KODAK EKTAGRAPHIC III
AFT Projector
PRODUCT DESCRIPTION
Congratulations on the purchase of your KODAK EKTAGRAPHIC III AFT Projector.
Please review this product sheet and the important maintenance instructions enclosed.
The KODAK EKTAGRAPHIC III AFT Projector is a standard KODAK EKTAGRAPHIC III
A Projector with fade and timer controls added. This projector was specifically designed
for cinema applications and therefore does not include a slide tray, lamp, lens, user manual, or
remote control.
FADE and VIEW controls
There are three controls for the special features of the AFT Projector. They are located under
the projector handle.
1. Automatic AFT mode (ON / OFF)
When this switch is ON ( I ), slides will advance automatically using the VIEW and
FADE times selected.
2. VIEW adjustment screw
Allows you to select the amount of time the slide is displayed on the screen, from
5 to 15 seconds.
3. FADE adjustment screw
Allows selection of the time it takes to fade up and down between slides, from 0.5
to 4 seconds.
NOTE: The operation will sequence as follows: fade up, change slide, fade down.
Selection of 0.5 second, for example, will fade up 0.5 seconds, change slide
1 second and fade down 0.5 seconds for a total of 2 seconds per slide change.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
PROBLEM
CAUSE
CORRECTION
Projector does not operate
No power to projector
Plug power cord into suitable
electrical outlet. Set power switch
to LAMP.
No illumination on screen with
slide in projector gate
Power switch on Off or Fan
Lamp burned out
Set switch to LAMP.
Install new lamp or lamp module.
Lamp not sealed in socket
Slide itself not sharp
Check lamp.
Slide not in proper focus on
screen
Examine slide for proper focus.
First slide in tray not properly
focused
Focus center of first slide manually.
Focus manually.
Slide in different type of mount
from others
Be sure the lens gear teeth on the
lens barrel line up with the notch on
the projector.
Projection lens installed improperly
Uneven edge-to-edge focus
Slide itself is not sharp
Examine slide.
Curved-field lens used with glass,
plastic, or non-embossed mounts
Try a flat-field lens.
Curved field lens used for rear
projection
Use a flat-field lens.
Turn off autofocus.
Autofocus motor runs
continuously
Multi-aperture slides or matte-
surface write-on slides in tray
Slide fails to drop into projection
position
Tray base plate not properly
indexed
Rotate the tray base plate until it
locks into position.
Tray not properly positioned on
projector
Reposition tray on projector.
Slide mount warped or frayed at
corners
Straighten mount or remount slide.
Projector not level or tilted too high
Projection lamp not fully seated
Set projector on a stand equal with
center of screen.
Uneven illumination on screen
Check lamp.
Condenser lens not installed or not
positioned properly in mount
Check condenser lens.
Slide mount not seated properly in
projector gate
Check slide position and slide-
mount condition.
Projector won’t cycle to next slide
Tray not properly positioned
Reposition tray.
Slide or foreign object stuck in gate Remove foreign object from gate.
Program does not start with the
correct slide
Tray number is not aligned with the Reposition tray.
raised index mark.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Kodak warrants this KODAK EKTAGRAPHIC Slide Projector to function properly for four
years from the date of purchase.
If this KODAK EKTAGRAPHIC Slide Projector does not function properly within the
warranty period, upon submission of dated proof of purchase, Kodak will repair it without
charge, except for worn-out projector lamps. If Kodak is unable to repair the projector,
the option of replacement or refund of the purchase price will be available.
See an audiovisual products dealer for the KODAK EKTAGRAPHIC III AFT Slide
projector’s warranty coverage.
Limitations
This warranty does not cover circumstances beyond Kodak’s control, projector lamps, or
problems caused by failure to follow the care and operating instructions in the manual.
Any modification to the original design of this projector nullifies this warranty.
Warranty service will not be provided without dated proof of purchase.
Kodak makes on other express warranty for this product. Repair or replacement
is Kodak’s only obligation. Kodak will not be responsible for any consequential or
incidental damages resulting from the sale or use of this projector, regardless of
the cause of such damages.
Your Rights Under State Law
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights that vary from state to
state.
How To Obtain Service Assistance
To obtain service or assistance in using your KODAK EKTAGRAPHIC Slide Projector,
see an audiovisual products dealer in your area. If one is not available, call the Kodak
Information Center at 1-800-242-2424, Monday through Friday, 8 a.m. to 7 p.m. Eastern
time. In Canada, call 1-800-465-6325, Monday through Friday, 8:30 a.m. to 5 p.m.
Eastern time. Or call Kodak in your country.
Kodak and Ektagraphic are trademarks.
New 2/98. Minor revision 7/99
Printed in U.S.A.
Part No. 2H2270
Download from Www.Somanuals.com. All Manuals Search And Download.
|