1
C.47 Nu Electro 2
C.48 Nu Electro 3
C.49 Nu Electro 4
C.50 Nu Electro 5
122
129
130
135
120
A.51 Progressive Trance 5
A.52 Progressive Trance 6
A.53 Progressive Trance 7
A.54 Psychedelic Trance 3
A.55 Psychedelic Trance 4
138
140
139
146
148
b.51 Drum’n’Bass 1
b.52 Drum’n’Bass 2
b.53 Drum’n’Bass 3
b.54 Drum’n’Bass 4
b.55 Drum’n’Bass 5
172
172
172
173
175
C.51 Big Beat 2
C.52 Big Beat 3
C.53 Big Beat 4
C.54 Big Beat 5
138
129
141
140
130
C.55 Hardcore Breakbeat
A.56 Psychedelic Trance 5
A.57 Goa Trance
A.58 2 Step/UK Garage 4
A.59 2 Step/UK Garage 5
A.60 2 Step/UK Garage 6
140
145
129
130
132
b.56 Jazzstep 1
b.57 Jazzstep 2
b.58 Jazzstep 3
b.59 Cyber/Tech Step 5
b.60 Cyber/Tech Step 6
178
168
170
175
170
C.56 Industrial
C.57 Disco 1
C.58 Disco 2
C.59 Disco 3
C.60 Funk 1
81
110
107
120
90
A.61 2 Step/UK Garage 7
A.62 2 Step/UK Garage 8
A.63 2 Step/UK Garage 9
A.64 2 Step/UK Garage 10
132
132
130
137
b.61 Cyber/Tech Step 7
b.62 Cyber/Tech Step 8
b.63 Cyber/Tech Step 9
b.64 Cyber/Tech Step 10
170
170
170
175
C.61 Funk 2
91
132
128
90
C.62 Latin House 1
C.63 Latin House 2
C.64 Reggae
Song Name List
S.01: Drum’n’Bass Demo
S.03: Nu Skool Breaks Demo
S.05: R&B/Hip Hop Demo
S.02: Dream Trance Demo
S.04: 2 Step/UK Garage Demo
S.06...S.16: Blank
All Patterns and All Songs - ©2001 KORG Inc. All rights reserved.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
[Production station]
ELECTRIBE·M (EM-1)
MIDI Implementation Chart
2001.2.3
Transmitted
Recognized
Remarks
Function ...
Basic
Default
1 – 16
1 – 16
Memorized
channel
Changed
1 – 16
1 – 16
Default
Messages
Altered
3
×
Mode
×
* * * * * * * * * * * * * *
Note
0– 127
0– 127
number :
True voice
0– 127
* * * * * * * * * * * * * *
Velocity
Note ON
Note OFF
O 9n, v=30– 127
O 9n, v=1– 127
×
×
After
Touch
Polyphonic
Channel
×
×
×
×
Pitch Bender
×
O
*C
0,32
98, 99
8
O
O
O
×
O
O
O
O
Bank Select(MSB,LSB)
NRPN(LSB,MSB)
Data Entry(MSB)
*P
*C
*C
121
Reset All Controllers
Control Change
Program
Change :
O 0 – 127
O 0 – 127
0 – 127
Transmitted/ received in Pattern mode *P
Can always be transmitted/ received
True#
* * * * * * * * * * * * * *
System Exclusive
System Common
O
O
*2 *E
in the MIDI Dump page
: Song Pos
: Song Sel
: Tune
O
O 0 – 15
×
O
O 0 – 15
×
Transmitted/ received in Song mode
*1
*P
System Realtime : Clock
: Commands
O
O
O
O
*1
*1
Aux Messages
:
Local ON/ OFF
×
×
O
×
O
O
O
×
: All Notes OFF
: Active Sense
: Reset
Notes
*P, *C, *E: Sent and received when MIDI mode MIDI Filter (P, C, E) respectively
are set to "O"
*1: Sent but not received when Global mode Clock is "Int."When set to "Ext,"
received but not sent.
*2: In addition to Korg exclusive messages, also responds to Inquiry messages.
Mode 1: OMNI ON, POLY
Mode 3: OMNI OFF, POLY
Mode 2: OMNI ON, MONO
Mode 4: OMNI OFF, MONO
O : Yes
× : No
L Consult your local Korg distributor for more information on MIDI IMPLEMENTATION.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Wave Name List
Drum Wave Name
Drum Wave Name
Drum Wave Name
Synth Wave Name
No.
Name
No.
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Name
No.
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
Name
No.
Name
Clap-Hardhouse
Clap-R&B
HH-99 Cl
HH-99 Op
HH-88 Cl
Agogo
Triangle
1
2
3
4
5
6
7
8
BD-Dark
BD-99 1
BD-99 2
BD-Analog
BD-ZAP
BD-99 Dist 1
BD-99 Dist 2
BD-99 Dist 3
BD-Squash
BD-88 1
1
2
3
4
5
6
7
8
Saw-ProSynth
Boost Saw
Pulse 15%-MG
Pulse 25%-MG
Square
Triangle-MG
Sine
Sine Kick Bass
Dark Bass
Tambourine-Acc
Sleigh Bell
Cabasa-Normal
Cabasa-Dist Up
Cabasa-Dist Down
Shaker
HH-88 Op
HH-R&B Cl
HH-R&B Op
HH-Std 1 Cl
HH-Std 1 Op
HH-Std 2 Cl
HH-Std 2 Op
HH-Crisp Cl
HH-Crisp Op
HH-Old Cl
Guiro-Short
Guiro-Long
9
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Xmod Bass
Additive Sine
DWGS Bell
Samba Whistle
Tabla-Baya Ghe
Tabla-Baya Mute 1
Tabla-Baya Mute 2
Tabla-Na
BD-88 2
BD-Dry 1
BD-Dry 2
BD-Dry 3
BD-Dry 4
BD-Hip
DWGS FM Bass
HPF Saw-MS2k
SynthBass Oct
Square Oct Mix
Saw Oct Mix
DWGS Wire
DWGS Digital
5th Sine
HH-Old Op
Tabla-Tin
HH-Big Chunk Cl
HH-Big Chunk Op
Ride-99
Ride-Edge 1
Ride-Edge 2
Crash-99
Crash-Normal
Tom-99
Tom-88
Tabla-Mute 1
Tabla-Mute 2
Djembe-Open
Djembe-Mute
Djembe-Slap
Udu
Taiko-Open
Taiko-Rim
Tsuzumi
Zap-ER
BD-R&B
BD-Ambi
BD-Defness
BD-Defness/OHH
BD-Jungle
BD-Jungle/Crash
SD-99 1
SD-99 2
SD-88 1
SD-88 2
SD-Analog R&B
SD-77
SD-Disco
SD-Dry 1
SD-Dry 2
SD-Dry 3
SD-Dry 4
SD-Ambi 1
SD-Ambi 2
SD-Piccolo 1
SD-Piccolo 2
SD-Hip
SD-Brash Dist
SD-Crackle
SD-Jungle
SD-R&B 1
SD-R&B 2
SD-R&B 3
SD-R&B 4
SD-Rim 1
SD-Rim 2
SD-88 Rim
Clap-99
5th Square
5th Saw
5th Stab Saw
Detuned Saw-A26k
Unison Saw-MS2k
Sync Triangle-MS2k
Sync Saw-MS2k
HPF Sweep-MS2k
Cyber Bass-Z1
Ring Bass-MS2k
Vibrato Sine
Reso Noise
Tom-Std Hi
Tom-Std Lo
Zap-MG
Tom-Std Floor
Tom-Jazz Hi Rim
Tom-Jazz Hi
Tom-Jazz Floor
Bongo-Hi Op
Bongo-Slap
Bongo-Lo 1
Synth SE-MG
Synth SE-MS 1
Synth SE-MS 2
Filtered Perc
Synth Perc-ER 1
Synth Perc-ER 2
Synth Perc-MG 1
Synth Perc-MG 2
Synth Perc-MG 3
Filtered Noise
Reverse-BD
Reverse-SD 1
Reverse-SD 2
Reverse-Crash
Scratch-1
NRG Hit
Ac.Bass
Bongo-Lo 2
Finger Bass
Pick Bass-M1
Slap Bass Mix
Organ-M1
Combo Organ
DWGS Clav
Voice-VS
DWGS Voice
Synth Chord Set
Pad Chord
M1 Piano Chord Set
E.Piano Chord Set
Guitar Chord Set
Organ Chord
Vibe Chord
Conga-Hi Slap 1
Conga-Hi Slap 2
Conga-Hi MtSlap
Conga-Lo Slap 1
Conga-Lo Slap 2
Conga-Lo MtSlap
Timbales-Hi Rim
Timbales-Hi Edge
Timbales-Lo Rim
Timbales-Lo Open
Timbales-Paila
Claves
Scratch-2
Scratch-3
Cowbell
Cha Cha Bell
Mambo BellDrum
Clap-88
Noise
NOTICE
KORG products are manufactured under strict specifications and voltages required by each
country. These products are warranted by the KORG distributor only in each country. Any
KORG product not sold with a warranty card or carrying a serial number disqualifies the
product sold from the manufacturer’s/distributor’s warranty and liability. This requirement is
for your own protection and safety.
KORG INC.
15 - 12, Shimotakaido 1 - chome, Suginami-ku, Tokyo, Japan.
©2001 KORG INC.
1304 TH Printed in Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|