USER’S GUIDE
IP-011
Before printing read this guide.
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure to read before use
Thank you very much for purchasing the "Konica Printer Controller IP-011."
Konica Corp. ("Konica") allows you to use the software attached to the IP-011 only when you agree to its
"Software License Agreement." If you do not agree to terms of this agreement, return the software to the
distributor from which you purchased it prior to use.
Software License Agreement
Carefully read all terms and conditions of the agreement which will be shown during the software instal-
lation.
Printed in Japan KONICA CORPORATION
IP-011 Printer Controller i
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
■ Contents
■ Contents.............................................................................................................................. ii
■ Introduction .........................................................................................................................v
■ About Supplied Items ..........................................................................................................v
■ About Positioning of This Manual ....................................................................................... vi
■ About Composition of This Manual .................................................................................... vi
■ System Requirements....................................................................................................... vii
● Windows.................................................................................................................................. vii
■ Rules in This Manual........................................................................................................ viii
Chapter 1 Outline........................................................................................... 1-1
■ Contents of This Chapter ................................................................................................. 1-2
■ Outline of the Printer Controller ....................................................................................... 1-3
● IP-011 and Printer Engine .................................................................................................... 1-3
● IP-011 Hardware Configuration ............................................................................................ 1-4
● I/O Interface .......................................................................................................................... 1-4
● Data Flow .............................................................................................................................. 1-5
● How to Use Memory ............................................................................................................. 1-6
● General View......................................................................................................................... 1-7
■ About the Printer Tools ..................................................................................................... 1-8
● About the Printer Tools.......................................................................................................... 1-8
● About the Status Monitor ...................................................................................................... 1-8
● About the Control Panel ........................................................................................................ 1-8
■ About the Printer Driver ................................................................................................... 1-9
● Compliant OS........................................................................................................................ 1-9
Chapter 2 Setup ............................................................................................. 2-1
■ Contents of This Chapter ................................................................................................. 2-2
■ Installation of the Printer Driver........................................................................................ 2-3
● Before Installation ................................................................................................................. 2-3
● Files to be Installed ............................................................................................................... 2-3
● Installation to Windows95/98 ................................................................................................ 2-4
● Installation to WindowsNT4.0................................................................................................ 2-7
● Uninstallation of the Printer Driver ...................................................................................... 2-10
■ Test Print ........................................................................................................................ 2-11
■ Print from Applications ................................................................................................... 2-12
● Execution of Printing ........................................................................................................... 2-12
● Print Settings ...................................................................................................................... 2-12
Chapter 3 Printer Driver ................................................................................ 3-1
■ Contents of This Chapter ................................................................................................ 3-2
■ Working Environment ...................................................................................................... 3-3
● Compliant OS........................................................................................................................ 3-3
■ Property of Printer Driver ................................................................................................ 3-3
ii IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
■ Printer Driver Function List .............................................................................................. 3-5
■ Description of Printer Driver Functions (in the alphabetic order) ..................................... 3-8
● Alphabetic Order ................................................................................................................... 3-8
Driver Function Combination List...................................................................................... 3-.23
Chapter 4 Operation Panel Setup................................................................ 4-1
■ Contents of This Chapter ................................................................................................. 4-2
■ About the LCD Panel ....................................................................................................... 4-3
● The LCD Panel of the Copier ................................................................................................ 4-3
● How to Enter Settings on the LCD Panel .............................................................................. 4-4
● Printer Mode Basic Screen ................................................................................................... 4-5
● Printer Menu Screen ............................................................................................................. 4-5
● Printer Setting screen ........................................................................................................... 4-6
● Procedures of the Printer Setting.......................................................................................... 4-7
■ Configuration of Printer Setting Menu .............................................................................. 4-9
■ Functions of the Printer Setting...................................................................................... 4-11
● Network Setup .................................................................................................................... 4-11
● Select Language ................................................................................................................. 4-11
● Print Quality ........................................................................................................................ 4-12
● I/O Timeout ......................................................................................................................... 4-12
● Test Print ............................................................................................................................. 4-13
● CMD Error Page ................................................................................................................. 4-13
● Error Page........................................................................................................................... 4-13
● Factory Default.................................................................................................................... 4-14
● Help..................................................................................................................................... 4-14
Chapter 5 Status Monitor and Control Panel ............................................. 5-1
■ Contents of This Chapter ................................................................................................. 5-2
■ Status Monitor and Control Panel .................................................................................... 5-3
● About the Status Monitor ...................................................................................................... 5-3
● About the Control Panel ........................................................................................................ 5-3
■ Working Environment ....................................................................................................... 5-4
● Compliant OS........................................................................................................................ 5-4
● Interface ................................................................................................................................ 5-4
■ How to Install.................................................................................................................... 5-4
■ How to Operate the Status Monitor ................................................................................. 5-5
● Starting the Status Monitor ................................................................................................... 5-5
● Finishing the Status Monitor ................................................................................................. 5-5
● Restarting the Status Monitor ............................................................................................... 5-5
● Show/Hide the Status Monitor .............................................................................................. 5-6
● Display Change..................................................................................................................... 5-7
● How to Operate the Control Panel ....................................................................................... 5-8
● Starting the Control Panel..................................................................................................... 5-8
● Finishing the Control Panel ................................................................................................... 5-8
● Buttons of the Control Panel ................................................................................................. 5-9
● Settings of Paper ................................................................................................................ 5-10
● Printer Setting ..................................................................................................................... 5-11
● Test Print ............................................................................................................................. 5-12
● Confirmation of Configurations ........................................................................................... 5-12
IP-011 Printer Controller iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Appendix A Troubleshooting .................................................... Appendix A-1
■ Error Message ................................................................................................. Appendix A-2
■ Basic Troubleshooting ...................................................................................... Appendix A-3
■ General Problems of Printing ........................................................................... Appendix A-3
● The “OHT Film” is not selectable. ......................................................................... Appendix A-3
● The Printer Controller does not respond to the “Print” command. ........................ Appendix A-3
● A message to demand a paper size which you do not use is displayed. .............. Appendix A-4
●You can not print the test print............................................................................... Appendix A-4
● The print setting of a job does not correspond to the result of printing. ................ Appendix A-5
● The “Duplex” option is not displayed. .................................................................... Appendix A-5
● Memory Error / Memory Overflow / Overrun ......................................................... Appendix A-5
Appendix B Product Specifications......................................... Appendix B-1
■ Product Specifications ..................................................................................... Appendix B-2
Index .......................................................................................................Index -2
iv IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
■ Introduction
The IP-011 Printer Controller works as an interface between the Konica 7020 series Copier and a workstation,
and enables direct printing from a workstation environment.
The printer engine on the printer side and the optional network board include operating manuals (7020 series
operating manual/KN-304 operating manual (CD)) respectively.
For the detailed operations of Windows95/98 and Windows NT, refer to operating manuals of each operating
system. For operations of applications, refer to operating manuals which are attached to each application.
FCC Regulations
This equipment has been tested and found to comply with limits for a Class B digital device,
pursuant to part 15 of FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from the circuit to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Canadian Department of Communications Regulations
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This Class B digital apparatus complies with Canadian ICES-003.
About Registered Trademarks
Microsoft, MS and MS-DOS are registered trademarks of Microsoft Corporation in the United
States.
IBM is a registered trademark of International Business Machine, Inc. in the United States.
WindowTM is a trademark of Microsoft Corporation.
Destiny® is a registered trademark of Destiny Technology Corporation.
LaserAct® is a registered trademark of Destiny Technology Corporation.
DPOS® is a registered trademark of Destiny Technology Corporation.
WinStyler®-Nozomi™ is a registered trademark of Destiny Technology Corporation.
WinPane® is a registered trademark of Destiny Technology Corporation.
Other company names and product names written in this manual are the registered trademarks or
trademarks of their respective companies.
Copyright
LaserAct® 6 CopyrightC1992-1999,Destiny Technology Corp.Ver.2.0.All Rights Reserved.
WinStyler®-NozomiTMCopyrightC1995-1999,Destiny Technology Corp.Ver.2.0.All Rights Reserved.
WinPanel®CopyrightC1995-1999,Destiny Technology Corp.Ver.1.0.All Rights Reserved.
IP-011 Printer Controller v
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
● A part or all of this operating manual shall not be used or copied without permission.
● Konica shall have no liability for any influences caused by using the 7020 series copier +IP-011 system and this
manual.
● Information written in this operating manual is subject to change without notice.
● Konica Corp. shall have the copyright of this printer driver.
● This printer driver shall not be copied except for the purpose of backup.
● A part or all of this operating manual shall not be used or copied without permission.
● Konica shall have no liability for any influences caused by using this printer driver and the operating manual.
■ About Supplied Items
The following items are supplied to the IP-011 Printer Controller:
• User Software CD ( Including USER’S GUIDE (this manual))
• Release Note (The latest information and limits of the system and the user software are written.)
vi IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
■ About Positioning of This Manual
This manual describes how to operate the Printer Controller Konica IP-011 when the Konica 7020 series copier is
used as a printer by connecting it to computers or your network.
An optional network board (KN-304) is required so as to use the Konica 7020 series copier as a
printer by connecting it to your network.
Refer to the "7020 series operating manual" and the "KN-304 operating manual" which are
attached to the Printer Engine (7020 series) on the printer side and the optional Network Board
(KN-304) respectively for their operations.
■ About Composition of This Manual
This manual is composed of the following five chapters and Appendix:
Chapter 1: Outline
Chapter 1 describes the Printer Controller' hardware and the outline of its functions, and briefly
explains how to connect the parallel ports of computers to the Printer Controller and the Printer
(7020 series).
Chapter 2: Setup
Chapter 2 describes how to install the user software which is supplied in the user software CD to
the Windows*-compliant computers. Installing the user software enables printing from each
application of the Windows*-compliant computers to the Printer (7020 series) by way of a network/
parallel port.
Chapter 3: Printer Driver
Chapter 3 describes the corresponding environment and various functions of the Printer Driver
installed to the Windows*-compliant computers.
Chapter 4: Operation Panel Setup
Chapter 4 describes the layout of the operation panel of the Printer (7020 series) and how to
operate and set functions on the operation panel.
Chapter 5: Status Monitor/Control Panel
Chapter 5 describes the layout of the status monitor and the control panel shown on the Windows*-
compliant computers and how to operate and set functions on the status monitor or the control
panel.
Appendix
Appendix describes error messages and trouble-shootings inherent in the Printer Controller and
product specifications and functions.
IP-011 Printer Controller vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
■ System Requirements
● Windows
The following are required to print from the Windows*-compliant computers to the Printer Controller.
• Computers on which Windows 95/98, WindowsNT 4.0 can run
• CD-ROM drive (necessary to install the user software)
In case of using Windows 95/98
• Microsoft Windows 95/98
• 32MB RAM or more
In case of using Windows NT 4.0
• Microsoft Windows NT 4.0 and NT Service Pack 3
• 32MB RAM or more
Parallel Port
The following are required to print to the Printer Controller by way of the parallel port.
• Windows-compliant computers
• Minimum RAM capacity suitable for computers (Refer to the section of each operation system
described above.)
• IEEE 1284 parallel cable
One end of the cable is required to have an amphenol 36 pin male connector (connected to the
Printer Controller).
viii IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
■ Rules in This Manual
• Notation of a name of each section in this manual
It is written within [ ] (round brackets). (e.g. [Chapter 1: Outline ])
• Notation of names shown on the screen
They are written within [ ](braces). (e.g. Click the [OK] button.)
• Notation of cautions
In this manual, important items to be paid attention to are written with marks.
Each mark used in this manual has the following meaning.
Precautions and limits at the time of operating hardware or software are written.
Hints, advice, confirming items, etc. at the time of operating hardware or software are written.
• Notation of sub-folders
Sub-folders are written as “\route level folder\sub folder 1\sub folder 2.”
For example, at the time of double-clicking the [Setup.exe] icon in the [WIN_95] folder in the [PS_DRVR] folder
in the [INTALRS] folder of the User Software CD, it is written as
e.g. Double-click the [Setup.exe] icon in the “\INTALRS\PS_DRVR/WIN_95 ” folder of the User Software CD.
IP-011 Printer Controller ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Outline
■ Contents of This Chapter ............................................................ 1-2
■ Outline of the Printer Controller .................................................. 1-3
● IP-011 and Printer Engine ........................................................................... 1-3
● IP-011 Hardware Configuration ................................................................... 1-4
● I/O Interface ................................................................................................. 1-4
● Data Flow .................................................................................................... 1-5
● How to Use Memory .................................................................................... 1-6
● General View ............................................................................................... 1-7
■ About the Printer Tools................................................................ 1-8
● About the Printer Tools ................................................................................ 1-8
● About the Status Monitor ............................................................................. 1-8
● About the Control Panel............................................................................... 1-8
■ About the Printer Driver .............................................................. 1-9
● Compliant OS .............................................................................................. 1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Outline
■ Contents of This Chapter
This chapter describes the outline of the Konica IP-011 Printer Controller. For the Copier, Konica 7020 series to
which the Konica IP-011 Printer Controller is attached, refer to the operating manual of the Copier.
1-2 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Outline
■ Outline of the Printer Controller
● IP-011 and Printer Engine
The Konica IP-011 is the Printer Controller (IP-011) which is used to connect the Copier, Konica
7020 series (Konica 7020 series) to computers or a network and to use the Konica 7020 series as
a printer from applications on Windows 95/98 or Windows NT (In order to connect to a network, the
optional Konica KN-304 network board is required.).
When the command for printing is executed from applications on Windows 95/98 or Windows NT,
print data is sent to the IP-011 by way of a parallel cable (IEEE 1284) or a network. Then, the IP-
011 rasterizes the print data to image data, which is sent to the Konica 7020 series Printer Engine
by way of the PCI bus.
The IP-011 can receive the command for printing from applications even while the Printer Engine is
printing the previous print jobs or receiving data.
The 7020+IP-011 system can continuously print A4-size paper at the print speed of 20 ppm. In
addition, this system supports the duplex function and the finisher function which enables using
four paper trays, alternate printing and stapling.
Conceptual Connection
In case of using as a networked printer
*The Konica KN-304 is required.
In case of using as a local printer
E-RDH (Electronic Recirculating Document Hander)
The E-RDH is a system which temporarily saves print data in the memory of the Konica 7020
series to perform printing in accordance with the selected option. In order to print from the IP-011,
the E-RDH of the 7020 series is used. The E-RDH memory of the Konica 7020 is 32 MB (standard)
and can be extended to 288 MB at the maximum.
In the IP-011, the E-RDH is used in the 1 bit mode. Data of approximately 180 pages of A4-size
paper can be saved in the 32 MB (standard) E-RDH memory.
Copy Mode and Printer Mode
The operation panel of the Konica 7020 series can be used either in the copy mode or the printer mode.
Even while the Konica 7020 series is printing or copying, the IP-011 can receive the next job, and
while the IP-011 is receiving a print job, you can execute copying.
IP-011 Printer Controller 1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Outline
● IP-011 Hardware Configuration
Basic Configuration
Configuration of the IP-011 is as follows:
Control board
CPU: Power PC 401 GF
Program memory: FLASH ROM
System memory: 16MB SD-RAM
Memory
The IP-011 is equipped with 16 MB memory as standard and can be expanded to 80 MB at the
maximum.
● I/O Interface
Parallel
Centronics (IEEE1284)/ amphenol 36 pin male connector
Card Edge Type/20MHz/32bit
PCI Bus
Ethernet (option)
100Base-T and 10Base-T
The optional KN-304 card is used to connect to the Ethernet. The KN-304 is the internal print
server card which supports multiple protocols on the Ethernet. This card includes a CPU and a
flash memory with an upgradable program.
The KN-304 supports the following network protocol.
• IPX/SPX (NetWare)
• LPD/LPR (TCP/IP)
• Peer to peer (TCP/IP)
Refer to the corresponding operating manual for connection to the KN-304.
1-4 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Outline
● Data Flow
Computer
Printer Tools
Application
Browser
HTML
Status Monitor
Control Panel
Printer Driver
Spooler
Interface
IEEE1284
Network (TCP/IP,IPX/SPX)
Network
(TCP/IP,IPX/SPX)
IEEE1284
NIC
Printer Controller
IEEE1284
Intermediate Language Interpreter
Memory
IP-011
Command for Printing
Image Data
Engine Status
Printer Engine
PCI Bus
E-RDH Memory
Engine
IP-011 Printer Controller 1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Outline
● How to Use Memory
Most of memory of the IP-011 is used for rasterizing images and a part of it is used for the system operation. In
addition, E-RDH memory of the Konica 7020 series is used for print processing.
The basic memory settings of the IP-011 is 16MB, which allows 1 bit mode (600 dpi) printing for all sizes of paper.
The memory of the IP-011 can be expanded to 80MB at the maximum. In addition, the E-RDH memory of the
Konica 7020 can be expanded to 288MB at the maximum.
The more memory the IP-011 has, the more pages are rasterized during waiting the printing of the previous job.
When the A4-size paper is used, approximately 4,345 KB memory is used to print 1 bit data in 600dpi.
Memory Upgrading
In order to obtain the optimum printer performance, memory expansion is recommended.
Contact service providers for details.
1-6 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Outline
● General View
The IP-011 is mounted to the Konica 7020 series. The following is the general view.
IP-011
Parallel Port
The IP-011 is attached to the
back side of the Konica 7020
series.
Konica 7020
IP-011 Printer Controller 1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Outline
■ About the Printer Tools
● About the Printer Tools
When you install printer driver with “setup.exe” held in the CD-ROM to the computer connected to the system of
Konica 7020 series and IP-011, you can select simultaneous installation of the Printer Tools. The Printer Tools is
the generic name of two programs, “Status Monitor” and “Control Panel.” The Printer Tools enable you to monitor
the printer status from computers and to perform printer settings. Refer to “5 Status Monitor and Control Panel”
(5-1 page) for details of the Printer Tools.
● About the Status Monitor
If you set the Status Monitor to automatically start up at the time of installing the Printer Tools, when computers
connected to the 7020 series + IP-011 system are started up, the Status Monitor which is a program to monitor
the printer status automatically starts up. Refer to “2 Setup” (2-1 page) for installation of the printer driver. Refer to
“5 Status Monitor and Control Panel ” (5-1 page) for details of the Status Monitor.
● About the Control Panel
When [Printer Setting] on the [setup] menu of the Status Monitor is selected by clicking it, the Control Panel which
is a program to perform printer settings starts up. Refer to “5 Status Monitor and Control Panel” (5-1 page) for
details of Control Panel.
1-8 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Outline
■ About the Printer Driver
● Compliant OS
The printer driver can be used on the following OS.
Windows 95
Windows 98
Windows NT 4.0
Windows 2000 (to be supported)
Refer to “2 Setup” (2-1 page) for how to install the printer driver.
Refer to “3 Printer Driver” (3-1 page) for detailed functions of the printer driver.
IP-011 Printer Controller 1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
■ Contents of This Chapter ............................................................ 2-2
■ Installation of the Printer Driver................................................... 2-3
● Before Installation ........................................................................................ 2-3
● Files to be Installed...................................................................................... 2-3
● Installation to Windows95/98 ....................................................................... 2-4
● Installation to WindowsNT4.0 ...................................................................... 2-7
● Uninstallation of the Printer Driver ............................................................. 2-10
■ Test Print ................................................................................... 2-11
■ Print from Applications .............................................................. 2-12
● Execution of Printing.................................................................................. 2-12
● Print Settings ............................................................................................. 2-12
IP-011 IP-011 Printer Controller 2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
■ Contents of This Chapter
In order to use the 7020 series +IP-011 system, it is required to connect the 7020 series +IP-011 system to
computers by way of the parallel port and to install the printer driver to the computers. This chapter describes how
to install the printer driver and how to print from applications.
Refer to “Chapter 1 Outline” (1-7 page) for the detailed method of connecting to the parallel port.
Refer to “Chapter 3 Printer Driver” (3-1 page) for functions of the printer driver.
2-2 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
■ Installation of the Printer Driver
● Before Installation
Models and Environment of Computers
The Printer Controller for Konica 7020 series, IP-011, can be used with most computers ranging
from personal computers to workstations.
The IP-011 includes the printer driver for Windows95/98 and WindowsNT.
The printer driver can be installed to any models of computers as long as Windows95/98 and
WindowsNT have been installed to them.
About Windows95/98 and WindowsNT
Since on Windows95/98 and WindowsNT, the ways to manage the user interface and the printer
are different respectively, the ways to install the printer driver and the ways to print with the printer
vary. Therefore, the Konica IP-011 includes the printer driver for each Windows.
Please keep the “User Software CD” on hand since it is required to install the printer driver.
In this manual, the ways to install the printer driver to each Windows are explained in “Installation
to Windows95/98” and “Installation to WindowsNT4.0” separately. Please read the section of your
Windows.
● Files to be Installed
When the printer driver is installed with the “User Software CD”, the following files are installed to your computer.
The files to be installed vary, depending on the ways to install. Select an appropriate way.
Installation to Windows95/98
Installation to WindowsNT
Setup. exe
Setup. exe
(User Software CD)
Add Printer
Plug & Play
Add Printer
(User Software CD)
Printer Driver for 95/98
Printer Driver for NT
Konica IP-011
Printer Tools
Konica IP-011 Help
Konica IP-011 Readme
Uninstaller
IP-011 Printer Controller 2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
● Installation to Windows95/98
Perform the following steps to install the Konica IP-011 Printer Driver to Windows 95/98.
Please keep the “User Software CD” on hand since it is required to install the printer driver.
Installation with the “User Software CD”
Turn on the computer and start Windows.
When any Windows applications are active, exit from them.
Set the “User Software CD” on the CD-ROM drive.
Double-click the [My Computer] icon of the desktop to open the [My Computer] win-
dow.Then, double-click the active CD icon (user software CD).
Opening from the start menu
Right-click the [Start] button of the task bar to click [Explorer]. Then, you can select the active
CD iron (user software CD) from [Address].
Double-click the [95 nozomi] folder to double-click [Setup.exe] in the folder.
The [Konica IP-011 setup] screen will appear.Then, click the [Next] button.
The [Konica IP-011 Software License Agreement] screen will appear.Then, click the
[Yes] button.
To use the Konica IP-011 Printer Driver, you are required to agree to the license.
When you agree to the license, click the [Yes] button to proceed.
2-4 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
The [Type of Connection] screen will appear.Then, select [Local] and click the [Next]
button.
When the Konica 7020 series Copier (IP-011) is directly connected to a computer to which the
printer driver will be installed, select [Local].
In the case of selecting [Network]
When personal computers or workstations are connected to the network and, you want to print
by way of the network, connect to the optional network board (KN-304) and select [Network].
The screen to select a port will appear.Then, select the port to which the Konica 7020
series Copier is connected and click the [Next] button.
The [Printer Name] screen will appear.Then, specify the printer name and click the
[Next] button.
Default: [Konica IP-011]
The [Select Destination Path] screen will appear. Enter the location where you would
like to install the component and click the [Next] button.
Default: [C:\ Program Files\ Konica IP-011]
The [Select Components] screen will appear. Select the components you would like to
install and click the [Next] button.
Choice is made initially to install only the printer driver. To install Printer Tools together, put
the check mark of Printer Tools additionally.
When you print by way of the network, printer tools can not be operated. Remove the check
mark of the printer tools so as not to be installed.
If you have selected to install Printer Tools,The [Status Monitor Option] will appear.
When the [Yes] button is clicked, the status monitor of the printer will automatically start when
starting PC. When the [No] button is clicked, it will not automatically start.
The [Confirm Setup] screen will appear. Confirm the installed components and click the
[Next] button.
The [Setup Complete] screen will appear. Select the way to complete the setup and
click the [Finish] button.
The printer driver of the Konica IP-011 becomes available without restarting your computer.
The Konica IP-011 Printer Tools become available after restarting your computer.
IP-011 Printer Controller 2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
Installation by using [Add Printer]
In this method, only the printer driver is installed.
Turn on the computer and start Windows.
When the Windows applications are active, exit from them.
Click the [Start] button of the task bar.Then, select [settings] of the Start menu to click
[Printers] from the sub-menu.
The [Printers] window will open.
Opening from [My Computer]
You can open the [Printers] window by double-clicking the [Printers] folder after dowble-clicking
the [My Computer] icon of the desktop.
Double-click the [Add Printer] icon of the [Printers] window.
The [Add Printer Wizard] to install the printer driver will appear.
Then, follow the [Add Printer Wizard] to install the printer driver.
Installation by Using the Plug & Play
In this method, only the printer driver is installed.
Connect the IP-011 to a computer with the computer turned off.
Turn on the computer and start Windows
Devices compliant with the Plug & Play are automatically detected, and [Add New Hardware
Wizard] will appear.
.
Click the [Next] button.
The wizard to select the method of searching for the printer driver will appear.
Select [Search for the best driver for your device] and click the [Next] button.
The wizard to select the location to search for the printer driver will appear.
Set the “User Software CD” on the CD-ROM drive.Then, select [Specify a location] and
click the [Browse] button.
Click [95 nozomi] in the “User Software CD” and click the [OK] button.
Click the [Next] button.
Click the [Next] button.
Specify your printer's name and click the [Next] button.
Default: [Konica IP-011]
The print test confirmation screen will appear. Select whether you will perform the print
test or not and click the [Finish] button.
Select [Yes recommended] to perform the print test, while select [No] not to perform it.
Click the [Finish] button.
Necessary files will be copied from the “User Software CD” to finish the installation.
2-6 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
● Installation to WindowsNT4.0
Only authorized system administrators or printer administrators are allowed to install the Konica IP-011 printer
driver to WindowsNT4.0.
Please keep the “User Software CD” on hand since it is required to install the printer driver.
Printer Management on WindowsNT
Since WindowsNT is an operating system made specially for the network operation, it is equipped
with heavier security functions than other Windows.
According to the security level (access right) of the user, the range of operations and settings of the
installed printers allowed to the user is limited.
The following figure shows the access right of the Windows NT compliant printers and its operation
range.
Operation Range
Access Right
No rights
No operations of printers are allowed.
Execution of document printing and the following print
conditions of each document are allowed to be set.
• Operations related to printing
(selection of a paper size and a paper tray, etc.)
• Operations related to graphics
(processing of resolution and halftone, etc.)
• Printer functions (selection of functions peculiar to the copier)
Printing
Control of document setting
Document
Pause, restart, reprinting, and deletion of documents
Management
All of "Print" and "Document Management"
Pause and restart of the printer and deletion of all documents
Settings and changes of printer information
Deletion of the printer
Full control
Settings and changes of printer access rights
After installing the printer driver, set the appropriate access rights to printer users.
Refer to the “System Guide” of WindowsNT for how to set access rights of the printer.
IP-011 Printer Controller 2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
Installation by Using the “User Software CD”
Turn on the computer to start WindowsNT4.0.
.
.
Log on as an administrator (or a user entitled to install the Power User, etc.).
Set the “User Software CD” on the CD-ROM drive.
Double-click the [My Computer] icon of the desktop to open the [My Computer] win-
dow, and double-click the active CD icon (user software CD).
Opening from the start menu.
Right-click the [Start] button of the task bar to click [Explorer]. Then, you can select the CD icon
(user software CD) from [All Folder].
Double-click the [NT nozomi] folder to double-click [Setup.exe] in the folder.
The [Konica IP-011 Setup] screen will appear.Then, click the [Next] button.
The [Konica IP-011 Software License Agreement] screen will appear.Then, click the
[Yes] button.
To use the Konica IP-011 Printer Driver, you are required to agree to the license.
When you agree to the license, click the [Yes] button to proceed.
The [Type of Connection] screen will appear.Then, select [Local] and click the [Next]
button.
When the Konica 7020 series Copier (IP-011) is directly connected to a computer to which the
printer driver is to be installed, select [Local].
In case of selecting [Network]
When installing Konica IP-011 printer driver to win4.0 that does not conduct print service, select
[Network]. When the optional network board (KN-304) is used, refer to the user's manual of the
KN-304 to select the appropriate port.
2-8 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
The screen to select a port will appear.Then, select the port to which the Konica 7020
series Copier is connected and click the [Next] button.
The [Printer Name] screen will appear.Then, specify the printer name and click the
[Next] button.
Default: [Konica IP-011]
The [Select Destination Path] screen will appear. Select the location where you would
like to install the component and click the [Next] button.
Default: [C:\Program Files\Konica IP-011]
The [Select Components] screen will appear. Select the components you would like to
install and click the [Next] button.
Choice is made initially to install only the printer driver. To install Printer Tools together, put
the check mark of Printer Tools additionally.
When you print by way of the network, printer tools can not be operated. Remove the check
mark of the printer tools so as not to be installed.
If you have selected to install Printer Tools,The [Status Monitor Option] will appear.
When the [Yes] button is clicked, the status monitor of the printer will automatically start when
starting PC.When the [No] button is clicked, it will not automatically start.
The [Confirm Setup] screen will appear. Confirm the installed components and click the
[Next] button.
The [Setup complete] screen will appear. Select the way to complete the setup and
click the [Finish] button.
Installation by Using [Add Printer]
In this method, only the printer driver is installed.
Turn on the computer and start WindowsNT4.0.
.
.
Log on as an administrator (or a user entitled to install the Power User, etc.).
Click the [Start] button of the task bar.Then, select [settings] of the Start menu and
click [Printers] from the sub-menu.
The [Printers] window will open.
Opening from [My Computer]
You can open the [Printer] window by double-clicking the [Printers] folder after double-clicking
the [My Computer] icon of the desktop.
Double-click the [Add Printer] icon of the [Printers] window.
The [Add Printer Wizard] to install the printer driver will appear.
Then, follow [Add Printer Wizard] to install the printer driver.
IP-011 Printer Controller 2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
● Uninstallation of the Printer Driver
When any Windows applications are active, quit all of them.
.
Click the [Start] button of the task bar. Select [Settings] of the Start menu and click the
[Control Panel] of the sub menu.
The [Control Panel] window will open.
Opening from [My Computer]
You can open the [Control Panel] window by double-clicking the [Control Panel] folder after
double cliking the [My Computer] icon of the desktop.
Uninstalling by Using the Uninstaller
You can also delete the printer driver by clicking the [Start] button of the task bar to select
[Program] of the Start menu and then, selecting [Konica IP-011] to click [Uninstaller]. After
clicking [Uninstaller], go to the Step 6.
.
Double-click the [Add/Remove Programs] icon of the [Control Panel] window.
The [Add/Remove Programs Properties] dialog box will appear.
Click [Konica IP-011] in the [Install/Uninstall] list and click the [Add/Remove...] button.
Click the [Yes] button.
Click the [OK] button.
The screen to confirm unistallation will appear.
When the [OK] button is displayed, click the [OK] button.
The printer driver will be uninstalled by following the above steps.
2-10 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
■ Test Print
You can check whether the printer driver functions properly by performing a test print after the printer driver has
been installed.
Click the [Start] button of the task bar.Then, select [Settings] of the Start menu and
click [Printers] in the sub menu.
The [Printers] window will open.
Opening from [My Computer]
You can open the [Printers] window by double-clicking the [Printers] folder after double clicking
the [My Computer] icon of the desktop.
.
.
Right-click [Konica IP-011] and click [Properties].
[Konica IP-011 Properties] will appear.
Select [General] of [Konica IP-011 Properties] and click the [Print Test Page] button.
A test print will start and a screen to confirm print end will appear.
Click the [Yes] button.
A test print will end.
IP-011 Printer Controller 2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
■ Print from Applications
● Execution of Printing
Click the [File] menu of each application and click [Print].
.
Check that [Konica IP-011] is shown on [Printer Name] and click [OK].
When [Konica IP-011] is not shown, select it from the list box.
Setting the [Print] dialog box
Refer to the user's manual of each application.
Print settings of the printer driver
Refer to “Print Settings” (2-12 page) for print settings of the printer driver.
● Print Settings
Perform various settings at the time of printing on the printer driver setup screen.
Displaying the Setup Screen
Click the [File] menu of each application and click [Print].
.
Check that [Konica IP-011] is shown on [Printer Name] and click [Properties].
When [Konica IP-011] is not shown, select it from the list box.
[Konica IP-011 Printer Controller Driver Properties will appear.
2-12 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
Contents of Settings
Details of each setting are described as follows;
Items and their setting ranges shown on the screen and their descriptions are explained in
detail.The underlined setting ranges indicate the default settings.
[Setup] tab
[Copies]: 1 to 999
Specifies the number of copies of the print job.
[Orientation]: Portrait and Landscape
Specified the print orientation.
[Paper]-[Original Paper]
Specified the original size set on the application.
For Europe/Others : A3R, A4, A4R, A5R, B4R, B5, B5R, B6R, 8K, 16K, 16KR, F4, Ledger,
Legal, Statement, Letter and Letter R
For US:
A3, A4R, A4, A5R, B5R, B5, Legal, Letter, Letter R and Statement
[Paper]-[Paper size]
Specifies the paper size used for printing.
For Europe/Others : A3R, A4, A4R, A5R, B4R, B5, B5R, B6R, 8K, 16K, 16KR, F4, Ledger,
Legal, Statement, Letter and Letter R
For US:
A3, A4R, A4, A5R, B5R, B5, Legal, Letter, Letter R and Statement
[Paper]-[Zoom]: 25% to 400% (default value: 100%)
Specifies the expansion and reduction rates at the time of printing.
[Paper]-[Paper Tray]: Auto, Tray 1, Tray 2, Tray 3, Tray 4 and Bypass tray
Specifies the paper tray which holds the paper to be used for printing.
When [Auto] is specified, papers are automatically fed from the tray that has a appropriate
paper size specified by a user.
When [Bypass tray] is specified, you can feed paper from the bypass tray.
In order to specify [Tray 3] or [Tray 4], the DB (optional Paper Tray) must be attached to the
copier.
IP-011 Printer Controller 2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
[Image]-[Layout]: 1-Up, 2-Up, 4-Up, 8-Up and 9-Up
Specifies how many pages of documents are gathered on one piece of paper. The default
value, [1-Up(Default)], indicates that an one-page document is printed on one piece of paper.
[Image]-[Print Page Borders]: Default value (not printing: without a check mark)
Specifies whether borders are printed or not between documents when they are gathered on
one piece of paper.
[Image]-[Staple]: off, 1-Left, 1-Right, 2-Left, 2-Top and 2-Right
Specifies the number of staples to be used and their positions.
When [off] is selected, documents are not stapled.
The staple function is supported when the finisher is attached.
[Image]-[Duplex]: 1-Sided, 2-Sided Long Edge Binding, 2-Sided Short Edge Binding and Booklet
[1- Sided] prints only one side.
[2- Sided Long Edge Binding] prints both sides so that heads of both sides become upward
while [2-Sided Short Edge Binding] prints both sides so that the head of one side becomes
the bottom of the other side.
[Booklet] prints in consideration of making booklets.
[Output]-[Output Tray]: Printer's default, Tray 1, Tray 2, Tray 3 and Tray 4
Specifies the way to output.
When [Printer's default] is selected, the output tray specified on [Paper] of the control panel
will be used for output.
In order to specify [Tray 2], [Tray 3] and [Tray 4], it is required that a finisher is attached to the
Copier and that the [Finisher] option must be selected.
[Output]-[Alternate]: On and Off
This setting is available only when the finisher is not attached. The output direction of paper
is changed every set of copy.
[Output]-[Sorting]: Sort and Group
Specifies how to output the multiple pages and multiple copy jobs.
[Engine Display]:
Shows the external view of the copier system.
[About] button:
Shows information on the version of the printer driver.
[Default] button:
Returns to the default value.
2-14 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
[Paper] tab
[Front Cover]: On, Off, Blank and Printed
Specifies whether a front cover is attached or not. Also specifies whether the front cover is
blank or printed when it is attached.
[Back Cover]: On, Off, Blank and Printed
Specifies whether a back cover is attached or not. Also specifies whether the back cover is
blank or printed when it is attached.
[Front/Back Cover]-[Paper Tray]: Tray 1, Tray 2, Tray 3, Tray 4 and Bypass Tray
Specifies the output tray where paper for a front cover or a back cover is set.
[Front/Back Cover]-[Paper Type]: Plain
Specifies the paper type of a front cover or a back cover.
[Paper Type]: Plain, OHT Film, OHT Interleave and OHT Interleave Printed
Specifies the paper type of other paper than a front cover or a back cover.
IP-011 Printer Controller 2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
[Print Quality] tab
[Smoothing]: Off, Type 1, Type 2 and Type 3
Specifies the smoothing type. This function is unavailable for US.
Type 1: processes suitable for oblique lines of general characters and pictures
Type 2: processes suitable for curves of general characters
Type 3: processes suitable for curves of decorated characters and fine characters
[Page Protection]: Auto and On
Specifies how to protect page data.
The page protection is a function to secure memories required to print complicated charac-
ters or image documents in advance, and completely create one-page print data before
actual printing starts.
This function secures printing of each page and avoids the memory overrun error.
Normally, set this setting to [Auto]. If any errors occur, try to set it to [On]. Setting it to [On]
decreases the printing speed and requires more memories, but may reduce printing errors.
[Option] tab
[Finisher]: None, 2 Trays, 3 Trays and 4 Trays
Specifies the finisher of the copier option.
[Option Tray]: None, DB-209(2 Trays) and DB-409(1 Tray)
Specifies the Option Tray of the copier option.
2-16 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
[Watermark] tab
[Watermark String]: None, CONFIDENTIAL, COPY, DRAFT, FILE COPY, FINAL, PROOF,
TOP SECRET
Specifies the watermark.
[First Page Only]
Prints the watermark on the first page only.
[Edit]
Edits the watermark.
(Refer to “[Edit/Add Watermark(Sub-Menu)] dialog box” on 2-18 page.)
[Add]
Adds new watermarks.
(Refer to “[Edit/Add Watermark(Sub-Menu)] dialog box” on 2-18 page.)
You can add up to 50 watermarks.
[Delete]
Deletes watermarks.
IP-011 Printer Controller 2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Setup
[Edit/Add Watermark(Sub-Menu)] dialog box
[Edit Text]
Specifies [Text], [Font], [Size] and [Style].
[Darkness]
Specifies the darkness of the edit text.
[Angle]: -90 degrees to +90 degrees
Specifies the angle of the edit text.
[Position]: Automatic centering and Manual positioning
Specifies where on a page the edit text is put.
2-18 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
■ Contents of This Chapter ........................................................... 3-2
■ Working Environment ................................................................. 3-3
● Compliant OS .............................................................................................. 3-3
■ Property of Printer Driver ........................................................... 3-3
■ Printer Driver Function List ......................................................... 3-5
■ Description of Printer Driver Functions (in the alphabetic order) 3-8
● Alphabetic Order.......................................................................................... 3-8
■ Driver Function Combination List.............................................. 3-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
■ Contents of This Chapter
This chapter describes functions of the Printer Driver which is installed to computers from which the Konica 7020
series +IP-011 system is used from three different viewpoints, the function list and description of functions and the
list of combined functions in the alphabetic order.
Refer to “2 Setup” (2-1 page) for installation of the printer driver.
3-2 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
■ Working Environment
● Compliant OS
The Printer Driver can be used on the following OS.
Windows 95
Windows 98
Windows NT 4.0
Windows 2000 (to be supported)
Refer to “2 Setup” (2-1 page) for installation of the Printer Driver.
■ Property of Printer Driver
On the [Printer] window shown by clicking [Start]-[Settings]-[Printers], right-click the [KONICA IP-011] icon. When
[Properties] is clicked on the shown menu, [KONICA IP-011 Properties] will appear.You can set all functions of the
Printer Driver on [KONICA IP-011 Properties].
You can perform any printer settings but [General] tab / [Detail] tab / [Color Management] tab / [Share] tab of
[KONICA IP-011 Properties] from applications. Refer to “2 Setup” (2-1 page) for how to perform printer settings
from applications.
Additionally, refer to “4 Operation Panel Setup” (4-1 page) for how to perform printer settings from the 7020 series
operation panel and “5 Status Monitor and Control Panel” (5-1 page) for how to perform printer settings from the
Printer Tools.
[OK]
When the [OK] button is clicked, all tab settings are saved and close the properties screen.
[Cancel]
When the [Cancel] button is clicked, all tab settings are canceled and close the properties screen.
[Apply]
When the [Apply] button is clicked, the present tab settings are saved. This button is used when
settings continue to be performed by using other tabs, and the present tab settings are registered
before using other tabs.
IP-011 Printer Controller 3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
[Help]
When the [Help] button is clicked, Help of each tab will appear.
[General] tab
Enables a print test of a printer.
[Details] tab
Performs settings related to ports, drivers, timeout and spooling.
[Sharing] tab
Performs share settings of a printer.
[Setup] tab
Performs settings related to Copies, Original size, Paper Size, Magnification, Paper Tray, Output
Tray, Alternate, Sorting, Orientation, Layout, Staple and Duplex.
[Paper] tab
Performs settings related to Front Cover, Back Cover and Paper Type.
[Print Quality] tab
Performs settings related to Smoothing and Page Protection.
[Option] tab
Performs settings related to Finisher and DB.
[Watermark] tab
Performs settings related to Watermark.
3-4 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
■ Printer Driver Function List
The following list summarizes functions (Setting items) which can be set by using the Printer Driver of the Konica
7020 series +IP-011 system.
Refer to “■ Description of Printer Driver Functions (in the alphabetic order)” (3-8 page) for setting items of each
function.
Refer to “■ List of Combined Printer Driver Functions (in the alphabetic order)” (3-23 page) for combination of
each function.
In addition, refer to “2 Setup” (2-1 page) for how to perform printer settings from applications, “4 Control Panel
Setup” (4-1 page) for how to perform printer settings from the LCD panel and “5 Status Monitor and Control Panel”
(5-1 page) for how to perform printer settings from the Printer Tools.
Classification Setting Items
Set Value
Description
95/98
NT4.0
Port-
related
Matters
Time out setting
Not selected
This function is used to set
timeout of the parallel port and
resending time.
Transmission retry
Port settings
Spool MS-DOS
print job.
This function is used to set whether the
MS-DOS print job is spooled or not and
whether the status of the LPTx: port is
checked before printing or not.
Check port state
before printing.
Print to the follwing
port
COM1, COM2 FILE
and LPT1
This function is used to set
the printing port.
Capture a Printer port Device Reconnect
at log-on
This function is used to set the device
name and path of the printer at the
time of printing by way of a network
and whether reconnection is performed
or not at the time of log-on.
End capture
-
This function is used to unallocate
the network paths of unnecessary
network printers.
Add Port
Network and other
-
This function is used to add a port.
Delete port
This function is used to delete an
unnecessary port.
Driver-
related
Matters
New driver
-
This function is used to add a driver.
Spooling- Spooling settings
related
Matters
Spool print jobs so
program finishes
This function is used to set
spooling and bi-directional
communication functions.
pringing faster. Print
directly to the printer.
Enable bi-directional
support for this printer.
Disable bi-directional
support for this printer.
IP-011 Printer Controller 3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Classification
Setting Items
Layout
Set Value
Description
95/98
NT4.0
Konica
7020
1-Up (default): 2-Up,
4-Up, 8-Up and 9-Up
This function is used to print two pages,
four pages, eight pages or nine pages
of documents on one piece of paper.
special
functions
Print page borders
On and Off
This function is used to specify
whether borders are printed or not
between documents when they
are gathered on one piece of paper.
Staple
Duplex
Off, 1-Left, 1-Right,
This function is used to select the
2-Left, 2-Right and 2-Top staple position.
1- Sided, 2-Sided Long Edge
Binding, 2-Sided Short Edge
Binding and Booklet
This function is used to set the
way of the Duplex printing.
Alternate (available only when On and Off
the finisher is not attached)
This function is used to set the
Alternate printing to on or off.
Sorting
Sort and Group
This function is used to specify
how to output the multiple pages
Print quality setting
Smoothing
This function is used to specify about
Smoothing and Page Protection.
Off and On (Type 1 to 3)
Page Protection Auto and On
Front cover
Back cover
On, Off,
This function is used when
front covers are used.
Printed and Blank
On, Off,
This function is used when
back covers are used.
Printed and Blank
Front/Back cover
Paper Tray
Tray 1, Tray 2, Tray 3,
Tray 4 and Bypass
This function is used to select
an output tray used for front
covers and back covers.
Front/Back cover
Paper Type
Plain
This function is used to specify
the paper type used for printing
front covers or back covers.
Option
Finisher
None, 2 Trays
This function is used to select
the Finisher which is an optional
device of the copier.
3 Trays and 4 Trays
Drawer Base
Copies
None, DB-209(2 Trays) This function is used to select
and DB-409(1 Tray)
the DB which is an optional device
of the copier.
Paper-
related
matters
1 to 999
This function is used to specify
the number of copies to be printed
3-6 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Classification Setting Items
Original paper
Set Value
Description
95/98
NT4.0
USA / A3, A4, A4R, A5R, B5R, The original paper you can set differs
B5, Legal, LetterR, Letter, Statement depending on specifications in the country
Europe / A3, A4, A4R, A5R, B4 and trays.
B5, B5R, B6R, 8K, 16KR, 16K, F4
Ledger, Legal, LetterR, Letter,
Statement
Paper size
The same as
Original Paper
The paper sizes you can set differ
depending on specifications in the country
and trays. Refer to the operating manual
of the copier for details.
Zoom
25% to 400%
Auto select,
This function is used to specify the expand
and reduce rate of image in percentage.
Paper tray
Output tray
Orientation
Paper type
This function is used to specify
Tray 1 to 4 and Bypass the paper tray.
Printer's Default,
Tray 1 to 4
This function is used to specify
the output tray.
Portrait and
Landscape
This function is used to specify
the orientation.
Plain, OHT, OHT
Interleave and OHT
Interleave Printed
This function is used to specify
the paper type to be printed.
Water-
mark
Watermark
NONE,CONFIDENTIAL, This function is used to specify
COPY, DRAFT, FILE
COPY, FINAL, PROOF
and TOP SECRET
a watermark.
First page only
Edit
-
-
-
-
-
-
-
This function is used to print a
watermark on the first page only.
This function is used to edit
a watermark.
Add
This function is used to add
a watermark.
Delete
This function is used to delete
a watermark.
Others
About
This function is used to show version
information of the Printer Driver.
Default
This function is used to return
the settings to default settings.
Print test page
This function is used to perform
a test print.
IP-011 Printer Controller 3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
■ Description of Printer Driver Functions (in the alphabetic order)
Functions (setting items) which can be set with the Printer Driver are summarized in the alphabetic order. These
settings can be set by using [Start]-[Settings]-[Printers]- [KONICA IP-011] property. The tabs in this section are
those in the [KONICA IP-011] property.
● Alphabetic Order
A
About
When [Setup] tab-[About] button is clicked,
version information of the Printer Driver is
shown.
Add Port
When the port you would like to connect to is
not shown on the list shown by clicking the [▼]
button beside the [Details] tab-[Print to the
following port] , click [Details] tab-[Add Port]
button to add the port.
When the [Add Port] button is clicked, the [Add
Port] dialog is shown.
The following settings are performed on the
[Add Port] dialog;
When [Network] is selected to set a path to a network printer, you can add a network printer to a port.
When [Others] is selected to select the type of a port to be added, you can add the port
selected from a list.
Alternate
When the following conditions are satisfied, you
can perform settings of the alternate printing by
using [Setup] tab-[Alternate].
• When [None] is selected in the Finisher
settings, or when the Finisher is not
installed,
• When [A4], [Letter] or [B5] is selected in
the paper settings,
• When the same size of paper for both
portrait and landscape is set to the copier, (e.g.: A4/A4R,
and B5/B5R)
• When Front/Back Cover are not set and,
• When [Booklet] is not selected in the [Duplex].
When [On] is selected in the Alternate printing, every set of copies are output in a direction at
right angles to the previous set of copies.
e.g.
1st copy
2nd copy
3rd copy
2nd copy
1st copy
On
Off
3-8 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
B
Back cover
By using [Paper] tab-[Back Cover], you can
perform the setting to use a designated tray for
printing the last page.
Select either [On] or [Off].
Default of Back Cover is [None].
When [On] is selected, select either [Blank] or
[Printed].
When [Blank] is selected, nothing is printed
on the back cover.
When [Printed] is selected, the last page is printed on a back cover.
The tray for the back cover is selected by using [Front/Back Cover]-[Paper Tray].
Back Cover
[On] [Blank]
Back Cover
Back Cover [Off]
[On] [Printed]
[Not indicated]
Back Cover can not be set in the following conditions:
• When [B6R] is selected as a paper size,
• When Alternate is set to [On],
• When Duplex is set to [booklet], or
• When Sort is set to [Group]
C
Capture printer port
When the device name and path are specified
on the [Capture Printer Port] dialog shown by
clicking [Details] tab-[Capture Printer Port]
button, a network printer can be allocated as a
virtual printer port.
In addition, when [Reconnect at Logon] of the
[Capture Printer Port] dialog is selected, a
virtual printer port is automatically reconnected
at log-on.
IP-011 Printer Controller 3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Copies
Click the [▲] or [▼] button beside [Setup] tab-[Copies] or directly enter the number of copies from
the keyboard.
Default of the number of copies is 1.
D
Default
By clicking [Setup] tab-[Default] button, settings
of the [Setup] tab, [Paper] tab, [Print Quality]
tab, and [Watermark] tab return to defaults.
Delete port
When a port is specified on the [Delete Port]
dialog shown by clicking [Details] tab-[Delete
Port] button, and the [OK] button is clicked, you
can delete the specified port.
3-10 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Duplex printing
By using [Setup] tab-[Duplex], you can perform
settings of the Duplex printings.
You can select [1-Sided], [2-Sided Short Edge
Binding], [2-Sided Long Edge Binding] or
[Booklet] from the list shown by clicking the [▼]
button beside the [Duplex] box.
Default of the Duplex printing is [1-Sided].
When [1-Sided] is selected, only one side of
paper is printed.
[2-Sided Short Edge Binding], [2-Sided Long
Edge Binding] and [Booklet] can not be selected in the following conditions:
• When [B6R] is selected as a paper size
[Booklet] can not be selected in the following conditions as well:
• When other settings than [Letter], [Letter R], [Ledger], [A3], [A4], [A4R], [B4], [B5R] and [B5]
are selected as a paper size,
• When Staple is set to other settings than [Off],
• When Front/Back Cover is set, or
• When Alternate is set to [On].
[2-Sided Short Edge Binding]
Prints paper so that the head
A
of the front becomes the foot
A
of the back.
B
[2-Sided Long Edge Binding]
Prints paper so that heads of
both sides become upward
A
A
B
[Booklet]
Prints paper so that booklets are
made when it is folded into two.
IP-011 Printer Controller 3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
E
End Capture
When the virtual printer port is specified on the
[End Capture] dialog shown by clicking [Details]
tab-[End Capture] button, you can delete a
network printer allocated as a virtual printer
port.
F
Finisher
When the Finisher is attached to the copier,
you can select the Finisher setting from [None],
[2 Trays], [3 Trays] or [4 Trays].
Default of the Finisher is [None].
When [None] is selected in the Finisher
settings, or when the Finisher is not installed,
the function has limits as follows;
• You can not select other settings than
[Printer's Default] as an output tray.
• Staple settings can not be performed.
When [None] is selected in the Finisher settings, or when the Finisher is not installed, you can
perform the Alternate printing.
In this case, it is required that the same size of paper for both portrait and landscape is set to the
copier. (e.g.: A4/A4R, and B5/B5R)
Front Cover
By using [Paper] tab-[Front Cover], the setting
to print the first page from the designated tray
can be performed.
Select either [On] or [Off].
Default of Front Cover is [Off].
When [On] is selected, select either [Blank] or
[Printed].
When [Blank] is selected, nothing is
printed on the first page.
When [Printed] is selected, the first page is printed on the front cover.
The tray for front covers is selected by using [Front/Back Cover]-[Paper Tray].
Front Cover can not be set in the following conditions:
• When [B6R] is selected as a paper size,
• When Alternate is set to[On],
• When Duplex is set to [Booklet], or
• When sorting is set to [Group].
When Front Cover is set to [On], you can not use the Alternate printing and Sort.
3-12 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Front Cover
[Off]
Front Cover
Front Cover
[On] [Blank]
[On] [Printed]
[Not indicated]
Front/Back Cover- Paper Tray
Specify the tray for Front/Back Cover from the list shown by clicking the [▼] button beside the
[Paper] tab-[Front/Back Cover]-[Paper Tray] button.
The selection by using [Front/Back Cover]-[Paper Tray] must be different from that by using the
[Setup] tab-[Paper Tray].
Front/Back Cover-Paper Type
Specify the tray for Front/Back Cover from the list shown by clicking the [▼] button beside the
[Paper] tab-[Front/Back Cover]-[Paper Type] button.
G
Group
Refer to Sort.
L
Layout
By using [Setup] tab-[Layout], you can set how
many pages of documents are printed on one
piece of paper.
You can select 1-Up, 2-Up, 4-Up, 8-Up or 9-Up
from the list shown by clicking the [▼] button
beside the [Layout] box.
Default of Layout is [1-Up].
The layout is made as follows:
[1- Up]
[2-Up]
[4-Up]
IP-011 Printer Controller 3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
[8-Up]
[9-Up]
When [Booklet] is selected in the Duplex printing, [2-Up] is automatically selected and you can not
select other settings.
When [Setup] tab-[Print Page Borders] check box is selected, you can print borders between
gathered documents.
Default of Print Page Borders is no check mark.
When Layout is set to [1-Up], you can not select [Print Page Borders].
N
New Driver
To use drivers which are not displayed on the list shown by clicking the [▼] button beside [Details] tab-
[Print using the following driver] box, click the [New Driver] button. When a driver is changed, the
settings of presently shown property is saved and the property of a newly selected driver is shown.
O
Option
Refer to Finisher and DB.
Option Tray
When the Option Tray is attached to the Konica
7020, it is required to set the [Option Tray] in the
[Option] tab. Select either [DB-209] or [DB-409].
Default of the Option Tray is [None].
By setting the Option Tray, functions are limited
or enabled as follows;
When [None] is selected in the Option Tray
settings or when the Option Tray is not
installed, you can not select [Tray 3] and
[Tray 4].
When [DB-409] is selected in the Option Tray settings, you can not select [Tray 4] as a paper tray.
When [DB-209] is selected in the Option Tray settings, you can select all trays as a paper tray.
3-14 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Orientation
Select either [Portrait] or [Landscape] from the
list shown by clicking the [▼] button beside [Set
up] tab-[Orientation] box.
Default of Orientation is Portrait.
Output tray
Select an output tray from the list shown by
clicking the [▼] button beside [Setup] tab-
[Output Tray] box. When [None] is selected in
the Finisher settings, or When the Finisher is
not installed, other settings than [Printer's
Default] can not be selected.
P
Page protection
By using [Print Quality] tab-[Protection] box, you
can set Page Protection.Page Protection is a func-
tion to secure memory for printing complicated
characters and image documents in advance.
Page Protection completely develops one page
of print data before actual printing starts.This se-
cures printing of each page and avoid the memory
overrun error.
Select either [Auto] or [On] from the list shown
by clicking the [▼] button beside the [Page Protection] box.
Default of Page Protection is [Auto].
Normally, set this setting to [Auto]. If an error occurs, set it to [On]. When it is set to [ON], the print
speed decreases and more memory is used, but a print error may be reduced.
Paper tray
Select a paper tray you would like to use from
the list shown by clicking the [▼] button beside
[Setup] tab-[Paper Tray] box.
When [Auto] is selected, a paper tray with paper
which a user specified from an application by
using [Konica IP-011 Printer Controller Driver
Properties] is automatically selected.
In order to use ,[B6R], set to [Bypass].
In addition, when the bypass tray is selected,
you can select [OHT Film] from paper types of the [Paper] tab.
IP-011 Printer Controller 3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Paper type
[Plain], [OHT Film], [OHT Interleave] or [OHT Interleave Printed] can be selected from the list shown
by clicking the [▼] button beside [Paper] tab- [Paper Type] box.
When Front/Back Cover is set, you can select only Plain.
When [Tray 1], [Tray 2], [Tray 3] or [Tray 4] is selected by using [setup] tab-[Paper]-[Paper Tray], OHT
Film is not shown on the list.
When Paper Tray is set to [Bypass] and when [Sorting] is set to[Group], OHT Interleave and OHT
Interleave Printed are not shown on the list.
When the Duplex printing is set to other settings than 1-Sided,and when Staple is set to other settings
than Off, OHT Film, OHT Interleave and OHT Interleave Printed are not shown on the list.
Port settings
Click [Detail] tab-[Port settings] button to perform
settings of the port selected on the [Print to the
following port] box.
When the “LPT” is selected, the [Configure LPT
Port] dialog is shown by clicking the [Port
settings] button. The following settings are performed on the [Configure LPT Port] dialog.
When [Spool MS-DOS Print Job] is selected, a MS-DOS print job is spooled.
When [Check port state before printing] is selected, the port status is checked before printing.
Print page borders
Refer to Layout.
Print quality
Refer to Smoothing and Page Protection.
Print Test Page
Click [General] tab-[Print Test Page] button to
perform a test print.
Printing to the following port
Select the port name of the IP-011 from the list
shown by clicking the [▼] button beside
[Details] tab-[Printing to the following port] box
to change the printing port. Select a printing
port from [COM1], [COM2], [FILE], [LPT1] and
so on.
3-16 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Print using the following driver
Select the driver used for printing form the list shown by clicking the [▼] button beside [Details] tab-
[Print using the following driver] box. When a driver is changed, settings of presently shown
property are saved and the property of the newly selected driver will appear.
S
Set up-Original Paper
Select the original paper from the list shown by clicking the [▼] button beside [Setup] tab-[Paper]-
[Original Paper] box.
The original paper you can select is as follows:
Paper Sizes to Be Selected (US)
Paper Sizes to Be Selected (Europe/others)
A3
A3
A4
A4
A4R
A4R
A5R
A5R
B5
B4
B5R
B5
Legal (8.5x14in)
Letter (8.5x11in)
LetterR (8.5x11in)
Statement (5.5x8.5in)
B5R
B6R
8k
16k
16kR
F4
Ledger
Legal (8.5x14in)
Letter (8.5x11in)
LetterR (8.5x11in)
Statement (5.5x8.5in)
Refer to the operating manual of the copier for paper sizes which can be used on each tray.
[**R] indicates to feed paper from a short edge. Document sizes not including “R” indicate to feed
paper from a long edge.
Set up-Paper Size
When [Setup] tab-[Paper]-[Original Paper] has
been changed, [Setup] tab-[Paper]-[Paper Size]
is automatically set the same settings as
[Original Paper].
You can select other paper sizes than that
automatically set from the list shown by clicking
the [▼] button beside [Paper Size].
Paper sizes which you can select is the same as
those in the above-mentioned Paper-Original
Paper.
Refer to the operating manual of the copier for paper sizes which can be used on each tray.
[**R] indicates to feed paper from a short edge. Document sizes not including [R] indicate to feed
paper from a long edge.
IP-011 Printer Controller 3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Settings of the two-way communication function
The [Spool Settings] dialog shown by clicking
the [Details] tab-[Spool settings] button enables
you to perform settings of spooling and the bi-
directional communication function.
When [Enable bi-derectional support for this
printer] is selected, the bi-directional communi-
cation is performed.
When [Disable bi-derectional support for this
printer] is selected, the bi-directional communication is not performed.
Sharing
By using the [Sharing] tab, you can set to share
a printer. Refer to the manual of Windows for
printer sharing.
Smoothing
Set smoothing from the list shown by clicking
the [▼] button beside the [Smoothing] box of
the [Print Quality] tab.You can select Smoothing
from [Off], [Type 1], [Type 2] and [Type 3].
Default of Smoothing is [Off].
This function is unavailable for US.
[Type 1] performs processes suitable for oblique
lines of general characters and pictures. [Type 2]
performs processes suitable for curves of gen-
eral characters. [Type 3] performs processes suit-
able for curves of decorated characters and fine characters.
Sort
By using [Setup] tab-[Sorting], the method of
sorting is set. Default of [Sorting] is [Sort].
When [Sort] is selected, after one copy of all
pages has been printed, the second copy, the
third copy, .... are printed.
When [Group] is selected, first, the required
pieces of the first page are printed. Then, the
required pieces of the second page, the third
page, ..... are printed.
[Group] can be selected by using [Setup] tab-
[Sorting] when the following conditions are
satisfied.
Sort
group
• When [OHT Interleave] or [OHT Interleave
Printed] is not selected in the [Paper] tab,
• When Front/Back Cover are not set, and
• When the Staple setting is set to [Off].
3-18 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Spool settings
Set the method of spooling (temporary saving)
the print data when it is sent to the printer on
the [Spool Settings] dialog shown by clicking
[Detail] tab-[Spool Settings] button.
When [Spool print jobs so progrom finishes
printing faster] is selected, Spool is set to on.
Then, select either [Start printing after last page
is spooled] or [Start printing after first page is
spooled] as a method of spooling.
When [Start printing after last page is
spooled] is selected, it is possible to edit
other documents and start up other
applications while printing, since print data
is sent to a printer after the printing
process of applications has been com-
pleted.
When [Start printing after first page is
spooled] is selected, print data is spooled
one page by one page and sent to a printer. Although it takes more time that an application is
released from the printing process, this method is suitable in the case that free space for
spooling in your hard disk is small.
Select [Spool data format] from among EMF or RAW.
When [Print directly to the printer] is selected, a print job is directly sent to a printer without spooling
it.
You can also perform settings of the bi-directional communication function when setting spooling.
Staple
Set the position of staples from the list shown
by clicking the [▼] button beside [Setup] tab-
[Staple] box.
You can select the staple setting from [Off], [1-
Left], [1-Right], [2-Left],and [2-Top].
Default is [Off].
However, the staple setting can not be per-
formed in the following cases;
*When [None] is selected in the Finisher
settings or the Finisher is not installed,
*When [Group] is selected in the [sorting],
*When [B6R] is selected in the Paper Size,
*When [OHT Film], [OHT Interleave] or [OHT Interleave Printed] is selected in the Paper Type,
*When [Booklet] is selected in the [Duplex] , or
*The following combination is selected.
e.g. A3-size paper (portrait) and 2-Left stapling
IP-011 Printer Controller 3-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
In addition, when Staple is specified, you can not select Alternate.
You can not staple at two positions for the paper of B5R or smaller.
Stapling is performed in accordance with orientations as follows:
1- Left (portrait)
1- Right (portrait)
2-Left (portrait)
2- Top (portrait)
1- Left (landscape)
1-Right (landscape)
2-Left (landscape)
2-Top (landscape)
T
Timeout settings
By using [Detail] tab-[Timeout Settings], the
timeout value is set.
The [Not selected] box is used to set the waiting
time until a printer becomes available of printing
in the unit of second when a computer starts
outputting print data. If the waiting time exceeds
this set value, a printer error is shown and the
job is automatically cancelled.
The [Transmission retry] box is used to set the
waiting time until a printer a printer becomes available of printing in the unit of second when a
computer fails to output once and outputs print data again. If the waiting time exceeds this set
value, a printer error is shown and the job is automatically cancelled.
3-20 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
W
Watermark
Selecting a watermark from the list of the
[Watermark] tab enables you to print docu-
ments with a watermark.
When the Printer Driver is installed, the basic
watermarks are installed at the same time. In
this condition, you can select a watermark from
[NONE], [CONFIDENTIAL], [COPY], [DRAFT],
[FILE COPY], [FINAL], [PROOF] and [TOP
SECRET]. Default of watermark is [None].
On the [Edit/Add Watermark(Sub-Menu)]
dialog shown by clicking the [Add] button, you
can create up to 50 watermarks with charac-
ters a user specifies.
If the number of watermarks exceeds 50, the
[Add] button becomes disable. In addition, the
number of characters a user can specify to
create one watermark is 72 or less.
On the [Edit/Add Watermark(Sub-Menu)]
dialog shown by clicking the [Edit] button, you
can edit existing watermarks.
You can delete watermarks by selecting them from the list and clicking the [Delete] button.
When [First Page Only] is selected, you can print a watermark on the first page of documents
only.
Z
Zoom
In order to change the print size of documents, you
can select the size of print in 1% by using [Setup]
tab-[Zoom] box.
Default of Zoom is 100%.
The value can be specified from between 25% and
400%.
IP-011 Printer Controller 3-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Driver Function Combination List
Paper Tray
Paper Type
Output Tray
OHT
Auto
Select
OHT
Film
OHT
Interleaved
Printer
default
Tray 1 Tray 2 Tray 3 Tray 4 Bypass
Plain
Printed- Tray 1 Tray 2 Tray 3 Tray 4
interleaved
Paper Size
A3
҂
k
k
k
҂
k
k
k
k
҂
҂
k
k
҂
҂
҂
҂
k
k
҂
҂
҂
҂
k
k
҂
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
A4R
A4
A5R
A5
A6
҂
҂
҂
҂
B4
k
k
k
҂
k
k
k
҂
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
B5R
B5
B6R
Post Card
҂
҂
҂
Ledger (11҂17)
҂
k
҂
k
҂
Legal(8.5҂14)
k
k
k
k
҂
LetterR(8.5҂11R)
k
k
҂
k
k
҂
҂
Letter(8.5҂11)
k
҂
Half Letter(5.5҂8.5)
Paper Tray
Tray 1
Tray 2
҂
Tray 3
҂
Tray 4
҂
Bypass
k
k
Auto Select
k
k
Paper Type
Output Tray
Plain
OHT Film
OHT Interleaved
OHT Printed-interleaved
Tray 1
Tray 2
Tray 3
Tray 4
Printer default
Alternate
Sorting
Layout
On
Off
Sort
Group
1 up
2 up
4 up
8 up
9 up
Print Page Borders
Staple
On
None
Off
1-left
1-right
2-left
2-top
Duplex
1 Side
2 Sides Short Edge Binding
2 Sides Long Edge Binding
Booklet
Off
Front Cover
Back Cover
On
Printed
Non Printed
Off
On
Printed
Non Printed
Tray 1
Front/Back Cover Paper
Tray
Tray 2
Tray 3
Tray 4
Bypass
Plain
Front/Back Cover Paper
Type
Thick
Finisher
None
2 Trays
3 Trays
4 Trays
None
Option Tray
DB-209
DB-409
* When the paper size is A3, B4, B6R, Ledger(11x17in), Legal(8.5x14in) or Statement(5.5x8.5in), if the DB-409 is
selected, you can not use the Paper Tray 3.
3-22 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Staple
Print Page Borders
Alternate
On Off
Sorting
Sort
Layout
Group
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
1 up
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
2 up
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
4 up
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
8 up
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
9 up
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
On
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
None
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
Off
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
1-left 1-right 2-left 2-top
Paper Size
A3
҂
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
҂
k
k
k
k
҂
k
k
k
k
҂
A4R
A4
k
҂
A5R
A5
҂
A6
k
҂
҂
҂
҂
҂
B4
҂
҂
҂
҂
B5R
҂
k
k
҂
k
k
҂
҂
҂
B5
k
҂
҂
҂
B6R
҂
҂
Post Card
҂
҂
҂
҂
҂
Ledger (11҂17)
҂
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
҂
Legal(8.5҂14)
҂
LetterR(8.5҂11R)
҂
Letter(8.5҂11)
k
҂
Half Lettern5.5҂8.5)
Paper Tray
Tray 1
k
k
k
k
k
k
k
҂
Tray 2
Tray 3
Tray 4
Bypass
Auto Select
Paper Type
Output Tray
Plain
OHT Film
OHT Interleaved
҂
҂
҂
҂
҂
OHT Printed-interleaved
҂
҂
҂
҂
҂
҂
Tray 1
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
҂
k
k
k
k
k
҂
k
k
k
k
k
҂
Tray 2
Tray 3
Tray 4
Printer default
Alternate
Sorting
Layout
On
Off
k
k
҂
k
k
҂
k
k
҂
k
k
҂
Sort
Layout
1 up
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
2 up
k
k
k
k
4 up
8 up
9 up
Print Page Borders
Staple
On
None
Off
1-left
1-right
2-left
2-top
Duplex
1 Side
2 Sides Short Edge Binding
2 Sides Long Edge Binding
Booklet
Off
Front Cover
Back Cover
On
Printed
Non Printed
Off
On
Printed
Non Printed
Tray 1
Front/Back Cover Paper
Tray
Tray 2
Tray 3
Tray 4
Bypass
Plain
Front/Back Cover Paper
Type
Thick
Finisher
None
2 Trays
3 Trays
4 Trays
None
Option Tray
DB-209
DB-409
IP-011 Printer Controller 3-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Duplex
Front Cover
Back Cover
Front/Back Cover Paper Tray
2 Sides
Short
2 Sides
Long
Non
Printed
Non
Printed
Booklet
Printed
On
Printed
On
1 Side
Off
Off
Tray 1 Tray 2 Tray 3 Tray 4 Bypass
Edge
Edge
Binding
Binding
Paper Size
A3
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
҂
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
҂
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
҂
k
k
k
k
҂
k
k
k
k
҂
k
k
k
k
҂
k
k
k
k
҂
k
k
k
k
҂
k
k
k
k
҂
A4R
A4
A5R
A5
҂
A6
҂
҂
҂
҂
҂
҂
҂
҂
҂
҂
҂
҂
҂
҂
B4
k
k
k
҂
k
k
k
҂
k
k
k
҂
k
k
k
҂
k
k
k
҂
k
k
k
҂
k
k
k
҂
k
k
k
҂
k
k
k
҂
k
k
k
҂
k
k
k
҂
k
k
k
҂
k
k
k
҂
k
k
k
҂
B5R
B5
B6R
Post Card
҂
҂
҂
҂
҂
҂
҂
҂
҂
҂
҂
҂
҂
҂
Ledger (11҂17)
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
҂
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
҂
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
҂
Legal(8.5҂14)
LetterR(8.5҂11R)
k
k
҂
Letter(8.5҂11)
Half Lettern5.5҂8.5)
Paper Tray
Tray 1
k
k
k
k
҂
Tray 2
҂
Tray 3
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
Tray 4
k
k
k
k
k
k
k
k
k
k
k
k
҂
Bypass
k
k
k
k
k
k
k
k
k
k
k
҂
Auto Select
k
k
҂
k
k
҂
k
k
҂
k
k
k
k
k
k
k
k
k
k
҂
Paper Type
Output Tray
Plain
OHT Film
OHT Interleaved
҂
҂
҂
҂
҂
҂
҂
҂
҂
OHT Printed-interleaved
҂
҂
҂
҂
҂
҂
҂
҂
҂
Tray 1
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
҂
k
k
k
k
k
҂
k
k
k
k
k
҂
k
k
k
k
k
҂
k
k
k
k
k
҂
k
k
k
k
k
҂
Tray 2
Tray 3
Tray 4
Printer default
Alternate
Sorting
Layout
On
Off
k
k
k
҂
k
k
҂
k
k
҂
k
k
҂
k
k
҂
k
k
҂
k
k
҂
k
k
҂
k
k
҂
k
k
҂
k
k
҂
k
k
҂
Sort
Group
1 up
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
2 up
k
҂
4 up
8 up
҂
9 up
҂
Print Page Borders
Staple
On
k
k
k
҂
None
Off
1-left
1-right
҂
2-left
҂
2-top
҂
Duplex
1 Side
2 Sides Short Edge Binding
2 Sides Long Edge Binding
Booklet
Off
Front Cover
Back Cover
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
On
Printed
Non Printed
Off
On
Printed
Non Printed
Tray 1
Front/Back Cover Paper
Tray
Tray 2
Tray 3
Tray 4
Bypass
Plain
Front/Back Cover Paper
Type
Thick
Finisher
None
2 Trays
3 Trays
4 Trays
None
Option Tray
DB-209
DB-409
3-24 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Printer Driver
Front/Back Cover Paper Type
Finisher
2 Trays
Option Tray
DB-209 DB-409
Plain
k
k
k
k
҂
Thick
k
k
k
k
҂
None
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
3 Trays
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
4 Trays
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
None
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
Paper Size
A3
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
A4R
A4
A5R
A5
A6
҂
҂
B4
k
k
k
҂
k
k
k
҂
B5R
B5
B6R
Post Card
҂
҂
Ledger (11҂17)
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
҂
Legal(8.5҂14)
҂
LetterR(8.5҂11R)
҂
Letter(8.5҂11)
k
҂
Half Lettern5.5҂8.5)
Paper Tray
Tray 1
҂
Tray 2
҂
Tray 3
҂
Tray 4
҂
҂
Bypass
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
Auto Select
Paper Type
Output Tray
Plain
k
k
k
k
k
k
k
k
k
҂
OHT Film
OHT Interleaved
OHT Printed-interleaved
Tray 1
Tray 2
҂
Tray 3
҂
Tray 4
҂
Printer default
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
Alternate
Sorting
Layout
On
Off
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
҂
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
Sort
Group
1 up
2 up
4 up
8 up
9 up
Print Page Borders
Staple
On
None
Off
1-left
1-right
҂
2-left
҂
2-top
҂
Duplex
1 Side
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
2 Sides Short Edge Binding
2 Sides Long Edge Binding
Booklet
Off
Front Cover
Back Cover
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
On
Printed
Non Printed
Off
On
Printed
Non Printed
Tray 1
Front/Back Cover Paper
Tray
Tray 2
Tray 3
Tray 4
Bypass
Plain
Front/Back Cover Paper
Type
Thick
Finisher
None
2 Trays
3 Trays
4 Trays
None
Option Tray
DB-209
DB-409
IP-011 Printer Controller 3-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
■ Contents of This Chapter ............................................................ 4-2
■ About the Control Panel .............................................................. 4-3
● The Control Panel of the Copier .................................................................. 4-3
● How to Enter Settings on the LCD............................................................... 4-4
● Printer Mode Basic Screen.......................................................................... 4-5
● Printer Menu Screen.................................................................................... 4-5
● Printer Setting screen .................................................................................. 4-6
● Procedures of the Printer Setting ................................................................ 4-7
■ Configuration of Printer Setting Menu......................................... 4-9
■ Functions of the Printer Setting ................................................ 4-11
● Network Setup ........................................................................................... 4-11
● Select Language........................................................................................ 4-11
● Print Quality ............................................................................................... 4-12
● I/O Timeout ................................................................................................ 4-12
● Test Print .................................................................................................... 4-13
● CMD Error Pape ........................................................................................ 4-13
● Error Pape ................................................................................................. 4-13
● Factory Default .......................................................................................... 4-14
● Help ........................................................................................................... 4-14
IP-011 IP-011 Printer Controller 4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
■ Contents of This Chapter
In this chapter describes the printer mode basic screen and the setup menu of the Copier Operation
Panel. Refer to the operating manual of the copier for other functions and screens of the
Control Panel.
Refer to “2 Setup” (2-1 page) for how to use the Printer Driver from applications, “3 Printer Driver”
(3-1 page) for how to set the printer from the Printer Driver and “5 Status Monitor and Control Panel”
(5-1 page) for how to set the printer from the Printer Tools.
4-2 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
■ About the Control Panel
● The Control Panel of the Copier
SCANNER/PRINTER LED
[SCANNER/PRINTER] button
DATA LED
SCANNER/PRINTER
FAX
COPY
HELP
1
4
7
2
5
8
0
3
6
9
INTERRUPT
CHECK
APPLICATION
STOP/
CLEAR
OUTPUT
START
CLEAR QTY
AUTO RESET
[STOP/CLEAR] button
[AUTO RESET] button
LCD
[Setting confirmation] button
[SCANNER/PRINTER] button
Switches to the printer mode.
LCD
Displays the status of the Printer Controller, menus related to settings and options to be selected
are displayed on the LCD.
[CHECK] button
Displays the setting CHECK screen of the copier on the LCD.
[AUTO RESET] button
Resets settings of the copier to default settings.
[STOP/CLEAR] button
Cancels the currently processing copy or print process.
DATA LED
This LED flashes in green when the Print Engine is receiving data.
Not when the Print Engine is receiving data, but when data is saved in memory of the Printer
Engine, this LED is steadily lit.
SCANNER/PRINTER LED
This LED is turned on in green in the printer mode and is turned on in red when a warning
message or an error message is issued. In such a case, the print process is interrupted. Opera-
tions by an operator or a service is required. Check the error information on the LCD. When the
cause of the error is removed, the print process starts again.
IP-011 Printer Controller 4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
● How to Enter Settings on the LCD Panel
You can enter settings from the printer mode basic screen shown on the LCD by using either the item selection or
the information entry.
Item Selection
In this method, various settings are performed by selecting a button with a number which corre-
sponds to the item you would like to select on the LCD.
Information Entry
In this method, a printer name or a set value is entered by selecting alphabets or numbers shown
on buttons of the LCD.
Currently Selected Items
Currently selected items are indicated with a "+" mark.
4-4 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
● Printer Mode Basic Screen
When the Konica 7020 series +IP-011 system starts properly, the printer mode basic screen is displayed on the
LCD by pressing the [SCANNER/PRINTER] button.
● Printer Menu Screen
The following printer menu screen is displayed by pressing the [Setting] key on the printer mode
basic screen.
When the [SCANNER/PRINTER] button is pressed again, the LCD is changed to the copy mode
basic screen, and the normal copy settings becomes available.
[1. Setting]
The Printer Setting screen is displayed by pressing the [1] button. On the Printer Setting screen,
you can perform various settings related to the Printer Controller.
[2. Cancel Job]
You can cancel the print command currently being processed by pressing the [2] button.
[3. Detail Message]
Information related to the printer setting is displayed on the LCD by pressing the [3] button.
IP-011 Printer Controller 4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
● Printer Setting screen
When “1. Setting” on the printer menu screen is selected, the Printer Setting screen is displayed.
When an item is selected on the Printer Setting screen, each setting screen corresponding to the selected item is
displayed.
Buttons commonly used among setting screens are as follows:
[Main Menu]
Pressing the [Main menu] button returns to the printer menu screen.
After settings have been changed, when the [Main Menu] button is pressed, the save confirmation
screen is displayed.
[Previons]
Pressing the [Previous] button returns to the previous setting screen.
After settings have been changed, when the [Previous] button is pressed, the save confirmation
screen is displayed.
Numeric keys
In order to select an item on the screen, press a numeric key corresponding to a number of the
item you would like to select.
In addition, when you are required to enter a value, press numeric keys to enter the value.
Press the [Main Menu] or [Previous] button to show the save confirmation screen. Then, press the [Yes] button to
save the settings. Press the [No] button not to save the settings.
4-6 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
● Procedures of the Printer Setting
The following show the procedures of the printer setting by using the LCD Panel;
Press the [SCANNER/PRINTER] button to
show the printer mode basic screen.
The copy mode basic screen is switched to
the printer mode basic screen.
Press the [Setting] key to show the
printer menu screen.
Press the numeric key [1] to select
[1. Setting].
The printer mode basic screen is switched to
the printer menu screen.
Press the numeric key corresponding to a number
of the item you would like to select.
The setting screen of the selected item is
displayed.
Continue the setting by pressing the numeric key
corresponding to a number of the item you would
like to select.
Press the [Previous] button to return to the previous
setting screen.
Press the [Main Menu] button to return to the printer
menu screen.
IP-011 Printer Controller 4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
Press the [Yes] button on the save
preservation confirmation screen shown
by pressing the [Main Menu] or [Previous]
button to save new settings.
Press the [No] button not to save
the settings.
Refer to “ Configuration of the Printer Setting Menu ” (4-9 page) for configuring the printer setting menu.
Refer to “ Functions of the Printer Setting ” (4-11 page) for the printer setting details.
4-8 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
■ Configuration of Printer Setting Menu
1 Network Setup
*This menu is displayed only when the KN-304 is attached.
1 Enable DHCP
1 Set IP Mode
1 TCP/IP Setup
2 Static IP Address
2 Set IP Manually
1 IP Address
2 Subnet Mask
3 Gateway
3 LPD Banner Enable
4 Persistent IP
Address Enable
1 Server Name
2 Server Password
3 Queue Scan Rate
4 Frame Type
2 NetWare Setup
1 Yes
2 No
1 Auto
5 Disable Bindery
6 NDS Context
7 NDS Tree
2 Ethernet 802.3
3 Ethernet II
4 Ethernet SNAP
5 Ethernet 802.2
3
Password Protection
2 Select Language For US : English Only
1 English
2 French
3 Italy
4 German
5 Spanish
IP-011 Printer Controller 4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
3 Print Quality
1 Off
1 Smoothing
2 Type 1
3 Type 2
4 Type3
For US : Not available
1 Auto
2 On
2 Page Protection
4 I/O Timeout
1 5
6 60
2 10
3 15
4 20
5 30
7 120
8 180
9 240
10 300
5 Test Print
1 Demo/Configuration Page
2 NIC Configuration
6 CMD Error Page
1 Off
2 On
7 Error Page
1 Off
2 On
8 Factory Default
9 Help
4-10 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
■ Functions of the Printer Setting
● Network Setup
Select [1. Setting]-[1. Network Setup] on the Printer Setting screen to display the network setup screen. [1.
Network setup] is displayed only when the KN-304 is attached.
Items of the network setup screen are as follows: Refer to the operating manual of the KN-304 for details of the
network connection.
[1.TCP/IP Setup]
Press [1] to display the TCP/IP Setup screen. IP Address, Subnet Mask, Gateway, Enable DHCP
and Enable LPD Banner can be set on the TCP/IP Setup screen.
[2. NetWare Setup]
Press [2] to display the NetWare Setup screen. Server Name, Server Password, Queue Scan Rate,
Frame Type, Disable Bindery, NDS Context and NDS Tree can be set on the NetWare Setup
screen.
[3. Password Protection]
Press [3] to display the Password Protection screen. A password used for the network setup can be
set and changed.
● Select Language
Select [1. Setting]-[2. Select Language] on the Printer Setting screen to display the Select Language screen.
Items of the Select Language screen are as follows. The factory default is [1. English].
For US, Only English is available.
[1. English]
Press [1] to set the system language to English.
[2. French]
Press [2] to set the system language to French.
[3. Italy]
Press [3] to set the system language to Italian.
[4. German]
Press [4] to set the system language to German.
[5. Spanish]
Press [5] to set the system language to Spanish.
For US : English Only
IP-011 Printer Controller 4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
● Print Quality
Select [1. Setting]-[3. Print Quality] on the Printer Setting screen to display the Print Quality Setup screen.
Items of the Print Quality Setup screen are as follow:
[1. Smoothing]
Press [1] to display the Smoothing Setup screen.You can set to [Off], [Type 1], [Type 2] or [Type 3]
on the Smoothing Setup screen. The factory default is [1. None].
[2. Page Protection]
Press [2] to display the Page Protection Setup screen.You can set to [Auto] or [On] on the Page
Protection Setup screen. The factory default is [1. Auto].
● I/O Timeout
Select [1. Setting]-[4. I/O Timeout] on the Printer Setting screen to display the I/O Timeout Setup
screen. The factory default is [5. 30].
Items of the I/O Timeout Setup screen are as follows:
[1. 5]
Press [1] to set the I/O Timeout value to 5 seconds.
[2. 10]
Press [2] to set the I/O Timeout value to 10 seconds.
[3. 15]
Press [3] to set the I/O Timeout value to 15 seconds.
[4. 20]
Press [4] to set the I/O Timeout value to 20 seconds.
[5. 30]
Press [5] to set the I/O Timeout value to 30 seconds.
[6. 60]
Press [6] to set the I/O Timeout value to 60 seconds.
[7. 120]
Press [7] to set the I/O Timeout value to 120 seconds.
[8. 180]
Press [8] to set the I/O Timeout value to 180 seconds.
[9. 240]
Press [9] to set the I/O Timeout value to 240 seconds.
[10. 300]
Press [10] to set the I/O Timeout value to 300 seconds.
4-12 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
● Test Print
Select [1. Setting]-[5. Test Print] on the Printer Setting screen to display the Test Print Setup screen.
Items of the Test Print Setup screen are as follows:
[1. Demo/Configuration Page]
Press [1] to print the Demo/Configuration Page immediately.
Items of the Demo/Configuration Page are as follows:
• Version information (Printer Driver/Network card: only when the KN-304 is attached)
• Current settings (Engine Destination / Resolution / Print Speed / Default Paper Size / Default
Paper Tray / Finisher / Optional Paper Tray / Timeout Setting)
• Paper (Tray 1 / Tray 2 / Tray 3 / Tray 4 / Bypass Tray)
• Device status (Controller Memory / Free Memory)
• Miscellaneous (Total Page count / Printer page count)
[2. NIC Configuration Page]
Press [2] to print the NIC Configuration Page immediately. [2. NIC Configuration Page] is displayed
only when the KN-304 is attached.
Refer to the operating manual of the KN-304 for details of the NIC Configuration Page.
● CMD Error Page
Select [1. Settings]-[6. CMD Error Page] on the printer mode basic screen to display the CMD Error page Setup menu.
Items of the CMD Error page Setup menu are as follows and the factory default is [1.OFF].
[1. Off]
When [1] is selected, a CMD error page is not printed in the case that the printer command error occurs.
[2. On]
When [2] is selected, a CMD error page is automatically printed in the case that the printer command error
occurs.
● Error Page
Select [1. Settings]-[7. Error Page] on the printer mode basic screen to display the Error page Setup menu.
Items of the Error page Setup menu are as follows and the factory default is [1.OFF].
[1. Off]
When [1] is selected, an error page is not printed in the case that the I/O timeout error occurs.
[2. On]
When [2] is selected, an error page is automatically printed in the case that the I/O timeout error occurs.
IP-011 Printer Controller 4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Control Panel Setup
● Factory Default
Select [1. Setting]-[8. Factory Default] on the printer mode basic screen to return various settings to the factory default.
Items of the Factory Default are as follows:
[Language]:
[Smoothing]:
English
Off
[
Page Protection]: Auto
[I/O Timeout]:
30
*
Refer to the operating manual of the KN-304 for details of Factory Default of the Network Setup.
● Help
Select [1. Setting]-[9. Help] on the printer mode basic screen to display the help screen.
[<<][>>]
Press [<<][>>] to display the previous or the next Help screen on the LCD.
4-14 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Status Monitor and Control Panel
■ Contents of This Chapter ............................................................ 5-2
■ Status Monitor and Control Panel ............................................... 5-3
● About the Status Monitor ............................................................................. 5-3
● About the Control Panel............................................................................... 5-3
■ Working Environment .................................................................. 5-4
● Compliant OS .............................................................................................. 5-4
● Interface....................................................................................................... 5-4
■ How to Install ............................................................................. 5-4
■ How to Operate the Status Monitor............................................ 5-5
● Starting the Status Monitor .......................................................................... 5-5
● Finishing the Status Monitor ........................................................................ 5-5
● Restarting the Status Monitor ...................................................................... 5-5
● Show/Hide the Status Monitor ..................................................................... 5-6
● Display Change ........................................................................................... 5-7
■ How to Operate the Control Panel ............................................. 5-8
● Starting the Control Panel ........................................................................... 5-8
● Finishing the Control Panel.......................................................................... 5-8
● Buttons of the Control Panel........................................................................ 5-9
● Settings of Paper ....................................................................................... 5-10
● Printer Setting ............................................................................................ 5-11
● Test Print .................................................................................................... 5-12
● Confirmation of Configurations .................................................................. 5-12
IP-011 Printer Controller 5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Status Monitor and Control Panel
■ Contents of This Chapter
This chapter describes the Status Monitor and the Control Panel which are the Printer Tools. The Printer Tools is
the generic name of two programs, “Status Monitor” and “Control Panel” which are used on computers connected
to the Konica 7020 series +IP-011 system. The Printer Tools enable you to monitor the printer status and perform
printer settings from computers connected to the Konica 7020 series +IP-011 system.
Refer to “2 Setup” (2-1 page) for how to set the printer from applications, “3 Printer Driver” (3-1 Page) for how to
install the printer from the Printer Driver and “4 Control Panel Setup” (4-1 page) for how to set the printer from the
Control Panel.
5-2 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Status Monitor and Control Panel
■ Status Monitor and Control Panel
The Printer Tools is the generic name of two programs, “Status Monitor” and “Control Panel” which are used on
computers connected to the Konica 7020 series +IP-011 system.
● About the Status Monitor
The Status Monitor is a program which enables you to monitor the printer status from computers connected to the
Konica 7020 series+IP-011 system.
In the case that you set the Status Monitor to automatically start at the time of installing the Printer Tools, the
Status Monitor automatically starts and the Status Monitor icon is displayed on the task bar when a computer is
started.
The Status Monitor displays information about the printer status which has been received from the IP-011 in the
form of easy-to-understand images and messages. Additionally, in the case that any problems occur on the printer
side, the method of recovery is displayed on the Status Monitor.
Moreover, background colors of the Status Monitor icon on the task bar change in accordance with the printer
status.
• Printer is ready / Printing / Canceling printing / Setting printer: Blue
• Error: Red
• No paper, Warming up:Yellow
● About the Control Panel
The Control Panel is a program to set the printer and used on computers connected to the Konica 7020 series
+IP-011 system.
Select [Printer Setting] by clicking it on the [setup] menu of “Status Monitor” to start the Control Panel.
The Control Panel is made of the [Paper] tab, [Printer Setting] tab, [Test Print] tab and [Configurations] tab.
[Paper] tab
Sets Paper Size, Paper Tray, Output Tray, Orientation (Portrait / Landscape) and Copies.
[Printer Setting] tab
Sets Page Protection, I/O Timeout, Line/Page, Language and Smoothing.
[Test Print] tab
Prints the Print Demo/Configuration Page or the Print NIC Status Page.
[Configuration] tab
Check the setting status of the printer name, free memory, option, etc.
IP-011 Printer Controller 5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Status Monitor and Control Panel
■ Working Environment
● Compliant OS
The Status Monitor and the Control Panel can be used on the following OS.
Windows 95
Windows 98
Windows NT4.0
Windows 2000 (to be supported)
● Interface
The interface which the Status Monitor and the Control Panel use is as follows:
IEEE 1284 (Compatible mode, Nibble and ECP)
■ How to Install
When executing “setup.exe” held in the CD-ROM to install the printer driver, you can make a choice to install
Status Monitor and Control Panel simultaneously with the printer driver.
Refer to “2 Setup” (2-1 page) for installation of the Printer Driver.
5-4 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Status Monitor and Control Panel
■ How to Operate the Status Monitor
● Starting the Status Monitor
In the case that you set the Status Monitor
to automatically start at the time of
installing the Printer Tools, the Status
Monitor automatically starts when
a computer starts.
Immediately after the [Konica IP-011 Status
Monitor] window has been displayed, the
printer status is checked.
● Finishing the Status Monitor
Click [View] menu-[Finish] on the
[Konica IP-011 Status Monitor] window.
● Restarting the Status Monitor
Click [Start]-[Program]-[KONICA IP-011]-
[KONICAIP-011 Printer Tools] to
start the Status Monitor again after you
have exited from the Status Monitor.
Immediately after the [Konica IP-011 Status
Monitor] window has been displayed, the
printer status is checked.
IP-011 Printer Controller 5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Status Monitor and Control Panel
● Show/Hide the Status Monitor
When the [Close] button is clicked when
the Status Monitor is displayed, the Status
Monitor is hidden
(displayed as an icon on the task bar.).
When the Status Monitor icon on the task
bar is clicked when the Status Monitor is
hidden, the Status Monitor is displayed.
When an error occurs in communication with the printer, a confirmation message is displayed.
Click the [OK] button of the confirmation message and check the connection to the printer.
5-6 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Status Monitor and Control Panel
● Display Change
Display of the Status Monitor can be selected from either [Expand] or [Reduce]. Normally, the Status Monitor
starts in the [Reduce] display.
In the [Expand] display, when a problem related to the printer occurs and information related to the problem is
shown on the Status Monitor, the position of the problem is indicated by using an image and a method of recovery
is displayed in the How to Recover list. Switch the display of the Status Monitor if necessary.
In Case of Expanding the Display
Select [Expand] from the [View] menu.
The [Konica IP-011 Status Monitor] window is
expanded.
In Case of Reducing the Display
Select [Reduce] from the [View] menu.
The [Konica IP-011 Status Monitor] window is
reduced.
IP-011 Printer Controller 5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Status Monitor and Control Panel
■ How to Operate the Control Panel
● Starting the Control Panel
Select [Printer Setting] from the [Setup]
menu of the Status Monitor window.
The [Konica IP-011 Control Panel]
dialog is displayed.
● Finishing the Control Panel
Click the [OK] button to send data
of settings to the printer.
The [Konica IP-011 Control Panel] dialog is
closed and the [Konica IP-011 Status
Monitor] window is displayed.
Click the [Cancel] button not to
perform settings.
The [Konica IP-011 Control Panel] dialog is
closed and the [Konica IP-011 Status
Monitor] window is displayed.
5-8 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Status Monitor and Control Panel
● Buttons of the Control Panel
[OK]
When the [OK] button is clicked, data of all settings of the tab is sent to the printer. Then, the
[Konica IP-011 Control Panel] dialog is closed and the [Konica IP-011 Status Monitor] window is
displayed.
[Cancel]
[Apply]
When the [Cancel] button is clicked, the [Konica IP-011 Control Panel] dialog is closed and the
[Konica IP-011 Status Monitor] window is displayed.
When the [Apply] button is clicked, data of present settings of the tab is sent to the printer. This
button is used to continue to perform settings of other tabs.
[Set Default]
When the [Set Default] button is clicked, default settings are displayed.
[Help]
When the [Help] button is clicked, Help of the [Konica IP-011 Control Panel] dialog is displayed.
When an error occurs in communication with the printer, a confirmation message is displayed.
Click the [OK] button of the confirmation message and check the connection to the printer. Then,
perform settings on the [Konica IP-011 Control Panel] again.
IP-011 Printer Controller 5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Status Monitor and Control Panel
● Settings of Paper
Click the [Paper] tab of the [Konica IP-011 Control Panel] dialog.
The [Paper] tab of the [Konica IP-011 Control Panel] dialog is displayed.
On the list shown by clicking the [▼] button beside [Paper Size], [Paper Tray] and
[Output Tray] of the [Paper] group box, select an item you desire respectively.
Click either [Portrait] or [Landscape] from the [Orientation] group box.
Set the number of copies you desire to print by clicking the [▲] or [▼] button or directly
entering the number on the box of the [Copies] group box.
Check the settings.
Click the [OK] button when you do not continue to perform settings of other tabs.
Click the [Apply] button when you continue to perform settings of other tabs and
register settings of the [Paper] tab before moving to other tabs.
Click the desired tabs, when you continue to perform settings of other tabs.
5-10 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Status Monitor and Control Panel
● Printer Setting
Click the [Printer Setting] tab of the [Konica IP-011 Control Panel] dialog.
The [Printer Setting] tab of the [Konica IP-011 Control Panel] dialog is displayed.
Click either [Auto] or [On] of the [Page Protection] group box.
Select the desired item on the list shown by clicking the [▼] button of the [I/OTimeout]
Group Box.The printer waits for entry of data during time (second) you selected in this
box. In the case that data is not entered within the set I/OTimeout time, the printer
automatically cancels a job.
Set the number of lines you desire to print on one page in the box of the [Line/Page]
group by clicking the [▲] or [▼] button or directly entering the number.You can set the
value from between 5 and 128.
Select the desired item from the list shown by clicking the [▼] button of the [Select
Language] group box.
Click one of [Off], [Type 1], [Type 2] and [Type 3] on the [Smoothing] group box.
Confirm the settings.
Click the [OK] button when you do not continue to perform settings of other tabs.
Click the [Apply] button when you continue to perform settings of other tabs and
register settings of the [Paper] tab before moving to other tabs.
Click the desired tabs, when you continue to perform settings of other tabs.
IP-011 Printer Controller 5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Status Monitor and Control Panel
● Test Print
Click the [Test Print] tab of the [Konica IP-011 Control Panel] dialog.
The [Test Print] tab of the [Konica IP-011 Control Panel] dialog is displayed.
Click the [Print Demo/Configuration Page] button to print the Print Demo/Configuration
Page. Click the [Print NIC Status Page] button to print the Print NIC Status Page.
Click the [OK] button.
Click the [OK] button when you do not continue to perform settings of other tabs.
Click the desired tab when you continue to perform settings of other tabs.
● Confirmation of Configurations
Click the [Configurations] tab of the [Konica IP-011 Control Panel] dialog.
The [Configurations] tab of the [Konica IP-011 Control Panel] dialog is displayed.
Confirm the shown printer name, free memory and setting status.
Click the [OK] button when you do not continue to perform settings of other tabs.
Click the desired tab when you continue to perform settings of other tabs.
5-12 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A Trouble Shooting
■ Error Message ........................................................... Appendix A-2
■ Basic Troubleshooting ................................................ Appendix A-3
■ General Problems of Printing ..................................... Appendix A-3
● The “OHT Film” is not selectable.................................................. Appendix A-3
● The Printer Controller does not respond to the “Print” command.
..................................................................................................... Appendix A-3
● A message to demand a paper size which you do not use is displayed.
..................................................................................................... Appendix A-4
● You can not print the test print ..................................................... Appendix A-4
● The print setting of a job does not correspond to the result of printing.
..................................................................................................... Appendix A-5
● The “Duplex” option is not displayed. ........................................... Appendix A-5
● Memory Error / Memory Overflow / Overrun ............................... Appendix A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A Troubleshooting
■ Error Message
The error messages shown on the Status Monitor are as follows:
Error Message
How to Recover
Mishandled paper in ADU
DB Upper Tray is not ready
DB Lower Tray is not ready
Mishandled paper in DB Lower Tray
No paper in DB Lower Tray
DB Lower Tray is not available
No paper in DB Upper Tray
DB Upper Tray is not available
DB door is open
Please remove paper according to the message screen of printer
Please insert DB Upper Tray
Please insert DB Lower Tray
Please remove paper according to the message screen of printer
Please load paper in DB Lower Tray
Please confirm the printer setting
Please load paper in DB Upper Tray
Please confirm the printer setting
Please close DB door
LCT is not ready
Please insert LCT
Mishandled paper in LCT
No paper in LCT
Please remove paper according to the message screen of printer
Please load paper in LCT
LCT is not available
Please confirm the printer setting
Mishandled paper in RADF
RADF Failure
Please remove original according to the message screen of the printer
Please dispose the trouble according to the message screen of the printer
Please dispose the trouble according to the message screen of the printer
Please dispose the trouble according to the User Reference Guide.
Please dispose the trouble according to the message screen of the printer
Please dispose the trouble according to the message screen of the printer
Please close Finisher Front door
RADF Communication Error
OverRun
System Failure
System Communication Error
Finisher Front door is open
Stapler cartridge is not loaded
There are no staples
Please confirm the stapler cartrigde
Please replace staple cartridge
No Toner
Please add toner
Low Toner
Please add toner
Toner bottle does not exist
NIC I/F Error
Please install the Toner bottle
Please dispose the trouble according to the User Reference Guide.
Please remove paper according to the message screen of printer
Please close Finisher Conveyance Door
Mishandled paper in Finisher
Finisher conveyance door is open
Finisher does not work correctly
Mishandled paper in Finisher
Printing Paused due to some interuptions.
Printer Controller NVRAM Error
Printer Controller SIMM Error
Printer Controller Memory Error
Printer Memory OverFlow
Printing Paused Due to No Paper
Main Lower Tray is not ready
No paper in DB Lower Tray
DB Lower Tray is not available
Optics Failure
Please dispose the trouble according to the message screen of the printer
Please remove paper according to the message screen of printer
Please wait. If this situation continues, please check printer.
Please dispose the trouble according to the User Reference Guide.
Please dispose the trouble according to the User Reference Guide.
Please dispose the trouble according to the User Reference Guide.
Please dispose the trouble according to the User Reference Guide.
Please load paper
Please insert Main Lower tray
Please load paper in DB Lower Tray
Please confirm the printer setting
Please dispose the trouble according to the message screen of the printer
Please dispose the trouble according to the message screen of the printer
Please remove paper according to the message screen of printer
Please open Bypass tray
Optics Communication Error
Mishandled paper
Bypass Tray is not ready
No paper in Bypass Tray
Bypass Tray is not available
Main Upper Tray is not ready
No paper in Main Upper Tray
Main Upper Tray is not available
Side door is open
Please load paper in Bypass tray
Please confirm the printer setting
Please insert Main Upper tray
Please load paper in Main Upper Tray
Please confirm the printer setting
Please close Side door
PM required
Please call service for PM
Printing Paused due to the limit of Fixing-unit-counter
Density declines
Please replace the Fixing unit
Please solve the trouble according to the User Reference Guide.
Remove copies from the Output Tray 1
Output Tray 1 is overloaded
Output Tray 2 is overloaded
Output Tray 3 is overloaded
Output Tray 4 is overloaded
Exit Tray is overloaded
Remove copies from the Output Tray 2
Remove copies from the Output Tray 3
Remove copies from the Output Tray 4
Remove copies from the Exit Tray
Printer Failure
Please dispose the trouble according to the message screen of the printer
Please dispose the trouble according to the message screen of the printer
Please confirm the paper
Printer Communication Error
Actual paper size is different from setting
Appendix A-2 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Basic Troubleshooting
This section describes how to troubleshoot. If troubles are not removed by using the following countermeasures,
contact a service provider.
There are some basic conditions which cause various abnormalities. Before taking a trouble as a special case,
first refer to the following basic countermeasures.
Check the power of the copier and computers and cable connections.
Check the LCD of the copier to find information concerning the current trouble.
If possible, print the “Test Print” to check that the settings are appropriate.
Check the current status of the Printer Controller.
Check the current status shown on the LCD of the Operation Panel.
Press the [SCANNER/PRINTER] button and press [3. Detail Message] of the printer mode basic
screen to check the job status.
Additionally, check the Status Monitor.You can find if the Printer Controller is processing your
job or not on the status message. When your job is not displayed on the status message, it is
considered that the Printer Controller has already finished printing your job.
When your job is being processed or waiting for being printed, the current status is displayed
on the dialog shown by double-clicking [Start]-[Settings]-[Printers]-[KONICA IP-011].
■ General Problems of Printing
● The “OHT Film” is not selectable.
Select a bypass tray with which OHT can be used.
● The Printer Controller does not respond to the “Print” command.
Check that [KONICA IP-011] is selected as a current printer.
It is required to select [KONICA IP-011] as a present printer on Windows before printing.
Check that the power switch of the copier is turned on.
Print the “Test Print”.
When you can not print a job from a computer even though you can print a test print, contact a
system administrator or a service provider.
IP-011 Printer Controller Appendix A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A Troubleshooting
● A message to demand a paper size which you do not use is displayed.
Cancel the job to change the paper size of “Page (Paper) Setup” dialog on an applica-
tion.
● You can not print the test print
Check the LCD of the copier Control Panel.
When “Ready to copy” is displayed on the LCD, go to the Step 3.
When a diagnosis message or an error message is displayed on the LCD, refer to the operat-
ing manual of the copier.
When the LCD is blank, go to the Step 2.
Press the sub power sw on the Control Panel.
When the copier is used in the Power Save mode, press this switch to show the LCD in the
Display mode.
Try to make a copy
When copy is available, go to the Step 4.
Turn off the copier and restart it. Print the test print again after the Printer Controller is
ready.
Contact a service provider when you can not print the test print after taking the above-
mentioned procedures.
Appendix A-4 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
● The print setting of a job does not correspond to the result of printing.
Check that the printer setting is not changed.
Refer to “5 Status Monitor and Control Panel” Printer Setting “(5-11 page) or ”3 Printer Driver “
Printer Driver Function List” for the printer setting.(3-5 page)
● The “Duplex” option is not displayed.
Check that , [B6R] is not selected as a paper size.
● Memory Error / Memory Overflow / Overrun
Set the Page Protection.
Refer to “3 Printer Driver ■ Printer Driver Function List” (3-5 page) or “4 Control Panel Setup
● Print Quality” (4-11 page) for the page protection.
Expand memory.
Memory of the IP-011 can be expanded up to 80 MB. Contact a service provider for details of
the memory expansion.
IP-011 Printer Controller Appendix A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B Product Specifications
■ Product Specifications ............................................... Appendix B-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B Product Specifications
■ Product Specifications
Model:
built in the Konica 7020 series Copier
Paper
You can select from the following paper sizes:
Paper Sizes to Be Selected (US)
Paper Sizes to Be Selected (Europe/others)
A3
A3
A4
A4
A4R
A4R
A5R
A5R
B5
B4
B5R
B5
Legal (8.5x14in)
Letter (8.5x11in)
LetterR (8.5x11in)
Statement (5.5x8.5in)
B5R
B6R
8k
16k
16kR
F4
Ledger
Legal (8.5x14in)
Letter (8.5x11in)
LetterR (8.5x11in)
Statement (5.5x8.5in)
Paper Feeding and Amount of Feeding Paper: The same as the copier
Load Output Paper:
Mode:
The same as the copier
The dual operation of the Copier and
the Printer is available.
(5 jobs can be processed at the maximum.)
Special Printing:
Duplex, Paper Type selection, Output Tray selection,
Print Quality mode selection, Alternate, Staple function,
Front/Back Cover function and Version display etc.
Orientation:
Portrait and Landscape.
Resolution:
600dpi
Gradation:
1 bit
No. of Print:
1 to 999
Printable Area:
Warm-up:
Head Margin: 2.5 mm, Foot Margin: 4 mm and Right and Left Margins: 1 mm
the same as the copier
Basic Configuration
Control Board
CPU:
PowerPC 401GF
Program Memory:
System Memory:
FLASH ROM
16 MB SD-RAM (Standard),
Expandable up to 80 MB (Option:MU-403/404)
Parallel port
Interface:
Centronics (IEEE 1284) / amphenol 36 pin male connector
Appendix B-2 IP-011 Printer Controllerg
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B Product Specifications
Network Interface (Option):
KN304: Ethernet (100Base-T / 10Base-T)
Protocol: IPX/SPX (NetWare)
LPD/LPR (TCP/IP)
Peer to Peer (TCP/IP)
Compliant OS:
Windows 95/98
Windows NT4.0
Windows 2000(to be supported)
Printer Language:
Destiny WinStylerNozomi Version 2.0
Printer Driver:
Printer Driver for Windows 95/98
Printer Driver for Windows NT
Compliant Host Computer:
A Windows-based computer
Compliant Finisher:
FS-107
Compliant DB:
DB-209 and DB-409
Dimension:
Weight:
240 mm (W) * 160 mm (H) * 37 mm (D)
Approx. 1.1 kg
Power:
AC 100V 50/60 Hz (maximum)
(when using 16 MB SD-RAM and KN-304)
Working Environment:
Humidity:
Temperature: 5 degree C to 55 degree C
5 % to 95 %RH (non-condensing)
Restrictive Conditions
• In the Printer mode, the EKC (Electric Key Counter) of the Konica 7020 series is not available.
• Although the Weekly Timer function of the Konica 7020 series is available in the Printer mode,
the power is not turned Off until the data output is finished when print data remains in the E-RDH .
Notice: Specifications are subject to change for improvements without notice.
IP-011 Printer Controller Appendix B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
index
index ........................................................................................ index-2
Download from Www.Somanuals.com. All Manuals Search And Download.
index
index
Front/Back Cover- Paper Tray ...................... 3-13
A
Front/Back Cover-Paper Type ...................... 3-13
About.............................................................. 3-8
Add Port ......................................................... 3-8
Allocate a printer port..................................... 3-8
Alternate......................................................... 3-9
G
[General] tab .................................................. 3-4
Group ........................................................... 3-13
B
H
Back cover...................................................... 3-9
Basic Troubleshooting ....................Appendix A-3
Booklet ......................................................... 3-11
Buttons of the Control Panel .......................... 5-9
Help.................................................... 4-10, 4-13
How to Enter Settings on the LCD ................. 4-4
How to Use Memory ...................................... 1-6
I
C
I/O Interface ................................................... 1-4
I/O Timeout......................................... 4-10, 4-12
Installation of the Printer Driver...................... 2-3
IP-011 Hardware Configuration...................... 1-4
[Color Management] tab................................. 3-3
[Configuration] tab .......................................... 5-3
Confirmation................................................. 5-12
Control Panel ......................................... 4-3, 5-3
Control Panel are install ................................. 5-4
Copy Mode ..................................................... 1-3
L
Language ....................................................... 4-9
LCD ................................................................ 4-3
D
M
Data Flow ....................................................... 1-5
DB-209 ......................................................... 3-10
DB-409 ......................................................... 3-10
Demo/Configuration Page .................. 4-10, 4-13
[Detail] tab ...................................................... 3-4
Display of the Status Monitor ......................... 5-7
Drawer Base ................................................ 3-10
Driver used for printing ................................. 3-11
[Main] ............................................................. 4-6
Memory Error .................................Appendix A-5
Memory Overrun ............................Appendix A-5
Memory Upgrading......................................... 1-6
N
Network Setup...................................... 4-9, 4-11
New Driver ................................................... 3-13
NIC Configuration............................... 4-10, 4-13
Numeric keys ................................................. 4-6
E
E-RDH ............................................................ 1-3
End Capture ................................................. 3-12
Error Message................................Appendix A-2
O
[Option] tab........................................... 2-16, 3-4
Outline of the Printer Controller ..................... 1-3
Output tray ................................................... 3-14
Overrun ..........................................Appendix A-5
F
Factory Default ................................... 4-10, 4-13
Files to be Installed ........................................ 2-3
Finisher ........................................................ 3-12
Finishing the Control Panel ............................ 5-8
Finishing the Status Monitor........................... 5-5
Front Cover .................................................. 3-12
P
Page Protection.................................. 4-10, 4-12
Paper type .................................................... 3-15
index-2 IP-011 Printer Controller
Download from Www.Somanuals.com. All Manuals Search And Download.
index
Paper-Original Paper.................................... 3-16
Port settings ................................................. 3-16
Print page borders ....................................... 3-16
Print Quality ....................................... 4-10, 4-12
Print quality .................................................. 3-16
[Print Quality] tab ................................. 2-16, 3-4
Printer Driver Function List............................. 3-5
Printer Engine ................................................ 1-3
Printer Menu Screen ...................................... 4-5
Printer Mode .................................................. 1-3
Printer Setting screen .................................... 4-6
[Printer Setting] tab ........................................ 5-3
Printing port.................................................. 3-17
Procedures of the Printer Setting ................... 4-7
Property of Printer Driver ............................... 3-3
U
Uninstaller .................................................... 2-10
W
[Water Mark] tab................................... 2-17, 3-4
R
[Reset] button ................................................. 4-3
Restarting the Status Monitor ........................ 5-5
[Return] .......................................................... 4-6
S
[Scanner/Printer] button ................................. 4-3
Select Language .......................................... 4-11
Selection of orientation ................................ 3-17
[Setting Confirmation] button.......................... 4-3
[Setup] tab .................................................... 2-13
[Share] tab...................................................... 3-4
Sharing......................................................... 3-18
Show/Hide the Status Monitor........................ 5-6
Smoothing .......................................... 4-10, 4-12
Sort .............................................................. 3-18
Staple ........................................................... 3-19
Starting the Control Panel .............................. 5-8
Starting the Status Monitor ............................ 5-5
Status Monitor ................................................ 5-3
Status Monitor install...................................... 5-4
Status Monitor working environment .............. 5-4
[Stop/Clear] button ......................................... 4-3
T
T-1 ................................................................ 3-22
Test Print ............................................ 4-10, 4-13
[Test Print] tab ...................................... 5-3, 5-12
Timeout settings........................................... 3-20
IP-011 Printer Controller index-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAUFACTURER
KONICA CORPORATION
TOKYO JAPAN
1
2000. 1
Download from Www.Somanuals.com. All Manuals Search And Download.
|