Function added in system version 2.0
E
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Function added in system version 2.0
If you want to use the joystick X-axis (left/right) as
a modulation source for another parameter, set the
following parameters to P.Bend according to the
parameter that you want to control.
When you operate the joystick in the –Y direction,
control change CC#02 will be transmitted on the MIDI
channel of the timbre you’ve selected. When CC#02 is
received, the result will be the same as when you
operate the joystick.
• Virtual patch P11 PATCH “Source” (RADIAS
owner’s manual p.91)
• Vocoder P07: FILTER “FcModSrc” (RADIAS
owner’s manual p.105)
• Effect control source (St.Filter “Ctrl Src,” etc.;
RADIAS owner’s manual p.125)
If you want to use the joystick –Y axis to apply an
effect, set the Program Edit mode P03–5: TIMBRE
CC-A tab page “Cntrl” parameter to “O” (Enable).
Make this setting for each timbre.
If you want MIDI control change messages to be
transmitted and received, set the Global mode P06:
MIDI FILTER page parameter “Ctrl Chg” to “O”
(Enable).
In these cases, the parameter will be controlled
with mm=64 and bb=00 as 0 (the center value), in a
range of -127 to +127 (received on the MIDI channel
of the timbre).
SW1/SW2
+Y axis
By setting one of the Global mode P04: MIDI page
parameters “MIDI1”–“MIDI5” to #080 (SW1) or #081
(SW2), you can use SW1 or SW2 as a source for the
following:
This will operate in the same way as the Modulation
wheel of the RADIAS-KB. Moving the joystick in the +Y
direction will apply a vibrato effect from LFO2
according to the “VibratInt” setting of the Program Edit
mode P05: PITCH page, and modulation depth (CC#01)
will be transmitted on the MIDI channel of the timbre
selected by TIMBRE SELECT. When CC#01 is received,
the result will be the same as when you operate the
joystick.
• Modulation source for a virtual patch (RADIAS
owner’s manual p.91)
• Modulation source for the vocoder filter (RADIAS
owner’s manual p.105)
• Effect control source (St.Filter “Ctrl Src,” etc.;
RADIAS owner’s manual p.125)
If you want to apply a vibrato effect by moving the
joystick in the +Y direction, set the Program Edit
mode P03–5: TIMBRE CC-A tab page “Cntrl”
parameter to “O” (Enable). Make this setting for
each timbre.
With the factory settings, “MIDI3” is set to #080
and “MIDI4” is set to #081.
On the RADIAS-R, SW1/SW2 operate only in toggle
mode. The on/off status will alternate each time you
press the switch. When you change programs, the
switch will be reset to the “off” state.
If you want MIDI control change messages to be
transmitted and received, set the Global mode P06:
MIDI FILTER page parameter “Ctrl Chg” to “O”
(Enable).
The lit/unlit status of the switch will depend on the
connector to which you’ve connected the unit.
If you want to use the joystick +Y axis as a
modulation source for another parameter, set the
following parameters to M.Wheel according to the
parameter that you want to control.
• Virtual patch P11 PATCH “Source” (RADIAS
owner’s manual p.91)
If the RADIAS-R is connected to the TO MODULE connector
If you connect the RADIAS-R to the TO MODULE
connector of the 61-key or 73/88 key keyboard
assembly, the status of the switch will match the
operation of the RADIAS-R. The switch will be lit when
on, and dark when off.
• Vocoder P07: FILTER “FcModSrc” (RADIAS
owner’s manual p.105)
• Effect control source (St.Filter “Ctrl Src,” etc.;
RADIAS owner’s manual p.125)
If the RADIAS-R is connected to the TO MODULE (2nd) con-
nector
On the 73/88-key keyboard assembly, the status of the
switch will reflect the setting of the module connected to
the TO MODULE connector, but will not reflect the
status of the module connected to the TO MODULE
(2nd) connector. When you operate the module
connected to the TO MODULE (2nd) connector, you’ll
need to be aware of the lit/dark state of the switch. If the
program etc. of the M3-M connected to the TO
MODULE connector was written into memory with an
SW1/SW2 setting of Toggle or Off, the switch status will
match the operation of the RADIAS-R connected to the
TO MODULE (2nd) connector.
–Y axis
By setting one of the Global mode P04: MIDI page
parameters “MIDI1”–“MIDI5” to #002, you can use the
–Y axis of the joystick as the following sources.
• Modulation source for a virtual patch (RADIAS
owner’s manual p.91)
• Modulation source for the vocoder filter (RADIAS
owner’s manual p.105)
• Effect control source (St.Filter “Ctrl Src,” etc.;
RADIAS owner’s manual p.125)
With the factory settings, “MIDI2” is set to #002.
The on/off status of the switch cannot be saved in
the RADIAS-R program.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
RADIAS synthesizer/vocoder
When you operate a switch, a control change CC#80
(SW1) or CC#81 (SW2) will be transmitted on the MIDI
channel of the timbre selected by TIMBRE SELECT.
Switch-on will transmit a value of 127, and switch-off
will transmit a value of 0. When CC#80 (SW1) or CC#81
(SW2) are received, the on/off status of the switch will
change. A value of 64 or higher will turn the switch on,
and a value of 63 or lower will turn it off.
The aftertouch sensitivity of the 73/88-key
keyboard assembly cannot be adjusted on the
RADIAS-R.
Ribbon controller
The ribbon controller is available only if the M3-M is
connected to the TO MODULE connector of the 73/88-
key keyboard assembly, or if the RADIAS-R is
connected to the TO MODULE (2nd) connector.
If one of the Global mode P04: MIDI page parameters
“MIDI1”–“MIDI5” are set to #016 , you’ll be able to use
the ribbon controller as a source for the following:
If you want to apply an effect using SW1/SW2, set
the Program Edit mode P03–5: TIMBRE CC-A tab
page “Cntrl” parameter to “O” (Enable). Make this
setting for each timbre.
If you want control change messages to be transmitted
and received, set the Global mode P06: MIDI FILTER
page parameter “Ctrl Chg” to “O” (Enable).
• Modulation source for a virtual patch (RADIAS
owner’s manual p.91)
• Modulation source for the vocoder filter (RADIAS
owner’s manual p.105)
• Effect control source (St.Filter “Ctrl Src,” etc.;
RADIAS owner’s manual p.125)
Keyboard aftertouch
Aftertouch from the keyboard is available only if the
M3-M is connected to the TO MODULE connector of the
73/88-key keyboard assembly, or if the RADIAS-R is
connected to the TO MODULE (2nd) connector.
If one of the Global mode P04: MIDI page parameters
“MIDI1”–“MIDI5” are set to A.Touch, you’ll be able to
use keyboard aftertouch as a source for the following:
With the factory settings, “MIDI1” is set to #016.
If “MIDI1” is set to #016, the effect may not return
to 0 when you take your hand off the ribbon
controller. If you want the effect to return to 0 when
you take your hand off the ribbon controller, set
“MIDI1” to #016 .
• Modulation source for a virtual patch (RADIAS
owner’s manual p.91)
• Modulation source for the vocoder filter (RADIAS
owner’s manual p.105)
• Effect control source (St.Filter “Ctrl Src,” etc.;
RADIAS owner’s manual p.125)
When you operate the ribbon controller, control change
CC#16 messages will be transmitted on the MIDI
channel of the timbre that is selected in TIMBRE
SELECT. When CC#16 is received, the result will be the
same as when you operate the ribbon controller.
If you want to use the ribbon controller to apply an
effect, set the Program Edit mode P03–5: TIMBRE
CC-A tab page “Cntrl” parameter to “O” (Enable).
Make this setting for each timbre.
With the factory settings, “MIDI5” is set to
A.Touch.
When you apply keyboard aftertouch, channel
aftertouch messages will be transmitted on the MIDI
channel of the timbre that is selected in TIMBRE
SELECT. When channel aftertouch is received, the result
will be the same as when you operate the keyboard.
If you want control change messages to be
transmitted and received, set the Global mode P06:
MIDI FILTER page parameter “Ctrl Chg” to “O”
(Enable).
If you want to use aftertouch to apply an effect, set
the Program Edit mode P03–4: TIMBRE-MIDI tab
page “AT” parameter to “O” (Enable). Make this
setting for each timbre.
If you connect the RADIAS-R to the TO MODULE
connector, the ribbon controller will be
unavailable. If you connect the RADIAS-R to the
TO MODULE connector and the RADIAS-R or M3-
M to the TO MODULE (2nd) connector, not only
will the ribbon controller be unavailable, but the
RADIAS-R or M3-M connected to the TO
MODULE (2nd) connector may malfunction when
you operate the ribbon controller. If you make
connections in this way, please disable ribbon
controller reception on the RADIAS-R or M3-M
that is connected to the TO MODULE (2nd)
connector.
If you want aftertouch messages to be transmitted
and received, set the Global mode P06: MIDI
FILTER page parameter “Ctrl Chg” to “O” (Enable).
If you connect the RADIAS-R to the TO MODULE
connector, the keyboard’s aftertouch will be
unavailable. If you connect the RADIAS-R to the TO
MODULE connector and the RADIAS-R or M3-M to
the TO MODULE (2nd) connector, not only will the
keyboard’s aftertouch be unavailable, but the
RADIAS-R or M3-M connected to the TO MODULE
(2nd) connector may malfunction when you use
aftertouch. If you make connections in this way,
please disable aftertouch reception on the RADIAS-
R or M3-M that is connected to the TO MODULE
(2nd) connector. (In the Program Edit mode P03–4:
TIMBRE-MIDI tab page, set “AT” to “x”.)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Function added in system version 2.0
Global parameters
MIDI settings when using an
M3-M and RADIAS-R together
So that you can connect the RADIAS to the 61-key/73-
key/88-key keyboard assembly used by the M3 music
workstation/sampler and play the RADIAS from that
keyboard, RADIAS version 2.0 adds the following
functions as choices that can be selected in “MIDI1”–
“MIDI5” (☞p.117 P04–1: MIDI page “MIDI1”–
“MIDI5”).
MIDI OUT
MIDI IN
M3-M
RADIAS-R
#016 (CC#16 )
Select this if you want to use the ribbon controller of the
keyboard assembly as a modulation source for the
virtual patch.
TO MODULE
TO MODULE(2nd)
The ribbon controller will produce a control change
value of 64 when you release your hand.
Keyboard Assembly 73/88
When using the ribbon controller of the 73-key or
88-key keyboard assembly, you may not obtain the
expected result unless you select #016 .
Preventing the RADIAS-R from double
triggering
#017 (CC#17 ), #019 (CC#19 ),
#020 (CC#20 ), #021 (CC#21 )
Select these if you want to use the MIDI control changes
transmitted by the four user sliders (Modulation Sliders
5, 6, 7, and 8) of the M3 control surface as modulation
sources for virtual patches.
If you have made the connections shown above–for
example to synchronize the tempo of the M3-M and the
RADIAS-R–messages such as note-on from the TO
MODULE (2nd) connector and the MIDI messages from
the M3-M’s MIDI OUT connector may cause the
RADIAS-R to sound duplicate notes. To prevent this,
make the following settings.
• RADIAS-R GLOBAL P04–1 MIDI page “Clock”: Exter-
nal MIDI or Auto (RADIAS owner’s manual p.117)
• RADIAS-R GLOBAL P04–1 MIDI page “LocalCtrl”:
Off (RADIAS owner’s manual p.116)
For #017 , #019 , #020 , and #021 , the resulting
modulation will be zero when the slider etc. is set
to the center position (control change value of 064).
For #017, #019, #020, and #021, the resulting
modulation will be zero when the slider etc. is set
to the “0” position (control change value of 0).
Select the choice that will give you the desired type
of change when you operate the slider or other
controller.
If you turn the RADIAS-R’s local control (“LocalCtrl”)
off, note-on messages etc. from the TO MODULE (2nd)
connector will not be received.
Preventing KARMA generated note
data from being received by the
RADIAS-R
Monitoring the audio output of
the M3-M and RADIAS-R
If you would like an easy way to monitor the audio
output of the M3-M and RADIAS-R without using a
mixer or similar device, connect the RADIAS-R’s MAIN
OUT jacks to the M3-M’s AUDIO INPUT jacks, set the
M3-M’s rear panel AUDIO INPUT [MIC/LINE] switch
to LINE, and set the Global P0: Basic Setup- Audio page
“Bus Select” setting to L/R. With these settings, you’ll
be able to monitor the sound via the M3-M’s headphone
jack (or main output jacks). To adjust the volume, use
the M3-M’s rear panel AUDIO INPUT [LEVEL] knob
and the RADIAS-R’s [VOLUME] knob.
If you have made the connections shown above and are
playing an M3-M program or combi that uses KARMA
(such as a rhythmic drum program generated by KARMA),
the note data from the KARMA module may be
transmitted to the RADIAS-R. To prevent this, make the
following settings
.
• M3-M Global P1: MIDI- MIDI Routing page “Enable
KARMA Module to MIDI OUT”: Off
• RADIAS-R GLOBAL P04–1 MIDI page “LocalCtrl”:
On (RADIAS owner’s manual p.116)
With these settings, the M3-M will not transmit note
data from the keyboard either, so turn the RADIAS-R’s
“LocalCtrl” setting On.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4015-2 Yanokuchi, Inagi-city, Tokyo 206-0812 Japan
2007 KORG INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
|