Kodak Gen 5 GRD, GRD7, GRDM & GR7M Film
Technical Information Instruction Sheet – TI2375
August 2006
Features / Customer Product Specifications
Kodak Gen 5 films are fast, high contrast, broad band red-sensitive film. Their sharp dots are capable of
high resolution at fine screen rulings. These films are optimized for exposure on film recorders that use a
helium-neon laser (633 nm) or a red laser diode (630 to 670 nm) as the exposing source.
These films feature high processing speeds (development in as little as 20 seconds) and low
replenishment rates in rapid-access developer and fixer, which contribute to improved productivity and
reduced operating costs.
Gen 5 films are coated on a dimensionally stable Estar base with antistatic and surface properties to
ensure dependable transport and handling behavior.
Safelight Recommendations
Use an EncapSulite T20/ND.75 safelight or equivalent. Keep the film at least 1.2 metres (4 feet) from
the safelight. Do not expose the film to safelight illumination for longer than two minutes.
European office:
US office:
EncapSulite International Ltd.
Auf dem Loor 14a
EncapSulite International Inc.
1220 Bamore Road
51143 Köln Germany
Phone: 49 (0)2203-8 37 37
Rosenberg, TX 77471
Phone: 1-281-239-0225
Storage
Keep unexposed film and processed film in a cool, dry place, preferable at a temperature of 70° F (21° C)
or lower and 50% RH. Process film as soon as possible after exposure.
Exposure
These films are intended for use on film recorders that use a 633 nm helium-neon (HN) laser
or a 630 to 670 nm red laser diode (RLd) as the exposing source. Follow the exposure
procedures recommended by the equipment manufacturer.
Download from Www.Somanuals.com. All Manuals Search And Download.
Kodak Gen 5 GRD, GRD7, GRDM & GR7M Film
Technical Information Data Sheet – TI2375
August 2006
1. Support
Dimensionally Stable Support
GRD, GRDM
GRD7, GR7M
4 mil (0.004 in., 0.10mm)
7 mil (0.007 in., 0.18mm)
Estar base
Estar thick base
2. Dimensional Stability
Dimensional stability is an all-inclusive term. In photography, it applies to size changes caused by
changes in humidity and in temperature, and by processing and aging. The dimensional properties of The
Estar base may vary slightly in different directions within a sheet; the differences that may exist, however,
are not always aligned with the length and width directions:
Data for the 4-mil products (GRD, GRDM):
Thermal Coefficient of Linear Expansion
Unprocessed or Processed
0.001% per ° F (0.0018% per ° C)
Humidity Coefficient of Linear Expansion
Unprocessed
Processed
0.0017% per % RH
0.0016% per % RH
Processing Dimensional Change
Dependent on drying conditions
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Reciprocity
With recommended processing, the reciprocity speed change is negligible within exposure range of
1/1000 second to 1 billionth second; there is no change in contrast.
4. Graphs1
Using Kodak RA 2000 developer and replenisher (1:2)
Characteristic
A. (10-98)
B. (12-98)
Spectral Sensitivity
C. (10-98)
1 NOTICE: While the data presented are typical of production coatings, they do not represent standards
that must be met by Kodak. Varying storage, exposure, and processing conditions will affect results. The
company reserves the right to change and improve product characteristics at any time.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
© Kodak, 2006. Kodak and Gen 5 are trademarks of Kodak.
Download from Www.Somanuals.com. All Manuals Search And Download.
|