MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
This product is suitable for use above electric or gas cooking products up to and including 36" (91.4 cm) wide. For gas cooktop, we
recommend that the combined cooking surface rating does not exceed 55,000 BTU/hr. See “Installation Requirements” section for
further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in
these installation instructions.
Table of Contents
MICROWAVE HOOD COMBINATION SAFETY .............................. 1
INSTALLATION REQUIREMENTS ................................................... 2
Tools and Parts............................................................................... 2
Location Requirements................................................................... 2
Product Dimensions ....................................................................... 3
Electrical Requirements.................................................................. 3
INSTALLATION INSTRUCTIONS ..................................................... 4
Remove Mounting Plate ................................................................. 4
Convert Microwave Oven to External Venting ............................... 4
Locate Wall Stud(s)......................................................................... 6
Mark Rear Wall................................................................................ 7
Drill Holes in Rear Wall.................................................................... 7
Attach Mounting Plate to Wall........................................................ 8
Prepare Upper Cabinet................................................................... 8
Install the Microwave Oven ............................................................ 9
Complete Installation.................................................................... 10
VENTING DESIGN SPECIFICATIONS............................................ 11
ASSISTANCE ................................................................................... 12
Replacement Parts ....................................................................... 12
MICROWAVE HOOD COMBINATION SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
DANGER
You can be killed or seriously injured if you don't
instructions.
follow
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
W10189719A
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Dimensions
NOTE: The grounded 3 prong outlet must be inside the upper
cabinet. See “Electrical Requirements” section.
Electrical Requirements
A
B
WARNING
36"
(91.4 cm)
min.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
12" (30.5 cm) min.
13" (33.0 cm) max.
33" (83.2 cm)
typical*
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
69" (175.3 cm) min.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Observe all governing codes and ordinances.
Required:
■
A 120 Volt, 60 Hz, AC only, 15- or 20-amp electrical supply
with a fuse or circuit breaker.
Recommended:
■
A time-delay fuse or time-delay circuit breaker.
■
A separate circuit serving only this microwave oven.
GROUNDING INSTRUCTIONS
■
A. 2" x 4" wall stud
B. Grounded 3 prong outlet
For all cord connected appliances:
The microwave oven must be grounded. In the event of
an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed
and grounded.
*33" (83.2 cm) is typical for 69" (175.3 cm) installation height.
Exact dimension may vary depending on type of range/cooktop
below.
Product Dimensions
WARNING: Improper use of the grounding plug can
result in a risk of electric shock. Consult a qualified
electrician or serviceman if the grounding instructions are
not completely understood, or if doubt exists as to whether
the microwave oven is properly grounded.
"
¹⁄₄
18
(46.4 cm)
35
⁷⁄₈
" (91.1 cm)
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the microwave oven.
15 ¹⁄₂"
(39.4 cm)
18 ¹⁄₄"
(46.4 cm)
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Remove Mounting Plate
Convert Microwave Oven to
External Venting
NOTE: To avoid possible damage to the work surface, cover the
work surface.
(for wall or roof venting only)
1. Remove any remaining contents from the microwave oven
The microwave oven is set for recirculation installation. For wall or
roof venting, changes must be made to the venting system. See
“Venting Design Specifications” section.
NOTE: Skip this section if you are using recirculation installation.
Keep the damper assembly in case the venting method is
changed, or the microwave oven is reinstalled in another location
where wall or roof venting may be used.
cavity.
2. Remove the mounting plate by peeling off the strips of tape
that attach it to the back of the microwave oven, and set the
mounting plate aside.
To prepare the microwave oven for wall or roof venting, the vent
deflector (L-shaped metal bar) must be installed, and the
appropriate damper vent opening must be uncovered.
To Install Vent Deflector:
1. Gently pull the rings and lift vent screen from the top of the
microwave oven.
A
A
B
C
A. Mounting plate
B. Back of microwave oven
C. Tape (multiple locations)
B
C
3. Tape the microwave oven door closed so that door does not
A. Top of microwave oven
B. Vent screen
swing open while the microwave oven is being handled.
NOTE: To avoid damage to the microwave oven, do not grip or
use the door or door handle while the microwave oven is being
handled.
C. Rings
2. With vent deflector oriented as shown (wide side down), slide
it back and under the back edge of the vent opening.
A
B
A. Vent opening
B. Vent deflector
3. When the vent deflector is as far back as it can easily slide, flip
it so that the wide side is to the back of the microwave oven,
and the narrow side (with holes) is down. The vent deflector
4
Download from Www.Somanuals.com. All Manuals Search And Download.
holes should align with mounting holes in the vent opening, as
shown in inset.
3. Save the cover for possible change of venting method in the
future.
4. Position the damper assembly so that the long tab slides into
the slot on the right side of the damper vent opening, as
shown. Then secure with mounting screw.
A
B
C
A
B
A. Mounting screw
B. Damper assembly
C. Long tab (inside slot)
A. Vent opening
B. Vent deflector
Roof Venting Installation Only
To Remove Roof Damper Vent Cover:
4. Secure vent deflector with 2 mounting screws (1 on each end).
1. Locate the roof damper vent cover on the top of the
A
B
microwave oven.
2. Using diagonal wire cutting pliers, gently snip out the damper
vent cover at the perforations.
A
B
C
D
A. Mounting screw
B. Vent deflector
A. Diagonal wire cutting pliers
B. Top of microwave oven
C. Roof damper vent cover
D. Perforations
5. Replace vent screen.
Wall Venting Installation Only
3. Save the cover for possible change of venting method in the
future.
To Remove Wall Damper Vent Cover:
NOTE: Do not install damper assembly at this time.
1. Locate the wall damper vent cover on the back of the
microwave oven.
2. Using diagonal wire cutting pliers, gently snip out the damper
vent cover at the perforations.
A
B
C
D
A. Diagonal wire cutting pliers
B. Back of microwave oven
C. Wall damper vent cover
D. Perforations
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Locate Wall Stud(s)
NOTE: If no wall studs exist within the cabinet opening, do not
install the microwave oven.
1. Using a stud finder, locate the edges of the wall stud(s) within
the opening.
See illustrations in “Possible Wall Stud Configurations.”
2. Mark the center of each stud, and draw a plumb line down
each stud center. See illustrations in “Possible Wall Stud
Configurations.”
Possible Wall Stud Configurations
These depictions show examples of preferred installation configurations with the mounting plate.
No Wall Studs at Corner Holes
Figure 1
No Wall Studs at Corner Holes
Figure 2
B
C
C
D
C
D
B
A
A
A
E
A
E
E
F
E
F
NOTE: If wall stud is within 6" (15.2 cm) of the vertical
centerline (see “Mark Rear Wall” section), only recirculation or
roof venting installation can be done.
Wall Stud at One Corner Hole
Figure 3
Wall Studs at Both Corner Holes
Figure 4
D
B
B
A,D
A
E
A,D A,D
E
C
E
C
E
C
F
C
F
A. Corner holes (on mounting plate)
B. Cabinet opening vertical centerline
C. Wall stud centerlines
D. Holes for lag screws
E. Support tabs
F. Mounting plate center markers
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall Venting Installation Only
Mark Rear Wall
The microwave oven must be installed on a minimum of 1 wall
stud, preferably 2, using a minimum of 1 lag screw, preferably 2.
Centerline
Upper cabinet bottom
1. Using measuring tape, find and clearly mark the vertical
centerline of the opening.
³⁄₈" (1 cm)
4" (10.2 cm)
6" (15.2 cm)
A
6" (15.2 cm)
A. Centerline
6. Mark the centerline 3/8" (1 cm) down from the bottom edge of
2. With the support tabs facing forward (see illustrations in
“Possible Wall Stud Configurations” in “Locate Wall Stud(s)”
section), align the mounting plate center markers to the
centerline on the wall, making sure it is level, and that the top
of the mounting plate is butted up against the bottom edge of
the upper cabinet.
NOTE: If the front edge of the upper cabinet is lower than the
back edge, lower the mounting plate so that its top is level with
the front edge of the cabinet.
the upper cabinet.
7. Using measuring tape, measure out 6" (15.2 cm) on both sides
of the centerline, and mark.
8. Measure down 4" (10.2 cm) from the mark made in Step 6,
and mark.
9. Using a straightedge, draw the 2 horizontal, level lines through
the marks made in steps 6 and 8.
10. Draw the 2 vertical, plumb lines down from the marks made in
Step 7 to complete the 12" x 4" (30.5 x 10.2 cm) rectangle.
This is the venting cutout area.
11. Cut a 3/4" (19 mm) hole in one corner of the cutout area.
12. Using a keyhole saw, cut out the venting cutout area.
D
A
C
Drill Holes in Rear Wall
B
In addition to being installed on at least 1 wall stud, the mounting
plate must attach to the wall at both bottom corner holes. If the
holes are not over wall studs, use two 1/4-20 x 3" round-head
bolts with toggle nuts; if 1 hole is over a wall stud, use 1 lag screw
and one 1/4-20 x 3" round-head bolt with toggle nut; or if both
holes are over wall studs, use 2 lag screws. Following are
3 installation configurations.
A. Rear wall
B. Mounting plate
C. Top of mounting plate must align
with front edge of cabinet.
D. Front edge of upper cabinet
Installation for No Wall Studs at Corner Holes
(Figures 1 & 2)
3. Holding the mounting plate in place, mark both bottom corner
holes.
1. Drill 3/4" (19 mm) holes through the wall at both bottom corner
4. Find the wall stud centerline(s) marked in Step 2 of “Locate
Wall Stud(s),” and mark at least 1, preferably 2, hole(s) through
the mounting plate, closest to the centerline(s). See figures 1,
2 and/or 3 in “Possible Wall Stud Configurations” in “Locate
Wall Stud(s)” section. The blackened holes in the shaded
areas are ideal hole locations.
holes marked in Step 3 of “Mark Rear Wall.”
2. Drill 3/16" (5 mm) hole(s) into the wall stud(s) at the hole(s)
marked in Step 4 of “Mark Rear Wall.” Refer to figures 1 and 2
in “Possible Wall Stud Configurations” in “Locate Wall Stud(s)”
section.
5. Set mounting plate aside.
Installation for Wall Stud at One Corner Hole (Figure 3)
1. Drill a 3/16" (5 mm) hole into the wall stud at the corner hole
marked in Step 3 of “Mark Rear Wall.”
2. If installing on a second wall stud, drill a 3/16" (5 mm) hole into
the wall stud at the other hole marked in Step 4 of “Mark Rear
Wall.” Refer to Figure 3 in “Possible Wall Stud Configurations”
in “Locate Wall Stud(s)” section.
3. Drill a 3/4" (19 mm) hole through the wall at the other corner
hole.
Installation for Wall Studs at Both Corner Holes (Figure 4)
1. Drill 3/16" (5 mm) holes into the studs at the corner holes
marked in Step 3 of “Mark Rear Wall.”
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall Stud at One Corner Hole (Figure 3)
Attach Mounting Plate to Wall
NOTE: Secure the mounting plate to the wall at both bottom
corner holes drilled into the wall studs and/or drywall using either
1/4-20 x 3" round-head bolts and toggle nuts or 1/4 x 2" lag
screws.
1. With the support tabs of the mounting plate facing forward,
insert a 1/4-20 x 3" round-head bolt through the corner hole
that fits over the 3/4" (19 mm) hole drilled in Step 3 of
“Installation for Wall Stud at One Corner Hole” in the “Drill
Holes in Rear Wall” section.
2. Start a toggle nut on the bolt from the back of the mounting
plate. Leave enough space for the toggle nut to go through
the wall and to open.
Refer to illustrations in “Possible Wall Stud Configurations” in
“Locate Wall Stud(s)” section.
No Wall Studs at Corner Holes (Figures 1 & 2)
3. Position mounting plate on the wall, making sure that the top
of the mounting plate is aligned with the front edge of the
upper cabinet.
NOTE: The mounting plate must be secured to the wall on at least
1 wall stud as well as at both bottom corners.
1. With the support tabs of the mounting plate facing forward,
insert 1/4-20 x 3" round-head bolts through both bottom
corner holes of mounting plate.
4. Push the bolt with toggle nut through the drywall, and finger
tighten the bolt to make sure toggle nut has opened against
drywall.
2. Start toggle nuts on bolts from the back of the mounting plate.
Leave enough space for the toggle nuts to go through the wall
and to open.
5. Insert a lag screw into the remaining bottom corner hole.
6. If installing on a second wall stud, insert a lag screw into the
other hole drilled in Step 2 of “Installation for Wall Stud at One
Corner Hole” in the “Drill Holes in Rear Wall” section.
7. Check alignment of mounting plate, making sure it is level.
8. Securely tighten the lag screw(s) and bolt.
B
A
Wall Studs at Both Corner Holes (Figure 4)
C
1. Position mounting plate on the wall, making sure that the top
of the mounting plate is aligned with the front edge of the
upper cabinet.
2. Insert lag screws into both bottom corner holes.
3. Check alignment of mounting plate, making sure it is level.
4. Securely tighten the lag screws.
A. 1/4-20 x 3" round-head bolt
B. Mounting plate
C. Spring toggle nut
3. Position mounting plate on the wall, making sure that the top
of the mounting plate is aligned with the front edge of the
upper cabinet.
4. Push the 2 bolts with toggle nuts through the drywall, and
finger tighten the bolts to make sure toggle nuts have opened
against drywall.
Prepare Upper Cabinet
1. Disconnect power to outlet.
2. Remove all contents from upper cabinet.
3. Place Upper Cabinet Template against the bottom of the
upper cabinet, and tape or tack it in place. Make sure the
template centerline aligns with the vertical centerline on the
rear wall.
C
The “rear wall” arrows must be against the rear wall so that the
holes cut into the upper cabinet align with the holes in the top
of the microwave oven.
D
A
NOTE: If the upper cabinet has a frame around it, trim the
template edges so that it fits inside the frame, against the upper
cabinet bottom. The template has trim lines to use as guides.
B
4. Make sure the 10¹⁄₂" (26.7 cm) dimension from the rear wall to
points “D” and “E” on the template is maintained.
A. 1/4-20 x 3" round-head bolt
B. Mounting plate
C. Drywall
D. Spring toggle nut
5. Insert lag screw(s) into the holes drilled into wall stud(s) in
Step 2 of “Installation for No Wall Studs at Corner Holes” in
the “Drill Holes in Rear Wall” section.
U
p
p
er
-
c
a
bine
t
tem la e
p t
D
E
10¹⁄₂
(26.7 cm)
"
6. Check alignment of mounting plate, making sure it is level.
7. Securely tighten all lag screws and bolts.
10¹⁄₂
(26.7 cm)
"
F
G
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Cut the 1¹⁄₂" (3.8 cm) diameter hole at the circular shaded area
“G” on the template. This hole is for the power supply cord.
NOTE: If upper cabinet is metal, the supply cord bushing needs to
be installed around the supply cord hole, as shown.
A
B
B
A
A. Mounting plate
B. Support tabs
A. Metal cabinet
B. Power supply cord bushing
4. With front of microwave oven still tilted, thread power supply
cord through the power supply cord hole in the bottom of the
upper cabinet.
6. Drill 3/8" (10 mm) holes at points “D” and “E” on the template.
These are for two 1/4-20 x 3" bolts and washers used to
secure the microwave oven to the upper cabinet.
For Roof Venting Installation Only
7. Cut 3/4" (19 mm) hole at one corner of the shaded rectangular
area “F” on Upper Cabinet Template.
8. Using a keyhole saw, cut out the rectangular area.
Install the Microwave Oven
WARNING
5. Rotate microwave oven up toward upper cabinet.
NOTE: If venting through the wall, make sure the damper
assembly fits easily into the vent in the wall cutout.
Excessive Weight Hazard
Use two or more people to move and install
microwave oven.
6. Push microwave oven against mounting plate and hold in
place.
Failure to do so can result in back or other injury.
NOTE: If microwave oven does not need to be adjusted, skip
steps 7-9.
IMPORTANT: The right side of the microwave oven is the heavy
7. If adjustment is required, rotate microwave oven downward.
Using 2 or more people, lift microwave oven off of mounting
plate, and set aside on a protected surface.
side. Handle the microwave oven gently.
1. Place a washer on each 1/4-20 x 3" bolt and place inside
upper cabinet near the 3/8" (10 mm) holes.
8. Loosen mounting plate screws. Adjust mounting plate and
retighten screws.
2. Make sure the microwave oven door is closed and taped shut.
9. Repeat steps 3-6.
10. With the microwave oven centered, and with at least one
person holding it in place, insert bolts through upper cabinet
into microwave oven. Tighten bolts until there is no gap
between upper cabinet and microwave oven.
NOTES:
■
Some upper cabinets may require bolts longer or shorter than
3" (7.6 cm). Longer or shorter bolts are available at most
hardware stores.
■
Overtightening bolts may warp the top of the microwave
oven. To avoid warping, wood filler blocks may be added.
The blocks must be the same thickness as the space
between the upper cabinet bottom and the microwave oven.
3. Using 2 or more people, lift microwave oven and hang it on
support tabs at the bottom of mounting plate.
A
NOTE: To avoid damage to the microwave oven, do not grip or
use the door or door handle while the microwave oven is being
handled.
A. 1/4-20 x 3" bolts
9
Download from Www.Somanuals.com. All Manuals Search And Download.
For Roof Venting Installation Only
Complete Installation
1. Refer to the Use and Care Guide for instructions on how to
1. Insert damper assembly through the cabinet cutout so that the
long tab of the damper assembly slides into the slot on the left
side of the damper vent opening, as shown. Then secure with
mounting screw.
NOTE: The screw cannot be installed if the damper assembly is
not positioned as shown.
install filters into your model.
WARNING
A
B
C
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
D
Do not use an extension cord.
A. Long tab (inside slot)
B. Damper assembly
C. Mounting screw
Failure to follow these instructions can result in death,
fire, or electrical shock.
D. Upper cabinet cutout
2. Plug microwave oven into grounded 3 prong outlet.
3. Reconnect power.
2. Connect vent to damper assembly.
4. Check the operation of microwave oven by placing 1 cup
(250 mL) of water on the turntable, and programming a cook
time of 1 minute at 100% power. Test vent fan and exhaust by
operating the vent fan.
A
B
5. If the microwave oven does not operate:
■
Check that a household fuse has not blown, or that a
circuit breaker has not tripped. Replace the fuse or reset
the circuit breaker. If the problem continues, call an
electrician.
■
■
Check that the power supply cord is plugged into a
grounded 3 prong outlet.
See the Use and Care Guide for troubleshooting
information.
Installation is now complete.
A. Vent
Save Installation Instructions for future use.
B. Damper assembly (under vent)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING DESIGN SPECIFICATIONS
This section is intended for architectural designer and
Rectangular to Round Transition
NOTE: The minimum 3" (7.6 cm) clearance must exist between
the top of the microwave oven and the rectangular to round
transition piece so that the damper can open freely and fully.
builder/contractor reference only.
NOTES:
■
Vent materials needed for installation are not provided with
microwave hood.
■
■
We do not recommend using a flexible metal vent.
A
To avoid possible product damage, be sure to vent air outside,
unless using recirculation installation. Do not vent exhaust air
into concealed spaces, such as spaces within walls or
ceilings, attics, crawl spaces or garages.
B
D
C
For optimal venting installation, we recommend:
■
■
■
using roof or wall caps that have back draft dampers
E
using a rigid metal vent
F
3" (7.6 cm)
using the most direct route by minimizing the length of the
vent and number of elbows to provide efficient performance
■
■
■
using uniformly sized vents
using duct tape to seal all joints in the vent system
A. Roof cap
B. 6" (15.2 cm) min. diameter round vent
C. Elbow (for wall venting only)
D. Wall cap
E. 3¹⁄₄" x 10" to 6" (8.3 x 25.4 cm to 15.2 cm)
rectangular to round transition piece
using caulking compound to seal exterior wall or roof opening
around cap
■
not installing 2 elbows together, for optimal hood performance
If venting through the wall, be sure that there is proper clearance
within the wall for the damper to open fully.
F. Vent extension piece, at least 3" (7.6 cm) high
If venting through the roof, and rectangular to round transition is
used, be sure there is at least 3" (7.6 cm) of clearance between
the top of the microwave oven and the transition piece. See
“Rectangular to Round Transition” illustration.
Recommended Standard Fittings
The following length equivalents are for use when figuring vent
length. See the examples in “Recommended Vent Length.”
A
B
C
Roof venting
Roof cap
D
E
F
G
A. Rectangular to round transition piece: 3¹⁄₄" x 10" to 6" = 5 ft
(8.3 x 25.4 cm to 15.2 cm = 1.5 m)
B. Roof cap: 3¹⁄₄" x 10" = 24 ft (8.3 x 25.4 cm = 7.3 m)
C. 90° elbow: 3¹ꢀ₄" x 10" = 25 ft (8.3 x 25.4 cm = 7.6 m)
D. 90° elbow: 6" = 10 ft (15.2 cm = 3 m)
E. Wall cap: 3¹⁄₄" x 10" = 40 ft (8.3 x 25.4 cm = 12.2 m)
F. 45° elbow: 6" = 5 ft (15.2 cm = 1.5 m)
Wall venting
Wall cap
G. 90° flat elbow: 3¹⁄₄" x 10" = 10 ft (8.3 x 25.4 cm = 3 m)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended Vent Length
A 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent
should be used.
6" (15.2 cm) vent system = 73 ft (22.2 m) total
The total length of the vent system including straight vent,
elbow(s), transitions and wall or roof caps must not exceed the
equivalent of 140 ft (42.7 m) for either type of vent. See
“Recommended Standard Fittings” section for equivalent lengths.
A
B
6 ft (1.8 m)
For best performance, use no more than three 90° elbows.
To calculate the length of the system you need, add the equivalent
lengths of each vent piece used in the system. See the following
examples:
2 ft
(0.6 m)
3¹⁄₄" x 10" (8.3 x 25.4 cm) vent system = 73 ft (22.2 m) total
A
B
6 ft (1.8 m)
C
D
A. Two 90° elbows = 20 ft (6.1 m)
B. 1 wall cap = 40 ft (12.2 m)
2 ft
C. 1 rectangular to round transition piece = 5 ft (1.5 m)
D. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m)
(0.6 m)
C
If the existing vent is round, a rectangular to round transition piece
must be used. In addition, a rectangular 3" (7.6 cm) extension vent
between the damper assembly and rectangular to round transition
piece must be installed to keep the damper from sticking.
A. One 3¹⁄₄" x 10" (8.3 x 25.4 cm) 90° elbow = 25 ft (7.6 m)
B. 1 wall cap = 40 ft (12.2 m)
C. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m)
ASSISTANCE
Call your authorized dealer or service center. When you call, you
will need the microwave oven model number and serial number.
Both numbers can be found on the model and serial number
plate, which is located behind the microwave oven door on the
front frame of the microwave oven.
If you need additional assistance, call us at our toll free number or
visit our website listed in the Use and Care Guide.
Replacement Parts
If any of the installation hardware needs to be replaced, call us at
our toll free number listed in the Use and Care Guide, and
reference the appropriate part number listed here.
Damper Assembly
Mounting Screw Kit (includes
parts A-G in “Parts Supplied” in
the “Tools and Parts” section)
Part Number W10128803
Part Number 8206442
Mounting Plate
Part Number 8206319
Vent Deflector
Upper Cabinet Template
Part Number 8205274
Part Number 8205980
W10189719A
461965621022
3/08
Printed in China
SP PN W10190015A
© 2008. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|