Congratulations
Kirby Sentria in Moscow - $2000 - Tel: (495) 506-9032
Dear Kirby Customer,
Congratulations on your purchase. You now own a superior,
complete home care system designed to help make your home
and furnishings look better and last longer. Most importantly,
repeated use of your Kirby Sentria™ system will give you the
type of clean in-home environment you want and deserve.
This use and care manual is designed to help you get the most out
of your new Sentria home care system and enjoy its numerous ben•
efits and features. The Owner's DVD (where available) will give you
step-by-step instructions on your machine's operation. Your local
distributor is available should you have any further questions.
The Kirby Company, the hallmark of innovation and quality for
over 90 years, sells through the in-home sales method in over 70
countries. We want you to know that every customer is important
to us and that we sincerely appreciate your business.
Please enjoy your Sentria home care system to its fullest!
This manual is written for use with the Kirby® Sentria™ home care system.
For assistance, contact your local authorized distributor.
The Kirby Company, 1920 West 114th Street, Cleveland, Ohio 44102, U.S.A.
Kirby, Micron Magic, Splitsecond, Splitsecond 2, Scuttle, Odorific, Tech Drive, Miracle Waxer, Handi-Bulter and Mini Em-Tor are
registered trademarks of The Scott Fetzer Company.
Sentria is a trademark of The Scott Fetzer Company.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Important Safety Instructions
About this Manual
2
4
5
6
Kirby® Micron Magic® HEPA Filtration
Part 1 - Getting Started
Moving Your System/Handle Tilt Latch Lock/Toe-Touch Control
Power Nozzle Height Adjustment/Tech Drive® Power Assist
Installing/Changing Disposable Filter Bags
Bag Support Strap/Mini Em-Tor® Collector/The Belt Lifter
Part 2 — Upright & Portable Cleaner
Upright Cord Management
7
8
9
10
12
18
13
14
15
16
The Upright Cleaner
Straight Suction Cleaner
The Portable Cleaner
Part 3 — Canister Cleaner & Attachments
Converting to a Canister Cleaner/Installing the Attachment Hose
Extension Tubes/Surface Nozzle/Duster Brush
Upholstery Nozzle/Crevice Tool/Wall & Ceiling Brash
Massage Cup/Suction Control Grip
Using Your Sentria System as a Blower
The Portable Sprayer
19
20
21
22
23
25
27
The Portable Shampooer
Part 4 — Optional Accessories
29
The Carpet Shampoo System
30
36
37
39
41
42
45
46
Kirby Guard Carpet & Upholstery Protector
The Miracle Waxer® - Floor Polisher
The Floor Care System - Floor Buffer
The Floor Care System - Carpet Fluffer
The Turbo Accessory System
The Zippbrush
The Handi-Butler® Tool
54
Part 5 — Operating/Maintenance Tips
Changing the Power Nozzle Belt
55
56
58
59
64
Adjusting the Brush Roll Height
Miscellaneous Parts Replacement
Questions and Answers/Troubleshooting
Other Fine Kirby® Cleaning Products
Index
66
68
Expanded Illustration of the Sentria model & Accessories
If you have any questions regarding your purchase or the operation of your Kirby Home Care
System, please contact your local authorized distributorship:
OR
You may contact The Kirby Company's Consumer Relations Department by:
e-mail
telephone 1-800-494-8586
fax 216-529-6146
mail
Consumer Relations
1920 West 114th Street
Cleveland, Ohio 44102
Our business hours are 8:00 a.m. to 5:00 p.m. Eastern Time, U.S.A. Monday through Friday.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
This Owner's Manual was designed to be easy to read and follow. It has been organized in
sections based on the various ways you may use your new Kirby® Sentria™ system. Within
each section, simple step-by-step illustrations will help you easily visualize the steps required to
properly operate your new Sentria system and its many attachments and optional accessories.
Please note: Illustrations and descriptions of each part of your new Sentria home care system
can be found in the rear of the manual. Please refer to these illustrations and corresponding (#'s)
as you read the manual.
In addition to the Table of Contents on page 3, you will also find an Index on page 66 that
will refer you to the information you require.
We sincerely hope this Owner's Manual will help you obtain years of satisfactory world-class
performance from the Sentria home care system by Kirby.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MICRON MAGIC®
• • • • H E P A F I L T R A T I O N
With MicroAllergen Technology
You bought the best; you expect the best. That's why the Kirby Company developed the
Micron Magic HEPA (High Efficiency Particle Arrest) Filtration System featuring the latest
in clean air technology without sacrificing tremendous airflow.
Your new Sentria™ system includes our BEST filters:
•
•
•
Traps over 99% of particles as small as 0.3 microns
Rated HEPA 11
Minimizes bag odor
So, what does this mean?
Improved Indoor Air Quality!
These improvements are a part of the Kirby Company's pursuit to respond to our customers'
needs. The Kirby Micron Magic HEPA Filtration System demonstrates the quality you expect
and the performance you deserve.
Reorder genuine Kirby Micron Magic HEPA filter bags with MicroAllergen Technology from
your local authorized Kirby Distributor.
The Carpet and Rug Institute (CRI) has
awarded the Kirby home care system
its "Green Label" seal of approval for
meeting the organization's requirements
for soil removal, dust containment and
appearance retention.
For those who appreciate Quality, Reliability and Performance
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
PART ONE
This section outlines general information you will need as
you begin using your new Sentria™ system. It includes infor•
mation on:
Moving and Carrying Your System
Using the Handle Tilt Latch Lock
The Toe-Touch Control
Proper Power Nozzle Height
Using Tech Drive® Power Assist
Installing/Changing Disposable Filter Bags
Emptying the Mini Em-Tor® Collector
Understanding the Belt Lifter
Please read this section (as well as all other sections) carefully
before using your new Sentria home care system.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
MOVING YOUR SYSTEM
Your Sentria system is equipped with Tech Drive® power
assist. In order to push your unit with the motor OFF, the
Tech Drive Pedal (11) must be turned OFF (disengaged).
Turn Tech Drive power assist OFF by pushing down on the
gray "N" side (marked "N" for Neutral) of the Tech Drive N/
D Pedal. (See page 8 for additional information.)
CARRYING YOUR SYSTEM
NOTE: The Carrying Grip (18) is designed for convenience in
carrying your Sentria system. •
HANDLE TILT LATCH LOCK
The Handle Tilt Latch Lock (10) serves two purposes:
To allow you to lift the front of the Sentria system over
door thresholds or throw rugs. To do so, move the Tilt
Latch Lock towards the bag. By doing this, the handle
will only lower part way. This allows you to push down on the
locked handle and lift the front of the unit. >
1
To allow you to store your Sentria system in a
vertical position or carry it.
2
To do this, lower the handle to a horizontal position near the
floor. While pushing the handle down, move the Tilt Latch
Lock away from the bag to lock the handle down. You can
now stand the unit up onto its bumper and lean it against a
wall for storage.
This vertical position may also be useful in carrying the unit.
To lift the unit, use the Carrying Grip (18). •
TOE-TOUCH CONTROL
The Toe-Touch Control (8), (9), located over the front
wheel, raises and lowers the front of your Sentria system.
Step down on the Toe-Touch Control Bottom Pedal (9) to raise
the front. •
Never unlock the Handle Tilt Latch without holding on to the handle. The
handle is spring-loaded and could quickly pivot upward when unlatched.
/!\ CAUTION:
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
POWER NOZZLE HEIGHT ADJUSTMENT
When using the Power Nozzle (25), it is important to adjust
the height properly. Start by pressing the Toe-Touch Control
Bottom Pedal (9) all the way down, raising the front of your
system all the way up.
The Toe-Touch Control adjusts the Power Nozzle to seven
different heights. The highest four positions are used for attach•
ing accessories. Positions #1-3 are used for carpet and floor
cleaning. Positions #1-3 are indicated when the number shows
directly in front of the Toe-Touch Control Upper Pedal (8).
Turn the unit on and press the Toe-Touch Control upper
pedal 4 times (one notch at a time) until you see the #3 in
front of the Toe-Touch Control Upper Pedal. You are now at
the HIGHEST floor cleaning position used for high-pile and
plush carpets.
Press one more notch down for the MEDIUM position
(until you see the #2 in front of the Toe-Touch Control Upper
Pedal.) This is the most widely used position for all-type
carpets. Push one more notch down for LOW (until you see
the #1 in front of the Toe-Touch Control upper pedal). This is
the lowest position for low pile carpet and hard floor cleaning.
NOTE: When finished vacuuming, press the Toe-Touch
Control Bottom Pedal all the way down to move your
Sentria system. •
TECH DRIVE® POWER ASSIST
Your new Sentria system is equipped with Tech Drive power
assist. This innovative feature eliminates most of the effort
required to move your Sentria system back and forth. •
TURNING TECH DRIVE POWER ASSIST
ON (DRIVE)
To engage Tech Drive power assist push down the red "D"
side (marked "D" for Drive) of the Tech Drive N/D Pedal (12)
located just below the Power Switch. (13)
You may use your Sentria system without Tech Drive power
assist if desired. Simply put the Tech Drive pedal in Neutral. •
To avoid possible damage to soft tiles or marking of waxed and
finished non-carpeted floors, disengage the Tech Drive pedal.
/!\ IMPORTANT:
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
TURNING TECH DRIVE POWER ASSIST
OFF (NEUTRAL)
To move your Sentria™ system with the motor OFF or to
vacuum without power assist, Tech Drive power assist must
be put in Neutral.
To place Tech Drive power assist in Neutral, push down the
gray "N" side (marked "N" for Neutral) of the Tech Drive
N/D Pedal (11). •
INSTALLING/CHANGING DISPOSABLE
FILTER BAGS
A Disposable Filter Bag must be installed before you begin
vacuuming.
To install a new Disposable Filter Bag, unzip the Outer
Permanent Bag (1) and pull out the Disposable Filter
Bag along with the Top Adaptor (5). >
1
2
When necessary, remove the used Disposable Filter Bag.
NOTE: Always replace the Disposable Filter Bag
when dirt reaches the "FULL" line on the bag. Failure
to do so will affect performance.
From the rear of the Disposable Bag, grasp the cardboard
faceplate. Holding the Top Adaptor steady, rotate the cardboard
faceplate to the left (counter-clockwise). When the lock tabs on
the Top Adaptor align with the slots in the cardboard faceplate,
gently pull the bag off. >
To install a new Disposable Filter Bag, grasp the card-
board faceplate from the rear of the Disposable Filter
bag. Align the slots in the cardboard faceplate on the
Disposable Filter Bag with the lock tabs on the Top Adaptor.
Then push the Top Adaptor into the bag opening.
3
Holding the Top Adaptor steady, rotate the cardboard faceplate
to the right (clockwise) to secure the Disposable Filter Bag.
NOTE: To avoid air leaks, make sure the cardboard faceplate
is securely positioned up against the flat portion of the Top
Adaptor. >
Before changing the Disposable Filter Bag, unplug the power cord
from the wall outlet and be sure that the motor and fan have stopped.
/!\ CAUTION:
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
BAG SUPPORT STRAP
Check to make sure the Bag Support Strap (4)is con-
nected to the Top Adaptor (5). The Bag Support Strap
4provides the support required for proper operation of
the Disposable Filter Bag.
If it is not connected, thread the strap through the small hole
of the Top Adaptor. Then place the hole in the strap over the
stud on the Top Adaptor.
Finally, insert the adaptor and new filter bag into the Outer
Permanent Bag (1)and close the zipper completely for
maximum performance.
NOTE: In order for the Filtration System to perform effectively,
use only Kirby® Micron Magic® HEPA Filtration Bags. If the
outside bag is torn or damaged, please replace immediately. •
EMPTYING THE MINI EM-TOR® COLLECTOR
The Mini Em-Tor (6) collector is designed to collect large,
heavy particles which can be emptied by removing the Mini
Em-Tor collector.
To remove, grasp the Mini Em-Tor collector in the
handhold provided and rotate it away from the body of
the system as far as it will go, then lift it off.
1
The top of the bag is released from the handle by pressing the
Bag Release Button (16). After removing the Mini Em-Tor col•
lector and the entire Bag Assembly, position the front opening
of the Mini Em-Tor collector over a newspaper and shake it to
remove the particles. >
To replace the Mini Em-Tor collector, re-attach the entire
Bag Assembly by inserting the Bag Latch Tab (2)at the top
of the bag into the slot under the Bag Release Button (16).
2
Finally, line up the raised indicator arrow of the Mini Em-Tor
collector with the indicator arrow on the Air Exhaust Port (19).
Rotate the Mini Em-Tor collector towards the Sentria system
and lock it in place.
NOTE: The Mini Em-Tor collector must be securely locked
in place or the unit will not operate. •
USING THE BELT LIFTER
The Belt Lifter (20) on your Sentria system is used for two
purposes:
1) To engage or disengage the Brush Roll. When the Brush Roll
is disengaged, the Sentria system can be used as a straight suc•
tion cleaner (page 15), and;
2) To allow removal of the Power Nozzle when converting
your Sentria system for use with various attachments and
optional accessories.
To avoid damaging the belt, turn the Sentria system OFF
before using the Belt Lifter. >
Do not pick up heavy objects, such as coins, screws, rocks or similar
objects. This may damage the fan.
/!\ CAUTION:
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
USING THE BELT LIFTER (cont)
To use the Belt Lifter, you must first raise the Headlight
Hood (21). >
1
Flip out the handle on the Belt Lifter (20). Use it to turn
the Belt Lifter fully to the left (counter-clockwise) until
it stops and the red arrows line up. This stretches the
2
belt and lifts it off the motor shaft. Return the handle on the
Belt Lifter to its closed position.
If you are using your Sentria™ system as a straight suction
cleaner, simply lower the Headlight Hood. The Brush Roll is
now disengaged and will not rotate when the power switch is
turned ON. >
The belt will be stretched to the top of the nozzle as
shown. >
3
To re-engage the belt so the Brush Roll rotates, simply
raise the Headlight Hood and use the handle to turn the
4Belt Lifter fully to the right (clockwise) until the green
arrows line up. Then lower the Headlight Hood.
The Brash Roll will now rotate when the Power Switch is
turned ON.
NOTE: The belt should not be stretched when stored for
an extended period. Make sure the green arrows line up
for storage. >
Your Sentria system is equipped with a Brush Roll
Performance Indicator Light (7), located on the top
right side of the Power Nozzle. The purpose of this
light is to show if the Brush Roll is rotating properly.
5
If the Brush Roll Indicator Light flashes intermittently or
does not come on when using the Power Nozzle, the Brush
Roll Belt may not be working properly. Either the Belt is not
engaged or may need to be replaced.
To replace the Brush Roll Belt, also called the Power Nozzle
Belt, see Page 55. •
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Upright & Portable Cleaner
PART TWO
Your Sentria™ home care system is extremely versatile.
In this section, we will discuss the following:
Upright Cord Management
Using your Sentria System as an
Upright Cleaner
Using your Upright as a Straight
Suction Cleaner
Cleaning Hard-Surface Floors
Using your Sentria System as a
Portable Cleaner
Cleaning Mattresses and Carpeted Stairs
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Upright & Portable Cleaner
UPRIGHT CORD MANAGEMENT
The Sentria system Upright handle incorporates a series of
hooks and fasteners to keep the cord off the floor and attached
to the upright handle for your convenience.
When using your Sentria system as an upright, snap
the power cord into the two cord holders located on the
back of the handle. >
1
With the Upper Cord Hook in the up or 12 o'clock
position, route the cord toward the rear of the unit and
slide the cord in to the c-shaped holder on the Upper
2
Cord Hook. The cord can now be wrapped around the Upper
and Lower Cord Hooks for storage. To quick-release the
cord for use, rotate the Upper Cord Hook down to the 6
o'clock position. The c-shaped holder is designed to hold the
cord securely in place and prevent the first loop from drop•
ping to the floor.
NOTE: The cord can only be inserted or removed from the
c-shaped holder when the Upper Cord Hook is in the 12
o'clock position. •
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Upright & Portable Cleaner
THE UPRIGHT CLEANER
Before you begin vacuuming, it's important to have the Power
Nozzle (25) adjusted to the proper height setting. This gives you
the most efficient cleaning action. Lowering the Power Nozzle
too far prevents proper cleaning and shortens belt life.
The proper height setting can be achieved by doing
the following: >
Before you turn the Sentria™ system ON, raise the
Power Nozzle by stepping on the Toe Touch Control
1Bottom Pedal (9) all the way down. >
Turn the Sentria system ON by pressing the Power
Switch (13). >
2
Press the Toe-Touch Control Upper Pedal 4 times.
You are now at the HIGHEST floor cleaning position
(indicated by the #3 showing in front of the Toe-Touch
Control Upper Pedal). Press the pedal again for medium
carpets (indicated by the #2) and again for low pile carpets
(indicated by the #1.) >
3
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Upright & Portable Cleaner
If desired, engage Tech Drive® power assist by
pushing down the red "D" side (marked "D" for Drive)
of the Tech Drive N/D Pedal (12) located just below the
Power Switch (13). >
4
To turn your Sentria™ system OFF, press the Toe-
Touch Control Bottom Pedal (9) all the way down until
nozzle is fully raised.
5
Disengage Tech Drive power assist by stepping on the gray
"N" side (marked "N" for Neutral) of the Tech Drive N/D
Pedal (11).
Turn the Sentria system OFF by pressing the Power Switch
(13) and then unplugging. •
STRAIGHT SUCTION CLEANER
Straight Suction Cleaning allows you to vacuum hard floors,
throw rugs and delicate carpets without use of the Brush Roll.
NOTE: When using Straight Suction Cleaning without the Hard
Floor Pad, either on carpets or bare floors, lower the nozzle as
close as possible to the floor without touching the floor.
With the Sentria system turned OFF, raise the
Headlight Hood (21). >
1
Flip out the handle on the Belt Lifter (20). Use it to turn
the Belt Lifter all the way to the left (counter-clock-
2wise) until the red arrows line up (see page 10). Return
the handle on the Belt Lifter to its closed position.
Then lower the Headlight Hood.
The Brush Roll is now disengaged and your Sentria system
will operate as a Straight Suction Cleaner. •
Tech Drive pedal must be in neutral when using the cleaner on hard
surface floors.
/!\ NOTICE:
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Upright & Portable Cleaner
THE HARD FLOOR PAD (optional)
By attaching the optional Hard Floor Pad to your Sentria™,
system you may dust bare floors. While the unit is turned
OFF, raise the Power Nozzle (25) as far as it will go by press•
ing the Toe-Touch Control Bottom Pedal (9). Attach the
Hard Floor Pad onto the nozzle opening using the spring
clips on the plate. Then lower the Power Nozzle by pressing
the Toe-Touch Control Upper Pedal (8) one notch at a time
until the bristles touch the floor.
NOTE: The Hard Floor Pad should only be used when the
unit is in the Straight Suction Cleaner mode. •
PORTABLE CLEANER SET-UP
Besides being a remarkable Upright Cleaner, the Sentria sys•
tem can easily be converted into a portable cleaner for mat•
tresses and carpeted stairs.
To convert your Sentria system to a Portable Cleaner,
make sure the unit is turned OFF, unplugged, and the
Tech Drive® pedal is in neutral.
1
Then release the Outer Permanent Bag Top from the Bag
Support by pressing the Bag Release Button (16) and sliding
the bag top off. >
Remove the cord from the handle. With the Upright
Handle (17) in the vertical position, push the Handle
2Release Button (14), located at the base of the handle,
and pull the handle straight up and out of the slot.
(Bag not shown for clarity.) >
Insert the Portable Handle (15) into the slot where the
Upright Handle was connected. Push the Portable
3Handle into the slot until it snaps into place. >
Before installing the Hard Floor Pad, turn unit OFF, unplug the power cord
from the wall outlet and be sure the motor and nozzle brush have stopped.
/!\ CAUTION:
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Upright & Portable Cleaner
PORTABLE CLEANER SET-UP (cont)
Bend the Filtration Bag Assembly (1) in half and insert
the Bag Latch Tab (2) into the slot on the Portable
4Handle until it snaps into place.
You are now ready for portable power cleaning. •
NOTE: Do not use portable mode on upholstered furniture.
CARPETED STAIRS
Place your Sentria™ system on one of the carpeted steps, while
supporting the rear. Turn the unit on after it is in place and make
sure the Tech Drive® pedal is in the Neutral position.
Roll the cleaner back and forth so that the Brush Roll
agitates the carpeting and loosens the dirt. •
MATTRESS CLEANING
Cleaning mattress surfaces is done the same as carpeted
stairs, except that you need to disengage the Brush Roll. (If
your mattress has tufted buttons on the surface, the Brush
Roll could pull them loose.)
NOTE: Do not carry the portable unit with the motor on. Place
the unit on the surface you wish to clean and then turn the unit
on. Turn the unit off to move it to a new location.
For straight suction cleaning, raise the Headlight Hood (21)
and flip out the handle on the Belt Lifter (20). Use it to turn
the Belt Lifter all the way to the left (counter-clockwise)
until the red arrows line up. This will stop the Brush Roll
from turning.
Return the handle on the Belt Lifter to its closed position
and lower the Headlight Hood. Use the Toe-Touch Control
to adjust the Power Nozzle to its lowest setting. •
To reduce risk of injury in the portable mode, keep hair and loose clothing
away from the Sentria system while in operation.
/!\ CAUTION:
Also make sure Tech Drive® pedal is in the neutral position when
vacuuming stairs and mattresses. In addition, the Brush Roll should
be disengaged when vacuuming mattresses.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Cleaner & Attachments
PART THREE
Your Kirby® Sentria™ system comes with a wide variety
of attachments for added versatility. In this section, we will
discuss the following:
Removing the Power Nozzle to Convert
to a Canister Cleaner
Using the Attachments
Using the Suction Control Grip
Using as a Blower Unit
Using the Portable Sprayer and the
Portable Shampooer
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Cleaner & Attachments
CONVERTING TO A CANISTER CLEANER/
INSTALLING THE ATTACHMENT HOSE
When using different cleaning attachments, the Attachment
Hose is connected to the front of the cleaner in place of the
Power Nozzle (25).
NOTE: When connecting the Attachment Hose, you may
choose between the Upright Handle (17) or the Portable
Handle (15). To install the Portable Handle, see page 16.
To install the Attachment Hose, you must first convert
to a Canister by removing the Power Nozzle. To do so,
1 press the Toe-Touch Control Bottom Pedal (9) all the
way down until nozzle is fully raised. Disengage Tech Drive®
power assist by stepping on the gray "N" side (marked "N" for
Neutral) of the Tech Drive N/D Pedal (11). Turn the Sentria™
system OFF by pressing the Power Switch (13) and then
unplugging. >
Raise the Headlight Hood (21) and flip out the handle
on the Belt Lifter (20). Use it to turn the Belt Lifter all
2the way to the left (counter-clockwise) until the red
-
arrows line up.
Unlock the Power Nozzle by turning the Accessory Lock
(22) all the way to the left (counter-clockwise). The Power
3Nozzle should tip forward when it is released. Lift the
nozzle away from the Sentria system. >
At the connector end of the Attachment Hose, you will
notice two hooks. Place the hooks over the ends of the
4 Attaching Bar (24), then push the opening of the hose
up against the Sentria system. >
Lock the Attachment Hose Connector in place by
turning the Accessory Lock (22) all the way to the
right (clockwise). (Accessory Lock will clamp the
5
Attachment Hose to the unit.)
With the Attachment Hose in place, the unit will
automatically adjust to high speed for hose operation.
NOTE: If the Sentria system will not run when the Power
Switch is ON, see page 59. •
In normal operation, friction between the belt and the metal motor
shaft may cause the metal motor shaft to become hot to the touch.
/!\ CAUTION:
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Cleaner & Attachments
INSTALLING ATTACHMENTS ON THE
ATTACHMENT HOSE
To attach tools to the hose, push lightly while twisting the
smaller end of the hose into the tool. •
EXTENSION TUBES
One or two Extension Tubes can be attached to the end of
the hose to extend your reach and efficiently use various
attachments. •
SURFACE NOZZLE
UNDER LOW FURNITURE/BARE FLOORS
The Surface Nozzle should be used on bare floors or for
surface cleaning carpets and under low furniture.
Rubber wheels on the nozzle allow it to glide silently on the
surface of hard floors without scratching and vacuum with
maximum power. •
DUSTER BRUSH
The Duster Brush may be connected to the Attachment
Hose or the Extension Tubes to remove dust from any
surface, including contoured or irregular surfaces. •
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Cleaner & Attachments
UPHOLSTERY NOZZLE
The Upholstery Nozzle is used for cleaning upholstered
furniture, carpeted steps, and clothing. It can also be used
to clean the inside of cars. •
CREVICE TOOL WITH REMOVABLE BRUSH
Without the removable brush, the Crevice Tool can be used
for cleaning cracks, crevices, corners, grooves and narrow
openings.
Install the removable brush in the end of the Crevice Tool to
remove dirt from corners, button tufts, between radiator coils
and sliding window tracks. •
WALL & CEILING BRUSH
To vacuum walls, ceilings, drapes and other surfaces,
attach the Wall & Ceiling Brush to the Suction Control
Grip. Then attach the Suction Control Grip to the Extension
Tube(s) as shown. In addition to providing suction relief, the
Suction Control Grip provides the proper angle to comfort•
ably vacuum walls and ceilings.
Tip: To vacuum the top of door frames or ledges, or books
on a bookshelf, rotate the Wall & Ceiling Brush 180°. •
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Cleaner & Attachments
MASSAGE CUP
Used with the Attachment Hose, the Massage Cup provides
an invigorating skin or scalp massage. It can also be used to
clean the floors of cars. •
CONTROLLING AIRFLOW WITH THE
SUCTION CONTROL GRIP
Sometimes when using the attachments, vacuuming drapes or
delicate lamp shades, for example, you might wish to control
the amount of suction.
The Suction Control Grip features a valve to control the
amount of suction. Slide the control back and forth until the
desired level of suction is reached.
The Suction Control Grip can be used with or without the
Extension Tubes. •
SUCTION CONTROL GRIP PLACEMENT
The Suction Control Grip may be used at the end of the
Extension Tubes for reaching up or at the beginning of the
Extension Tubes for reaching down. •
To avoid irritation or damage to eyes or ears, keep the massage cup
and all other accessories a safe distance away.
/!\ CAUTION:
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Cleaner & Attachments
BLOWER SET-UP
Your Sentria system can also be used as a blower. To do so,
you must first remove the Power Nozzle (25).
NOTE: When using your Sentria system as a blower, you
may choose between the Upright Handle (17) or the Portable
Handle (15).
Turn the power OFF, place the Tech Drive® power
assist in Neutral (see page 8 for details), unplug
1the unit from the wall outlet and press the Toe-Touch
Control Bottom Pedal (9) all the way down until noz•
zle is fully raised. >
Raise the Headlight Hood (21) and flip out the handle
on the Belt Lifter (20). Use it to turn the Belt Lifter all
the way to the left (counter-clockwise) until the red
2
arrows line up. >
Unlock the Power Nozzle (25) by turning the Accessory
Lock (22) all the way to the left (counter-clockwise). The
3Power Nozzle should tip forward when it is released.
Lift nozzle away from the Sentria system. >
When using the blower attachments, the Air Intake
Guard must be attached to the front of the unit.
4
Fasten the Air Intake Guard onto the Attaching Bar (24)
the same way you would the Attachment Hose. Then lock it
on by turning the Accessory Lock (22) all the way to the right
(clockwise). >
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Cleaner & Attachments
BLOWER SET-UP (cont)
To remove the entire Bag Assembly, grasp the Mini
Em-Tor® collector (6) in the hand-hold provided and
5rotate it out and away from the Sentria system as far as
it will go. Then lift it off.
Release the Outer Permanent Bag Top from the Bag Support
by pressing the Bag Release Button (16) and sliding the bag
top down. >
Place the large end of the Attachment Hose over the
Air Exhaust Port (19). Line up the Indicator Arrow
6on the Hose End with the Indicator Arrow on the Air
Exhaust Port and twist the Hose Connector to the right
(clockwise) to lock it in place.
If the Sentria system will not operate, see page 59. •
USING AS A BLOWER
Your Sentria system may now be used as a blower.
By attaching the Inflator/Deflator Tool to the Attachment
Hose, you can inflate toys, air mattresses or any other
low-pressure inflatable item up to 1 p.s.i. (pounds per
square inch of air pressure). >
To deflate items, connect the Attachment Hose to the front
of the unit and connect the Inflator/Deflator Tool to the
Attachment Hose. Then connect the Bag Assembly to the
Air Exhaust Port.
You may now use your Sentria system to deflate items.
NOTE: You can also use this set-up to clean tight areas such
as computer keyboards and audio/video equipment. •
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Cleaner & Attachments
THE PORTABLE SPRAYER
The Portable Sprayer is used only in the Blower Mode.
It is an excellent tool to apply many different types of
water-based liquids to any type of surface. The spray can
be adjusted ranging from very fine to coarse.
PORTABLE SPRAYER SET-UP
Unscrew the jar from the Portable Sprayer and fill 3/4
full with non-flammable liquid. Before reinstalling the
1jar, make sure the portable sprayer dip tube is attached
to the spray gun body. >
Screw the jar tightly on the Portable Sprayer and attach
the Portable Sprayer to the end of the Attachment Hose
2in the Blower Mode.
Make certain your Sentria™ system is set up as a Blower
Unit. The Attachment Hose should be connected to the Air
Exhaust Port (19). •
USING THE PORTABLE SPRAYER
Holding the Portable Sprayer horizontally, aim it
toward a sheet of newspaper. Turn the Sentria system
1ON and squeeze the Portable Sprayer trigger, spraying
your non-flammable solution onto the newspaper to
check spray pattern.
NOTE: If the Portable Sprayer must be tilted during usage,
less solution should be used in the jar. This will help avoid
large droplets in the spray. >
Never use oil or solvent based paint of any kind in the Portable Sprayer. The
motor is open to the spray and could ignite flammable and volatile solvents.
/!\ WARNING:
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Cleaner & Attachments
USING THE PORTABLE SPRAYER (cont)
With the nozzle pointed away from you, adjust the
spray by turning the Spray Adjustment Control on
the trigger of the Portable Sprayer. >
2
Use slow, sweeping motions to spray the desired
area with solution. Always squeeze the trigger fully
to permit maximum flow. This will give you the best
spray control. •
3
CLEANING THE PORTABLE SPRAYER
Immediately after use, empty the Portable Sprayer jar
and wash with warm soapy water. >
1
The Portable Sprayer dip tube should also be removed
and washed. (Make sure to reinstall it after cleaning.) >
2
Never clean the Portable Sprayer with flammable cleaning fluids.
The motor is open to the spray and could ignite the spray.
/!\ WARNING:
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Cleaner & Attachments
CLEANING THE PORTABLE SPRAYER (cont)
The spray opening on the front of the Sprayer also
pulls out so that the inside of the Sprayer and the
nozzle jet can be cleaned.
3
To remove the nozzle jet, press on the two latches on the
front of the nozzle jet and pull it out. (The latches must
be aligned with the holes on the front of the Sprayer when
returning the nozzle jet to the front of the Sprayer.)
Then, fill the jar with water. Spray water until the spray
becomes clear. Reassemble the Sprayer after cleaning so
none of the parts will be lost. •
PORTABLE SHAMPOOER SET-UP
The Portable Shampooer is used in the Blower Mode only.
It is designed for fast and easy cleaning of carpeted stairways
and areas that are difficult to reach with the Carpet Shampoo
System.
To set up the Portable Shampooer, attach the Portable
Shampooer cap to the end of the Portable Sprayer. >
1
Remove the jar from the Portable Sprayer and fill
the jar about 3/4 full with Kirby® Carpet Shampoo
mixture (Mix according to the instructions on the
bottle.) USE ONLY KIRBY CARPET SHAMPOO for
best results. >
Screw the jar tightly on the Portable Sprayer, then
attach the Sprayer to the Attachment Hose.
3
(Make certain your Sentria™ system is set up as a
Blower Unit. The Attachment Hose should be connected
to the side Air Exhaust Port (19). •
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Canister Cleaner & Attachments
USING THE PORTABLE SHAMPOOER
Before shampooing, vacuum surface thoroughly.
To make suds, turn the Sentria™ system ON and pull
1
the trigger of the Portable Sprayer. A stream of suds
will come out of the cap.
The suds can be sprayed directly onto the surface being
cleaned or on a plain paper bag or in a bowl and then applied
to the surface being cleaned. >
Adjust the Portable Sprayer for proper suds volume by
turning the Spray Adjustment Control located on the
2trigger. >
Work suds into the surface with a soft clean, white
brush or sponge until they disappear. Allow the surface
3to dry completely.
Then vacuum with the appropriate cleaning tool. This
will remove the dry residue which contains grime and
loosened dirt. •
The Portable Shampooer is not recommended for use on upholstery
or fabrics such as silk, brocade and velvet. If in doubt, try a test patch.
Let the test patch dry and then check it before you shampoo further.
/!\ IMPORTANT:
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
PART FOUR
Optional Kirby® Accessories greatly enhance the usefulness
of your new Sentria™ system. In this section, we will discuss
the following:
Using the Carpet Shampoo System
Using Kirby Guard Carpet &
Upholstery Protector
Using the Floor Care System
Using the Turbo Accessory System
Using the Zippbrush
Using the Handi-Butler® Tool
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
CARPET SHAMPOO SYSTEM SET-UP
Vacuum thoroughly before shampooing for maximum
cleaning. Then, remove the Outer Permanent Bag (1) and
the Power Nozzle (25) to prepare for shampooing.
By using the handle, turn the Carpet Shampoo System
Nozzle Belt Lifter to the right (clockwise) until the
green arrows line up. >
1
Slide the slots on the side of the Carpet Shampoo
System Nozzle over the outer shoulders of the Carpet
2Shampoo System Tray. >
While pushing up on the belt with your finger, use
the handle on the Belt Lifter to turn it left (counter•
3clockwise looking at it from the front) until the red
arrows line up. (The Belt Lifter Hook will catch and
stretch the belt.) >
Press the Toe-Touch Control Bottom Pedal (9) all
the way down to raise the front of the Sentria™
system. >
4
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
CARPET SHAMPOO SYSTEM SET-UP (cont)
While sliding the Carpet Shampoo System Nozzle/
Tray Assembly toward the Sentria™ system and over
the Motor Shaft (23), connect the hooks on the bottom
rear of the nozzle to the Attaching Bar (24). >
5
Push the nozzle up against the unit and turn the
Accessory Lock (22) to the right (clockwise) to lock
6the nozzle in place. To engage the belt, use the handle
on the Belt Lifter to turn it all the way to the right
(clockwise) until the green arrows line up. Then lower
the Headlight Hood (21). >
The Shampoo Tank is removable and should be filled
or emptied at your sink.
7
NOTE: The Shampoo Tank is removed and re-attached
in the same way as the Mini Em-Tor® collector (see
page 10 for details).
Unscrew the large cup from the top of the Shampoo Tank
and turn the Suds Control Valve fully to the left (counter•
clockwise) to OFF.
Holding the Shampoo Tank level, fill it to the full line with
warm water (not hot).
Using the large cup from the top of the tank, pour three
cupfuls of Kirby® Carpet Shampoo into the Shampoo Tank.
Do not use more, as over-foaming will result.
NOTE: One tankful of solution will clean about a 10x12
foot carpet (3x3.5m). Larger carpets will require refilling the
Shampoo Tank.
Replace the large cup into the opening on top of the
Shampoo Tank. >
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
CARPET SHAMPOO SYSTEM SET-UP (cont)
Taking care to avoid spilling liquid on the Sentria™
system or the floor, place the opening in the bottom
front of the Shampoo Tank over the Air Exhaust Port
8
(19) on the unit. Angle the Shampoo Tank outward from the
unit until the arrows line up. Next, slide the Shampoo Tank
down over the locking pins on the Air Exhaust Port.
Rotate the Shampoo Tank toward the unit (clockwise) to
lock it in place. >
Push the round elbow of the small flexible hose into
the hole in the tray until it snaps into place. Firmly
insert the other end over the fitting at the bottom front
of the Shampoo Tank. •
9
USING THE CARPET SHAMPOO SYSTEM
To set the nozzle to the proper height, step on the Toe-
Touch Control Upper Pedal (8) as often as necessary to
lower the nozzle to its lowest position. >
1
NOTE: Forcing the brushroll into the surface of the carpet
decreases its ability to thoroughly clean the carpet and could
damage the belt and brushroll.
Turn the Suds Control Valve all the way to the right
(clockwise) to the ON position. Turn the Sentria sys•
2tem ON and engage Tech Drive® power assist (see
page 8 for details). Suds flow will begin immediately.
Control the amount of suds by turning the Suds Control
Valve left (counter-clockwise) for decreased suds flow
and right (clockwise) for increased suds flow. Turning the
valve all the way to the left (counter-clockwise) to the OFF
position will stop the flow of suds completely.
Stopping the flow of suds allows you to thoroughly brush all
the suds into the carpet before applying more suds. This also
lets you spot scrub badly soiled areas. >
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
USING THE CARPET SHAMPOO SYSTEM (cont)
As you move the Sentria™ system back and forth, foam will
be released and the brush will work it into the carpet.
NOTE: Suds should be dispensed the full width of the
tray when the unit is pulled backward. If not, pull back
more slowly or check and clean the Shampoo Tank Filter,
if necessary (see page 35).
After suds have been on the carpet at least five minutes,
pick up the foam by turning the Shampoo Tank to the OFF
position. With the unit at its lowest height level, move the
Shampooer over the foam until the foam is picked up. Some
moisture will accumulate in the front of the tray. Once the
carpet is thoroughly dry, vacuum with the Kirby® Upright. •
CLEANING THE CARPET SHAMPOO
SYSTEM
Push the Toe-Touch Control Bottom Pedal (9) all the
way down to raise the nozzle and tray, then turn the
Sentria system OFF and unplug it. >
1
Turn the Suds Control Valve fully to the left
(counter-clockwise) to the OFF position.
2
Pull the Small Flexible Hose from the Shampoo
Tank. >
Raise the Headlight Hood (21). Release the belt by
turning the Belt Lifter to the left (counter-clockwise)
until the red arrows line up. >
3
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
CLEANING THE CARPET SHAMPOO
SYSTEM (cont)
Turn the Accessory Lock (22) to the left (counter•
clockwise). The Carpet Shampoo System Nozzle/Tray
Assembly will tip forward.
4
Lift the Nozzle/Tray Assembly off the Sentria™ system and
carry it to the sink. >
Remove the hose from the tray and rinse.
5
By using the handle, turn the Belt Lifter to the right
(clockwise) until the green arrows line up. Pull the tray
6and nozzle apart. Rinse tray. >
To clean the brush, push the thumb pads located at
each end of the plastic shield and rotate the shield up
and away from the brush.
7
Disconnect the shield by gently pulling out the ends of the
tray just behind the Brush Roll.
Push the Brush Roll down out of the tray by simultaneously
pushing on both ends of the brush with both thumbs.
Rinse all areas of the shield tray and brush, and remove any
lint from brush tufts.
Shake excess water from the Brush Roll by brushing hand
over the bristles and then drying with a towel. >
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
CLEANING THE CARPET SHAMPOO
SYSTEM (cont)
To remove the Shampoo Tank from the Air Exhaust
Port (19), rotate it away from the Sentria™ system as
8far as it will go, then lift it upwards. >
Remove and clean the Suds Screen Cap, Cup and
Sponge Filter.
9
Rinse out the Shampoo Tank with cold water and
replace the Screen Cap, Cup and Sponge Filter.
NOTE: The belt should not be stretched for extended periods.
Make sure the green arrows on the nozzle line up for storage.
(Remember to align the red arrows before replacing the nozzle
on the unit - see Belt Lifter section on page 10.) •
REPLACING A WORN CARPET SHAMPOO
SYSTEM NOZZLE BELT
To replace the Carpet Shampoo System Nozzle Belt,
push the thumb pads located at each end of the shield
1and rotate the shield up and away from the brush. >
Push down carefully on the ends of the brush with
your thumbs. The brush will snap out and the belt
can be replaced.
2
Be certain the belt is placed in the center of the brush.
NOTE: Use only approved Kirby® belts. >
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
REPLACING A WORN CARPET SHAMPOO
SYSTEM NOZZLE BELT (cont)
Align the metal ends of the brush with the slots on the
tray and push the brush in until it snaps into place. The
brush will only fit the tray the correct way.
3
NOTE: The belt should not be stretched when stored for
an extended period. Make sure the green arrows line up
for storage. •
PROTECT YOUR CARPET AFTER
SHAMPOOING WITH KIRBY GUARD
CARPET & UPHOLSTERY PROTECTOR
Kirby Guard Carpet & Upholstery Protector offers superior
soil protection, giving carpets and upholstery a resiliency
to spills and stains. This helps to reduce maintenance and
allows for easy cleaning, helping carpets and upholstery
to stay cleaner, brighter and fresher longer. Kirby Guard is
CFC (chlorofluorocarbon) and solvent free.
TO USE:
Clean surface to be treated by vacuuming thoroughly
and (in the case of carpet) shampooing. Apply to clean
1carpet, either damp or dry. >
Pour Kirby Guard into the jar for the Portable Sprayer.
Screw the jar tightly on the Portable Sprayer and attach
the Portable Sprayer to the end of the Attachment Hose
in the Blower Mode. (for additional information on using the
Portable Sprayer, refer to p. 25) >
2
Spray evenly with a 50% overlapping spray pattern. >
3
Test for color fastness. Using a clean white cloth, rub Kirby Guard on
a hidden part of carpet or upholstery. If fabric changes color or color
transfers to cloth, DO NOT USE.
Mist may be irritating to the lungs. Avoid breathing vapor or mist. Use
with adequate ventilation. If irritation occurs, move to fresh air. Call a
physician if irritation persists. See botde for a complete list of ingredients.
/!\ IMPORTANT:
/!\ CAUTION:
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
PROTECTING YOUR CARPET (cont)
If Kirby Guard has been sprayed onto any hard sur•
faces such as furniture, baseboards, tile, etc., wipe off
before drying occurs. Allow carpets to dry thoroughly
before resuming normal use. >
4
5
Thoroughly clean the Portable Sprayer after use. •
USING THE KIRBY MIRACLE WAXER®
FLOOR POLISHER
To assemble the roller waxer applicator, attach the top
half of the roller waxer handle to the bottom half (if not
already done). Adjust the upper half until the spring-
loaded pin in the lower half is seated in the hole near the
bottom of the upper half. >
1
NOTE: For very worn areas, two coats may be
required. In this case, multiple thin coats will
KIRBY MIRACLE WAX DIRECTIONS
For Hardwood, Vinyl, Cork and Linoleum Floors:
1. Clean surface thoroughly.
provide better results than one thick coat.
2. Attach Kirby Floor Care System Buffer Nozzle and
Brush according to the instructions on page 39,
under "Floor Buffer Set-Up."
For Marble Floors:
Apply a thin coat and spread as in the directions
in #4. However, buff immediately, avoiding any
drying time.
Once you have completed the steps above, the floor
may be rebuffed, any time it becomes necessary, using
the Floor Care System Buffer Brush. Apply addi•
tional wax ONLY when rebuffing does not produce
acceptable results.
3. For best results, apply a very thin coat of Kirby
Miracle Wax using the roller applicator. It is not
necessary to completely cover the floor with wax at
this time, as the wax will be spread in the next step.
4. Using the Toe-Touch Control Upper Pedal to lower
the nozzle all the way down, spread the wax evenly
over the entire floor using the Kirby Floor Care
System Buffer Brush.
IMPORTANT:
Do not use Kirby Miracle Wax on rubber
5. Let dry 5 minutes.
6. When dry, buff with the Kirby Floor Care System
Buffer Brush.
or asphalt tile.
•
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
USING THE MIRACLE WAXER®
FLOOR POLISHER (cont)
With the wax roller bag facing the hooked end of the
long roller handle, push the wax roller over the connector
on the bottom of the handle until secure. >
2
Pull the roller bag off the wax roller and save the packing
bag. Begin waxing according to the directions in box on
3previous page. >
To remove the wax roller from the long handle, hold the
original wax roller packing bag with the open end facing
4the roller. Push the wax roller into the packing bag as far
as it will go. Avoid touching the wax with your hand. >
Grasp both the packing bag and roller firmly and pull
mem off the long roller waxer handle. To do this, push
5the roller away from the handle grip toward the bar to
compress the retaining spring. This will allow you to
slide the roller over the end cap. Seal bag tightly to prevent pre•
mature drying. Store in the provided packing tube and put in a
safe place away from children and pets until next use. >
If desired, prepare the long waxer roller handle for stor•
age by depressing the spring-loaded pin on the lower
6portion of the handle while pushing the upper portion
toward the hooked end.
IMPORTANT: Seal used roller in original packing bag and
tube after each use to prevent the wax from drying out. •
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
FLOOR BUFFER SET-UP
Your Sentria™ system can be used as an effective floor buf•
fer for wood or tile floors.
To use the Floor Buffer, you must first insert the Buffer
Brush into the Floor Buffer Nozzle.
Center the belt of the Buffer Brush in the middle area
between the tufts of the brush. >
1
Turn the Buffer Nozzle over and slide the ends of the
Brush into the slots at each end of the nozzle. The
2Buffer Brush will only fit the correct way. >
Push the belt up against the Brush Roll with your finger. >
3
While holding the belt in place, use the handle on the
Belt Lifter to turn it left (counter-clockwise) until the
4red arrows line up. The Belt Lifter hook will catch the
belt and stretch it upward into the nozzle. >
To avoid loss of control, do not stand unit on end for polishing. The
Tech Drive pedal must be in the neutral position during polishing
/!\ CAUTION:
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
FLOOR BUFFER SET-UP (cont)
Place the hooks located on the rear of the nozzle over
the Attaching Bar (24) and push the nozzle up against
the Sentria™ system.
5
Turn the Accessory Lock (22) all the way to the right
(clockwise) to lock the nozzle in place. >
To engage the drive belt and Buffer Brush, use the
handle to turn the Belt Lifter all the way to the right
(clockwise) until the green arrows line up. Lower the
6
Headlight Hood (21).>
DO NOT USE Tech Drive® power assist with the
Floor Buffer.
7
Place Tech Drive power assist in Neutral by stepping on
the gray "N" side ("N" for Neutral) of the Tech Drive N/D
Pedal (11). >
USING THE FLOOR BUFFER
Because the unit moves forward when the Floor Buffer
Brush touches the floor, make sure the Buffer Nozzle
is on its highest setting. Press the Toe-Touch Control
Bottom Pedal (9) all the way down to raise the Buffer
Nozzle all the way up.
8
While holding onto the unit's handle, turn the Sentria
system ON. >
To avoid losing control of the Buffer when brush is on the floor surface,
hold on to the handle before plugging the power cord into the wall outlet
and before turning the power switch ON. To avoid possible damage to
soft tiles or marking of waxed and finished non-carpeted floors,
disengage the Tech Drive power assist pedal.
/!\ CAUTION:
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
USING THE FLOOR BUFFER (cont)
Press the Toe-Touch Control Upper Pedal (8) to lower
the brush one notch at a time. Lower the brush as far
as the Toe-Touch Control will allow.
9
With the Buffer running, move the Sentria™ system over
the floor as though you were cleaning a carpet, using slow,
steady strokes.
NOTE: The belt should not be stretched when stored for
an extended period. Make sure the green arrows line up
for storage. •
HARD FLOOR PAD
See page 16 for set-up and use of the Hard Floor Pad. •
USING THE CARPET FLUFFER
Your Kirby® Floor Buffer can also be used as a Carpet
Fluffer to reset the nap on a matted-down carpet.
Before fluffing the carpet, raise the nozzle all the way
up by pushing the Toe-Touch Control Bottom Pedal (9)
all the way down.
1
Place the cleaner on the carpet to be fluffed. >
Plug in the Power Cord. Disengage the Tech Drive®
power assist by pressing on the gray "N" side of the
2Tech Drive N/D Pedal (11).
Holding onto the handle firmly, start the cleaner by pressing
the ON switch. >
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
USING THE CARPET FLUFFER (cont)
Lower the Carpet Fluffer Nozzle one notch at a time
by pushing the Toe-Touch Control Upper Pedal
3(8). The instant the brush contacts the carpet, stop
lowering the brush. >
Then engage Tech Drive® power assist by pressing
down on the red "D" side of the "N/D" Pedal. You are
now ready to fluff the carpet by pushing the cleaner
back and forth over the carpet.
4
NOTE: • Lowering the brush too far on cable yarn type
carpets may cause the carpet to fuzz. Do not fluff
delicate carpets.
• The belt should not be stretched when stored for an
extended period. Make sure the green arrows line
up for storage. •
TURBO ACCESSORY SET-UP
The Turbo Accessory System can be used for a wide variety
of household jobs. It's a sander, a buffing unit, a scouring
unit and a massage unit.
TURBO-SANDING
To set up the Turbo Accessory System as a sander,
unsnap the Sander Dust Shroud at the rear of the tool
and lift off. >
1
Rotate the clamp levers on the side of the Turbo
Accessory upwards to open the clamps. >
2
Be sure no metal objects, such as tacks, nails, etc., are sticking up from
the surface. They can damage the sandpaper and the Turbo Accessory.
They may also cause sparks, which could ignite dust. Replace the
disposable bag after extended sanding because the dust is fine and will
plug the bag pores.
/!\ CAUTION:
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
TURBO-SANDING SET-UP (cont)
Select the correct grade of sandpaper needed for the
job. Use fine paper for a smooth finish and coarse
3paper to clear rough surfaces or remove paint.
Slide the sheet into the front clamp and lock the clamp lever.
NOTE: Three grades of sandpaper come with the Sander.
Each piece is a standard 1/3 sheet. >
Tightly wrap the paper around the bottom of the Turbo
Accessory and tuck the end into the rear clamp. Lock
the rear clamp. >
4
With the Turbo Accessory on a level surface, wrap
the Sander Dust Shroud around the Sander with the
5opening to the rear and snap it closed. >
Insert the Attachment Hose into the end of the Turbo
Accessory.
6
Grip the Sander at the front and rear and turn the
Sentria™ system ON. Then press the ON button on the
top of the Sander.
While applying light pressure, move it over the surface slowly.
Allow the Sander to do the work. Don't force it or lean heavily
on it. The tool works best at high speed. •
Always wear safety glasses when turbo sanding.
/!\ CAUTION:
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
TURBO POLISHING
Attach the synthetic lamb's wool pad using the same
procedure as attaching sandpaper (see page 42). The Turbo
Accessory now becomes a polisher. Use it for polishing hard
waxed surfaces, such as table tops, paneling, and large flat
surfaces. It can be used to polish cars.
The Dust Shroud is not used when polishing. •
TURBO SCOURING
Attach the webbed nylon scouring pad using the same
procedure as attaching sandpaper (see page 42). The Turbo
Accessory now becomes a scouring tool. Use it for scour•
ing hard surfaces such as ceramic tile, etc. (Do not use on
painted surfaces.)
The Dust Shroud is not used when using the scouring pad. •
ORBITAL MASSAGE UNIT
The Turbo Accessory Massage Unit is intended for use where
massage is desired or medically recommended.
To use as an Orbital Massage Unit, attach the soft vinyl pad
to the Turbo Accessory using the same procedure as attaching
sandpaper (see page 42).
The Suction Control Grip can be used to decrease the vibration
of the Massager. Thus, a variable speed Massager. The Suction
Control Grip also enables a person to massage their own back.
The Dust Shroud is not used when using the Turbo Accessory
as a massage unit. •
Do not use the Orbital Massager on swollen or inflamed areas, legs with
varicose veins, areas where there are skin eruptions, unexplained calf pains
or anesthetic skin areas unless first approved by your doctor. Children must
be supervised when using the massager.
/!\ CAUTION:
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
USING THE ZIPPBRUSH
When attached to the Attachment Hose, the Zippbrush can
be used for a wide variety of cleaning surfaces, includ•
ing upholstery, and carpeted steps. It can be used to clean
automotive interiors.
For optimum results, do not press down heavily on the
Zippbrush. Allow the brush to rotate at maximum speed by
gently moving it side to side on the surface being cleaned.
CLEANING THE ZIPPBRUSH
To clean the Zippbrush, press the button on the front
of the brush to release the outer brush ring.
1
When pressing the release button, avoid placing
pressure on the outer ring brush. >
Lift the center Brush/Air Turbine out of the tool and
remove any particles or lint from the brush and turbine.
2Also remove any particles left in the tool cavity. >
Place the Brush/Air Turbine back in the tool and turn
it until the tabs drop into the slots. Hook the tab on the
3rear of the brush ring into the small opening of the tool
and snap it back into place. •
While using the Zippbrush, do not insert fingers into the revolving brush
area or push the release button while the brush is in motion. Keep brush
flat against the surface being cleaned as the brush can throw particles
outward. Do not use on delicate fabrics.
/!\ CAUTION:
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
Handi-Butler® Tool
Important Safety Instructions
The Handi-Butler Model #298906 or #298806 is for use only with the Sentria™ (G10 series)
system. Use only as described in this manual.
Before using this accessory, read and follow the "Important Safety Instructions" and "Warnings"
in the Sentria vacuum cleaner Owner's Manual in addition to the warnings noted below.
WARNING
-
BE FAMILIAR WITH ALL THE IMPORTANT
SAFETY INSTRUCTIONS BEFORE USING YOUR HAND-BUTLER
TOOL. Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
SAVE THESE INSTRUCTIONS
General Safety Rules:
Work Area:
• Keep work area clean and well lit. Cluttered and dark areas invite accidents.
• Do not operate in explosive atmospheres, such as in the presence of flammable liquids,
gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Do not expose to rain or operate in a damp location.
• Keep bystanders, children and visitors away while operating the Handi-Butler tool.
Distractions can cause you to lose control.
Specific Personal Safety Rules:
• Stay alert. Watch what you are doing and use common sense when operating the Handi-
Butler tool. Do not use while tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating may result in serious personal injury.
• Use Safety Equipment. Always wear safety glasses or goggles when using the Handi-
Butler tool. Wear a dust mask for dusty operations.
• Avoid accidental starting. Ensure the switch on the Sentria system and the air vents
on the Handi-Butler tool are in the off position before plugging in. Plugging in tools
that have the switch on invites accidents. Do not leave tool in a dangerous position.
When turning on the cleaner, make sure it is unobstructed.
• After changing tools or making adjustments, make sure the tip of the Flexible Shaft
or Rotator Shaft and any other adjustment devices are securely tightened. Remove
adjustment wrenches before using. A wrench or key left attached to a rotating part
may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better
control of the Handi-Butler tool in unexpected situations.
• Keep hair, clothing, fingers and all parts of body away from openings and moving
parts. Do not wear loose clothing or jewelry. Restrain long hair.
• Secure work. Use clamps or a vise to hold work whenever practical. It's safer than
using your hand and it frees both hands to operate the tool. Allow at least 6 inches
between your hand and the spinning tool.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
Specific Personal Safety Rules (cont.):
• Always hold the tool firmly in your hands.
• Secure Flexible Shaft or Rotator Shaft to the Handi-Butler tool before use.
• Do not reach in the area of the spinning tool on the end of the Flexible Shaft or
Rotator shaft.
• Do not remove the Flexible Shaft or 6" Rotator Shaft while the unit is running.
• Do not touch the spinning parts immediately after use because the tools or tip
might be hot.
• Do not force the Handi-Butler tool. Use the correct tool for your application.
The correct tool will do the job better and safer at the rate for which it was designed.
• Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing the Handi-Butler tool. Such preventive safety measures reduce the
risk of starting the tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the Handi-Butler tool or these instructions to operate the tool. Power tools are
dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool's operation.
If damaged, have the power tool repaired before use. Many accidents are caused
by poorly maintained power tools.
• Use the Handi-Butler tool, accessories and tool bits, etc., in accordance with these
instructions and in the manner intended for Handi-Butler tool, taking into account the
working conditions and the work to be performed. Use of the Handi-Butler for operations
different from intended could result in a hazardous situation.
• The use of any other accessories not specified with this product may create a hazard.
• Do not alter or misuse the tool. These tools are precision built. Any alteration or
modification not specified is misuse and may result in a dangerous condition.
• Do not leave the tool running or unattended. Turn power off when not in use.
• Do not use drill bits or cutting tools with the Handi-Butler tool. Use only genuine
Kirby® Parts.
Service:
• Have your Handi-Butler tool serviced by an authorized Kirby Distributor using only
identical replacement parts. This will ensure the safety of the Handi-Butler tool
is maintained.
The Handi-Butler tool operates at 18,000 maximum RPM.
Vibration Level
m/s2 - EN ISO 5349
8.5
Sound Pressure Level
LpA - EN ISO 3744
84, 5 dB(A)
Guaranteed Sound Power Level
LwA - EN ISO 3744
98 dB(A)
FOR HOUSEHOLD USE ONLY
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
FUNCTIONAL DESCRIPTION
The Handi-Butler tool is an air-powered rotary tool that can be used for a wide variety of fine,
detailed cleaning and polishing tasks. It can be used as a hand-held tool or as a stationary,
table-top tool.
The Handi-Butler tool includes:
A
B
C
D
E
F
Handi-Butler Tool
Flexible Shaft
Rotator Shaft
Angled Key
G
H
I
Mounting Cradle
Polishing Compound (not shown)
Lockout Bar
Mini Wrench
Safety Glasses
Cleaning & Polishing Tools
Recommended Uses
J
Screw Mandrel
Small Screw Mandrel
Conical Felt Tip
1/2" Felt Tip
Used with felt polishing tips
Used with polishing disks
K
L
M
N
0
Polish plastics, metals, jewelry
Polish plastics, metals, jewelry
Polish plastics, metals, jewelry
Polish plastics, metals, jewelry
Cleans silverware and jewelry
Cleans silverware and jewelry
Removes rust or for polishing metal
1" Felt Disk
1" Cloth Disk
P
Cup Bristle Brush
Wheel Bristle Brush
Carbon Steel Brush
Q
R
The Handi-Butler tool (A) should be used with the Tech Drive®
power assist pedal in Neutral.
/!\ IMPORTANT:
/!\ NOTICE:
When using polishing compound, protect the work surface and
surrounding area by using drop cloths. Wear work clothes to avoid
damage to clothing. Do not use the polish over carpeting.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
USING THE HANDI-BUTLER TOOL IN THE
HAND-HELD MODE
The Handi-Butler Tool Hand-Held Mode gives the user
maximum flexibility when cleaning and polishing an item.
To use the Handi-Butler tool in the hand-held mode,
begin with the hose attached to the front of your
Sentria™ system. >
1
For ease of use, attach the bit to the Flexible Shaft (B)
before assembling the Handi-Butler tool.
2
Rotate the tip of the Flexible Shaft (B) until the hole in the tip
lines up with the hole in the grip section. Insert the long end
of the Angled Key (D) into the holes. >
Use the enclosed Mini Wrench (E) to loosen the silver
rotating tip at the end of the Flexible Shaft (B). >
3
Do not bend the Flexible Shaft (B) to a radius less than 2 inches,
it will over heat and fail.
/!\ WARNING:
Do not remove end ferrule while tool is running.
/!\ WARNING:
/!\ CAUTION:
Safety Glasses (F) should be worn when using the Handi-Butler tool.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
Select one of the cleaning or polishing tools and insert
into the tip of the Flexible Shaft (B). Firmly tighten the
tip to secure the tool in place with the Mini Wrench (E) .
Remove the Angled Key (D). >
4
NOTE: The Angled Key (D) must be inserted into the holes
in order to attach or remove a polishing or cleaning tool.
Now you are ready to attach the Handi-Butler tool to
your Sentria™ system. Firmly twist the Handi-Butler
tool (A) on to the end of the hose. >
5
Screw the silver end of the Flexible Shaft (B) onto
the Handi-Butler tool (A) making sure the prong in the
6center of the Flexible Shaft fits into the center of the
Handi-Butler tool. >
To avoid accidental starting, make sure the air inlet
openings on the Handi-Butler tool (A) are CLOSED
before turning your Sentria system on.
7
Then, turn your Sentria system on. To start the Handi-Butler
tool, rotate the Air Valve of the Handi-Butler tool to expose
the two air inlet openings. You are now ready to gently pol•
ish and clean. Allow the speed of the tool to do all the work.
Avoid putting excessive pressure on the spinning tool. •
To avoid accidental starting, make sure the air inlet openings on
the Handi-Butler tool (A) are CLOSED before turning your
Sentria system on.
/!\ IMPORTANT:
/!\ NOTICE:
USE GENTLE PRESSURE when using the Handi-Butler tool. Strong
pressure could stop the rotation of the tool break the cleaning or polishing
tool or result in damage to the item being cleaned or polished.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
USING THE HANDI-BUTLER TOOL IN THE
TABLE-TOP MODE
The Hand-Butler tool table-top mode allows you to hold the
item you wish to polish or clean with two hands for better
control.
In the Table-Top mode, the cleaner should be securely
fixed in the Handi-Butler Mounting Cradle (G) to prevent
the cleaner from moving on the work surface. The cradle
1
should be bolted (using the provided holes as shown using
1/4" or M6 bolts, washers and nuts) to a stable surface.
Convert your Sentria™ system to the Portable mode. Make
sure that the Tech Drive® pedal is in Neutral. Then, with the
power off and the nozzle removed, carefully lift the unit and
place onto the cradle. >
The rear of the unit should be firmly seated in the
depression of the cradle, with the rear wheels raised
from the work surface and the front of the unit raised to
its highest position. >•
2
Attach the Air Intake Guard (included with your
Sentria system) to the front of the unit. >
3
Attach the Handi-Butler tool (A) to the Air Intake
Guard. >
4
To reduce the risk of injury to the operator, insure that the Handi-Butler
toll is properly secured before use.
/!\ CAUTION:
Some dust created by polishing and cleaning could contain chemicals known to cause cancer, birth
defects or other reproductive harm.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to filter out microscopic particles.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
Now you are ready to attach a tool to the 6" Rotator
Shaft. Rotate the tip of the Rotator Shaft (C) until
the hole in the tip lines up with the hole in the grip
section. Insert the long end of the Angled Key (D)
into the holes. >
5
6
7
Use the enclosed Mini Wrench (E)to loosen the silver
rotating tip at the end of the Rotator Shaft (C). >
Select one of the cleaning or polishing tools and insert
into the tip of the Rotator Shaft (C). Firmly tighten the
tip to secure the tool in place with the Mini Wrench (E).
Remove the Angled Key (D). >
Screw the end of the Rotator Shaft (C) onto the
Handi-Butler tool (A) making sure the prong in the
8center of the Rotator Shaft fits into the center of the
Handi-Butler tool. >
To avoid accidental starting, make sure the air inlet
openings on the Handi-Butler tool (A) are CLOSED
before turning your Sentria™ system on.
9
Turn your Sentria system on. Then, rotate the Air Valve on
the Handi-Butler tool (A) to expose the two air-inlet open•
ings. You are now ready to gently polish and clean. Allow
the speed of the tool to do all the work. Avoid putting exces•
sive pressure on the spinning tool. •
Download from Www.Somanuals.com. All Manuals Search And Download.
52
Optional Accessories
MAINTENANCE
Kirby recommends that all tools be serviced by an authorized
Kirby Distributor.
The polishing tips and brushes in the Handi-Butler tool have
been designed for many hours of use. Check them regularly
for wear and replace when necessary. Only genuine Kirby®
Handi-Butler® tool parts should be used.
Oil the flexible shaft by dripping 3-4 drops of oil along
the drive shaft after every ten uses. •
1
CHANGING THE ACCESSORIES
Your Handi-Butler tool comes with a variety of polishing
and cleaning tools that can be easily changed to meet your
cleaning needs.
The brushes come pre-assembled. The tools used with the
polishing tips and disks will need to be assembled before use.
PADS FOR USE WITH THE SCREW MANDREL
The Conical Felt Tip (L) and the 1/2" Felt Tip (M) can
easily be screwed onto the Screw Mandrel (J). •
1
PADS FOR USE WITH THE SMALL SCREW MANDREL
The Small Screw Mandrel (K) is designed for use with
the 1" Felt Disk (N) or the 1" Cloth Disk (O). To attach a
1disk, use the handle end of the Mini Wrench (E) to
remove the small screw from the end of the mandrel. >
Put the polishing disk between the two small red
washers found on the Small Screw Mandrel (K) and
2place the washers and the disk on the screw. Reinsert
the screw into the Mandrel. Use the Mini Wrench (E) to
tighten it securely. •
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
LOCKING OUT THE HANDI-BUTLER TOOL®
When leaving the Handi-Butler tool in the table-top mode
unattended, it is recommended that the user lock out the tool to
prevent accidental starting or access to the tool by children.
With the unit securely seated in the Mounting Cradle (G),
insert the tines of the Lockout Bar (I) in to the slots at the base
of the On-Off pedal of the Sentria unit. Then, slide the hole on
the Lockout Bar over the eyelet on the Mounting Cradle. The
user can then place a combination lock (not provided) through
the eyelet to securely lock the Handi-Butler tool and prevent it
from running until the lock is removed. •
Operating/Maintenance Tips
PART FIVE
Your Kirby® Sentria™ system is a highly sophisticated
home maintenance system. As with most modern appliances,
it requires a modest degree of routine maintenance to keep
it operating efficiently. This section of the Owner's Manual
presents tips on operating and maintaining your Sentria sys•
tem. In this section, we will discuss the following:
Changing the Power Nozzle Belt
Adjusting the Brush Roll for Optimum
Performance
Miscellaneous Parts Replacement
Helpful Answers to Questions/
Troubleshooting
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating/Maintenance Tips
CHANGING THE POWER NOZZLE BELT
After extended use, the Power Nozzle Belt on your Sentria™
system may become stretched and worn causing the belt to
slip.(See page 11 - Brush Roll Performance Indicator Light.) If
this condition exists, simply replace the old belt with a new one.
NOTE: Use only approved Kirby® belts.
To change the belt, remove the nozzle from the Sentria
system. Then release the belt tension by using the han•
1dle on the Belt Lifter (20) to turn it all the way to the
right (clockwise) until the green arrows line up. >
Unlock the Rug Plate (26) by unhooking the two latches
on the rear of the nozzle. >
2
Pull on the rear edge of the Rug Plate to remove from
the nozzle.
3
Note the Brush Roll Bristle Height Adjustment setting
(1, 2, or 3).
Lift out the Belt and Brush Roll. >
Slide off the old belt and replace with a new one.
4
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating/Maintenance Tips
CHANGING THE POWER NOZZLE BELT (cont)
Make sure the Brash Roll Bristle Height Adjustment
setting (1, 2, or 3) is the same on both ends as when the
5brush was removed. See below for discussion of the
Brush Roll Bristle Height Adjustment (1, 2, or 3). Place the
belt and Brush Roll back into the nozzle. One of the plastic
Brush Roll ends is larger than the other, thus the Brush Roll
will only fit in the nozzle one way.
Then center the belt on the Brush. >
Replace the Rug Plate by placing it on the front of the
bumper first and then pulling it over the bumper on
the rear of the Power Nozzle (25). Secure the Rug Plate
6
using the two latches that hold it in place. >
Using the handle on the Belt Lifter (20), turn it to the
left (counter-clockwise) until the red arrows line up.
7This will stretch the belt in preparation for returning
the nozzle to the Sentria™ system.
Now you are ready to re-attach the Power Nozzle and
re-engage the belt. •
ADJUSTING THE BRUSH ROLL HEIGHT
The Brush Roll bristles wear away after long periods of use.
This reduces cleaning efficiency.
However, the ends of the Brush Roll are adjustable, so you can
extend the bristles, allowing the brush to work like new again.
The Brush Roll on a new Sentria™ system has three settings:
one notch, two notches and three notches. The greater the num•
ber of notches, the farther the bristles are extended. Use the one
notch (1) setting for delicate carpeting such as berber. Use the
two-notch (2) and three-notch (3) settings to extend the bristles
to compensate for bristle wear. >
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating/Maintenance Tips
ADJUSTING THE BRUSH ROLL HEIGHT (cont)
Remove the Power Nozzle (25) from the Sentria system. >
1
Release the belt tension by using the handle on
the Belt Lifter (20) to turn it all the way to the right
(clockwise) until the green arrows line up.
2
Unlock the two latches on the rear of the Power Nozzle to
remove the Rug Plate (26).
Then lift the brush out of the nozzle. >
Rotate the plastic Brash Roll ends to the 1,2 or 3-notch
settings as desired. The greater the number of notches,
the farther the bristles are extended.
3
When viewed from the top, rotate the plastic Brush Roll ends
to the side with the appropriate number of notches visible.
Make sure both plastic Brush Roll ends are set to the same
number of notches. >
Place the brush back into the nozzle making sure both
plastic Brush Roll ends are set to the same number of
4 notches (1, 2, or 3).
Replace the Rug Plate by placing it on the front of the bum•
per first and then pulling it over the bumper on rear of Power
Nozzle (25). Secure the Rug Plate using the two latches that
hold it in place.
Using the handle, hook the belt onto the Belt Lifter (20) and
turn the Belt Lifter to the left (counter-clockwise) until the
red arrows line up. This will stretch the belt in preparation
for returning the nozzle to the Sentria™ system. •
Keep the entire Brush Roll and belt track clear of lint, string,
hair and other fibers. This will allow the Brush Roll to perform
to its fullest potential.
SERVICE TIP:
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating/Maintenance Tips
Miscellaneous Parts Replacement
WHEEL WEAR/ REPLACEMENT
Kirby® wheels are made with a pliable tread that is designed
to prevent carpet wear and prevent damage to non-carpeted
floors. After extended periods of use, the tread on the wheels
will wear out and the wheels will need to be replaced.
Check wheel tread occasionally to determine if the wheels
need to be replaced. The tread material is lighter in color
than the plastic wheel itself. If any of the darker plastic
wheel is showing through the tread, the wheels need to be
replaced. The wheels are not user-replaceable. Contact your
nearest authorized Kirby Service Center for prompt, courte•
ous wheel replacement. •
CORD REPLACEMENT
If the electrical cord connecting the Sentria™ system to the
outlet becomes cut or frayed over time, DO NOT USE THE
UNIT. Contact your authorized Kirby Service Center imme•
diately for replacement.
Avoid damage to your cord by being careful not to run over it
with your Sentria system. Also, unplug your unit by grasping
the plug at the end of the cord rather than pulling on the cord
itself. •
HEADLIGHT REPLACEMENT
If one or more of the three LED lights in your Headlight
Assembly burn out, please contact your authorized Kirby®
Distributor for replacement. •
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating/Maintenance Tips
Questions and Answers/Troubleshooting
Q WHAT IS A DOUBLE-INSULATED MACHINE? (Servicing of double-insulated appliances)
A In a double-insulated appliance, two systems of insulation are provided instead of ground•
ing. No grounding means is necessary on a double-insulated appliance, nor should a means for
grounding be added to the appliance. A double-insulated appliance is marked with the words
"DOUBLE-INSULATED" (U.S.A. and Canada). The symbol • (square within a square) may
also be marked on the appliance.
Servicing a double-insulated appliance requires extreme care and knowledge of the system
and should be done only by qualified service personnel.
Replacement parts for this double-insulated Sentria™ model must be genuine Kirby®
parts for maintenance of safety and protection of warranty.
Q WHAT SHOULD I DO IF THE MOTOR DOES NOT RUN WHEN I TURN
THE Sentria SYSTEM ON?
A Many service calls are unnecessary. Checking a few simple things can save a lot of cost,
time and trouble. Whenever your Sentria system does not perform properly, make these
checks first before calling authorized service personnel.
IF THE MOTOR DOES NOT RUN WHEN THE MOTOR ON-OFF SWITCH IS PUSHED:
1. Make sure the Power Cord is plugged into an outlet and that the outlet has power.
(Check for a blown fuse, tripped circuit breaker or power company trouble.)
2. Make sure the cord plug is fully inserted into the unit.
3. Look for breaks in the Power Cord insulation. If the cord is damaged, get a new one.
DO NOT ATTEMPT TO REPAIR IT. Use only a genuine Kirby Power Cord. Do not use
standard extension cords.
4. Make sure that an attachment or accessory is properly mounted on the front of the
Power Plant. The unit will not run without the Power Nozzle(25), Hose Coupling,
Air Intake Guard or Accessory Brush Nozzle in place.
5. The unit will not operate without either a Filtration Bag Assembly/ Mini Em-Tor® collector (6),
Attachment Hose or Carpet Shampoo Tank properly installed on the Air Exhaust Port (19).
6. The Filtration Bag Assembly/Mini Em-Tor collector, Attachment Hose or Carpet Shampoo
Tank must "click" firmly into place for the unit to operate. If the fitting is too tight and
you have difficulty installing the above, apply a small drop of water to the gasket to
reduce friction and ease installation.
Q WHAT SHOULD I DO IF THE Sentria SYSTEM DOES NOT PICK UP LINT
OR DIRT ON THE CARPET?
A 1. Check to see if the Brush Roll is turning, when the Sentria system is running.
2. If the Brush Roll is not turning freely, the belt is slipping, broken or not on the Motor Shaft (23).
3. If the belt is not on the Motor Shaft (23), remove the nozzle and follow the instructions on
pages 11. See page 56 for bristle extension.
4. If the belt is in good condition and the brush is running, check for bristle wear and replace
Brush Roll, if necessary.
To check for wear, turn the Power Nozzle (25) over and place a ruler against the metal Rug
Plate. If the bristles are below or just touching the ruler, the Brush Roll should be
adjusted. See page 56 for details.
5. Make sure that the nozzle height is adjusted to place the brush in contact with the carpet.
Use the Toe-Touch Control to adjust as appropriate. See page 8.
6. Check the bag to see if it is full.
7. Check the fill tube for clogging.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating/Maintenance Tips
Questions and Answers/Trouble shooting
Q I SMELL BURNING RUBBER WHEN I USE MY Sentria™ SYSTEM
WHAT SHOULD I DO?
A 1. Check to see if the Brash Roll is turning when the Sentria system is running. If not, then
the Brush Roll may be stalled due to threads around the ends. Remove Brush Roll and
make sure it rotates freely at both ends. (See page 54.)
2. The belt may not be fully engaged (or disengaged). Make sure the green arrows or red
arrows on the Belt Lifter (20) match up fully.
3. If a slipping belt has deposited a black residue on the Motor Shaft (23), remove it gently
using steel wool or sandpaper and replace the belt.
Q HOW DO I VACUUM MY MATTRESS?
A 1. Remove all bedding, including mattress cover, from the mattress.
2. Convert your upright Sentria system to a Portable Cleaner. See "Portable Cleaning"
on page 16.
3. Place Portable Cleaner on the mattress.
4. Disengage Tech Drive® power assist by pressing the gray "N" side (marked "N" for
Neutral) of the N/D Pedal (11).
5. Disengage the Brush Roll.
6. Plug in your Sentria system and turn it ON.
7. Lower the Power Nozzle by pressing the Toe-Touch Control Upper Pedal (8) until it is
all the way down.
8. Begin vacuuming.
Q HOW DO I VACUUM MY CARPETED STAIRS?
A There are several different ways. You can use:
• the Portable Cleaner. (See page 16.)
• the Zippbrush. (See page 45.)
• or the Upholstery Nozzle. (See page 21.)
Q HOW DO I CLEAN UNDER MY BED?
A Your Sentria system can be used in the canister mode (see page 19) with the Surface
Nozzle to vacuum under the bed and other low furniture.
Always exercise caution when vacuuming stairways.
IMPORTANT:
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating/Maintenance Tips
Questions and Answers/Troubleshooting
Q HOW DO I VACUUM MY UPHOLSTERED FURNITURE?
A 1. Convert to a canister. (See page 19.) (Do not use Power Nozzle (25) on furniture.)
2. Use the Attachment Hose with or without the following attachments:
• the Upholstery Nozzle.
• the Crevice Tool with the brush removed. (Use in between seat cushions and in crevices.)
• the optional Zippbrush.
The optional Zippbrush uses rotating brushes to agitate fibers and remove imbedded dirt and
pet hair from the fabric. When using the Zippbrush, move it slowly from side to side across
surface. Do not apply heavy pressure as it will slow the brush action. (If the brush becomes
jammed and stops turning, simply rotate the inner rotating brush clockwise to free it up and let
go. It should then resume turning.)
To clean hard-to-reach upholstery buttons, use narrow tip of the Zippbrush, located on the side
opposite the hose, to work the dirt loose. (For additional information on the use and maintenance
of the optional Zippbrush, see the Zippbrush section on page 45).
Q HOW DO I CLEAN MY WALLS AND CEILING?
A 1. Convert to a canister. (See page 19.)
2. Attach one or two Extension Tubes to the Attachment Hose by inserting the hose into the
Extension Tube opening and twisting to lock in place.
3. Attach the Suction Control Grip onto the end of the Extension Tube.
4. Attach the Wall & Ceiling Brush to the end of the Suction Control Grip. The Suction
Control Grip not only allows you to regulate airflow, it also allows you to adjust the Wall
& Ceiling Brush to the proper angles for mantles, window ledges, walls and ceilings.
Q HOW DO I CLEAN MY CAR ?
A Your Sentria™ system comes equipped with a range of tools to help you clean your car.
In addition, you may also use the optional Zippbrush for vacuuming automobile upholstery,
carpeting, floor mats and trunks. (See Zippbrush section on page 45 for Zippbrush use and
maintenance information.)
1. Convert to a canister. (See page 19.)
2. You can use the end of the Attachment Hose for straight suction or attach any one of
a variety of tools.
3. We suggest using the Upholstery Nozzle (or optional Zippbrush) to clean the seats, areas
under the seats and the trunk.
4. Use the Crevice Tool (with or without the small Crevice Tool brush end) for small,
hard-to-reach areas, such as the area between the windshield and dash and the area
between the seats.
5. Use the Duster Brush to clean the instrument panel.
6. Use the Massage Cup to pick up gravel and heavy particles on floor mats and carpeting.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating/Maintenance Tips
Questions and Answers/Troubleshooting
Q HOW DO I CLEAN OTHER HOME FURNISHINGS?
A Books and Bookcases:
1. Convert to a canister. (See page 19.)
2. Attach the Duster Brush to the end of the Attachment Hose and "dust" the books and bookcase.
3. Other options include using an Extension Tube with the Duster Brash or the Wall &
Ceiling Brush to dust the bookcase top.
Lampshades and Pictures:
1. Convert to a canister. (See page 19.)
2. Attach the Duster Brush to the Suction Control Grip. Then connect the grip to the Attachment
Hose. Test the airflow by regulating the Suction Control Valve on the Suction Control Grip
before you dust your lampshades. Dust glass-covered artwork and picture frames.
Stereos and Computers:
1. Convert to a canister. (See page 19.)
2. Attach the Duster Brush to the Suction Control Grip. Then connect the grip to the
Attachment Hose. Test the air-flow by regulating the Suction Control Valve on the Suction
Control Grip before you dust your home electronics.
3. Connect the Inflator/Deflator tool to the end of the Attachment Hose to dust between the
keys on a computer key board, faceplates on electronic gear and other hard-to-reach
small spaces.
Wicker Furniture and Baskets:
1. Convert to a canister. (See page 19.)
2. Attach the Duster Brush to the end of the Attachment Hose. Your Duster Brush works well
between cracks and crevices on wicker and other irregular surfaces.
Drapes and Blinds:
1. Convert to a canister. (See page 19.)
2. For drapes, attach one or two Extension Tubes to the Attachment Hose. Connect the
Suction Control Grip to the Extension Tube and then connect the Upholstery Nozzle (with
the faceplate attached). Test the air-flow by regulating the Suction Control Valve on the
Suction Control Grip before you dust your drapes and blinds.
The Suction Control Valve on the Suction Control Grip regulates airflow and prevents you
from pulling the drapes off the curtain rods.
For blinds, follow a similar procedure using the Duster Brash instead of the Upholstery
Nozzle. If using the Suction Control Grip, make sure to completely close the Suction Control
Valve to maintain maximum airflow.
Q WHAT SHOULD I DO IF MY FILTER BAG SMELLS?
A Change it. Replace the disposable bag when the dirt reaches the fill line. Do not overfill.
1. You may also purchase Odorific® II, an odorizer that leaves your room smelling clean and
fresh. Place a few drops on a cottonball and toss it in the Outer Permanent Bag. For a list
of other fine Kirby® products, (see page 64 and 65.)
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Relations
Got a Question? Need Assistance?
Your local authorized distributorship is available to answer any questions
regarding your purchase or the operation of your Sentria™ Home Care
System.
The Kirby Company also has Consumer Relations Specialists available to
answer any questions you may have about the Sentria Home Care System or
provide you with the name of your nearest Kirby distributor.
You can contact USA Consumer Relations by:
e-mail
telephone
fax
1-800-494-8586
216-529-6146
mail
Consumer Relations
1920 West 114th Street
Cleveland, Ohio 44102
Our office hours are 8:00 a.m. to 5:00 p.m. Eastern Time, U.S.A.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Kirby® Home Care Products
From Your Factory Authorized Distributors and Service Centers
ALLERGEN CONTROL PRODUCTS
MicroAllergen Filter Bags
Traps 99.97% of particles as small as 0.3 microns. Rated HEPA 11. Minimizes bag odor.
Allergen Control Shampoo
Neutralizes dust mite particles. Reduces allergens caused by pollen. Cleans and brightens carpets.
Kirby Guard Carpet & Upholstery Protector
Minimizes dirt penetration to keep carpets cleaner, longer. Helps to keep spills from seeping
in. Nontoxic and safe for people and pets.
Multi-Allergen Control Spray
Neutralizes allergens on contact. Great for spraying mattresses and upholstery.
Microfiber Cloth
Use when dusting. 30 times finer than cotton. Absorbs 4 times its weight in liquid, dirt and
grime. Washable.
CARPET SHAMPOO PRODUCT FAMILY
Carpet Shampoo
Highly effective product for deep-cleaning carpets and rugs. Carpet-safe and non-toxic.
Multi-Purpose Spot Remover
Ready-to-use formula for everyday stains. Just spray on stain and blot with a clean, white
cloth. Great for use prior to shampooing.
Pre-Treatment for Heavy Traffic Areas
Highly effective formula gives you a "head start" on shampooing. Just spray on heavily-soiled
walkways, entryways and traffic patterns a few minutes prior to shampooing.
Carpet Cleaning Kit
The perfect partner for your carpet! Everything you need to deep-clean your carpets in three
easy-to-use products. One quart of Carpet Shampoo and one 12-oz. bottle each of Spot Remover
and Pre-Treatment. All three products yield best results when used in combination.
STAIN REMOVER PRODUCT FAMILY
Kirby Foam
Effective on heavily-soiled carpeted stairs and other hard-to-reach places. Just spray and blot.
Great for auto and home floor mats!
Pet Stain & Odor Carpet Cleaner
Attacks nasty pet stains and odors with natural enzymes. Active ingredients get right to the core
of carpet's fibers, ensuring that lingering odors are eliminated and that pets won't return to the
same spot.
Grease & Oil Stain Carpet Cleaner
Penetrates and removes the toughest stains... auto grease, garage and cooking oils and more.
Just spray and blot.
Food Stain Carpet Cleaner
Specially formulated cleaner with natural enzymes that work to break the chemical bonds of
tough food stains, grape juice, red wine, chocolate, ketchup and more.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Kirby® Home Care Products
From Your Factory Authorized Distributors and Service Centers
HARD SURFACE PRODUCT FAMILY
Scuttle® Glass & Surface Cleaner
A traditional Kirby favorite; great for hard surfaces such as countertops, appliances as well as
windows, mirrors and more. Dries to a streak-free shine.
Citrus Scuttle
Heavy-duty cleaner for all types of indoor and outdoor surfaces. Great for ovens, grills,
machinery and work areas.
Lickity Split
All-purpose dissolver works better than any goo remover on the market. Use it to dissolve tape,
glue, gum, stickers, asphalt, lipstick, crayon, oil, tar, adhesives, permanent marker and more.
HOME FRAGRANCE PRODUCT FAMILY
HomeFresh Room and Carpet Freshener
Leaves carpets and rooms smelling pleasantly fresh while eliminating odors. Just sprinkle on
carpets and vacuum after a few minutes. Available in 5 fresh fragrances.
Odorific® II Deodorizer
All-purpose liquid deodorizer. Great for areas with foul odors like trash cans and damp-corners.
A few drops is all you need. Also, a few drops are great for deodorizing your vacuum's outer
cloth bag. Fresh fragrance lingers for many hours.
OTHER FINE KIRBY PRODUCTS AND SUPPLIES
Extendable Crevice Tool
Clean under refrigerators, low furniture, and radiator vents. 5-piece tool set lets you continue
to add pieces until you reach the desired length.
Mini Attachments
This set includes a mini hose and 5 mini attachments that are great for small detail cleaning.
Get into cracks and crevices on computer keyboards, figurines, dashboards, and pianos.
Splitsecond® Portable Hand Vacuum
This cordless portable hand vacuum can be used where cord-type cleaners cannot reach.
Comes complete with handy re-charging unit so it's always ready for use.
Splitsecond 2® Automotive Vacuum
The twelve-volt automotive version of the popular Splitsecond portable hand vacuum plugs
into a standard cigarette lighter. Perfect for cars, boats, campers and recreational vehicles.
Contact Your Factory Authorized Location for these and other Kirby Home Care Products.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
set-up
using
25
26
E
About this Manual
4
29
19
23
19
18
19
21
20
20
24
22
22
20
21
21
Extension Tubes
20
Power Nozzle
Accessories
F
changing the belt
54
Accessory Lock
Air Intake Guard
Attaching Bar
disengaging Brush Roll. . . . 15
Floor Buffer
39
39
set-up
height setting
lowering
8
8
using
G
40
Attachments
raising
8
Attachment Hose
Crevice Tool
removal
19
54
54
14
Getting Started
6
Rug Plate
Brush Roll
Duster Brush
H
Handle
Extension Tubes
Inflator/Deflator
Massage Cup
Power Switch
Attaching Portable Handle . 16
Handle Tilt Latch
Q
7
Suction Control Grip
Surface Nozzle
Upholstery Nozzle
Wall & Ceiling Brush
Questions & Answers
59
54
Handle Release Button . . . . 16
removing Upright Handle . . 16
R
Handi-Butler® Tool
Changing Accessories
46
52
Replacement Belts
S
B
Bag
Functional Description . . . . 47
Safety Instructions
2
17
15
22
20
Hand-Held Mode
Maintenance
48
52
46
50
16
19
Stair Cleaning
Assembly-removal
Bag Release Button
Bag Support Strap
Changing Bags
10
16
10
9
Straight Suction Cleaning
Suction Control Grip
Surface Nozzle.
T
Safety Instructions
Table-Top Mode
Hard Floor Pad
Hose -installing
Disposable Filter Bags . . . .
9
Tech Drive® Power Assist
I
Outer Permanent Bag . . . . 10
description
8
8
Top Adaptor
Belts
Changing Belts
Belt Lifter
Blower
set-up
9
Inflator/Deflator Tool
24
ON/OFF Pedal
Turning off
K
8
54
10
Turning on
8
Kirby® Carpet Shampoo . . . . 31,64
Tilt Latch Lock
Toe-Touch Control
Turbo Accessory System
clamp levers
Dust Shroud
massage
7
M
7
Maintenance tips
53
22
17
15
10
23
24
42
42
43
44
44
43
43
44
42
Massage Cup
using
Mattress cleaning
Brush Roll
Micron Magic® filtration
Mini Em-Tor® collector
adjusting for optimum
performance
56
56
11
polishing
Miracle Waxer® floor polisher.. 37
height adjustment
indicator light
rear clamp
Miscellaneous Parts
Replacement
58
sanding
C
scouring
Moving your machine
7
set-up
Canister Cleaner
Carpet Fluffer
Carpet Shampoo System
cleaning
18
41
30
33
35
30
32
30
32
7
O
U
Operating Tips
53
29
4
Upholstery Nozzle
21
14
16
Optional Accessories
Owner's Manual-using
Upright Cleaner
replacing the belt
set-up
Upright Handle-removing
P
W
Suds Control Valve
tray
Portable Cleaner
Portable Handle
Portable Shampooer
set-up
16
16
Wall & Ceiling Brush
21
Z
using
Zippbrush
Carrying your machine
Cleaning products
Crevice Tool
27
28
Turbine
45
45
45
45
64
21
using
cleaning
Portable Sprayer
Outer Brush Ring
using
D
adjusting spray
cleaning
Dip Tube
Jar
26
26
26
25
Disposable Filter Bags
9
Duster Brush
20
66
Download from Www.Somanuals.com. All Manuals Search And Download.
C€ DECLARATION OF CONFORMITY
We, Kirby, declare under our sole responsibility that, where applicable,
the Kirby Model G10E Vacuum Cleaner is in conformity with the
following standards or standardized documents.
IEC 60335-1 (EN 60335-1), IEC 60335-2-2 (EN 60335-2-2),
EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 and EN 50366
in accordance with the regulations including the Low Voltage Directive
73/23/EEC, 93/68/EEC and EMC Directive 89/336/EEC
C€ 95
KIRBY
1920 West 114th Street • Cleveland, OH 44102 • U.S.A.
Made under one or more of the following patents and design registrations,
other patents and design registrations pending.
United States
Australia
582715
Mexico
175879
4692754
4728942
4877432
4905343
4947512
5007133
5014387
5047597
5057131
5064455
5086536
5092915
5115537
5187832
5285550
5308288
5335740
5573369
5713810
5784750
5792224
D392779
D396902
610422
Netherlands
0233933
616833
633948
640711
New Zealand
236192
661597
Norway
169940
175085
Austria
0233933
Belgium
0233933
South Africa
S.A. Patent No. 90/5400
S.A. Patent No. 93/5427
Benelux
0233933
South Korea
75716
France
0233933
Sweden
0233933
Germany
Geschutztes Muster
M9002507.5
P3650439.4-08
68916013.5
Switzerland
0233933
United Kingdom
U.K. Patent 0233933
U.K. Patent 0399031
U.K. Patent 2229651
U.K. Reg. 2005900
Italy
0233933
Canada
1271006
2016600
2036739
Japan
1997813
2011083
Luxembourg
0233933
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Sentria™
No.
1
Part
Outer Permanent Bag
2
Bag Latch Tab
3
Disposable Filter Bag
Bag Support Strap
Top Adaptor
4
5
6
Mini Em-Tor® Collector
Performance Indicator Light
Toe-Touch Control Upper Pedal
Toe-Touch Control Bottom Pedal
Handle Tilt Latch
Tech Drive Power Assist Neutral Pedal
Tech Drive Power Assist Drive Pedal
Power Switch
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Handle Release Button
Portable Handle
Bag Release Button
Upright Handle
Carrying Grip
Air Exhaust Port
Belt Lifter
Headlight Hood
Accessory Lock
Motor Shaft
Attaching Bar
Power Nozzle
Bumper
Accessories and Attachments
27
28
Carpet Shampoo System Shampoo your carpet.
Floor Care System
Hard Floor Pad
Floor buffer for wood or tile floors. Carpet fluffer to
reset the nap on a matted-down carpet.
29
Dust bare floors.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories and Attachments
No.
30
Part
Recommended Uses
Kaddy
Storage of accessories.
Attach onto attachment hose with unit in blower mode
only to apply water-based, non-flammable liquids.
31
Portable Sprayer
32
33
To transform unit from upright to portable position by
removing upright handle and inserting portable handle.
Aids in cleaning of carpeted stairs and mattress cleaning.
Portable Handle
Portable Shampooer Cap Attach onto portable sprayer with unit in blower mode
to apply Kirby® Carpet Shampoo for spot cleaning.
34
35
Skin/scalp massage. Clean the floors of cars.
Massage Cup
Inflator/Deflator Tool
With unit in blower mode, use to inflate toys, air
mattresses or other low-pressure inflatable items up to
1 p.s.i. With unit in canister mode, use to deflate objects.
36
37
Duster Brush
With or without extension tubes on contoured or
irregular surfaces.
Upholstered furniture, carpeted stairs, clothing.
Vehicle interiors.
Upholstery Nozzle
39
40
Wall and Ceiling Brush
Suction Control Grip
Walls, ceilings, drapes and other surfaces.
Use when needing to control amount of suction such as
drapes and delicate lampshades. Use with or without
extension tubes.
41
42
43
44
Extend reach and use with other tools.
Convert from upright to canister or blower mode.
Emergency back up supply.
Extension Tubes
Attachment Hose
Replacement Belt
Without brash, use on cracks, crevices, corners, grooves
and narrow openings. With brush use on corners, button
tufts, between radiator coils and sliding window tracks.
Crevice Tool with
Removable Brash
45
46
47
48
49
Surface Nozzle
Air Intake Guard
Zippbrush
Bare floors, surface cleaning carpets and under low furniture.
Place on front of unit to convert unit into a blower.
Upholstery, carpeted stairs. Automotive interiors.
Turbo Accessory System Sander, Buffer, Scouring, Massaging.
For Hardwood, Vinyl, Cork and Linoleum floors.
Apply with roller waxer applicator.
Miracle Waxer®
Floor Polisher
Handi-Butler® Tool
Cleaning and polishing.
50
70
Download from Www.Somanuals.com. All Manuals Search And Download.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
The following information need only apply when changing plugs on Sentria™ models
that are used in the U.K., Australia, South Africa and New Zealand.
The wires in the main lead are coloured in accordance with the following code:
Blue
Neutral
Brown
Live
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured marking identifying
the terminals in your plug, proceed as follows:
WARNING: DO NOT connect either wire to the terminal marked "E" or with the earth
=
symbol. No wire is con•
nected to this terminal. The wire which is coloured Blue must be connected to the terminal which is marked with the letter
N or coloured black. The wire which is coloured Brown must be connected to the terminal which is marked with the letter
L or coloured red. If a U.K.: 13A (BS 1363) plug is used, fit a 5A fuse. For any other type plug, protect with a 5A fuse or
fuse wire in the adaptor or distribution board. If the plug does not fit the sockets in the user's house, it should be cut off
and safely disposed of and the correct plug fitted.
The Sentria™ Model G10E is approved by the British Electrotechnical Approvals Board (BEAB).
Warning:
There is a shock hazard if a plug that has been cut from
the supply cord is inserted in a 13A socket outlet. Any
replacement fuse in the plug must be an ASTA approved
BS1362 5A fuse in the U.K.
Warning:
If the fuse cover is removable, never use the plug with the
fuse cover removed.
If supply cord is damaged and needs to be replaced, the replacement part number is: 890806-Australia/New Zealand;
890906-Continental Europe; 890706-South Africa; 890606-United Kingdom; 192006-U.S.A.;
P/N 260006 Rev. B - U.S., Canada and U.K.
©2006 The Scott Fetzer Company
Printed in U.S.A.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
|