®
30" Freestanding and Slide-In Electric Range
PRODUCT MODEL NUMBERS
OVERALL DIMENSIONS
KERS807S
KESK901S
KESS907S
KESS908S
Freestanding Range
Slide-in Range
B
A
Electrical: This range is manufactured
with the neutral terminal connected to the
cabinet. Use a 3-wire UL listed, 40- or 50-
amp power supply cord (pigtail). If local
codes do not permit ground through the
neutral, use a 4-wire power supply cord
rated at 250 volts, 40 or 50 amps and
investigated for use with ranges.The range
can be connected directly to the fused
disconnect (or circuit breaker box)
A
F
B*
D*
C
C
G
through flexible or nonmetallic sheathed,
copper or aluminum cable. A UL listed
conduit connector must be provided at
each end of the power supply cable (at the
range and at the junction box). Wire sizes
and connections must conform with the
rating of the range. A time-delay fuse or
circuit breaker is recommended.
E**
D
E
F**
A. 5³⁄₄" (14.6 cm)
B. 30" (76.2 cm)
E. 30" (76.2 cm)
A. 30¹¹⁄₁₆" (77.6 cm)
D
30" (76.2 cm)
F. 27¹⁄₄" (69.2 cm) max. from
handle to standoff at back of
range**
G. Model/serial number plate
(located on the right-hand side
oven door trim)
B. 35⁵⁄₈" (90.5 cm) height to
underside of cooktop edge
with leveling legs screwed all
the way in*
C. Model/serial number plate
(located on the right-hand side
oven door trim)
E. 27¼" (69.2 cm) from handle
to standoff at back of
range**
F. 23" (58.4 cm) countertop
notch to rear of cooktop
C. 41³⁄₄" (106 cm) overall
height with leveling legs
screwed all the way in
D. 36" (91.4 cm) cooktop trim
height with leveling legs
screwed all the way in*
*Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.
*Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.
**When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm)
countertop; front of oven door protrudes 1³⁄₄" (4.4 cm) beyond
24" (61 cm) base cabinet.
**When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm)
countertop; front of oven door protrudes 1" (2.5 cm) beyond
24" (61 cm) base cabinet.
SLIDE-IN RANGE
COUNTERTOP PREPARATION
CABINET OPENING DIMENSIONS
The cooktop sides of the slide-in range fit over the
cutout edge of your countertop.
Freestanding Range
Cabinet opening dimensions shown are for
25” (64 cm) countertop depth, 24” (61 cm)
base cabinet depth and 36” (91.4 cm)
countertop height.
If you have a square finish (flat) countertop and the
opening width is 30" (76.2 cm), no countertop
preparation is required.
13" (33 cm)
upper cabinet
depth
For minimum
clearance to the
top of the cooktop,
see NOTE*.
Formed front-edged countertops: Must have
molded edge shaved flat 3/8" (1.0 cm) from each
front corner of opening.
30" (76.2 cm) min.
opening width
Slide-in Range
Tile countertops may need trim cut back
3/8" (1.0 cm) from each front corner and/or
rounded edge flattened.
30"
13" (33 cm)
(76.2 cm) min.
opening width
For minimum
clearance to the
top of the cooktop,
see NOTE*.
upper cabinet
depth
If countertop opening width is greater than 30"
(76.2 cm), adjust the 3/8" (1.0 cm) dimension.
30" (76.2 cm) min.
opening width
Countertop must be level. Place level on
countertop, first side to side; then front to back. If
countertop is not level, range will not be level.
Range must be level for satisfactory baking
performance.
22 3/4" (57.8 cm)
opening depth
1/4"
(6.2 cm) radius
both corners
Cabinet door
or hinge
should not
extend into
the cutout.
30"
Junction box - 8"
(76.2 cm) min.
opening width
(20.3 cm) to 22" (55.9 cm)
from either cabinet, 7"
(17.8 cm) max. from floor
30"
(76.2 cm)
³⁄₈"
(1.0 cm)
Cabinet door
or hinge
30 ³⁄₄"
(78.1 cm)
Junction box - 8"
should not
extend into
the cutout.
(20.3 cm) to 22" (55.9 cm)
from either cabinet, 7"
(17.8 cm) max. from floor
NOTE: 24" (61 cm) min. when bottom of wood or metal
cabinet is protected by not less than 1/4" (0.64 cm)
flame retardant millboard covered with not less than
No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel,
0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) min. clearance between the top of the
cooking platform and the bottom of an unprotected wood
or metal cabinet.
If installing a range hood or microwave hood
combination above the range, follow the range hood or
microwave hood combination installation instructions for
dimensional clearances above the cooktop surface.
Because Whirlpool Corporation policy includes a continuous commitment to improve our
products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
WI0118260
09-05-07
Download from Www.Somanuals.com. All Manuals Search And Download.
|